1. technology and computing
2. technical support

Vacuum Consumables
PRO-VAC 150-LG-75
VACUUM BAGGING FILM
For low temperature cure up to 120°C
Description:
• A tough, puncture resistant co-extrusion of polyolefin and nylon based resins which are designed for use in the production of polyester/
vinylester resin infused components for the wind energy, marine and general composite industries.
• Limited sensitivity to low humidity levels which are often problematic to predominantly nylon based films as the lack of moisture can
reduce flexibility. This ensures consistent year long performance in all workshop environments.
• It is available in widths of up to 10 meters without seams. For larger more complex mouldings, such as boat decks, our 80 micron
version is recommended due to its added resistance to handling stresses and improved burst resistance.
Technical data:
Part number
PV150-LG-75
Colour
Light Green
Width
4m, 6m, 8m & 10m
Thickness
75μ +/-15%
ISO 4593
Elongation (break)
MD 340% +/- 15%
ASTM D882
TD 350% +/-15%
ASTM D882
MD 30 N/mm² +/-15%
ASTM D882
TD 25 N/mm² +/-15%
ASTM D882
Tensile (break)
Maximum use temp
120°C
Packaging and storage
Standard packaging is a strong bubble plastic; the rolls can be packaged in cardboard tubes if requested by customer.
This film contains a significant percentage of nylon which is hydrophobic therefore the film’s characteristics may change dependent on
workshop and storage environment. The lower the humidity, the stiffer the film will feel.
Store in original packaging
HF Industri & Marine ApS Gotlandsvej 6 5700 Svendborg Denmark
Phone: +45 62 20 13 12 • Fax: +45 62 20 14 77 • [email protected] • www.hfmarine.dk
All statements, technical information and recommendations, including storage, contained in this publication are based on tests believed to be reliable, but their accuracy
and/or completeness are not guaranteed. The user shall determine the suitability of this particular purpose and shall assume all risk and liability in connection herewith.
Vacuum Consumables
PRO-VAC 150-LG-80
VACUUM BAGGING FILM
For low temperature cure up to 120°C
Description:
• Modified structure to that of our standard product PRO-VAC 150, It has been designed for the moulding of very large, complicated
structures such as boat decks, where the film can be subjected to significant handling and high stresses when vacuum is applied.
• Limited sensitivity to low humidity levels which are often problematic to predominantly nylon based films, as lack of moisture can reduce
flexibility. This beneficial characteristic ensures consistent year long performance in all workshop environments.
• Available in both 12m and 16m wide without seams and can also be kitted into large formats by way of vacuum bag sealant tape.
Technical data:
Part number
PV150-LG-80
Colour
Light Green
Width
12m - 16m
Thickness
80μ +/-15%
ISO 4593
Elongation (break)
MD 330% +/- 15%
ASTM D882
TD 340% +/- 15%
ASTM D882
MD 33 N/mm² +/-15%
ASTM D882
TD 25 N/mm² +/-15%
ASTM D882
Tensile (break)
Maximum use temp
120°C
Packaging and storage
Standard packaging is a strong bubble plastic; the rolls can be packaged in cardboard tubes if requested by customer.
This film contains a significant percentage of nylon which is hydrophobic therefore the film’s characteristics may change dependant on
workshop and storage environment. The lower the humidity, the stiffer the film will feel.
Store in original packaging
HF Industri & Marine ApS Gotlandsvej 6 5700 Svendborg Denmark
Phone: +45 62 20 13 12 • Fax: +45 62 20 14 77 • [email protected] • www.hfmarine.dk
All statements, technical information and recommendations, including storage, contained in this publication are based on tests believed to be reliable, but their accuracy
and/or completeness are not guaranteed. The user shall determine the suitability of this particular purpose and shall assume all risk and liability in connection herewith.
