1. No category

Roof entry
Swan neck SHD
Flat roof entry in 4 sizes
ID 100 e.g. for 4 cables up to Ø 28 mm
Article code: SHD 100
ID 150 e.g. for 7 cables up to Ø 28 mm
Article code: SHD 150
ID 200 e.g. for 12 cables up to Ø 28 mm
Article code: SHD 200
ID 300 e.g. for 20 cables up to Ø 28 mm
Article code: SHD 300
Features and technical data:
• flexible, modular system design suitable for all flat roof structures
• easy to draw cables through
• height and orientation can be adjusted
(can be swivelled through 360°) even after installation
• available in 4 sizes, 100, 150, 200 and 300 mm diameters
• simple transportation and easier assembly of the hot-dip galvanised
elements, as they can be assembled on site
• variable and retrofit configuration possible together with
split SKD seal insert (press plates made of stainless steel V2A (AISI 304L))
Accessories
Cable seal for SHD swan neck
SHD100 e.g. for 4 cables up to Ø 28 mm
Article code: SKD 100-2G-Z/d
SHD150 e.g. for 7 cables up to Ø 28 mm
Article code: SKD 150-2G-Z/d
SHD200 e.g. for 12 cables up to Ø 28 mm
Article code: SKD 200-2G-Z/d
SHD300 e.g. for 20 cables up to Ø 28 mm
Article code: SKD 300-2G-Z/d
Roof entries - for special requirements
This special flat roof entry design enables the easy installation and sealing of solar, mobile radio communication and air-conditioning cables to
match the respective roof structure. The swan neck SHD flat roof entry is suitable for dowelling above core drill holes and can be swivelled through
360°. The overall height is adjustable by at least 300 mm and features a height-adjustable drip cap. For sealing we have developed especially for
the flat roof entries our cable sealing SKD.
cablepipebuildingentry+
A (mm)
B (mm)
C ( mm)
D (ID mm)
E ( mm)
Article code
600 – 950
1050 – 1400
250
100
300
SHD 100
600 – 950
1175 – 1525
300
150
350
SHD 150
600 – 950
1300 – 1650
350
200
400
SHD 200
600 – 950
1550 – 1900
450
300
500
SHD 300
A = telescope range min./max.
B = overall height
C = hole pattern 4 x Ø 12 mm
D = max. core drilling diameter
E = base plate edge dimension
B
200
intermediate pipe
(can be removed)
drip cap
header
membrane
500
A
height-adjustable
extension pipe
insulation
membrane
D
C
E
base plate
Practical examples
installed SHD 200 before installation of the flat roof seal
Hauff-Technik GmbH & Co. KG
Robert-Bosch-Straße 9
89568 Hermaringen, GERMANY
installed seal insert SKD in swan neck SHD 200
Tel. +49 7322 1333-0
Fax +49 7322 1333-999
[email protected]
www.hauff-technik.de
dachdurchf_shd_en_140807
pipe elbow 30°
pipe elbow 90°
The information in this publication represents our current state of technical knowledge and experience. However, given the multitude of possible influences affecting the processing and use of our products, this information does not exempt processors and users from
running their own tests and trials. We will replace any parts that cannot be used due to defective materials. We do not replace parts for defects caused due to transport, storage or faulty installation and the consequences thereof. All information without guarantee.
Roof entry swan neck SHD
Technical data