LEXUS
GS 350
2013–
TVIP V4
REMOTE ENGINE STARTER (RES)
PREPARATION
Part #: PT398-00120
Will not program with Techstream Lite.
RES ECU Bracket
RES ECU
V4 Harness
Wire Tie
M6 Nut
Remote Label
Foam Tape
DISCARD
x1
x1
x1
x1
x10
PT398-89100-SS
Key Tag
x1
x2
08192-07820
Window Label
x2
PT398-60086
x2
PT398-60088
Engine Room
Label
Owner’s Guide
x1
x1
PT398-00070-EL
Service Part #’s
(may be required)
Safety Glasses
Safety Gloves
(Optional)
Techstream
Use latest version on TIS (Do not use Techstream Lite)
!
"
Screwdriver
#2 Phillips
Nylon Panel Removal Tool
e.g. Panel Pry Tool #1 Toyota SST# 00002-06001-01
Utility Knife
Side Cutters
Torque Wrench
Tape
Clear, Electrical
Socket
10mm, Extension
Issue: C 02/07/12
Cleaner
VDC Approved Cleaner
Glass Cleaner
Household Glass Cleaner
Page 1 of 22
LEXUS
GS 350
2013–
PREPARATION
TVIP V4
REMOTE ENGINE STARTER (RES)
$"
I. Preparation ............................................................................................................................ 1 – 3
1. Table of Contents ................................................................................................................................................2
2. Wire Routing Overview .......................................................................................................................................3
II. Procedure ............................................................................................................................4 – 1 9
1.
2.
3.
4.
6.
7.
Vehicle Disassembly . .........................................................................................................................................4
RES ECU Preparation and Installation. ..............................................................................................................8
V4 Harness Installation. ......................................................................................................................................9
Registration Preparation. ..................................................................................................................................12
Registration . .....................................................................................................................................................12
Complete the Installation. .................................................................................................................................18
Tag and Labels. .................................................................................................................................................19
III. Checklist ........................................................................................................................... 2 0 – 2 2
1. Accessory Function Checks ..............................................................................................................................20
2. Vehicle Function Checks ...................................................................................................................................21
()
Do not proceed until process
has been completed.
Follow steps carefully to
avoid damaging the Vehicle
or Accessory
Use caution to avoid injury.
Used in Figures to call attention
for the process.
Highlights a change in
installation with respect to
previous issue.
%&$"'
Care must be taken when installing this accessory to ensure damage does not
occur to the vehicle. The installation of this accessory should follow approved
guidelines to ensure a quality installation.
These guidelines can be found in the “Accessory Installation Practices”
