Warranty Message The product you purchased comes with a Limited Warranty from MotorGuide. The terms of the policy are set forth in the Warranty Information section of this manual. The policy statement contains a description of the duration of coverage, important disclaimers and limitations of damages, and other related information. Please review this important information. The description and specifications contained herein were in effect at the time this manual was approved for printing. MotorGuide, whose policy is one of continued improvement, reserves the right to discontinue models at any time, to change specifications, designs, methods, or procedures without notice and without incurring obligation. MotorGuide, Tulsa, Oklahoma U.S.A. Litho in U.S.A. © 2008, Mercury Marine. All Rights Reserved. Reproduction in whole or in part without permission is prohibited. VariMAX and BluVis are trademarks of Brunswick Corporation. Mercury, Mercury Marine, MerCruiser, Mercury MerCruiser, Mercury Racing, MotorGuide, Gator, Machete, Mercury Precision Parts, Mercury Propellers, Mariner, Quicksilver, #1 On The Water, Alpha, Bravo, Bravo Two, Pro Max, OptiMax, Sport‑Jet, K‑Planes, MerCathode, SmartCraft, Total Command, VesselView, Zero Effort, Zeus, M with Waves logo, Mercury with Waves logo, and SmartCraft logo are all registered trademarks of Brunswick Corporation. Mercury Product Protection logo is a registered service mark of Brunswick Corporation. 90-8M4002068 1008 *8M4002068* NEVER STOP LEARNING, NEVER STOP IMPROVING, AND NEVER, EVER STOP FISHING. VariMAX Thank you for choosing MotorGuide® VariMAX™. With VariMAX, MotorGuide capitalized on many years of experience to provide you with a motor designed to deliver Digital Variable Speed Control and maximum time on the water. We designed VariMAX with a BluVis™ Function Display to show precise speed setting and battery voltage so you are always in control. The VariMAX Digital Advantage lets you dial in the exact speed for your boat to match the fishing conditions of the day while providing significantly longer run times on your battery charge. The VariMAX motor and its controls are designed to be very intuitive. You will need to properly install the handle, so please take the time to read this manual. Remember to keep your receipt and immediately register your trolling motor. A warranty card is enclosed or you can complete registration on the internet at www.motorguide.com. At MotorGuide, we believe there are some things you should Never Stop doing. © 2008 Mercury Marine Thank You TABLE OF CONTENTS Section 1 - Warranty Information MotorGuide Limited Warranty.................................. 2 Section 2 - General Information Recording Serial Number........................................6 Transom Mount...................................................6 Bow Mount..........................................................7 Boater's Responsibilities..........................................7 Protecting People in the Water................................7 While You Are Trolling........................................7 While the Boat Is Stationary...............................8 Passenger Safety Message..................................... 8 Safe Boating Suggestions.......................................8 Section 3 - Product Overview and Assembly Component Identification.......................................10 VariMAX Transom Mount.................................10 VariMAX Bow Mount.........................................11 Attaching the Handle.............................................12 Extending and Retracting the Handle....................13 Installing the Propeller...........................................14 Section 4 - Wiring and Battery Information Battery Precautions...............................................18 Standard Practices And Procedures.....................18 Battery Recommendations....................................18 BluVis Battery Voltage Indicator............................19 Battery Connection................................................19 12‑Volt Battery Connection...............................20 24‑Volt Battery Connection...............................21 Section 5 - Mount Installation VariMAX Transom Mount Installation....................24 Pontoon Mount Installation....................................24 Gator 20.8 Breakaway Installation.........................25 Gator Flex 360.......................................................26 Section 6 - Operation Installing The Motor Into The Bow Mount..............30 Removing The Motor From The Bow Mount.........30 Stowing The Trolling Motor....................................30 Transom Mount.................................................30 Bow Mount........................................................32 Deploying The Trolling Motor................................33 Transom Mount.................................................33 Bow Mount........................................................34 90-8M4002068 OCTOBER 2008 Adjusting The Steering Tension............................35 Adjusting The Motor Depth....................................35 Speed Control........................................................36 Direction Control....................................................36 Transom Mount Application..............................37 Transom Mount—Backtrolling Application........37 Bow Mount Application.....................................37 Page i Section 7 - Maintenance and Storage Trolling Motor Care...............................................40 SELECTING REPLACEMENT PARTS........... 40 Inspection And Maintenance Schedule................40 Before Each Use..............................................40 After Each Use.................................................40 Every 100 Hours Of Use Or Annually..............40 Storage Preparation............................................. 40 Battery Inspection................................................. 41 Propeller Replacement.........................................41 Removing The Propeller..................................41 Installing The Propeller....................................42 Section 8 - Custom Applications Repositioning The Top Housing...........................44 Setting The Direction Control Switch.................... 45 Motor Control Wiring............................................ 46 Section 9 - Owner Service Assistance Troubleshooting.................................................... 50 Service Assistance...............................................50 Mercury Marine Service Offices........................... 51 Section 10 - Accessories Trolling Motor Accessories...................................54 Page ii 90-8M4002068 OCTOBER 2008 Section 1 - Warranty Information Section 1 - Warranty Information Table of Contents 1 MotorGuide Limited Warranty............................... 