1. No category

Accessories
Position Sensor Model TRS
Type 2112A...
with Internal Return Spring for Displacement, Tolerance
Measurements and Continuous Position Sensing
Displacement sensor with resistance and collector path of
conductive-plastic – with internal return spring – for direct
displacement and tolerance measurements and for continuous
position sensing.
•
•
•
•
•
Long life: 100x106 movements
Outstanding linearity up to 0,075 %
DIN standard gauging end
Double bearing system on shaft
Insensitive to shock and vibration
Housing
Actuating rod
Description
An important and special feature of these particular units are
their robust, industry-proven design. Of particular significance
is the double bearing arrangement which is really useful when
side forces are met. The rear end of the actuating rod has a
special collar, which can be easily employed where automatic
retraction by means of air cylinders or solenoid is required.
Aluminium, eloxiert
stainless steel with anti-rotation device, inside
thread M2,5
Gauging head
stainless steel with external M2,5 thread and
hardened ball point
Resistance element conductive plastic
Wiper assembly
precious metal multi-finger wiper,
elastomer-damped
Electrical
5-pin round connector IEC 130-9
connection
2112A_000-868e-05.11
Technical Data
Model
Electrical Data
Defined electrical range
Nominal resistance
Linearity, independent
Repeatability
Max. permissible applied voltage
Recommended operating wiper current
Max. wiper current in case of malfunction
Mechanical Data
Overall length (dimension A+1 mm)
Mechanical stroke (dimension B+1,5 mm)
Weight
Operating force (horizontal)
Operating frequency
Environmental Data
Temperature range
Vibration
Shock
Protection class (EN 60529)
TRS25
TRS50
TRS75
TRS100
mm
kΩ
±%
mm
V
<μA
mA
25
1
0,2
50
5
0,15
75
5
0,1
100
5
0,075
mm
mm
g
≤N
Hz
63
30
74
94,4
55
100
134,4
80
128
166
105
150
18
14
11
10
0,002
42
1
10
5
°C
Hz
g/ms
IP
–30 ... 100
5 ... 2 000
50/11
40
Important: All values specified in this data sheet for linearity, lifetime and temperature coefficient are only valid for a sensor used as a voltage divider with
virtually no load applied to the wiper (le ≤0,1 μA).
Page 1/2
This information corresponds to the current state of knowledge. Kistler reserves
the right to make technical changes. Liability for consequential damage resulting
from the use of Kistler products is excluded.
©2010 ... 2011, Kistler Group, Eulachstrasse 22, 8408 Winterthur, Switzerland
Tel. +41 52 224 11 11, Fax +41 52 224 14 14, [email protected], www.kistler.com
Kistler is a registered trademark of Kistler Holding AG.
Position Sensor Model TRS – with Internal Return Spring for Displacement, Tolerance
Measurements and Continuous Position Sensing, Type 2112A...
Dimensions
Schematic
1
5 1
3
2
1
+1,5
2
40
28,8
+0,3
1
3
8,2
19
41,8
Included Accessories
• 2 mounting clamps Z-45
incl. 4 allen screw M4x10
• 1 gauging head with hardened
ball point
+0,4
1,6
18
2
2,4
B
SW 10
7,2
Accessories (Optional)
• Connecting cable for
CoMo Net®/View®/Sys
• Connecting cable for DMF-P family
• Connecting cable for maXYmo family
• Connecting cable for SigMo Sys
Type
1200A151Asp
1200A151Bsp
1200A151Csp
1200A151Dsp
12
Ordering Key
Type 2112A
25
50
75
100
32
atbei
end
position
Endposition
B
5
2112A_000-868e-05.11
10
2/3A
recommended
distance
empfohlenes
Abstandsmass
A
10
Position Sensor TRS
25 mm
50 mm
75 mm
100 mm
Page 2/2
This information corresponds to the current state of knowledge. Kistler reserves
the right to make technical changes. Liability for consequential damage resulting
from the use of Kistler products is excluded.
©2010 ... 2011, Kistler Group, Eulachstrasse 22, 8408 Winterthur, Switzerland
Tel. +41 52 224 11 11, Fax +41 52 224 14 14, [email protected], www.kistler.com
Kistler is a registered trademark of Kistler Holding AG.
