SCOPE OF ACCREDITATION CAMBRIDGE MATERIALS TESTING LIMITED 1177 Franklin Blvd. Cambridge, ON N1R 7W4 Accredited Laboratory No. 59 (Conforms with requirements of CAN-P-4E (ISO/IEC 17025:2005)) CONTACT: TEL: FAX: EMAIL: URL: Ms. Jill Cook +1 519 621 6600 +1 519 621 6082 [email protected] www.cambridgematerials.com CLIENTS SERVED: Commercial any party FIELDS OF TESTING: Chemical/Physical, Mechanical/Physical, Thermal & Fire Resistance ISSUED ON: 2015-05-12 VALID TO: 2017-08-08 ELASTOMERS AND PROTECTIVE AND OTHER COATINGS Adhesives (Organic Resins) and Glues: Adhesives ASTM D1002 ASTM D1876 ASTM D3163 ASTM D3164 ASTM D3165 ASTM D3167 ASTM D3330 Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading Peel Resistance of Adhesives (T-Peel Test) Test Method for Determining the Strength of Adhesively Bonded Rigid Plastic Lap-Shear Joints in Shear by Tension Loading Strength Properties of Adhesively Bonded Plastic Lap-Shear Sandwich Joints in Shear by Tension Loading Strength Properties of Adhesives in Shear by Tension Loading of Single-Lap-Joint Laminated Assemblies Test Method for Floating Roller Peel Resistance of Adhesives Peel Adhesion of Pressure Sensitive Tape The approved and most recent version of this document can be viewed on the SCC website at http://palcan.scc.ca/SpecsSearch/GLSearchForm.do Page 1 of 17 Standards Council of Canada Accredited Laboratory No. 59 ASTM D6862 ASTM D816 ASTM D903 ASTM D904 FLTM BU 112-02 GM 9774P GM 9838P SAE J1525 Standard Test Method for 90° Peel Resistance of Adhesives Test Methods for Rubber Cements Only for: Method A, B, C Test Method for Peel or Stripping Strength of Adhesive Bonds Exposure of Adhesive Specimens to Artificial Light Peel Adhesion of Pressure Sensitive Tapes Only for: Method A, B, D, E Molding and Emblem Adhesion Test Pluck Resistance Tape Lamination to Automotive Components Lap Shear Test for Automotive-Test Adhesives for Fibre Reinforced Plastic (FRP) Bonding Paints; Varnishes; Inks; Coatings; and Allied Products: Application and Working Properties Refer to minor sub-heading: Paints and Protective Coatings Applied Coatings Performance see also All Forms, Articles of Metal Fabrics AMS-QQ-P-416 ASTM A428/A428M ASTM A90/A90M ASTM B117 ASTM B136 ASTM B137 ASTM B244 ASTM B368 ASTM B456 Plating, Cadmium (Electrodeposited) Only for: Adhesion Par. 4.6.2 Hydrogen Embrittlement Relief Test Par. 4.6.4.1 Test Method for Weight of Coating on Aluminum Coated Iron or Steel Articles Standard Test Method for Weight {Mass} of Coating on Iron and Steel Articles with Zinc or Zinc Alloy Coatings Standard Practice for Operating Salt Spray (Fog) Apparatus Measurement of Stain Resistance of Anodic Coatings on Aluminum Test Method for Measurement of Coating Mass Per Unit Area on Anodically Coated Aluminum Method for Measurement of Thickness of Anodic Coatings on Aluminum and of other Non-conductive Coatings on Non-magnetic Base Metals with Eddy-Current Instruments Method for Copper-Accelerated Acetic Acid-Salt Spray (Fog) Testing (CASS Test) Standard Specification for Electrodeposited Coatings of Copper Plus Nickel Plus Chromium and Nickel Plus The approved and most recent version of this document can be viewed on the SCC website at http://palcan.scc.ca/SpecsSearch/GLSearchForm.do Page 2 of 17 Standards Council of Canada Accredited Laboratory No. 59 ASTM B487 ASTM B499 ASTM B571 ASTM B578 ASTM B680 ASTM B700 ASTM B767 ASTM C633 ASTM D1654 ASTM D1735 ASTM D2247 ASTM D2794 ASTM D3170 ASTM D3359 ASTM D3363 ASTM D4060 ASTM D4585//D4585M ASTM D522 ASTM D610 ASTM D7091 ASTM D714 ASTM D870 ASTM D968 Chromium (Dubpernell Test) Only for: Appendix X4 Test Method for Measurement of Metal and Oxide Coating Thickness by Microscopical Examination of a Cross Section Test Method for Measurement of Coating Thickness by the Magnetic Method; Non-magnetic Coatings on Magnetic Basis Metals Practice for Qualitative Adhesion Testing of Metallic Coatings Except for: Sections 6, 11, 12 Microhardness of Electroplated Coatings Seal Quality of Anodic Coatings on Aluminum by Acid