User Manual / Warranty

GYRO VISION
User manual
MOTO GYRO VISION
at
MOTOGYROVISION.com
(909)565-2086
7606 Freestone Ct.
Rancho Cucamonga, CA
91739
4/20/2015
1
TABLE OF CONTENTS:
GYRO VISION FEATURES……………………………………………………………….3-4
USING GYRO VISION ……………………………………………………………………5-7
GYRO VISION WARRANTY……………………………………………………………….7
WARRANTY REPAIR & REPLACEMENT INSTRUCTION………………………8
2
GYRO VSION FEATURES:
GYRO VISION SCHEMATIC
3
GYRO VSION FEATURES:
1. Brushless Electric Motor
2. Electronics (Do Not Open)
3. Status Indicator Light
4. Initialization Button
5. Level Adjustment Right
6. Level Adjustment Left
7. Power On/Off Button
8. Battery Removal Screws (one at each corner)
9. Battery/Electronic Box (Contains electronic board and a
Lithium-ion battery)
10. Mounting Brackets
11. Alternative Location for Mounting Brackets
12. Mini USB Port
13. Charging LED Indicator
14. Camera Housing Back Door
4
USING GYRO VISION:
1. Before using your GYRO VISION for the first time Charge battery.
The included lithium-ion battery comes partially charged. To
completely charge the unit, connect the included USB to the
GYRO and other end of the cable to a computer or a compatible
wall charger. A LED charging indicator (13) will show Red until
unit is completely charged and then turns Green in color.
(Battery life is approximately 70 Min. in normal use and varies
depending on conditions).
2. Slide power switch (7) right and observe status indicator light (3)
turn on for three seconds and then start and continue flashing
periodically as long as unit is left on and battery has charge.
3. To initialize the GYRO press and hold button (4) for three
seconds and Camera Back Door (14) will level itself relative to
the ground.
Warning:
a) For best result hold GYRO unit horizontal relative to the
ground and Do Not Move the unit until process of
initialization is complete.
b) If mounted on a motorcycle make sure the engine is OFF and
motorcycle is not moving.
4. Minor adjustment for leveling the camera is accomplished by
using Level Adjustment (5) and (6). Hold (5) to adjust level to the
right and (6) to adjust level to the left.
5
5. Open the backdoor of the housing of your camera and let it
hang downwards.
6. Pull downwards on your camera backdoor until it snaps free
from the hinge.
7. Line up the GYRO VISION camera housing back door (14) into
the hinge opening and push upwards until it clicks into place.
8. Set your camera as needed and place in the camera housing and
secure the housing back door.
Warning:
Although your camera maybe waterproof GYRO VISION unit is
NOT waterproof and should not be used in wet or damp
conditions.
9. GYRO VISION can be mounted to your camera’s mounting
bracket using your camera’s typical hardware.
10. Alternative Mounting Locations (11) can be used both on the
right and left side of the unit by relocating the Mounting
Brackets (10) from its typical location. (Removal tool is provided
with the unit).
As an option to relocating the mounting bracket, side mount
mode can be activated by pushing button (4) a second time until
Gyro unit turns the camera vertical relative to the ground. Video
recorded in this mode then needs to be edited to show
horizontal at a later time, but this should provide for a quicker
install on the road or at the track.
6
11. GYRO VISION can also be mounted in the inverted position as
needed. Follow the initialization process and make sure to set
your camera to record inverted or edit your video later.
12. It is recommended to use a cord to attach your GYRO VISION
unit to your vehicle in case a mounting bracket loosens.
GYRO VISION WARRANTY:
MOTO GYRO VISION products are guaranteed against
manufacturing defects for six (6) months from the original date
of purchase. GYRO VISION's sole obligation in the event of such
defects during this period is to repair or replace the defective
part or product with a comparable part or product at MOTO
GYRO VISION's sole discretion. Except for such repair or
replacement, the sale, processing or other handling of this
product is without warranty, condition or other liability even
though the defect or loss is caused by negligence or other fault.
Damage resulting from use, accident, or normal wear and tear
is not covered by this or any warranty. MOTO GYRO VISION
assumes no liability for any accident, injury, death, loss, or
other claim related to or resulting from the use of this product.
In no event shall MOTO GYRO VISION be liable for incidental or
consequential damages relating to or resulting from the use of
this product or any of its parts. This product does not carry any
warranty against water damage associated with use in wet or
damp conditions. Returns or replacements of parts and/or
products may be subject to shipping, handling, replacement
and/or restocking fees.
7
For Questions and / or Comments
Contact us at www.MOTOGYROVISION.com
WARRANTY REPAIR & REPLACEMENT SERVICE
INSTRUCTIONS:
MOTO GYRO VISION will replace your product or part free of charge if
your product or part has a manufacturing defect that is covered by
GYRO VISION warranty. Returns that don't qualify for warranty
coverage will be returned to customers. It is vital that you
communicate with MOTO GYRO VISION Customer Support before
sending in your return.
1. BEFORE sending anything to MOTO GYRO VISION, please
contact our Customer Support by Contact us at
www.MOTOGYROVISION.com. We often can solve the problem
quickly via email or phone call.
2. If our Customer Support determines that your problem
qualifies under warranty coverage, you will be issued a (Return
Authorization) number.
3. Prepare a package to return to MOTO GYRO VISION.
4. Write your Return Authorization number on the outside of the
box and send to the address below:
MOTO GYRO VISION
7606 Freestone Court
Rancho Cucamonga, CA 91739
(909)565-2086
8