Download Report

CORrosionresistand
TENsilestrenght
To form a rusty surface homogeneously and rapidly and to coat them with a slipresistant selection in gloss or for stairs is a challenge that solves this particular
system.
Traditional oxidation processes with aggressive acids and mixtures are fast but
uncontrolled - COR oxide provides this control. The other system components are
specifically designed and tuned for the transparent coating of rusty surfaces
Coating
Klaus-Dieter Braun | Sales-Company
D - 67346 Speyer ( GERMANY )
T +49 6232 919 1411 | F +496232 919 1412
www.kdb-web.de | [email protected]
Stand 02/2013
Before planning + application of the products, see the instructions INDOOR /
OUTDOOR.
You can find these on our website as a PDF file.
>> Pricelist on last page <<
Coating-System - Corten-Steel / Steel
COR säure: Radiation - Descaling (only when necessary)
When weathering steel + standard steel with a thickness of more than 2 mm by hot rolling the steel plant will be always a layer of scale
- some suppliers provide these already descaled steel with / without fat. This roll-skin needs the sand or stain (eg www.nabu-stulln.de)
are removed and the surface should be free of grease. These events open the "pores" and prepare the steel for optimum treatment.
COR-acid cleaner for removing the scale film / roll skin
Before you start the application, it is important rubber gloves (antacid), use of protective goggles and protective clothing or overalls.
Good ventilation is required in confined areas. When using spray [our atomizers not suitable) for application use suitable respirator.
Contact with other materials-metals - coats should be avoided if there is aggression against these. (Note disposal / consider if local
regulations).
In order to achieve a good and faster result, the surface should be free of grease, oil and dirt. We put the acid on the surface and brush
/ distribute several times at intervals of about 5 minutes with a flat paint brush on the surface of the medium to the cleaners with
plenty of oxygen (reactor) into communication. After a break of about 20 minutes, rub the surface with a Scotch-Brite pad. We may
repeat the process throughout the process at intervals of about 20 - 30 minutes to whitish spots result indicating that the process of
rolling detachment begins. To support and as the last process of the surface residual acid / rolling skin remains with old rags or with
water (possibly high pressure when it allows the environment) will be cleaned / rinsed. Now the (dry) surface prepared for either a
natural oxidation or for subsequent processing
COR oxid = activation oxidation
CORoxid is a compound which acts on the steel surface by weather-resistant steel (for example, Corten steel). The area to be treated is
the most uniform and homogeneous image drawing to wet in suitable distance. After this treatment results in a rapid oxidation which
appears to be relatively uniform in color and texture.
In Depending on the temperature and humidity, drying can take about 30 to 45 minutes, at 15 ° C or relative humidity above 95%
significantly increased the drying times. To avoid undesirable effects in the Oxidationstextura during application, including the drying
process should direct sunlight should be avoided. A twofold treatment with COR-oxide is generally id sufficient. The appearance is also
dependent on the factors of the wet thickness, the quality of the steel used and the ambient conditions.
• 2 to 3 applications / treatments at intervals of at least 60 minutes with a brush or roller
COR stop
Is mixed with 50% water and should be better with a roller or with a spray - are wetted and homogeneously applied very evenly / (or
airless sprayer with our manual). CORstop has little impact on the steel color-only subsequent applications make this a little darker.
• (after 24 h CORoxid) = 2 applications at a distance of at least 90 minutes (internal application project )
• 3 applications at a distance of at least 90 minutes (d project outside use)
After 24 - 48 h, the surface is ready for the subsequent finishing treatments, The waiting time of subsequent applications from product
to product is 24 hours!
A cleaning / removing excess oxide powder on the plate is possible until 24 hours after the activation of oxidation and CORstop
application. Since COR-stop adheres relatively strongly recommended water (ideally under pressure) to use. It should be ensured that
no unwanted traces arise. If this is the case, then the on site if necessary to treat new from scratch. Sometimes, especially for exterior
surfaces, to monitor a concentration of micro-oxide grains.
COR natur matt
This varnish is our highlight in relation to an interior look - the sound is similar to the untreated rusted steel, is fast drying with high
elasticity. A relatively smooth surface is the specificity. This paint should not be used on a surface that is wet, or fat is present.
• Interior Projects: 2 applications at intervals of 3 to 4 h
• Outdoor Projects: 1 application per COR + 3 to 4 applications COR natural matt, provided no permanent weathering with rain, sun,
etc..
COR pro - (semibright)
nitro-based steel and corten steel for indoor use. He is on the surface to apply to rain or excessive moisture are exposed to is easy to
apply and dries quickly.
