1. art and entertainment
2. music
3. musical instruments
4. drums

can be found at www.pacificdrums.com
of Drum Workshop, Inc. C 2007 Drum Workshop, Inc.
stered trademark of Drum Workshop, Inc.
X7 SERIES DRUMSETS
ASSEMBLY AND SET-UP GUIDE
1-YEAR LIMITED WARRANTY
Congratulations on your purchase of this Pacific Drum Kit. The following directions
are a step-by-step guide to get you playing your new drums as quickly as possible.
The only tool you need is the drum key that is supplied with your kit.
Additional tips and information can be found at www.pacificdrums.com
PACIFIC DRUMS & PERCUSSION 1 YEAR LIMITED WARRANTY
This warranty protects the original retail purchaser, only. If a covered product or component fails due to a manufacturing or material
defect, Pacific will repair or replace the product at no charge. To obtain warranty service, return the product to your authorized Pacific
Drums dealer along with your original proof of purchase. In the case that the dealer is unable to correct a warranty defect, the dealer
will then contact Pacific for further instructions and to obtain a Return Authorization (RA) number. No shipments will be accepted
without an RA number. Any and all shipping charges are the responsibility of the purchaser.
This warranty does not apply to 1) drums purchased from a source other than an authorized Pacific Drum dealer, 2) any owner other
than the original purchaser, 3) defects caused by neglect, moisture, extreme temperatures, handling, shipping or use under normal
playing conditions, 4) finishes, 5) alterations made after the product leaves the factory and 6) drumhead. Pacific drums and
percussion shall not be liable for incidental, consequential or other damages that may arise as a result of or related to any defect or
failure of this product. This warranty gives you specific legal rights. You may also have other rights, which vary from state to state.
Component
Length of Coverage
drum shells
l year
drum finishes
1 year
drum hardware
1 year
OPTIONAL HARDWARE
OPTIONAL RACK SYSTEM
Bass Drum Assembly
Package Contents
D
C
B
A
900 HARDWARE HEAVY-DUTY
A
B
2.
E
1.
F
G
H
4.
I
M
6.
K
J
7.
L
O
N
P
Q
V
U
T
S
R
5.
3.
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
8.
Drum key (1)
Bass Drum Heads (2)
(One Clear Batter & One Black Logo Resonant)
1.Drum
TS900
Tom Stand
Bass
HoopsDouble
(2)
18X22" Bass Drum Shell (1)
Bass Drum Pillow (1)
2. CB900 Straight/Boom Cymbal
Claw Hooks (16)
Stand
Bass
Drum Tension Rods (16 + 2 spares)
Metal Washers (48 + 4 spares)
Lug3.
Receivers
(6 Snare
spares) Stand
SS900
Smaller Tension Rods For Toms (32 +2 spares)
Bass Drum Mount Double Tom Holder (1)
4. AC991
C900Tom
Straight
Cymbal Stand
Single
Clamp (1)
Floor Tom Drum Legs (6 - 2 Set Of 3 Legs Each)
7X8"
Tom (13-Leg
- Assembled)
5.Tom
HH900
Hi-Hat
8X10" Tom Tom (1 - Assembled)
9X12" Tom Tom (1 - Assembled)
6. Snare
HH920
Rotating
2-Leg Hi-Hat
5X14"
Drum
(1 - Assembled)
14" Floor Tom Drum Clear Heads (2)
12X14"
Floor Tom Drum
(1)Sparkle/Zebra
7. DT900Z
White
16" Floor Tom Drum Clear Heads (2)
Throne
14X16" Floor Tom Drum (1)
PDP Drum Sticks (2)
8. DT900S Black Sparkle Throne
Bass Drum Assembly
1: Set the bass drum shell D on the side with the spurs (legs)
Main Rack Package Step
(PDSRPK05)
G
towards the top. Place the black “PDP” logo head B over the shell. Center
the logo underneath the BDM (Bass Drum Mount Receiver) located on
the top of the bass drum.
H
F
Step 2: Place one of the bass drum hoops C over the bass drum head
with the flat side of the hoop against the head.
C
B
Step 3: Slide 8 metal washers H onto 8 longer tension rods G . Then slide
the tension rod through 8 claw hooks F .