Dissolution Electrodeposited Coatings of Silver for Engineering Use Only for: Embrittlement Relief Test, Para. 8.4 Guide for Determining Mass Per Unit Area of Electrodeposited and Related Coatings by Gravimetric and Other Chemical Analysis Procedures Adhesion or Cohesion Strength of Thermal Spray Coatings Test Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus Practice for Testing Water Resistance of Coatings in 100% Relative Humidity Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact) Test Method for Chip Resistance of Coatings Test Methods for Measuring Adhesion by Tape Test Test Method for Film Hardness by Pencil Test Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser Standard Practice for Testing Water Resistance of Coatings Using Controlled Condensation Mandrel Bend Test of Attached Organic Coatings Only for: Method B - Cylindrical Mandrel Test Standard Practice for Evaluating Degree of Rusting on Painted Steel Surfaces Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals Test Method for Evaluating Degree of Blistering of Paints Testing Water Resistance of Coatings Using Water Immersion Abrasion Resistance of Organic Coatings By Falling Abrasive Only for: Method A - Falling Sand The approved and most recent version of this document can be viewed on the SCC website at http://palcan.scc.ca/SpecsSearch/GLSearchForm.do Page 3 of 17 Standards Council of Canada Accredited Laboratory No. 59 ASTM E376 ASTM F519 ASTM G154 ASTM G155 FED-STD-141 FLTM AQ 101-01 FLTM BI 106-01 FLTM BI 108-01 FLTM BN 108-02 FLTM BQ 007-02 FLTM BQ 104-02 FLTM BQ 105-01 FMVSS 209 GM 9500P GM 9501P GM 9503P GM 9505P GM 9509P GMW 14124 GMW 14458 GMW 14700 GMW 14729 GMW 14829 GMW 14864 GMW 15282 GMW 15288 GMW 3286 ISO 10289 ISO 1463 Measuring Coating Thickness by Magnetic Field or Eddy Current (Electromagnetic) Test Methods Standard Test Method of Mechanical Hydrogen Embrittlement Evaluation of Plating / Coating Processes and Service Environments Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Nonmetallic Materials Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials Abrasion Resistance (Taber Abraser) Only for: Method 6192 Determination of Phosphate Coating Weights - Chromic Acid Method Paint Adhesion Test Impact Test for Painted Panels Resistance to Abrasion-Taber Abraser Acid Dissolution Test Decorative Aluminum Parts Humidity Resistance Testing Copper-Accelerated Acetic Acid Salt Spray Testing (CASS Test) Seat Belt Assemblies Only for: Hardware; Corrosion Resistance, Sec. S5.2(a) Gasoline Puddle Test Gasoline Dip Test Evaluating Brittleness of Painted Plastics and Sealants by Means of a Mandrel Automotive Environmental Cycles Solvent Rub Method for Determining Cure of Painted Metal or Plastic Substrates Automotive Environmental Cycles Except for: Cycle T Copper-Accelerated Acetic Acid Salt Spray (CASS) Test Stone Impact Resistance of Coatings Only for: Method B and C Procedures for High Humidity Test, Option A: Water Fog, Option B: Wet Bottom Tape Adhesion Test for Paint Finishes Procedure for Determining the Staining of Trim Components Due to Sulfur Dioxide, SO2, and Hydrogen Sulfide, H2S Corrosion/Undercutting Scribe Creepback Scab Corrosion Creepback of Paint Systems on Metal Substrates Procedure for Neutral Salt Spray Test Methods for corrosion testing of metallic and other inorganic coatings on metallic substrates - Rating of test specimens and manufactured articles subjected to corrosion tests. Metallic and Oxide Coatings - Measurement of Coating Thickness Microscopic Method The approved and most recent version of this document can be viewed on the SCC website at http://palcan.scc.ca/SpecsSearch/GLSearchForm.do Page 4 of 17 Standards Council of Canada Accredited Laboratory No. 59 ISO 2106 ISO 2808 ISO 3210 ISO 9227 SAE J1767 SAE J2334 SAE J2412 SAE J2527 SAE J400 Anodizing of Aluminum and its Alloys-Determination of Mass per Unit Area (Surface Density) of Anodic Oxide Coatings-Gravimetric Method Paints and Varnishes - Determination of Film Thickness Only for: Methods 6A, 6B, 7C, 7D