Vacuum Consumables
PRO-VAC 100-LB-75
VACUUM BAGGING FILM
For all commonly used resin systems
Description:
• A tough, high temperature resistant co extruded nylon based material, which is designed for use in the production of advanced
composite structures such as wind turbine blades and nacelles, boat hulls and decks, plus other industrial structures.
• The film is ideal for use in both resin infusion and prepreg moulding applications and is resistant to all commonly used resin systems.
• Not suitable for use in autoclave processing of composites.
• The standard thickness is 75μ however other thicknesses are available to special order.
Technical data:
Part number
PV100-LB-75
Colour
Light blue
Width
3, 4, 6, 8 and 10.5 meters
Thickness
75μ +/- 15%
Elongation (break)
MD 382% +/- 15%
ASTM D882
TD 442% +/- 15%
ASTM D882
MD 54,4 N/mm² +/- 15%
ASTM D882
TD 52,1 N/mm² +/- 15%
ASTM D882
Tensile (break)
Maximum use temp
177°C
Packaging and storage
Standard packaging is a strong bubble plastic; the rolls can be packaged in cardboard tubes if requested by customer.
This film contains a significant percentage of nylon which is hydrophobic therefore the film’s characteristics may change dependant on
workshop and storage environment. The lower the humidity, the stiffer the film will feel.
Store in original packaging
HF Industri & Marine ApS Gotlandsvej 6 5700 Svendborg Denmark
Phone: +45 62 20 13 12 • Fax: +45 62 20 14 77 • [email protected] • www.hfmarine.dk
All statements, technical information and recommendations, including storage, contained in this publication are based on tests believed to be reliable, but their accuracy
and/or completeness are not guaranteed. The user shall determine the suitability of this particular purpose and shall assume all risk and liability in connection herewith.
Vacuum Consumables
PRO-VAC 200-O-50 & 200-G-75
VACUUM BAGGING FILM
For oven and autoclave usage
Description:
• A highly flexible multilayer nylon vacuum bagging films designed for processing of
advanced composite structures and laminated security glass.
• The film is ideal for use in both oven and autoclave cures, up to a maximum
recommended temperature of 170°C
• Key benefits of this film are its high elongation and flexibility.
Technical data (data is from 50μ thick film tests):
Part number
PV200-O-50 = 50μ thickness
PV200-G-75 = 75μ thickness
Colour
Orange
Width
1,5m and 2,2m in both 50 and 75 micron
Available in tube and ‘V’ sheet
Thickness
Elongation (break)
Tensile (break)
Maximum use temp
50μ +/-15% - designation PRO-VAC 200-O-50
ISO 4593
75μ +/-15% - designation PRO-VAC 200-O-75
ISO 4593
MD 410% +/-15%
ASTM D882
TD 414% +/-15%
ASTM D882
MD 56 N/mm² +/-15%
ASTM D882
TD 52 N/mm² +/-15%
ASTM D882
170°C
Packaging and storage
Standard packaging is a strong bubble plastic; the rolls can be packaged in cardboard tubes if requested by customer.
This film contains a significant percentage of nylon which is hydrophobic therefore the film’s characteristics may change dependant on
workshop and storage environment. The lower the humidity, the stiffer the film will feel.
Store in original packaging
HF Industri & Marine ApS Gotlandsvej 6 5700 Svendborg Denmark
Phone: +45 62 20 13 12 • Fax: +45 62 20 14 77 • [email protected] • www.hfmarine.dk
All statements, technical information and recommendations, including storage, contained in this publication are based on tests believed to be reliable, but their accuracy
and/or completeness are not guaranteed. The user shall determine the suitability of this particular purpose and shall assume all risk and liability in connection herewith.
Vacuum Consumables
PRO-VAC 250-G-75GL
VACUUM BAGGING FILM
For Glass lamination / autoclave
Description:
• This film has been developed for use in the production of laminated security glass.
• A tough but flexible nylon film it is ideal for use in either oven or autoclave processing methods of glass structures incorporating EVA
or PVB interlayer’s.