2 90-8M4002068 OCTOBER 2008 Page 1 Section 1 - Warranty Information MotorGuide Limited Warranty KEEP YOUR ORIGINAL PURCHASE RECEIPT OR BILL OF SALE. 1. For recreational use customers, MotorGuide electric trolling motors are warranted to the original retail purchaser to be free from defects in material or workmanship for the periods listed in the table below: 12 V Trolling Motors — 1 year warranty 24 V Trolling Motors — 2 year warranty 36 V Trolling Motors — 3 year warranty 2. To obtain warranty service, the purchaser should deliver or return the unit (postage prepaid and insured) to any MotorGuide Authorized Service Dealer. DO NOT RETURN TO PLACE OF PURCHASE unless they are an authorized service center. Products returned by mail should be carefully packaged and include a note describing the nature of the problem and/or service requested, customer address and phone number. A copy of the receipt, Bill of Sale, registration verification or other proof of purchase is required with the return of the product for warranty consideration. Warranty claims will not be accepted without presentation of purchase receipt for trolling motor, other verification of registration, or Bill of Sale for boat package. 3. MotorGuide, at its discretion, will repair or replace items covered under the terms of this warranty. Neither MotorGuide nor MotorGuide Service Dealers are responsible for damages to MotorGuide products due to repairs performed by anyone other than an Authorized MotorGuide Service Dealer. Neither MotorGuide nor Mercury Marine is responsible for failure or damage caused by improper installation, set‑up, preparation, or previous service or repair errors. 4. For commercial use and government use customers, MotorGuide electric trolling motors are warranted to the original retail purchaser to be free from defects in material or workmanship for one (1) year. Commercial use is defined as any work or employment‑related use of the product, or any use of the product which generates income, for any part of the warranty period, even if the product is only occasionally used for such purpose such as Rental Fleets, Guides, Fish Camps or similar operations. Warranty is not transferable to any subsequent purchaser. The Mercury Product Protection plan is not available to commercial use or government use customers. 5. MotorGuide Composite Shaft Limited Lifetime Warranty. MotorGuide composite shafts are warranted to the original retail purchaser to be free of defects in material or workmanship for the lifetime of the original purchaser. MotorGuide will provide a new composite shaft at no cost for any composite shaft which contains a defect in material or workmanship. The installation costs are the sole responsibility of the purchaser. 6. Warranty coverage is available to customers that purchase from an authorized Dealer or Retailer that is authorized by MotorGuide Marine to distribute the product in the country in which the sale occurred. Warranty coverage and duration varies by the country in which the owner resides. This warranty applies to MotorGuide Trolling Motors sold and used in the United States. This Limited Warranty begins on the date the product is first sold to a purchaser or the date on which the product is first put into service, whichever occurs first. MotorGuide Accessories are covered by this Limited Warranty for a coverage period of one (1) year from the date of retail sale. The repair or replacement of parts, or the performance of service under this warranty, does not extend the life of this warranty beyond its original expiration date. Promotional warranties are not included in this statement and coverage may vary by promotion. Product either sold or put into service more than six years from date of manufacture is excluded from warranty coverage. Page 2 90-8M4002068 OCTOBER 2008 Section 1 - Warranty Information 7. This warranty does not apply to normal worn parts, for example, worn cables, adjustments, or product damage due to; 1) neglect, lack of maintenance, accident, abnormal operation or improper installation or service; 2) abuse, such as, bent metal columns, bent armature shafts, broken control cables, etc., accidents, modifications, misuse, excessive wear or damage caused by an owner’s failure to provide reasonable and necessary installation or care; 3) use of an accessory or part not manufactured by MotorGuide or Mercury; 4) alteration or removal of parts; 5) opening the lower unit (motor) by anyone other than an authorized MotorGuide Service Center will void this warranty. 8. We reserve the right to improve the design of any Trolling Motor without assuming any obligation to modify any Trolling Motor previously manufactured. 9. All Serialized "Service‑Repair" trolling motors receive a (1) one year warranty. Non‑serialized "Service‑Repair" electric trolling motors are NOT warranted. "Service‑Repair" motor denotes a trolling motor sold by MotorGuide that may be used but has been inspected and may have had minor repairs. Original retail purchaser of a "Service‑Repair" motor is the first purchaser of the motor after it is denoted as "Service‑Repair". "Service Repair" motors have a blue sticker on the battery cable and box denoting "Manufacturer Certified Service Repair Motor". 10. This warranty will not apply to 1) haul out, launch, towing and storage, transportation charges and/or travel time, telephone or rental charges of any type, inconvenience, or loss of time or income, or other consequential damages; or 2) removal or replacement of boat partitions or material because of boat design for necessary access to the Product; or 3) disconnection and reconnection of hard‑wired trolling motors. 11. TERMINATION OF COVERAGE: Warranty coverage may be terminated for repossessed product, or product purchased at auction, from a salvage yard, from a liquidator, from an insurance company, from unauthorized marine dealers or boat builders, or other third party entities. 12. ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED FROM THIS WARRANTY, WARRANTIES OF MERCHANTABILITY AND FITNESS ARE EXCLUDED FROM THIS WARRANTY, IMPLIED WARRANTIES ARE LIMITED TO THE LIFE OF THIS WARRANTY. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS WHICH MAY VARY FROM STATE TO STATE. . . For Your Records: Model Number _______________________________ Serial Number _______________________________ 90-8M4002068 OCTOBER 2008 Page 3 Section 1 - Warranty Information Notes: Page 4 90-8M4002068 OCTOBER 2008 Section 2 - General Information Section 2 - General Information Table of Contents Recording Serial Number..................................... 6 Transom Mount .............................................. 6 Bow Mount ..................................................... 7 Boater's Responsibilities....................................... 7 Protecting People in the Water............................. 7 90-8M4002068 OCTOBER 2008 While You Are Trolling ................................... 7 While the Boat Is Stationary ........................... 8 Passenger Safety Message.................................. 8 Safe Boating Suggestions.................................... 