INSTALLATION GUIDE
Trimble®
PipeDesigner 3D®
Software
Revision A
May 2015
F
Englewood Office
Trimble Navigation Limited
116 Inverness Drive East, Suite 210
Englewood, Colorado 80112
(800) 234-3758
Copyright and Trademarks
©1999 - 2015 Trimble Navigation Limited.
All rights reserved.
Trimble and the Globe & Triangle logo are trademarks
of Trimble Navigation Limited, registered in the United
States and in other countries.
Trimble PipeDesigner 3D and Trimble Quick Link are
registered trademarks of Trimble Navigation Limited.
Other brand and product names are trademarks or
registered trademarks of their respective holders.
Release Notice
This is the Trimble® PipeDesigner 3D® software
INSTALLATION GUIDE. (Revision A).
The topics within this document are:
•
Subject to change without written notice.
•
Companies, names, and data used in any
examples are fictitious.
•
Screenshots included in the help topics may not
be exactly as in the software application.
Part Number PD3D8063.01.1014_Installation
Wednesday, May 13, 2015 11:05 am
IV
INSTALLATION GUIDE
Contents
1
Software Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PipeDesigner 3D Software Information .
Installation Requirements . . . . . . . . . . . .
Autodesk Application(s) . . . . . . . . .
Trimble Quick Link . . . . . . . . . . . .
2
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
8
8
8
8
Trimble® Quick Link Software . . . . . . . . . . . . . . . . . . . . . 11
Quick Link Modules . . . . . . . . .
Recommendations / Requirements .
Insert DVD . . . . . . . . . . .
Install Trimble Quick Link Hub . . .
3
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 12
. 12
. 13
. 14
PipeDesigner 3D® Software . . . . . . . . . . . . . . . . . . . . . . . 19
Insert DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Additional Software/Information . . . . . . . . . . . . . . . . . . . . . 24
4
Adobe® Reader® Software . . . . . . . . . . . . . . . . . . . . . . . 25
Verify Reader Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Install Adobe Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5
Getting Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Software Modules . . . . . . . . . .
PipeDesigner 3D CAD . . . . .
PipeDesigner 3D Data Editor .
QuickMerge . . . . . . . . . .
Licensing . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
INSTALLATION GUIDE
. 28
. 28
. 28
. 29
. 29
v
Content
Trimble Quick Link Configuration
Configure and Obtain Licensing .
Open PipeDesigner 3D . . . . . . . . . .
License Manager . . . . . . . . .
Recommended Settings . . . . .
Install Metric Database . . . . . .
6
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 29
. 30
. 31
. 34
. 34
. 35
Online Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Product Assistance . . . . . . . . .
Online Help System . . . . .
Online Manuals . . . . . . .
Trimble MEP Client Services
vi
.
.
.
.
.
.
INSTALLATION GUIDE
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 38
. 38
. 38
. 41
CHAPTER
1
Software Overview
1
In this chapter:

Installation Requirements

Autodesk Application(s)