• The standard thickness is 75μ however other thicknesses are available to special order.
Technical data:
Part number
PV250-G-75GL
Colour
Green
Width
1,2m and 1,5m v-Sheet
Thickness
75μ +/-15%
ISO 4593
Elongation (break)
MD 374% +/-15%
ASTM D882
TD 395% +/-15%
ASTM D882
MD 61,1 N/mm² +/-15%
ASTM D882
TD 59,8 N/mm² +/-15%
ASTM D882
Tensile (break)
Maximum use temp
170°C
Packaging and storage
Standard packaging is a strong bubble plastic; the rolls can be packaged in cardboard tubes if requested by customer.
This film contains a significant percentage of nylon which is hydrophobic therefore the film’s characteristics may change dependant on
workshop and storage environment. The lower the humidity, the stiffer the film will feel.
Store in original packaging
HF Industri & Marine ApS Gotlandsvej 6 5700 Svendborg Denmark
Phone: +45 62 20 13 12 • Fax: +45 62 20 14 77 • [email protected] • www.hfmarine.dk
All statements, technical information and recommendations, including storage, contained in this publication are based on tests believed to be reliable, but their accuracy
and/or completeness are not guaranteed. The user shall determine the suitability of this particular purpose and shall assume all risk and liability in connection herewith.
Vacuum Consumables
PRO-VAC N85 NYLON PEEL PLY
Description:
• An 85 g/m² heat set and scoured nylon 6,6 peel ply fabric
• Designed for hand lamination and the vacuum infusion process
• Has a red tracer as a visible indicator to reducing the possibility of any peel ply being left on the laminate
• The fabric leaves a finish that can aid in the sanding or grinding of the laminate
• We do not recommend this product to be used with Phenolic resins
Technical data:
Part number
PVN85
Colour
Natural with red colour tracer
Width
0-1520mm
Length
100m/roll
Area Weight
85 g/m² ±3%
Maximum use temperature
180°C
*please note that the maximum use temperature is process specific, therefore we recommend that tests are performed on the peel ply
prior to use at elavated temperatures
Packaging and storage
It is recommended that the peel ply are stored in a cool and dry environment. Recommended temperature range of storage is between
10 ~ 30°C and relative humidity between 50 ~ 75%. The peel ply should remain in the packaging until just prior to use.
HF Industri & Marine ApS Gotlandsvej 6 5700 Svendborg Denmark
Phone: +45 62 20 13 12 • Fax: +45 62 20 14 77 • [email protected] • www.hfmarine.dk
All statements, technical information and recommendations, including storage, contained in this publication are based on tests believed to be reliable, but their accuracy
and/or completeness are not guaranteed. The user shall determine the suitability of this particular purpose and shall assume all risk and liability in connection herewith.
Vacuum Consumables
PRO-VAC P85 POLYESTER PEEL PLY
An 85g/m² heat set and scoured polyester peel ply fabric
Description:
• Designed for hand lamination and the vacuum infusion process
• Has a light red tracer as a visible indicator to reducing the possibility of any peel ply being left on the laminate
• The fabric leaves a finish that can aid in the sanding or grinding of the laminate
• This product can be used with Phenolic resins as well as all other standard resin systems but we do recommend that trails are
conducted to evaluate compatibility
Technical data:
Part number
PVP85
Colour
Natural with light red colour tracer
Width
0-1520mm
Length
100m / roll
Area Weight (g/m2)
85 g/m² ±3%
Maximum use temperature
180°C
*please note that the maximum use temperature is process specific, therefore we recommend that tests are performed on the peel ply
prior to use at elavated temperatures
Packaging and storage
It is recommended that the peel ply are stored in a cool and dry environment. Recommended temperature range of storage is between
10 ~ 30°C and relative humidity between 50 ~ 75%. The peel ply should remain in the packaging until just prior to use.