D
Step 4: Position each claw hook over the bass drum hoop and thread the
tension rods into the lugs around the shell. Tighten by hand only. (You
will fully tighten and tune the drum later.)
Step 5: Set the shell right-side-up.
Bass Drum Assembly
BDM Receiver
Rack Accessories
StepsHARDWARE
to remove contents
from
Steps to remove contents from
800
MEDIUM-DUTY
Box 1 of 2
Box 2 of 2
1. CB800 Straight/Boom Cymbal Stand
1. Before removing anything from box 1 of 2, place the box in a
2. CS800
Straight
Cymbal
location
where you
will be able
removeStand
the contents of the
boxes.
2. Remove
the topTractor
packet that
holds the drum heads for the
3. DT820X
Throne
bass drum B and the two floor tom drums. R & T
C
3. Remove
the Bass Drum
hoop.
4. HH800-01
3-Leg
Hi-Hat
4. Beneath the hoop, you will find fully assembled (12") P and
(10")5.O SS800
tom drums.
Snare Stand
5. Remove all excess packing around the tom drums to ensure
easy removal.
6. HH820 2-Leg Hi-Hat
6. Remove the top tom drum P and then the bottom tom
drum. O Place drums on a smooth and sturdy surface to prevent
7. DT800-04
damage
your drums. Standard Throne
7. Remove the unassembled floor tom U and place the drum on
a smooth and sturdy surface to prevent damage to your drum.
8. Remove the cardboard ring around the bass drum shell D by
grabbing the cut-out handle and lifting upward.
9. Remove the bass drum pillow E ,positioned along the side of
the bass drum shell. D
10. With both hands, grasp each side of the bass drum shell D ;
pull the bass drum shell upward to remove from the packaging.
Place the drum shell on a smooth and sturdy surface to prevent
damage to your drum.
11. Once the bass drum shell D is removed from the box, lift up
the bottom cardboard insert to find the second bass drum
hoop. C
12. Take this time to line up all the drums accordingly by size,
from smallest to largest.
13. Place the two large bass drum heads B (clear/black) on top
of your bass drum shell.
14. Take the two (16") T clear drum heads and place them on
top of the unassembled floor tom drum. U
1.
2.
15. Remove the top rectangular box containing the six legs for
the floor toms. M
16. Place three legs M next to the (16") floor tom U from the
first box.The other three legs will be placed next to the other
floor tom once removed from this box.
17. Next you will find a long rectangular box that includes
drumsticks V , claw hooks F , washers H , and tension rods
G & J that will be used during assembly.
18. Remove the box with the snare drum. Q Place the snare
drum on a smooth and sturdy surface to prevent damage to
your drum.
19. Remove and open the styrofoam box and place the smaller
AC991 tom clamp L aside. Place the larger bass drummounted double tom holder K near the bass drum. D
20. Under the snare drum box, you will find a smaller box with
another tom drum. Remove the drum N from the box
and place the drum on a smooth and sturdy surface to prevent
damage to your drum.
21. Before removing the last drum from this packaging, be
sure to remove the styrofoam blocks to assure easy removal
from the
box.
22. Remove the last floor tom drum S from the box just as you
did earlier
for the bass
drum.
1. HH700
3-Leg
Hi-Hat
23.Take this time to line up all the drums accordingly by size
from smallest to largest as you did earlier.
2. CB700 Straight/Boom Cymbal Stand
24. Take the three legs M and place them next to the floor tom
drum S just removed from the second box.
3. SS700
Snare
Stand
25. Take
the last two
remaining
(14") clear drum heads R and
place them on top of the floor tom drum S just removed from
4.
CS700
Straight
Cymbal
Stand
the second box.
3.
4.
5.
6.
7.
700 HARDWARE LIGHTWEIGHT
4.
1.
15
2.
3.
5.
5. DT700 Throne
Step 6: Remove the plastic backing from the self-adhesive Velcro tape on
E . Attach the pillow
the bass Rack
drum pillowPackage
inside the bottom of the shell
Combo
(PDSRCOMBO1)
with the adhesive. The pillow should be positioned towards the back of
the shell so that it will lightly touch the batter (clear) head when
assembled.