8 2 Page 5 Section 2 - General Information Recording Serial Number Record the serial number for future reference. For warranty purposes, complete the enclosed warranty card or register your trolling motor at www.motorguide.com. Transom Mount The transom mount serial number decals are located underneath the transom mount and on the motor shaft. a b c b a 38438 a - Serial number b - Model identification number c - Voltage Page 6 90-8M4002068 OCTOBER 2008 Section 2 - General Information Bow Mount The bow mount and pontoon mount serial number decals are located on the friction tube and on the motor shaft. a b c b a 39060 a - Serial number b - Model identification number c - Voltage Boater's Responsibilities The operator (driver) is responsible for the correct and safe operation of the boat and safety of its occupants and general public. It is strongly recommended that each operator (driver) read and understand this entire manual before operating the trolling motor. Be sure at least one additional person on board is instructed in the basic operation of the trolling motor in case the driver is unable to operate the boat. Protecting People in the Water While You Are Trolling It is very difficult for a person in the water to take quick action to avoid a boat heading in their direction, even at slow speeds. 21604 Always slow down and exercise extreme caution any time you are boating in an area where there might be people in the water. 90-8M4002068 OCTOBER 2008 Page 7 Section 2 - General Information While the Boat Is Stationary ! WARNING A spinning propeller, a moving boat, or any solid device attached to the boat can cause serious injury or death to swimmers. Stop the trolling motor immediately whenever anyone in the water is near your boat. Shut off the trolling motor before allowing people to swim or be in the water near your boat. Passenger Safety Message Whenever the boat is in motion, observe the location of all passengers. A sudden reduction in boat speed, such as a sharp change of boat direction, could throw them off the boat. Safe Boating Suggestions In order to safely enjoy the waterways, familiarize yourself with local and other governmental boating regulations and restrictions, and consider the following suggestions. Use flotation devices. It is the law to have an approved personal flotation device of suitable size for each person aboard and have it readily accessible. Do not overload your boat. Most boats are rated and certified for maximum load (weight) capacities, refer to your boat capacity plate. If in doubt, contact your dealer or the boat's manufacturer. Perform safety checks and required maintenance. Follow a regular schedule and ensure all repairs are made properly. Never be under the influence of alcohol or drugs while boating (it is the law). Alcohol or drug use impairs your judgment and greatly reduces your ability to react quickly. Passenger boarding. Stop the trolling motor whenever passengers are boarding or unloading. Be alert. The operator of the boat is responsible by law to maintain a proper lookout by sight and hearing. The operator must have an unobstructed view particularly to the front. No passengers, load, or fishing seats should block the operators view when operating the boat. Underwater hazards. Reduce speed and proceed with caution whenever navigating in shallow water. Tripping hazards. To avoid a trip hazard, route all cables and wiring neatly and out of the way. Report accidents. Boat operators are required by law to file a Boating Accident Report with their state boating law enforcement agency when their boat is involved in certain boating accidents. A boating accident must be reported if 1) there is loss of life or probable loss of life, 2) there is personal injury requiring medical treatment beyond first aid, 3) there is damage to boats or other property where the damage value exceeds $500.00 or 4) there is complete loss of the boat. Seek further assistance from local law enforcement. Page 8 90-8M4002068 OCTOBER 2008 Section 3 - Product Overview and Assembly Section 3 - Product Overview and Assembly Table of Contents Component Identification.................................... 10 VariMAX Transom Mount ............................. 10 VariMAX Bow Mount .................................... 11 90-8M4002068 OCTOBER 2008 Attaching the Handle.......................................... 12 Extending and Retracting the Handle................. 13 Installing the Propeller........................................ 14 3 Page 9 Section 3 - Product Overview and Assembly Component Identification VariMAX Transom Mount a b c d j e i f g h 37906 abcd- Top housing BluVis function display Cam‑lock Push–pull direction and speed control e - Taper‑lock mount Page 10 fghij- Shaft Lower unit Propeller Steering tension collar One‑touch depth collar 90-8M4002068 OCTOBER 2008 Section 3 - Product Overview and Assembly VariMAX Bow Mount a b c d e f l g h i k j 39061 abcd- Top housing BluVis function display Cam‑lock Push–pull direction and speed control e - One‑touch depth collar f - Gator 20.8 Breakaway 90-8M4002068 OCTOBER 2008 ghijkl- Gator Flex 360 Decket Shaft Propeller Lower unit Steering tension collar Page 11 Section 3 - Product Overview and Assembly Attaching the Handle NOTE: For proper installation, assemble the trolling motor on a flat, level surface. 1. Ensure the battery cables are disconnected from the power source. 2. Align the tri‑lobe handle to the top housing using the flat groove on the extension handle. The handle extension spring should face up. a b c e d 38695 a - Top housing b - Handle extension spring c - O‑ring d - Cam‑lock e - Tri‑lobe handle 3. Press the handle extension spring while inserting the handle into the top housing. Adjust the handle to the desired length. 38664 Handle extension spring 4. After the tri‑lobe handle engages, move the O‑ring flush against the top housing. 38932 O‑ring Page 12 90-8M4002068 OCTOBER 2008 Section 3 - Product Overview and Assembly 5. Rotate the cam‑lock clockwise 180°. Move the cam‑lock flush against the top housing. 180° 39062 6. To secure the tri‑lobe handle, hold the handle steady while rotating and tightening the cam‑lock clockwise 180°. Verify that the handle, cam‑lock, and top housing are in alignment. 38693 Cam‑lock and top housing in alignment Extending and Retracting the Handle 1. Firmly grasp the tri‑lobe handle, then rotate and loosen the cam‑lock counter clockwise 180°. 180° 38938 2. Extend or retract the handle to the desired length. 38656 Extending handle 90-8M4002068 OCTOBER 2008 38662 Retracting handle Page 13 Section 3 - Product Overview and Assembly 3. To secure the tri‑lobe handle, hold the handle steady while rotating and tightening the cam‑lock clockwise 180°. Verify that the handle, cam‑lock, and top housing are in alignment. 38693 Cam‑lock and top housing in alignment Installing the Propeller ! WARNING Performing service or maintenance without first disconnecting the battery can cause product damage, personal injury, or death due to fire, explosion, electrical shock, or unexpected motor starting. Always disconnect the battery cables from the battery before maintaining, servicing, installing, or removing motor components. 1. Rotate the motor shaft to insert the propeller pin horizontally. 