HF Industri & Marine ApS Gotlandsvej 6 5700 Svendborg Denmark
Phone: +45 62 20 13 12 • Fax: +45 62 20 14 77 • [email protected] • www.hfmarine.dk
All statements, technical information and recommendations, including storage, contained in this publication are based on tests believed to be reliable, but their accuracy
and/or completeness are not guaranteed. The user shall determine the suitability of this particular purpose and shall assume all risk and liability in connection herewith.
Vacuum Consumables
PRO-VAC 500-B-28 Release Film
For all commonly used resin systems
Description:
• Designed for use in resin infusion processing of advanced composite structures.
• It is compatible for use with a wide range of epoxy, polyester and vinylester resin
systems however we recommend small scale trials prior to committing to large infusion
mouldings.
• The films is available sky blue in colour with P31 (approx 6 holes per cm²) for vacuum
infusion and standard P3 perforation pattern for wet bagging and pre pregs.
• The perforations are hot needled to ensure even resin saturation is achieved throughout
the laminate.
• Other colours, thicknesses and perforation patterns may be possible dependant on
volume requirements.
Technical data:
Part number
PV500-B-28
Density
0.97
g/cm³
ASTM D1505 / ISO/R 1183
Thickness
28
µ
ISO 4593
Width
1500 nominal -0+2%
mm
Length
500 nominal -0+2%
m
Tensile strength at break
57,9± 10%
N/mm²
ASTM D882
Elongation at break
588± 10%
%
ASTM D882
Max use temperature
125
°C
ISO 306
Packaging and storage
Film is supplied in strong bubble plastic
Store in original packaging.
HF Industri & Marine ApS Gotlandsvej 6 5700 Svendborg Denmark
Phone: +45 62 20 13 12 • Fax: +45 62 20 14 77 • [email protected] • www.hfmarine.dk
All statements, technical information and recommendations, including storage, contained in this publication are based on tests believed to be reliable, but their accuracy
and/or completeness are not guaranteed. The user shall determine the suitability of this particular purpose and shall assume all risk and liability in connection herewith.
Vacuum Consumables
PRO-VAC 550-Y-50 Release Films
Release films instead of Peel ply.
Description:
• A mid temperature range, highly flexible polypropylene based release film.
• It is suitable for use with epoxy prepreg up to 150°C and may be used in resin infusion
applications with a wide range of resin systems however we recommend small scale
trials prior to committing to large infusion mouldings.
• The film is available yellow in colour with with P31 (approx 6 holes per cm²) for vacuum
infusion and standard P3 Perforation pattern for hand lamination and pre preg.
• The perforations are hot needled to ensure even resin saturation is achieved throughout
the laminate.
• Also available in 30 micron
Technical data:
Part number
PV550-Y-50
Density
0.89-0.91
g/cm³
ASTM D1505 / ISO/R 1183
Thickness
50
µ
ISO 4593
Width
1500 nominal -0+2%
mm
Length
250 nominal -0+2%
m
Tensile strength at break
35± 10%
N/mm²
ASTM D882
Elongation at break
500± 10%
%
ASTM D882
Max use temperature
153
°C
ISO 306
Packaging and storage
Film is supplied in strong bubble plastic
Store in original packaging.
HF Industri & Marine ApS Gotlandsvej 6 5700 Svendborg Denmark
Phone: +45 62 20 13 12 • Fax: +45 62 20 14 77 • [email protected] • www.hfmarine.dk
All statements, technical information and recommendations, including storage, contained in this publication are based on tests believed to be reliable, but their accuracy
and/or completeness are not guaranteed. The user shall determine the suitability of this particular purpose and shall assume all risk and liability in connection herewith.
Vacuum Consumables
PRO-VAC B1141
vacuum bagging sealant tape
Low to medium temperature sealant tape
Description:
• Recommended for use in vacuum infusion, wet lay-up bagging and bag to bag (envelope bagging) processing.
• Compatible with most vacuum films and tool surfaces but pre-production trials are advisable.
• We recommend that the tape is removed at room temperature.
