OPENING SINGLE TRACK CILL FIXING OPENING SINGLE TRACK

A4
TOLERANCES:
Construction tolerances between frames
is -0mm +2mm. Frames are manufactured
and assembled to +0mm -2mm.
OPENING SINGLE TRACK LINTEL FIXING
NOTE:- AN ADDITIONAL STUD IS REQUIRED
POSITIONED WITHIN 150mm (min) AND 225mm
(max) EITHER SIDE OF ALL STRUCTURAL
OPENINGS FOR A MASONARY FACADE
PROJECT FOR BRICK TIE CHANNEL FIXING
JAMB STUD
100mm LONG SWAGED CRIPPLE TRACK FIXED TO
JAMB STUD USING 3 No 5.5 x 25mm TEK SCREWS
(EOS02)
SIN
GL
E
LINTEL/CILL TRACK FIXED INTO CRIPPLE TRACK
USING 2 No 5.5 x 25 TEK SCREWS (WAFER HEADS)
(EOS05) ONE FIXING CENTRALLY INTO EACH
FLANGE.
TR
AC
KL
IN
TE
SIN
GL
E
100mm LONG SWAGED CRIPPLE TRACK FIXED TO
JAMB STUD USING 3No 5.5 x 25 TEK SCREWS
(EOS02)
L
TR
AC
KC
ILL
JAMB STUD
OPENING SINGLE TRACK CILL FIXING
BA
Title:
TYPICAL OPENING - SINGLE TRACK LINTEL & CILL CONNECTION DETAIL (S & T)
STAGE:
Preliminary:
Approval:
Construction:
Drawn By:
Scale:
n.t.s.
Drawing No.
Revision:
261
A
Approved By:
Date:
SE
T
RA
CK
DRAWING INDICATIVE ONLY:
A4
TOLERANCES:
Construction tolerances between frames
is -0mm +2mm. Frames are manufactured
and assembled to +0mm -2mm.
NOTE:- AN ADDITIONAL STUD IS REQUIRED
POSITIONED WITHIN 150mm (min) AND 225mm
(max) EITHER SIDE OF ALL STRUCTURAL
OPENINGS FOR A MASONARY FACADE
PROJECT FOR BRICK TIE CHANNEL FIXING
100mm LONG CRIPPLE TRACK FIXED TO JAMB
STUD USING 3 No 5.5 x 25mm TEK SCREWS (EOS02)
LIN
OPENING SINGLE JAMB AND
DOUBLE STUD LINTEL FIXING
TE
L
TR
AC
K
JAMB STUD
SWAGED DOUBLE STUD LINTEL / CILL FIXED INTO
CRIPPLE TRACK USING 2 No 5.5 x 25mm TEK
SCREWS (WAFER HEADS) (EOS05) ONE FIXING
CENTRALLY INTO EACH FLANGE.
DOUBLE STUD LINTEL / CILL FORMED
FROM 2 No. STUDS CONNECTED
BY NOGGINS @ 600mm c/c. WITH
TRACK TOP OR BOTTOM
DOUBLE STUD LINTEL / CILL FIXED TOGETHER
USING 5.5 x 25mm TEK SCREWS (WAFER HEADS)
(EOS05) 4 FIXINGS PER NOGGIN. DOUBLE STUD
LINTEL / CILL FIXED TO LINTEL & CILL TRACK
USING 5.5 x 25mm TEK SCREWS (EOS02) @ 600mm
CENTRES.
JAMB STUD
100mm LONG CRIPPLE TRACK FIXED TO JAMB
STUD USING 3No 5.5 x 25mm TEK SCREWS (EOS02)
CIL
L
DOUBLE STUD LINTELS / CILLS
MANUFACTURED ONSITE BY INSTALLERS OR
OFFSITE IN EOS FACTORY (PROJECT SPECIFIC)
OPENING SINGLE JAMB AND
DOUBLE STUD CILL FIXING
Title:
BA
TYPICAL OPENING - SINGLE JAMB & DOUBLE STUD LINTEL & CILL
CONNECTION DETAIL (S & T)
SE
T
RA
CK
STAGE:
Preliminary:
Approval:
Construction:
Drawn By:
Scale:
n.t.s.
