SKID STEER LOADER ATTACHMENT DIRECTORY

SKID STEER LOADER
ATTACHMENT DIRECTORY
SK714-5 • SK815-5 • SK818-5 • SK820-5 • SK1020-5 • SK1026-5
INTRODUCTION
STATEMENT OF LIMITATION
This directory provides Komatsu Skid Steer
Loader distributors and customers with a listing
of single source, worksite application, attachments. These attachments are designed and
manufactured by some of the leading attachment
manufacturers for specific fit to our Skid Steer
Loaders. And since these attachments are sold
through Komatsu, they qualify for the same
finance programs offered on the base loaders.
The attachments listed in this directory have not
been designed, tested, or manufactured by
Komatsu and we assume no responsibility for
their performance. The attachment manufacturer
is solely responsible for any defects or failures,
personal injury or property damage caused by
the equipment or its use.
Customer satisfaction is our first priority. Before
choosing the attachment from this directory for a
specific application, you should consider:
1) The customer application and whether that
attachment is designed to perform this
application
2) Whether the attachment and machine are
sized appropriately for the customer’s
application and production requirements
3) Whether the attachment width is as wide or
wider than the machine width measured over
the tires
4) Whether all manufacturers’ recommendations
can be followed, including additional counterweights, guarding and protective devices
The attachment manufacturer listed on the
attachment page is the best source for verification of the above items. Therefore, we recommend that you contact them directly. Alternatively,
you can contact your Komatsu territory manager
who can, in turn, contact the manufacturer for
you.
The manufacturer-supplied warranty on these
attachments is equal to our warranty period on
the base machine. Please note that it is administered by these manufacturers along with parts
and service support. The manufacturer index on
page 39 provides contact information for each
attachment manufacturer.
All attachment information was supplied by the
attachment manufacturers and its accuracy was
not verified by Komatsu. The information is being
provided for the convenience of our dealers and
customers as a general depiction and description
of the attachment and its usage. The actual
attachment may vary from the information included in this directory. Please check with the manufacturer for the latest specifications.
Note: As used herein, "we", "us" or "our" refers
to Komatsu America Corp. and its parents, subsidiaries and affiliates.
Table of Contents
Worksite Application Choices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Auger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Backhoe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Backhoe - Mini . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Blade - Dozer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Boom - Material Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Breaker - Hydraulic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Broom - Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Broom - General Purpose Pick-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Brush Cutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Bucket - Brush Grapple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Bucket - Forked Scrap Grapple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Bucket - General Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Buckets - General Purpose Utility & Light Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Bucket - Heavy Duty Scrap Grapple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Bucket - Multi-Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Bucket - Rock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Cold Planer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Concrete Claw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Forks - Pallet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Grapple - Log Fork . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Hitch - Three Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Power Rake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Preparator® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Rock Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Roller - Vibratory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Scarifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Snow Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Snow Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Stump Grinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Tiller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Tracks - Over-the-Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35-36
Tree Spade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Trencher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Manufacturer Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
1
WORKSITE APPLICATION CHOICES
TYPICAL USAGE
Common
Attachment
Auger
Backhoe
Backhoe-Mini
Blade-Dozer
Boom-Material Handling
Breaker-Hydraulic
Broom-Angle
Broom-General Purpose Pick-Up
Brush Cutter
Bucket-Brush Grapple
Bucket-Forked Scrap Grapple
Bucket-General Purpose
Buckets-Utility/Light Material
Bucket-H.D. Scrap Grapple
Bucket-Multi-Purpose
Bucket-Rock
Cold Planer
Concrete Claw
Forks-Pallet
Grapple-Log Fork
Hitch-Three Point
Power Rake
Preparator
Rock Wheel
Roller-Vibratory
Scarifier
Snow Blade
Snow Blower
Stump Grinder
Tiller
Tracks-Over the Tire
Tree Spade
Trencher
Seldom
Landscape
Industrial
Construction
Note: Above application recommendations provided by the attachment manufacturers
2
Agriculture
Page No.
3-4
5-6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35-36
37
38
AUGER Woods Equipment Corporation
Power Augers: Dig holes up to 36" in diameter with
speed and accuracy. Mount design ensures the auger will
remain balanced in uneven work conditions.
• Large 1-1/2-inch plated pivot pins are
stronger than competitors’ models
and resist rust.
• Long-lasting standard auger bits are
alloy steel plated; optional cast alloy
bits also available.
• High-flow HA25 & HA30 planetary
models are designed for heavy
industrial use in hard soil to depths
up to 20 feet, depending on conditions.
• Standard-flow planetary model for
10-foot depths; chain drive units maximize productivity for digging to
5-foot depths.
• Manufactured by Woods Equipment
Corporation
Specifications
Attachment
Komatsu Model
HA15P
HA20
HA25
HA30
SK714, SK815, SK818, SK820
SK815, SK818, SK820 - HIGH FLOW
*
*
SK1020, SK1026
SK1020, SK1026 - HIGH FLOW
*
*
Dimensions
Drive Type
Planetary
Planetary
Planetary
Planetary
Flow Range
10 - 20 gpm
10 - 20 gpm
10 - 30 gpm
10 - 40 gpm
3500 psi
3500 psi
3500 psi
3500 psi
36"
36"
36"
36"
Approximate Weight
300 lb
600 lb
620 lb
650 lb
Performance Guide
Construction Grade
Construction Grade
Heavy Duty
Heavy Duty
Pressure Range
Maximum Bit Size
* For Low Flow Circuit
Continued on Next Page
3
AUGER Woods Equipment Company
Continued from Previous Page
BIT SPECIFICATIONS
Alloy Steel Plate Head • Bolt and Lug Dual-Angle Reversible Teeth • 2-9/16" round & 2" hex Hubs • Standard-Duty (double flight)
Size - Diameter x Length*
No. of Teeth
Approximate Weight
6"x50"
2
54 lb
9"x50"
4
78 lb
12"x50"
4
107 lb
15"x50"
5
117 lb
18"x50"
6
145 lb
24"x50"
8
215 lb
30"x48"
10
280 lb
35"x48"
12
385 lb
24"x50" tree
9
175 lb
30"x48" tree
11
240 lb
36"x48" tree
12
315 lb
* Extensions 12", 24", 48"
Heavy-Duty (double flight) bits also available
4
BACKHOE Attachment Technologies Inc.