Anodizing of Aluminum and its Alloys-Assessment of Quality of Sealed Anodic Oxide Coatings by Measurement of the Loss of Mass after Immersion in Phosphoric-Chromic Acid Solution Corrosion Tests in Artificial Atmospheres-Salt Spray Tests Instrumental Colour Difference Measurements for Colorfastness of Automotive Interior Trim Materials Cosmetic Corrosion Lab Test Accelerated Exposure of Automotive Interior Trim Components Using a Controlled Irradiance Xenon-Arc Apparatus Performance Based Standards for Accelerated Exposure of Automotive Exterior Materials Using a Controlled Irradiance Xenon-Arc Apparatus Test for Chip Resistance of Surface Coatings Colour and Appearance see also Fabrics Applied Coatings Performance ASTM D2244 ASTM D523 ASTM E1164 ASTM E1347 CLP-463PB-31-01 FLTM BI 110-01 FLTM BI 113-07 GM 9741P SAE J1545 Standard Practice for Calculation of Colour Tolerances and Colour Differences from Instrumentally Measured Colour Co-ordinates Test Method for Specular Gloss Standard Practice for Obtaining Spectrophotometric Data for Object-Color Evaluation Colour and Colour-Difference Measurement by Tristimulus (Filter) Colorimetry Resistance of Paint Films to Various Fluids Except for: Method I Measurement of the Gloss of Paint Panels Resistance to Synthetic Perspiration Staining Instrumented Colour Measurement Instrumental Colour Difference Measurement for Exterior Finishes, Textiles and Coloured Trim Paints and Protective Coatings ASTM D2369 Test Methods for Volatile Content of Coatings The approved and most recent version of this document can be viewed on the SCC website at http://palcan.scc.ca/SpecsSearch/GLSearchForm.do Page 5 of 17 Standards Council of Canada Accredited Laboratory No. 59 Plastics; Resins and Rubbers: Plastics see also Fabrics Resins and Rubbers Colour and Appearance Construction Materials Applied Coatings Performance ASTM D1003 ASTM D1004 ASTM D1238 ASTM D1525 ASTM D1693 ASTM D1790 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics Only for: Appendix X2 Standard Test Methods for Tear Resistance (Graves Tear) of Plastic Film and Sheeting Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer Only for: Method A Test Method for Vicat Softening Temperature of Plastics Standard Test Method for Environmental Stress Cracking of Ethylene Plastics Test Method for Brittleness Temperature of Plastic Film by Impact ASTM D1822 Test Method for Tensile-Impact Energy to Break Plastic and Electrical Insulating Materials ASTM D2457 Test Method for Specular Gloss of Plastic Film and Solid Plastics Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics Only for: Methods A, C and E Xenon-Arc Exposure of Plastics Intended for Outdoor Applications Standard Specification for Strapping, Non-metallic (and Joining Methods) Test Methods for Impact Resistance of Rigid Polyvinylchloride (PVC) Building Products Standard Practice for Fluorescent Ultraviolet (UV) Lamp Apparatus Exposure of Plastics Standard Practice for Xenon-Arc Exposure of Plastics Intended for Indoor Applications ASTM D256 ASTM D2565 ASTM D3950 ASTM D4226 ASTM D4329 ASTM D4459 The approved and most recent version of this document can be viewed on the SCC website at http://palcan.scc.ca/SpecsSearch/GLSearchForm.do Page 6 of 17 Standards Council of Canada Accredited Laboratory No. 59 ASTM D4812 ASTM D5420 ASTM D570 ASTM D6109 ASTM D6110 ASTM D6272 ASTM D6341 ASTM D635 ASTM D638 ASTM D648 ASTM D6662 ASTM D695 ASTM D696 ASTM D7032 ASTM D732 ASTM D746 ASTM D785 ASTM D790 ASTM D792 ASTM D882 ASTM F2231 CLP-463LB-12-01 Un-notched Cantilever Beam Impact Resistance of Plastics Test Method for Impact Resistance of Flat Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact) Test Method for Water Absorption of Plastics Test Methods for Flexural Properties of Unreinforced and Reinforced Plastic Lumber Test method for determining the Charpy Impact Resistance of Notched Specimens of Plastics Standard Test Method for Flexural Properties of Un-reinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending Test Method for Determination