Drawing No.
Revision:
262
A
Approved By:
Date:
TR
AC
K
DRAWING INDICATIVE ONLY:
A4
TOLERANCES:
Construction tolerances between frames
is -0mm +2mm. Frames are manufactured
and assembled to +0mm -2mm.
NOTE:- DOUBLE STUDS ARE STANDARDLY MANUFACTURED
AT 100mm WIDE HOWEVER THEY CAN BE MANUFACTURED
WIDER TO ENCAPSULATE THE ADDITIONAL STUD AS
REQUIRED TO BE POSITIONED WITHIN 150mm (min) AND
225mm (max) EITHER SIDE OF ALL STRUCTURAL OPENINGS
FOR A MASONARY FACADE PROJECT FOR BRICK TIE
CHANNEL FIXING
LIN
100mm LONG CRIPPLE TRACK FIXED TO JAMB
STUD USING 3No 5.5 x 25mm TEK SCREWS (EOS02)
TE
L
TR
AC
K
OPENING DOUBLE STUD JAMB AND
DOUBLE STUD LINTEL FIXING
DOUBLE JAMB STUD
SWAGED DOUBLE STUD LINTEL / CILL FIXED INTO
CRIPPLE TRACK USING 2 No 5.5 x 25mm TEK
SCREWS (WAFER HEADS) (EOS05) ONE FIXING
CENTRALLY INTO EACH FLANGE.
DOUBLE STUD LINTEL / CILL FORMED
FROM 2 No. STUDS CONNECTED
BY NOGGINS @ 600mm c/c. WITH
TRACK TOP OR BOTTOM
DOUBLE STUD LINTEL / CILL FIXED TOGETHER
USING 5.5 x 25mm TEK SCREWS (WAFER HEADS)
(EOS05) 4 FIXINGS PER NOGGIN. DOUBLE STUD
LINTEL / CILL FIXED TO LINTEL & CILL TRACK
USING 5.5 x 25mm TEK SCREWS (EOS02) @ 600mm
CENTRES.
DOUBLE JAMB STUD
100mm LONG CRIPPLE TRACK FIXED TO JAMB
STUD USING 3 No 5.5 x 25mm TEK SCREWS (EOS02)
CIL
L
DOUBLE STUD & DOUBLE STUD LINTELS / CILLS
MANUFACTURED ONSITE BY INSTALLERS OR
OFFSITE IN EOS FACTORY (PROJECT SPECIFIC)
OPENING DOUBLE STUD JAMB AND
DOUBLE STUD CILL FIXING
Title:
BA
TYPICAL OPENING - DOUBLE STUD JAMB & DOUBLE STUD LINTEL & CILL
CONNECTION DETAIL (S & T)
SE
T
RA
CK
STAGE:
Preliminary:
Approval:
Construction:
Drawn By:
Scale:
n.t.s.
Drawing No.
Revision:
263
A
Approved By:
Date:
TR
AC
K
DRAWING INDICATIVE ONLY:
A4
TOLERANCES:
Construction tolerances between frames
is -0mm +2mm. Frames are manufactured
and assembled to +0mm -2mm.
A
HE
D
K
AC
TR
AD
HE
K
AC
TR
HEAD FIXING
DEFLECTION HEAD FIXING
DOUBLE STUD MANUFACTURED ONSITE BY
INSTALLERS OR OFFSITE IN EOS FACTORY
(PROJECT SPECIFIC)
DOUBLE STUDS CONNECTED USING NOGGINS
FIXED WITH 4 No. 5.5 x 25mm TEK SCREWS (EOS05)
NOGGINS AT 600mm CENTRES.