A. PDCH1012 Closed Hi-Hat Arm Step 7: Turn the drum on its sideB.
(black head down) with the pillow
B. PDDB799 DogBone™ w/ Cymbal
Armthe top. Place the clear batter head B over the shell. Center the
towards
logo underneath the BDM (Bass Drum MountD.
Receiver) located on the
C. PDDB798 DogBone™
top of the bass drum.
D. PDCB0934 Cymbal Arm (Standard)
A.
E.
D
E
C B
C (Short)
PDCB0934S
Cymbal
Arm
C.
Step 8: Repeat steps 2 through 4 for the batter head.
PDCB0978 Cymbal Boom Arm (7/8”)
E. DWSMRKDRKY Hi-Torque DrumStep
key9: Set the shell right-side-up.
F. Step
DWSMRKFEET
(2-pack)
10: By looseningRubber
the wing Feet
nut, angle
the spurs so they face
Bass Drum Assembly
G. slightly
PDSRC15V
Clamp
towards 1.5”-V
the front of
the bass drum.
G
F
H. DWSMRKC15A 1.5”-V Angle Adjustable Clamp
F.
D
11: Loosen the spur
legs with T-Leg
the drum
key Aand lower the legs
I. Step
DWSMRKC15T
1.5”-1.5”
Clamp
C
so that the front of the bass drum is lifted about one inch off the
J. ground.
DWSMRKC15K
1.5”-1.5” Rack Clamp
Tighten the spurs.
K. DWSMRKC15SV 1.5”-V Angle Adjustable Stacker
NOTE:
For convenience, you may now want to tune your bass drum G.
Clamp
H.
I.
J.
attaching the tom1.5”
and pedal.
Please refer
to page
for tuning
L. before
DWSMRKC15AC
Accessory
Clamp
w/5 Eyebolt
guidelines.
M. DWSMRKML15 1.5” Hinged Memory Lock
DWSMRKML10
1” Hinged
Memory
10"
and 12"
TomLock
Toms
N. DWSMRKTTCA 1.5”-3/4” Tube Top Cymbal
K.
L.
M. N.
Spurs
Adapter
B
Step
1: Insert the Double tom holder K into the BDM receiver on top
O. ofDWSMRKC15AS
1.5”-1.5” Hinged Angle
the bass drum.
Stacker Clamp
2: Loosen the wing screw on the bracket of the (10") tom tom O
10" and 12" Q.
Tom Toms
P. Step
DWSMRKC15VA
1.5”-V Accessory Clamp
and slide it over the right tom arm on the left (from a right-handed
K
Q. drummer’s
DWSMRKC15S
1.5”-1.5”
Angle
Adjustable
O.
P.
R.
P
perspective behind the kit - reverse if you play leftO
StackerTake
Clamp
handed).
care that the tom arm does not touch the tom shell.
the wing 10.5
screw on
the Tom
tom bracket.
R. Tighten
DWSMTA10
mm
Arm w/ Memory Lock
S. DWCPRKB42C 42” Stainless Steel Curved Bar
Step 3: Loosen the wing screw on the bracket of the (12") tom tom P
BDM Receiver
T. Position
DWCPRKB24C
Steel
Curved Bar
it on the tom24”
arm Stainless
(reverse if you
play left-handed).
Take care
DWCPRKB12S
12”
Steel
that
the tom arm does
notStainless
touch the tom
shell. Straight
Tighten the Bar
wing screw
the tom bracket. 24” Stainless Steel Straight Bar
U. on
DWCPRKB24S
S.
T.
D
V. DWCPRKB36S 36” Stainless Steel Straight Bar
U.
NOTE: Don’t worry about the precise placement of the drums at this
W.point.
DWCPRKB42S
42”
Stainless
Steel
Straight
Bar
V.
You will arrange them all later.
DWCPRKB72S 72” Stainless Steel Straight Bar W.
DWSMRKCAPS Tube End Caps (2-pack)
PDSRNPLV Pacific Nameplate Bar Level
62
8" Tom Tom and Cymbal Stand
8" Tom Tom and Cymbal Stand
Step 1: Spread open the legs on the bottom section of the cymbal
stand* and tighten the wing screw. Slide the upper section of the cymbal
stand* into the base section and tighten that wing screw.