of the Linear Coefficient of Thermal Expansion of Plastic Lumber and Plastic Lumber Shapes Between -30 and 140°F (-34.4 and 60°C) Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position Test Method for Tensile Properties of Plastics Test Method for Deflection Temperature of Plastics Under Flexural Load Polyolefin-Based Plastic Lumber Decking Boards Except for: Sec. 6.3.1 - Test Procedure for Surface Appearance Changes (Xenon Exposure) Sec. 6.3.3 - Hygrothermal Cycling Sec. 6.4 - Fire Properties Test Method for Compressive Properties of Rigid Plastics Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between -30ºC and 30°Cwith aVitreous Silica Dilatometer Establishing Performance Ratings for Wood-Plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails) Except for: Biodetermination Tests and Fire Performance Tests Shear Strength of Plastics by Punch Tool Test Method for Brittleness Temperature of Plastics and Elastomers by Impact Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials Test Methods for Flexural Properties of Un-reinforced and Reinforced Plastics and Electrical Insulating Materials Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement Test Methods for Tensile Properties of Thin Plastic Sheeting Charpy Impact Test on Thin Specimens of Polyethylene Used in Pressurized Pipes Resistance to Humidity Hot and Cold Cycling of Trim Materials The approved and most recent version of this document can be viewed on the SCC website at http://palcan.scc.ca/SpecsSearch/GLSearchForm.do Page 7 of 17 Standards Council of Canada Accredited Laboratory No. 59 FLTM BN 024-02 FLTM BO 115-01 FMVSS 302 GM 9126P GM 9128P GM 9131P GM 9133P GM 9141P GM 9143P GM 9150P GM 9160P GM 9200P GM 9302P GM 9773P GMW 14093 GMW 14334 GMW 3205 GMW 3232 GMW 3259 ICC-ES AC174 ISO 1133-1 ISO 1183-1 ISO 178 ISO 179-1 ISO 180 ISO 291 ISO 306 ISO 3795 Flammability Test for Automotive Interior Materials Plastics - Resistance to Artificial Weathering Flammability of Interior Polymeric Materials, Horizontal Test Method Test for Cleanability of Textiles and Plastics Mildew Growth Colour Change Due to Temperature and Humidity Resistance to Water Spotting, Finish Disturbance, Salt Staining, and Discolouration Compatibility of Plastic Rolled Goods and Leather to White Vinyl and to White Leather Crazing of Vinyl Trim Materials Resistance to Marring or Scuffing Top Coat Adhesion of Vinyls Accelerated Aging Except for: Section 4.2 Steaming Test for Stress Mark Susceptibility of Plastic Materials Cold Slam Test Determination of Impact Resistance of Plastic Components Except for: Method B Chemical Resistance to Fluids Test Method for Determining the Resistance to Odour Propagation of Interior Materials Test Method for Determining the Flammability of Interior Trim Materials Mildew Resistance ICC Evaluation Services, Inc. - Acceptance Criteria for Deck Board Span Ratings and Guardrail Systems (Guards and Handrails) Except for: Sec. 3.9 - Termite and Decay, Sec. 3.10 Flame Spread and Sec.3.11 Duration of Load Plastics-Determination of the Melt Mass-Flow Rate (MFR) and the Melt Volume-Flow Rate (MVR) of Thermoplastics Part 1: Standard Method Only for: Procedure A Plastics-Methods for Determining the Density of Non-Cellular Plastics Only for: Method A Plastics-Determination of Flexural Properties Plastics-Determination of Charpy Impact Strength Part 1: Non-instrumented Impact Test Plastics-Determination of Izod Impact Strength Plastics-Standard Atmospheres for Conditioning and Testing Plastics-Thermoplastic Materials-Determination of Vicat Softening Temperature (VST) Road Vehicles and Tractors and Machinery for Agriculture and Forestry-Determination of Burning Behavior of Interior Materials The approved and most recent version of this document can be viewed on the SCC website at http://palcan.scc.ca/SpecsSearch/GLSearchForm.do Page 8 of 17 Standards Council of Canada Accredited Laboratory No. 59 ISO 527-1 ISO 527-2 ISO 604 ISO 62 ISO 75-1 ISO 75-2 ISO 974 SAE J369 Plastics-Determination of Tensile Properties Part 1: General Principles Plastics-Determination of Tensiles Properties Part 2: Test Conditions for Moulding and Extrusion Plastics Plastics Determination of Compressive Properties Plastics-Determination of Water Absorption Plastics-Determination of Temperature of Deflection Under Load Part 1: General Test Methods Plastics-Determination of Temperature of Deflection Under Load Part 2: Plastics and Ebonite Plastics-Determination of the Brittleness Temperature by Impact Flammability of Polymeric Interior Materials-Horizontal Test Method Resins and Rubbers see also Applied Coatings Performance Plastics ASTM D1056 ASTM D1229 ASTM D1414 ASTM D2137 ASTM D2240 ASTM D3574 ASTM D395 ASTM D412 ASTM D413 ASTM D429 ASTM D573 Specification for Flexible Cellular Materials -Sponge or Expanded Rubber Test Method for Rubber Property - Compression Set at Low Temperature Standard Test Methods for Rubber O-Rings Except for: Tension Set Test, Low-Temperature Test, O-ring Mold Shrinkage Test Standard Test Methods for Rubber Property-Brittleness Point of Flexible Polymers and Coated Fabrics Test Method for Rubber Property - Durometer Hardness Test Methods for Flexible Cellular Materials - Slab, Bonded, and Molded Urethane Foams Only for: Tests A, B1, B2, C, D, E, F, K Test Methods for Rubber Property - Compression Set Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers - Tension Test Methods for Rubber Property-Adhesion to Flexible Substrate (Machine Method) Test Methods for Rubber Property-Adhesion to Rigid Substrates Only for: Method A Test Method for Rubber Deterioration in an Air Oven The approved and most recent version of this document can be viewed on the SCC website at http://palcan.scc.ca/SpecsSearch/GLSearchForm.do Page 9 of 17 Standards Council of Canada Accredited Laboratory No. 59 ASTM D575 ASTM D624 ASTM D925 ISO 815-1 ISO 815-2 Rubber Properties in Compression Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomer Standard Test Methods for Rubber Property - Staining of Surfaces (Contact, Migration and Diffusion) Only for: Method A Rubber, Vulcanized or Thermoplastic-Determination of Compression Set-Part 1:At Ambient or Elevated Temperatures Rubber, Vulcanized or Thermoplastic-Determination of Compression Set -Part 2: At Low Temperatures METALLIC ORES AND PRODUCTS Articles of Metal: All Forms, Articles of Metal AASHTO T244 AMS 2315 AMS 2485 ASTM A247 ASTM A255 ASTM A262 ASTM A370 ASTM A561 ASTM A604/A604M ASTM A799/A799M ASTM A800/A800M ASTM A923 ASTM B557 ASTM D3953 ASTM E10 ASTM E1019 Standard Method of Test for Mechanical Testing of Steel Products Determination of Delta Ferrite Content Coating, Black Oxide Only for: Surface and Intergranular Attack, Para. 3.3.4 Test Method for Evaluating the Microstructure of Graphite in Iron Castings Standard Test Methods for Determining Hardenability of Steel Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels Test Methods and Definitions for Mechanical Testing of Steel Products Macroetch Testing of Tool Steel Bars Macroetch Testing of Consumable Electrode Remelted Steel Bars and Billets Standard Practice for Steel Castings, Stainless, and Instrument Calibration for Estimating Ferrite Content Standard Practice for Steel Casting, Austenitic Alloy, Estimating Ferrite Content Thereof Detecting Detrimental Intermetallic Phase in Duplex Austenitic/Ferritic Stainless Steels Method of Tension Testing Wrought and Cast Aluminum and Magnesium Alloy Products Standard Specification for Strapping, Flat Steel and Seals Test Method for Brinell Hardness of Metallic Materials Test Methods for Determination of Carbon, Sulphur, Nitrogen and Oxygen in Steel, Iron, Nickel and Cobalt Alloys The approved and most recent version of this document can be viewed on the SCC website at http://palcan.scc.ca/SpecsSearch/GLSearchForm.do Page 10 of 17 Standards Council of Canada Accredited Laboratory No. 59 ASTM E1077 ASTM E1097 CMTL Modified ASTM E111 ASTM E112 ASTM E1180 ASTM E1181 ASTM E1245 ASTM E1268 ASTM E1382 ASTM E139 ASTM E140 ASTM E1409 ASTM E1447 ASTM E1447 Applied to Steel