Technical data:
Max use temperature
150°C - bag to tool and bag to bag
colour
Black
Standard roll sizes
PVB1141
3mm x 12mm x 15m
Standard packaging
PVB1141
20 rolls per box - 36 boxes per pallet
Packaging and storage
Store in original and unopened packaging and protected from humidity
Store at a maximum temperature of 30°C in a ventilated environment
Material has a 12 month shelf life from date of manufacture
Store flat with a maximum of 4 boxes stacked
HF Industri & Marine ApS Gotlandsvej 6 5700 Svendborg Denmark
Phone: +45 62 20 13 12 • Fax: +45 62 20 14 77 • [email protected] • www.hfmarine.dk
All statements, technical information and recommendations, including storage, contained in this publication are based on tests believed to be reliable, but their accuracy
and/or completeness are not guaranteed. The user shall determine the suitability of this particular purpose and shall assume all risk and liability in connection herewith.
Vacuum Consumables
PRO-VAC 1G POLYESTER
Pressure sensitive tape
Description:
• An economical pressure sensitive silicone adhesive polyester tape intented for general workshop use.
• Easily removed following oven or autoclave processing.
• Coloured green for easy identification on the mould
Technical data:
Part number
PV1G
Widths
25mm and 50mm
Roll length
66m
Maximum use temp
180°C
Film carrier
Polyester
Adhesive type
Silicone
Colour
Blue
Total thickness
62μ
Adhesion to steel
400 cN/cm
Packaging and storage
The tape can be stored for maximum 6 months from the date of production in dry conditions and in its original packaging. The material
should be protected from extreme temperatures and direct sunlight. Once removed from its original packaging, the tape should be
protected from dust and other impurities. Keep the rolls in horizontal position.
HF Industri & Marine ApS Gotlandsvej 6 5700 Svendborg Denmark
Phone: +45 62 20 13 12 • Fax: +45 62 20 14 77 • [email protected] • www.hfmarine.dk
All statements, technical information and recommendations, including storage, contained in this publication are based on tests believed to be reliable, but their accuracy
and/or completeness are not guaranteed. The user shall determine the suitability of this particular purpose and shall assume all risk and liability in connection herewith.
Vacuum Consumables
PRO-FIX SPRAY ADHESIVE
Description:
• Designed for bonding of dry glass, carbon and aramid fibers for composite structure preparation
• Can be also used for fixing core materials – foams and balsa – as well as vacuum consumables like peel ply and breather fabric
• PRO-FIX is only available in 500ml cans
User guide
• Make sure the surfaces which are to be bonded are clean and dry, shake the can well and
spray from a distance of 25 cm, hold the can vertically and spray an even layer of adhesive;
it must not appear as being wet if it does then move further away from the surface.
• When spraying the adhesive keep a fluid movement with the hand to avoid spraying too
much adhesive in one place
• After each application purge the nozzle by spraying the can upside down
• To achieving the optimum bond both surfaces must be sprayed with adhesive, wait around
1 minute to allow the solvent to evaporate then press the surfaces together
Packaging and storage
Store in temperatures below 50°C and do not expose to direct sun light, flames or source of ignition
Packaged in boxes of 12 cans and pallets of 50 boxes (600 cans)
For more information please refer to the PRO-FIX MSDS and when handling products of this nature the user must always conform to
their company’s Health and Safety regulations and guidelines.
HF Industri & Marine ApS Gotlandsvej 6 5700 Svendborg Denmark
Phone: +45 62 20 13 12 • Fax: +45 62 20 14 77 • [email protected] • www.hfmarine.dk
All statements, technical information and recommendations, including storage, contained in this publication are based on tests believed to be reliable, but their accuracy
and/or completeness are not guaranteed. The user shall determine the suitability of this particular purpose and shall assume all risk and liability in connection herewith.