Wing nut
Items marked with (*) are an optional purchase from your authorized PDP Drum Dealer
Wing screw
Snare Drum and Snare Stand
Step 1: Spread open the legs on the bottom section of the snare
stand* and tighten the wing screw. Slide the upper section of the snare
stand* into the base section and tighten that wing screw.
Knob for Size Adjustment
Bass Drum Pedal
Step 1: Remove the rubber band from the radius rod of the bass drum
pedal* and insert the radius rod into the holes at the bottom of the
pedal’s base.
Beater
Step 2: Rotate the hex shaft counter clockwise until the spring hub is
at the 6:00 position and the chain is wrapped around the cam. Stretch
the spring up onto the rocker hub.
Step 3: Attach the pedal to the bottom of the bass drum hoop on the
clear batter head side using the drum screw activated clamp on the
side of the pedal.
Hi Hat Stand
Step 4: Secure the beater ball rod into the rocker hub so that the ball
rests about one inch higher than the center of the bass drum head.
Position either the felt or the rounded plastic side towards the head
depending on your preference.
Hi-Hat Stand
Upper Rod
Step 1: Spread the legs on the bottom section of the hi-hat stand*.
Step 2: Screw the upper rod into the center of the stand. DO NOT
PLACE THE ROD IN THE STAND WITHOUT SCREWING IT IN. Turn it
clockwise until it is finger-tight.
Upper Tube
Wing nut
Base Section
3
Final Adjustments
Final Adjustment
Cymbals*: Place your cymbals on the top (tilter section) of the stands.
Be sure to use a felt washer above and below each cymbal. Hand tighten
the wing nut on top of each tilter.
Adjustments: Position the snare, (14") tom Q and hi-hat stands* behind
the bass drum. Sit at your drum kit and adjust the heights and angles of
all your drums and cymbals to a comfortable playing position. Adjust
tuning as necessary. (Please see below for tuning guidelines.)
Step 3: Place the snare drum Q into the open basket. Tighten the knob
under the basket to make the arm snug around the snare drum Q .
Bass Drum Pedal
felt washer. Position the stem of the clutch through the hole in the top
hi-hat cymbal* and replace the nut and felt. Using the top nut, adjust
the space between the cymbal and felts. Place the clutch on the rod and
tighten the wing screw so that the clutch sits 3/4 to 1" above the bottom
cymbal.
Cymbal tilter
Basket
Step 2: Loosen the basket wing screw on the upper section of the snare
stand* and tip the basket up. Pull open the basket arms. To further open
or close the arms, use the knob located at the base of the basket.
Hi-Hat Stand (continued)
Lower felt
Step 3: Loosen the wing screw on the bracket of the 8" tom tom N .
Position it on the tom arm taking care that the arm does not touch the
tom shell. Tighten the wing screw on the tom bracket.
Snare Drum and Snare Stand
Upper felt
Cymbal
Step 2: Attach the fixed side of the single AC991 tom clamp L around
the tube of the cymbal stand*. Position the tom arm so that it is directly
over one of the legs of the cymbal stand* and facing the drummer.
NOTE: The AC991 Tom clamp will have to sustain the pounding of your
drumsticks, double-check that all adjustments are tightened securely.
Cymbal Assembly
Step 3: Remove the clutch from the upper rod. Slide the upper tube of
the hi-hat stand* into the base section and tighten the wing screw.
NOTE: To attach hi-hat cymbals*, place the bottom hi-hat cymbal
through the rod so that it rests upside-down on the felt seat at the top
of the upper tube. Open the clutch by removing the bottom nut and
Have Fun!: Play by yourself, play with records or start a band. Ask your
local authorized PDP dealer about available add-on drums, hardware,
accessories, books, videos and lessons.
Tuning your Pacific Drums
There is a standard “criss-cross” pattern with which you should
ALWAYS tune a drum. Use the recommended tuning sequence positions indicated
on your snare drum head as a guide. Use this criss-cross sequence for each drum
you tune. The following suggestions begin with the drums completely assembled
and tension rods finger tight.
Step 1: Start with the snare drum. Take your drum key A and place it
over the tension rod at position 1. Give the key two clockwise turns.