ASTM E1479 ASTM E18 ASTM E21 ASTM E23 ASTM E290 ASTM E292 ASTM E3 ASTM E340 ASTM E345 Test Methods for Estimating the Depth of Carburization of Steel Specimens Standard Guide for Determination of Various Elements by Direct Current Plasma Emission Spectrometry Analysis (Modified for ICP Argon Optical Emission Spectrometry) Test Method for Young s Modulus, Tangent Modulus and Chord Modulus Test Methods for Determining the Average Grain Size Standard Practice for Preparing Sulfur Prints for Macrostructural Evaluation Test Methods for Characterizing Duplex Grain Sizes Standard Practice for Determining the Inclusion or Second Phase Constituent Content of Metals by Automatic Image Analysis Standard Practice for Assessing the Degree of Banding or Orientation of Microstructures Analysis Test Methods for Determining Average Grain Size Using Semiautomatic and Automatic Image Analysis Standard Test Methods for Conducting Creep, Creep-Rupture, and Stress Rupture Tests of Metallic Materials (only for Stress Rupture) Only for: Stress Rupture Standard Hardness Conversion Tables for Metals Relationship Among Brinell Hardness, Vickers Hardness, Rockwell Hardness, Superficial Hardness, Knoop Hardness, Scleroscope Hardness and Leeb Hardness Determination of Oxygen and Nitrogen in Titanium and Titanium Alloys by Inert Gas Fusion Determination of Hydrogen in Titanium and Titanium Alloys by the Inert Gas Fusion Thermal Conductivity/Infrared Detection Method Determination of Hydrogen in Titanium and Titanium Alloys by the Inert Gas Fusion Thermal Conductivity/Infrared Detection Method Practice for Describing and Specifying Inductively-Coupled Plasma Optical Emission Spectrometers Standard Test Methods for Rockwell Hardness of Metallic Materials Elevated Temperature Tension Tests of Metallic Materials Test Methods for Notched Bar Impact Testing of Metallic Materials Standard Test Method for Bend Testing of Material for Ductility Standard Test Methods for Conducting Time-for-Rupture Notch Tension Tests of Materials Standard Guide for Preparation of Metallographic Specimens Method for Macroetching Metals and Alloys Test Methods of Tension Testing of Metallic Foil The approved and most recent version of this document can be viewed on the SCC website at http://palcan.scc.ca/SpecsSearch/GLSearchForm.do Page 11 of 17 Standards Council of Canada Accredited Laboratory No. 59 ASTM E381 ASTM E384 ASTM E407 ASTM E45 ASTM E517 ASTM E562 ASTM E646 ASTM E768 ASTM E8/E8M ASTM E883 ASTM E9 ASTM E930 ASTM F2328 ASTM G28 ASTM G34 ASTM G46 ASTM G48 GMW 3335 ISO 10113 ISO 10275 ISO 148-1 ISO 3274 ISO 4287 Standard Method of Macroetch Testing Steel Bars, Billets, Blooms and Forgings Standard Test Method for Knoop and Vickers Hardness of Materials Only for: 50g to 50kg load Standard Practice for Microetching Metals and Alloys Standard Test Methods for Determining the Inclusion Content of Steel Except for: Magnetic Particle Method Test Method for Plastic Strain Ratio r for Sheet Metal Standard Test Method for Determining Volume Fraction by Systematic Manual Point Count Test Method for Tensile Strain Hardening Exponents (n-Values) of Metallic Sheet Materials Standard Guide for Preparing and Evaluating Specimens for Automatic Inclusion Assessment of Steel Standard Test Methods for Tension Testing of Metallic Materials Standard Guide for Reflected-Light Photomicrography Standard Test Methods of Compression Testing of Metallic Materials at Room Temperature Test Methods for Estimating the Largest Grain Observed in a Metallographic Section (ALA Grain Size) Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs Test Methods of Detecting Susceptibility to Intergranular Corrosion in Wrought, Nickel Rich, Chromium-Bearing Alloys Exfoliation Corrosion Susceptibility in 2XXX and 7XXX Series Aluminum Alloys (EXCO Test) Standard Guide for Examination and Evaluation of Pitting Corrosion Except for: Nondestructive Inspection Pitting and Crevice Corrosion Resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride Solution Metallic Sheet, Mechanical