LS6001A Additional Handset
Quick Start Guide
Package Contents
• LS6001A handset
• Handset charger and power adapter
• NiMH rechargeable battery pack
Connect the Charger
.
Plug the power adapter cable into the charger, plug the other end into the wall jack and switch the power on.
Wall jack
$&9
DC
6V
8VH2QO\
6XSSOLHG
$GDSWHU
&25'/(667(/(3+21(
$&9P$
97HFK&XVWRPHU6HUYLFH
ZZZYWHFKSKRQHVFRP $FFHVVRU\
Power adapter
cable
Charger
NOTES
• Ensure the power cord is fed through the slot on the charger so the unit sits flush with the desk.
• The position in which you place the charger could have an effect on the range and performance of your LS6001A handset.
Install the battery
. Slide open the battery compartment cover. Place the battery pack into the battery compartment, with the battery
connector plugged in, as shown.
. Place the rechargeable battery and the wires inside the battery compartment.
3. Slide the battery compartment cover back until it clicks into place.
4. Place the handset on the base charging cradle to charge for at least 14 hours. A beep indicates that the handset is
properly placed on the base.
1
2
4
3
UP / CE CÔTÉ VERS LE HAUT
THIS SIDE UP / CE CÔTÉTHIS
VERSSIDE
LE HAUT
Battery Pack / Bloc-piles :
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
Made in China / Fabriqué en chine
UP / CE CÔTÉ VERS LE HAUT
THIS SIDE UP / CE CÔTÉTHIS
VERSSIDE
LE HAUT
UP / CE CÔTÉ VERS LE HAUT
THIS SIDE UP / CE CÔTÉTHIS
VERSSIDE
LE HAUT
Battery Pack / Bloc-piles :
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
Made in China / Fabriqué en chine
Battery Pack / Bloc-piles :
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
Made in China / Fabriqué en chine
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
$&9
&25'/(667(/(3+21(
$&9P$
&25'/(667(/(3+21(
$&9P$
$&9
8VH2QO\
6XSSOLHG
$GDSWHU
97HFK&XVWRPHU6HUYLFH
ZZZYWHFKSKRQHVFRP $FFHVVRU\
Place
batterySlide
Slide
battery
Place
battery
thethe
battery
Insert
battery
connec
Insert
battery
connec
• tor
Thistor
handset
requires specific NiMH rechargeable
in HSbatteries for use.
compartment
cover
in HS
compartment
cover
to
to
HSHS
• If you do Insert
not use thebattery
handset for connec
a long time, disconnect
remove the batteries
prevent
possible leakage.
Placeand
battery
Slidetothe
battery
in HS
compartment cover
tor to HS
NOTES
8VH2QO\
6XSSOLHG
$GDSWHU
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
97HFK&XVWRPHU6HUYLFH
ZZZYWHFKSKRQHVFRP $FFHVVRU\
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
Registering an Additional Handset
The LS6001A additional handset must be registered to the LS6191A telephone base before use. When first
purchased, each expansion handset alternately shows To register HS... and ...see manual. The new handset should
be charged without interruption for at least 30 minutes before registering it to the telephone base. To register the
additional handset to your LS6191A, follow the instructions below.
To register a handset:
. At the bottom of the telephone base, press and hold PAGE for about four seconds
until it shows Registering...
. On the cordless handset, press # then it shows Registering... Both the telephone
base and cordless handset show Registered and you hear a beep when the
registration process completes. The registration process takes about 60 seconds
to complete.
If registration fails, the handset displays Failed. Please start again from Step 1 above.
NOTES
• You cannot register a handset if any other system handset is in use.
• If you have not set the date and time for the telephone system, the handset will prompt you to set the
date and time after it is registered to the base. To skip setting, press CANCEL.
If you have any difficulty with the operations of LS6001A handset or LS6191A base station, refer to your
LS6191A User’s manual.
For technical support, please call VTech Technical Inquiry Hotline.
© 2015 VTech Telecommunications Ltd. All Rights Reserved.