38630 Propeller pin 2. Install the propeller onto the motor shaft by engaging the propeller onto the propeller pin. 38538 3. Install the propeller nut. Tighten securely. 38536 Page 14 90-8M4002068 OCTOBER 2008 Section 3 - Product Overview and Assembly 4. Use a MotorGuide propeller wrench or pliers to tighten the propeller nut another ¼ turn. Recommended MotorGuide Accessory Description Part Number MotorGuide Prop Wrench Kit MGA050B6 . 90-8M4002068 OCTOBER 2008 Page 15 Section 3 - Product Overview and Assembly Notes: Page 16 90-8M4002068 OCTOBER 2008 Section 4 - Wiring and Battery Information Section 4 - Wiring and Battery Information Table of Contents Battery Precautions............................................ 18 Standard Practices And Procedures.................. 18 Battery Recommendations................................. 18 BluVis Battery Voltage Indicator......................... 19 Battery Connection............................................. 19 12‑Volt Battery Connection .......................... 20 24‑Volt Battery Connection .......................... 21 4 90-8M4002068 OCTOBER 2008 Page 17 Section 4 - Wiring and Battery Information Battery Precautions ! WARNING An operating or charging battery produces gas that can ignite and explode, spraying out sulfuric acid, which can cause severe burns. Ventilate the area around the battery and wear protective equipment when handling or servicing batteries. When charging batteries, an explosive gas mixture forms in each cell. Part of this gas escapes through holes in vent plugs and may form an explosive atmosphere around battery if ventilation is poor. This explosive gas may remain in or around battery for several hours after it has been charged. Sparks or flames can ignite this gas and cause an internal explosion which may shatter the battery. The following precautions should be observed to prevent an explosion: 1. Do not smoke near batteries being charged or which have been charged very recently. 2. Do not break live circuits at terminals of batteries because a spark usually occurs at the point where a live circuit is broken. Always be careful when connecting or disconnecting cable clamps on chargers. Poor connections are a common cause of electrical arcs which cause explosions. 3. Do not reverse polarity of battery terminal to cable connections. Standard Practices And Procedures • • • • Do not use the main engine battery to power the trolling motor. Disconnect the trolling motor from the battery when charging and after each use. Route the trolling motor wires on the opposite side of the boat from other miscellaneous boat wiring. Connect boat accessories directly to the main engine battery. Battery Recommendations • Use a 12‑volt, deep cycle marine battery. Refer to Battery Connection. • Install a 50‑amp manual reset circuit breaker in line with the trolling motor positive leads within 180 cm (72 in.) of the batteries. Use 13 mm (6‑gauge) battery cables if extending the existing wire beyond the standard battery cable. • Recommended MotorGuide Accessory Description Part Number Trolling Motor Power Plug 8M4000953 Trolling Motor SP (receptacle) 8M4000954 50‑Amp Alligator Clips 8M4000287 6‑Gauge Battery Cable and Terminals With 50‑Amp Manual Reset Breaker MM309922T 50‑Amp Manual Reset Breaker Page 18 MM5870 90-8M4002068 OCTOBER 2008 Section 4 - Wiring and Battery Information BluVis Battery Voltage Indicator Use the BluVis function display to determine battery voltage level. The battery indicator will display the voltage for three seconds when the motor is connected to the battery and when the speed control is turned off. Refer to the diagram below to reference remaining battery voltage for 12‑ and 24‑volt battery connections. 12-volt 24-volt 13.5-volts 13-volts 12.5-volts 12-volts 11.5-volts 11-volts 10.5-volts 10-volts 9.5-volts 9-volts 27-volts 26-volts 25-volts 24-volts 23-volts 22-volts 21-volts 20-volts 19-volts 18-volts 38890 90-8M4002068 OCTOBER 2008 Page 19 Section 4 - Wiring and Battery Information Battery Connection ! CAUTION Disconnecting or connecting the battery cables in the incorrect order can cause injury from electrical shock or can damage the electrical system. Always disconnect the negative (‑) battery cable first and connect it last. 12‑Volt Battery Connection a d RED BLK c b a - Power cable b - 50‑amp circuit breaker 37289 c - Jumper wire d - Common ground 1. Install a 50‑amp circuit breaker (not included) in line with the positive lead. 2. Connect the red battery lead from the power cable to the positive (+) battery post. 3. Connect the black battery lead from the power cable to the negative (–) battery post. Recommended MotorGuide Accessory Description 50‑Amp Manual Reset Breaker Page 20 Part Number MM5870 90-8M4002068 OCTOBER 2008 Section 4 - Wiring and Battery Information 24‑Volt Battery Connection a d BLK RED A GR Battery A c Battery B a - Power cable b - 50‑amp circuit breaker c b 37824 c - Jumper wire d - Common ground 1. Install a 50‑amp circuit breaker (not included) in line with the positive lead. 2. Connect the red battery lead from the power cable to the positive (+) post on battery B. 3. Connect the black battery lead from the power cable to the negative (–) post on Battery A. 4. Connect a jumper wire between the negative (–) post on Battery B to the positive (+) post on battery A. Recommended MotorGuide Accessory Description 50‑Amp Manual Reset Breaker 90-8M4002068 OCTOBER 2008 Part Number MM5870 Page 21 Section 4 - Wiring and Battery Information Notes: Page 22 90-8M4002068 OCTOBER 2008 Section 5 - Mount Installation Section 5 - Mount Installation Table of Contents VariMAX Transom Mount Installation................. 24 Pontoon Mount Installation................................. 24 Gator 20.8 Breakaway Installation...................... 25 Gator Flex 360.................................................... 26 5 90-8M4002068 OCTOBER 2008 Page 23 Section 5 - Mount Installation VariMAX Transom Mount Installation NOTE: Fits transoms up to 8.25 cm (3.25 in.) thick. 1. Select an appropriate area on the transom of the boat to install the mount. 2. Retract the transom clamp screws. 3. Place the transom mount over the transom of the boat. Ensure the mount is secure. 39065 IMPORTANT: Overtightening the transom clamp screws can weaken or damage the mount bracket. 4. Tighten the transom clamp screws securely. Pontoon Mount Installation IMPORTANT: Choose an area on the deck with a 2.5 cm (1 in.) clearance from the bow of the boat for all motor positions including run and stow positions. 1. Select an appropriate area on the deck of the boat to install the mount. 39066 2. Place the pontoon mount base on the surface of the boat deck. Use the mount base as a template to mark the location of the mount holes. 37927 Pontoon mount holes Page 24 90-8M4002068 OCTOBER 2008 Section 5 - Mount Installation IMPORTANT: Using a larger drill bit, countersink the holes on fiberglass boats to prevent the gel‑coat from cracking. 3. Drill the mounting holes with a 7 mm (1/4 in.) diameter drill bit. Remove any debris. 