1. style and fashion
2. accessories
3. gloves

IF YOU DON’T SEE IT IN OUR CATALOG CALL 800.742.8054
Tool & Safety
ARC FLASH PROTECTION
Page 7
TO ORDER: 800.742.8054 • FAX: 866.524.4885 • www.irby.com
Tool & Safety
SALISBURY PRO-WEAR™ ARC FLASH KITS
SKJ Kit
Jacket w/hood
and AS1000 Hat
HRC2
Important safety information - We provide easy to order, comprehensive and
convenient protection kit options. Determine your PPE cal/cm2 rating based on the
severity of the arc hazard and use the table below as a guide. Always perform a
hazard assessment.
Arc Protection Clothing Requirements - OSHA 29 CFR 1910.269 (1)(6)(iii) “The
employer shall ensure that each employee who is exposed to the hazards of flames
or electric arcs does not wear clothing that, when exposed to flames or electric arcs,
could increase the extent of injury that would be sustained by the employee. Clothing
selected for a particular application shall have an arc thermal performance value of
(EBT or ATPV) higher than the potential hazard to prevent the onset of 2nd degree
burns.
NFPA 70E-2004 addresses electrical safety-related work practices and procedures for
employees who work on or near exposed, energized electrical conductors or circuit
parts. This standard requires employees to wear flame resistant (FR) protective clothing
that meets the requirements of ASTM F1506 wherever there is possible exposure to
an electric arc flash. While OSHA has not formally adopted this standard, they will
cite employees under the general duty clause and make reference to NFPA 70E.
NFPA 70E 2004 Edition - Table 130.7(C) (11) Protective Clothing Characteristics
Typical Protective Clothing Systems
SKCA Kit
Coveralls and
AS1000 Hat
HRC2
Salisbury
Clothing
Color Code
Navy
Blue
Hazard Risk
Category
(HRC)
Clothing Description
(Typical number of clothing
layers given in parentheses)
Minimum Arc Thermal Performance
Exposure Value (ATPV)** or Breakopen
Threshhold Energy (EST)* Rating of PPE
0
1
Untreated Cotton (1)
n/a
2
Cotton Underwear Plus FR
Shirt and FR Pants (1 or 2)
Royal
Blue
3
Gray
4
FR Shirt & FR Pants (1)
4 cal/cm2 (16.74 J/cm2)
8 cal/cm2 (33.47 J/cm2)
Cotton Underwear Plus
FR Shirt and FR Pants
Plus FR Coverall (2 or 3)
25 cal/cm2 (104.6 J/cm2)
Cotton Underwear Plus FR
Shirt and FR Pants Plus
Double Layer Switching
Coat and Pants (3 or more)
40 cal/cm2 (167.36 J/cm2)
HRC LEVEL 2 KITS INCLUDE:
• 8, 11, or 20 cal/cm2 Protective Clothing
• AS1000 Hat or Pro-Hood w/Hard Hat
• 11” Class 0 or 00 Rubber Insulating Gloves
SKJP Kit
Jacket w/hood,
overpants and
AS1000 Hat
HRC2
Page 8
• 10” Leather Protectors
• Safety Glasses
• Glove Bag
• Large Storage Bag
IF YOU DON’T SEE IT IN OUR CATALOG CALL 800.742.8054
Tool & Safety
SALISBURY PRO-WEAR™ ARC FLASH KITS
HRC LEVEL 3 KITS INCLUDE:
HRC LEVEL 4 KITS INCLUDE:
• 31 cal/cm2 Protective Clothing
• 40 cal/cm2 Protective Clothing
• Pro-Hood w/Hard Hat
• Pro-Hood w/Hard Hat
• 11” Class 0 or 00 or 14” Class 2 Rubber
Insulating Gloves
• 14” Class 2 Rubber Insulating Gloves
• 10” Class 0 or 00 or 12” Leather Protectors
• 12” Leather Protectors
• Safety Glasses
• Safety Glasses
• Glove Bag
• Glove Bag
• Large Storage Bag
• Large Storage Bag
Description
ATPV Rating cal/cm2 Glove Color Glove Class
(COAT, BIBS,
PRO HOOD)
SK
SK
SK
(JACKET W/HOOD,
AS1000 HAT)
SKJ
(JACKET W/HOOD,
OVERPANTS
AS1000 HAT)
SKJP
(COVERALLS,
KNIT HOOD,
AS1000 HAT)
SKCA
Example:
SKJ
SK Kit
SK20 w/Pro Hood
HRC2
Glove Size Clothing Size HRC
8,11,20
31
40
R,L,B,Y
R,L,B,Y
B
00, 0
00, 0,2
2
8-12
8-12
8-12
S-3XL
S-3XL
S-3XL
2
3
4
8 or 11
R,L,B,Y
00, 0
8-12
S-3XL
2
8 or 11
R,L,B,Y
00, 0
8-12
S-3XL
2
8 or 11
R,L,B,Y
00, 0
8-12
S-3XL
2
0
9
11
Y
SK Kit
SK31 w/Pro Hood
HRC3
L
SKJ11Y09L is a clothing kit containing a large arc flash jacket in an ATPV rating of 11 cal/cm2, AS1000HAT, yellow
Class 0 gloves in size 9, the appropriate leather protector gloves and glove bag, storage bag and safety glasses.
