1. No category

Install Guide
Sola Cam locking
Code & Key Managed
IMPORTANT:
Do not operate and turn the handle to the unlocked position without first installing the lock or
determining whether the lock is for a left or right handed configuration.
Lock Orientation - Views
Vertical Installation
SOLA can be installed for left or right handed configuration.
Horizontal Left Handed Installation
Locked Position
Unlocked Position
Horizontal Right Handed Installation
Locked Position
Unlocked Position
Cam & Cam Stop Position
Locked Position
Unlocked Position
Note: The position of the cam and cam stop varies depending on whether it is
vertically or horizontally installed for a left or right handed configuration.
Vertical Back View
Horizontal Left Handed Back View
Horizontal Right Handed Back View
Cam throw: right
Cam throw: top
Cam throw: top
Locked Position
Unlocked Position
Cam throw: left
Locked Position
Locked Position
Unlocked Position
Cam throw: bottom
Unlocked Position
Locked Position
Locked Position
Unlocked Position
Cam throw: bottom
Unlocked Position
Locked Position
Unlocked Position
Phone: 707 766 6000
www.digilock.com | [email protected]
Install Guide
Sola Cam locking
Code & Key Managed
IMPORTANT:
Do not operate and turn the handle to the unlocked position without first installing the lock or
determining whether the lock is for a left or right handed configuration.
Hardware & Mounting
thickness: 0.1–5mm (.01”-.197”) B Door thickness: 6-10mm (.236”-.394”)
A Door
Use upper nut hardware
Use upper screw hardware
Sola Lock
Sola Lock
Lock Base Seal
Sola Lock
Lock Base Seal
Flat Washer
Flat Washer
Nut
Lock Base Seal
Flat Washer
Nut
Star Washer
Star Washer
Philips Screw
(M5 Pan Head)
Philips Screw
(M5 Pan Head)
Cam Stop*
11-14mm Door
14-18mm Door
18-22mm Door
Cam Stop*
Cam Stop*
*Refer to section on Cam
and Cam Stop Position
*Refer to section on Cam
and Cam Stop Position
*Refer to section on Cam
and Cam Stop Position
Cam
Cam
Cam
Flat Washer
Star Washer
Nut
Flat Washer
Philips Screw (M5 Pan Head)
thickness: 11-22mm (.433”-.866”)
C Door
Use upper screw hardware
Flat Washer
Star Washer
Nut
Flat Washer
Philips Screw (M5 Pan Head)
Flat Washer
Star Washer
Nut
Flat Washer
Philips Screw (M5 Pan Head)
Phone: 707 766 6000
www.digilock.com | [email protected]
20mm
NOTE: For the cam/latch to effectively secure,
the strike plate must fall within the gray area
110mm
Warning: this template may not be to scale
NOTE: For the cam/latch to effectively secure,
the strike plate must fall within the gray area
Use this reference line to align template to the edge of your door frame
Use this reference line to
align center of strike plate
Install Guide
Sola Cam locking
Code & Key Managed
Drill Template
Templates may not print to scale. Check all measurements before proceeding.
Before printing, turn off auto scaling in printer setup and print at 100%.
Printer settings:100%
Do not set shrink to fit
Top Hole
13mm
Existing Hole
Phone: 707 766 6000
www.digilock.com | [email protected]
Edge of
Door Frame
Drill Instructions
Center of
Strike Plate
Door Frame Marker
Install Guide
Sola Cam locking
Center of
Strike Plate
Code & Key Managed
Door Frame
Edge of
Door Frame
Center Line
Center Line
For illustration, the mounting holes template for vertical body lock is used.
2
Edge of
Door Frame
Center of
Strike Plate
Door Frame Marker
1
Mark The Door Edge
On The Template
Door Edge
Center Line
Drawn
Marker
Marktemplate
The Door Edgewith the center
Align the center line of the
On The Template
of the installed strike plate.
Hold or tape the template in place and close the
door.
Mark The Door Edge
On The Template
Mark the edge of the door on the template. Mark
the center line of the template on the edge of the
door.
Door Edge
Drawn
Marker
3
4
Door Edge
Drawn
Marker
Mark The Door Edge
On The Template
Mark center
with a punch
Mark center
with a punch
Door Edge
Place the template on the front of the door.
Drawn
Align the edge
Marker of the door with the mark you created
on the template, and then align the center line of the
template with the mark on the door.
Secure the template with removable tape.
Drill the two openings according to the measurements shown on the template. Mark center
Top hole 1/2 inch (13 mm)
Bottom hole 3/4 inch (20 mm)
with a punch
Mark center
with a punch
Mark center
with a punch
Mark center
with a punch
Phone: 707 766 6000
www.digilock.com | [email protected]
Install Guide
Sola Cam locking
Code & Key Managed
Install Instructions
1
2
3/4” Flat Washer
3/4” Nut
Insert the front unit throught the two mounting
holes on the door. (See door prep)
Holding the unit in place and take the appropriate
mounting hardware for your door thickness.
A) 1/2 inch flat washer and nut hardware
B) 1/2 inch nut and screw hardware set
C) screw hardware set
3
4
Flat Washer
Philips Pan Head Screw
11-14mm Door
14-18mm Door
18-22mm Door
Star Washer
Cam
Flat Washer
Philips Pan Head Screw
Star Washer
Stop
Take the 3/4 inch flat washer and nut hardware and
secure the bottom cam shaft to the door.
The positon of the cam and cam stop varies
depending on the lock orientation. Please refer to the
Cam & Cam Stop Position chart.
Phone: 707 766 6000
www.digilock.com | [email protected]
Install Guide
Sola Cam locking
Code & Key Managed
5
Once you determine the orientation of your cam,
secure the cam with the small screw hardware set.
032515
IG-NMSU-U-DEN
Phone: 707 766 6000
www.digilock.com | [email protected]