4. Install four stainless steel washers and locking nuts onto the mounting screws underneath the boat deck. Tighten securely. Gator 20.8 Breakaway Installation 37805 Gator 20.8 Breakaway IMPORTANT: Choose an area on the deck with a 7.6 cm (3 in.) clearance from the bow of the boat for all motor positions including run and stow positions. 1. Select an appropriate area on the deck of the boat to install the mount. Ensure that the forward mounting screws will not penetrate the hull. 38094 Mount on deck 2. Place the bow mount base on the surface of the boat deck. Use the mount base as a template to mark the locations of the front mounting holes in the plastic decket and the rear mounting holes on the mount base. 38097 Mount base mounting holes 3. Drill the mounting holes with a 7 mm (1/4 in.) diameter drill bit. Remove any debris. 4. Re‑drill each mounting hole with a 13 mm (1/2 in.) diameter drill bit. IMPORTANT: Using a larger drill bit, countersink the holes on fiberglass boats to prevent cracking. 90-8M4002068 OCTOBER 2008 Page 25 Section 5 - Mount Installation 5. Insert the rubber mounting isolators into the drilled holes. Position the isolators in‑line with the mount base with the wider side toward the outside of the mount bracket. 39076 6. Place the mount bracket on the isolators and align the holes. Install the two longer screws into the front mounting holes and the two shorter screws into the rear mounting holes. Tighten all of the mounting screws securely with a Phillips screwdriver. IMPORTANT: The bracket must lay flush against the isolators before bolted to the deck or the mount will bind, making it difficult or impossible to unlatch. 7. Once installed, the bracket should fasten securely and evenly, with the latch pins in the latch, and release with a light, quick snap of the rope handle. Gator Flex 360 37806 Gator Flex 360 IMPORTANT: Choose an area on the deck with a 7.6 cm (3 in.) clearance from the bow of the boat for all motor positions including run and stow positions. 1. Select an appropriate area on the deck of the boat to install the mount. Ensure that the forward mounting screws will not penetrate the hull. 39074 Mount on deck Page 26 90-8M4002068 OCTOBER 2008 Section 5 - Mount Installation 2. Place the bow mount base on the surface of the boat deck. Use the mount base as a template to mark the locations of the front mounting holes in the plastic decket and the rear mounting holes on the mount base. 39075 Mount base mounting holes 3. Drill the mounting holes with a 7 mm (1/4 in.) diameter drill bit. Remove any debris. IMPORTANT: Using a larger drill bit, countersink the holes on fiberglass boats to prevent cracking. 4. Insert the rubber washers between the base of the mount and the boat mounting surface. Install the steel washers and nylon locking nuts onto the mounting screws underneath the boat deck. Tighten securely with a Phillips screwdriver and 11 mm (7/16 in.) wrench. IMPORTANT: If necessary, shim the rubber washers with 25 mm (1 in.) stainless steel washers to create a level mounting surface. 5. Once installed, the bracket should fasten securely and evenly, with the latch pins in the latch, and release with a light, easy pull on the rope handle. 6. Using a Phillips screwdriver and the decket screws, secure the decket to the mount base. 90-8M4002068 OCTOBER 2008 Page 27 Section 5 - Mount Installation Notes: Page 28 90-8M4002068 OCTOBER 2008 Section 6 - Operation Section 6 - Operation Table of Contents Installing The Motor Into The Bow Mount........... 30 Removing The Motor From The Bow Mount....... 30 Stowing The Trolling Motor................................. 30 Transom Mount ............................................ 30 Bow Mount ................................................... 32 Deploying The Trolling Motor.............................. 33 Transom Mount ............................................ 33 Bow Mount ................................................... 34 Adjusting The Steering Tension......................... 35 Adjusting The Motor Depth................................. 35 Speed Control..................................................... 36 Direction Control................................................. 36 Transom Mount Application ......................... 37 Transom Mount—Backtrolling Application ..................................................................... 37 Bow Mount Application ................................. 37 6 90-8M4002068 OCTOBER 2008 Page 29 Section 6 - Operation Installing The Motor Into The Bow Mount 39156 Bracket door knob 1. Turn the bracket door knob counter clockwise to loosen and open the bracket door. 2. Place the motor column into the bracket and close the door. 3. Turn the bracket door knob clockwise to tighten the motor column in the bracket. Removing The Motor From The Bow Mount 39156 Bracket door knob 1. Turn the bracket door knob counter clockwise to loosen and open the bracket door. 2. Remove the motor column from the bracket and close the door. Stowing The Trolling Motor ! WARNING Rotating propellers can cause serious injury or death. Never start or operate the motor out of water. ! CAUTION Moving parts, such as hinges and pivot points, can cause serious injury. Keep away from moving parts when stowing, deploying, or tilting the motor. Transom Mount IMPORTANT: Ensure the mount is stowed while using the main engine or trailering the boat. Ensure the steering tension collar is tightened securely. Page 30 90-8M4002068 OCTOBER 2008 Section 6 - Operation NOTE: The mount orientation of the motor determines the functionality of the taper‑lock knob. Push or pull the taper‑lock knob to release the taper‑lock pin. 1. Firmly grasp the column and push–or pull–the taper‑lock knob. 38787 Taper‑lock knob IMPORTANT: Do not use the handle to stow or tilt the motor. 2. Tilt the motor toward you by pulling back on the column while simultaneously pushing– or pulling–the taper‑lock knob. 38786 Taper‑lock knob 3. Once the motor is stowed, release the taper‑lock knob. Verify the taper‑lock pin is securely engaged by pushing–or pulling–on the taper‑lock knob. 38773 Taper‑lock knob 90-8M4002068 OCTOBER 2008 Page 31 Section 6 - Operation 4. Secure the motor by moving the depth collar flush against the steering tension collar. b a 39096 a - Depth collar b - Steering tension collar Bow Mount NOTE: This bow mount stowing procedure applies to both the Gator 20.8 Breakaway mount (pictured) and the Gator Flex 360 mount. 1. Firmly grasp the mount rope handle. 2. Snap the mount rope handle to disengage the lock pin. 3. Continue to pull the mount rope handle to raise the lower unit onto the mount. 38400 Mount rope IMPORTANT: Gently raise the trolling motor out of the water. Do not release the mount rope handle until the lock pin is engaged. 4. Once the motor is in the stow position, the lock pin engages to secure the trolling motor. 38516 VariMAX stowed Page 32 90-8M4002068 OCTOBER 2008 Section 6 - Operation Deploying The Trolling Motor ! WARNING Rotating propellers can cause serious injury or death. Never start or operate the motor out of water. ! CAUTION Moving parts, such as hinges and pivot points, can cause serious injury. Keep away from moving parts when stowing, deploying, or tilting the motor. Transom Mount NOTE: The mount orientation of the motor determines the functionality of the taper‑lock knob. Push or pull the taper‑lock knob to release the taper‑lock pin. 1. Firmly grasp the column and push–or pull–the taper‑lock knob. 39098 Taper‑lock knob IMPORTANT: Do not use the handle to tilt or deploy the motor. 2. Adjust the angle of the motor to the desired position while simultaneously pushing–or pulling–the taper‑lock knob. 38786 Taper‑lock knob 90-8M4002068 OCTOBER 2008 Page 33 Section 6 - Operation 3. Release the taper‑lock knob. Verify that the taper‑lock pin is securely engaged. 39100 Taper‑lock knob 4. Grasp the shaft with one hand and pinch the depth collar to lower the trolling motor to the desired depth. ! CAUTION Avoid possible serious injury from the motor dropping suddenly when adjusting the motor depth. Firmly grasp the motor shaft with one hand when raising or lowering the motor. Bow Mount NOTE: This bow mount deploying procedure applies to both the Gator 20.8 Breakaway mount (pictured) and the Gator Flex 360 mount. 1. Firmly grasp the mount rope handle. 2. Snap the mount rope handle to disengage the lock pin. 3. Continue to pull the mount rope handle to lower the trolling motor into the water. IMPORTANT: Gently lower the trolling motor into the water. Do not release the mount rope handle until the lock pin is engaged. 39020 Mount rope Page 34 90-8M4002068 OCTOBER 2008 Section 6 - Operation 4. Once the motor is in the deployed postion, the lock pin will engage to secure the trolling motor. 38906 VariMAX deployed Adjusting The Steering Tension Adjust the steering tension collar to increase or decrease the effort to turn the motor freely. 1. To fasten the column in a fixed position, turn the steering tension collar clockwise. 2. To unfasten the column from a fixed position, turn the steering tension collar counterclockwise to reach the desired steering tension. 38437 Steering tension collar Adjusting The Motor Depth ! CAUTION Avoid possible serious injury from dropping the motor when adjusting the motor depth. Firmly grasp the motor shaft with one hand when raising or lowering the motor. Adjust the depth of the motor to improve trolling motor performance in various water depths. IMPORTANT: When adjusting the motor depth, ensure the lower unit is fully submerged to avoid propeller cavitation. 1. Firmly grasp the column with one hand while holding the depth collar. 2. Pinch the depth collar until the motor column slides freely. 90-8M4002068 OCTOBER 2008 Page 35 Section 6 - Operation 3. Raise or lower to the desired depth. 38436 Motor depth collar Speed Control MotorGuide VariMAX motors offer a new digital method of variable speed control that provides more efficient power consumption and precise speed control in 270° of handle rotation. VariMAX Digital variable speed control allows you to set the exact speed you want, whether in forward or reverse, for maximum control. NOTE: Speed control is operable regardless of handle position. For top housing reorientation, refer to Custom Applications. Rotate the handle clockwise to increase speed in both forward and reverse directions. The BluVis function display indicates speed‑setting. b 100% 90% 80% 70% 60% 50% 40% 30% 20% 10% a 38443 a - Rotate the handle clockwise b - Bluvis function display with speed‑settings Direction Control The intuitive push–forward, pull–reverse direction control lets you increase the speed by turning the handle clockwise, whether in forward or reverse. To shift and change the direction of the propeller, simply pull back or push forward on the handle. The BluVis funtion display shows your relative speed setting and direction when the propeller is moving. Page 36 90-8M4002068 OCTOBER 2008 Section 6 - Operation IMPORTANT: To shift the motor and change the direction of the propeller, the power must be below 50% to provide instant direction control for forward and reverse. The motor will only shift if below the 50% speed setting to protect the motor from damage. Transom Mount Application To move the boat forward, pull the handle. To move the boat in reverse, push the handle. The BluVis function display indicates the motor direction. 39101 39222 Reverse Forward Transom Mount—Backtrolling Application To use the transom mount for backtrolling, reverse the top housing position and toggle the direction control switch. Refer to Custom Applications. To backtroll, pusd the handle. To reverse backtroll, pull the handle. The BluVis function display indicates the motor direction. 39102 39223 Backtroll reverse Backtroll Bow Mount Application To move the boat forward, push the handle. To move the boat in reverse, pull the handle. The BluVis function display indicates the motor direction. 39224 Reverse 90-8M4002068 OCTOBER 2008 39103 Forward Page 37 Section 6 - Operation Notes: Page 38 90-8M4002068 OCTOBER 2008 Section 7 - Maintenance and Storage Section 7 - Maintenance and Storage Table of Contents Trolling Motor Care............................................. 40 SELECTING REPLACEMENT PARTS ........ 40 Inspection And Maintenance Schedule.............. 40 Before Each Use .......................................... 40 After Each Use ............................................. 40 Every 100 Hours Of Use Or Annually .......... 40 Storage Preparation............................................ 40 Battery Inspection............................................... 41 Propeller Replacement....................................... 41 Removing The Propeller .............................. 41 Installing The Propeller ................................ 42 7 90-8M4002068 OCTOBER 2008 Page 39 Section 7 - Maintenance and Storage Trolling Motor Care To keep your trolling motor in the best operating condition and retain its dependability, your trolling motor must receive periodic inspections and maintenance. Keep it maintained properly to ensure the safety of you and your passengers. ! WARNING Neglecting to inspect, maintain, or repair your trolling motor can result in product damage or serious injury or death. Do not perform maintenance or service on your trolling motor if you are not familiar with the correct service and safety procedures. Record all maintenance performed and save maintenance work orders and receipts. SELECTING REPLACEMENT PARTS Original MotorGuide Certified Tough replacement parts. Inspection And Maintenance Schedule Before Each Use • • • • Check the tightness of the battery lead connections. Visually inspect for loose or corroded wiring connections. Check the tightness of the propeller nut. Check the propeller blades for damage. After Each Use • • • • Disconnect the battery cables from the power source or unplug the motor from the boat. After each use, check the propeller and propeller shaft for debris such as weeds and fishing line. Remove all debris. Check the tightness of the propeller nut. Rinse the trolling motor with clean water to remove dirt and dust that may scratch the