document.
This document covers such items as:
Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.)
Safety (eye protection, checking torque procedure, etc.)
Vehicle Disassembly/Reassembly (panel removal, part storage, etc.)
Electrical Component Disassembly/Reassembly (battery disconnection,
connector removal, etc.)
Please see your LEXUS dealer for a copy of this document.
I
Indicates
that torque is related
tto safety.
Video available; click to play.
xx
Wire Tie location and number.
Issue: C 02/07/12
Page 2 of 22
A
Description
10P White
-
24P White
M
-
1P White
(for Registration)
N
-
1P White
(for Registration)
W
-
White Tape Marker
Z
-
RES ECU
GS 350
E
LEXUS
*+,!.
Vehicle
PREPARATION
Issue: C 02/07/12
TVIP
LEXUS GS 350 RES
2013–
Page 3 of 22
Z
E
A
N
M
TVIP V4
."+,//44+6
REMOTE ENGINE STARTER (RES)
W
LEXUS
GS 350
2013–
TVIP V4
REMOTE ENGINE STARTER (RES)
PROCEDURE
$%,//4
1
DS Step Cover
2
DS Cowl Cover
3
DS Dash Side Cover
4
DS Cluster Panel
Center Cluster Panel
6
Center Console DS Panel
7
DS Under Cover
8
Lower Dash Cover
6
4
3
8
2
7
1
Disconnect all Corresponding
Connectors.
10mm Socket
Fig. 1-1
76 $%6
a. Place the Vehicle in Park with
the Parking Brake set.
b. Disconnect the Negative
Battery Terminal.
Note the Battery Cable Position
as it will be re-installed in the
same position.
;,<
Do not touch the
Positive Terminal.
Issue: C 02/07/12
Page 4 of 22
LEXUS
GS 350
2013–
TVIP V4
REMOTE ENGINE STARTER (RES)
PROCEDURE
Nylon Panel Removal Tool
Fig. 1-2
c.
Remove the Driver’s Side
Step Cover.
Nylon Panel Removal Tool
Fig. 1-3
d. Remove the Driver’s Side
Cowl Cover.
Nylon Panel Removal Tool
Fig. 1-4
e. Remove the Driver’s Side
Dash Cover.
Apply Protective Tape on Pry
Area.
Issue: C 02/07/12
Page 5 of 22
LEXUS
GS 350
2013–
TVIP V4
REMOTE ENGINE STARTER (RES)
PROCEDURE
f.
Nylon Panel Removal Tool
Fig. 1-5
Remove the Driver’s Side
Cluster Panel.
Apply Protective Tape on Pry area.
Nylon Panel Removal Tool
Fig. 1-6
g. Remove the Center Cluster
Panel.
Apply Protective Tape on Pry area.
Disconnect “Engine Start Stop”
Button connector.
Nylon Panel Removal Tool
Issue: C 02/07/12
Fig. 1-7
Page 6 of 22
h. Remove the Center Console
Driver’s Side Panel.
LEXUS
GS 350
2013–
TVIP V4
REMOTE ENGINE STARTER (RES)
PROCEDURE
i.
Phillips Screwdriver
Fig. 1-8
Dislodge the Driver’s Side
Under Cover.
Remove 3 Screws.
;,<
Do not disconnect the
Vehicle’s Connectors.
Nylon Panel Removal Tool
j.
Wrap the Driver’s Side Under
Cover with a blanket and
place on a box to prevent
stress on Vehicle wires.
k.
Remove the Lower Dash
Cover.
Fig. 1-9
Disconnect all connectors.
l.
Nylon Panel Removal Tool
Fig. 1-10
Pull back on the Driver’s Side
Cowl Floor Carpet.
Gently pull back carpet to reveal
clip.
Press on clip and pull Cowl Carpet
away, disengaging hook-and-loop
tape.
Issue: C 02/07/12
Page 7 of 22
LEXUS
GS 350
2013–
TVIP V4
REMOTE ENGINE STARTER (RES)
PROCEDURE
Utility Knife
Fig. 2-1
=6 >>;
6
a. Cut the Foam Tape in half.
Discard the other half.
1/2 Foam Tape
1/2
/ Foam
oa Tape
ape
Fig. 2-2
b. Attach the Half Foam Tape to
the RES ECU.
c.
Fig. 2-3
Issue: C 02/07/12
Page 8 of 22
Attach the RES ECU Bracket
to the RES ECU.
LEXUS
GS 350
2013–
TVIP V4
REMOTE ENGINE STARTER (RES)
PROCEDURE
10mm Socket, Extension
Fig. 2-4
d. Position the RES ECU behind
the Vehicle brace and install
using the supplied Nut.
<,>
Make sure the Guide Pin
is seated correctly and Verify that
the Nut is tightened securely.
Fig. 3-1
Issue: C 02/07/12
Page 9 of 22
?6 @+6
a. Plug in the V4 White 24P
Connector to the RES ECU.
LEXUS
GS 350
2013–
TVIP V4
REMOTE ENGINE STARTER (RES)
PROCEDURE
Side Cutters
Fig. 3-2
b. Secure the V4 Harness White