• Interior Projects: 2 applications at intervals of 3 to 4 h
• Outdoor Projects: 1 Application and (serving as a membrane between CORstop and CORglanz!
If the humidity is high and / or there is a chemical environment, this can damage the paint. A maintenance contract with a new paint
layer varies depending on the ambient atmosphere and can be repeated every 5 years.
Subsequent applications - outdoor projects require a base coat-COR 1 application :
COR glanz (gloss)
Polyurethane coating for interior and exterior projects, dries by polymerization reaction = humidity and provides relative protection
and abrasion resistance. It changes the appearance of the untreated steel Corte. Depending on the exposure of the original gloss is
around 8 - 12 months of decline. This lacquer is on COPR per stop or COR applied directly and stop the drying and waiting time.
• 3 applications in the range of 5 to 6 hours
COR sat
lower brightness than COR gloss, but with a high hardness and resistance to moisture absorption, with a smoother and glossy surface.
It is a two-component paint in a ratio of 10:1. This varnish is applied per the film-COR and has an exceptionally good adhesion. It is wise
- especially for large areas - for applying a spray (airless) to use.
• Outdoor use: 2 applications at intervals of 6 to 7 hours
COR poli
This polyurethane coating is a paint with a matte appearance for exterior gloss and protects against COR continuous weathering. It is a
one-component paint with a polymerized dry additive. This lacquer is used to obtain a complete protective layer on the CORglanz. The
characteristic appearance of the Corte steel is little affected. It has a similar shades as CORnatur (inside) but a greater surface hardness.
This compound must be processed after 2 h and may not be used h after mixing of 2 hours.
The product comes with the small bottle additive which can be mixed with one liter of fully. Otherwise, the rule is: 1 can CORpoli =
1000ml + 1 bottle ADDITIVE = 30 ml (eg 200ml + 6ml)
• 2 applications COR gloss every 5 to 6 hours
• After 7 to 8 h 1 application COR policy with about 48 hours of drying time
when high humidity and / or some type of continuous chemical environment exists this can damage the paint. A maintenance contract
with a new paint layer varies depending on the ambient atmosphere and can be repeated every 5 years.
CORmetallic
Water-based with iron particles in imitation that never quite the natural, real Cortenstahl equivalent. Easy to use, to clean and greasefree surfaces such as drywall on. Plaster, gypsum, etc. Can also be used for the repair of Corte surfaces For brush and roller application
with 10% water and spray with 20% water mix well. It is homogeneous when. 2-3 coats but also so much darker in tone and grit If
necessary, use sound, not acid-transparent primer. Temperature for applying 18-25 ° C, dried and at 10 to 20 ° C. Thereafter, the
oxidation is carried out on our actual CORoxid CORstop and on the coated surface with CORmetallic .. as required further coatings are
applicable in this system.
• l is sufficiently dry for 7 - 8 square meters (35 micrometers thick), 24-hour drying time
Price € / 2013 - without tax for company`s - without shipping-costs:
Product
COR-Säure
COR-oxid
COR-stop
COR-pro
COR-natur, matt (Indoor)
COR-glanz, (Outdoor)
COR-sat, incl. Katalysator (Outdoor)
COR-poli, matt incl.Aktivator (Outdoor)
COR-metallic. Imitat
1 l – in
sqm
10-13
20-22
30-35
7-9
7-9
8-9
8-9
20-21
7–8
0,5 l
30,00
35,00
-
Granules for flooring (polished steel - Corten steel) Anti-slip – 1 kg Sprayer with manual pressure pump for CORoxid, Volume: 2 l
Indoorpaket Specialprice only 1 liter:
CORoxid – CORstop – CORpro=halbglanz - (or COR-naturmat) + Sprayer



1l
42,00
64,00
69,00
39,00
44,00
47,00
75,00
79,00
112,00
2l
77,00
116,00
126,00
207,00
47,00
5l
25 l
170,00
233,00
253,00
160,00
159,00
173,00
284,00
273,00
-
710,00
920,00
997,00
-
25,00
160,00
Delivery time in a stock of addiction: 1 - 3 weeks
Minimum order value 80, - €
100 % Payment in advance
NOTES:
The finest and best results in the paint coatings are obtained by using a unique spray device in Airlessprinzip. In paint spraying equipment with air
atomization should dryer or dehumidifier for adequate fixation of coatings provide. Inject no paint on CORstop before this is not completely dry - id
usually 24 hours drying time. A permanently resistant sealing in direktbewitterten outdoors is not guaranteed, if necessary, from time to time to renew /
treatment required. The information given herein is based on descriptions of the actual manufacturer's specifications and are not interpreted as a
binding contract!