surface. Every 100 Hours Of Use Or Annually • Periodically lubricate all the pivot points with a non‑aerosol, non‑solvent based lubricant. IMPORTANT: Never use an aerosol lubricant to grease or oil any part of the unit. Many aerosol lubricants contain harmful propellants that can cause damage to various parts of the trolling motor. Tube Ref No. 95 • • Description 2-4-C with Teflon Where Used Part No. Pivot points 92-802859A 1 Check the tightness of bolts, nuts, and other fasteners. Inspect the battery. Refer to Battery Inspection. Storage Preparation The major consideration in preparing your trolling motor for storage is to protect it from corrosion and damage caused by freezing of trapped water. Page 40 90-8M4002068 OCTOBER 2008 Section 7 - Maintenance and Storage Refer to the Maintenance - Inspection and Maintenance Schedule section and complete the appropriate care instructions to prepare your trolling motor for storage. Store the trolling motor in a dry location where it will not be affected by temperatures below ‑29 °C (‑20 °F). IMPORTANT: Trolling motors stored in temperatures below 0 °C (32 °F) should be operated slowly for a minimum of 15 minutes before going above 30% operation. Battery Inspection The battery should be inspected at periodic intervals to ensure proper trolling motor operation. IMPORTANT: Read the safety and maintenance instructions which accompany your battery. 1. Ensure that the battery is secured to the vessel. 2. Ensure that the battery cable terminals are clean, tight, and correctly installed. For installation instructions, refer to Battery Connection. 3. Ensure that the battery is equipped with a battery box to prevent accidental shorting of the battery terminals. Propeller Replacement ! WARNING Performing service or maintenance without first disconnecting the battery can cause product damage, personal injury, or death due to fire, explosion, electrical shock, or unexpected motor starting. Always disconnect the battery cables from the battery before maintaining, servicing, installing, or removing motor components. Removing The Propeller 1. Disconnect the battery cables from the power source. 2. While holding the propeller blade with one hand, use a propeller wrench or pliers to remove the propeller nut. IMPORTANT: If the propeller cannot be removed easily, hold one blade and use a rubber mallet to lightly tap the back side of the opposite blade. If the propeller cannot be removed, refer to Troubleshooting. NOTE: If the propeller pin is bent, replace the propeller pin. 38536 Recommended MotorGuide Accessory Description Part Number MotorGuide Prop Wrench Kit MGA050B6 90-8M4002068 OCTOBER 2008 Page 41 Section 7 - Maintenance and Storage Installing The Propeller 1. Rotate the motor shaft to insert the propeller pin horizontally. 38630 Propeller pin 2. Install the propeller onto the motor shaft by engaging the propeller onto the propeller pin. 38538 3. Install the propeller nut. Tighten securely. 38536 4. Use a MotorGuide propeller wrench or pliers to tighten the propeller nut another ¼ turn. Page 42 Recommended MotorGuide Accessory Description Part Number MotorGuide Prop Wrench Kit MGA050B6 90-8M4002068 OCTOBER 2008 Section 8 - Custom Applications Section 8 - Custom Applications Table of Contents Repositioning The Top Housing......................... 44 Setting The Direction Control Switch.................. 45 Motor Control Wiring........................................... 46 8 90-8M4002068 OCTOBER 2008 Page 43 Section 8 - Custom Applications Repositioning The Top Housing VariMAX transom mount motors are configured at the factory for use on the transom. We designed the VariMAX motors so the head could easily be reversed (eight head positions are available) to fit any application including bow, backtroller or sideways pulling applications. The BluVis lights can also be reversed to keep the intuitive push‑pull feel and control consistent. If you have a VariMAX bow mount or pontoon mount motor, it is already configured for bow mount applications. IMPORTANT: While configuring the top housing to a new position, you can toggle the position switch for the appropriate mount application. Refer to Setting The Direction Control Switch. 1. Ensure the battery cables are disconnected from the power source. 2. Loosen the top housing retaining bolt with a 5 mm diameter Allen wrench. Do not fully remove the retaining bolt. IMPORTANT: Do not fully remove the top housing retaining bolt or the retaining nut may fall out. Do not raise the top housing off of the column. Removing the top housing may disconnect the motor control wires. If the wires disconnect, refer to Motor Control Wiring for wire orientation. 38636 Allen wrench 3. Raise the top housing until the height pin disengages. 38670 Height pin 4. Rotate the top housing to the desired position and push the top housing back down to engage the height pin. b a 38638 a - Top housing b - Eight position settings 5. Tighten the top housing retaining bolt with an Allen wrench. Tighten securely. Page 44 90-8M4002068 OCTOBER 2008 Section 8 - Custom Applications Torque Description Nm lb‑in. lb‑ft Top housing retaining bolt 8.5 75 – 38636 Allen wrench Setting The Direction Control Switch VariMAX motors are configured to the intuitive push‑pull direction control. To use the transom mount on the bow of the vessel, reverse the top housing and toggle the direction control switch to set the motor and BluVis function display orientation for a bow application. To reverse the top housing, refer to Repositioning the Top Housing. 1. Disconnect the battery cables from the power source. 2. Loosen the top housing retaining bolt with an Allen wrench. Do not fully remove the retaining bolt. IMPORTANT: Do not fully remove the top housing retaining bolt or the retaining nut may fall out. Slowly raise the top housing off of the shaft ensuring that the motor control wires do not disconnect. If the wires are disconnected, refer to the Motor Control Wiring section for wire orientation. 38636 Allen wrench 3. Remove the top housing from the shaft. NOTE: Do not remove the heat‑sink grease on the motor shaft. Heat‑sink grease will not wash out of clothing. 39092 Top housing removed from shaft 4. Rotate the top housing upside‑down to expose the direction control switch inside. 5. Slide the switch away from the handle. 90-8M4002068 OCTOBER 2008 Page 45 Section 8 - Custom Applications NOTE: If necessary, use a flathead screwdriver to slide the direction control switch. A A B B 39225 39064 Transom application (default) Bow, pontoon or backtrolling application 6. Replace the top housing onto the motor shaft. 