BASE FIXING
NOTE:- DOUBLE STUDS ARE STANDARDLY MANUFACTURED
AT 100mm WIDE HOWEVER THEY CAN BE MANUFACTURED
WIDER TO ENCAPSULATE THE ADDITIONAL STUD AS
REQUIRED TO BE POSITIONED WITHIN 150mm (min) AND
225mm (max) EITHER SIDE OF ALL STRUCTURAL OPENINGS
FOR A MASONARY FACADE PROJECT FOR BRICK TIE
CHANNEL FIXING
CK
RA
T
SE
BA
Title:
TYPICAL DOUBLE STUD CONNECTION DETAIL (S & T)
STAGE:
Preliminary:
Approval:
Construction:
Drawn By:
Scale:
n.t.s.
Drawing No.
Revision:
265
A
Approved By:
Date:
DRAWING INDICATIVE ONLY:
A4
TOLERANCES:
Construction tolerances between frames
is -0mm +2mm. Frames are manufactured
and assembled to +0mm -2mm.
DOUBLE JAMB STUD AND LATTICE LINTEL
FABRICATED ONSITE BY INSTALLERS
OR OFF SITE BY EOS (PROJECT SPECIFIC).
LA
TT
IC
LATTICE FIXED TO DOUBLE
STUD USING 4 No 5.5 x 25mm
TEK SCREWS (EOS02)
EL
IN
TE
L
DOUBLE JAMB STUD WITH
SHORTENED INNER STUD
TO PROVIDE BEARING FOR
LATTICE.
LATTICE DEPTH TO SUIT HEIGHT
BETWEEN WINDOW HEAD AND
FLOOR / ROOF ABOVE.
AD
HE
BEARING NOGGING FIXED TO
DOUBLE STUD USING
4 No. 5.5 x 25mm TEK SCREWS (WAFER HEADS) (EOS05)
LATTICE FIXED TO BEARING
USING 2 No 5.5 x 25mm TEK SCREWS (EOS02)
Title:
TYPICAL LATTICE LINTEL DETAIL (S & T)
STAGE:
Preliminary:
Approval:
Construction:
Drawn By:
Scale:
n.t.s.
Drawing No.
Revision:
266
A
Approved By:
Date:
OF
G
IN
EN
P
O
DRAWING INDICATIVE ONLY:
A4
TOLERANCES:
Construction tolerances between frames
is -0mm +2mm. Frames are manufactured
and assembled to +0mm -2mm.
NOTE : Orientation of studs 2 & 3 must be web to web facing
50mm x 1mm Flat strap to run across full bay. 2 No fixings into each stud.
Strap to be fitted on Internal face of Studs at all times.
Cloaking Track
1
2
3
Cripple track fixed onto the back web of the vertical stud.
Track then cloaks the two cripple tracks and fixed as shown
Plan on Typical Corner
Step 1
Step 3
Step 2
2 No fixings EOS S & T site fix
(EOS 05)
Flat plate runs full length of bay.
50mm x1mm thk,
1 No fixing into flange of stud
EOS S&T Site fixings
(EOS 05)
Track cloaks cripple tracks EOS S&T site fixing
into both flanges
(EOS 05)
Cripple Track
Strap to be fitted to track
2 No fixings (EOS 05)
This detail is to be used in all situations where a mid-height restraint is required.
Length of mid-height restraint to be specified by Engineer.
Stud Size and Spacing to be Job Specific specified by EOS
Title:
TYPICAL STUD AND TRACK MID HEIGHT RESTRAINT DETAIL (S & T)
STAGE:
Preliminary:
Approval:
Construction:
Drawn By:
Scale:
n.t.s.
Drawing No.
Revision:
269
A
Approved By:
Date:
A4
TOLERANCES:
Construction tolerances between frames
is -0mm +2mm. Frames are manufactured
and assembled to +0mm -2mm.
NOTE:- SLAB NOT SHOWN FOR CLARITY.
