9th Edition vs 8th Edition Stds Revisions.xlsx
9th Edition IFI Inch Fastener Standards Book ‐ Published 2014 Highlights indicate standards that were updated since the 8th Edition TABLE OF CONTENTS Standards Revised since 8th Edition THREAD SECTION ASME B1.1 Unified Inch Screw Threads (UN and UNR Thread Form) ASME B1.2 Gages and Gaging for Unified Inch Screw Threads ASME B1.3 Screw Thread Gaging Systems for Acceptability: Inch and Metric Screw Threads (UN, UNR, UNJ, M, and MJ) IFI‐301 Gage Calibration Requirements and Procedures for Thread Gages BOLTS, STUDS AND THREADED ROD SECTION ASME B18.2.1 Square, Hex, Heavy Hex, and Askew Head Bolts and Hex, Heavy Hex, Hex Flange, Lobed Head, and Lag Screws IFI 182, Tap Bolts (New Standard) ASME B18.5 Round Head Bolts ASME B18.9 Plow Bolts ASME B18.10 Track Bolts and Nuts IFI 111 (ADD) ASME B18.31.2 Continuous and Double‐End Studs ASME B18.31.3 Threaded Rods ASME B18.31.5 Bent Bolts (Inch Series) IFI‐115 Flange 12‐Point Screws IFI‐148 Threaded Projection Weld Studs SAE J429 Mechanical and Material Requirements for Mechanical Fasteners ASTM A193/A193M Alloy Steel and Stainless Steel Bolting Materials for High Temperature Service ASTM A307 Carbon Steel Externally Threaded Standard Fasteners ASTM A320/A320M Alloy Steel Bolting Materials for Low Temperature Service ASTM A354 Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners ASTM A394 Steel Transmission Tower Bolts, Zinc Coated and Bare ASTM A449 Hex Cap Screw, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use ASTM A962 ASTM F468 Nonferrous Bolts, Hex Cap Screws, and Studs for General Use ASTM F593 Stainless Steel Bolts, Hex Cap Screws, and Studs ASTM F1554 Anchor Bolts, Steel, 36, 55 and 105‐ksi Yield Strength 2012 2013 2012 2012 2013 2014 2011 2013 2012b 2012 2011a 2011 2012 2013 IFI‐124 Test Procedure for the Performance of Nonmetallic Resistant Element Prevailing‐Torque Screws IFI‐125 Test Procedure for the Performance of Adhesive Coated Prevailing‐Torque Screws MIL‐DTL‐1222J General Specification for Studs, Bolts, Screws and Nuts for Applications Where a High Degree of Reliability is Required SOCKET SECTION ASME B18.3 Socket Cap, Shoulder, Set Screws, Hex, and Spline Keys ASTM A574 Alloy Steel Socket Head Cap Screws ASTM F835 Alloy Steel Socket Button and Flat Countersunk Head Cap Screws ASTM F837 Stainless Steel Socket Head Cap Screws www.indfast.org 2012 2013 2012 Standards ASTM F879 Stainless Steel Socket Button and Flat Countersunk Head Cap Screws ASTM F880 Stainless Steel Socket Set Screws ASTM F912 Alloy Steel Socket Set Screws STRUCTURAL FASTENERS SECTION ASME B18.2.6 Fasteners for Use in Structural Applications ASTM A325 Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength ASTM A490 Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile Strength ASTM F959 Compressible‐Washer‐Type Direct Tension Indicators for Use with Structural Fasteners ASTM F1852 Twist Off Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel, Heat Treated 120/105 ksi Minimum Tensile Strength ASTM F2280 “Twist Off” Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel, Heat Treated, 150 ksi Minimum Tensile Strength Revised since 8th Edition 2012 2012 2011 2012 2013 2011 2012 NUT SECTION ASME B18.2.2 Nuts for General Applications: Machine Screw Nuts, Hex, Square, Hex