Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
REV 15b
Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2015 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to
potential personal injury hazards. Obey all safety messages
that follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
Symbology
Double Insulated
Canadian Standards
Association
Underwriters Laboratories, Inc.
V
~
A
Volts
Alternating Current
Amperes
Important Safety Information
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
Installation Precautions
1. Check federal, state and local
surveillance laws before
installing video and/or audio
surveillance equipment.
2. Install only according to these
instructions. Improper installation
can create hazards.
3. Do not overreach when installing
this product. Keep proper footing
and balance at all times. This enables
better control in unexpected situations.
Page 2
4. Wear ANSI-approved safety goggles
during installation.
5. Keep installation area clean and well lit.
6. Keep children and bystanders out
of the area during installation.
7. Do not install when tired or
when under the influence of
alcohol, drugs or medication.
For technical questions, please call 1-888-866-5797.
Item 62367
Use Precautions
1. This product is not a toy. Do not allow
children to play with or near this item.
2. Use as intended only.
3. Do not modify.
4. Maintain product labels and
nameplates. These carry
important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
Camera Safety Warnings
1. To prevent electric shock, do not
attempt to disassemble Camera. There
are no serviceable parts inside.
2. Use supplied Power Adapter only.
3. The Power Adapter plug must
match the outlet. Never modify
the plug in any way. Unmodified
plugs and matching outlets will
reduce risk of electric shock.
4. Do not expose the Power Adapter
to rain or wet conditions. Water
entering the Power Adapter will
increase the risk of electric shock.
5. Do not abuse the Power Adapter
cord. Never use the cord for
unplugging the plug from the
outlet. Keep cord away from
heat, oil, sharp edges or moving
parts. Damaged or entangled cords
increase the risk of electric shock.
6. Handle Camera with care.
Camera could be damaged by
improper handling or storage.
7. WARNING: The cord of this product
contains lead and/or di (2-ethylhexyl)
phthalate (DEHP), chemicals known
to the State of California to cause
cancer, and birth defects or other
reproductive harm. Wash hands
after handling. (California Health &
Safety Code § 25249.5, et seq.)
8. WARNING: This product contains
or, when used, produces a chemical
known to the State of California to
cause cancer and birth defects or other
reproductive harm. (California Health
& Safety Code § 25249.5, et seq.)
9. People with pacemakers should
consult their physician(s) before
use. Electromagnetic fields in close
proximity to heart pacemaker could
cause pacemaker interference
or pacemaker failure.
10. The warnings, precautions, and
instructions discussed in this instruction
manual cannot cover all possible
conditions and situations that may
occur. It must be understood by the
operator that common sense and
caution are factors which cannot
be built into this product, but must
be supplied by the operator.
Service
Have your Security Camera serviced by a qualified repair
person using only identical replacement parts.
SAVE THESE INSTRUCTIONS.
Item 62367
For technical questions, please call 1-888-866-5797.
Page 3
Grounding
TO PREVENT ELECTRIC SHOCK AND DEATH FROM
INCORRECT GROUNDING WIRE CONNECTION:
Check with a qualified electrician if you are in doubt as to whether the
outlet is properly grounded. Do not modify the Power Adapter plug
provided with the Camera. Do not use the Camera if the power cord or plug is
damaged. If damaged, have it repaired by a service facility before use. If the plug
will not fit the outlet, have a proper outlet installed by a qualified electrician.
1. The included Power Adapter
does not require grounding.
2. The Power Adapter may be
used in either of the 120 volt
outlets shown in the preceding
illustration. (See Figure A.)
Figure A: Outlets for 2-Prong Plug
Extension Cords
Note: Do not use an extension cord with the Power Adapter.
Symbology
Double Insulated
Canadian Standards
Association
VAC
A
Volts Alternating Current
Amperes
Underwriters Laboratories, Inc.
Page 4
For technical questions, please call 1-888-866-5797.
Item 62367
Specifications
Lens
Effective Pixels
Night Vision Type
Image Type
Infrared Wavelength
Wireless Range
Ingress Protection Rating
Night Vision Range
Video Connector
Power Rating
Operating Temperature
Transmission Frequency
1/4" VGA CMOS
640H x 480V
Infrared LEDs with Low Light Sensor
Daylight: Color
Infrared: Black & White
850nm
180 ft (indoors) 650 ft (outdoors)
IP54 - Dustproof, Splashproof
40 ft
RCA
9VDC / 600 mA
14° - 122°F
2.4 GHz
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Item 62367
For technical questions, please call 1-888-866-5797.
Page 5
Installation Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section
at the beginning of this manual including all text under
subheadings therein before set up or use of this product.
TO PREVENT SERIOUS INJURY FROM ELECTRIC SHOCK:
Unplug the Power Adapter from its electrical outlet and verify that installation
surface has no hidden utility lines before drilling or driving screws.
Components
Antenna
Mounting
Hardware
Power Cord
Lens
Microphone
(on bottom)
Speaker
9VDC Power
Adapter
Infrared
Sensor
Mounting
Bracket
Back of Camera
Pair
Button
Antenna
Connector
Power
Cord
Figure B
Page 6
For technical questions, please call 1-888-866-5797.