Properties Testing Metallic Materials - Sheet and Strip - Determination of Plastic Strain Ratio Metallic Materials - Sheet and Strip - Determination of Tensile Strain Hardening Exponent Charpy Pendulum Impact Test - Test Method Geometrical Product Specifications (GPS) - Surface Texture: Profile Method - Nominal Characteristics of Contact (Stylus) Instruments Geometrical Product Specifications (GPS) - Surface Texture: Profile Method - Terms, Definitions and Surface Texture Parameters The approved and most recent version of this document can be viewed on the SCC website at http://palcan.scc.ca/SpecsSearch/GLSearchForm.do Page 12 of 17 Standards Council of Canada Accredited Laboratory No. 59 ISO 643 ISO 6507-1 ISO 6508-1 ISO 6892-1 ISO 6892-2 SAE J406 SAE J417 SAE J419 SAE J422 SAE J423 SAE J911 Steels-Micrographic Determination of the Ferritic or Austenitic Grain Size Metallic Materials - Vickers Hardness Test Metallic Materials - Rockwell Hardness Test Metallic Materials-Tensile Testing, Part 1 Method of Test at Room Temperature Metallic Materials-Tensile Testing, Part 2 Method of Test at Elevated Temperature Methods of Determining Hardenability of Steels Hardness Tests & Hardness Number Conversion (Vickers, Brinell, & Rockwell Tests) Methods of Measuring Decarburization Microscopic Determination of Inclusions in Steel Methods of Measuring Case Depth Surface Texture Measurement of Cold Rolled Sheet Steel Welded ASME Boiler & Pressure Vessel Code Section II, Part C ASME Boiler & Pressure Vessel Code Section IX ASTM E190 AWS B4.0 CAN/CSA W48 CSA-Z662 GM 4491M GMW 14058 ISO 5817 Material Specifications-Welding Rods, Electrodes and Filler Metals Welding and Brazing Qualifications Except for: Liquid Penetrant Testing Test Method for Guided Bend Test for Ductility of Welds Standard Methods for Mechanical Testing of Welds Filler Metals and Allied Materials for Metal Arc Welding Oil and Gas Pipeline Systems Arc Spot, Plug and Slot Welding Specification Weld Acceptance Criteria and Repair Procedures for Arc Welds and Arc Brazes - Steel Welding Fusion-Welded Joints in Steel, Nickel, Titanium and Their Alloys (Beam Welding Excluded) Quality Levels for Imperfections Semi-Fabricated Products: (Extrusion, rolled sections) CAN/CSA-G40.20 CAN/CSA-G40.21 General Requirements for Rolled or Welded Structural Quality Steel Except for: L shape full section tensile testing Non - destructive testing Structural Quality Steels Tools, Fasteners and Hardware: see also All Forms, Articles of Metal ASTM A489 Specification for Carbon Steel Lifting Eyes The approved and most recent version of this document can be viewed on the SCC website at http://palcan.scc.ca/SpecsSearch/GLSearchForm.do Page 13 of 17 Standards Council of Canada Accredited Laboratory No. 59 ASTM A574 ASTM D1761 ASTM D6117 ASTM E894 ASTM E935 ASTM F541 ASTM F606 ASTM F606M ASTM F788 ASTM F812 ASTM F835 ISO 898 -1 NASM 1312 SAE J1199 SAE J122 SAE J238 SAE J429 SAE J430 SAE J773 SAE J995 Specification for Alloy Steel Socket-Head Cap Screws Standard Test Methods for Mechanical Fasteners in Wood Only for: Withdrawal Test & Lateral Resistance Test Standard Test Methods for Mechanical Fasteners in Plastic Lumber and Shapes Only for: Withdrawal Test & Lateral Resistance Test Standard Test Method for Anchorage of Permanent Metal Railing Systems and Rails for Buildings Standard Test Methods for Performance of Permanent Metal Railing Systems and Rails for Buildings Specification for Alloy Steel Eyebolts Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators and Rivets Except for: Section 5.6 Test Method for Measuring Compression Load (Direct Tension Indicators) Section 7. Test for Embrittlement of Metallic Coated Externally Threaded Fasteners Standard Test Methods for Determining Mechanical Properties of Externally and Internally Threaded Fasteners, Washers and Rivets (Metric) Except for: Section 7. Test for Embrittlement of Metallic Coated Externally Threaded Fasteners Annex A1. Test Method for Measuring Compression Load on Direct Tension