Flange, and Coupling Nuts ASME B18.6.9 Wing Nuts ASME B18.16.4 Serrated Hex Flange Locknuts: 90,000 psi ASME B18.16.6 Lock Nuts SAE J995 Mechanical and Material Requirements for Steel Nuts ASTM A194/A194M Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both ASTM A563 Carbon and Alloy Steel Nuts ASTM F467 Nonferrous Nuts for General Use ASTM F594 Stainless Steel Nuts IFI‐101 Torque‐Tension Requirements for Prevailing‐Torque Type Steel Hex and Hex Flange Nuts IFI‐155 Test Procedure for the Performance of Nonmetallic Resistant Element Prevailing‐Torque Nuts IFI‐160 Test Procedure for the Performance of Nuts with Pre‐Applied Adhesive Coated Threads SCREW SECTION ASME B18.6.1 Wood Screws ASME B18.6.2 Slotted Head Cap Screws ASME B18.6.3 Machine Screws, Tapping Screws, and Metallic Drive Screws ASME B18.6.8 Thumb Screws and Wing Screws ASME B18.13 Screw and Washer Assemblies — SEMS IFI‐113 Steel Self‐Drilling Tapping Screws ASTM C954 Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs from 0.033 in. (0.84 mm) to 0.112 in. (2.84 mm) in Thickness ASTM C1002 Steel Self‐Piercing Tapping Screws for the Application of Gypsum Panel Products ASTM C1513 Steel Tapping Screws for Cold‐Formed Steel Framing Connections WASHER SECTION ASME B18.21.1 Washers: Helical Spring‐Lock, Tooth Lock and Plain Washers ASTM F436 Hardened Steel Washers ASTM F2437 Carbon and Alloy Steel Compressible‐Washer‐Type Direct Tension Indicators for Use with Cap Screws, Bolts, Anchors, and Studs REMOVE www.indfast.org 2014 2012 2012a 2013 2011 2013 2011 2012 Standards RIVET SECTION ASME B18.1.1 Small Solid Rivets 7/16 In. Nominal Diameter and Smaller ASME B18.1.2 Large Rivets 1/2 In. Nominal Diameter and Larger ASME B18.7 General Purpose Semi‐Tubular Rivets, Full Tubular Rivets, Split Rivets and Rivet Caps IFI‐110 Glossary of Terms Relating to Blind Rivets IFI‐114 Break Mandrel Blind Rivets ADD IFI 116 IFI‐117 Pull Through Mandrel Blind Rivets IFI‐119 Structural Flush Break Pull Mandrel Self‐Plugging Blind Rivets IFI‐123 Drive Pin Blind Rivets IFI‐126 Break Mandrel Closed End Blind Rivets IFI‐130 Structural Splitting Self‐Plugging Pull Mandrel Blind Rivets IFI‐134 Multi‐Grip Flush Break Pull Mandrel Self‐Plugging Blind Rivets IFI‐135 Mechanical Testing of Blind Rivets IFI‐137 Inspection and Quality Assurance for General Purpose Blind Rivets PIN SECTION ASME B18.8.1 Clevis Pins and Cotter Pins ‐ New Revision ASME B18.8.2 Taper Pins, Dowel Pins, Straight Pins, Grooved Pins, and Spring Pins FINISHES SECTION ASTM B695 Coatings of Zinc Mechanically Deposited on Iron and Steel ASTM F1941 Electrodeposited Coatings on Threaded Fasteners ASTM F2329 Zinc Coating, Hot‐Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners QUALITY SECTION ASME B18.2.9 Gage and Gaging for Bolts and Screws ASME B18.18 Quality Assurance for Fasteners ASTM A370 ASTM F788/F788M Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series ASTM F812/F812M Surface Discontinuities of Nuts, Inch and Metric Series ASTM F1470 Standard Guide for Fastener Sampling for Specified Mechanical Properties and Performance Inspection IFI‐143 Test for Evaluating the Torque‐Tension Relationship on Both Externally and Internally Threaded Fasteners www.indfast.org Revised since 8th Edition 2013 2013 2012 2013 2013 2014 2013 2013 2012 2012
© Copyright 2025