SubDrive Inline 1100 Brochure

INLINE 1100
CONSTANT PRESSURE SYSTEM
The SubDrive Inline 1100 provides
constant pressure for both
private wells and municipal/city
water systems.
franklinwater.com
SUBDRIVE INLINE 1100
APPLICATIONS
ƒƒ Boosted and constant water pressure from water storage/cistern systems
ƒƒ Homes (in both private and municipal applications)
ƒƒ General pressure boosting
ƒƒ Sprinkler systems
ƒƒ Farming and commercial wash down systems
FEATURES
ƒƒ Pump, motor, drive, and pressure switch in one box as a packaged system
ƒƒ Small and compact design fits into small areas, even between floor joists
ƒƒ Stainless steel construction for years of operation
ƒƒ Simple and easy installation with step-by-step illustrated instructions
ƒƒ Integrated motor design allows water to flow around it for quiet and cool operation
ƒƒ NEMA 4 (IP56) electronics enclosure
ƒƒ Multiple mounting configurations allow for the unit to be installed where you need it, whether
horizontal, vertical, or even upside down
ƒƒ Built-in system protections guard the Inline unit from many common failure modes including surge
protection, voltage underload, locked pump, open circuit, short circuit, and overheated controller.
ƒƒ Product power rating: 1.2 hp, 0.9 kW
ƒƒ Shipping weight: 50 lbs, 22.7 kg
ORDERING INFORMATION
Model Description
Order No.
25SDIL1100N4* (Complete pump w/NPT)
90401101
25SDIL1100N4-B* (Complete pump w/BSP)
90401102
Electronic Drive Assembly
305707901
Pump & Motor Assembly w/NPT
305707902
Pump & Motor Assembly w/BSP
305707911
Mounting Feet
305707903
Pressure Switch
305707906
Pressure Tank (2 gallon)
305707910
Fastener Kit
305707904
Pressure Switch Cable
305707905
Overpressure Switch**
305707909
Overpressure Switch Cable**
305707908
Overpressure Switch & Cable Combo**
305707912
Thermostat Kit
305707917
* Includes pump, motor, drive, pressure switch, and all cables.
** Overpressure switch is sold as an accessory and is not required for normal operation.
Input Voltage
Input Phase
230
Single
N/A
N/A
SUBDRIVE INLINE 1100
PERFORMANCE
m
ft
180
INCREMENTAL PRESSURE INCREASE
50
160
70
140
60
40
120
30
psi
80
100
50
40
80
20
10
RECOMMENDED OPERATING RANGE
30
60
40
0
20
20
10
0
0
0
5
0
20
0
1
10
15
40
2
20
60
3
25
80
4
30
35
100
5
6
120
7
40
140
8
45
160
9
10
50 gpm
180
lpm
11
m3/h
FLOW
NOTE: Running outside of ‘Recommended Operating Range’ for short periods of time is permissible.
SYSTEM COMPONENTS
Water Flow
NEMA 4 (IP56) Drive
Thermostat
Secure Power Cord
1-1/4" NPT Outlet
1-1/4" NPT Inlet
Stainless Steel Impellers
Sealed Motor
DIMENSIONS
18.85
[478,7]
TO THERMOSTAT
18.84
[478,5]
3.45
[87,7]
9.31
[236,4]
8.00
[203,2]
7.00
[177,8]
5.72
[145,2]
INPUT
POWER
2.92
[74,1]
6.65
[168,9]
DISCHARGE
SEE TABLE
FOR SIZE
SUCTION
SEE TABLE
FOR SIZE
1.50
[38,1]
10.43
[265]
17.32
[439,9]
TYPICAL INSTALLATION
5 FEET OR LESS
2 GALLON
TANK
POWER
INLINE SYSTEM
BALL
VALVE
UNION
COUPLING
FLOW
UNION
COUPLING
CHECK
VALVE
OPTIONAL BYPASS
BALL
VALVE
PRESSURE
GAUGE
PRESSURE
RELIEF
VALVE
WATER SUPPLY
*CHECK
VALVE
PRESSURE
SWITCH
PRESSURE
SHUT-OFF
SWITCH
(OPTIONAL)
BALL
VALVE
TO HOME
(DISCHARGE INTO DRAIN
RATED FOR MAX PUMP
OUTPUT AT RELIEF PRESSURE)
CHECK
VALVE
NOTE: These optional components are shown in a typical installation diagram. They should be used at the installer’s discretion as required for particular applications.
* When connected to a municipal system, if the plumbing does not have a backflow prevention device, a check valve is required on the incoming water supply line.
If installed on a cistern, the check valve should be passive or be eliminated.
franklinwater.com
M2179 06-15