PL-TP01 - 30/55/70/80W WEATHER PROOF SERIES Description: PrimeLED Weather Proof is an advanced linear LED design, with low glare diffused lens and a 230 degree beam angle. With an IP65 rating, and IK10 impact rating. The PrimeLED weather proof range is designed for harsh enviroments. Electrical Specification: •Input Voltage: AC100-277V/50-60Hz •Input Current: 0.55A Max •Power: 30W/55W/70W/80W •lifespan: 50,000 Hours •Materials: Aluminium alloy and PC •Use Enviroment: 20C - 45C •Protection against electric shock: Level 1 Patented CRI >80 Ik10 650℃ Glow-Wire 5 Application: •Warehouse •Workshops •Carparks •Refrigerator •Freezer •Security •Lighting Specifications (By Order): Model CCT Colour LED Quantity Beam Angle Volatage (V DC) Power(W) Length(mm) PL-TP-30-CW 5500k White 252 2835 SMD LED 2750 230o 100-277 30 603*106 PL-TP-30-NW 4000k Natural White 252 2835 SMD LED 2750 230o 100-277 30 603*106 PL-TP-55-CW 5000k White 420 2835 SMD LED 5100 230o 100-277 55 55 1003*105 PL-TP-55-NW 4000k Natural White 420 2835 SMD LED 4990 230o 100-277 55 1003*105 PL-TP-70-CW 5000k White 480 2835 SMD LED 6910 230o 100-277 70 1203*105 PL-TP-70-NW 4000k Natural White 480 2835 SMD LED 6840 230o 100-277 70 1203*105 PL-TP-80-CW 4000k White 600 2835 SMD LED 7580 230o 100-277 80 55 1503*105 PL-TP-80-NW 4000k Natural White 600 2835 SMD LED 7600 230o 100-277 80 1503*105 PrimeLED Australia Warehouse / Showroom LED Type Lumens Unit 2, 99-101 Western Ave Westmeadows VIC 3049 1300 533 000 (1300 LED 000) [email protected] www.primeled.com.au 3 Years warranty Dimension drawing (unit:mm/inch): 603/1003/1203/150 106 4.17" 72 2.83" Installation Information: 1. First set up accessories and fittings of the light. 2. Cut off the power before installation. 3. Make sure the product is fixed tightly to the installation surface (Install it according to diagram below). 4. Connect the wire of the light tot he power supply, then switch on the power. Intallation Method I Size:(mm) 55mm 580mm 1. Drill 4 holes of 8mm diameter. screw 2. Install the holder on the wall, be attention that the direction should be the same. 3. Turning the screw but not tightly, leave 3-4mm space. 4. Install the light and tighten the screw. Intallation Method II Size:(mm) 604 Screw 1.Drill 4 holes of 6.5mm. 2. Install the clip onto the wall. 3. Use screws to conenct the hanging ring with screw holes on both sides of the lamp. 4. Adjust the height of the wires of both sides. Safety Information: Important Safety Instructions 1. Turn off the main power supply prior to installation. 2. The light fitting must be installed by a licensed electrial contractor or electrician. 3. If there is any visible damage on power cord or the shell of the product, it should not be used. Cleaning and Maintenance Turn off the power supply. Clean the Ceiling Light with soft cloth using a mild liquid cleaner. Dry with a cloth. PrimeLED Australia Warehouse / Showroom Unit 2, 99-101 Western Ave Westmeadows VIC 3049 1300 533 000 (1300 LED 000) [email protected] www.primeled.com.au 3 Years warranty
© Copyright 2024