7. Rotate the top housing to the desired position and push the top housing back down to engage the height pin. b a 38638 a - Top housing b - Eight position settings 8. Retighten the top housing retaining bolt with a Allen wrench. Tighten securely. Torque Description Nm lb‑in. lb‑ft Top housing retaining bolt 8.5 75 – 38636 Allen wrench Motor Control Wiring ! WARNING Performing service or maintenance without first disconnecting the battery can cause product damage, personal injury, or death due to fire, explosion, electrical shock, or unexpected motor starting. Always disconnect the battery cables from the battery before maintaining, servicing, installing, or removing motor components. IMPORTANT: Disconnect the VariMAX motor control wiring for service only. Do do not reconfigure the motor control wiring when reorienting the motor top housing between transom and bow applications. Page 46 90-8M4002068 OCTOBER 2008 Section 8 - Custom Applications NOTE: If necessary, use needle‑nose pliers to connect the motor control wire to the respective terminal. Ensure the wiring connection is secure. A B A RED B BLK BLK RED 38772 39226 Transom 90-8M4002068 OCTOBER 2008 Bow or pontoon Page 47 Section 8 - Custom Applications Notes: Page 48 90-8M4002068 OCTOBER 2008 Section 9 - Owner Service Assistance Section 9 - Owner Service Assistance Table of Contents Troubleshooting.................................................. 50 Service Assistance............................................. 50 Mercury Marine Service Offices.......................... 51 9 90-8M4002068 OCTOBER 2008 Page 49 Section 9 - Owner Service Assistance Troubleshooting NOTE: For service information, contact any certified MotorGuide Service Center. For a full listing of MotorGuide service centers, go to www.motorguide.com or contact any Mercury Service office. Refer to Owner Service Assistance. Symptom Possible Cause Weak battery Loose or corroded battery connections Loss of power Propeller is loose, damaged or off‑balance Resolution Refer to Wiring and Battery Information. Refer to Maintenance. Wire gauge from the battery to the trolling Wiring or electrical connection faulty motor is insufficient. Six‑gauge wire is recommended. Motor shaft is bent Excessive noise, vibration Propeller is loose, damaged or off‑balance Refer to Service Center. Refer to Maintenance. Weak battery Loose or corroded battery connections Refer to Wiring and Battery Information. Wiring or electrical connection faulty. Motor failure (all speeds) Motor rotates in the wrong direction BluVis function display failure Difficulty removing propeller Electrical Check the connector for a loose or damaged connection. Refer to Wiring and Battery Information. Fuse on circuit breaker is open Replace the fuse or reset the circuit breaker only after determining the root cause of the problem. Direction control switch in wrong position Electrical Wiring or electrical connection faulty Bent propeller pin Bent armature shaft Refer to Assembly. Refer to Service Center. Check the battery connection. Refer to Wiring and Battery Information. Hold one blade and lightly tap the opposite blade with a rubber mallet. Use a putty knife on both sides of the propeller to apply equal pressure. Refer to Service Center. Service Assistance Your satisfaction with your product is very important to us. If you have a problem or question about your motor, contact your dealer or any certified MotorGuide Service Center. For more service assistance information, refer to Warranty Information. The following information will be needed by the service office: • Your name and address • Daytime telephone number • Model and serial number of your trolling motor • Proof of purchase or registration verification • Nature of problem Page 50 90-8M4002068 OCTOBER 2008 Section 9 - Owner Service Assistance Mercury Marine Service Offices For assistance, call, fax, or write. Please include your daytime telephone number with mail and fax correspondence. United States Telephone (920) 929‑5040 Fax (920) 929‑5893 Website www.motorguide.com Mercury Marine W6250 W. Pioneer Road Fond du Lac, WI 54936-1939 Canada Telephone (905) 567‑6372 Fax (905) 567‑8515 Mercury Marine Ltd. 2395 Meadowpine Blvd. Mississauga, Ontario L5N 7W6 Canada Australia, Pacific Telephone (61) (3) 9791‑5822 Fax (61) (3) 9793‑5880 Mercury Marine Australia 132-140 Frankston Road Dandenong, Victoria 3164 Australia Europe, Middle East, Africa Telephone (32) (87) 32 • 32 • 11 Fax (32) (87) 31 • 19 • 65 Marine Power - Europe, Inc. Parc Industriel de Petit-Rechain B-4800 Verviers, Belgium Mexico, Central America, South America, Caribbean Telephone (954) 744‑3500 Fax (954) 744‑3535 Mercury Marine 11650 Interchange Circle North Miramar, FL 33025 U.S.A. Japan Telephone 81‑053‑423‑2500 Fax 81‑053‑423‑2510 Mercury Marine - Japan Anshin-cho 283-1 Hamamatsu Shizuoka-ken, Japan 435-0005 Japan Asia, Singapore Telephone 5466160 Fax 5467789 90-8M4002068 OCTOBER 2008 Mercury Marine Singapore 72 Loyang Way Singapore, 508762 Page 51 Section 9 - Owner Service Assistance Notes: Page 52 90-8M4002068 OCTOBER 2008 Section 10 - Accessories Section 10 - Accessories Table of Contents Trolling Motor Accessories................................. 54 10 90-8M4002068 OCTOBER 2008 Page 53 Section 10 - Accessories Trolling Motor Accessories MotorGuide accessories available wherever trolling motors are sold. 2-Blade Power Prop Kit Hub size: 8.9 cm (3.5 in.) Application: power and efficiency Includes 2‑blade propeller, prop nut and large prop pin MGA0495B 39081 3-Blade Machete III Black Hub size: 8.9 cm (3.5 in.) Application: speed and efficiency Includes 3‑blade propeller, prop nut and large prop pin MGA089B 39082 3-Blade Machete III White Glass-Filled Hub size: 8.9 cm (3.5 in.) Application: speed and efficiency Includes 3‑blade propeller, prop nut and large prop pin MGA089W Hub size: 8.9 cm (3.5 in.) Application: shallow and durability Includes 3‑blade propeller, prop nut and large prop pin MGA087M 39083 3-Blade Aluminum Machete 39157 MotorGuide Prop Wrench Kit Comes complete with spare prop nut and two prop pins, allowing fast prop MGA050B6 changes. 37853 Replacement Handle With soft grip handle and Tour rope for unsurpassed durability. 8M4000275 39084 Mounting Isolators Absorbs shock and protects electronics. Ideal for mounting all marine accessories without having to go under the deck. Four per package. MGA015PB6 39086 Page 54 90-8M4002068 OCTOBER 2008 Section 10 - Accessories Trolling Motor Mounting Kit Absorbs shock and protects electronics. Steel bolts and washers fit all 8M4000873 trolling motors. Four per package. 39087 Trolling Motor Power Plug Two‑prong, 12‑, 24‑ or 36‑volt power plug provides a solid, safe connection. 8M4000953 38003 Trolling Motor SP (receptacle) Matching two‑prong 12‑, 24‑ or 36‑volt power plug provides a 8M4000954 solid, safe connection. 38004 6 Gauge Battery Cable and Terminals with 50‑Amp Manual Reset Breaker Protect your investment with this 50‑amp manual reset breaker and heavy‑duty 6‑gauge battery cable and terminal. MM309922T 38006 50‑Amp Manual Reset Breaker Protect your motor and boat wiring. MM5870 38007 50‑Amp Alligator Clips Feature upscale grip design and higher amp rating. 8M4000287 38005 14" Universal Extension Handle 39090 For transom mount and bow mount trolling motors. MGA504A1 24" Universal Telescoping Extension Handle 39089 For transom mount and bow mount trolling motors. MGA503A1 36" Universal Extension Handle 39088 90-8M4002068 OCTOBER 2008 For transom mount and bow mount trolling motors. 8M4000283 Page 55
© Copyright 2024