The Backhoe has the best bucket digging force for a
four-bar linkage backhoe and the highest capacity buckets
in its class. The longest reach from the swing post offers
the ability to place material farther from the excavation
and allows for fewer moves. Increase versatility by adding
an optional 12" - 36" wide severe duty bucket with teeth,
a fixed or hydraulic knuckle thumb, or a dual acting auxiliary hydraulic kit.
• Dual-cylinder cushioned swing provides
maximum power where it is needed.
• Swing speed control standard
• Cushioned swing brings the backhoe to a
gentle stop at each end of the swing arc.
• High clearance swingpost allows operation where clearance is critical.
• Available with SAE or ISO control pattern.
• Fixed or hydraulic thumb option converts
backhoe into powerful loader
for landscaping, land clearing or demolition. Meshes with all 16" to
24" buckets.
• Optional two-way auxiliary flow
hydraulic kit runs hydraulic thumb, coupler, breaker or other hydraulic attachment.
• Skid steer rear stabilizer attachment
may improve performance.
• Optional vertical stabilizer available.
• Manufactured by ATI
Specifications
Attachment
509
511
609
611
Komatsu Model
SK714
SK815
*
*
SK818, SK820
*
*
*
*
SK1020, SK1026
*
*
*
*
Transport Height – A
7'9"
8'10"
7'9"
8'10"
Transport Width
5'0"
5'0"
4'9"
4'9"
Dimensions
Ground Clearance – B
11"
11"
11"
11"
Overall Length – C
7'7"
7'9"
7'7"
7'9"
Boom Pivot Height
16"
16"
16"
16"
1425 lb
1594 lb
1702 lb
1847 lb
Digging Depth Maximum – D
9'8"
11'1"
9'8"
11'1"
Digging Depth (2 ft.) Flat Bottom – E
9'7"
11'0"
9'7"
11'0"
Operating Weight w/12" Bucket
* For Low Flow Circuit
Continued on Next Page
5
BACKHOE Attachment Technologies Inc.
Continued from Previous Page
K
180°
G
J
60°
C
H
A
B
16"
17"
E
F
M
D
2'
Specifications
Attachment
Digging Depth (8 ft.) Flat Bottom – F
Continued
509
511
609
611
8'3"
9'11"
8'3"
9'11"
Overall Operating Height - Fully Raised – G
12'10"
14'5"
12'10"
14'5"
Loading Height – H
6'10"
8'0"
6'10"
8'0"
Loading Reach – J
4'2"
5'0"
4'2"
5'0"
Reach From Swing Post – K
12'9"
14'5"
12'10"
14'5"
Bucket Rotation – L
180°
180°
180°
180°
Swing Arc
180°
180°
180°
180°
Straight Wall Digging Depth – M
7'3"
8'2"
7'3"
8'2"
Stabilizer Spread Operating Position
7'11"
7'11"
9'11"
9'11"
16"
16"
17"
17"
2500 psi
2500 psi
2500 psi
2500 psi
Stabilizer Down Below Grade
System Relief Valve Setting
Digging Force - Bucket Cylinder
5676 lb
5676 lb
5908 lb
6167 lb
Digging Force - Dipper Cylinder
2754 lb
3056 lb
3232 lb
4160 lb
6
BACKHOE — MINI FFC Attachments
The Mini Backhoe has excellent mobility, and is perfect for digging footings.
• Easy mounting, no stabilizers required.
• 3x16 cylinder for powerful breakout
force.
• Fast and easy for trenches up to 5'6"
deep.
• Flat face O-ring seal couplers eliminate leaks.
• Manufactured by FFC
Specifications
Attachment
Komatsu Model
MB12
MB18
MB24
SK714
*
SK815, SK818, SK820, SK1020, SK1026
*
*
*
5'6"
5'6
5'6"
Dimensions
Digging Depth
Bucket Width
Weight
12"
18"
24"
635 lb
665 lb
695 lb
* For Low Flow Circuit
7
BLADE — DOZER Attachment Technologies Inc.
This Dozer Blade is designed specifically for
material handling with heavy-duty construction
with a round moldboard and a pre-drilled front
to accept a bolt-on edge.
• Available with standard skid shoe.
• Hydro-electric controlled angle and
tilt, using only one loader valve.
• Angle and tilt cylinders are interchangeable and equipped with selfaligning bushings.
• Reversible .75" x 8" bolt-on cutting
edge and rolled moldboard .31" thick
and 28" high.
• Blade angles 30° left or right and tilts
10° each way from horizontal.
• Tilt indicator visible from operator’s
seat.
• Flat face O-ring seal couplers
eliminate leaks.
• Manufactured by ATI
Specifications
Attachment
Komatsu Model
SK714
DB84
DB96
*
SK815, SK818, SK820, SK1020, SK1026
Dimensions
Width from Centerline to Inside Edge @ 15° Angle
43.53"
49.31"
Width from Centerline to Inside Edge @ 30° Angle
42.19"
47.38"
Dozer Blade Width @15° Angle
81.13"
92.73"
Dozer Blade Width @30° Angle
73.13"
83.56"
Width from Centerline to Outside Edge @ 15° Angle
37.63"
43.41"
Width from Centerline to Outside Edge @ 30° Angle
30.94"
36.16"
Overall Width
84.00"
96.00"
30°
30°
Overall Length
36.68"
36.68"
Overall Height
29.89"
29.89"
Approx. Weight
1365 lb
1460 lb
Angle Left and Right
* For Low Flow Circuit
8
BOOM — MATERIAL HANDLING
Attachment Technologies Inc.
The Material Handling Boom is the perfect
piece to complete your landscape tool inventory. Use it to set trees and move cut trees. Also,
this boom can handle moving attachments or
concrete forms around the job site.
• Pintle hitch standard.
• 1500 lb lift capacity.
• Skid steer rear counterweight attachment
recommended for some applications.
• Manufactured by ATI
Specifications
Attachment
Komatsu Model
SK714, SK815, SK818, SK820, SK1020, SK1026
MH66
Dimensions
Rated Load Capacity
Height
1500 lb
66"
9
BREAKER — HYDRAULIC
These low maintenance Hydraulic Breakers
from Komatsu have a high energy transmission
and are fully hydraulic in operation.
• Narrow shape for ease of work in confined areas.
• Extra long piston stroke.
• Reliable in-body accumulator.
• Replaceable tool bushing.
• Dual rectangular shaped tool retainers.
• Flat face O-ring seal couplers
eliminate leaks.
• Skid steer special application front
door attachment is recommended.
