grundfos CUE Frequency Converter grundfos cue easy installation, operation and control of pump speed maximum convenience and enhanced User interface Complete feature set opens up for many APPLICATION RELATED FUNCTIONS: Grundfos CUE offers speed control of virtually any Grundfos pump irrespective of size or area of application and is an integral part of Grundfos iSOLUTIONS. Stop function Available for constant pressure or constant level applications, the stop function stops the pump at low flow and prevents the pump from running at low flow with reduced efficiency and against closed valve with the risk of heating up the water in the pump or damaging the shaft seal. Grundfos CUE offers plug-and-pump installation and operation coupled with extensive control and monitoring possibilities. Installing and commissioning Grundfos CUE is completed in a few simple steps, where only a few application-specific settings and variables are needed to get the system running. Pump family settings Grundfos CUE offers a unique feature using pre-programmed data for different Grundfos pump families. During installation, the correct values are set for minimum speed, maximum speed, ramp times, and other pump specific settings. More than 15 parameters are set to suggested default values when the correct Grundfos pump family is selected during setup. Control mode Grundfos CUE provides a series of pre-defined application control modes: • • • • • Intuitive start up guide Grundfos CUE offers quick and easy set-up and commissioning. Simply key in application-specific variables such as motor data, pump family, control mode (e.g. constant pressure), sensor type, and setpoint, and Grundfos CUE will automatically set all necessary parameters. Constant pressure with or without stop function Proportional Differential pressure Constant level with or without stop function Constant temperature Proportional pressure These predefined control modes make it simple to program the drive for the application. When controlled from an external source, the open loop control mode is used, supplying Grundfos CUE with information about the required speed. Duty/standby Connect two Grundfos CUEs using the standard built-in GENibus interface for a duty/standby function of two pumps, with one pump as the backup for the other. extend operating range or reduce physical size of the required pump. Motors and Drive should be selected carefully to the actual load in the application. Dry-running protection Grundfos CUE offers protection against dry running, as one of the inputs can be dedicated to a variety of dry-running sensors and detectors. Advanced functions Grundfos CUE offers a series of advanced functions which can be setup by Grundfos. Contact Grundfos for more information. Over synchronous speed Over synchronous speed is an option for a series of Grundfos pumps in order to Technical specifications Control input/output connections: Four digital inputs • One dedicated input for external start/stop Remaining inputs can be set to: • Min. (min. curve) • Max. (max. curve) • Ext. fault (external fault) • Flow switch • Alarm reset • Dry running (from external sensor) • Not active Two dedicated analogue inputs One 0-10V/ - 0/4-20mA input for external setpoint. One 0/4-20 mA input for sensor feedback One analogue output Use to indicate different parameters such as speed, actual value, etc. Grundfos iSOLUTIONS is our approach to deliver the optimal combination of pumps, drives and auxiliary components for the specific application, incorporating special features and functions and building on application knowledge and experience. Easy integration of pumps, drives, measurement, controls, protection and communication into the solution combined with a high level of customisation, compactness and preset units saves engineering, installation and commissioning time. Learn more on grundfos.com/isolutions Two digital relay outputs Can be set up to report information such as operation, warnings and alarms. RS485 Genibus interface Grundfos CUE is equipped with a standard RS485 interface that can communicate with Grundfos control systems, and via a Grundfos gateway be connected to other bus systems for example LONworks, Profibus, Modbus by using Grundfos CIU. Accessories Control mode Proportional pressure H duty/standby Constant level L CUE CUE CUE 1 GENIbus CUE 2 L Q Q temperature control H CUE constant pressure H Duty CUE p Q Q Standby MCB 114 sensor input module • One additional 0/4-20 mA input for sensor • Two Pt100/1000 inputs to be used in connection with motor bearings temperature measurement, or alternative temperature measurement such as the media temperature Motor filters Two different types of motor filters are available: • dU/dt filters for limiting the rise time of the output of the drive to approximately 500V/us • Sine wave filters, to create a sine wave of the output voltage, limiting both Upaek and dU/dt to values comparable to mains supply 98848178 0215/PRODUCT LINE MANAGEMENT/11735-D&I Power supply 7.5-250 kW 3 x 525-690 V 0.75-7.5 kW 3 x 525-600 V 0.55-250 kW 3 x 380-500 V 0.75-45 kW 3 x 200-240 V 1.1-7.5 kW 1 x 200-240 V 0.3 1 3 10 30 100 250 EMC filter for conducted emission according to IEC61800-3 Ed. 2. • CUE rated 500V or lower up to 90kW: Build-in filter for household application (class C1) • CUE rated 500V or lower above 110kW: Build-in filter for industrial application (class C2) • CUE rated 525V or more independent of power size: Build-in filter for industrial application (class C3) Grundfos Holding A/S Poul Due Jensens Vej 7 DK-8850 Bjerringbro Tel: +45 87 50 14 00 www.grundfos.com kW The name Grundfos, the Grundfos logo, and be think innovate are registered trademarks owned by Grundfos Holding A/S or Grundfos A/S, Denmark. All rights reserved worldwide. Product Range
© Copyright 2024