Indicators Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series Standard Specification for Surface Discontinuities of Nuts, Inch and Metric Series Specification for Alloy Steel Socket Button and Flat Countersunk Head Cap Screws Mechanical Properties of Fasteners Made of Carbon Steel and Alloy Steel Part 1: Bolts, Screws and Studs with Specified Property Classes-Coarse Thread and Fine Pitch Thread Fastener Test methods Only for: 1, 6, 8, 10, 12 Mechanical and Material Requirements for Metric Externally Threaded Steel Fasteners Surface Discontinuities on Nuts Nut and Conical Spring Washer Assemblies Mechanical and Material Requirements for Externally Threaded Fasteners Mechanical and Chemical Requirements for Non-Threaded Fasteners Conical Spring Washers Mechanical and Material Requirements for Steel Nuts The approved and most recent version of this document can be viewed on the SCC website at http://palcan.scc.ca/SpecsSearch/GLSearchForm.do Page 14 of 17 Standards Council of Canada Accredited Laboratory No. 59 (Fasteners and Fastener Materials see also: Applied Coatings Performance All Forms, Articles of Metal Tools, Fasteners, and Hardware) TEXTILES AND FIBROUS MATERIALS Other (Leather see also: Plastics) CLP 463KC-21-01 Perspiration Resistance Textile Mill Products: (Including synthetic and natural fibres) Fabrics See also: Applied Coatings Performance Colour and Appearance Plastics AATCC EP1 AATCC EP2 AATCC EP8 AATCC TM8 ASTM D3884 ASTM D5034 ASTM D5035 ASTM D5587 CLP-463KB-02-01 CLP-463KB-21-01 CLP-463KC-13-01 FLTM AN 101-01 Grey Scale for Colour Change Grey Scale for Staining 9 Step Chromatic Transference Scale Colourfastness to Crocking: AATCC Crockmeter Method Standard Test Method for Abrasion Resistance of Textile Fabrics (Rotary Platform, Double Head Method) Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test) Standard Test Method for Breaking Force and Elongation of Textile Fabrics (Strip Method) Tearing Strength of Fabrics by Trapezoid Procedure Breaking Strength and Elongation Testing of Soft Trim Materials Wear Resistance of Trim Materials - Taber Method Flammability of Automotive Interior Trim Materials Fabrics Resistance of Textiles to Bleeding, Perspiration and Water Spotting The approved and most recent version of this document can be viewed on the SCC website at http://palcan.scc.ca/SpecsSearch/GLSearchForm.do Page 15 of 17 Standards Council of Canada Accredited Laboratory No. 59 FLTM BN 107-01 GM 9130P Crocking Test Test for Resistance to Odour of Textiles GMW 4217 ISO 105-A02 Dimensional Stability Textiles-Test for Colour Fastness (Grey Scale for Assessing Change in Colour) Hot Odour Test for Insulation Materials Method of Testing Resistance to Crocking of Organic Trim Materials Test Method for Wicking of Automotive Fabrics and Fibrous Materials Only for: Method C SAE J1351 SAE J861 SAE J913 WOOD PRODUCTS (AND PLASTIC LUMBER) Construction Materials: (Including for Furniture) (and Plastic Lumber Decking and Guardrails) ASTM D1037 ASTM D143 ASTM D2394 Standard Test Methods for Evaluating Properties of Wood Base Fiber and Particle Panel Materials Only for: Hardness Test; Water Absorption and Thickness Swelling Test Standard Test Methods for Small Clear Specimens of Timber Only for: Hardness Standard Methods for Simulated Service Testing of Wood and Wood-Base Finish Flooring Only for: Coefficient of Friction Notes: CAN-P-4E (ISO/IEC 17025:2005): General Requirements for the Competence of Testing and Calibration Laboratories (ISO/IEC 17025: 2005) Chantal Guay, ing., P. Eng. Vice President, Accreditation Services Date: 2015-05-12 Number of Scope Listings: 312 SCC 1003-15/80 Partner File #0 The approved and most recent version of this document can be viewed on the SCC website at http://palcan.scc.ca/SpecsSearch/GLSearchForm.do Page 16 of 17 Standards Council of Canada Accredited Laboratory No. 59 Partner: None The approved and most recent version of this document can be viewed on the SCC website at http://palcan.scc.ca/SpecsSearch/GLSearchForm.do Page 17 of 17
© Copyright 2026