Specifications
Attachment
Komatsu Model
SK714, SK815, SK818, SK820
JPB200
JPB210
*
*
SK1020, SK1026
Dimensions
CIMA Tool Energy Rating
198 ft lb
212 ft lb
Flow Range
17 gpm
22 gpm
Striking Rate
1108 bpm
1375 bpm
1900 psi
2059 psi
440 lb
527 lb
Striking Rate (blows per minute)
740 min
1040 min
Adjusted Breaker Pressure
1750 psi
2000 psi
Max. Operating Pressure
1950 psi
2100 psi
2.5"
2.5"
Operating Pressure
Working Weight
Tool Diameter
* For Low Flow Circuit
10
BROOM — ANGLE Attachment Technologies Inc.
Angle Brooms are excellent for cleaning
and removing dirt, small rocks, snow and
other debris from parking lots, driveways,
streets, sidewalks and floors.
• Moves loose materials ahead and to
the side of the broom.
• Angles 30° left or right.
• Adjustable down force.
• Easily adjusted brush settings.
• Side shifts 10" off center (left or right).
• Heavy gauge side plates and shell.
• Inset hydraulic motor for motor protection and better obstacle clearance.
• Flat face O-ring seal couplers
eliminate hydraulic leaks.
• Poly/wire brush uses more wafers than
many competitors.
• Optional water kit with 25 gallon water
reservoir.
• Optional hydraulic angle kit.
• Manufactured by ATI
Specifications
Attachment
Komatsu Model
SK714, SK815
AB72
AB84
*
*
SK818, SK820, SK1020, SK1026
Dimensions
Overall Width
Sweeping Width
82"
94"
76"
88"
Overall Height
35.5"
35.5"
Length Coupler to Brush Front
59.60"
59.60"
Transport Height On Stand
40.0"
40.0"
30°
30°
Maximum Angle (Left and Right)
Sweeping Width @ 30° Angle
66"
76"
972 lb
1031 lb
Brush Diameter
32"
32"
Wafers (Quantity)
38
45
Weight
* For Low Flow Circuit
11
BROOM — GENERAL PURPOSE PICK-UP
Woods Equipment Corporation
The General Purpose Pick-Up Broom is
excellent for sweeping and scraping dirt,
small rocks and other debris from parking
lots, driveways, streets, sidewalks and
depositing debris in the bucket. Reduces
spillage and airborne contaminants.
• Forward and reverse sweeping
directions provide greatest versatility.
• Bolt-on cutting edge scrapes hard
packed mud before sweeping.
• Heavy gauge side-plate and shelf.
• Optional gutter broom allows for closer
sweeping next to curbs and other
vertical surfaces.
• Flat face O-ring seal couplers
eliminate leaks.
• Sweeps and deposits materials into
the bucket for easy removal and
dumping.
• Manufactured by Woods Equipment
Corporation
Specifications
Attachment
Komatsu Model
PB68
SK714, SK815, SK818, SK820, SK1020
SK815, SK818, SK820, SK1020, SK1026 - HIGH FLOW
*
Dimensions
Brush Width
60"
Overall Width
68.5"
Height
25.25"
Length
67.7"
Approximate Weight
Hopper Capacity
* For Low Flow Circuit
12
714 lb
13.5 cu. ft.
BRUSH CUTTER FFC Attachments
Brush Cutter cuts undergrowth and brush
while mulching with an added feature of a
stump jumper.
• 1/4" deck thickness.
• High speed one direction blade with a
cutting capacity of 3".
• Automatic hydraulic blade shut-off, no
hold down chains or cables to contend
with.
• One direction lift.
• Front chain guard/rear roller with
tapered roller bearings.
• Single motor hydraulic drive.
• Optional front caster wheels.
• Manufactured by FFC
Specifications
Attachment
Komatsu Model
SK714, SK815
LAF3748
LAF3760
LAF3772
SK818, SK820
SK1020, SK1026
Dimensions
Overall Width
51.5"
63.5"
75.5"
Cutting Width
48"
60"
72"
Height
27"
27"
27"
15-30 gpm
15-30 gpm
15-30 gpm
3500 psi
3500 psi
3500 psi
8316/12751 ft/min
10395/15939 ft/min
12474/19127 ft/min
1324 lb
1464 lb
1653 lb
GPM range
Max PSI range
Blade Speed Min/Max
Weight, Approx.
13
BUCKET — BRUSH GRAPPLE
Attachment Technologies Inc.
Brush Grapple Buckets performs many jobs in
one. In a single pass, rake away debris, keep it in a
manageable pile, move it around with ease, or use
it to backfill. Load or pile logs, brush, rocks, demolition debris, and many other types of materials.
• Dual independent see-through grapples.
• Helix tooth design to aid in pulling the
work into the bucket.
• Complete protection for cylinders (top,
bottom and outboard sides).
• Double pilot-operated check valve for
locking grapple into position.
• Hydraulic hose protection and seclusion
(hoses route immediately into top cross
tubing).
• Pivot pins have lubrication capabilities.
• Flat face O-ring seal couplers eliminate
leaks.
• Skid steer rear counterweight attachment
recommended for some applications.
• Manufactured by ATI
Specifications
Attachment
Komatsu Model
BG72
SK714
*
SK815, SK818, SK820
*
BG84
*
*
SK1020, SK1026
Dimensions
Overall Width
72"
84"
Overall Depth
35.9"
35.9"
Grapple Width
20.5"
20.5"
Tine Spacing
6"
6"
Grapple Height - Closed
26.4"
26.4"
Grapple Hook - Opening
42"
42"
Overall Weight (lbs)
794 lb
826 lb
Clamping Force (lbs)
1250 lb
1250 lb
Number of Grapple Teeth
4
4
Number of Cylinders
2
2
Tines & End Plates
1/2" T1 Steel (100,000 lb yield)
1/2" T1 Steel (100,000 lb yield)
Bore
2.00"
2.00"
Stroke
8.25"
8.25"
Rod Diameter
1.25"
1.25"
* For Low Flow Circuit
14
BUCKET — FORKED SCRAP GRAPPLE
FFC Attachments
The Forked Scrap Grapple Bucket is great
for brush and refuse removal. In addition to
enclosed cylinders, our grapple bucket also
offers enclosed hoses for added protection on
the job site.
• Load loose material while leaving dirt
behind.
• Grapples work independently to handle uneven loads.
• Heat-treated tines.
• Cylinder guard standard.
• Flat face O-ring seal couplers
eliminate leaks.
• Skid steer rear counterweight attachment recommended for some applications.