Vacuum Consumables
PRO-VAC BM230P FLOW MEDIA
Description:
• Extruded grid mesh
• Recommened for flat panels and single curvature moulds due to the stiffness of the material
• Compatiable with all standard epoxy, polyester and vinylester resin systems
• A faster flowing mesh compared to the standard knitted types
Technical data:
Part number
PVBM230P
Colour
Green
Density
230 g/m² ±5%
Nominal Temp Resistant
120°C
Mesh Size
1.8 X 1.8mm
Thickness
0.75 ~ 0.82mm
Packaging and storage
Plastic film inside, 50M/Roll.
It is recommended that the products are stored in a cool and dry environment.
The mesh should remain in the packaging until just prior to use.
HF Industri & Marine ApS Gotlandsvej 6 5700 Svendborg Denmark
Phone: +45 62 20 13 12 • Fax: +45 62 20 14 77 • [email protected] • www.hfmarine.dk
All statements, technical information and recommendations, including storage, contained in this publication are based on tests believed to be reliable, but their accuracy
and/or completeness are not guaranteed. The user shall determine the suitability of this particular purpose and shall assume all risk and liability in connection herewith.
Vacuum Consumables
PRO-VAC KM160E1 FLOW MEDIA
Description:
• 3D Knitted mesh
• Compatiable with all standard epoxy, polyester and vinylester resin systems
• Highly drapable so can be used on complex moulds
• Can also be used as a reuasble breather for debulking at room temperature
• Available up to 2m wide
Technical data:
Part number
PVKM160E1
Colour
Black
Density
160 g/m²±5%
Nominal Temp Resistant
120°C
Thickness
1.0 mm
Elongation At break
500%
Tensile Strength
23 N/mm²
Packaging and storage
Plastic film inside, 100M/Roll.
It is recommended that the products are stored in a cool and dry environment.
The mesh should remain in the packaging until just prior to use.
HF Industri & Marine ApS Gotlandsvej 6 5700 Svendborg Denmark
Phone: +45 62 20 13 12 • Fax: +45 62 20 14 77 • [email protected] • www.hfmarine.dk
All statements, technical information and recommendations, including storage, contained in this publication are based on tests believed to be reliable, but their accuracy
and/or completeness are not guaranteed. The user shall determine the suitability of this particular purpose and shall assume all risk and liability in connection herewith.
Vacuum Consumables
PRO-VAC B-150 BREATHER
Description:
• Medium weight non woven PET breather/bleeder
• Good drapability and works well with single curvature and complex parts
• Good for all low pressure production process and can be used in multiply layers to
increase the flow capacity.
Technical data:
Part number
PVB-150
Mass per unit area
150
g/m²
ISO 9073-1
Thickness at 2 kPa
1,8
mm
ISO 9863-1
Tensile strength
225 / 290
N
ISO 9073-3
Elongation at 100N
40 / 50
%
ISO 9073-3
Melting point
250
°C
Maximum use temperature
210
°C
Standard roll length
95
m
Standard roll width
1,52
m
Composition
100% PET
*rolls can be slit to specific widths upon request (minimum order will apply)
Packaging and storage
Store in original packaging
HF Industri & Marine ApS Gotlandsvej 6 5700 Svendborg Denmark
Phone: +45 62 20 13 12 • Fax: +45 62 20 14 77 • [email protected] • www.hfmarine.dk
All statements, technical information and recommendations, including storage, contained in this publication are based on tests believed to be reliable, but their accuracy
and/or completeness are not guaranteed. The user shall determine the suitability of this particular purpose and shall assume all risk and liability in connection herewith.
Vacuum Consumables
PRO-VAC vacuum ancillaries
A full range of interconnecting vacuum infusion hoses,
valves, omega profiles and inlet block
The PVINB-16 inlet block has been specially developed to not only to self seal with the PVL connectors but also to fit with the PVO omega profiles.
To decrease the complexity of vacuum bagging and bridging around the inlet points.