Tape Marker to the Vehicle
Harness using 1 Wire Tie.
<,>
Make sure to route the
V4 Harness above the Hood
Release Cable.
1
c.
Side Cutters
Fig. 3-3
2
"4
Point of View
Good
DS
Cowl area
Vehicle
Harness
d. Secure the V4 Harness to
the Vehicle Harness using
1 Wire Tie.
V4
<,>
Route the V4 Harness
on the right side of the vehicle
harness as shown.
No Good
DS
Cowl area
V4
4
Route the V4 Harness’s
1P Diagnostic Connectors
toward the Driver’s Side
Cowl area.
Vehicle
hicle
Harnes
Harness
or V4
Side Cutters
Fig. 3-4
e. Secure the V4 Harness to
the Vehicle Harness using
1 Wire Tie and route toward
the Driver’s side under cover.
<,>
Make sure to route the
V4 Harness above the Hood
Release Cable.
3
Issue: C 02/07/12
Page 10 of 22
LEXUS
GS 350
2013–
TVIP V4
REMOTE ENGINE STARTER (RES)
PROCEDURE
f.
Side Cutters
Fig. 3-5
Connect the V4 White 10P
Connector to the Vehicle’s
10P Pre-Connector
g. Secure the V4 Harness to
the Vehicle Harness using
1 Wire Tie.
4
Side Cutters
Fig. 3-6
h. Secure the V4 Harness to
the Vehicle Harness using
1 Wire Tie.
5
i.
Side Cutters
Fig. 3-7
7
6
Issue: C 02/07/12
Page 11 of 22
Secure the V4 Harness to
the Vehicle Harness using
2 Wire Ties.
LEXUS
GS 350
2013–
TVIP V4
REMOTE ENGINE STARTER (RES)
PROCEDURE
Fig. 4-1
@6 )6
a. Verify that the Short Pin is
installed.
If not install now.
b. Reassemble the Vehicle
except for the Driver’s Cowl
and Step Covers.
>AB
!
properly, with no uneven gaps.
DO NOT INSTALL
>AB
That all Connectors are
plugged in.
"!$%
10mm Socket
C6 )6
a. Open the Hood.
b. Temporarily reconnect the
Negative Battery Cable.
;,<
Do not touch the
Positive Terminal.
c.
"!$&
Locate the 1P RES
Diagnostic Connectors in the
Driver’s Side Cowl Area and
connect them.
<,>
Once connected you will
have 10 minutes to complete this
section, steps d–ab.
d. Close all doors.
Issue: C 02/07/12
Page 12 of 22
LEXUS
GS 350
2013–
TVIP V4
REMOTE ENGINE STARTER (RES)
PROCEDURE
"!$=
e. Place the Vehicle in Park (P)
or Neutral (N) position.
f.
5
X
OFF
ACC
Cycle the “Engine Start Stop”
'*""*
times.
<,>
One cycle consists of:
*""+<+*
is equivalent to pressing the
“Engine Start Stop” Button 14
times.
ON
<,>
Do not apply Brake pedal.
(,,
For the Hazard Lights to
Flash Once.
g. Start the Engine.
"!$
h. After 10 seconds stop the
Engine.
(,,
For the Hazard Lights to
Flash Once.
A+,>;>A(>
The Hazard Lights won’t Flash or
Flashes Twice.
ON
OFF
Disconnect the V4 Harness’s 1P
RES Diagnostic Connectors.
Start again from step c.
Techstream
Issue: C 02/07/12
"!$
Page 13 of 22
;,<
Techstream Lite will
not work for this section, use the
Techstream Notebook ONLY.
i.
Connect the Techstream
Notebook to the Vehicle’s
Diagnostic Port.
j.
With the Smart Key in your
possession, press the
“Engine Start Stop” Button
twice to select the Ignition
“ON” position.
LEXUS
GS 350
2013–
TVIP V4
REMOTE ENGINE STARTER (RES)
PROCEDURE
k.
Start the TIS Techstream
Application by clicking on
the shortcut located on the
Desktop.
l.
Click “Connect to Vehicle”.
"!$@
"!$Q
TIS techstream
File Function
Setup
TIS
User
Help
TIS
techstream
Connect to Vehicle
Vehicle Connection Wizard(S301-04)
Select the Information and press Next
Open Scan Data File
m. >
displayed on the Vehicle
Connection Wizard is correct
for the vehicle. If not verify
that the Techstream is
properly connected.
Required Information:
Launch TIS
Division:
XXXXXX
n. Select w/Smart Key.
Model:
XXXXXXXXX
20XX
o. Click “Next>”.
New Users Demo
Check for Scantool
Updates
Model Year:
Generic OBD II
Software
Registration
User/Language
Selection
Engine:
XXXXXXXX
Option:
w/ Smart Key
Log Out
Optional Information:
xxxxxxxxxxxxxxxxxxx
VIN:
ABS
Memo:
Manual
Help
<Back