Class 00 Gloves in R, B, or L only, Class 0 Gloves in R, B,
Y, or L Type I Natural Rubber available in: R=Red,Y=Yellow,
B=Black, Type II Salcor Rubber available in: L=Blue Class
2 gloves in B = Black, Type I Natural Rubber only
Important: The maximum Arc Flash Protection
of a kit is equal to the lowest cal/cm2 rating of any
component in the selected safety kit.
All items shown are also available separately.
Arc Flash Clothing Sizing Chart
Coveralls
Jackets and Coats
Bib Overalls and Overpants
Chest
Size
Waist
Size
Inseam
Chest
34-36”
S
28-30”
S
28”
34-36”
S
38-40”
M
32-34”
M
29”
38-40”
M
29”
42-44”
L
36-38”
L
30”
42-44”
L
30”
30”
46-48”
XL
30”
2XL
30”
3XL
30”
46-48”
XL
40-42”
XL
50-52”
2XL
44-46”
2XL
30”
50-52”
54-56”
3XL
48-50”
3XL
30”
54-56”
Size
Inseam
28”
SK Kit
SK40 w/Pro Hood
HRC4
Page 9
TO ORDER: 800.742.8054 • FAX: 866.524.4885 • www.irby.com
Tool & Safety
SALISBURY PRO-WEAR™ ARC FLASH
PROTECTIVE CLOTHING AND ACCESSORIES
Coveralls 8 - 20 cal/cm2 ATPV, made from arc flash resistant, Indura Ultra Soft®,
Sewn with Nomex® thread and Full cut with set in sleeves. Complete with FR hook
and pile front closure and 30” inseam, 2-ply Nomex® wristlets and a hook and pile
cuff openings.
Protective Jackets and Overpants 8 - 20 cal/cm2 ATPV, made from arc flash
resistant, Indura Ultra Soft®, Sewn with Nomex® thread. Jackets are 32” long and
have Nomex® wristlets, hook and a pile front closure and are intended to be used with
Salisbury PRO-SHIELD™(AS1000 Hat). Overpants have full elastic waistband,
FR hook and pile front closure, 30” inseam and a hook and pile cuff adjustment. The
loose design and flared legs make it easy to put on and take off over existing work
clothing.
ACCA
Coveralls
Order Code
Color
Size
8 cal/cm2, Indura Ultrasoft®
11 cal/cm2, Indura Ultrasoft®
20 cal/cm2, Indura Ultrasoft®
Navy Blue
Navy Blue
Navy Blue
SM-3XL
SM-3XL
SM-3XL
JACKET W/HOOD
JSHV832BL
8 cal/cm2, Indura Ultrasoft®
JSHV1132BL
11 cal/cm2, Indura Ultrasoft®
JSHV2032BL
20 cal/cm2, Indura Ultrasoft®
Navy Blue
Navy Blue
Navy Blue
SM-3XL
SM-3XL
SM-3XL
OVERPANTS
ACP830BL
ACP1130BL
ACP2030BL
Navy Blue
Navy Blue
Navy Blue
SM-3XL
SM-3XL
SM-3XL
COVERALLS
ACCA8BL
ACCA11BL
ACCA20BL
JSHV
Jacket w/Hood
Description
8 cal/cm2, Indura Ultrasoft®
11 cal/cm2, Indura Ultrasoft®
20 cal/cm2, Indura Ultrasoft®
Coveralls, Jackets and Overpants meet current ASTM F1506 and NFPA 70E standards.
ACP
Overpants
Page 10
IF YOU DON’T SEE IT IN OUR CATALOG CALL 800.742.8054
Tool & Safety
NATIONAL SAFETY APPAREL (NSA) LAB COAT AND LEGGINGS
Long Lab Coat, C04UP - is calf length 42” or 49” and is made from 9 oz Indura
Ultra Soft fabric. Features an FR Velcro front closure and FR knit wrists.