• Manufactured by FFC
Specifications
Attachment
Komatsu Model
FSG63
FSG72
SK714
SK815, SK818, SK820, SK1020, SK1026
*
*
Opening Height
41"
41"
Height Closed
20"
20"
Usable Tooth
24.13"
24.13"
Width
63.44"
73.06"
Dimensions
Number of Teeth
8
10
990 lb
1100 lb
Cylinder Bore
2"
2"
Cylinder Stroke
8"
8"
Approximate Weight
* For Low Flow Circuit
15
BUCKET — GENERAL PURPOSE
Woods Equipment Corporation
General Purpose Bucket is ideal for medium to
heavy load and carry, general construction and
excavating type work. Choose between the long or
short-lip design. The long-lip design provides
increased visibility and maximum capacity while the
short lip design provides maximum breakout force.
• The heavy-duty construction utilizes
no internal gussets or obstructions.
• Round design moldboard offers maximum loading and unloading capabilities with higher capacities for light
material handling applications.
• The square back profile allows for
reverse grading.
• A pre-drilled front edge will accept a
bolt-on edge.
• Available with welded Hensley tooth
adapters.
• Bucket with factory-installed bolt-on
edge available.
th
wid
• Skid steer rear counterweight attachment recommended for some applications.
• Manufactured by Woods Equipment
Corporation
Toothbar Option
Specifications
Attachment
Komatsu Model
GP61S
GP68S
GP61L
GP68L
SK714-5
SK815-5, SK818, SK820
Short
Short
Short
Long
Long
Long
Width
61"
68"
73"
61"
68"
73"
Height
19"
Length
29"
19"
19"
19"
19"
19"
29"
29"
35"
35"
35"
Approximate Weight
404 lb
440 lb
469 lb
439 lb
475 lb
508 lb
Heaped Capacity
11 cu ft
13.4 cu ft
14.4 cu ft
14.8 cu ft
16.5 cu ft
17.8 cu ft
Optional Teeth
weld-on
weld-on
weld-on
weld-on
weld-on
weld-on
SK1020, SK1026
GP73S
GP73L
Dimensions
Type of Bottom
Optional Bolt-on Cutting Edge 5/8" x 8" reversible 5/8" x 8" reversible 5/8" x 8" reversible 5/8" x 8" reversible 5/8" x 8" reversible 5/8" x 8" reversible
Optional Bolt-on Toothbar
Inside Bucket Width
16
59-3/8" - 59-3/4" 66-3/8"- 66-3/4" 71-3/8"- 71-3/4"
59-3/8"- 59-3/4" 66-3/8"- 66-3/4" 71-3/8"- 71-3/4"
BUCKETS — GENERAL PURPOSE UTILITY & LIGHT MATERIAL
Woods Equipment Corporation
General Purpose Utility Buckets are ideal for
light to medium material load and carry operations. The Light Material Buckets are primarily
for low density material such as woodchips,
mulch, fertilizer, snow and other light aggregate.
• Heavy-duty construction utilizes no
internal gussets or obstructions.
• Round design moldboard offers maximum loading and unloading capabilities and higher capacities for light
material handling applications.
• The square back profile allows for
reverse grading.
• A pre-drilled front edge will accept a
bolt-on edge.
• Bucket with factory-installed bolt-on
edge available.
• Bucket with welded Hensley tooth
adapters available (utility only).
width
• Skid steer rear counterweight attachment recommended for some applications.
• Manufactured by Woods Equipment
Corporation
Toothbar Option
Specifications
Attachment
Komatsu Model
UT66
UT72
LM66
LM72
LM78
SK714-5
SK815-5, SK818, SK820
SK1020, SK1026
LM84
Dimensions
Type
GPU
GPU
LM
LM
LM
LM
Width
66"
72"
66"
72"
78"
84"
Height
25"
25"
26"
26"
26"
26"
Length
35"
35"
38"
38"
38"
38"
513 lb
553 lb
543 lb
585 lb
617 lb
660 lb
Heaped Capacity
20.8 cu ft
22.8 cu ft
23.5 cu ft
25.8 cu ft
28.1 cu ft
30.3 cu ft
Optional Bolt-on Cutting Edge
5/8" x 8"
reversible
5/8" x 8"
reversible
5/8" x 8"
reversible
5/8" x 8"
reversible
5/8" x 8"
reversible
5/8" x 8"
reversible
64-3/8"64-3/4"
70-3/8"70-3/4"
not
recommended
not
recommended
not
recommended
not
recommended
Approximate Weight
Optional Bolt-on Toothbar
Inside Bucket Width
17
BUCKET — HEAVY DUTY SCRAP GRAPPLE
Woods Equipment Corporation
Heavy Duty Scrap Grapple Buckets are
designed to handle oddly-shaped objects such
as railroad ties, trees, rocks, debris, and other
demolition scrap.
• High strength design provides for
longer service life.
• Double grapples maximize load handling capabilities.
• Pre-drilled front edge will accept a
bolt-on edge.
• Flat face O-ring seal couplers eliminate leaks.
• Available with factory-installed bolton edge.
• Skid steer rear counterweight attachment recommended for some applications.
• Manufactured by Woods Equipment
Corporation
Specifications
Attachment
Komatsu Model
SG66
SK714
SK815, SK818, SK820 - HIGH FLOW
*
SG72
SG78
*
SK1020
SK1020, SK1026 - HIGH FLOW
*
*
72"
78"
Dimensions
Width
66"
Height
28"
28"
28"
Length
27-1/4"
27-1/4"
27-1/4"
12.9 cu ft
14 cu ft
15.2 cu ft
826 lb
856 lb
886 lb
Capacity
Approximate Weight
Cylinder Bore Diameter
Cylinder Stroke
Optional Bolt-on Cutting Edge
* For Low Flow Circuit
18
2"
2"
2"
8-1/4"
8-1/4"
8-1/4"
5/8" x 8" reversible
5/8" x 8" reversible
5/8" x 8" reversible
BUCKET — MULTI-PURPOSE
Woods Equipment Corporation
The Multi-Purpose Bucket is a versatile, multiple use
tool for grading, dozing, clamping, loading, high dumping,
and scraping. Like having four attachments in one. Its
heavy-duty construction and industrial strength cylinders
and cutting edges provide a long life for landscaping,
municipal, construction or demolition jobs.
• A bolt-on replaceable dozer edge is
standard.
• A pre-drilled front edge will accept a
bolt-on edge.
• Flat face O-ring seal coupler eliminates leaks.