PRO-VAC INLET BLOCK
Technical data:
Part number
Material
i/d (mm)
height (mm)
max temp
PVINB-16
PP
16 +/- 0.5
35
100°C
PRO-VAC L-CONNECTOR FOR INLET BLOCK
Technical data:
Part number
Material
o/d
max temp
PVL-12
PE
12
100°C
PVL-18
PE
18
100°C
PRO-VAC OMEGA CHANNEL
Technical data:
Part number
Material
I/d (mm)
max temp
length (m)
PVO-16
PVC
16
60°C
4
PRO-VAC INFUSION VALVES
Technical data:
Part number
Material
o/d
max temp
PVV-10 (double O-ring)
PE
10
100°C
PVV-12 (double O-ring)
PE
12
100°C
PVV-18 (double O-ring)
PE
18
100°C
HF Industri & Marine ApS Gotlandsvej 6 5700 Svendborg Denmark
Phone: +45 62 20 13 12 • Fax: +45 62 20 14 77 • [email protected] • www.hfmarine.dk
All statements, technical information and recommendations, including storage, contained in this publication are based on tests believed to be reliable, but their accuracy
and/or completeness are not guaranteed. The user shall determine the suitability of this particular purpose and shall assume all risk and liability in connection herewith.
Vacuum Consumables
PRO-VAC T-INFUSION TAPS
Technical data:
Part number
Material
o/d
max temp
PVT-10
PE
10
100°C
PVT-12
PE
12
100°C
PVT-18
PE
18
100°C
PRO-VAC SPRIAL WRAP
Technical data:
Part number
Material
I/d (mm)
thickness (mm)
max temp
length (m)
PVSW-10
PE
10 +/- 0.5
1.0 +/- 0.1
100°C
100
PVSW-12
PE
12+/- 0.5
1.0 +/- 0.1
100°C
100
PVSW-18
PE
18 +/- 0.5
1.5 +/- 0.1
100°C
100
PRO-VAC INFUSION HOSE
Technical data:
Part number
Material
I/d (mm)
thickness (mm)
max temp
length (m)
PVI-10
PE
10 +/- 0.5
1.0 +/- 0.1
100°C
100
PVI-12
PE
12+/- 0.5
1.0 +/- 0.1
100°C
100
PRO-VAC REINFORCED HOSES
Technical data:
Part number
Material
I/d (mm) thickness (mm)
max temp length (m)
PV-RHOSE-13
fabric reinforced PVC
13
5
60°C
100
PV-RHOSE-19
fabric reinforced PVC
19
5
60°C
50
2.5
60°C
50
PV-SRHOSE-18 PVC spiral reinforced PVC 18
Packaging and storage
Store in original packaging.
All ancillaries are supplied in separate bags.
HF Industri & Marine ApS Gotlandsvej 6 5700 Svendborg Denmark
Phone: +45 62 20 13 12 • Fax: +45 62 20 14 77 • [email protected] • www.hfmarine.dk
All statements, technical information and recommendations, including storage, contained in this publication are based on tests believed to be reliable, but their accuracy
and/or completeness are not guaranteed. The user shall determine the suitability of this particular purpose and shall assume all risk and liability in connection herewith.
Vacuum Consumables
PRO-VAC HFVL
High flow vacuum line
Description:
• PRO-VAC HFVL is acost effectivehigh quality micro porous vacuum line which allows air to flow consistently through itself as well as
acting as a resin barrier throughout the vacuum infusion process.
• PRO-VAC HFVL consists of a combination of products that have been brought together to make a user friendly and easy hand able
robust product.
• Adhesive was chosen as the sealing agent between the layers because during our extensive testing of the PRO-VAC HFVL we found
that this method of sealing (instead of welding) produced a much higher quality and durable seal.