Leggings, L05UP - are 14” long and wrap-around with FR Velcro closures. Leggings
come in standard sizes of XL (191/2” width) or 2X (211/2” width). Made from 9 oz
Indura Ultra Soft fabric.
Order
Code
Description
Color
Size
L05UP
Leggings
LAB COAT AND LEGGINGS
C04UP
11 Cal/cm2, Long Lab Coat, Indura Ultra Soft
Navy Blue
SM-3XL
L05UP
11 Cal/cm2, Leggings, Indura Ultra Soft
Navy Blue
XL, 2XL
C04UP
Longcoat
DIELECTRIC OVERSHOES
Dielectric Footwear - 21405, 21406 (shown) and 51508, 51509 (not shown),
provide extra safety when climbing ladders and poles where the deep heel cavity
can lock onto the rungs. Includes an adjustable side strap. Are 100% water-proof
and made from premium grade ozone resistant rubber. The fabric lining makes them
easy to get on and off. The sole has a durable construction with a non-skid bar tread
outsole. The attached buckle and hardware is non-metallic. Salisbury Dielectric
Footwear conforms with ASTM F1117 and the entire boot is 100% tested to
ASTM F1116 at 20,000 volts.
Super Dielectric Deep Heel Overshoes - 21402, 51581 and 51530 provide extra
safety when climbing ladders and poles where the deep heel cavity can lock onto
the rungs. Includes an adjustable side strap. Are 100% water-proof and made from
premium grade ozone resistant rubber. The fabric lining makes them easy to get
on and off. The sole is an anti-skid bar thread. The out sole of these overshoes
and boots have been tested to 20,000 volts to the electrical hazard requirements of
ASTM F2413-05.
Order Code
Description
21405
17” Full Cut
21402
17” Full Cut
Size
DIELECTRIC OVERSHOES
21405
17” height full cut 21406 12” height full cut
51508
Storm rubber slip on (not shown)
51509
Storm rubber 2” buckle (not shown)
7 - 17
7 - 17
7 - 17
7 - 17
SUPER DIELECTRIC OVERSHOES
21402
17” height full cut
51581
Storm rubber slip on
51530 Storm rubber 2” buckle
7 - 17
7 - 17
7 - 17
Overshoes available in full sizes only.
21406
12” Full Cut
51581
Slip-on
51530
2-Buckle
Page 11
TO ORDER: 800.742.8054 • FAX: 866.524.4885 • www.irby.com
Tool & Safety
ARC FLASH PROTECTIVE CLOTHING AND ACCESSORIES
Salisbury Proshield™, AS1000HAT, 10 cal/cm2 ATPV Rating when used with the
included chin cup, 8 cal/cm2 without the chin strap. The 70% light transmissionshield has a 7.5” x 20” viewing area and extra light tint, it is .06” thick and absorbs
99.9% of harmful UV radiation. It is also resistant to fogging and is tested to ASTM
F2178 specifications.
Salisbury’s Balaclava Hoods, Salisbury’s Arc Flash Hoods (balaclava) create
360º head and neck protection from arc flash dangers, when used with Proshield™.
AFHood10, has an ATPV rating of 10 cal/cm2 and is made from 20% Nomex® and
80% Lenzing FR® materials. AFHOOD15 has an ATP rating of 15 cal/cm2 and is
made from 100% Nomex, AFHOOD20 has an ATPV rating of 20 cal/cm2 and is
made from 100% NOMEX®.
AS1000HAT
Safety Glasses, TS56505, are anti-fogging, anti-scratch and anti-static with 99.9%
UV protection. These glasses meet current ANSI Z87.1, 2003 and CSA Z94.3
standards. Available in clear, amber or smoke lens.
ASBAG
Proshield Storage
Steel Grip Protective Head Gear, 4692, includes a face shield with protective chin
cup, slotted vision/adaptor and dielectric hard hat and has a 10 cal/cm2 ATPV rating.
Meets ANSI 287.1 standards.
Order Code
TS56505
Safety Glasses
AFHOOD15
PROSHIELD AND ACCESSORIES
AS1000AS1000FS shield w/ASCP chin cup and slotted ASSLB
bracket. Fits most slotted front brim hard hats
AS1000FBAS1000FS shield w/ ASCP chin cup and universal
FBBracket. Fits most full brim hard hats
AS1000HAT
AS1000 w/ SA29R front brim hard hat
AS1000FS
Replacement Shield for AS1000HAT, AS1000FB and AS1000.