• Bucket with factory-installed bolt-on
cutting edge available.
• Bucket with welded Fabco crimp-on
tooth adapters available.
wi
dth
• Skid steer rear counterweight attachment recommended for some applications.
Toothbar Option
• Manufactured by Woods Equipment
Corporation
Specifications
Attachment
Komatsu Model
SK714
MP60
MP66
MP73
SK815, SK818, SK820
SK815, SK818, SK820 - HIGH FLOW
*
*
MP78
SK1020, SK1026
SK1020, SK1026 - HIGH FLOW
*
*
Dimensions
Width
60"
66"
73"
78"
Height
31"
31"
31"
31"
Length
33"
33"
33"
33"
Heaped Capacity
11.5 cu ft
12.8 cu ft
14.2 cu ft
15.5 cu ft
Approximate Weight
529 lb
582 lb
644 lb
688 lb
Cylinder Rod Diameter
1-1/2"
1-1/2"
1-1/2"
1-1/2"
Cylinder Bore
2-1/2"
2-1/2"
2-1/2"
2-1/2"
Cylinder Stroke
Optional Bolt-on Reversible Cutting Edge
Optional Bolt-on Toothbar
Inside Bucket Width
8"
8"
8"
8"
5/8" x 8" reversible
5/8" x 8" reversible
5/8" x 8" reversible
5/8" x 8" reversible
64-3/8"- 64-3/4"
71-3/8"- 71-3/4"
58-3/8"- 58-3/4"
76-3/8"- 76-3/4"
* For Low Flow Circuit
19
BUCKET — ROCK Attachment Technologies Inc.
Rock Buckets are designed to rake, pile
and load debris from construction sites,
pastures, fields and other areas.
• Cradles the collected rocks and debris
while additional material is being collected.
• Tine spacing determines the size of
the rocks and debris that will be
retained while allowing the soil to sift
back to the ground.
• The rake design is used to gather
material away from buildings and
obstructions, for faster clean up of
debris, to level out clumps of dirt and
to pick up pieces of sod.
• Manufactured by ATI
Specifications
Attachment
Komatsu Model
SK714
RB66
RB75
*
*
SK815, SK818, SK820, SK1020, SK1026
Dimensions
Overall Width
65.85"
74.35"
Overall Depth
42.45"
42.45"
Depth with Skid-Steer Mounting
49.80"
49.80"
Overall Height
21.77"
21.77"
Tine Spacing (Center to Center)
4.25"
4.25"
Tine Spacing (Between Tines)
3.125"
3.125"
Overall Weight (lbs)
550 lb
619 lb
16
18
1.125"
1.125"
Number of Tines
Tine Rod Diameter
20
COLD PLANER Woods Equipment Corporation
• Top pivot design self levels the drum and
chassis creating higher downforces, precise depth control and easier operation.
Cold Planers are used for concrete and
asphalt road repair, opening trenches for utility work, milling bridge decks and removing
cracks and bumps.
• Wheels on the drum chassis minimize
the changes of gouging the asphalt.
• Side skids reduce the possibility of the
wheels dropping into the cut when
milling potholes or making butt joints.
• Cutting drum is driven through a planetary gearbox.
• Electrohydraulic tilt depth and sideshift
control eliminate difficult manual adjustments and is standard on all models.
• Hinged top cover permits easy access
for pick maintenance.
• Chassis design allows drum installation
or removal in 60 minutes or less.
• Flat face O-ring seal couplers eliminate
leaks.
• Skid steer rear counterweight attachment recommended for some applications.
• Manufactured by Woods Equipment
Corporation
Specifications
Attachment
Komatsu Model
CP16
CP18
CP24
SK815, SK818, SK820 - HIGH FLOW
SK1020, SK1026 - HIGH FLOW
SK714, SK815, SK818, SK820, SK1020, SK1026
CP12
CP30
Dimensions
Depth of Cut
0-6"
0-6"
0-6"
0-6"
0-6"
Width of Cut
12"
16"
18"
24"
30"
Number of Teeth
28
50
56
70
77
Sideshift
22"
22"
22"
22"
22"
Tilt
19°
19°
19°
15°
11°
1200 lb
1750 lb
2000 lb
2300 lb
2450 lb
Hydraulic Depth Control
STD
STD
STD
STD
STD
Hydraulic Tilt Control
STD
STD
STD
STD
STD
Weight
21
CONCRETE CLAW FFC Attachments
Concrete Claw removes concrete on sidewalks, driveways or any construction sites.
• Replaceable points.
• End plates and tooth shanks are made
with high strength T-1 steel.
• 1" x 8" wear resistant Pacal steel
tapered cutting edge.
• Features name-brand replaceable
points with 1-1/2" wide shanks.
• Rubberized flex pins securely fasten
replaceable points.
• Manufactured by FFC
Specifications
Attachment
Komatsu Model
SK714, SK815, SK818, SK820, SK1020, SK1026
10024
Dimensions
Working Width
24"
Working Depth
48"
Height OD
21"
Rear Opening Height
7.5"
Weight, Approx.
22
575 lb
FORKS — PALLET Attachment Technologies Inc.
Pallet Forks are designed and constructed
specifically for heavy duty applications. This
essential tool easily transports bulky, baled or
palletized materials.
• Rail type, double lock down provides
protection from load shifting.
• Certified forged teeth increase
strength and service life.
• Backguard allows for greater operator
visibility.
• Skid steer rear counterweight attachment recommended for some applications.
• Manufactured by ATI
Specifications
Attachment
Komatsu Model
SK714, SK815, SK818, SK820, SK1020, SK1026
PF48
*
Dimensions
Weight (including mounting)
Fork Length
Fork Capacity
Fork Spread Range
370 lb
48"
4000 lb
4-3/8 - 40-3/8"
High Visibility Back Guard
yes
Tooth Double Lock Downs
yes
23
GRAPPLE — LOG FORK
FFC Attachments
The Log Fork Grapple is an excellent
attachment for handling logs, pipes, brush,
and other bulky materials.
• 2" x 8" hydraulic cylinder.
• Closes to 6" log or pipe.
• Flat face O-ring seal couplers eliminate leaks.
• Skid steer rear counterweight attachment recommended for some applications.