Process benefits
• Allows for less complex infusion strategies therefore can reducelabour time
•Excellent vacuum compaction throughout the process resulting in a better quality
laminate
• Small footprint on the laminate surface
• Releases easily from all know resin systems
• Can be used as a sacrificial vacuum line to initiate vacuum once the laminate is wet out
• Can be used as a single point vacuum outlet to combat troublesome dry areas in already
established process
• Does not contain resin after cure therefore no issues with marking due to exotherm
•Reduced amount of resin required for the process because no resin is wasted in the
vacuum lines and catch pots
Specification
Widths: 150mm and 300mm wide
*Special widths may be ordered contact our technical staff for details
Length: 100m long rolls
Technical details and training
For further technical information and training please contact our technical staff to organize a product demonstration.
Packaging and storage
Store in original packaging at room temperature (22 °C).
Shelf life is 8 months
HF Industri & Marine ApS Gotlandsvej 6 5700 Svendborg Denmark
Phone: +45 62 20 13 12 • Fax: +45 62 20 14 77 • [email protected] • www.hfmarine.dk
All statements, technical information and recommendations, including storage, contained in this publication are based on tests believed to be reliable, but their accuracy
and/or completeness are not guaranteed. The user shall determine the suitability of this particular purpose and shall assume all risk and liability in connection herewith.
Vacuum Consumables
PRO-VAC MLR-5
Reinforced teflon mould release
Description:
• High quality self-adhesive Teflon coated glass mould release for composite processing applications
• Adheres to composite and metal tools as well as wooden moulds and plugs
• The adhesive system is pressure sensitive therefore is stable throughout vacuum and autoclave curing
• Recommended for use on flat or single curvature surfaces, can be joined using a butt joint
Technical data:
Part number
PV MLR-5
Reinforcement
woven glass
Coating
PTFE
Ptfe content
58%
Adhesive
Silicone
Nominal adhesive weight
255 gsm
Nominal adhesive thickness
0,125mm
Nominal total thickness
0,175mm
Adhesion
5,4 N/cm
Max use temperature
260 deg c
Width
1000mm
Packaging and storage
Store in original packing at room temperature (22 °C)
Shelf life of 8 months from date of manufacture
HF Industri & Marine ApS Gotlandsvej 6 5700 Svendborg Denmark
Phone: +45 62 20 13 12 • Fax: +45 62 20 14 77 • [email protected] • www.hfmarine.dk
All statements, technical information and recommendations, including storage, contained in this publication are based on tests believed to be reliable, but their accuracy
and/or completeness are not guaranteed. The user shall determine the suitability of this particular purpose and shall assume all risk and liability in connection herewith.
Vacuum Consumables
PRO-VAC B1191
next generation vacuum bagging sealant tape
Low to medium temperature sealant tape
Description:
• Improved level of tack and hand ability
• Tape preforms best at room temperature (+ 20 0 C), if the tape is too cold the tack levels will be dramatically reduced
• Recommended for use in vacuum infusion, wet lay-up bagging and bag to bag (envelope bagging) processing
• Compatible with most vacuum films and tool surfaces but pre-production trials are advisable
• We recommend that the tape is removed from the mould at room temperature
Technical data:
Max use temperature
150 0 C - bag to tool and bag to bag
Colour
Black
Standard roll size
PRO-VAC B1191
3mm x 12mm x 15m
Standard packaging
PRO-VAC B1191
22 rolls per box – 50 boxes per pallet
*The tape is also available in grey, as a double strip profile and a bead in various diameters
Packaging and storage
Store in original and unopened packaging and protected from humidity
Store at a maximum temperature of 30°C in a ventilated environment
Material has a 12 month shelf life from date of manufacture
Store flat with a maximum of 5 boxes stacked
HF Industri & Marine ApS Gotlandsvej 6 5700 Svendborg Denmark
Phone: +45 62 20 13 12 • Fax: +45 62 20 14 77 • [email protected] • www.hfmarine.dk
All statements, technical information and recommendations, including storage, contained in this publication are based on tests believed to be reliable, but their accuracy
and/or completeness are not guaranteed. The user shall determine the suitability of this particular purpose and shall assume all risk and liability in connection herewith.