Trimble Quick Link
PipeDesigner 3D provides a CAD solution
to designers of piping systems. Created
by industry specialists, it integrates with
various Autodesk applications to enable
you to design piping systems more easily
and more quickly. The benefits of
PipeDesigner 3D include:
• Choosing parts from a database of
PipeDesigner 3D entities
• Configuring the system and assigning
parts list and an insulation schedule
• Using intelligent PipeDesigner 3D
entities
• Less UCS manipulation
• Close integration with Autodesk
applications for minimal learning
curve
INSTALLATION GUIDE
7
1
Software Overview
PipeDesigner 3D Software Information
Each PipeDesigner 3D entity contains some intelligence; for example, when you create
a run of piping, PipeDesigner 3D recognizes the minimum and maximum length for the
pipe, and cuts it accordingly. PipeDesigner 3D provides a number of ways to take
advantage of this intelligence, including the ability to derive a Bill of Materials list from
your drawing.
PipeDesigner 3D is closely integrated with several Autodesk applications. You will
quickly become proficient in using the software application!
Installation Requirements
Autodesk Application(s)
Prior to proceeding with the PipeDesigner 3D program, you must have the compatible
Autodesk® application installed and authorized on your computer. Refer to the
installation information included with your Autodesk application for procedures.
Trimble Quick Link
B
Tip – You must install the Trimble Quick Link software before installing
PipeDesigner 3D software. If you have other Trimble applications using the
licensing utility, you do not need to install another Hub; however, you must
install the release of Trimble Quick Link included with PipeDesigner 3D (as an
update) to ensure proper access to licensing functionality.
The Trimble® Quick Link software utility allows you to easily manage licenses for your
Trimble products. PipeDesigner 3D requires Trimble Quick Link for licensing and
communication purposes. The software will not run without the Quick Link product.
8
INSTALLATION GUIDE
Software Overview
1
The Trimble® Quick Link application has two modules available.
• Trimble Quick Link Hub
You must install the Trimble Quick Link Hub before you install the PipeDesigner 3D
application. The Hub serves as the central communication link between the
PipeDesigner 3D software and Quick Link Central (licensing server) located in our
corporate offices.
B
•
Tip – Trimble recommends that the Trimble Quick Link Hub be installed in a
location easily accessible by all who need to use PipeDesigner 3D.
Trimble® Quick Link Management Studio
– The Quick Link Management Studio allows you to manage your licenses from
one convenient location.
– You should limit the number of Management Studio installations within your
organization. This ensures licensing is managed in the most efficient manner.
B
Tip – Trimble recommends that you install at least one copy of the Management
Studio at each of your company's physical locations.
Additional Installation Information
In order to perform the installation, you must have local administrative rights for the
computer on which the application is being installed. If you have any questions, please
discuss with your System Administration personnel.
Before you install the software, take the following action.
Close down all Microsoft Windows® based applications on the server, including
e-mail software.
Note – You must also close the Hub and Management Studio before proceeding. If you
are using the Trimble Quick Link software with any other application, they will not
have access to licensing during the installation process. Trimble recommends you
install this software during a non-busy time to limit disruption of your company’s
workflow.
INSTALLATION GUIDE
9
1
Software Overview
Common Installation Commands
During the installation process, you will see the following in many of the windows.
• To proceed with the installation and advance to the next window, click Next.
• If you want to return to the previous page, click Back.
• If you want to stop the installation, click Cancel. You will be asked to confirm the
cancellation.
• Finish completes the installation.
B
Tip – Before beginning the installation of the Trimble Quick Link and
PipeDesigner 3D software applications, you must ensure that the compatible
Autodesk application and version(s) supported by this release of the
PipeDesigner 3D software is installed on your system.
10
INSTALLATION GUIDE
CHAPTER
2
Trimble® Quick Link
Software
2
In this chapter:

Quick Link Modules

Recommendations / Requirements

Install Trimble Quick Link Hub
The Trimble® Quick Link software utility
allows you to easily manage licenses for
your Trimble products. PipeDesigner 3D
requires Trimble Quick Link for licensing
and communication purposes. The
software will not run without the Quick
Link product.
INSTALLATION GUIDE
11
2
Trimble® Quick Link Software
Quick Link Modules
B
Tip – Before to installing Trimble Quick Link, you should verify whether the
Quick Link Hub is already installed somewhere on your network for use with
other Trimble applications. If you are not certain whether the Quick Link Hub is
installed, you may need to ask your IT Professional for assistance in locating it. If
the Trimble Quick Link software is installed, you must install the release of
Trimble Quick Link included with PipeDesigner 3D software (as an update) in the
same location to ensure proper access to licensing functionality.
Trimble® Quick Link has two modules available.
• Quick Link Hub
This module is required for communicating with Quick Link Central (licensing
server). See Install Trimble Quick Link Hub, page 14 for more details on the hub.
You must install at least one hub at your physical location.
• Quick Link Management Studio
The Quick Link Management Studio allows you to manage your licenses. You can
install it on one or multiple workstations. Trimble recommends that you limit the
number of management studios installed at your location. See Install Trimble Quick
Link Management Studio, page 15 for more information on this module.
Recommendations / Requirements
To ensure proper operation of Trimble Quick Link after installation, follow the steps
below.
• Close down all Microsoft Windows® based applications on the server, including
e-mail software.
• It is recommended that the Trimble Quick Link Hub be installed in a central location
where all PipeDesigner 3D stand-alone and workstation software installations can
easily connect.
• Additionally, you may need to enable the following for the Quick Link application to
work properly:
– Server 2008 and Server 2008 R2: You may need to enable the .NET Framework
3.0 Features in the Server Manager.
12
INSTALLATION GUIDE
Trimble® Quick Link Software
2
– Server 2012: You may need to enable the .NET Framework 3.5 Features in the
Server Manager
B
Tip – Contact your IT Professional if you need assistance with the processes
above.
Insert DVD
Insert the PipeDesigner 3D Installation DVD into the appropriate drive of the computer
designated as the stand-alone or server computer. Wait a moment.
If the installation does not start a few seconds after you insert the installation DVD,
proceed as follows:
• Double-click on the Computer icon on your Desktop.
• Locate the drive containing the PipeDesigner 3D Installation DVD. Click on it to
display the contents of the DVD.
• Double-click AutoRun.exe to open the PipeDesigner 3D main installation screen.
Note – Depending on your computer settings, the .exe file extension may not display.
Trimble Quick Link Video
The installation DVD includes a video introducing Trimble® Quick Link features that
improve licensing and communication for your Trimble product. We strongly
recommend that you view this video before installing any software.
• In the main PipeDesigner 3D installation screen, click Trimble® Quick Link and then
click Quick Link Video Intro. This video provides you with information about the
Trimble Quick Link software application. Trimble recommends that you view this
video prior to beginning the installation process.
• When viewing is complete, you must maximize the main installation screen by
clicking
on your Taskbar.
INSTALLATION GUIDE
13
2
Trimble® Quick Link Software
Install Trimble Quick Link Hub
The Trimble Quick Link Hub provides communication with the Trimble licensing server.
• Using the Quick Link Hub typically requires internet access to allow proper
communication with the license server. If you do not have access to the internet,
you must install the Quick Link Hub and then contact Trimble MEP Client Services
for further instructions.
Note – You must have access to e-mail.
• Trimble recommends that you install the Hub on a computer that can be accessed
by all Trimble software applications.
• If your company has multiple locations using Trimble software applications, you
must install the Hub at each physical location.
• Only one installation of the Hub is required for all Trimble applications (per
location).
• If you are using the Trimble software as a Stand-Alone with no access to a network,
you must install the Hub on that computer.
Hub Installation
B
Tip – Before to installing Trimble Quick Link, you should verify whether the
Quick Link Hub is already installed somewhere on your network for use with
other Trimble applications. If you are not certain whether the Quick Link Hub is
installed, you may need to ask your IT Professional for assistance in locating it. If
the Trimble Quick Link software is installed, you must install the release of
Trimble Quick Link included with PipeDesigner 3D software (as an update) in the
same location to ensure proper access to licensing functionality.
1. On the main PipeDesigner 3D installation screen, click Trimble® Quick Link (under
Software Installation Links).
2. Click Quick Link Hub.
3. The welcome screen displays. Click Next.
4. The License Agreement displays on the screen. Read the agreement. Choose I
accept the terms of the license agreement. Click Next.
14
INSTALLATION GUIDE
Trimble® Quick Link Software
B
2
Tip – You must accept the terms of the agreement to proceed with the
installation. If you want a hard copy of the agreements, click Print.
5. In the Choose Destination Location screen, click Next.
Note – Trimble recommends that you accept the default location.
6. In the Ready to Install the Program screen, read the information provided. When
you are ready to begin the procedure, click Install. The procedure installs the
required files and configures the service. Please be patient as this process may
take a few minutes.
7. Click Finish.
8. Open the Trimble Quick Link Hub to obtain the TCP/IP Address and TCP/IP Port for
the computer where the software is installed. You need this information when
installing PipeDesigner 3D. Also, you need this information when you install the
Management Studio.
Install Trimble Quick Link Management Studio
B
Tip – Trimble recommends that you limit the number of Management Studio
installations within your organization. Limiting the number of Management
Studio installations within your organization provides better license
management and security.
INSTALLATION GUIDE
15
2
Trimble® Quick Link Software
1. If you are installing the Management Studio on a different computer, insert the
DVD into the appropriate drive of that computer (refer to page 13 for instructions).
Click Trimble Quick Link (under Software Installation Links).
OR
If you are installing it on the same computer, click Quick Link Management Studio.
The routine prepares the files for installation.
The Welcome screen displays. Click Next.
2. The License Agreement displays on the screen. Read the agreement. Choose I
accept the terms of the license agreement. Click Next.
Tip – You must accept the terms of the agreement to proceed with the
B
installation. If you want a hard copy of the agreements, click Print.
3. In the Choose Destination Location screen, click Next.
Note – Trimble recommends that you accept the default location.
4. In the Ready to Install the Program screen, read the information provided. When
you are ready to begin the procedure, click Install.
5. Click Finish. Refer to the Getting Started section in this manual for information on
configuring the Management Studio. No action is required at this time.
6. In order to install the PipeDesigner software, click Back to Main screen. Do not
open the Management Studio at this time.
16
INSTALLATION GUIDE
Trimble® Quick Link Software
2
Install the PipeDesigner 3D Software
After you have completed the Trimble Quick Link software installation, you are now
ready to install the PipeDesigner 3D software. Refer to the next chapter for complete
instructions.
INSTALLATION GUIDE
17
2
Trimble® Quick Link Software
18
INSTALLATION GUIDE
CHAPTER
3
PipeDesigner 3D®
Software
3
In this chapter:

Insert DVD

Installation Procedures

Additional Software/Information
PipeDesigner 3D can be installed on a
network or on a stand-alone, single-user
computer.
• The program uses a Microsoft® SQL
Server to hold and manage database
files.
• The Trimble® Quick Link
communication and licensing
software is required.
To ensure proper behavior of the
application, please follow all of the
procedures as outlined in this chapter.
INSTALLATION GUIDE
19
3
PipeDesigner 3D® Software
Insert DVD
Insert the PipeDesigner 3D Installation DVD into the appropriate drive of the computer
designated as the stand-alone or server computer. Wait a moment.
If the installation does not start a few seconds after you insert the installation DVD,
proceed as follows:
• Double-click on the Computer icon on your Desktop.
• Locate the drive containing the PipeDesigner 3D Installation DVD. Click on it to
display the contents of the DVD.
• Double-click AutoRun.exe to open the PipeDesigner 3D main installation screen.
Note – Depending on your computer settings, the .exe file extension may not display.
Installation Procedures
B
Tip – You must have the TCP/IP Address and TCP/IP Port for the Quick Link Hub.
If you have not yet installed the Trimble® Quick Link software, you must do so
before you can install PipeDesigner 3D.
To install PipeDesigner 3D, proceed with the following instructions.
1. In the Software Installation Links area, click PipeDesigner 3D.
Trimble has built-in several validations to ensure Trimble® Quick Link and
PipeDesigner 3D can communicate properly after installation. Your Quick Link Hub
must be validated before you can continue the installation.
2. In the Check Quick Link Installation dialog, enter the following information:
Hub Address
This is the TCP/IP Address assigned to the Quick Link Hub.
Port
This is the TCP/IP Port assigned to the Quick Link Hub. The default Port should
always be 31958.
Click Continue.
20
INSTALLATION GUIDE
PipeDesigner 3D® Software
3
Validation Procedure
When you click Continue, the application validates the installation and
communication with the Quick Link Hub.
– If the installation/communication is validated, a Connection Valid message may
display. Click OK. Go to Step 1 under Continue Installation.
– If installation/communication cannot be validated, you will receive a message.
Click Go Back and make sure you have entered the correct information. Make
any necessary corrections and then click Continue again. Go to Step 1 under
Continue Installation.
B
Tip – If you have entered the correct information and the data cannot be
validated, you will need assistance from your IT professional. Trimble has
provided an Installation Checklist document to step through some
troubleshooting procedures in order to make sure your environment allows the
proper required communication.
INSTALLATION GUIDE
21
3
PipeDesigner 3D® Software
Continue Installation
1. The Welcome to the Installation Wizard for PipeDesigner 3D screen displays. Click
Next.
2. The License Agreement displays on the screen. Read the agreement. Click I accept
the terms of the license agreement and then click Next.
3. The Support Agreement displays on the screen. Read the agreement. Click I accept
the terms of the support agreement and then click Next.
Tip – You must accept the terms of each agreement to proceed with the
B
installation. If you want to print the agreements before proceeding, click the
Print button.
4. In the Select Install Type screen, choose the appropriate option button based on
the type of installation you want to perform. Refer to the information in the tables
below for an explanation and instructions for each installation type.
Workstation: Both CAD and Data Editor Applications
B
Tip – If you are installing as a workstation, you must install the software
on the server as well. See DataServer: Database and Tools section below.
Selecting this option provides access on the installation computer to both the
CAD and Data Editor modules in PipeDesigner 3D.
• If this is the type of install you wish to perform, select the radio button and
then click Next.
• In the Choose Destination Location screen, click Next. Trimble recommends
that you accept the default location.
22
INSTALLATION GUIDE
PipeDesigner 3D® Software
3
DataServer: Database and Tools
This option is for network installations where multiple users will be accessing
the application. With this option, you cannot use the application at the server.
• If this is the type of install you wish to perform, select the radio button and
then click Next.
• In the Choose Destination Location screen, click Next. Trimble recommends
that you accept the default location.
Stand-Alone: Installation of all Features
This option installs all features on the computer.
• If this is the type of install you wish to perform, select the radio button and
then click Next.
• In the Choose Destination Location screen, click Next. Trimble recommends
that you accept the default location.
Custom (WARNING: For expert use only)
This option allows selection of the features you want to install.
C
CAUTION – Trimble strongly recommends that you contact MEP Client
Services before selecting this option. Additional steps may be required to
ensure proper operation of the PipeDesigner 3D program after installation.
5. The Ready to Install the Program screen, click Install.
MIcrosoft SQL Server
PipeDesigner 3D may require additional software to manage database files. The
installation routine will attempt to locate Microsoft SQL Server files. If the necessary
files are not found, the routine automatically launches installation immediately. Please
be patient as this process will take some time to complete. Do not click Cancel during
this process.
INSTALLATION GUIDE
23
3
PipeDesigner 3D® Software
Complete Installation
When installation is complete, click Finish.
Additional Software/Information
Adobe® Reader®
The PipeDesigner 3D software includes various manuals available in a Portable
Document Format (PDF). In order to view these documents, Adobe Reader is required.
If not installed on your computer, you can install it from your PipeDesigner 3D
Installation DVD. See page 25 for instructions.
B
Tip – If you are using a Windows 8 Operating System, a PDF Viewer is
automatically included. Installing A PDF Reader is not required.
Tekla® BIMsight
The Tekla® BIMsight is a professional tool used for construction collaboration. It
combines many facets of the construction process. It allows you to check for clashes
and to share information. The software helps you identify issues and take necessary
corrective steps before construction commences. A link to download a free copy of
this software is included on the installation DVD.
Licensing and Database Access.
To license your PipeDesigner 3D software and learn how to start using the application,
refer to the Getting Started chapter beginning on page 27 for detailed information.
24
INSTALLATION GUIDE
CHAPTER
4
Adobe® Reader®
Software
4
In this chapter:

Verify Reader Version

Install Adobe Reader
B
Tip – If you are using a Windows 8
Operating System, a PDF Viewer is
automatically included. Installing
Adobe Reader is not required.
The PipeDesigner 3D software
application includes online
documentation in a Portable Document
Format (PDF), which requires a PDF
Reader.
B
Tip – If you are currently using
Adobe Reader, it must be at least
version 7.0 to open and view the
available PipeDesigner 3D
software documentation onscreen.
INSTALLATION GUIDE
25
4
Adobe® Reader® Software
Verify Reader Version
To verify that you have Adobe Reader Version 7.0 or greater installed on your
computer, do the following.
1. Open the Adobe Reader program. Choose Help > About Adobe Reader.
2. In the product information window verify that the version is 7.0 or greater.
– If it is, no further action is necessary.
– If not, you must download and install the Adobe Reader application.
Other Considerations
• If you have installed the PipeDesigner 3D software on a network with workstations,
you must install the Adobe Reader program on each workstation.
• If you have installed the PipeDesigner 3D software on a stand-alone computer, you
must also install the Adobe Reader program on the stand-alone computer.
Install Adobe Reader
To install a free copy of the most current Adobe Reader program, follow the
instructions below.
1. Insert the PipeDesigner 3D installation DVD into the appropriate drive of the
workstation computer. Wait a moment. The PipeDesigner 3D installation screen
displays.
2. Under Product Documentation, click Adobe Reader Download. This takes you
directly to the Adobe website.
3. On the Adobe website, navigate to the Adobe Reader download location. Follow
the instructions provided on the download page.
26
INSTALLATION GUIDE
CHAPTER
5
Getting Started
5
In this chapter:

Software Modules

Trimble Quick Link Configuration

Licensing

Open PipeDesigner 3D

Install Metric Database
When you complete the installation
procedures, you are ready to start
working in PipeDesigner 3D. This chapter
provides you with the steps required
after the installation is complete.
• Obtaining license seats through the
Trimble® Quick Link software.
• Restoring the Metric database (if you
need to use it)
• Opening the PipeDesigner 3D
application
Before you proceed with the directions
contained in this chapter, make sure you
have completed all installation steps
required as outlined in the previous
chapters.
INSTALLATION GUIDE
27
5
Getting Started
Software Modules
B
Tip – This section provides an overview of the modules available in the
PipeDesigner 3D software. Before you can access any of the modules, you must
first license your software through the Trimble Quick Link. Refer to Licensing,
page 29 for details.
The PipeDesigner 3D software includes several modules to allow for better
organization while working in the software.
PipeDesigner 3D CAD
The PipeDesigner 3D CAD software is an excellent solution for designers of piping
systems. PipeDesigner 3D includes the following features:
• Choosing parts from a database of PipeDesigner 3D entities
• Configuring the system and assigning parts list and an insulation schedule
• Using intelligent PipeDesigner 3D entities
• Less UCS (User Coordinate System) manipulation
PipeDesigner 3D Data Editor
The Pipe Designer 3D Data Editor is designed for editing specifications and
components that are used when creating your drawing. It provides an intuitive
interface to create, modify, and manage data that is critical to using PipeDesigner 3D.
The Data Editor is organized to provide you with easy access to data used in
PipeDesigner 3D. Each is located under tabs and ribbons so you can add, edit,
duplicate items with a click of the mouse, allowing for quick data entry.
28
INSTALLATION GUIDE
Getting Started
5
QuickMerge
The QuickMerge utility allows you to merge additional database information into the
master. You can also use QuickMerge utility to export data you select out to a file,
which can then be merged into another PipeDesigner 3D database. This allows you to
share data easily. See the online help system for details instructions. Refer to the
online help system for detailed instructions on using this utility.
Licensing
You must obtain licensing through the Trimble Quick Link Management Studio
application before you can use the PipeDesigner 3D software.
Trimble Quick Link Configuration
Before you can use the Trimble Quick Link Management Studio, it must be configured
to communicate with the Hub. The Management Studio provides the tools to obtain
licensing for the PipeDesigner 3D software through the Quick Link Server.
Trimble provides an activation code to you by e-mail shortly after your order is
processed. This activation code is required to obtain your PipeDesigner 3D license
seats. If you cannot locate this e-mail or code, please contact MEP Client Services at
(800)234-3758.
1. Open the Trimble Quick Link Management Studio using one of the following
methods:
Click
on your Desktop.
OR
Go to the Windows Start menu and navigate to Trimble® Quick Link. Click on it and
then click Management Studio.
The Trimble® Quick Link Hub must running before you can open the Trimble®
Quick Link Management Studio.
INSTALLATION GUIDE
29
5
Getting Started
2. In the Connect to the Trimble® Quick Link Hub screen, enter the following:
Login Name: admin
Password: admin
B
Tip – Trimble recommends that you change the password for the default login
as soon as possible in order to protect your data. Make note of the new
password.
If you want to save the password for future use, click the Remember Password
checkbox.
3. The login screen may include defaults for the TCP/IP Address for the Hub and Port
Do not change these. If you want to review the default information or update the
data, click
to view the information. You should have the TCP/IP address for
the Hub available for verification purposes.
C
CAUTION – Changing the Port number will cause connectivity conflicts to the Hub
(based on firewall settings). It is highly recommended that the default Port
number is used. Contact your system administrator for more information.
4. Click OK. The Quick Start Wizard opens. This wizard guides you through setting up
the Management Studio for proper licensing and communication. Refer to the
Trimble Quick Link online help system for instructions on completing the wizard.
Configure and Obtain Licensing
B
Tip – At any time during this process, you can click
previous screens.
to return to the
1. In the Quick Start Wizard welcome screen, read the information presented and
then click Next. The hub name screen displays.
2. You must enter a value in the Enter Hub Name field. Click Next.
3. In the Enter your activation code field, you must input the code provided to you
previously by e-mail. Click Next. If you cannot locate this e-mail or code, please
contact MEP Client Services at (800)234-3758.
4. In the Select Product pane, click PipeDesigner 3D® and then click Next. The
licensing operation screen displays.
30
INSTALLATION GUIDE
Getting Started
5
5. In the license seat counts screen, enter the number of seats you want to retrieve
and use. If you are using the PipeDesigner 3D software in a network environment,
you can retrieve licenses to cover all workstations at this time. You cannot obtain
more seats than you have available. Click Next.
6. Review your PipeDesigner 3D software license seat information.
7. If you are satisfied with the results, click Finish. After this process is complete, you