• Manufactured by FFC
Specifications
Attachment
Komatsu Model
LG28
SK714, SK815, SK818, SK820, SK1020, SK1026
SK815, SK818, SK820, SK1020, SK1026 - HIGH FLOW
*
Dimensions
Tine Length
28.4"
Opening Height
43.1"
Capacity
6400 lb
Weight
610 lb
* For Low Flow Circuit
24
HITCH — THREE POINT
Woods Equipment Corporation
A Three Point Hitch is necessary for adapting
certain attachments to Komatsu skid steer
loaders.
• Adapts 3 point hitch, category 1
attachments to skid steer loaders.
• Landscape rakes, box scrapers, pulverizers and more are skid steer
loader compatible.
• Manufactured by Woods Equipment
Corporation
Specifications
Attachment
Komatsu Model
SK714, SK815, SK818, SK820, SK1020, SK1026
TH3000
Dimensions
Overall Width
46"
Height
26"
Length
11"
Approximate Weight
180 lb
25
POWER RAKE FFC Attachments
Power Rakes efficiently handle the toughest landscape tasks - finish grading, pulverizing, debris
removal, spreading soil or filling, and de-thatching.
All-purpose versatile grading and cleaning tool. It is
designed to facilitate lawn de-thatching, seedbed
preparation, turf removal, and highway shoulder
reclamation. Pulverize dirt clods while keeping rocks
and debris ahead of the rolling action. Produce perfect beds for sodding, seeding, and much more.
• Bi-directional drum works soil forward
and backwards, removing rocks and
debris, preparing soil for sod or seed.
• Dual motor design delivers more
power for faster cycles.
• Heavy-duty carbide teeth.
• Direct drive motor reduces maintenance.
• Heavy-duty frame extends life.
• Low height improves visibility.
• Available with manual or hydraulic
angling of 20 degrees.
• Manufactured by FFC
Specifications
Attachment
Komatsu Model
SK714, SK815, SK818, SK820
PRA72
PRR72
*
*
SK1020, SK1026
PRA90
PRR90
*
*
Dimensions
Working Width
72"
72"
90"
90"
Overall Width
83"
83"
101"
101"
Fully Angled Width
68"
NA
86"
NA
Height
30"
30"
30.3"
30.3"
Manual / Hydraulic
NA
Manual / Hydraulic
NA
1000 lb
850 lb
1075 lb
925 lb
Angle Option
Weight
* For Low Flow Circuit
26
PREPARATOR
®
The Preparator attacks the toughest ground
condition, collects rocks and debris from 1"
to 20" in diameter, and tills compacted soil to
create a perfect seedbed. The adjustable
rolling drum conditions the soil and carries
debris into its perforated bucket.
FFC Attachments
• Short couple design allows good visibility of the surrounding worksite.
• Rotating drum carries rocks and debris
into its bucket while leaving the soil
ready to be planted. Perforated bucket
floor allows dirt to sift through.
• Powerful rotating drum conditions soil
with the scarifying action of A-R 400
steel teeth.
• Heavy-duty drum is designed to withstand the abuse of rocky working conditions.
• Variable speed motor and bi-directional
drum capable of tilling and fluffing the
soil as well as raking and grooming.
• Floating-head design allows it to follow
ground contours while picking up
rocks from 1" to 20" in diameter for
virtually debris-free soil preparation.
• Spring tines work to eliminate skid
shoe tracks.
• Manufactured by FFC
Specifications
Attachment
Komatsu Model
P54
SK714
*
P66
P76
*
SK815, SK818, SK820
*
SK1020, SK1026
Dimensions
Bucket Capacity
Overall Width
8.86 cu ft
10.32 cu ft
12.5 cu ft
63.75"
75.25"
85.25"
Bucket Swath Width
54"
66"
76"
Overall Bucket Height
25.53"
25.53"
25.53"
Overall Bucket Length
53"
53"
53"
RPM-r/min @ 16 gpm Nominal Flow
0-100
0-100
0-100
Overall Drum Diameter
21.5"
21.5"
21.5"
Tooth Thickness
.19"
.19"
.19"
Tooth Length
2.19"
2.19"
2.19"
250
300
340
Rake Drive
#80H Roller Chain
#80H Roller Chain
#80H Roller Chain
Brush Drive
#50H Roller Chain
#50H Roller Chain
#50H Roller Chain
976 lb
1270 lb
1465 lb
Number of Teeth
Overall Weight
* For Low Flow Circuit
27
ROCK WHEEL Woods Equipment Corporation
The Rock Wheel is ideal to cut utility lines
for gas, sewer, water, electrical, cable installation and repairs. Other applications include
asphalt patch cuts and creating expansion
joints in roadways.
• Gauge skid sets cutting depths and
minimizes extra passes for more precise control.
• Electro-hydraulic side shift allows
rockwheel to move from the center to
the operator’s right for placement of
the cutting wheel at the desired position.
• Planetary wheel drive reduction generates higher torque for fast asphalt
patch or roadway expansion joint
cuts.
• Optional 20 or 50 gal. water kit.
• Skid steer rear counterweight attachment recommended for some applications.
• Manufactured by Woods Equipment
Corporation
Specifications
Attachment
Komatsu Model
RW12
RW18
SK815, SK818, SK820 - HIGH FLOW
SK1020, SK1026 - HIGH FLOW
RW24
Dimensions
Depth of Cut
0-12"
0-18"
0-24"
Width of Cut
2.5/4.5"
2.5/4.5"
2.5/4.5"
28/33
42/44
56/66
22"
22"
22"
Weight
1600 lb
1800 lb
2100 lb
Wheel Speed
60 rpm
60 rpm
60 rpm
Cutting Speed
up to 15 fpm
up to 15 fpm
up to 15 fpm
Number of Teeth
Side Shift
28
ROLLER — VIBRATORY
Woods Equipment Corporation
Smooth drum Vibratory Rollers are used for compaction of granular material such as sand, gravel and
stone prior to asphalt or concrete curbing. Padded drum
vibratory rollers are used for compacting clay material.
• Easily maneuvered in tight spaces
where larger units will not fit; ideal for
smaller compaction jobs, near foundations and foliage.
• Half the cost of self-propelled, walkbehind, or ride-on models; self lubricating bearings reduce maintenance.
• Drum and shaft bearings lubricated in
oil bath; isolators on roller eliminate
vibration in cab.
• Padded sheepsfoot drum penetrates
heavy soils for effective compaction of
cohesive and clay materials.
• Low flow hydraulic design allows full
roller function and maximum compaction at only 15 gpm.