Item 62367
Assembly
1. Thread the Antenna into the
Antenna Connector on the
back of the Camera.
2. Adjust the Antenna to its vertical
position for best transmission.
Before Mounting
1. When planning mounting
location and angle:
a.Verify that installation surface
has no hidden utility lines before
drilling or driving screws.
b.Take into consideration the
length of the Camera and Power
Adapter’s cords. Route the cords
so as to avoid a tripping hazard.
c.Do not install where there are thick
walls or other obstructions between
the Camera and Receiver.
d.Select a location high enough so that
it is out of reach of children, but still
covers the desired viewing area.
e.Do not install the Camera
facing out of a window.
f. Make sure no strong light will
shine directly into Camera Lens.
g.Make sure location will remain within
the Camera’s Operating Temperature.
2. Test the Camera’s function in its
intended location before mounting:
a.Connect the Power Adapter’s cord
to the Camera’s Power cord.
Figure C
b.Plug the Power Adapter
into a 120VAC outlet.
c.Verify that there is an image
on the Receiver.
3. When the mounting location
has been chosen:
a.Unplug the Power Adapter’s
cord from the Camera.
b.Remove the Camera from
the Mounting Bracket.
c.Using the Base as a template, mark
locations of mounting holes on
mounting surface. (See Figure D.)
Mounting
Holes
Mounting
Bracket
Base
Figure D
Item 62367
For technical questions, please call 1-888-866-5797.
Page 7
Mounting to Solid Surface
1. Using a drill bit slightly smaller
than the Screws, drill pilot holes
into the marked locations.
4. Remove protective film from the Lens.
2. Position Mounting Bracket so that
mounting holes align with pilot holes.
5. Attach Camera to Mounting Bracket,
then loosen Adjustment Knob, adjust
Camera as needed, then tighten
Adjustment Knob. (See Figure E.)
3. Drive Screws through mounting
holes in Base and into pilot holes
until the Mounting Bracket is securely
attached to the mounting surface.
Mounting to Hollow Surface
1. Using a drill bit slightly smaller
than the Anchors, drill holes
in the marked locations.
4. Drive Screws through mounting holes
in Base and into anchor holes until
the Mounting Bracket is securely
attached to the mounting surface.
2. Tap Anchors into the holes until they are
almost flush with mounting surface.
5. Remove protective film from the Lens.
3. Position Mounting Bracket so that
Mounting Holes align with anchor holes.
6. Attach Camera to Mounting Bracket,
then loosen Adjustment Knob, adjust
Camera as needed, then tighten
Adjustment Knob. (See Figure E.)
Adjustment
Knob
Figure E
Page 8
For technical questions, please call 1-888-866-5797.
Item 62367
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section
at the beginning of this manual including all text under
subheadings therein before set up or use of this product.
1. Refer to the receiver’s owner’s
manual for operating the
camera with the receiver.
2. The Camera will operate continuously
while the Power Adapter is plugged in.
3. When not using the Camera, unplug the
Power Adapter from its electrical outlet.
Inspection, Maintenance, and Cleaning
Procedures not specifically explained in this manual must be performed only
by a qualified technician.
TO PREVENT SERIOUS INJURY FROM ELECTRIC SHOCK:
Unplug the Power Adapter from its electrical outlet
before inspection, maintenance, or cleaning.
1. PERIODICALLY, inspect the general
condition of the Camera. Check for:
• loose hardware,
• damaged cord/electrical wiring,
• cracked or broken parts, and
• any other condition that may
affect its safe operation.
Item 62367
2. PERIODICALLY, wipe external
surfaces of Camera with clean cloth.
3. Maintain area surrounding
Camera, making sure obstacles
don’t interfere with visibility,
such as overgrown bushes.
For technical questions, please call 1-888-866-5797.
Page 9
Troubleshooting
Problem
Possible Causes
Probable Solutions
Camera does
not work.
1.No power at outlet.
2.Not paired with
receiver.
1.Check power at outlet.
2.Pair with receiver.
Poor image quality.
Camera lens is dirty.
Clean Camera lens.
View undesirable.
Camera out of
adjustment.
Loosen Adjustment Knob,
adjust Camera as needed, then
tighten Adjustment Knob.
Record Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND
ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE
MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY
OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY
REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY
PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR
HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR
ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Page 10
For technical questions, please call 1-888-866-5797.
Item 62367
Parts List and Diagram
Part
1
2
3
4
Description
Camera
Power Adapter
Screw
Anchor
1
Qty.
1
1
3
3
2
3
4
Item 62367
For technical questions, please call 1-888-866-5797.
Page 11
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this product
is free from defects in materials and workmanship for the period of 90 days from the
date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities,
criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our product.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY
IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us
with transportation charges prepaid. Proof of purchase date and an explanation
of the complaint must accompany the merchandise. If our inspection verifies
the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you
with a replacement. We will return repaired products at our expense, but if we
determine there is no defect, or that the defect resulted from causes not within the
scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797