can open the PipeDesigner 3D software application.
Open PipeDesigner 3D
1. Double-click on the PipeDesigner 3D [AutoCAD compatible application] desktop
icon.
OR
Double-click on the PipeDesigner 3D Data Editor desktop icon.
Note – You can also open either module from the Windows® Start menu.
The compatible Autodesk application opens first. Once it is open, the PipeDesigner
3D software opens. Depending on the speed of your computer, this process may
take a few minutes.
Tip – The PipeDesigner 3D software application includes enhanced security to
B
protect your important data. Because of the security feature, steps are required
to setup your database. These steps can be accomplished when opening
PipeDesigner 3D CAD or the PipeDesigner 3D Data Editor.
2. In the Trimble PipeDesigner 3D® Login window, enter the defaults:
Login Name: admin
Password: admin
BTip – These fields are case sensitive. You must enter exactly as above.
INSTALLATION GUIDE
31
5
Getting Started
3. If the window opens with Default Connection in the Database field, click OK.
OR
If Default Connection does not display, click
next to the Database field.
The Define Database Connection dialog opens.
4. In the Define Database Connection window, proceed as follows:
a. Enter an Alias Name. This is a user-defined field. Trimble recommends that
you use a name that will be easily remembered, for instance, My PipeDesigner
3D or your name followed by PipeDesigner 3D Database.
b. The Database Type defaults to Microsoft SQL Server. Trimble recommends
that you leave this as the default. If you want to use another database type,
contact MEP Client Services for more information.
c.
Click
next to the Server Name field. This automatically selects the
Microsoft SQL Server installed locally with PipeDesigner 3D.
If you are using a Microsoft SQL Server on the network, click
to select
the appropriate server from the list or if you know the name of the network
files, you can enter this information manually. It must be entered accurately or
the server will not be recognized.
32
INSTALLATION GUIDE
Getting Started
5
d. Click the Use SQL Server Authentication option button. This provides
enhanced security for your database.
e. Enter the Login information.
The login information below pertains to the Trimble installed instance of the
Microsoft SQL Server. If you are using another installed server, your login will
be different. Contact your IT Professional if you have any questions.
Login: sa
Password: Trimble1
BTip – These fields are case sensitive. You must enter exactly as above.
Trimble recommends that you click Remember Password. This option saves
only the SQL password so you do not have to re-enter it each time you open
the database. The user password (entered in step 2) is still required.
f.
In the Database field, select QPPD3D from the list if you are using the default
non-Metric database. If you are using the Metric database, refer to Install
Metric Database, page 35,
g. Click OK.
5. The Trimble PipeDesigner 3D® Login window displays again. Click OK.
6. If you are opening the CAD side, in the Project Selection dialog, click Default
Project and then click Select & Close.
Tip – You can customize this project in the PipeDesigner 3D Data Editor to
B
conform to your company requirements. You can also create additional projects.
See the online help system for more information.
You are now ready to use the PipeDesigner 3D software.
INSTALLATION GUIDE
33
5
Getting Started
License Manager
The PipeDesigner 3D software application license manager defaults to your entries
from the validation process in the installation routine. If necessary, you can change
these settings under PD3D™ Tools / Miscellaneous / License Manager.
Refer to the PipeDesigner 3D online help for detailed instructions.
C
CAUTION – Use extreme care when changing these settings. Incorrect settings
will disable communication with the Quick Link Hub. In this case, The
PipeDesigner 3D software will not be able to obtain proper licensing to function.
Recommended Settings
Trimble recommends that you set up the following in the PipeDesigner 3D Data Editor
before you create drawings:
• General Settings
• Employees
• Customers
Refer to the online help system for details on these settings.
34
INSTALLATION GUIDE
Getting Started
5
Install Metric Database
If you need the Metric database, complete the procedures below to add it to your
PipeDesigner 3D system.
1. Insert the PipeDesigner 3D installation DVD.
2. Go to Explore / Installation Disk and then click on the Databases folder. Locate
QPPD3D_MET.qps and copy this file to your Desktop.
Note – Depending on your computer settings, file extension may not display.
3. Go to the Windows Start menu and navigate to Trimble PipeDesigner 3D /
Database Restore Utility.
4. Complete/select the required fields in the MS SQL Restore Wizard window.
– Server
– Server type: SQL Server
– User Name: sa
– Password: Trimble1
– If not already selected, click the Save Password checkbox.
5. In the Database field, enter a unique name for the Metric database, for example,
‘QPDD3D_MET.” Click Connect.
6. In the second restore wizard screen, navigate to the QPPD3D_MET.qps file copied
to your Desktop (in step 2 above). Click on the file. Click Next.
Tip – At any time during this process, you can click Back to return to the
B
previous screens
7. Review the information in the third restore wizard screen. If satisfied, click
Restore.
8. When the restore procedure is finished, the screen contains a message that the
procedure is complete. Click Close.
INSTALLATION GUIDE
35
5
36
Getting Started
INSTALLATION GUIDE
CHAPTER
6
Online Help
6
In this chapter:

Online Help System

Manuals from the Start Menu

Find Information in the Manuals
Obtaining information is important when
you are working in any software
package. PipeDesigner 3D provides
online documentation that can be easily
accessed.
This chapter explains the organization
and content of the documentation.
INSTALLATION GUIDE
37
6
Online Help
Product Assistance
Trimble offers several avenues to obtain help using the PipeDesigner 3D software
program.
Online Help System
Accessing online help can be done from the CAD side and Data Editor in PipeDesigner
3D.
• In the PipeDesigner 3D Data Editor, you can press [F1] in most windows to obtain
step-by-step instructions on the window/dialog.
• Help is also available from the Help panel. Click Help Contents and then use the
Table of Contents, Index, Search to locate the information you need.
• On the CAD side of PipeDesigner 3D, you can go to the PD3D™ Tools tab and then
click Help. Use the Table of Contents, Index, Search to locate the information you
need.
– The Table of Contents is organized into categories for easy navigation.
– The Index allows you to locate key words throughout the help system.
– The Search feature provided the functionality to find specific words used in the
help system; for example, you might search for the word delete for instructions
on deleting certain data from your system.
Online Manuals
The PipeDesigner 3D documentation includes the following:
• Installation Guide
Contains information on installing PipeDesigner 3D and initial access to the
database. A hardcopy of this manual is provided.
• Getting Started Guide
Includes exercises that familiarize you with the PipeDesigner 3D system; depending
on the terms of your sale, a hard copy of this manual may be provided with your
software. (It is also available from the Windows Start menu.)
38
INSTALLATION GUIDE
Online Help
6
• PipeDesigner 3D CAD Help Guide
PipeDesigner 3D Data Editor Help Guide
These manuals mirror the online help system in a PDF format.
If you want professionally bound hard copies, see the Printable Manual topic in the
online help file.
Click reprint authorization
This document contains all the information a printer needs to professionally produce
printed and bound manuals. Keep in mind that the help and manuals are updated
regularly. If you print and bind the entire manual, your copy will be obsolete the next
time you receive a software update.
Trimble suggests that you follow the instructions included on the following pages to
open the online manuals. This will allow you to see how easy it is to use manuals
online.
INSTALLATION GUIDE
39
6
Online Help
Manuals from the Start Menu
To open the online manuals from the Start menu, do the following.
1. Choose the Start menu and then go to Trimble PipeDesigner 3D /
Documentation.
2. Click on the appropriate manual.
Find Information in the Manuals
There are several methods to find information when using online manuals.
• Check the index for each manual. The topic you want is probably there. If you are
unable to locate the topic, try thinking of the topic a little differently; for instance,
you might try looking for the word “deleting” instead of the word “removing.”
• Scan the Table of Contents for each manual. Look for the topic you need. The
contents are logically arranged for proper use of PipeDesigner 3D.
B
Tip – Tables of Contents and Indexes are linked to each chapter or topic. Click on
the item in the Table of Contents or Index and the online manual automatically
moves to the page for that topic.
When you open the manual, the Adobe Reader window displays.
• The Navigation Pane is located on the left side of the window. The Navigation Pane
displays section, chapter and topic information.
• Use the Find tool to search for keywords in the online manuals.
• The online manual contains blue references (hyperlinks). Clicking on a hyperlink
will immediately take you to the page or topic referenced. Using hyperlinks allows
you to navigate quickly through the manuals to find specific information.
40
INSTALLATION GUIDE
Online Help
6
Trimble MEP Client Services
Before calling Client Services, we suggest you consult the online help. Many of the
common procedures and questions are covered in this system.
Trimble MEP Client Services is available during regular business hours, Monday
through Friday.
Note – We are not available on major holidays.
Telephone
Toll-free
1-800-234-3758
Internet e-mail
[email protected]
Website
mep.trimble.com
INSTALLATION GUIDE
41
6
42
Online Help
INSTALLATION GUIDE