• Manufactured by Woods Equipment
Corporation
Specifications
Attachment
Komatsu Model
VR48A
VR66A
SK714, SK815, SK818, SK820
SK815, SK818, SK820 - HIGH FLOW
*
*
VR73A
SK1020, SK1026
SK1020, SK1026 - HIGH FLOW
*
*
Dimensions
Drum Width
48"
66"
73"
Overall Width
55.5"
73"
80.5"
Drum Oscillation
±15°
±15°
±15°
Overall Height
27"
27"
27"
Overall Length
33"
33"
33"
Drum Diameter
24"
24"
24"
7140 lb
8740 lb
10,240 lb
Total Output
Frequency VPM
2000 @ 15 gpm
2000 @ 15 gpm
2000 @ 15 gpm
Weight lbs. Smooth
1450 lb
1633 lb
1762 lb
Weight lbs. Padded
1600 lb
1850 lb
2100 lb
* For Low Flow Circuit
29
SCARIFIER Woods Equipment Corporation
Scarifier is ideal for loosening hard-packed
soil for landscape preparation or loosening
asphalt prior to removal.
• Built rugged for tough, heavy-duty
applications
• Manufactured by Woods Equipment
Corporation
Specifications
Attachment
Komatsu Model
SK714, SK815, SK818, SK820, SK1020, SK1026
SF3000
Dimensions
Working Width
40"
Overall Width
63"
Height
27"
Length
20"
Approximate Weight
350 lb
Number of Shanks
5
30
SNOW BLADE FFC Attachments
Snow Blades are designed for moving snow
or light dirt quickly.
• Hydraulic angle 30° max. in either
direction.
• Reversible and replaceable wear
edge.
• Adjustable skid shoes.
• Spring loaded trip mechanism.
• 7 gauge steel blade.
• Heavy structural steel frame.
• Manufactured by FFC
Specifications
Attachment
Komatsu Model
SB72
SK714
SK815, SK818, SK820
SB84
SB96
SK1020, SK1026
Dimensions
Length
72"
84"
96"
Height with Edge
23.25"
23.25"
23.25"
Angled Width
62.1"
72.5"
82.9"
Weight
475 lb
500 lb
525 lb
* For Low Flow Circuit
31
SNOW BLOWER FFC Attachments
This Snow Blower, with a two-stage
hydraulic blower, throws snow up to 35'.
Spout will rotate 280 degrees.
• Electronically-controlled, poly-lined
chute and deflector.
• High volume shroud opening.
• Excellent visibility.
• Wear-resistant Pacal steel tapered
wear edge, 3/8"x3".
• 12 gauge reinforced wrapper.
• Adjustable skid shoes.
• Manufactured by FFC
Specifications
Attachment
Komatsu Model
60
72
SK714
SK815, SK818, SK820
SK815, SK818, SK820 - HIGH FLOW
*
*
72H
84
84H
*
SK1020, SK1026
SK1020, SK1026 - HIGH FLOW
Dimensions
Cutting Width
60"
71.5"
72"
84"
84"
Shroud Opening
24.5"
24.5"
36"
25"
36"
Overall Depth
35.7"
35.5"
43"
38"
43"
Overall Height
56.75"
56.75"
74"
56.75"
74"
Weight
650 lb
685 lb
1150 lb
720 lb
1230 lb
* For Low Flow Circuit
32
STUMP GRINDER Woods Equipment Corporation
• Hydraulic controls manage swing, depth
and extension for easy operation in
tight areas.
Stump Grinders for stump grinding in residential, commercial, and agricultural areas. Grinding
arm swings a full 140° / 60 inches to level large
diameter trees; telescopes 7 inches to minimize
repositioning of the skid steer.
• Higher productivity via 16-inch cutting
depth and quick-attach bracket.
• More cost effective than tow-behind
models, no engine, belts, or tires to
maintain.
• More maneuverable than tow-behind
models; goes into areas not accessible
by truck.
• 3.25 inches wide cutting head with carbide teeth, levels stumps in minutes.
• Flat face O-ring seal couplers eliminate
leaks
• Skid steer special application front door
attachment is recommended.
• Manufactured by Woods Equipment
Corporation
Specifications
Attachment
Komatsu Model
SG20
SK714, SK815, SK818, SK820
SK815, SK818, SK820 - HIGH FLOW
*
SK1020, SK1026
SG40
SG60
*
64.1"
64.1"
64.1"
Telescopic Extension
7"
7"
7"
Horsepower Delivered
SK1020, SK1026 - HIGH FLOW
Dimensions
Overall Length
To 20 HP
To 40 HP
To 60 HP
Cutting Height Above Ground
21"
21"
21"
Cutting Depth Below Ground
16"
16"
16"
3.25"
3.25"
3.25"
Cutting Wheel Width
Cutting Width
60"
60"
60"
Swing Range
140°
140°
140°
Type of Teeth
0.5" slanted, carbide tip
0.5" slanted, carbide tip
0.5" slanted, carbide tip
Number of Teeth
32
32
32
Wheel Diameter
18"
18"
18"
700 rpm
900 rpm
900 rpm
765 lb
775 lb
840 lb
Wheel Speed (Approx..)
Weight
* For Low Flow Circuit
33
TILLER Woods Equipment Corporation
Tillers are used for mixing soils to improve seed beds
and stabilize soil. Other applications include tilling
construction sites and homesites prior to landscaping.
Bi-directional tine rotation allows unit to operate at
maximum effectiveness with loader moving forward or
backward.
• Dual direct drive motor design eliminates
the need for sprockets and chains and
the required lubrication of these components.
• Offset mounting configuration allows
right loader tracks to be covered when
operated in reverse for finish tilling operations.
• Drive motors are recessed in the chassis
which allows unit to be operated near
obstacles such as fences or buildings.
• Hardened, replaceable tines engineered
for extended life and easy replacement.
• Flat face O-ring seal couplers eliminate
leaks
• Manufactured by Woods Equipment
Corporation
Specifications
Attachment
Komatsu Model
TL52
SK714, SK815, SK818, SK820
SK815, SK818, SK820 - HIGH FLOW
*
TL73
TL84
SK1020, SK1026
SK1020, SK1026 - HIGH FLOW
*
Dimensions
Overall Width
60"
86"
97"
Cutting Width
52"
73"
84"
Working Depth
6"
6"
6"
Overall Height
31"
31"
31"
Number of Tines
28
36
40
Bi-directional
Bi-directional
Bi-directional
Tine Rotation
Weight
Driveline
Maximum Tine Speed
Max Flow
* For Low Flow Circuit
34
760 lb
1050 lb
1228 lb
(2) In-line gerotor motors
(2) In-line gerotor motors
(2) In-line gerotor motors
121 rpm
121 rpm
121 rpm
15 gpm @ 2000 psi
25 gpm @ 2000 psi
46 gpm @ 3500 psi
TRACKS — OVER-THE-TIRE Grouser Products
Over-The-Tire Tracks can be installed and removed
easily and efficiently for improved traction, tire strength
and protection on Komatsu Skid Steer Loaders in soft,
muddy, sandy or abrasive conditions.