Next>
Cancel
Ver x.xx.xxx
p. Select “Smart Key”.
"!$
TIS techstream - 10645
File Function Setup TIS
System Select
User Help
Stored Data
System Selection Menu
Select desired system and then press Live Data to access the ECU.
Body or not responding.
Back Door
isMain
unsupported
Air
Conditioner
SRS Airbag
Note:
An astrisk (*) indicates
a system that
Combination Meter Main Body
*Sliding Roof
Tilt&Telescopic
Health Check
Customize
Setting
All ECUs
Powertrain
Chassis
Air Conditioner
SRS Airbag
Combination Meter Smart Key
*Accessory Gateway *Driver Door
Combination Meter Mirror
D Door Motor
Sliding Roof
*Passenger Door
Driver Seat
Occupant Detection
Body Electrical
Main Body
Occupant Detection
Back Door
D Door Motor
Sliding Roof
ECU
Reprogramming
CAN
Bus. Check
Print
Close
S601-03
Issue: C 02/07/12
Generic English
DLC3
Page 14 of 22
q. Click
.
LEXUS
GS 350
2013–
TVIP V4
REMOTE ENGINE STARTER (RES)
PROCEDURE
"!$]
r.
Click on “Utility”.
s.
Select “ECU Communication
ID Registration”.
t.
Click
TIS techstream - 10645
File Function Setup TIS
System Select
User Help
Stored Data
Customize
.
Utility Selection Menue
Select desired Utility and then press Next button.
Trouble Codes
Custimize
ECU Communication ID Registration
Smart Code Registration
Communication Check(Key Diag Mode)
Smart Code Erasure
Smart Code Reset
Data List
Active Test
Monitor
Utility
Print
Close
S601-03
Generic English
DLC3
u. Click “Next>”.
"!$%^
TIS techstream - 10645
File Function Setup TIS
System Select
User Help
Stored Data
Customize
Utility Selection Menue
ECU
Select desired Utility and
thenCommunication
press Next button. ID Registration (SMRT-13-001)
Welcome to the ECU Communication
ID
Communication Check(Key Diag Mode)
wizard.
Smart Code Erasure
Trouble Codes
Custimize
Registration
ECU Communication ID Registration
Smart Code Registration
Code Reset
This function is used to performSmart
the “hand
shake” procedure.
Data List
Confirm the following conditions:
Active Test
-The Engine is ON (IG)
-Smart Cancel Function is OFF
Monitor
Utility
Next>
Cancel
Print
Close
S601-03
Generic English
DLC3
v.
"!$%%
w. Click “Next>”.
TIS techstream - 10645
File Function Setup TIS
System Select
User Help
Stored Data
Custom ize
Utility Selection
Menue
ECU Communication
Select desired Utility and then press Next button.
Trouble Codes
Data List
ID Registration (SMRT-13-002)
Custimize
IDIDCode
Box and
ECU Communication
Registration
Smart Code Registration
Steering Lock
Communication Check(Key Diag Mode)
Smart Code Erasure
Smart Code Reset
Remote Engine Starter
Active Test
Monitor
Utility
Make a selection and press Next to “hand
shake” the selected ECU’s
<Back
Next>
Cancel
Print
Close
S601-03
Issue: C 02/07/12
Select “Remote Engine
Starter”.
Generic English
DLC3
Page 15 of 22
LEXUS
GS 350
2013–
TVIP V4
REMOTE ENGINE STARTER (RES)
PROCEDURE
"!$%&
,<AQ
That the ECU
Communication ID was
completed successfully.
TIS techstream - 10645
File Function Setup TIS
System Select
User Help
Stored Data
Custom ize
x.
Click “Exit”.
y.
Click
z.
Exit the vehicle.
Utility Selection Menue
ECU
Select desired Utility and
thenCommunication
press Next button. ID Registration (SMRT-13-002)
Trouble Codes
Custimize
ECU Communication ID Registration
Smart Code Registration
Communication Check(Key Diag Mode)
Smart Code Erasure
Smart Code Reset
Communication ID registration for Remote
Engine Starter is complete.
Data List
Active Test
Monitor
Utility
Exit
Print
Close
S601-03
Generic English
DLC3
"!$%=
.
TIS techstream - 10645
File Function Setup TIS
System Select
User Help
Stored Data
Customize
Utility Selection Menue
Select desired Utility and then press Next button.