Step 2: Repeat at position 2, 3, 4, 5, 6, 7, and 8
Tuning The Snare Drum
1
6
A
7
4
3
8
5
2
Step 3: Return to position 1 and turn the key one quarter turn and tap
the drum with your finger about two inches in front of the tension rod.
Using the criss-cross method continue tightening each tension rod
while tapping the drum to make sure it sounds like the previous
position. Continue this process around the drum.
Step 4: When each position is the same pitch, you are ready to start
tuning the bottom (resonant) head.
Step 5: Follow the same procedure and pattern for the bottom
(resonant) head. It is the best to tune the resonant head slighty higher
than the batter head for the snare and bass drums and slightly lower
pitch for your tom toms.
Step 6: Use this same procedure for each drum, including the bass
drum and tom-toms.
4
OPTIONAL RACK SYSTEM
Package Contents
OPTIONAL
HARDWARE
D
C
B
A
A
B
Drum key (1)
Bass Drum Heads (2)
(One Clear Batter & One Black Logo Resonant)
Bass Drum Hoops (2)
18X22" Bass Drum Shell (1)
1. Drum
TS900
Double
Tom Stand
Bass
Pillow
(1)
Claw Hooks (16)
Bass
Tension
Rods (16 + 2 spares)
2. Drum
CB900
Straight/Boom
Cymbal
Metal Washers (48 + 4 spares)
Stand
Lug Receivers (6 spares)
Smaller Tension Rods For Toms (32 +2 spares)
Bass
Mount
Double
Tom Holder (1)
3. Drum
SS900
Snare
Stand
Single AC991 Tom Clamp (1)
Floor Tom Drum Legs (6 - 2 Set Of 3 Legs Each)
4. C900 Straight Cymbal Stand
7X8" Tom Tom (1 - Assembled)
8X10" Tom Tom (1 - Assembled)
5. HH900
Hi-Hat
9X12"
Tom Tom3-Leg
(1 - Assembled)
5X14" Snare Drum (1 - Assembled)
14"
Tom Drum
Clear Heads
(2) Hi-Hat
6.Floor
HH920
Rotating
2-Leg
12X14" Floor Tom Drum (1)
16" Floor Tom Drum Clear Heads (2)
7. DT900Z
Sparkle/Zebra
14X16"
Floor TomWhite
Drum (1)
PDP
Drum Sticks (2)
Throne
900 HARDWARE
HEAVY-DUTY
C
E
2.
F
G
1.
H
M
6.
7.L
O
N
P
Q
V
U
T
S
R
5.K
4.J
I
3.
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
8.
8. DT900S Black Sparkle Throne
Steps to remove contents from
Steps to remove contents from
800 HARDWARE
MEDIUM-DUTY
Box 1 of 2
Box 2 of 2
1. Before
removing
anything from box
1 of 2, Stand
place the box in a
1. CB800
Straight/Boom
Cymbal
location where you will be able remove the contents of the
boxes.
2. CS800 Straight Cymbal Stand
2. Remove the top packet that holds the drum heads for the
B and the two floor tom drums. R & T
bass3.drum
DT820X
Tractor Throne
3. Remove the Bass Drum hoop. C
4. Beneath the hoop, you will find fully assembled (12") P and
4. HH800-01 3-Leg Hi-Hat
(10") O tom drums.
5. Remove all excess packing around the tom drums to ensure
SS800 Snare Stand
easy5.removal.
6. Remove the top tom drum P and then the bottom tom
6. OHH820
2-Leg
drum.
Place drums
on aHi-Hat
smooth and sturdy surface to prevent
damage your drums.
7. DT800-04
Standard
7. Remove
the unassembled
floorThrone
tom U and place the drum on
a smooth and sturdy surface to prevent damage to your drum.
8. Remove the cardboard ring around the bass drum shell D by
grabbing the cut-out handle and lifting upward.
9. Remove the bass drum pillow E ,positioned along the side of
the bass drum shell. D
10. With both hands, grasp each side of the bass drum shell D ;
pull the bass drum shell upward to remove from the packaging.
Place the drum shell on a smooth and sturdy surface to prevent
damage to your drum.
