1. No category

GRUNDFOS DATA SHEET
CME Booster
Features
•
•
•
•
•
•
Constant pressure via integrated speed control
compact, robust, stainless steel design
easy installation
dry-running protection
low noise
inlet pressure switch meeting DIN 1988-500
(optional).
p
[kPa]
1000
CME Booster
50/60 Hz
ISO 9906:2012 3B
1-99
85
80
75
70
65
60
55
50
45
40
35
30
25
20
700
600
500
400
300
200
3-93
1-75
0
5-62
3-30
5-31
10-54
15
10
5
0
100
3-62
1-44
0
0.0
1
2
3
0.5
4
1.0
5
6
1.5
10-27
7
8
2.0
9
10
2.5
11
12
3.0
13
3.5
14
15
4.0
16
17
4.5
Q [m³/h]
5.0
Q [l/s]
Selection guide
Example: sizing and selection
Find the right booster
• How many taps? 6.
• How many floors? 3.
Result: CMBE 1-75
height
12m
Tapping point
TM05 9319 3713
The compact Grundfos CME Booster is suitable for
water supply in domestic applications. The integrated
speed controller keeps a constant pressure in the pipe
system. The pressure sensor constantly monitors
changes in the discharge pressure of the pump and
changes the speed of the pump accordingly.
The optional inlet pressure switch prevents the pump
from operating in case of low inlet pressure.
The booster is very easy to install. When the booster
has been connected to the pipework, it is all a matter
of plugging the plug into a socket, and the system is
operational.
The CME Booster consists of these components:
• CME pump with integrated frequency converter
• 5-way fitting with non-return valve
• diaphragm tank
• pressure gauge
• pressure sensor
• inlet pressure switch (optional).
CMBE Booster
95
90
900
800
Fig. 1
H
[m]
115
110
105
100
1100
TM06 1039 1414
TM05 7512 3713
Performance range
Number of taps
Applications
The CME Booster is mainly used for domestic and light
commercial water supply or pressure boosting.
Application
Single-family houses
Two-family houses
Cluster houses
Blocks of flats
Schools
Small hotels/guest houses
Small office buildings
Agriculture
Irrigation
● Recommended
❍ Applicable.
CME 1
CME 3
CME 5
CME 10
●
●
●
●
●
●
●
●
❍
●
●
●
●
●
●
●
●
❍
●
●
●
●
●
●
●
●
❍
❍
❍
Number of floors
1-5
6-10
11-20
21-50
4
CMBE 1-75
CMBE 1-75
CMBE 3-62
CMBE 3-93
3
CMBE 1-44
CMBE 1-75
CMBE 3-62
CMBE 3-62
2
CMBE 1-44
CMBE 1-44
CMBE 3-62
CMBE 3-62
1
CMBE 1-44
CMBE 1-44
CMBE 3-30
CMBE 3-62
Fig. 2
Selection guide
Preconditions:
• 3 bar tap pressure. If you want 4 bar pressure, move
2 floors up in the table.
• Flooded suction and 0.5 l/s average per tap.
Demand factor has been taken into account.
Grundfos cannot be held responsible for wrong sizing
based on this guide.
Dimensional drawings
Thermal protection
Pump type
H3
H2
H1
L1
B2
A1
A2
[inch] [inch]
CMBE
CMBE
CMBE
CMBE
CMBE
CMBE
CMBE
CMBE
CMBE
CMBE
440
440
440
440
440
455
440
455
510
510
200
200
200
200
200
215
200
215
253
253
75
75
75
75
75
90
75
90
92
92
326
362
398
326
344
404
326
350
377
377
217
217
217
217
217
217
217
217
232
232
1
1
1
1
1
1
1
1
1 1/2
1 1/2
1-44
1-75
1-99
3-30
3-62
3-93
5-31
5-62
10-27
10-54
Fig. 4
Voltage
[V]
1
1
1
1
1
1
1
1
1
1
x
x
x
x
x
x
x
x
x
x
TM05 5993 4312
1
1
1
1
A
1
1
1
1
1
1
1/4
1/4
1/2
1/2
Technical data
CMBE
CMBE
CMBE
CMBE
CMBE
CMBE
CMBE
CMBE
CMBE
CMBE
MGE 0.55 to 1.5 kW
200-240
200-240
200-240
200-240
200-240
200-240
200-240
200-240
200-240
200-240
Imax [A]
P1
[W]
Plug type
3.45 - 2.9
6.7 - 5.6
6.7 - 5.6
6.7 - 5.6
6.7 - 5.6
9.1 - 7.6
6.7 - 5.6
9.1 - 7.6
6.7 - 5.6
9.1 - 7.6
615
998
1250
688
1210
1720
1090
1720
1240
1710
Schuko, US,
AU, UK or
without plug
Control panel on CME pump
Set the desired setpoint by pressing or . The light
fields on the control panel will indicate the setpoint set.
Continuously pressing
will stop the pump.
Pressing
will enable IR communication with
Grundfos GO and with other products of the same type
using IR communication.
Installation
Materials
Max. 60 °C
Material
Terminal box
Stator housing
Fan cover
Pump housing
Shaft and impeller
Flange
Composite PC/ASA and silumin (Alu)
Silumin (Alu)
Composite PBT/PC
Stainless steel, EN 1.4301/AISI 304
Stainless steel, EN 1.4301/AISI 304
Cast iron
97550802 0315
ECM: 1149152
GRUNDFOS A/S . DK-8850 Bjerringbro . Denmark
Telephone: +45 87 50 14 00
www.grundfos.com
2.5
Max.
10 bar
2
1.5
1
3
3.5
4
4.5
0/Off
5
1/On
Max. 1 m
TM063676 0215
Component
Subject to alterations.
© Copyright Grundfos Holding A/S
Dimensions
Pump type
The control panel on the E-pump terminal box makes it
possible to change the setpoint settings manually.
The operating condition of the pump is indicated by the
Grundfos Eye on the control panel. See fig. 4, pos. A.
Fig. 3
1-44
1-75
1-99
3-30
3-62
3-93
5-31
5-62
10-27
10-54
Control panel
The name Grundfos, the Grundfos logo, and be think innovate are registered trademarks owned by Grundfos Holding A/S or Grundfos A/S, Denmark. All rights reserved worldwide.
TM06 0802 0914
CME Booster pumps require no external motor
protection. The MGE motor incorporates thermal
protection against slow overloading and blocking
(IEC 34.11: TP 211).