• Reduces ground pressure by as much
as 50%.
• 1-1/4" hardened replaceable bushings.
• Run loose design to prevent strain on
loader drive system.
Cross Bar
Track
• Built-in length adjustment.
• Self-cleaning.
• Adds counterweight.
• Replaceable components.
• Open bar design provides maximum
traction and flotation.
Hard Shoe
Track
• Open side plate provides excellent
cleaning in the pivot areas.
• Field serviceable and rebuildable.
Soft Shoe
Track
• Manufactured by Grouser Products
Specifications
Komatsu Model SK714-5
Track Type
Track Width
Part Weight
Wheel Base
Standard Tires
Cross-Bar
13.25"
861 lb
37.4"
10.00 x 16.5
Wide Tires **
Cross-Bar
17.50"
974 lb
37.4"
31 x 15.5-15
37.4"
10.00 x 16.5
(4) Wheel Spacers for Wide Tires
Standard Tires
Hard Shoe
Standard Tires
Soft Shoe
Komatsu Model SK815-5 thru SK820-5 Track Type
13.25"
Tire Size
75 lb
1016 lb
13.25"
924 lb
37.4"
10.00 x 16.5
Track Width
Part Weight
Wheel Base
Tire Size
Standard Tires
Cross-Bar
13.25"
911 lb
41.3"
10.00 x 16.5
Wide Tires***
Cross-Bar
17.50"
1031 lb
41.3"
31 x 15.5-15
(4) Wheel Spacers for Wide Tires
75 lb
Standard Tires
Hard Shoe
13.25"
1058 lb
41.3"
10.00 x 16.5
Standard Tires
Soft Shoe
13.25"
962 lb
41.3"
10.00 x 16.5
Continued on Next Page
35
TRACKS — OVER-THE-TIRE
Grouser Products
Komatsu Model SK1020-5, SK1026
Continued from Previous Page
Track Type
Track Width
Part Weight
Wheel Base
Tire Size
Standard Tires
Cross-Bar
14.75"
1018 lb
45.8"
12.00 x 16.5
Standard Tires
Hard Shoe
14.75"
1335 lb
45.8"
12.00 x 16.5
Standard Tires
Soft Shoe
14.75"
1284 lb
45.8"
12.00 x 16.5
APPLICATION CHART
Cross-Bar Track
Hard Shoe Track
Soft Shoe Track
Soft and Muddy
Job Site Conditions
—
Muddy and Sandy
Job Site Conditions
—
Concrete or Asphalt
Job Site Surfaces
—
—
Rocky, Gravel or Abrasive
Job Site Conditions
—
36
TREE SPADE FFC Attachments
A Tree Spade can be used in planting, moving or transplanting trees and shrubbery.
Other uses include placing large decorative
rocks and stones.
• Completely transplant trees and
shrubbery.
• Dig holes for incoming trees.
• Transplant pre-packaged trees.
• Place trees in new location.
• Easier to position plants.
• 3/8" plate with sharp, tapered edge.
• Place large decorative rocks and
stones.
• Skid steer rear counterweight attachment recommended for some applications.
• Manufactured by FFC
Specifications
Attachment
Komatsu Model
TS36
TS40
TS42
TS44
SK714-5
SK815-5, SK818-5, SK820, SK1020, SK1026
TS48
Dimensions
Maximum Ball Size
Weight
36"
40"
42"
44"
48"
258 lb
312 lb
360 lb
378 lb
425 lb
37
TRENCHER Attachment Technologies Inc.
Trenchers are ideal for all types of utility and footer
trenches. High torque hydraulic motor for maximum
digging power.
• 2" pitch, anti-back flex chain for maximum performance and life.
• Double standard chain for tooth pattern
versatility.
• Heavy-duty chain reduction drive system amplifies torque to cutting chain.
• Sealed idler bearing is maintenance
free.
• Low profile dirt shield for better operator visibility.
• Built-in skid shoe to provide positive
depth control for auger.
• Pivoting crumber shoe and bar to assist
with loose soil removal.
• Bolt-on replaceable wear strips on
boom extends boom life under rough
conditions.
• Manufactured by ATI
Specifications
Attachment
SK714
615
*
625
650C
**
SK714, SK815, SK818, SK820, SK1020, SK1026
*
SK815, SK818, SK820, SK1020, SK1026 - HIGH FLOW
*
Dimensions
Boom Size
36"
36"
30"
36"
48"
30"
36"
48"
60"
Trench Depth @ Recommended Angle
36"
36"
30"
36"
48"
30"
36"
48"
60"
Chain Widths Available
6"
6"
6", 8"
6"
Recommended Trenching Angle
65°
65°
65°
65°
6", 8", 10", 12" 6", 8", 10", 12"
65°
65°
6", 8"
65°
6", 8", 10", 12" 6", 8", 10", 12"
65°
65°
Length
65"
65"
66"
73"
86"
58"
71"
84"
97"
Width
42"
50.5"
53"
53"
53"
43"
43"
43"
43"
Height
28"
28"
32"
32"
32"
37"
37"
37"
37"
Spoil Discharge Reach
24"
24"
18"
18"
18"
27"
27"
27"
27"
Weight
495 lb 775 lb
* For Low Flow Circuit ** For Low Flow Circuit/Side Shift Option
38
1040 lb
1200 lb
Manufacturer Index
Attachment Technologies Inc.
Delhi, IA 52223
Phone: (800) 922-2981
FFC Attachments
Lee, IL 60530
Phone: (800) 747-2132
Grouser Products
West Fargo, ND 58078
Phone: (800) 747-6182
Woods Equipment Corporation
Oregon, IL 61061
Phone: (815) 732-2141
39
NOTES
NOTES
KUSS151-02
©2005 Komatsu
Printed in USA
D(5M)CCI
4/05 (EV-1)
440 N. Fairway Dr.
Vernon Hills, IL 60061
www.KomatsuAmerica.com
Materials and specifications are subject to change without notice
is a trademark of Komatsu Ltd. Japan