11. Once the bass drum shell D is removed from the box, lift up
the bottom cardboard insert to find the second bass drum
hoop. C
12. Take this time to line up all the drums accordingly by size,
from smallest to largest.
13. Place the two large bass drum heads B (clear/black) on top
of your bass drum shell.
14. Take the two (16") T clear drum heads and place them on
top of the unassembled floor tom drum. U
1.
2.
15. Remove the top rectangular box containing the six legs for
the floor toms. M
16. Place three legs M next to the (16") floor tom U from the
first box.The other three legs will be placed next to the other
floor tom once removed from this box.
17. Next you will find a long rectangular box that includes
drumsticks V , claw hooks F , washers H , and tension rods
G & J that will be used during assembly.
18. Remove the box with the snare drum. Q Place the snare
drum on a smooth and sturdy surface to prevent damage to
your drum.
19. Remove and open the styrofoam box and place the smaller
AC991 tom clamp L aside. Place the larger bass drummounted double tom holder K near the bass drum. D
20. Under the snare drum box, you will find a smaller box with
another tom drum. Remove the drum N from the box
and place the drum on a smooth and sturdy surface to prevent
damage to your drum.
21. Before removing the last drum from this packaging, be
sure to remove the styrofoam blocks to assure easy removal
from the
box.
22. Remove the last floor tom drum S from the box just as you
did earlier for the bass drum.
23.Take
this time3-Leg
to line up
all the drums accordingly by size
1. HH700
Hi-Hat
from smallest to largest as you did earlier.
24. 2.
Take
the three
legs M and placeCymbal
them nextStand
to the floor tom
CB700
Straight/Boom
drum S just removed from the second box.
25. Take the last two remaining (14") clear drum heads R and
3. SS700 Snare Stand
place them on top of the floor tom drum S just removed from
the second box.
3.
4.
5.
6.
7.
700 HARDWARE LIGHTWEIGHT
4.
1.
15
2.
3.
5.
4. CS700 Straight Cymbal Stand
5. DT700 Throne
Main Rack Package (PDSRPK05)
Bass Drum Assembly
Bass Drum Assembly
G
H
F
C
B
D
Bass Drum Assembly
BDM Receiver
Step 1: Set the bass drum shell D on the side with the spurs (legs)
towards the top. Place the black “PDP” logo head B over the shell. Center
the logo underneath the BDM (Bass Drum Mount Receiver) located on
the top of the bass drum.
Step 2: Place one of the bass drum hoops C over the bass drum head
with the flat side of the hoop against the head.
Step 3: Slide 8 metal washers H onto 8 longer tension rods G . Then slide
the tension rod through 8 claw hooks F .
Step 4: Position each claw hook over the bass drum hoop and thread the
tension rods into the lugs around the shell. Tighten by hand only. (You
will fully tighten and tune the drum later.)
Step 5: Set the shell right-side-up.
Combo
Rack
Package
Step 6: Remove
the plastic
backing from (PDSRCOMBO1)
the self-adhesive Velcro tape on
the bass drum pillow E . Attach the pillow inside the bottom of the shell
the adhesive. The pillow should be positioned towards the back of
Rack Accessories with
the shell so that it will lightly touch the batter (clear) head when
A. PDCH1012 Closed Hi-Hat Armassembled.
B.
B. PDDB799 DogBone™ w/ Cymbal
Arm
Step 7:
Turn the drum on its side (black head down) with the pillow
C. PDDB798 DogBone™
D. the shell. Center the
towards the top. Place the clear batter head B over
logo underneath the BDM (Bass
D. PDCB0934 Cymbal Arm (Standard)
A.Drum Mount Receiver) located on
E. the
top of the bass drum.
PDCB0934S Cymbal Arm (Short)
C.
D
E
C B
C
PDCB0978
Cymbal
Boom
ArmStep
(7/8”)
8: Repeat steps 2 through 4 for the batter head.
E. DWSMRKDRKY Hi-Torque Drum key
Step 9: Set the shell right-side-up.
F. DWSMRKFEET Rubber Feet (2-pack)
G.
PDSRC15V
1.5”-V
Clamp
Step
10: By loosening
the wing
nut, angle the spurs so they face
Bass Drum Assembly
H.