Trouble Codes
Custimize
ECU Communication ID Registration
Smart Code Registration
Communication Check(Key Diag Mode)
Smart Code Erasure
Smart Code Reset
Data List
Active Test
Monitor
Utility
Print
Close
S601-03
Generic English
DLC3
"!$%
aa. Close the Hood.
ab. Look for the Hazard Lights
_`{!
is completed.
A+,>;>A(>
|}~!_
Times.
Disconnect the V4 Harness’s 1P
RES Diagnostic Connectors.
Start again from step c.
Issue: C 02/07/12
Page 16 of 22
LEXUS
GS 350
2013–
TVIP V4
REMOTE ENGINE STARTER (RES)
PROCEDURE
Fig. 5-15
ac. After a successful
Registration, disconnect
the 1P RES Diagnostic
Connectors.
ad. Secure the 1P RES
Diagnostic Connectors to
the Vehicle Harness using
Electrical Tape.
Fig. 5-16
Issue: C 02/07/12
Page 17 of 22
ae. Reinstall the Driver’s Side
Cowl Floor Carpet.
LEXUS
GS 350
2013–
TVIP V4
REMOTE ENGINE STARTER (RES)
PROCEDURE
Fig. 6-1
Y6 6
a. Finish reassembling the
Vehicle.
>AB
!
properly, with no uneven gaps.
>AB
That all Connectors are
plugged in.
b. Clean up and Remove trash.
c.
Sealed in its protective bag,
place the Owner’s Manual in
the Glove Box.
ALREADY INSTALLED
d. Position the Negative Battery
Cable at the original factory
position.
!'
Torque Wrench
Fig. 6-2
;,<
Do not touch the
positive terminal.
e. Reset the Power Windows.
Turn the ignition “ON”.
Lower the Windows halfway.
Pull up on the Power Window
Switches until the windows close.
Continue to hold up on the
switches for a minimum of 1 sec.
f.
Reset the Moon Roof.
(if equipped)
Turn the ignition “ON”.
Open the Moon Roof halfway.
Push and hold the Moon Roof
Switch to close until the Moon
Roof closes.
Continue to hold the switch for a
minimum of 1 sec.
Issue: C 02/07/12
Page 18 of 22
LEXUS
GS 350
2013–
TVIP V4
REMOTE ENGINE STARTER (RES)
PROCEDURE
Fig. 7-1
Z6 )($6
a. Using VDC approved cleaner
and cleaning method, clean
the area indicated in the
Engine Compartment Cover.
b. Attach the Engine Room
Warning Label as shown.
;,<
Do not touch the
adhesive surface.
c.
Attach the Key Tag.
Fig. 7-2
REPEAT: step c with the other Key.
d. Discard the Remote Labels.
Remote Label
DISCARD
x2
Fig. 7-3
Clear Tape
10 mm
f.
Use a piece of Clear Tape to
lift the Label off its protective
backing.
;,<
Do not touch the
adhesive surface.
PA R A L L E L
MOLDING
g. Attach the Label as shown.
% <G
+I
C
S
T
EL
EE
AB
L
T+
ER
T,
<
T+
G
,
I
,
AL
<T
T,
G
I
PA R A L L E L
W
AL
+,
T,
W
MOLDING
+,
Issue: C 02/07/12
e. Use Household Glass
Cleaner to clean the inside of
the Front Door Windows.
Page 19 of 22
<,>
Make sure to Align the
Label according to Etching or
Other Label.
REPEAT: steps e-g with the other
Window.
LEXUS
GS 350
2013–
CHECKLIST – these points MUST be checked to ensure a quality installation.
TVIP V4
REMOTE ENGINE STARTER (RES)
%A!^
Close the hood, enter the vehicle and close all doors. Place the shift lever in the “P” (Park) position, set the parking
brake and make sure the Vehicle is off.
"
(^A
1
Press the remote control’s lock button twice
within 2 seconds, then press and hold the
lock button for 3 seconds.
}!_=
The engine starts.
}!_%^
2
With the engine running, pull the hood
release handle.
The engine stops.
}!_
The security alarm triggers. (Only if equipped with
OE Factory Alarm, not Genuine Accessory alarm, and
only if armed)
<,>: Wait 30 seconds before pulling the
hood release handle for the Security Alarm
to trigger.
3
Move the shift lever out of “P” (Park).
Attempt to start the Vehicle using the
remote.
Issue: C 02/07/12
The engine does not start.
Page 20 of 22
LEXUS
GS 350
2013–
CHECKLIST – these points MUST be checked to ensure a quality installation.
TVIP V4
REMOTE ENGINE STARTER (RES)
A!^
A!
A!
>

Dome/Courtesy Lights
Horn

Steering Wheel Column Adjusts
Without Interference
Trunk Release Switch (if equipped)

Starter
Panel/Switch Illumination

Lamp Failure Sensor

Seat Belt Warning Light

Air Bag Warning Light

If the warning light remains on, it may
indicate a system malfunction.
If the warning light remains on, it may
indicate a system malfunction.

Gauges

ABS Light (if equipped)

Track/Skid Control Light (if equipped)

If the warning light remains on, it may
indicate a system malfunction.
If the warning light remains on, it may
indicate a system malfunction.
Tire Pressure Monitoring System
(TPMS)
Prior to TPMS activation and Pre-delivery
Service (PDS) of the Vehicle the TPMS light
will blink when IG is turned on.
If the warning light remains on, it may
indicate a system malfunction.
After TPMS activation and PDS of the Vehicle the TPMS light will illuminate for a few
seconds and go off when IG is turned on.
Cruise Control Light (if equipped)
;)Q^"4)6

Trunk/Tailgate/Bed Lights (if equipped)
Brake Lights
Backup Lights

Tail Lights
Daytime Running Lights (if equipped)
Marker Lights
Clearance Sonar (if equipped)
>)_`b,<6

Hazard Lights
Head Lights
High Beams
Power Side Mirrors (if equipped)
Power Sliding Door (if equipped)
Issue: C 02/07/12

Page 21 of 22
Turn Signal Lights
Fog Lights (if equipped)
Accessory Controls/Illumination (if equipped)
Convenience Memory Settings (if equipped)
Rear Sunshade (if equipped)
LEXUS
GS 350
2013–
CHECKLIST – these points MUST be checked to ensure a quality installation.
A!

TVIP V4
REMOTE ENGINE STARTER (RES)
A!
Front Wiper/Washer
Power Sun/Moon Roof (if equipped)
Clock (if equipped)
Audio/Video (if equipped)
Steering Wheel Audio Control (if equipped)
Front Windshield Defogger (if equipped)
Blind Spot Monitor (BSM) (if equipped)
Side Mirror Defogger (if equipped)
Massage Seats (if equipped)

Glove Box Light (if equipped)

Power Locks (if equipped)
Power Seats (if equipped)
Rear Wiper/Washer (if equipped)
Rollover Side Curtain Air Bag Switch (RSCA)
(if equipped)
Navigation System (if equipped)
USB Connections (if equipped)
Steering Wheel Heater (if equipped)
Rear Window Defogger (if equipped)
HVAC
Accessory Power Socket (if equipped)
Heated/Vented Seats (if equipped)
Passenger Air Bag Switch (if equipped)
Power Windows (if equipped)
Key Sensor Buzzer
Glass Breakage Sensor (GBS) (if equipped)
<,>
Remove the short pin after Function check. Check with your Port/Dealer to see if this step is necessary.
Issue: C 02/07/12
Page 22 of 22