SA29Type I, Class E, dielectrically rated front brim hard hat
w/quick-fit 4 point suspension, white, yellow or orange
SA29RType I, Class E, dielectrically rated front brim hard hat
w/ratchet 4-point suspension, white, yellow or orange
STEEL GRIP
4692
SKBAG
Arc Flash Storage
Page 12
Protective Helmet and Shield
BALACLANA HOOD AND HAIRNET
AFHOOD1010 cal/cm2, 20% Nomex® 80% Lensing FR®, white
AFHOOD1515 cal/cm2, 100% Nomex® white
AFHOOD2020 cal/cm2, 40%P84®, 55%, navy blue
HN-1FR protective Hairnet, Nomex®, gray
SAFETY GLASSES
TS56505GRY
TS56505GRYA
TS56505GRYS
4692
Steel Grip
Protective Helmet
Description
Clear lense, gray frame
Amber lense, gray frame
Smoke lense, gray frame
STORAGE BAGS
ASBAGFleece interior, cotton canvass storage bag w/drawstring
closure for PRO-SHIELD™ series products
SKBAGLarge storage bag for Arc Flash clothing, gloves and
other accessories. Bag is 24” x 15” x 12”
IF YOU DON’T SEE IT IN OUR CATALOG CALL 800.742.8054
Tool & Safety
SALISBURY ARC FLASH PROTECTIVE HOODS
Provides 8 cal/cm2 to 40 cal/cm2 Protection. Hoods are made from arc flash resistant,
Indura Ultra Soft® sewn with Nomex® thread Arc rated 10” x 20” anti-fogging
replaceable lens, slotted bracket, hook and pile tabs to attach Salisbury’s PRO-AIR™
belt mounted compact air system, one size fits all. Hard hat not included. Meets
current ASTM F2178 and NFPA 70E standards and the flammability requirements
for ASTM F1506.
Order Code
Description
Color *VLT
FH20BL
Salisbury Hood
SALISBURY PRO-HOOD
FH20BL 20 cal/cm2, Indura Ultra Soft
Navy Blue
55%
FH31RB
31 cal/cm2, Indura Ultra Soft
Royal Blue
55%
FH40GY
40 cal/cm2, Indura Ultra Soft
Gray
55%
Gray
55%
*VLT = Visual Light Transmission
STEEL GRIP HOOD
AG40H-A
40 cal/cm2, includes hood,
cooling system, hard hat,
tinted lens
ELECTROMARK WARNING LABELS
Flash Protection requires labeling on switchboards, panel-board, MCCs and
industrial control panels so that electrical workers are made aware of the potential
hazards and can take appropriate action. Lables are self-adhesive and made from
tear-resistant polyester film for superior performance. The enhanced label features
write-on coating and self-laminating flap to protect and secure written information.
Order Code
Description
FH31RB
Salisbury Hood
Size (in.)
ARC FLASH WARNING LABELS
E12075
Standard Arc Flash Label
3.5” x 5”
E12076
Standard Arc Flash Label
5” x 7”
E12077
Enhanced Arc Flash Label
3.5” x 5”
E12078
Enhanced Arc Flash Label
5” x 7”
E12075 or E12076
Standard
E12077 or E12078
Enhanced
FH40GY
Salisbury Hood
AG40H-A
Steel Grip Hood
Page 13
TO ORDER: 800.742.8054 • FAX: 866.524.4885 • www.irby.com
Tool & Safety
SALISBURY INSULATED TOOLS
1000 VOLT - KITS
Salisbury’s Insulated Tool Kits meet IEC 900 Standards for insulated hand tools.
Every insulated hand tool is rated for exposure up to 1000VAC and dielectrically
tested at 10,000VAC. These tools meet or exceed ASTM F1505-01 and IEC 900
Standards for insulated hand tools. These tools are necessary for compliance with
OSHA 1910.333 (c)(2), and NFPA 70E 2004.
TK9
9-piece
Tool Roll
The insulating material used in all Salisbury Insulated Tools is impact resistant
and flame retardant. Two-color insulation make inspection easier which adds to the
overall safety of the user. If the yellow under layer is showing, the tool may no
longer be insulated properly, should be considered for replacement and removed
from service.
Order Code
Description
SALISBURY INSULATED TOOLS
TK9
Basic 9-Piece Electrician Tool Roll
TK30
Deluxe 30-Piece Maintenance Tool Kit
TK60
Hot Box 60-Piece Tool Kit
Please call for additional information regarding tool kit specifications and components.
TK30
30-piece
Tool Kit
TK60
60-piece
Tool Kit
Page 14