DWSMRKC15A
1.5”-V
Angle
Adjustable Clamp
F.
slightly
towards the front
of the bass
drum.
G
F
I. DWSMRKC15T 1.5”-1.5” T-Leg Clamp
D
11: Loosen the spur legs with the drum key Aand lower the legs
J.Step
DWSMRKC15K
1.5”-1.5” Rack Clamp
C
so that the front of the bass drum is lifted about one inch off the
K.ground.
DWSMRKC15SV
1.5”-V Angle Adjustable Stacker
Tighten the spurs.
Clamp
G.
H.
I.
J.
For convenience, you
mayAccessory
now want to tune
your bass
drum
L.NOTE:
DWSMRKC15AC
1.5”
Clamp
w/ Eyebolt
before attaching the tom and pedal. Please refer to page 5 for tuning
M.
DWSMRKML15 1.5” Hinged Memory Lock
guidelines.
DWSMRKML10 1” Hinged Memory Lock
N. DWSMRKTTCA
Tube
Top Toms
Cymbal
K.
L.
M. N.
10"1.5”-3/4”
and 12"
Tom
Adapter
Spurs
B
O.
DWSMRKC15AS
Angle
Step
1: Insert the Double 1.5”-1.5”
tom holder KHinged
into the BDM
receiver on top
of Stacker
the bass drum.
Clamp
P. DWSMRKC15VA 1.5”-V Accessory Clamp
Q.
Step 2: Loosen the wing screw on the bracket of the (10") tom tom O
10"P. and 12" Tom Toms
Q.
DWSMRKC15S
1.5”-1.5”
Adjustable
O.
R.
and
slide it over the right
tom arm onAngle
the left (from
a right-handed
K
P
Stacker
Clamp behind the kit - reverse if you play leftdrummer’s
perspective
O
Take care 10.5
that the
tom Tom
arm does
not w/
touch
the tom shell.
R.handed).
DWSMTA10
mm
Arm
Memory
Lock
the wing screw on the tom bracket.
S.Tighten
DWCPRKB42C
42” Stainless Steel Curved Bar
T.Step
DWCPRKB24C
Stainless
Steel
Curved
Bar
3: Loosen the wing24”
screw
on the bracket
of the
(12") tom
tom P
BDM Receiver
DWCPRKB12S
12”(reverse
Stainless
Steel
StraightTake
Barcare
Position
it on the tom arm
if you play
left-handed).
that
the tom arm does 24”
not touch
the tom shell.
the wing
screw S.
U.
DWCPRKB24S
Stainless
SteelTighten
Straight
Bar
T.
the tom bracket.
V.on DWCPRKB36S
36” Stainless Steel Straight Bar
D
U.
W.
DWCPRKB42S
42”
Steelof Straight
Bar
V.
NOTE:
Don’t worry about
the Stainless
precise placement
the drums at
this
DWCPRKB72S
Steel Straight Bar W.
point.
You will arrange 72”
them Stainless
all later.
DWSMRKCAPS Tube End Caps (2-pack)
PDSRNPLV Pacific Nameplate Bar Level
26
X7 SERIES D
ASSEMBLY AND
1-YEAR LIMITE
Congratulations on your purchase of this
are a step-by-step guide to get you play
The only tool you need is the drum
Additional tips and information can
PACIFIC DRUMS & PERCUSSION
This warranty protects the original retail purchaser, only. If a covere
defect, Pacific will repair or replace the product at no charge. To obt
Drums dealer along with your original proof of purchase. In the case
will then contact Pacific for further instructions and to obtain a Retu
without an RA number. Any and all shipping charges are the respons
Additional tips and information can be found at www.pacificdrums.com
This warranty does not apply to 1) drums purchased from a source o
than the original purchaser, 3) defects caused by neglect, moisture, e
playing conditions, 4) finishes, 5) alterations made after the product
percussion shall not be liable for incidental, consequential or other d
failure of this product. This warranty gives you specific legal rights.
Component
Length of Coverage
Pacific Drums and Percussion. A division of Drum Workshop, Inc. C 2007 Drum Workshop, Inc.
Pacific Drums and Percussion is a registered trademark of Drum Workshop, Inc.
drum shells
l year
d