PLEASE USE DEFLECTION HEAD DETAIL 211 TO
CONNECT STUD TO HEAD TRACK
THIS DETAIL CAN BE ADOPTED FOR VENT
OPENINGS UP TO THE MAXIMUM SIZE AVAILABLE
BETWEEN THE STUDS AT THE REQUIRED CENTRES FOR OTHER SIZES PLEASE CONSULT EOS ENGINEERS
TYPICAL VENT OPENING
ELEVATION
THE HEAD TRACK CAN BE CUT OUT LOCALLY IF
IT CLASHES WITH THE VENT HOWEVER PLEASE
ENSURE THAT A FIXING IS PLACED A MAXIMUM OF
50mm AWAY FROM EACH END OF TRACK
OPENING TRACK FIXED INTO CRIPPLE TRACK
USING 2 No 5.5 x 25mm TEK SCREWS (WAFER
HEADS) (EOS05) ONE FIXING CENTRALLY INTO
EACH FLANGE.
TR
AC
KF
OR
MI
NG
OP
EN
IN
G
JAMB STUD
100mm LONG SWAGED CRIPPLE TRACK FIXED TO
JAMB STUD USING 3 No 5.5 x 25mm TEK SCREWS
(EOS02)
Title:
TYPICAL VENT OPENING CONNECTION DETAIL (S & T)
STAGE:
Preliminary:
Approval:
Construction:
Drawn By:
Drawing No.
Scale:
n.t.s.
270
Revision:
Approved By:
Date:
A4
TOLERANCES:
Construction tolerances between frames
is -0mm +2mm. Frames are manufactured
and assembled to +0mm -2mm.
DEFLECTION BRACKETS ARE NOT REQUIRED ON THE STUDS ABOVE THE OPENING FOR
A HARD FIXED LINTEL - DEFLECTION IS TO BE ALLOWED FOR ABOVE THE WINDOW
WINDOW MANUFACTURER TO ALLOW
ADDITIONAL TOLERANCE FOR MOVEMENT /
DEFLECTION ABOVE THE HEAD OF THE WINDOW
TYPICAL HARD FIXED LINTEL ELEVATION
Head track (Fixing to
suit structure)
TYPICAL SECTION
Alternative fixing
position.
mm minimum.
NOTE:- PROJECT SPECIFIC HARD FIXED
LINTEL DETAILS WILL BE PROVIDED DURING
DESIGN REVIEW WITH AN EOS ENGINEERS
AS ADDITIONAL BRACKETRY OR
WINDPOSTS MAY BE REQUIRED FOR
LARGER OPENINGS
Vertical stud
Lintel track
WINDOW MANUFACTURER TO ALLOW
ADDITIONAL TOLERANCE FOR MOVEMENT /
DEFLECTION ABOVE THE HEAD OF THE WINDOW
Title:
TYPICAL HARD FIXED LINTEL CONNECTION DETAIL (S & T)
STAGE:
Preliminary:
Approval:
Construction:
Drawn By:
Drawing No.
Scale:
n.t.s.
271
Revision:
Approved By:
Date:
A4
TOLERANCES:
Construction tolerances between frames
is -0mm +2mm. Frames are manufactured
and assembled to +0mm -2mm.
HE
AD
TR
AC
K
Head track fixed to Wind Post Double Stud each side
using 4.8mm dia. Tek screws (wafer heads) (EOS05)
Wind Post Double stud
HEAD FIXING
WIND POST DOUBLE STUD
MANUFACTURED OFFSITE
IN EOS FACTORY (100mm WIDE)
Wind Post Double Stud fixed to Wind Post Base Plate
using 4 No. 4.8mm dia. Tek screws (wafer heads)
(EOS05) each side
Wind Post Double stud
EOS base track securely fixed to concrete floor
using Tapcon fixings (EOS21) @ centres to suit wind
loading. Note:- fixing to be 50mm maximum from end of
track
BASE FIXING
SE
BA
TR
A
CK
Windpost Baseplate - EOS Engineer to
confirm project specific fixing requirements
NOTES
1. Fixing provided as required for windloading restraint.
2. Installer to confirm line and level of track base prior to fixing and report deviations greater than +/- 15mm.
3. Each track length to have fixing 50mm from each end.
Title:
TYPICAL PARAPET WIND POST CONNECTION DETAIL (S & T)
STAGE:
Preliminary:
Approval:
Construction:
Drawn By:
Drawing No.
Scale:
n.t.s.
272
Revision:
Approved By:
Date: