A-1 Jukebox & Nostalgia, Inc.
Exclusive distributor of “Ken Arnold brand”
and other “Exact”
Reproduction Parts for Jukeboxes
Complete 2010/2011 Catalog
Please note that the number pages of our Online Catalog may be different
than the number of pages of our Printed, (hard copy) Catalog.
This is because the format, (mainly the line spacing), may differ between the two.
Extremely Important:
Before You Plug It In
When you first acquire a jukebox, any year, any make, any model, here are a few things that
must be done before you plug it in:
1. Remove, inspect, (replace if blown or reinstall if good), each of the Fuses. Do this one
fuse at a time. Make sure that the Amperes of each fuse and the type, such as: AGC,
Slo-Blo, MDL, etc., is the precise rating or (Amps.), and the precise type that is printed
on the chassis next to each fuse holder.
2. For ALL Seeburg Wired Selection Receivers in models M100A through 100JL, if wall
boxes, (Diner booth selector units), such as 3W-1, etc. are not going to be used, locate
or have a jukebox technician locate the 5 Mfd. @ 300 volts capacitor. Clip the two wires
going to one side of this capacitor. Twist or solder and then tape these two wires
together and secure them somehow so that they do not come in contact with the other
parts of the WSR circuit. This procedure takes that old original capacitor out of the
circuit. If wall boxes are going to be used, be sure to replace this capacitor with a fresh,
new one. Doing this will help save the transformer in the WSR. (Most of these capacitors
are shorting out causing the transformer in the WSR’s to burn out. Replacement
transformers, for the WSR’s, are approximately $200.00, when you can find them!)
3. For Seeburg’s: “SOME” Amplifiers, Receivers, Selector Units, Control Centers and other
components are interchangeable. In other words: It is possible for a Seeburg Jukebox to
have a different “Component Part Model Number” than is listed in the Service and Parts
manual. If you have any questions about this, Please give us a call or send us an Email.
A-1 Jukebox & Nostalgia, Inc.
208 South Pulaski Street Suite 4J
Baltimore, MD 21223-2952
Phone 410-945-8900
Fax 410-945-1946 (Fax only)
Email: [email protected]
Before calling for Parts or Service
-1-
1. Know the Make and Model number of your Jukebox. The serial number of a Jukebox
usually means nothing to us parts guys. The Make and Model number plate is always
located on the back of the Jukebox unless someone has removed it. Also, know the
model number of the Amplifier and the Wired Selection Receiver or other unit that you
will be inquiring about. Component parts of some Jukeboxes are interchangeable,
however, they are never exactly alike, (If you need parts or service for a component part
of your Jukebox we will need to know the specific model number of the component part
before we can help you).
2. When ordering replacement needles, (Styli), try to establish if the Cartridge, that hold the
needle(s), is the original cartridge or a replacement. In most cases the cartridge will have
some identifying characteristics on it. If you cannot identify the cartridge type, we request
that you remove the needle and copy the shape of the needle on a copier. Then fax or
mail the copy to us. What works even better is if you have a digital camera, take a digital
picture of the cartridge and needle and email the picture to us, (If using a digital camera,
it is not necessary to remove the needle from the cartridge).
Acknowledgment
Once again, we would like to take this opportunity to thank Ken Arnold for his many years of
dedication to his business, which for more than a decade was the manufacturer and sales of
exact reproduction parts for antique Jukeboxes. Ken still cuts, shapes and prints most of the
glass and plastic cabinet parts that are listed in this catalog.
As the exclusive distributor of “Ken Arnold brand” reproduction Jukebox parts we extend Ken’s
policy on all of the parts that he manufacturers:
“The best Quality and Guarantee in the business”.
For Your Safety, Ken sands the edges of all of the glass parts that he manufacturers.
To ensure Originality, All colors have been formulated to match factory colors. Font
styles have been regenerated by hand or by computer and Ken personally screen-prints
in his own shop.
To ensure correct Fit, all Ken Arnold brand parts are manufactured to factory standards
using original samples.
Unconditional Customer Satisfaction: Every part manufactured by Ken is guaranteed to
be free of manufacturing defects for 5 years.
Copyright © 2003, 2009 & 2010
A-1 Jukebox & Nostalgia, Inc.
Exclusive distributor of “Ken Arnold brand”
and other “Exact” reproduction Jukebox Parts
-2-
How to Order:
Phone orders from 10:00 am to 6:00 pm (Eastern time) Monday through Friday.
Phone 410-945-8900.
Fax orders anytime 7 days a week: Fax 410-945-1946. FAX transmissions ONLY.
Email orders to: [email protected] and please include your ship-to address and phone numbers so
we can contact you, by phone, if necessary.
Mail orders to: A-1 Jukebox & Nostalgia, Inc: 208 S. Pulaski Street Suite 4J Baltimore, MD 21223-2952.
Secure On-line ordering will be available as soon as possible. Please visit our
web site: jukeboxusa.com for a complete list of jukebox parts, records and accessories.
Visit our warehouse In Person. Please call us in advance for directions. We enjoy meeting our customers.
Privacy and Security: The information that we have on file for our customers is held in the strictest
confidence. We do not and will not sell or pass any customer private information to anyone at anytime for
any reason!
Shipping: For orders weighing one pound or less we ship via US Postal Service, (unless otherwise
requested). For orders weighing over one pound we ship via UPS ground service, (unless otherwise
requested). Faster shipping via Postal Service or UPS is provided at the customer’s request.
Shipping charges: We do not require a minimum order amount, however, due to constantly rising costs,
effective January 5, 2009: Our shipping charge is $7.00, per order, for ALL orders weighing up to one
pound. For ALL orders weighing over one pound, we add actual shipping charges to your order. There
are three exceptions to this policy: (1) Some of the items in our catalog require additional pre-packaging
because they are extremely fragile. (2) In some cases an item is larger than normal carrier size for
standard packages. If an item requires an additional packaging and shipping charge, that charge is
indicated next to the catalog description for that particular item. (3) ALL orders shipped to countries
outside the United States please add 8 additional US dollars to your shipping charge for completion of all
of the paperwork associated with international shipments. We prefer not to ship C.O.D. If C.O.D. delivery
is necessary: A fee of $10.00 will be added to the regular shipping charges, to cover postal fees. We ship
C.O.D. within the United States only. As an alternative to C.O.D. we suggest that customers send us a
Money Order.
Upon receiving your order: We strongly recommend that you open your package(s) immediately to ensure
that each item has been shipped correctly, as per your order, and to ensure that your order has not been
damaged during shipping. If any item is damaged, please contact the carrier and file a claim with them.
Payment: We accept Visa, Master Card, Discover, Paypal, Business and Personal Checks,
(with sufficient funds and paid through a USA bank in United States dollars), Money Orders, C.O.Ds.
and of course Cash. We ship C.O.D. within the United States only.
Catalog prices: Our current prices will not increase unless, for reasons beyond our control, our “cost of
goods” prices increase. All prices subject to change without notice and we will do our best to keep our
current prices intact. Please note: We always confirm current prices with each customer and for each
order before we process the order.
Volume Discounts: Volume discounts are available to anyone as follows: Purchase $500.00 or more
deduct 5%; $1,000.00 or more deduct 10%; $1,500.00 or more deduct 15%; $3,000.00 or more
deduct 20%. Volume discounts do not apply to shipping & handling charges, items currently on sale,
original parts and items in the catalog that are marked NO DISCOUNT.
No hassle return Policy: If there is ever a problem with any item that you receive from us, please let us
know as soon as possible so we can correct the problem to your satisfaction. Returns are very rare at
A-1 Jukebox & Nostalgia; however if you ever have a need to return an item, please include a copy of the
original invoice with the return.
-3-
INDEX
MFGR. & MODEL # or ITEM
PAGE #
MFGR. & MODEL # or ITEM
7” 45 R.P.M. Records, (Our inventory consists
of 11,000 45 R.P.M. Records). For information
about 45s please see page #s….……... ……76
PAGE #
Seeburg Manuals & Parts, (Continued)
146 – 147 & 148 ………………………..14
M100A …………………………..…15 – 17
M100B & M100BL ………………. 17 – 20
M100C…………………………… . 21 – 24
HF100G & W100 ….…………… . 25 – 28
HF100R, 100 J & 100 JL ……… . 28 – 31
V 200 & VL 200 ………….….…… 31 – 35
KS 200 & KD 200 …………………35 – 38
L100 & 101, (L101) ……………… 38 – 41
161 ………………………………… 41 – 43
201 ………………………………… 43 – 45
220…………………………………. 45 – 47
222 ………………………………… 47 – 49
Q100, (AQ100)………. ..………… 49 – 51
Q160, (AQ160) ……………………51 – 53
AY100, Y100, AY160 & Y160…… 53 – 54
DS100 & DS160 …………………. 55 – 56
LPC1 & LPC480 . …………………56 – 57
PFEAIU “Electra” &
APFEAI “Fleetwood”…..…………. 58 – 59
SS160 “Stereo Showcase”….……59 – 60
LS1 “Spectra” & LS2 “Gem” ……..60 – 61
LS3 thru STD4 Grey & Black box ……..62
USC1 “Bandshell” …………………62 – 63
USC2 “Bandshell Firestar” ….…… 63 – 64
Speakers, & Accessories for SEEBURG ..…….66
Wallbox Parts for SEEBURG … 3W-1,
160, 200 & Consolette Parts ……. 66 – 67
Title Strips & Record Accessories . ……….. 76
Tools …..……………………………………… 77
Tubes (Electron) & Tube Sockets …….77 – 78
Volume Controls, (Potentiometers), are
listed under the Jukebox Models for
which they are available.
Wurlitzer Keyboard Button Sets ….………. 67
Miscellaneous Wurlitzer Parts . …. 67 – 68
Mounting Boards for Mechanisms ……. 69
Turntable Drive Belts, for Wurlitzer’s:
are listed under miscellaneous
Wurlitzer parts, page ……………... ……68
Cabinet Keys for Wurlitzer’s . …………. 69
AMi Manuals & Parts:
A …………………………………..……….. 5
B …………………………………………… 6
C ………………………………………. 6 – 7
D 40 & D 80…………………….….……… 7
E ………………………………………. 7 – 8
H & I ………………………………………... 8
Lyric & Continental 1 ………………………9
Continental 2 .. ……………………… 9 – 10
Ballasts, Starters & Sockets:
(For Fluorescent Lamps) ……………………. 73
Books, (History & Restoration) …………69 – 70
Bulbs, (Light Bulbs, Incandescent) …………. 70
Bulbs, (Miniature Bulbs) .…….……………… 70
Capacitor Kits, See: Model of Jukebox
Cartridges & Needles for all Jukeboxes 71 – 72
Fluorescent Lamps & Parts for ……………… 73
Foils, Embossed, (For Cabinet Interiors) ….. . 74
Fuses ……………………………………….. …74
Grill Cloths .……………….………….……… ..74
Hardware, For SEEBURG Jukeboxes,
(NUTS, BOLTS & SCREWS) ………………. 64
Keys, (Seeburg Cabinet Keys) ……………. 65
Keys, (Wurlitzer Cabinet Keys) ………….…69
Line Cords, (Power cords), Plugs & Outlets ..…74
Lubricants ………………………………………74
Needles, (Replacement Styli) …………. 71 – 72
Packard Pla-Mor Model 7 …… … ..…………10
Paint (Custom Colors for Seeburg,
Acrylic Enamel Spray cans) …….65 – 66
Polish for Plastics and Metals ………………. 75
Plugs & Sockets for Speakers, etc. ………… 75
Record Accessories ………………………….. 76
Rubber Gasket ……………………………. .. 76
Rock-Ola Manuals & Parts:
1422, 1426, 1428 & 1432 thru 1475 ….…. 11
1493 “Princess” ……………………… 11 – 12
435 “Princess Deluxe” ……………………12
480 – 488 ………………………………… 12
Seeburg Manuals & Parts:
Classic, Vogue & Cadet …………………13
Envoy ……….. …………………….. 13 – 14
Colonel, Major, & 7800 ………………… 14
8800 Super & 9800 Deluxe ……………. 14
We also stock original Jukebox parts.
If you need a part that is not listed in our
2010/2011 Catalog, please Call: 410-945-8900,
Email: [email protected] or Fax your
request for availability & pricing.
-4-
Please note: Because of unexpected increases in manufacturing costs, catalog prices are subject to
change and without notice. We always confirm current prices with each customer and for each order.
We appreciate your order.
A-1 Jukebox & Nostalgia, Inc.
Prices are Current as of November 1, 2010.
AMi
AMi A of 1946 – 1947 (40 Selections)
A-1 PART #
80-001 Service & parts manual for AMi Models A and B, 22 pages, order R-185
01-003 Plastics, for upper cabinet, pre-tested = perfect fit, (Out of stock until October
2011), (This set is not discountable), (Available in four piece sets only)
01-002 Fluted plastics, lower cabinet, pre-tested for perfect fit, (Out of stock until
October 2011), (This item is not discountable), (Available in pairs only)
66-001 Cloud-shaped pricing decals, water transfer to inside of glass, 5 to choose
from, Specify: 1/5¢ Special 6/25¢; 2/10¢ Special 6/25¢; 2/10¢ Special 5/25¢;
1/10¢ Special 3/25¢ or Special 1 play for 25¢, (large size: 5” x 4”), each
01-004 Instruction glass, printed, for front door, large, (18" W X 13 ¼” H)
01-005 Instruction glass, printed, for front door, small, (9 ¼“ W X 11 ¼” H)
01-006 Plastic instruction panel, printed, (this panel is used only if the front door
was constructed with rivets), Includes rivets, (18” W X 13 ½ “ H)
01-007 Mirror for back door, 3 color printed, (AMI GIVES YOU 40 SELECTIONS)
01-008 Mounting blocks for mirror, wooden, w/4 screws, sold in pairs only, per pair
85-014 Conversion Ring, blue, plastic, flexes to hold a 45 R.P.M. record, each
01-016 Reject button, chrome plated metal
85-001 Color sheets, lower, Stationary – no animation, (6 ½” W X 15” H), pair
85-002 Color sheets, lower, for original animation, (16” X 16”), pair
85-017 Motor 20 R.P.M., for left side animation, drive pinion not included, (1)
85-025 Motor 20 R.P.M., for right side animation, drive pinion not included, (1)
85-018 Drive Pinion, mounts on lower animation motor, turns color cylinder, ea.
01-009 Cash bag, (duck cloth, as original), hand made in the U.S.A.
01-010 Jewel set, (16 pieces of carved glass with layout diagram)
01-012 Jewel casting, aluminum, rough finish, (limited quantity)
01-013 Wood panel for mounting jewel casting, original shape, solid walnut
01-014 Bulb, Incandescent, 40 watt, 10 ½” clear glass, for behind jewels
01-018 Molding, for bottom of cabinet, brushed Stainless Steel, 2 pieces
designed to join in the middle of the cabinet, shaped as original,
screw holes have not been drilled, per two piece set
70-015 Fluorescent lamp 15 watt 18” T12 CW with colored sleeve & two sleeve
caps, (Specify: sleeve color yellow, red, blue or green), each
85-029 Colored sleeve, yellow, & two sleeve caps, for 18” T12 fluorescent lamp
85-032 Colored sleeve, red, & two sleeve caps, for 18” T12 fluorescent lamp
85-033 Colored sleeve, blue, & two sleeve caps, for 18” T12 fluorescent lamp
85-034 Colored sleeve, green, & two sleeve caps, for 18” T12 fluorescent lamp
70-016 Fluorescent lamp 14 watt 15" T12 cool white, (2 required), ea.
70-017 Fluorescent lamp 15 watt 18" T12 CW, (6 CW or daylight required), ea.
70-018 Fluorescent lamp 15 watt 18" T12, daylight, (6 daylight or CW required), ea.
71-001 Ballast 14 to 20 watt, for 1 lamp, new square style, clamped core, white, each
71-028 Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
-5-
$22.50
425.00
250.00
9.00
48.00
46.00
48.00
50.00
15.00
8.00
18.00
18.00
28.00
30.00
30.00
15.00
12.00
75.00
120.00
90.00
12.00
195.00
12.00
5.00
5.00
5.00
5.00
9.00
7.00
7.00
12.00
1.50
12.00
AMi B of 1948 – 1949 (40 Selections)
A-1 PART #
80-001
02-002
02-003
02-004
85-014
85-039
85-004
85-005
85-015
85-017
85-025
85-026
85-018
85-029
70-002
70-017
70-018
70-006
70-007
71-005
71-001
71-028
Service & parts manual for AMi Models A and B, 22 pages, order R-185
Vision panels with curved gold stripe, sold in pairs only, per pair
Fluted plastics, lower cabinet, sold in pairs only, per pair
Program and Instruction glass, 3 color printed, (10" W X 13 7/8” H)
Conversion Ring, blue, plastic, flexes to hold a 45 R.P.M. record, each
Color sheet, upper, original stripe pattern, (11” X 22 ½”), (1)
Color sheets, lower animation, original stripe pattern, (11” x 22 ½”), pair
Color sheets, original stripe pattern, (11” X 22 ½”), 1 upper & 2 lower, (Save 15%)
End caps for animation color sheets, stainless steel, each cap
Motor 20 R.P.M., for left side animation, drive pinion not included, (1)
Motor 20 R.P.M., for right side animation, drive pinion not included, (1)
Motor 20 R.P.M., for upper animation, drive pinion not included, (1)
Drive Pinion, mounts on lower animation motor, turns color cylinder, ea.
Colored sleeve, yellow, & two sleeve caps, for 18” T12 fluorescent lamp
Fluorescent lamp 8 watt 12” T5, cool white (program lamp)
Fluorescent lamp 15 watt 18" T12 CW, (2 CW or daylight required), ea.
Fluorescent lamp 15 watt 18" T12, daylight, (2 daylight or CW required), ea.
Fluorescent lamp 20 watt 24" T12, CW, (1 CW or daylight required), ea.
Fluorescent lamp 20 watt 24" T12, daylight, (1 daylight or CW required), ea.
Ballast 4 to 8 watt T5, for 1 lamp, new square style, clamped core, each
Ballast 14 to 20 watt, for 1 lamp, new square style, clamped core, white, each
Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
$22.50
150.00
240.00
48.00
8.00
14.00
28.00
35.50
7.00
30.00
30.00
30.00
15.00
5.00
7.00
7.00
7.00
7.00
7.00
10.00
12.00
1.50
12.00
AMi C of 1950 – 1951 (40 Selections)
A-1 PART #
80-002
03-002
03-001
03-004
03-003
03-005
66-001
03-008
03-007
03-006
85-014
03-010
85-006
85-040
85-007
85-015
85-017
85-025
85-018
70-017
70-018
Service & parts manual, AMi Model C, 76 pages, order R-216
Center cabinet panels, curved, clear plastic, pair
Center cabinet panel, curved, clear plastic, each
Lower cabinet panels, curved, white plastic, pair
Lower cabinet panel, curved, white plastic, each
Special! Purchase 2 Center clear & 2 Lower white,
(No additional discount at this Special price), 4 piece set
Cloud-shaped pricing decals, water transfer to inside of glass, 5 to choose
from, Specify: 1/5¢ Special 6/25¢; 2/10¢ Special 6/25¢; 2/10¢ Special 5/25¢;
1/10¢ Special 3/25¢ or Special 1 play for 25¢, (large size: 5” x 4”), each
Grill panel and first grill louver, large formed plastic
Grill louvers, original shape and color, 11 piece set
Grill louver, original shape and color, each
Conversion Ring, blue, plastic, flexes to hold a 45 R.P.M. record, each
Coins glass, 3 colors, one play 5¢, two plays 10¢, six plays Quarter
Color sheet, for mirror light box, (30” X 4 ½”), (1)
Color sheets, lower animation, match original stripe, (11 X 22 ½”), pair
Color sheets, 1 mirror light box & 2 lower animation, 3 pc. set, (Save 15%)
End caps for animation color sheets, stainless steel, each cap
Motor 20 R.P.M., for left side animation, drive pinion not included, (1)
Motor 20 R.P.M., for right side animation, drive pinion not included, (1)
Drive Pinion, mounts on lower animation motor, turns color cylinder, each
Fluorescent lamp 15 watt 18" T12 cool white
Fluorescent lamp 15 watt 18" T12, daylight
-6-
$35.00
75.00
42.00
95.00
52.00
160.00
9.00
40.00
135.00
14.00
8.00
15.00
18.00
28.00
39.00
7.00
30.00
30.00
15.00
7.00
7.00
AMi C of 1950 – 1951 (40 Selections) (Continued)
A-1 PART #
70-006
70-007
71-001
71-028
Fluorescent lamp 20 watt 24" T12, cool white
Fluorescent lamp 20 watt 24" T12, daylight
Ballast 14 to 20 watt, for 1 lamp, new square style, clamped core, white, each
Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
$7.00
7.00
12.00
1.50
12.00
AMi D 40 (40 Selections) and D 80 (80 Selections) of 1951-1952
A-1 PART #
80-003 Service, Parts & Trouble Shooting, AMi D-40, 88 pages, order R-270
80-004 Service, Parts & Trouble Shooting, AMi D-80, 94 pages, order R-264
04-001 Valance, upper cabinet, molded plastic, “Music For You By Ami”,
(This item is unavailable until October 2011), (add $20.00 for Packing,
Insurance & Shipping and an oversize box), (This item is not discountable)
04-003 Dome Decal (AMi 80 Selections)
66-001 Cloud-shaped pricing decals, water transfer to inside of glass, 5 to choose
from, Specify: 1/5¢ Special 6/25¢; 2/10¢ Special 6/25¢; 2/10¢ Special 5/25¢;
1/10¢ Special 3/25¢ or Special 1 play for 25¢, (large size: 5” x 4”), each
85-030 Drive belt for turntable, AMi # F-2143, (larger), for D 80, E 80 & E 120 only
85-031 Drive belt for turntable, AMi # F-2155, (smaller), for D 80, E 80 & E 120 only
85-014 Conversion Ring, blue, plastic, flexes to hold a 45 R.P.M. record, each
85-008 Color sheet, upper animation, original pattern – 20 stripes, (22” X 11”), (1)
85-009 Color sheets, for D 40, D 80, E 80 and E 120, lower animation,
matches original pattern, (11” X 16”), pair
85-010 Color sheets, animation, 1 upper & 2 lower, 3 piece set, (Save $5.00)
85-015 End caps for animation color sheets, stainless steel, each cap
85-016 End cap with rocker stud, for upper animation color sheet, (1)
85-026 Motor 20 R.P.M., for upper animation, rocker arm not included, (1)
85-017 Motor 20 R.P.M., for left side animation, drive pinion not included, (1)
85-025 Motor 20 R.P.M., for right side animation, drive pinion not included, (1)
85-018 Drive Pinion, mounts on lower animation motor, turns color cylinder, ea.
70-017 Fluorescent lamp 15 watt 18" T12 CW, (2 CW or daylight required), ea.
70-018 Fluorescent lamp 15 watt 18" T12, daylight, (2 daylight or CW required), ea.
70-006 Fluorescent lamp 20 watt 24" T12, CW, (1 CW or daylight required), ea.
70-007 Fluorescent lamp 20 watt 24" T12, daylight, (1 daylight or CW required, ea.
71-001 Ballast 14 to 20 watt, for 1 lamp, new square style, clamped core, white, each
71-028 Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
$35.00
35.00
275.00
14.00
9.00
6.00
6.00
8.00
15.00
24.00
34.00
7.00
10.00
30.00
30.00
30.00
15.00
7.00
7.00
7.00
7.00
12.00
1.50
12.00
AMi E Series of 1953 (40-80-120 Selections)
A-1 PART #
80-005
80-091
80-092
80-093
05-001
Service & parts manual, AMi E-40, E-80 & E-120, 90 pages, order R-160
Service & parts manual, AMi F-40, F-80 & F-120, 122 pages, order R-183
Quick reference guide & operators manual AMi F Series, 24 pgs., order R-302
AMi F Series, purchase R-183 and R-302, save $9.00, order R-183-A
Plastic front window, curved, printed, E-80 only, (27 7/8” W X 15 ¼“ H),
(add $20.00 for shipping an oversize box), (This item is not discountable)
(Parts for AMi E Series, Continued on the next page)
-7-
$37.00
40.00
17.00
48.00
110.00
AMi E Series of 1953 (Continued)
A-1 PART #
05-002 Side panel, clear plastic, E-80 only, each
66-001 Cloud-shaped pricing decals, water transfer to inside of glass, 5 to choose
from, Specify: 1/5¢ Special 6/25¢; 2/10¢ Special 6/25¢; 2/10¢ Special 5/25¢;
1/10¢ Special 3/25¢ or Special 1 play for 25¢, (large size: 5” x 4”), each
85-030 Drive belt for turntable, AMi # F-2143, (larger), for D 80, E 80 & E 120 only
85-031 Drive belt for turntable, AMi # F-2155, (smaller), for D 80, E 80 & E 120 only
85-011 Color sheet, upper animation, E-120, NEW pattern, Wider stripes,
(30” X 10”), can be used for E-80 if width of sheet is trimmed, (1)
85-009 Color sheets, for D 40, D 80, E 80 and E 120, lower animation,
matches original pattern, (11” X 16”), per pair
85-019 Color sheets, animation, E-80 & E-120, 1 upper & 2 lower,
(Save 13% off the individual piece price), 3 piece set
85-015 End caps for animation color sheets, stainless steel, each cap
85-016 End cap with rocker stud, for upper animation color sheet, (1)
85-026 Motor 20 R.P.M., for upper animation, rocker arm not included, each
85-017 Motor 20 R.P.M., for left side animation, drive pinion not included, (1)
85-025 Motor 20 R.P.M., for right side animation, drive pinion not included, (1)
85-018 Drive Pinion, mounts on lower animation motor, turns color cylinder, ea.
70-017 Fluorescent lamp 15 watt 18" T12 cool white
70-018 Fluorescent lamp 15 watt 18" T12, daylight
70-006 Fluorescent lamp 20 watt 24" T12, cool white
70-007 Fluorescent lamp 20 watt 24" T12, daylight
71-001 Ballast 14 to 20 watt, for 1 lamp, new square style, clamped core, white, each
71-028 Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
$18.00
9.00
6.00
6.00
22.00
24.00
40.00
7.00
10.00
30.00
30.00
30.00
15.00
7.00
7.00
7.00
7.00
12.00
1.50
12.00
AMi H of 1957 and I of 1958 (100-120-200 Selections)
A-1 PART #
80-006
80-007
80-008
80-009
80-010
80-011
80-094
76-023
85-012
70-006
70-007
71-001
71-028
Service manual AMi Model H series, 118 pages, order R-396
Service manual AMi H & i credit/selection system, 18 pgs., order R-397
AMi Model H, Purchase R-396 & R-397, save $5.00, order R-397-A
Service manual AMi Model i series, 140 pages, order R-528
Parts catalog AMi Model i series, 100 pages, order R-529
AMi Model i, purchase R-528 and R-529, save $10.00, order R-528A
Service bulletins for AMi Models: G, H & i, 65 pages, order R-16
Key for cabinet for Ami Models: G, H & i, key # R1303
AMi Model H Color Sheet, original pattern, gives color to front grill (26” X 6”)
Fluorescent lamp 20 watt 24" T12, cool white
Fluorescent lamp 20 watt 24" T12, daylight
Ballast 14 to 20 watt, for 1 lamp, new square style, clamped core, white, each
Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
(Parts for AMi Lyric & Continental 1 are listed on the next page)
-8-
$40.00
15.00
50.00
42.00
38.00
70.00
28.00
7.00
16.00
7.00
7.00
12.00
1.50
12.00
AMi LYRIC of 1961 50 Records (100 Selections)
and CONTINENTAL 1 of 1961 100 Records (200 Selections)
A-1 PART #
80-012 Service Manual for AMi Continental 2, (use this manual for
AMi Lyric & AMi Continental I), 126 pages, order R-375
80-013 Cabinet & Component parts, for AMi Lyric & Cont. I, 33 pages, order R-63
80-014 Service bulletins, remote controls, wall boxes & accessories,
for AMi K, Lyric, Continental I and 2, 60 pages, order manual # R-531
85-035 Record changer trim, (mech. shroud), & plug-button, (for Cont. I & 2 only)
07-003 Credit glass, original aqua color, round, glass, not plastic
07-008 Price card, aqua background, standard plays 5¢ 1, 10¢ 2 & quarter 5
07-009 Price card, aqua background, dime/two nickels 1, quarter 3 & half dollar 6
07-010 Price card, aqua background, dime/two nickels 1, quarter 4 & half dollar 8
07-011 Price card, aqua background, standard plays: dime/two nickels 1, quarter 3
& half dollar 7 and extended plays: fifteen cents 1, quarter 2 & half dollar 5
07-005 Program title headings, aqua: hit tunes, rock and roll, oldies, etc., 24 pc. set
75-003 Pickering magnetic Cartridge, model NP/AC, excellent replacement
07-002 Letters/numbers glass for selection buttons, 3 pc. set, (original aqua color)
07-001 Diffuser above grill, original shape, (multicolored for Cont. I & Lyric Models)
76-022 Key for cabinet, arch & back door, (not cash door), C440A
85-020 Cash door, superior Burch covered plywood, with metal reinforcement plates,
for AMi models J, K, Continental 1, Continental 2, Lyric, L, M and N
85-021 Access door, (covers coin acceptor), superior Burch covered plywood, with
metal reinforcement plates, AMi Models: J, K, Cont. 1 & 2, Lyric, L, M & N
76-065 Lock, 7/8” quality lock, & 2 keys for AMi, Reproduction - wooden cash door
76-070 Lock, 7/8” quality lock, hardware, & 2 keys for Original AMi metal cash door
72-004 Bulb, miniature #47 (pilot bulb and credit bulbs), each
72-005 Bulb, miniature #1847 (manuals call for this longer lasting bulb), each
70-002 Fluorescent lamp 8 Watt 12" T5 cool white, illuminates title strips, (2), each
70-006 Fluorescent lamp 20 watt 24" T12, cool white, for front, (1)
70-007 Fluorescent lamp 20 watt 24" T12, daylight, (optional color), for front
71-005 Ballast 4 to 8 watt T5, for 1 lamp, new square style, clamped core, each
71-001 Ballast 14 to 20 watt, for 1 lamp, new square style, clamped core, white, each
71-028 Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
$41.50
24.50
27.00
80.00
15.00
5.00
5.00
5.00
5.00
15.00
40.00
38.00
30.00
7.00
18.00
19.50
10.00
10.00
1.00
1.50
7.00
7.00
7.00
10.00
12.00
1.50
12.00
AMi CONTINENTAL 2 of 1962 (100 and 200 Selections)
A-1 PART #
80-012
80-016
80-017
80-014
85-035
08-005
08-020
08-007
08-009
08-027
08-028
Service manual, AMi Cont. 2, 100 & 200 Models, 126 pages, order R-375
Parts catalog, AMi Continental 2, 92 pages, order R-373
AMi Continental 2, purchase R-375 and R-373, save $9.00, order R-375A
Service bulletins, remote controls, wall boxes & accessories,
for AMi K, Lyric, Continental I and 2, 60 pages, order manual # R-531
Record changer trim, (mech. shroud), & plug-button, (for Cont. I & 2 only)
STEREO ROUND printed plastics, (for each side of title case), pair
STEREO ROUND printed plastic, (for either side of title case), each
(08-005 & 08-020 will not be available until October 2011)
Credit glass, original red color, round, glass, not plastic
Price card, (as original), red print on white background
Price card, red background, standard plays 5¢ 1, 10¢ 2 & quarter 5
Price card, red background, dime/two nickels 1, quarter 3 & half dollar 6
-9-
$41.50
32.50
65.00
27.00
80.00
50.00
25.00
15.00
7.00
5.00
5.00
AMi CONTINENTAL 2 of 1962 (Continued)
A-1 PART #
08-029 Price card, red background, dime/two nickels 1, quarter 4 & half dollar 8
08-030 Price card, red background, standard plays: dime/two nickels 1, quarter 3
& half dollar 7 and extended plays: fifteen cents 1, quarter 2 & half dollar 5
08-010 33/45 Automix card, (as original), red & black print on white background
08-011 Star & dots card, replaces automix card, red & black print on white background
08-013 Program title headings, red: hit tunes, rock and roll, oldies, etc., 24 pc. set
75-003 Pickering magnetic Cartridge, model NP/AC, excellent replacement
08-006 Letters/numbers glass for selection buttons, 3 pc. set, (original red color)
08-001 Front Glass, (Continental 2, printed in script as original)
08-002 Front multi-colored red/orange printed plastic, (w/ 3 holes for AMi logo only)
08-003 Front multi-colored red/orange printed plastic, (with 3 holes for AMi logo
and 24 additional holes) for “STEREO – ROUND”
08-025 Logo & STEREO ROUND Letters for front printed plastic
08-004 Diffuser above grill, original shape and colors, (red & clear)
76-022 Key for cabinet, arch & back door, (not cash door), C440A
85-020 Cash door, superior Burch covered plywood, with metal reinforcement plates,
for AMi models J, K, Continental 1, Continental 2, Lyric, L, M and N
85-021 Access door, (covers coin acceptor), superior Burch covered plywood, with
metal reinforcement plates, AMi Models: J, K, Cont. 1 & 2, Lyric, L, M & N
76-065 Lock, 7/8” quality lock, & 2 keys for AMi, Reproduction - wooden cash door
76-070 Lock, 7/8” quality lock, hardware, & 2 keys for Original AMi metal cash door
72-004 Bulb, miniature #47 (pilot bulb and credit bulbs), each
72-005 Bulb, miniature #1847 (manuals call for this longer lasting bulb), each
70-001 Fluorescent lamp 6 Watt 9" T5 cool white, lights record magazine, (2), each
70-002 Fluorescent lamp 8 Watt 12" T5 cool white, lights title strips, (2), each
70-006 Fluorescent lamp 20 watt 24" T12, cool white, lights front glass, (1)
70-007 Fluorescent lamp 20 watt 24" T12, daylight, (optional color), for front
71-005 Ballast 4 to 8 watt T5, for 1 lamp, new square style, clamped core, each
71-001 Ballast 14 to 20 watt, for 1 lamp, new square style, clamped core, white, each
71-028 Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
$5.00
5.00
7.00
7.00
15.00
40.00
38.00
65.00
58.00
62.00
45.00
20.00
7.00
18.00
19.50
10.00
10.00
1.00
1.50
7.00
7.00
7.00
7.00
10.00
12.00
1.50
12.00
FOR AMi & ROWE – AMi JUKEBOXES
WE STOCK: SERVICE MANUALS, TROUBLE SHOOTING GUIDES,
PARTS LISTS, MINI BULBS, CARTRIDGES, STYLI – (NEEDLES),
FLUORESCENT LAMPS, AND KEYS, (FOR ORIGINAL CABINET LOCKS),
FOR MOST MODELS
Please Call or Email for details and pricing.
PACKARD
PACKARD Pla-Mor Model 7 of 1946 – 1949 (24 Selections)
A-1 PART #
80-096 Installation & service manual, Pla-Mor Model 7, 30 pages, order R-164
80-097 Sale ads for Pla-Mor, Manhattan & remote equipment and
articles about the Packard Corporation, 48 pages, order R-242
80-098 Service manual for wallbox for Pla-Mor & Manhattan, 8 pages, order R-90
09-001 Plastic curtains for mechanism area, for “Pla-Mor” Model 7 only,
original printed pattern, (original plastic curtains are usually
discolored or missing), (This set is not discountable), 4 piece set
- 10 -
$25.00
27.00
14.00
130.00
ROCK-OLA
ROCK-OLA 1422 of 1946, 1426 of 1947 and 1428 of 1948 – 1949
(20 Selections)
A-1 PART #
80-018
80-019
80-020
10-001
72-014
Service & parts manual for 1422 through 1428, 31 pages, order R-229
Trouble shooting guide for 1422 through 1428, 32 pages, order R-214
Rock-Ola 1422 thru 1428, purchase R-229 & R-214, save $6.00, order R-229A
1428 Center amber plastic for front door, resin molded, exact reproduction
Bulb, miniature #313, 28 volt, Use bulb # 1819 (A-1 Part # 72-017),
for Rock-Ola 1422, 1426 and 1428, (Thank You lamp), each
72-017 Bulb, miniature #1819, 28 volt, (replaces bulb #313), each
$27.00
27.00
48.00
175.00
2.00
2.00
ROCK-OLA 1432 THROUGH 1475
A-1 PART #
80-140
80-141
80-142
80-143
80-144
80-145
80-146
80-135
80-136
80-137
80-147
80-148
80-149
80-150
80-151
80-152
77-030
77-031
68-028
68-029
68-031
91-001
91-002
55-009
Service and parts manual, Rock-Ola 1432, 80 pages, order R-318
Service and parts manual, Rock-Ola 1434, 65 pages, order R-319
Service and parts manual, Rock-Ola 1436, 45 pages, order R-194
Service and parts manual, Rock-Ola 1436A, 43 pages, order R-215
Service and parts manual, Rock-Ola 1438, 38 pages, order R-169
Service and parts manual, Rock-Ola 1442, 40 pages, order R-315
Service and parts manual, Rock-Ola 1446, 40 pages, order R-312
Service & parts manual, Rock-Ola 1448, 48 pages, order R-171
Service & parts manual, Rock-Ola 1452, 40 pages, order R-279
Service & parts manual, Rock-Ola 1454, 46 pages, order R-280
Service manual, Rock-Ola 1455 Standard & Deluxe, 40 pgs., order R-241
Parts manual, Rock-Ola 1455 Standard & Deluxe, 35 pgs., order R-525
Service & Parts, 2 manuals, Rock-Ola 1455 Standard & Deluxe, order R-241A
Service and parts manual, Rock-Ola 1468, 66 pages, order R-322
Manual, defines Stereophonic sound, has schematics & parts list,
Rock-Ola’s: 1460, 1468 and 1475-ST, 20 pgs., order R-316
Service and parts manual, Rock-Ola 1475, 64 pages, order R-174
Grill glass, Waffle pattern, (all sharp edges have been sanded for safety),
(Models 1448 & 1452 require 4 pcs.), (Model 1454 requires 2 pcs.),
(add $15.00 for special packaging and shipping), 4 piece set
Grill glass, Waffle, single panel, (all sharp edges have been sanded),
(Models 1448 & 1452 require 4 pcs.), (Model 1454 requires 2 pcs.), each
(Please note: 77-030 & 77-031 will not be available until October 2011)
Grill frame, front piece, (for waffle glass), polished stainless steel, each
Grill frame, rear piece, (for waffle glass), polished stainless steel, each
Grill frames, front & rear, (for waffle glass), polished stainless, 8 piece set
Volume control pot. for Rock-Ola Models 1446 through 1475 (mono. only)
Volume control pot., (Stereo), Models 1460 through 437 & some Seeburgs
Motor Brush for Gripper & Magazine motors, Rock-Ola # 31493,
for Rock-Ola Models: 1468 through 476, (2 required), each
$38.50
36.00
35.50
35.50
35.50
35.50
35.50
35.50
35.50
35.50
35.50
34.50
58.00
36.00
22.00
36.00
150.00
40.00
10.00
10.00
70.00
30.00
30.00
10.00
ROCK-OLA 1493 “PRINCESS” of 1962 50 Records (100 Selections)
A-1 PART #
80-021 Service & parts manual, Rock-Ola 1493, 80 pages, order R-269
11-002 Rear backdrop curtain, for inside cabinet, behind mechanism,
original pattern – white with purple stripe
11-001 Coin PRICES glass, HALF DOLLAR 7, QUARTER 3, DIME OR 2 NICKELS 1 PLAY
55-002 Grommets for turntable motor for all 45 R.P.M. Rock-Ola's, 3 required, each
55-009 Motor Brush for Gripper & Magazine motors, Rock-Ola # 31493, each
- 11 -
$37.00
25.00
9.00
1.00
10.00
ROCK-OLA 1493 “PRINCESS” of 1962 (Continued)
A-1 PART #
11-003
91-002
70-017
70-004
70-018
70-005
70-006
70-007
71-001
71-028
Grill medallion plastic, part # 35704, Crown and R logo, (as original)
Volume control pot., (Stereo), Models 1460 through 437 & some Seeburgs
Fluorescent lamp 15 watt 18" T12 cool white, lights crown and logo, (1)
Fluorescent lamp, 15 watt 18" T8, cool white, optional size, replaces T12
Fluorescent lamp 15 watt 18" T12, daylight, optional color
Fluorescent lamp, 15 watt 18" T8, daylight, optional size and color
Fluorescent lamp, 20 watt 24" T12 cool white, upper cabinet, (1)
Fluorescent lamp, 20 watt 24" T12 daylight, optional color
Ballast 14 to 20 watt, for 1 lamp, new square style, clamped core, white, each
Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
$60.00
30.00
7.00
7.00
7.00
7.00
7.00
7.00
12.00
1.50
12.00
ROCK-OLA 435 “Princess Deluxe” of 1967 – 68
50 Records (100 Selections)
A-1 PART #
80-099
80-101
80-102
40-001
55-002
55-009
91-002
70-019
71-006
71-035
Service manual, Rock-Ola 435, 56 pages, order R-415
Parts manual, Rock-Ola 435, 50 pages, order R-485
Rock-Ola 435, Purchase R-415 and R-485, save $7.00, order R-415A
Front door glass, Princess Deluxe, printed, (as original), not discountable
Grommets for turntable motor for all 45 R.P.M. Rock-Ola's, 3 required, each
Motor Brush for Gripper & Magazine motors, Rock-Ola # 31493, each
Volume control pot., (Stereo), Models 1460 through 437 & some Seeburgs
Fluorescent lamp 25 watt 30” T12 cool white, recommended color
Ballast, 25 watt, for 1 lamp, new style, (clamped core), made in the U.S.A.
Ballast, 25 watt, for 1 lamp, original style case & Black color, (Now thermally
protected), made in the U.S.A., includes 2 rubber grommets for mounting
71-028 Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
$35.00
28.00
56.00
65.00
1.00
10.00
30.00
10.00
12.00
20.00
1.50
12.00
ROCK-OLA 480 – 488 of 1979 – 1982 80 Records (160 Selections)
A-1 PART #
80-110
80-111
41-001
55-002
72-007
76-075
71-016
Service manual, Rock-Ola 480 “Techna”, 66 pages, order R-42
Service manual, Rock-Ola 488 “Vista”, 66 pages, order R-17
Instruction glass for 480, 484, 488; add coins, plays, record playing
Grommets for turntable motor for all 45 R.P.M. Rock-Ola's, 3 required, each
Bulb, miniature #53, 14.4 volt, (n.o.s., Westinghouse), (10% discount for 10 +), ea.
Key for cabinet, Rock-Ola models: 461 through 498, # P600, each
Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
FOR ROCK-OLA JUKEBOXES
WE STOCK: SERVICE MANUALS, TROUBLE SHOOTING GUIDES,
PARTS LISTS, MINI BULBS, CARTRIDGES, STYLI – (NEEDLES),
FLUORESCENT LAMPS, AND KEYS, (FOR ORIGINAL CABINET LOCKS),
FOR MOST MODELS
Please Call or Email for details and pricing.
- 12 -
$36.00
36.00
20.00
1.00
1.00
7.00
12.00
SEEBURG
SEEBURG CLASSIC of 1939 (20 Selections)
A-1 PART #
80-106 Schematic diagrams for all 20-selection Seeburg Models from
1938-1949, 95 pages, order R-381
80-103 Service manual for Classic, Vogue, Mayfair, Plaza & Casino,
58 pages, order R-309
80-104 Operate. maintain./corrective measures: Classic & Vogue, 16 pgs., order R-86
80-105 Purchase R-309, Service manual & R-86, Operation manual for Classic,
Vogue, Mayfair, Plaza & Casino, save $4.00, order R-309A
12-003 Upper cabinet plastics, red, for Seeburg Classic only,
3 lid pieces and 2 side pieces, (5-piece set)
12-004 Upper cabinet plastics, green for Seeburg Classic only,
3 lid pieces and 2 side pieces, (5-piece set)
12-002 Pilaster plastics, Red, for Seeburg Classic only, pair
73-021 Printed plastic set for keyboard area: SEEBURG SYMPHONOLA;
RECORD PLAYING; PRICING CARD - 5 PLAYS 25¢, etc.; vertical numbers 1 thru 20
and PRESS DOWN LEVERS, etc. with horizontal numbers 1 thru 20, 5 pieces
73-020 Plastic panels for front door, original, printed wave pattern, 3 colors, pair
$36.00
30.00
16.00
42.00
135.00
135.00
140.00
35.00
45.00
SEEBURG VOGUE of 1939 (20 Selections)
A-1 PART #
80-106 Schematic diagrams for all 20-selection Seeburg Models from
1938-1949, 95 pages, order R-381
80-103 Service manual for Vogue, Classic, Mayfair, Plaza & Casino,
58 pages, order R-309
80-104 Operate. maintain./corrective measures: Classic & Vogue, 16 pgs., order R-86
80-105 Purchase R-309, Service manual & R-86, Operation manual for Classic,
Vogue, Mayfair, Plaza & Casino, save $4.00, order R-309A
73-021 Printed plastic set for keyboard area: SEEBURG SYMPHONOLA;
RECORD PLAYING; PRICING CARD - 5 PLAYS 25¢, etc.; vertical numbers 1 thru 20
and PRESS DOWN LEVERS, etc. with horizontal numbers 1 thru 20, 5 pieces
73-020 Plastic panels for front door, original, printed wave pattern, 3 colors, pair
$36.00
30.00
16.00
42.00
35.00
45.00
SEEBURG CADET of 1940 (20 Selections)
A-1 PART #
80-106 Schematic diagrams for all 20-selection Seeburg Models from
1938-1949, 95 pages, order R-381
80-107 Service and parts manual for Cadet, Concert Master &
Commander, 132 pages, order R-276
80-108 Operation and maintenance manual for Cadet & Commander,
16 pages, order R-87
73-021 Printed plastic set for keyboard area: SEEBURG SYMPHONOLA;
RECORD PLAYING; PRICING CARD - 5 PLAYS 25¢, etc.; vertical numbers 1 thru 20
and PRESS DOWN LEVERS, etc. with horizontal numbers 1 thru 20, 5 pieces
76-001 Volume control key for original pots., (Seeburg amps. thru SHFA2 & all Wurlitzer’s)
$36.00
40.00
16.00
35.00
3.00
SEEBURG ENVOY of 1940 (20 Selections)
A-1 PART #
80-106 Schematic diagrams for all 20-selection Seeburg Models from
1938-1949, 95 pages, order R-381
80-112 Operation and maintenance manual for Envoy, Concert Master,
Colonel & Major, 16 pages, order R-88
- 13 -
$36.00
16.00
SEEBURG ENVOY of 1940 (Continued)
A-1 PART #
14-001 Cabinet lid plastics, Specify: blue, red, green or yellow, 3-piece set
14-002 Pilaster plastics, Red, for Seeburg Envoy only, pair
73-022 Printed plastic set for keyboard area: SEEBURG SELECTRIC SYMPHONOLA,
RECORD PLAYING, PRICING CARD 5 PLAYS 25¢, etc. & DEPOSIT COINS, 4 pcs.
14-003 Upper back door, (add $30.00 for packaging & shipping an oversize box)
14-004 Lower back door, (add $30.00 for packaging & shipping an oversize box)
76-001 Volume control key for original pots., (Seeburg amps. thru SHFA2 & all Wurlitzer’s)
$65.00
140.00
35.00
80.00
70.00
3.00
SEEBURG COLONEL & MAJOR of 1940
and 7800 of 1941 (20 Selections)
A-1 PART #
80-106 Schematic diagrams for all 20-selection Seeburg Models from
1938-1949, 95 pages, order R-381
80-112 Operation and maintenance manual for Colonel, Major,
Envoy & Concert Master, 16 pages, order R-88
80-114 Service and parts manual for 7800 “Standard”, 7850,
8800 “Super” & 9800 “Deluxe”, 90 pages, order R-494
73-022 Printed plastic set for keyboard area: SEEBURG SELECTRIC SYMPHONOLA,
RECORD PLAYING, PRICING CARD 5 PLAYS 25¢, etc. & DEPOSIT COINS, 4 pcs.
76-001 Volume control key for original pots., (Seeburg amps. thru SHFA2 & all Wurlitzer’s)
$36.00
16.00
35.00
35.00
3.00
SEEBURG 8800 SUPER and 9800 DELUXE of 1941 (20 Selections)
A-1 PART #
80-106 Schematic diagrams for all 20-selection Seeburg Models from
1938-1949, 95 pages, order R-381
80-114 Service and parts manual for Seeburg 8800 “Super” & 9800 “Deluxe”,
7800 “Standard” & 7850, 90 pages, order R-494
73-023 Printed plastic set: MAKE SELECTION / SELECTION PLAYING and
DEPOSIT COINS BEFORE MAKING SELECTIONS – 1 PLAY 5¢, etc., 2 pieces
76-001 Volume control key for original pots., (Seeburg amps. thru SHFA2 & all Wurlitzer’s)
$36.00
35.00
24.00
3.00
SEEBURG 146, 147 and 148 of 1946, 1947 and 1948 (20 Selections)
A-1 PART #
80-131
80-132
80-133
38-001
65-002
91-003
76-001
72-006
72-011
76-002
76-003
Service & parts manual, Seeburg 146, 147 & 148, 320 pgs., order R-265
Trouble Shooting guide, Seeburg 146, 147 & 148, 38 pgs., order R-440
146, 147 & 148, Purchase R-265 & R-440, save $10.00, order R-265A
Mirrors, blue, 270 One-inch squares, for front door
Grill cloth, Specify: gold, red or silver, other colors are listed
on page 74 under GRILL CLOTH, cloth size 30” X 40”, each
Volume control pot. for Models 146, 147, 148, A, B/BL, C, G, W & R
Volume control key for original pots., (Seeburg amps. thru SHFA2 & all Wurlitzer’s)
Bulb, miniature #51, 7.5 volt, Seeburg 146/147/148 selection dial &
Seeburg wallboxes (new original Westinghouse, best quality), each
Bulb, miniature #81, Seeburg 146/147/148 behind plastics, each
Key, New original stock key for Seeburg 146, 147, 148: Lid
L7380
Key, New original stock key for Seeburg 146, 147, 148: Door
L7325
(Seeburg Parts are continued on the next page)
- 14 -
$58.00
26.00
74.00
100.00
16.00
30.00
3.00
1.00
2.00
10.00
10.00
SEEBURG PROGRAM TITLE HEADINGS For The Following Seeburg
Models: M100A, M100B, M100BL, M100C, HF100G, W100, HF100R,
100J, 100JL, L100, 101, 161, 201, 220, 222, Q100 and Q160
Note: Seeburg program title heading-sets do not always contain the same
exact variety of headings. Popular headings are duplicated in all sets.
Sets contain: Hit Tunes, Rock & Roll and Old Favorites. Some sets contain:
Rhythm and Blues, Hillbilly, All Time Favorites and Jazz. Some sets contain:
Classics and Varieties, Country and Western and Christmas.
73-070
73-071
73-072
73-073
73-074
73-075
Seeburg Title headings for program holders, Red, 11 or 12 pieces
Seeburg Title headings for program holders, Maroon red, 11 or 12 pieces
Seeburg Title headings for program holders, Aqua, 11 or 12 pieces
Seeburg Title headings for program holders, Blue, 11 or 12 pieces
Seeburg Title headings for program holders, Green, 11 or 12 pieces
Seeburg Title headings for program holders, Black, 11 or 12 pieces
$10.00
10.00
10.00
10.00
10.00
10.00
Add color to the Program Title Strips and inside of your 1950s & 1960s
Seeburg Models M100A through LPC480. We stock Colored sleeves
that slip over the fluorescent lamps in your jukebox. To create a Rainbow
effect, choose from the following colors:
70-050 Colored sleeve for T12 fluorescent lamp, (cut to your specified length),
Specify: sleeve color: red, blue, green, yellow or pink, per foot
$1.75
70-055 Colored sleeve for T8 fluorescent lamp, (cut to your specified length),
Specify: sleeve color: red, blue, green, yellow, purple or pink, per foot
1.75
SEEBURG M100A of 1948 – 51 50 Records (100 Selections)
A-1 PART #
80-022 Service & parts manual, Seeburg M100A, 160 pages, order R-190
66-003 Decal, water transfer, apply to inside of glass dome facing out,
original wording, colors and font, “Seeburg Select-o-Matic 100”
66-001 Cloud-shaped pricing decals, water transfer to inside of glass, 5 to choose
from, Specify: 1/5¢ Special 6/25¢; 2/10¢ Special 6/25¢; 2/10¢ Special 5/25¢;
1/10¢ Special 3/25¢ or Special 1 play for 25¢, (large size: 5” x 4”), each
16-001 Side glass, for left or right side of dome, each
16-008 Insert for mechanism cover "100 Select-o-Matic Mechanism", Model M100A only
16-004 Program glass, 36” X 6 ¾”, (unprinted, as original), Model M100A only
16-005 Retainer, (frame), for program glass, Aluminum, 4 pc. set
68-070 Screw kit, stainless, for program-glass retainer & electrical selector, Phillips
head screws, 25 pcs, (13 wood & 12 metal screws, 1 extra of all 4 sizes included)
77-002 Instruction glass, Maroon, (Original Factory Color), Choose either Maroon
or Red, “PRESS ONE LETTER & MAKE SELECTIONS”, 2 piece set
77-060 Instruction glass, Red, (We have had many requests for this color),
“PRESS ONE LETTER & MAKE SELECTIONS”, 2 piece set
16-007 Coin instruction glass (6 plays 25¢, 2 for 10¢, 1 for 5¢)
68-012 Speed washers, hold instruction glass in place, 10 pieces
77-003 Diffuser glass for Electrical Selector, white with red stripes
77-035 Select glass, green, Models M100A, B, BL and C
77-036 Select glass, blue, Models M100A, B, BL and C
78-005 Latch bar solenoid for Electrical Selector, all metal frame, as original
78-020 Free play adapter, plugs in to existing credit unit, has switch for free play
or coin operation, eliminates latch bar solenoid burn-out, for Seeburg
Models: A, B, BL, C, G, W, R, J and JL, (This item is not discountable)
68-014 Coin reject plunger, (button), plated, with scavenger wire, (Models A, B & C)
- 15 -
$44.50
10.00
9.00
20.00
10.00
25.00
140.00
5.00
16.00
16.00
12.00
3.50
10.00
6.50
6.50
60.00
68.95
25.00
SEEBURG M100A of 1948 – 51 (Continued)
A-1 PART #
Specify #
68-007
83-003
84-015
16-006
16-002
65-008
65-009
65-011
65-012
16-009
86-004
86-005
16-003
65-002
65-018
16-010
68-001
76-004
67-004
67-007
76-050
81-001
68-003
68-002
68-026
66-002
66-005
92-037
92-050
92-015
92-025
37-009
91-003
76-001
Title headings for Seeburg program holders, Specify: a color and the
A-1 part # from the list at the top of page 15, (11 or 12 piece assortment)
Speed washers, round, hold letter/number strips & title headings to program
title holders. Also hold: 2 pc. Inst. glass; SELECT glass & COINS glass, 55 pieces
Brushes, stylus cleaning, for stripper arms, pair
Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
Mirror for left and right end of mechanism (2), each
Frosted diffuser glass, 32 ¾” X 8 ¼”, for behind program title board
Foil, embossed, gold, ¼” diamonds, for cabinet interior, 18" X 72" roll,
cloth backed, use spray adhesive for installation, per roll
Foil, embossed, gold, ¼” squares, for cabinet interior, 18" X 72" roll,
cloth backed, use spray adhesive for installation, per roll
Foil, embossed, silver, ¼” diamonds, for cabinet interior, 18” X 72” roll,
cloth backed, use spray adhesive for installation, per roll
Foil, embossed, silver, ¼” squares, for cabinet interior, 18” X 72” roll,
cloth backed, use spray adhesive for installation, per roll
Color sheet for animation cradle tray, Model M100A only
Motor, 10 R.P.M. for animation tray, with threaded shaft, 100% U.S.A. made
Mounting bracket, metal, for animation motor, Models M100A, B & BL
Glass above grill w/printed silver stripe, 30 ½” X 6 7/8”,
Grill cloth, Specify: gold, red or silver, other colors are listed
on page 74 under GRILL CLOTH, cloth size 30” X 40”, each
Grill cloth: Burlap, Available colors, Specify: red, black, gray or medium
blue, can be used on many 50s & 60s models, cloth size 30” x 40”, each
Grill bars, mirror polished stainless steel, radius bend as original, 21 pc. set
Screws for grill bars, stainless steel, (90 pcs.)
Key for cabinet sides and back door, (not cash door), G219
Cash bag, (duck cloth, as original, hand made in the U.S.A.)
Cash door, superior grade birch covered plywood, with backup plates, (for
use with no metal frame around opening, Models A, B/BL and some C)
Lock, 1 1/8” quality lock, & 2 keys for Reproduction - wooden cash door
I.D. plate, Model A, (as original), no serial number, for back of cabinet
Hook latches & 4 screws for inside of upper back door, A, B/BL, C, G/W, pr.
Safety chain for Lower back door, w/chain cover, mounting screw & key clip
Screws, hold Amp. & Receiver on lower back door, (4) 1”, (4) ½”, 65¢ ea. or 8 pcs.
Decals, water transfer, for lower back door, (On/Off & Vol. Control), 2 pc. set
Decals, Vinyl, peel & stick, for lower back door, (On/Off & Vol. Control), 2 pc. set
Capacitor kits for Amplifiers used in Seeburg Models: A, B, C, G & W,
Specify: Amplifier # MRA1-L6 through MRA4-L6, includes:
Schematics and replacement values reference sheet, each kit
Capacitor kit for WSR3, Selection Receiver, includes run condenser for
mechanism motor, schematics and replacement values reference sheet,
(does not include the capacitor for the Stepper that operates wallboxes)
Capacitor, (run condenser), for mechanism motor, original style/metal can,
for M100A thru STD4, not SX100, for all USA motors, not for Nidec motors
Capacitor for Stepper, operates wallboxes in Seeburgs: M100A thru LPC480
Fuse, 3 amp or 3 2/10 amp Fustat, large screw in type, for Seeburg: M100A
thru VL200 Selection Receivers, (these are for the operation of wallboxes)
Volume control pot. for Models 146, 147, 148, A, B/BL, C, G, W & R
Volume control key for original pots., (Seeburg amps. thru SHFA2 & all Wurlitzer’s)
- 16 -
$10.00
8.00
12.00
25.00
12.00
25.00
40.00
40.00
40.00
40.00
22.50
40.00
8.00
25.00
16.00
16.00
140.00
6.00
7.00
12.00
18.00
10.00
15.00
10.00
10.00
5.00
10.00
8.00
65.00
57.50
30.00
12.00
8.00
30.00
3.00
SEEBURG M100A of 1948 – 51 (Continued)
A-1 PART #
72-004
72-006
72-011
70-013
70-012
71-008
71-010
71-016
71-030
68-004
Bulb, miniature #47 (behind select glass) (2), each
Bulb, miniature #51 (selection playing indicator) (2), each
Bulb, miniature #81 (behind Mech cover insert)
Fluorescent lamp 30 watt 36" T8, daylight, recommended color (1)
Fluorescent lamp 30 watt 36" T8, cool white, optional color
Ballast 30 to 40 watt, for 1 lamp, (Thermally protected), made in the U.S.A.
Starter with condenser, FS-4, 30 to 40 watt, made in the U.S.A., each
Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
Outlet, 3-wire grounded duplex receptacle, (The Receiver plugs into this)
Caster sockets, use with original Seeburg metal casters or our 2 ½” hard
rubber replacement casters, (made by original supplier to Seeburg), each
68-005 Casters 2 ½” hard rubber, (made by original supplier to Seeburg), each
$1.00
1.00
2.00
10.00
10.00
30.00
1.50
12.00
8.00
3.00
7.00
SEEBURG M100B of 1950 – 1951 and M100BL of 1951 – 1952
50 Records (100 Selections)
A-1 PART #
80-023 Service & parts manual, Seeburg M100B & BL, 221 pages, order R-258
17-001 Glass dome, with printed logo, (add $40 for packaging & shipping)
66-003 Decal, water transfer, apply to inside of glass dome facing out,
original wording, colors and font, “Seeburg Select-o-Matic 100”
17-002 Decals, water transfer, apply to inside of glass dome facing out,
original wording “7-INCH 45 RPM”, etc., original colors & shape, pair
17-003 Side glass, for left or right side of dome, edges are rounded as original, ea.
69-002 Mechanism cover, molded plastic, (primed, gray primer),
includes 100 Select-o-matic Mechanism insert
17-009 Insert for mechanism cover "100 Select-o-Matic Mechanism"
77-004 Program glass, taller, left or right, unprinted, all edges sanded for safety, ea.
77-005 Program glass, shorter, unprinted, all edges sanded for safety, (2), each
79-001 Divider trim for program glass, aluminum, left or right, without hole, each
79-002 Divider trim for program glass, aluminum, center, with hole (1)
17-006 Retainer, (frame), for program glass, Aluminum, Models B/BL only, 5 pc. set
68-008 Screw kit, stainless, for program-glass retainer & electrical selector, Phillips
head screws, 22 pcs, (16 wood & 6 metal screws, 1 extra of each included)
77-002 Instruction glass, Maroon, (Original Factory Color), Choose either Maroon
or Red, “PRESS ONE LETTER & MAKE SELECTIONS”, 2 piece set
77-060 Instruction glass, Red, (We have had many requests for this color),
“PRESS ONE LETTER & MAKE SELECTIONS”, 2 piece set
68-012 Speed washers, hold instruction glass in place, 10 pieces
77-003 Diffuser glass for Electrical Selector, white with red stripes
68-017 Thumb screw, holds Electrical selector in place, from the inside, (4), each
78-006 Latch bar solenoid for Electrical Selector, all metal frame, as original
78-020 Free play adapter, plugs in to existing credit unit, has switch for free play
or coin operation, eliminates latch bar solenoid burn-out, for Seeburg
Models: A, B, BL, C, G, W, R, J and JL, (This item is not discountable)
77-035 Select glass, green, Models M100A, B, BL and C
77-036 Select glass, blue, Models M100A, B, BL and C
77-040 Coins glass, red, for coin entry casting, Models M100B, BL and C
77-041 Coins glass, yellow, for coin entry casting, Models M100B, BL and C
77-042 Coins glass, dark blue for coin entry casting, Models M100B, BL and C
77-043 Coins glass, green, for coin entry casting, Models M100B, BL and C
68-014 Coin reject plunger, (button), plated, with scavenger wire, (Models A, B & C)
Specify # Title headings for Seeburg program holders, Specify: a color and the
A-1 part # from the list at the top of page 15, (11 or 12 piece assortment)
- 17 -
$47.50
250.00
10.00
15.00
18.00
125.00
6.50
5.00
5.00
16.50
16.50
150.00
5.00
16.00
16.00
3.50
10.00
1.50
60.00
68.95
6.50
6.50
6.50
6.50
6.50
6.50
25.00
10.00
SEEBURG M100B of 1950 – 51 & M100BL of 1951 – 52 (Continued)
A-1 PART #
73-080
73-081
73-082
73-083
73-084
68-007
73-090
73-091
73-092
73-093
73-094
73-095
73-096
73-097
73-098
73-099
83-004
83-001
83-002
83-003
83-035
84-015
84-001
84-002
84-003
84-004
84-005
84-020
74-009
83-007
78-010
83-010
83-011
78-002
Letter & # strips, (A1, B1, etc.), for program title holders, Red, 6 piece set
Letter & # strips, (A1, B1, etc.), for program title holders, Maroon, 6 piece set
Letter & # strips, (A1, B1, etc.), for program title holders, Aqua, 6 piece set
Letter & # strips, (A1, B1, etc.), for program title holders, Blue, 6 piece set
Letter & # strips, (A1, B1, etc.), for program title holders, Green, 6 piece set
Speed washers, round, hold letter/number strips & title headings to program
title holders. Also hold: 2 pc. Inst. glass; SELECT glass & COINS glass, 55 pieces
Coin instruction plastics for program title holders, 6 PLAYS – QUARTER,
2 PLAYS DIME, 1 PLAY NICKEL, Red, per pair
Coin instruction plastics for program title holders, 6 PLAYS – QUARTER,
2 PLAYS DIME, 1 PLAY NICKEL, Maroon, per pair
Coin instruction plastics for program title holders, 6 PLAYS – QUARTER,
2 PLAYS DIME, 1 PLAY NICKEL, Aqua, per pair
Coin instruction plastics for program title holders, 6 PLAYS – QUARTER,
2 PLAYS DIME, 1 PLAY NICKEL, Blue, per pair
Coin instruction plastics for program title holders, 6 PLAYS – QUARTER,
2 PLAYS DIME, 1 PLAY NICKEL, Green, per pair
Coin instruction plastics for program title holders, 3 PLAYS – QUARTER,
1 PLAY – DIME, Red, per pair
Coin instruction plastics for program title holders, 3 PLAYS – QUARTER,
1 PLAY – DIME, Maroon, per pair
Coin instruction plastics for program title holders, 3 PLAYS – QUARTER,
1 PLAY – DIME, Aqua, per pair
Coin instruction plastics for program title holders, 3 PLAYS – QUARTER,
1 PLAY – DIME, Blue, per pair
Coin instruction plastics for program title holders, 3 PLAYS – QUARTER,
1 PLAY – DIME, Green, per pair
Plastic Stripper plate (clear), complete with 2 stylus-cleaning brushes,
brush holders, and 6 screws, (all stainless steel hardware)
Plastic Stripper plate (clear), (with 6 stainless steel screws only)
Brush holders, hold stylus-cleaning brushes, (stainless steel), per pair
Brushes, stylus-cleaning, for plastic stripper plate, per pair
Stylus brush, Seeburg #405219, used to manually clean the styli
& the brushes on the stripper plate, (Pg. 13 & #31, pg. 1115 in the manual)
Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
Motor coupler, connects mech. motor to gear, (replace if rubber is hard)
Motor support plug, rubber, for under mechanism motor
Mechanism turntable drive bushings, Seeburg part # 245464, pair
Mechanism frame rubber bumper, Seeburg part # 245291, pair
Rubber cushion strips, (records rest on these while in the magazine),
front is square, Seeburg #245334, rear is round, #245468, per pair
Selector Coil & Armature Assembly, (a/k/a: Pin Bank), (Completely
dissembled & rebuilt), Specify: M100B/BL, M100C, HF100G, W100,
HF100R, 100J or 100JL, see page 64 for more information, each
Styli for original Pickering/Seeburg redhead cartridge, (.7 mil
diamond tip for all stereo and mono. records), per pair
Springs for tone arm, hand made in the U.S.A., exact replacements, pair
Trip switch, Micro, for tone arm, (for Models B through APFEAI)
Balance spring for Micro trip switch, for tone arm, each one is hand made
in the U.S.A., Seeburg part # 245817, (for Models B through APFEAI)
Spring for mechanism reversing switch, (Models B thru STD4), hand made
Trip coil for mechanism, Models B thru JL and V without 2050 for trip, ea.
- 18 -
$15.00
15.00
15.00
15.00
15.00
8.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
60.00
50.00
12.00
12.00
3.00
25.00
25.00
2.50
5.00
5.00
2.00
195.00
50.00
7.00
20.00
8.00
14.00
25.00
SEEBURG M100B of 1950 – 51 & M100BL of 1951 – 52 (Continued)
A-1 PART #
92-015 Capacitor, (run condenser), for mechanism motor, original style/metal can,
for M100A thru STD4, not SX100, for all USA motors, not for Nidec motors
83-009 Carriage roller for mechanism, Seeburg part # 245082, each
78-001 Cancel coil for Selector pin bank, Seeburg B/JL, (sleeve included, no plunger), ea.
78-031 Plunger & spring for cancel coil, for Selector pin bank, (two piece set), each
73-032 Selection playing plastic, indicates letter and number of record playing,
white letters & numbers w/red background, Models B & BL only, (A1 thru K10)
73-033 Selection playing plastic, indicates letter and number of record playing,
red letters & numbers w/white background, Models B & BL only, (A1 thru K10)
73-056 Selection playing plastic, indicates letter and number of record playing,
blue letters & numbers w/white background, Models B & BL only, (A1 thru K10)
68-010 Rivets, chrome plated, for selection playing plastic, (for Models B,
BL, C, G, W, R, J & VL200), 15 pcs.
73-036 Letter and number strip for record magazine, adhesive backed,
(for Models B, BL, C, G, W, R, J & JL), Specify: dark blue, aqua or red
73-037 Letter and number strips for popularity meter, adhesive backed
(for Models B, BL, C, G, W, R, J & JL), Specify: dark blue, aqua or red
73-038 Letter and number strip for selector coil frame, (pin cage), adhesive backed,
(for Models B, BL, C, G, W, R, J & JL), dark blue, (original color)
73-040 Letter and number strips for record magazine, popularity meter & pin cage,
(Models B, through JL), Specify: dark blue, aqua or red, complete 3 pc. set
17-007 Mirror for left and right end of mechanism (2), each
17-008 Masonite boards for Mech. end mirrors, pre cut to fit, pair
17-004 Frosted diffuser glass, 30” X 7 ¾”, for behind program title board
65-008 Foil, embossed, gold, ¼” diamonds, for cabinet interior, 18" X 72" roll,
cloth backed, use spray adhesive for installation, per roll
65-009 Foil, embossed, gold, ¼” squares, for cabinet interior, 18" X 72" roll,
cloth backed, use spray adhesive for installation, per roll
65-011 Foil, embossed, silver, ¼” diamonds, for cabinet interior, 18” X 72” roll,
cloth backed, use spray adhesive for installation, per roll
65-012 Foil, embossed, silver, ¼” squares, for cabinet interior, 18” X 72” roll,
cloth backed, use spray adhesive for installation, per roll
89-001 Interior labels, (lubrication diagram, etc., Models B, BL, C, G, W, R, J & JL)
17-018 Animation cradle tray with color sheet
17-010 Color sheet for animation cradle tray
86-004 Motor, 10 R.P.M. for animation tray, with threaded shaft, 100% U.S.A. made
86-005 Mounting bracket, metal, for animation motor, Models M100A, B & BL
17-020 Arm, attaches to animation motor & rotates, (1 end of drive link attaches to this)
17-016 Drive link, (one end attaches to animation cradle tray, other end to the Arm)
17-017 Hangers for animation cradle tray, 2 required, each
17-025 Animation tray complete, includes: tray, sheet, two hangers, drive link,
threaded shaft motor, motor mounting bracket and rotating arm
17-005 Glass above grill with printed silver stripe, 26” X 71/8”
65-002 Grill cloth, Specify: gold, red or silver, other colors are listed
on page 74 under GRILL CLOTH, cloth size 30” X 40”, each
17-013 Grill bars, mirror polished stainless steel, radius bend as original, 21 pc. set
68-001 Grill bar screws, stainless steel, (90 pcs.)
17-014 Grill triangles, mirror polished stainless steel, per pair
17-011 Mirror kit for all four sides of grill, 100-B, clear, (1/2" x 1" mirrors)
17-012 Mirror kit for all four sides of grill, 100-BL, blue, (1/2" x 1" mirrors)
17-023 Corner casting, not plated, for mirrors on outside of grill, (4), each
17-015 Vinyl base molding, color black, (74” X 2 7/16”), one piece
17-030 Vinyl base molding, color beige, (74” X 2 7/16”), one piece
- 19 -
$30.00
6.00
27.50
12.00
9.00
9.00
9.00
4.00
5.00
5.00
5.00
15.00
12.00
5.00
25.00
40.00
40.00
40.00
40.00
8.00
50.00
22.50
40.00
8.00
10.00
7.00
8.00
120.00
25.00
16.00
120.00
6.00
35.00
50.00
90.00
15.00
17.00
17.00
SEEBURG M100B of 1950 – 51 & M100BL of 1951 – 52 (Continued)
A-1 PART #
68-013 Tacks, Specify: bright nickel, brass or antique brass,
for vinyl base molding on Models BL & C only, 65 pc. set
17-019 Stainless steel base molding. B & BL only, brushed finish, w/all holes, 1 piece
76-004 Key for cabinet sides and back door, (not cash door), G219
67-004 Cash bag, (duck cloth, as original, hand made in the U.S.A.)
67-007 Cash door, superior grade birch covered plywood, with backup plates, (for
use with no metal frame around opening, Models A, B/BL and some C)
76-050 Lock, 1 1/8” quality lock, & 2 keys for Reproduction - wooden cash door
76-054 Lock, 1 1/8” quality lock, & 2 keys for lower back door,
(rotates one-half turn and key is removable in locked and open positions)
81-002 I.D. plate, Model B, (as original), no serial number, for back of cabinet
81-003 I.D. plate, Model BL, (as original), no serial number, for back of cabinet
67-017 Upper back door, Models B/BL only, birch covered plywood, w/wooden strip
on inside, bottom edge or door only, (Purchase this when all hardware can
be transferred from original door), (+ $20.00 for shipping an oversize box)
67-018 Upper back door, Models B/BL only, birch covered plywood, all hardware
is attached except for interior foil & exterior handles, (Purchase this when
the upper back door is missing), (add $20.00 for shipping an oversize box)
68-003 Hook latches & 4 screws for inside of upper back door, A, B/BL, C, G/W, pr.
67-008 Lower back door U-wood frame, (this item does not include any metal parts
that were included with the original frame), (add $10.00 for pack. & shipping)
67-009 Masonite amp & receiver cover, (fits into lower back door U-wood frame)
68-002 Safety chain for Lower back door, w/chain cover, mounting screw & key clip
68-026 Screws, hold Amp. & Receiver on lower back door, (4) 1”, (4) ½”, 65¢ ea. or 8 pcs.
66-002 Decals, water transfer, for lower back door, (On/Off & Vol. Control), 2 pc. set
66-005 Decals, Vinyl, peel & stick, for lower back door, (On/Off & Vol. Control), 2 pc. set
92-037 Capacitor kits for Amplifiers used in Seeburg Models: A, B, C, G & W,
Specify: Amplifier # MRA1-L6 through MRA4-L6, includes:
Schematics and replacement values reference sheet, each kit
92-051 Capacitor kit for WSR5-L6, Selection Receiver, includes: schematics and
replacement values reference sheet, (does not include cap. for wallboxes)
92-025 Capacitor for Stepper, operates wallboxes in Seeburgs: M100A thru LPC480
37-009 Fuse, 3 amp or 3 2/10 amp Fustat, large screw in type, for Seeburg: M100A
thru VL200 Selection Receivers, (these are for the operation of wallboxes)
91-003 Volume control pot. for Models 146, 147, 148, A, B/BL, C, G, W & R
76-001 Volume control key for original pots., (Seeburg amps. thru SHFA2 & all Wurlitzer’s)
72-004 Bulb, miniature #47 (selection indicator) (2), & (behind select glass) (2), ea.
72-011 Bulb, miniature #81 (behind Mech. cover insert) (1)
70-011 Fluorescent lamp 25 watt 33" T12, daylight, recommended color (1)
70-010 Fluorescent lamp 25 watt 33" T12, cool white, optional color
70-050 Colored sleeve for T12 fluorescent lamp, (cut to your specified length),
Specify: sleeve color: red, blue, green, yellow or pink, per foot
71-006 Ballast, 25 watt, for 1 lamp, new style, (clamped core), made in the U.S.A.
71-035 Ballast, 25 watt, for 1 lamp, original style case & Black color, (Now thermally
protected), made in the U.S.A., includes 2 rubber grommets for mounting
71-028 Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
71-030 Outlet, 3-wire grounded duplex receptacle, (The Receiver plugs into this)
68-004 Caster sockets, use with original Seeburg metal casters or our 2 ½” hard
rubber replacement casters, (made by original supplier to Seeburg), each
68-005 Casters 2 ½” hard rubber, (made by original supplier to Seeburg), each
- 20 -
$7.00
70.00
7.00
12.00
18.00
10.00
10.00
15.00
15.00
80.00
105.00
10.00
45.00
45.00
10.00
5.00
10.00
8.00
65.00
27.50
12.00
8.00
30.00
3.00
1.00
2.00
10.00
10.00
1.75
12.00
20.00
1.50
12.00
8.00
3.00
7.00
SEEBURG M100C of 1952 – 1953 50 Records (100 Selections)
A-1 PART #
80-024
80-025
80-026
18-001
66-003
66-001
18-003
69-002
18-008
77-004
77-005
79-001
79-002
18-006
68-008
77-002
77-060
68-012
77-003
68-017
78-006
78-020
77-035
77-036
77-040
77-041
77-042
77-043
68-014
Specify #
73-080
73-081
73-082
73-083
73-084
68-007
73-090
73-091
73-092
Service & parts manual, Seeburg M100C, 148 pages, order R-259
Installation, Operation – Troubleshooting guide, M100C, 52 pgs., order R-433
Seeburg M100C, Purchase R-259 and R-433, save $10.00, order R-259A
Glass dome, with printed logo, (add $40 for packaging & shipping)
Decal, water transfer, apply to inside of glass dome facing out,
original wording, colors and font, “Seeburg Select-o-Matic 100”
Cloud-shaped pricing decals, water transfer to inside of glass, 5 to choose
from, Specify: 1/5¢ Special 6/25¢; 2/10¢ Special 6/25¢; 2/10¢ Special 5/25¢;
1/10¢ Special 3/25¢ or Special 1 play for 25¢, (large size: 5” x 4”), each
Side Glass, for left or right side of dome, edges rounded as original, ea.
Mechanism cover, molded plastic, (primed, gray primer),
includes 100 Select-o-matic Mechanism insert
Insert for mechanism cover, red lettering, "100 Select-o-Matic Mechanism"
Program glass, taller, left or right, unprinted, all edges sanded for safety, ea.
Program glass, shorter, unprinted, all edges sanded for safety, (2), each
Divider trim for program glass, aluminum, left or right, without hole, each
Divider trim for program glass, aluminum, center, with hole, each
Retainer, (frame), for program glass, Aluminum, Model C only, 5 pc. set
Screw kit, stainless, for program-glass retainer & electrical selector, Phillips
head screws, 22 pcs, (16 wood & 6 metal screws, 1 extra of each included)
Instruction glass, Maroon, (Original Factory Color), Choose either Maroon
or Red, “PRESS ONE LETTER & MAKE SELECTIONS”, 2 piece set
Instruction glass, Red, (We have had many requests for this color),
“PRESS ONE LETTER & MAKE SELECTIONS”, 2 piece set
Speed washers, hold instruction glass in place, 10 pieces
Diffuser glass for Electrical Selector, white with red stripes
Thumb screw, holds Electrical selector in place, from the inside, (4), each
Latch bar solenoid for Electrical Selector, all metal frame, as original
Free play adapter, plugs in to existing credit unit, has switch for free play
or coin operation, eliminates latch bar solenoid burn-out, for Seeburg
Models: A, B, BL, C, G, W, R, J and JL, (This item is not discountable)
Select glass, green, Models M100A, B, BL and C
Select glass, blue, Models M100A, B, BL and C
Coins glass, red, for coin entry casting, Models M100B, BL and C
Coins glass, yellow, for coin entry casting, Models M100B, BL and C
Coins glass, dark blue for coin entry casting, Models M100B, BL and C
Coins glass, green, for coin entry casting, Models M100B, BL and C
Coin reject plunger, (button), plated, with scavenger wire, (Models A, B & C)
Title headings for Seeburg program holders, Specify: a color and the
A-1 part # from the list at the top of page 15, (11 or 12 piece assortment)
Letter & # strips, (A1, B1, etc.), for program title holders, Red, 6 piece set
Letter & # strips, (A1, B1, etc.), for program title holders, Maroon, 6 piece set
Letter & # strips, (A1, B1, etc.), for program title holders, Aqua, 6 piece set
Letter & # strips, (A1, B1, etc.), for program title holders, Blue, 6 piece set
Letter & # strips, (A1, B1, etc.), for program title holders, Green, 6 piece set
Speed washers, round, hold letter/number strips & title headings to program
title holders. Also hold: 2 pc. Inst. glass; SELECT glass & COINS glass, 55 pieces
Coin instruction plastics for program title holders, 6 PLAYS – QUARTER,
2 PLAYS DIME, 1 PLAY NICKEL, Red, per pair
Coin instruction plastics for program title holders, 6 PLAYS – QUARTER,
2 PLAYS DIME, 1 PLAY NICKEL, Maroon, per pair
Coin instruction plastics for program title holders, 6 PLAYS – QUARTER,
2 PLAYS DIME, 1 PLAY NICKEL, Aqua, per pair
- 21 -
$42.50
31.00
63.50
275.00
10.00
9.00
25.00
125.00
6.50
5.00
5.00
16.50
16.50
150.00
5.00
16.00
16.00
3.50
10.00
1.50
60.00
68.95
6.50
6.50
6.50
6.50
6.50
6.50
25.00
10.00
15.00
15.00
15.00
15.00
15.00
8.00
7.00
7.00
7.00
SEEBURG M100C of 1952 – 1953 (Continued)
A-1 PART #
73-093 Coin instruction plastics for program title holders, 6 PLAYS – QUARTER,
2 PLAYS DIME, 1 PLAY NICKEL, Blue, per pair
73-094 Coin instruction plastics for program title holders, 6 PLAYS – QUARTER,
2 PLAYS DIME, 1 PLAY NICKEL, Green, per pair
73-095 Coin instruction plastics for program title holders, 3 PLAYS – QUARTER,
1 PLAY – DIME, Red, per pair
73-096 Coin instruction plastics for program title holders, 3 PLAYS – QUARTER,
1 PLAY – DIME, Maroon, per pair
73-097 Coin instruction plastics for program title holders, 3 PLAYS – QUARTER,
1 PLAY – DIME, Aqua, per pair
73-098 Coin instruction plastics for program title holders, 3 PLAYS – QUARTER,
1 PLAY – DIME, Blue, per pair
73-099 Coin instruction plastics for program title holders, 3 PLAYS – QUARTER,
1 PLAY – DIME, Green, per pair
83-004 Plastic Stripper plate (clear), complete with 2 stylus-cleaning brushes,
brush holders, and 6 screws, (all stainless steel hardware)
83-001 Plastic Stripper plate (clear), (with 6 stainless steel screws only)
83-002 Brush holders, hold stylus-cleaning brushes, (stainless steel), per pair
83-003 Brushes, stylus-cleaning, for plastic stripper plate, per pair
83-035 Stylus brush, Seeburg #405219, used to manually clean the styli
& the brushes on the stripper plate, (#34 on page 1149 in the manual)
84-015 Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
84-001 Motor coupler, connects mech. motor to gear, (replace if rubber is hard)
84-002 Motor support plug, rubber, for under mechanism motor
84-003 Mechanism turntable drive bushings, Seeburg part # 245464, pair
84-004 Mechanism frame rubber bumper, Seeburg part # 245291, pair
84-005 Rubber cushion strips, (records rest on these while in the magazine),
front is square, Seeburg #245334, rear is round, #245468, per pair
84-020 Selector Coil & Armature Assembly, (a/k/a: Pin Bank), (Completely
dissembled & rebuilt), Specify: M100B/BL, M100C, HF100G, W100,
HF100R, 100J or 100JL, see page 64 for more information, each
74-009 Styli for original Pickering/Seeburg redhead cartridge, (.7 mil
diamond tip for all stereo and mono. records), per pair
83-007 Springs for tone arm, hand made in the U.S.A., exact replacements, pair
78-010 Trip switch, Micro, for tone arm, (for Models B through APFEAI)
83-010 Balance spring for Micro trip switch, for tone arm, each one is hand made
in the U.S.A., Seeburg part # 245817, (for Models B through APFEAI)
83-011 Spring for mechanism reversing switch, (Models B thru STD4), hand made
78-002 Trip coil for mechanism, Models B thru JL and V without 2050 for trip, ea.
92-015 Capacitor, (run condenser), for mechanism motor, original style/metal can,
for M100A thru STD4, not SX100, for all USA motors, not for Nidec motors
83-009 Carriage roller for mechanism, Seeburg part # 245082, each
78-001 Cancel coil for Selector pin bank, Seeburg B/JL, (sleeve included, no plunger), ea.
78-031 Plunger & spring for cancel coil, for Selector pin bank, (two piece set), each
88-006 Spray paint, Seeburg C Yellow, for mech. frame, acrylic enamel, 12 oz. can
88-007 Spray paint, Seeburg C Aqua-Blue, for mech. cover, acrylic enamel, 12 oz. can
18-004 Decals, water transfer, Oval 45 R.P.M. record, for mech. ends, pair
73-034 Selection playing plastic, indicates letter and number of record playing,
aqua letters & numbers w/white background, Model C only, (A1 thru K10)
68-010 Rivets, chrome plated, for selection playing plastic, (Models B thru VL200), 15 pcs.
73-036 Letter and number strip for record magazine, adhesive backed,
(for Models B, BL, C, G, W, R, J & JL), Specify: dark blue, aqua or red
- 22 -
$7.00
7.00
7.00
7.00
7.00
7.00
7.00
60.00
50.00
12.00
12.00
3.00
25.00
25.00
2.50
5.00
5.00
2.00
195.00
50.00
7.00
20.00
8.00
14.00
25.00
30.00
6.00
27.50
12.00
16.00
16.00
11.00
9.00
4.00
5.00
SEEBURG M100C of 1952 – 1953 (Continued)
A-1 PART #
73-037 Letter and number strips for popularity meter, adhesive backed
(for Models B, BL, C, G, W, R, J & JL), Specify: dark blue, aqua or red
73-038 Letter and number strip for selector coil frame, (pin cage), adhesive backed,
(for Models B, BL, C, G, W, R, J & JL), dark blue, (original color)
73-040 Letter and number strips for record magazine, popularity meter & pin cage,
(Models B, through JL), Specify: dark blue, aqua or red, complete 3 pc. set
18-007 Mirror kit, exact size mirrors, for frames at each end of mechanism, this
package has four pre-cut panels and a few extra mirrors, complete set
18-020 Mirrors, exact size mirrors, for frames at each end of mechanism, this
package has 1 full sheet, Purchaser must cut panels, complete set + extras
68-030 Screws (6) and washers (6), stainless steel, hold mirror frames in place at
both ends of mechanism, (screw heads were originally painted red), 12 pc. set
67-010 Masonite boards for Mech. end mirrors, cut to fit, (flat, not mounded), pair
18-005 Frosted diffuser glass, 30” X 7”, for behind program title board
65-003 Foil, embossed, gold, ½” pillowed squares, for interior of Seeburg C,
Wurlitzer 1080 & 1100, 32” X 16” sheet, (2 sheets required), per sheet
65-008 Foil, embossed, gold, ¼” diamonds, for cabinet interior, 18" X 72" roll,
cloth backed, use spray adhesive for installation, per roll
65-009 Foil, embossed, gold, ¼” squares, for cabinet interior, 18" X 72" roll,
cloth backed, use spray adhesive for installation, per roll
65-011 Foil, embossed, silver, ¼” diamonds, for cabinet interior, 18” X 72” roll,
cloth backed, use spray adhesive for installation, per roll
65-012 Foil, embossed, silver, ¼” squares, for cabinet interior, 18” X 72” roll,
cloth backed, use spray adhesive for installation, per roll
89-001 Interior labels, (lubrication diagram, etc., Models B, BL, C, G, W, R, J & JL)
65-002 Grill cloth, Specify: gold, red or silver, other colors are listed
on page 74 under GRILL CLOTH, cloth size 30” X 40”, each
18-010 Clear plastic Grill tube, with mirrored Mylar insert, excellent replacement,
can be mingled with original glass tubes, best available, 12 required, each
18-011 Clear plastic Grill tubes, with mirrored Mylar inserts, excellent replacements,
best available, (Special: save $30.00 per 12 piece set), (This item is not
discountable at the 12 piece price), per 12 piece set
18-012 Grill tube brackets (spoons or holders), each
86-002 Drop in animation assemblies, quiet synchronized motors, brilliant
colors using Ken Arnold reproduction color sheets, complete units,
perfect fit, (plug-in directly to 110 volts), 100% U.S.A. made, per pair
86-001 Color sheets only, for animation, 1 left and 1 right, brilliant colors, per pair
18-013 Pilaster plastics white (frosted crystallization, inside, as original), choose
white for painted cabinets, or stained cabinets with very light color stain, pair
18-014 Pilaster plastics off-white/beige (frosted crystallization, inside, as original),
choose off-white/beige for medium or dark color stained cabinets, per pair
18-017 Wooden toe for below front of pilaster plastic, M100C only (2), each
86-003 Motor for original animation, includes mounting bracket & sprocket
18-015 Vinyl base molding, color - black, 2 pieces, per pair
18-016 Vinyl base molding, color - beige, 2 pieces, per pair
68-013 Tacks, Specify: bright nickel, brass or antique brass,
for vinyl base molding on Models BL & C only, 65 pc. set
76-005 Key for cabinet sides and back door, (not cash door), G245
67-004 Cash bag, (duck cloth, as original, hand made in the U.S.A.)
67-007 Cash door, superior grade birch covered plywood, with backup plates, (for
use with no metal frame around opening, Models A, B/BL and some C)
67-012 Cash door, superior grade birch covered plywood, with backup plates,
(for use with metal frame around opening, Models C through LS3)
- 23 -
$5.00
5.00
15.00
50.00
55.00
3.50
6.00
25.00
40.00
40.00
40.00
40.00
40.00
8.00
16.00
15.75
159.00
6.00
285.00
28.00
210.00
210.00
29.00
70.00
15.00
15.00
7.00
7.00
12.00
18.00
18.00
SEEBURG M100C of 1952 – 1953 (Continued)
A-1 PART #
76-050 Lock, 1 1/8” quality lock, & 2 keys for Reproduction - wooden cash door
76-051 Lock, 1 1/8” quality lock, hardware, & 2 keys for Original metal cash door
76-054 Lock, 1 1/8” quality lock, & 2 keys for lower back door,
(rotates one-half turn and key is removable in locked and open positions)
81-004 I.D. plate, Model C, (as original), no serial number, for back of cabinet
67-019 Upper back door, Model M100C only, birch covered plywood, wooden strip
on inside, bottom edge or door only, (Purchase this when all hardware can
be transferred from original door), (+ $20.00 for shipping an oversize box)
67-020 Upper back door, Model M100C only, birch covered plywood, all hardware
is attached except for interior top trim & exterior handles, (Purchase this
when upper back door is missing), (+ $20.00 for shipping an oversize box)
83-025 Top trim for inside upper back door, stainless steel, original shape, 19” wide
68-003 Hook latches & 4 screws for inside of upper back door, A, B/BL, C, G/W, pr.
67-008 Lower back door U-wood frame, (this item does not include any metal parts
that were included with the original frame), (+ $10.00 for pack. & shipping)
67-009 Masonite amp & receiver cover, (fits into lower back door U-wood frame)
68-002 Safety chain for Lower back door, w/chain cover, mounting screw & key clip
68-026 Screws, hold Amp. & Receiver on lower back door, (4) 1”, (4) ½”, 65¢ ea. or 8 pcs.
66-002 Decals, water transfer, for lower back door, (On/Off & Vol. Control), 2 pc. set
66-005 Decals, Vinyl, peel & stick, for lower back door, (On/Off & Vol. Control), 2 pc. set
92-037 Capacitor kits for Amplifiers used in Seeburg Models: A, B, C, G & W,
Specify: Amplifier # MRA1-L6 through MRA4-L6, includes:
Schematics and replacement values reference sheet, each kit
92-051 Capacitor kit for WSR5-L6, Selection Receiver, includes: schematics and
replacement values reference sheet, (does not include cap. for wallboxes)
92-052 Capacitor kit for WSR7-L6, Selection Receiver, includes: schematics and
replacement values reference sheet, (does not include cap. for wallboxes)
92-025 Capacitor for Stepper, operates wallboxes in Seeburgs: M100A thru LPC480
37-009 Fuse, 3 amp or 3 2/10 amp Fustat, large screw in type, for Seeburg: M100A
thru VL200 Selection Receivers, (these are for the operation of wallboxes)
91-003 Volume control pot. for Models 146, 147, 148, A, B/BL, C, G, W & R
76-001 Volume control key for original pots., (Seeburg amps. thru SHFA2 & all Wurlitzer’s)
72-003 Bulb, miniature #44 (selection indicator lamps) (2 required), each
72-004 Bulb, miniature #47 (behind select glass) (2 required), each
72-011 Bulb, miniature #81 (behind Mech. cover insert) (1)
70-007 Fluorescent lamp 20 watt 24" T12, daylight, recommended color (2), each
70-006 Fluorescent lamp 20 watt 24" T12, cool white, optional color, each
70-011 Fluorescent lamp 25 watt 33" T12, daylight, recommended color (1)
70-010 Fluorescent lamp 25 watt 33" T12, cool white, optional color
70-050 Colored sleeve for T12 fluorescent lamp, (cut to your specified length),
Specify: sleeve color: red, blue, green, yellow or pink, per foot
71-001 Ballast 14 to 20 watt, for 1 lamp, new square style, clamped core, white, each
71-006 Ballast, 25 watt, for 1 lamp, new style, (clamped core), made in the U.S.A.
71-035 Ballast, 25 watt, for 1 lamp, original style case & Black color, (Now thermally
protected), made in the U.S.A., includes 2 rubber grommets for mounting
71-028 Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
71-030 Outlet, 3-wire grounded duplex receptacle, (The Receiver plugs into this)
68-004 Caster sockets, use with original Seeburg metal casters or our 2 ½” hard
rubber replacement casters, (made by original supplier to Seeburg), each
68-005 Casters 2 ½” hard rubber, (made by original supplier to Seeburg), each
- 24 -
$10.00
10.00
10.00
15.00
80.00
105.00
22.50
10.00
45.00
45.00
10.00
5.00
10.00
8.00
65.00
27.50
27.50
12.00
8.00
30.00
3.00
1.00
1.00
2.00
7.00
7.00
10.00
10.00
1.75
12.00
12.00
20.00
1.50
12.00
8.00
3.00
7.00
SEEBURG HF100G & W100 of 1953 – 54 50 Records (100 Selections)
A-1 PART #
80-028
80-029
80-030
19-001
66-003
66-001
19-002
69-002
19-004
77-007
Service & parts manual, Seeburg HF100G & W100, 155 pgs., order R-266
Installation, Operation – Troubleshooting, G & W, 94 pages, order R-226
Seeburg G & W, Purchase R-266 and R-226, save $10.00, order R-266A
Glass dome, with printed logo, (add $40 for packaging & shipping)
Decal, water transfer, apply to inside of glass dome facing out,
original wording, colors and font, “Seeburg Select-o-Matic 100”
Cloud-shaped pricing decals, water transfer to inside of glass, 5 to choose
from, Specify: 1/5¢ Special 6/25¢; 2/10¢ Special 6/25¢; 2/10¢ Special 5/25¢;
1/10¢ Special 3/25¢ or Special 1 play for 25¢, (large size: 5” x 4”), each
Side Glass, for left or right side of dome, each
Mechanism cover, molded plastic, (primed, gray primer),
Includes SELECT-O-MATIC 100 insert
Mechanism cover insert, SELECT-O-MATIC 100
Program glass, for models: G, W, R, J & JL, (letters & numbers are baked on,
Exact, original, font & color, all edges of glass are sanded), 5 piece set
$40.00
35.00
65.00
285.00
10.00
9.00
35.00
125.00
6.50
45.00
77-008 Program glass, for models: G, W, R, J & JL, single pieces, (letters & #s are
baked on, original font & color: A1/B1, C1/D1, E1/F1, G1/H1 or J1/K1), each
12.50
64-010 Sponge rubber gasket, for program glass, $0.90 per foot or one piece, (40”)
3.00
77-009 Instruction glass, 3 colors, 2 pc. set, “6 PLAYS QUARTER”, Original Maroon color
77-065 Instruction glass, 3 colors, 2 pc. set, “6 PLAYS QUARTER”, Popular Red color
16.00
16.00
77-010 Instruction glass, 3 colors, 2 pc. set, “3 PLAYS QUARTER”, Original Maroon color
77-067 Instruction glass, 3 colors, 2 pc. set, “3 PLAYS QUARTER”, Popular Red color
16.00
16.00
77-011 Instruction glass, 3 colors, 2 pc. set, “25¢ PER SELECTN.”, Original Maroon color
16.00
68-012 Speed washers, hold instruction glass in place, 10 pieces
78-006 Latch bar solenoid for Electrical Selector, all metal frame, as original
78-020 Free play adapter, plugs in to existing credit unit, has switch for free play
or coin operation, eliminates latch bar solenoid burn-out, for Seeburg
Models: A, B, BL, C, G, W, R, J and JL, (This item is not discountable)
77-050 Select glass, Seeburg G, W, R, J, JL, L100 and 101, green
77-051 Select glass, Seeburg G, W, R, J, JL, L100 and 101, blue
68-015 Coin reject plunger, plated, with scavenger wire, (Models G thru APFEAI)
Specify # Title headings for Seeburg program holders, Specify: a color and the
A-1 part # from the list at the top of page 15, (11 or 12 piece assortment)
83-004 Plastic Stripper plate (clear), complete with 2 stylus-cleaning brushes,
brush holders, and 6 screws, (all stainless steel hardware)
83-001 Plastic Stripper plate (clear), (with 6 stainless steel screws only)
83-002 Brush holders, hold stylus-cleaning brushes, (stainless steel), per pair
83-003 Brushes, stylus-cleaning, for plastic stripper plate, per pair
83-035 Stylus brush, Seeburg #405219, used to manually clean the styli
& the brushes on the stripper plate, (Pg. 1172 & #14, pg. 1181 in the manual)
84-015 Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
84-001 Motor coupler, connects mech. motor to gear, (replace if rubber is hard)
84-002 Motor support plug, rubber, for under mechanism motor
84-003 Mechanism turntable drive bushings, Seeburg part # 245464, pair
84-004 Mechanism frame rubber bumper, Seeburg part # 245291, pair
84-005 Rubber cushion strips, (records rest on these while in the magazine),
front is square, Seeburg #245334, rear is round, #245468, per pair
84-020 Selector Coil & Armature Assembly, (a/k/a: Pin Bank), (Completely
dissembled & rebuilt), Specify: M100B/BL, M100C, HF100G, W100,
HF100R, 100J or 100JL, see page 64 for more information, each
- 25 -
3.50
60.00
68.95
6.50
6.50
25.00
10.00
60.00
50.00
12.00
12.00
3.00
25.00
25.00
2.50
5.00
5.00
2.00
195.00
SEEBURG HF100G and W100 of 1953 – 1954 (Continued)
A-1 PART #
74-009 Styli for original Pickering/Seeburg redhead cartridge, (.7 mil
diamond tip for all stereo and mono. records), per pair
83-007 Springs for tone arm, hand made in the U.S.A., exact replacements, pair
78-010 Trip switch, Micro, for tone arm, (for Models B through APFEAI)
83-010 Balance spring for Micro trip switch, for tone arm, each one is hand made
in the U.S.A., Seeburg part # 245817, (for Models B through APFEAI)
83-011 Spring for mechanism reversing switch, (Models B thru STD4), hand made
83-012 Spring for snap switch for electrical selector, (Models G & W only), each
78-002 Trip coil for mechanism, Models B thru JL and V without 2050 for trip, ea.
92-015 Capacitor, (run condenser), for mechanism motor, original style/metal can,
for M100A thru STD4, not SX100, for all USA motors, not for Nidec motors
83-009 Carriage roller for mechanism, Seeburg part # 245082, each
78-001 Cancel coil for Selector pin bank, Seeburg B/JL, (sleeve included, no plunger), ea.
78-031 Plunger & spring for cancel coil, for Selector pin bank, (two piece set), each
88-008 Spray paint, Red, for Model G magazine and mechanism frame, also for
Model W entire mech. except for mech. cover, acrylic enamel, 12 oz. can
88-009 Spray paint, Dark Blue, for HF100G & W100, for metal grill on front, 12 oz. can
88-010 Spray paint, Light Blue, for HF100G, for mechanism cover,
mechanism end caps, etc., acrylic enamel, 12 oz. can
19-005 Decals, water transfer, Round 45 R.P.M. for Mech. ends, pair
73-035 Selection playing plastic, indicates letter and number of record playing, dark
blue letters & numbers w/white background, Models G, W, & R, (A1 thru K0)
68-010 Rivets, chrome plated, for selection playing plastic, (for Models B,
BL, C, G, W, R, J & VL200), 15 pcs.
73-036 Letter and number strip for record magazine, adhesive backed,
(for Models B, BL, C, G, W, R, J & JL), Specify: dark blue, aqua or red
73-037 Letter and number strips for popularity meter, adhesive backed
(for Models B, BL, C, G, W, R, J & JL), Specify: dark blue, aqua or red
73-038 Letter and number strip for selector coil frame, (pin cage), adhesive backed,
(for Models B, BL, C, G, W, R, J & JL), dark blue, (original color)
73-040 Letter and number strips for record magazine, popularity meter & pin cage,
(Models B, through JL), Specify: dark blue, aqua or red, complete 3 pc. set
19-006 Mirror kit, exact diagonal cut, for frames at each end of mechanism, this
package has four pre-cut panels and a few extra mirrors, complete set
19-015 Mirrors, exact diagonal cut, for frames at each end of mechanism, this
package has 1 full sheet, Purchaser must cut panels, complete set + extras
68-030 Screws (6) and washers (6), stainless steel, hold mirror frames in place at
both ends of mechanism, (screw heads were originally painted red), 12 pc. set
67-010 Masonite boards for Mech. end mirrors, cut to fit, (flat, not mounded), pair
19-003 Frosted diffuser glass, 31 ¾” X 5 ¾”, for behind program title board
65-008 Foil, embossed, gold, ¼” diamonds, for cabinet interior, 18" X 72" roll,
cloth backed, use spray adhesive for installation, per roll
65-009 Foil, embossed, gold, ¼” squares, for cabinet interior, 18" X 72" roll,
cloth backed, use spray adhesive for installation, per roll
65-011 Foil, embossed, silver, ¼” diamonds, for cabinet interior, 18” X 72” roll,
cloth backed, use spray adhesive for installation, per roll
65-012 Foil, embossed, silver, ¼” squares, for cabinet interior, 18” X 72” roll,
cloth backed, use spray adhesive for installation, per roll
89-001 Interior labels, (lubrication diagram, etc., Models B, BL, C, G, W, R, J & JL)
65-002 Grill cloth, Specify: gold, red or silver, other colors are listed
on page 74 under GRILL CLOTH, cloth size 30” X 40”, each
- 26 -
$50.00
7.00
20.00
8.00
14.00
14.00
25.00
30.00
6.00
27.50
12.00
16.00
16.00
16.00
10.00
9.00
4.00
5.00
5.00
5.00
15.00
75.00
80.00
3.50
6.00
25.00
40.00
40.00
40.00
40.00
8.00
16.00
SEEBURG HF100G and W100 of 1953 – 1954 (Continued)
A-1 PART #
86-002 Drop in animation assemblies, quiet synchronized motors, brilliant
colors using Ken Arnold reproduction color sheets, complete units,
perfect fit, (plug-in directly to 110 volts), 100% U.S.A. made, per pair
86-001 Color sheets only, for animation, 1 left and 1 right, brilliant colors, pair
19-007 G Pilaster plastics, white, (frosted crystallization, inside), replacements
for original stainless steel pilasters, choose white for painted cabinets,
or cabinets that are stained with a very light color stain, per pair
19-008 G Pilaster plastics, off white, (frosted crystallization, inside),
replacements for original stainless steel pilasters, choose off-white/beige
for medium to dark color stained cabinets, per pair
19-009 W Pilaster plastics, available in white only, (frosted crystallization
inside & exact “patch quilt pattern” printed outside, as original), per pair
76-006 Key for cabinet sides and back door, (not cash door), F221
67-004 Cash bag, (duck cloth, as original, hand made in the U.S.A.)
67-012 Cash door, superior grade birch covered plywood, with backup plates,
(for use with metal frame around opening, Models C through LS3)
76-050 Lock, 1 1/8” quality lock, & 2 keys for Reproduction - wooden cash door
76-051 Lock, 1 1/8” quality lock, hardware, & 2 keys for Original metal cash door
76-054 Lock, 1 1/8” quality lock, & 2 keys for lower back door,
(rotates one-half turn and key is removable in locked and open positions)
81-005 I.D. plate, Model G only, (as original), no serial number, for back of cabinet
81-037 I.D. plate, Model W only, (printed HF100W), no serial #, for back of cabinet
67-015 Upper back door, Models G/W only, birch covered plywood, w/wooden strip
on inside, bottom edge or door only, (Purchase this when all hardware can
be transferred from original door), (+ $20.00 for shipping an oversize box)
67-016 Upper back door, Models G/W only, birch covered plywood, all hardware is
attached except for interior top trim & exterior handles, (Purchase this item
when upper back door is missing), (+ $20.00 for shipping an oversize box)
83-025 Top trim for inside upper back door, stainless steel, original shape, 19” wide
68-003 Hook latches & 4 screws for inside of upper back door, A, B/BL, C, G/W, pr.
67-008 Lower back door U-wood frame, (this item does not include any metal parts
that were included with the original frame), (+ $10.00 for pack. & shipping)
67-009 Masonite amp & receiver cover, (fits into lower back door U-wood frame)
68-002 Safety chain for Lower back door, w/chain cover, mounting screw & key clip
68-026 Screws, hold Amp. & Receiver on lower back door, (4) 1”, (4) ½”, 65¢ ea. or 8 pcs.
66-002 Decals, water transfer, for lower back door, (On/Off & Vol. Control), 2 pc. set
66-005 Decals, Vinyl, peel & stick, for lower back door, (On/Off & Vol. Control), 2 pc. set
92-037 Capacitor kits for Amplifiers used in Seeburg Models: A, B, C, G & W,
Specify: Amplifier # MRA1-L6 through MRA4-L6, includes:
Schematics and replacement values reference sheet, each kit
92-051 Capacitor kit for WSR5-L6, Selection Receiver, includes: schematics and
replacement values reference sheet, (does not include cap. for wallboxes)
92-052 Capacitor kit for WSR7-L6, Selection Receiver, includes: schematics and
replacement values reference sheet, (does not include cap. for wallboxes)
92-025 Capacitor for Stepper, operates wallboxes in Seeburgs: M100A thru LPC480
37-009 Fuse, 3 amp or 3 2/10 amp Fustat, large screw in type, for Seeburg: M100A
thru VL200 Selection Receivers, (these are for the operation of wallboxes)
91-003 Volume control pot. for Models 146, 147, 148, A, B/BL, C, G, W & R
76-001 Volume control key for original pots., (Seeburg amps. thru SHFA2 & all Wurlitzer’s)
72-003 Bulb, miniature #44 (selection indicator lamps) (2 required), each
72-004 Bulb, miniature #47 (behind credit glass) (2 required), each
72-011 Bulb, miniature #81 (behind mech. cover insert) (1)
- 27 -
$285.00
28.00
285.00
285.00
310.00
7.00
12.00
18.00
10.00
10.00
10.00
15.00
15.00
80.00
105.00
22.50
10.00
45.00
45.00
10.00
5.00
10.00
8.00
65.00
27.50
27.50
12.00
8.00
30.00
3.00
1.00
1.00
2.00
SEEBURG HF100G and W100 of 1953 – 1954 (Continued)
A-1 PART #
70-007
70-006
70-011
70-010
70-050
71-001
71-006
71-035
71-028
71-016
71-030
71-026
19-010
68-004
68-005
Fluorescent lamp 20 watt 24" T12, daylight, for Models with animation (2), ea.
Fluorescent lamp 20 watt 24" T12, cool white, optional color, animation
Fluorescent lamp 25 watt 33" T12, daylight, recommended color (1)
Fluorescent lamp 25 watt 33" T12, cool white, optional color
Colored sleeve for T12 fluorescent lamp, (cut to your specified length),
Specify: sleeve color: red, blue, green, yellow or pink, per foot
Ballast 14 to 20 watt, for 1 lamp, new square style, clamped core, white, each
Ballast, 25 watt, for 1 lamp, new style, (clamped core), made in the U.S.A.
Ballast, 25 watt, for 1 lamp, original style case & Black color, (Now thermally
protected), made in the U.S.A., includes 2 rubber grommets for mounting
Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
Outlet, 3-wire grounded duplex receptacle, (The Receiver plugs into this)
Outlet, vinyl cube tap for A. C. socket in all Receivers & Selector Units,
(Seeburg’s M100A through DS160), converts the socket to 3 A. C. outlets
Stainless Steel base trim plates, mirror polished, per pair
Caster sockets, use with original Seeburg metal casters or our 2 ½” hard
rubber replacement casters, (made by original supplier to Seeburg), each
Casters 2 ½” hard rubber, (made by original supplier to Seeburg), each
$7.00
7.00
10.00
10.00
1.75
12.00
12.00
20.00
1.50
12.00
8.00
3.00
50.00
3.00
7.00
SEEBURG HF100R of 1954 – 1955, 100J & 100JL of 1955 – 57
50 Records (100 Selections)
A-1 PART #
80-031
80-032
80-033
20-001
20-023
20-024
20-025
66-001
20-006
69-003
69-010
69-004
20-026
20-027
68-050
68-051
Service & parts manual, Seeburg R, J & JL, 177 pages, order R-267
Installation, Operation - Troubleshooting, R, J & JL, 70 pages, order R-426
Seeburg R, J & JL, Purchase R-267 and R-426, save $10.00, order R-267A
Glass dome, with printed logo, (add $40 for packaging & shipping)
Decal for dome glass, water transfer, Blue & white, Seeburg HIGH FIDELITY
Decal for dome glass, water transfer, Red & white, Seeburg HIGH FIDELITY
Decal for dome glass, water transfer, Gold & white, Seeburg HIGH FIDELITY
Cloud-shaped pricing decals, water transfer to inside of glass, 5 to choose
from, Specify: 1/5¢ Special 6/25¢; 2/10¢ Special 6/25¢; 2/10¢ Special 5/25¢;
1/10¢ Special 3/25¢ or Special 1 play for 25¢, (large size: 5” x 4”), each
Side Glass for left or right side of dome, for Models R, J and JL, edges are
rounded as original, (add $15.00 for packing & shipping one or both), each
Mechanism cover, molded plastic, with light blue color molded in,
Model R only, medallion not included
Mechanism cover, molded plastic, with yellow color molded in,
Models J/JL only, medallion not included
Mechanism cover, molded plastic, (primed, gray primer), for Models: R,
J/JL, KS/KD, L100/101, 161, 201, 220 & 222, medallions not included
Plastic Medallion for mechanism cover, for Model R only, screen-printed
and mirror-Mylar on back, flat front and back, includes attachment hardware
Plastic Medallion for mechanism cover, for Models J & JL, screen-printed
and mirror-Mylar on back, flat front and back, includes attachment hardware
Barrel screw, holds left side of Mech. cover at correct height, for Seeburg
Models: R, J, JL, KS/KD200, L100, 101, 161, 201, 220 & 222, slotted head
Barrel screw, holds left side of Mech. cover at correct height, for Seeburg
Models: R, J, JL, KS/KD200, L100, 101, 161, 201, 220 & 222, Phillips head
- 28 -
$40.00
29.00
59.00
275.00
10.00
10.00
10.00
9.00
45.00
150.00
150.00
125.00
80.00
80.00
7.00
9.00
SEEBURG HF100R of 1954 – 1955 and
100J & 100JL of 1955 – 1957 (Continued)
A-1 PART #
77-007 Program glass, for models: G, W, R, J & JL, (letters & numbers are baked on,
Exact, original, font & color, all edges of glass are sanded), 5 piece set
$45.00
77-008 Program glass, for models: G, W, R, J & JL, single pieces, (letters & #s are
baked on, original font & color: A1/B1, C1/D1, E1/F1, G1/H1 or J1/K1), each
12.50
64-010 Sponge rubber gasket, for program glass, $0.90 per foot or one piece, (40”)
3.00
77-009
77-065
77-010
77-067
Instruction glass, 3 colors, 2 pc. set, “6 PLAYS QUARTER”, Original Maroon color
Instruction glass, 3 colors, 2 pc. set, “6 PLAYS QUARTER”, Popular Red color
Instruction glass, 3 colors, 2 pc. set, “3 PLAYS QUARTER”, Original Maroon color
Instruction glass, 3 colors, 2 pc. set, “3 PLAYS QUARTER”, Popular Red color
16.00
16.00
16.00
16.00
77-011 Instruction glass, 3 colors, 2 pc. set, “25¢ PER SELECTN.”, Original Maroon color
16.00
68-012 Speed washers, hold instruction glass in place, 10 pieces
78-006 Latch bar solenoid for Electrical Selector, all metal frame, as original
78-020 Free play adapter, plugs in to existing credit unit, has switch for free play
or coin operation, eliminates latch bar solenoid burn-out, for Seeburg
Models: A, B, BL, C, G, W, R, J and JL, (This item is not discountable)
77-050 Select glass, Seeburg G, W, R, J, JL, L100 and 101, green
77-051 Select glass, Seeburg G, W, R, J, JL, L100 and 101, blue
68-015 Coin reject plunger, plated, with scavenger wire, (Models G thru APFEAI)
Specify # Title headings for Seeburg program holders, Specify: a color and the
A-1 part # from the list at the top of page 15, (11 or 12 piece assortment)
20-019 Rivets, plastic, original color, 2 parts, for upper interior trim, Model R, 50 pcs.
20-022 Rivets, plastic, original color, 2 parts, for interior trim, Models J & JL, 10 pcs.
83-004 Plastic Stripper plate (clear), complete with 2 stylus-cleaning brushes,
brush holders, and 6 screws, (all stainless steel hardware)
83-001 Plastic Stripper plate (clear), (with 6 stainless steel screws only)
83-002 Brush holders, hold stylus-cleaning brushes, (stainless steel), per pair
83-003 Brushes, stylus-cleaning, for plastic stripper plate, per pair
83-035 Stylus brush, Seeburg #405219, used to manually clean the styli
& the brushes on the stripper plate, (Pictured on page 1219 in the manual)
84-015 Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
84-001 Motor coupler, connects mech. motor to gear, (replace if rubber is hard)
84-002 Motor support plug, rubber, for under mechanism motor
84-003 Mechanism turntable drive bushings, Seeburg part # 245464, pair
84-004 Mechanism frame rubber bumper, Seeburg part # 245291, pair
84-005 Rubber cushion strips, (records rest on these while in the magazine),
front is square, Seeburg #245334, rear is round, #245468, per pair
84-020 Selector Coil & Armature Assembly, (a/k/a: Pin Bank), (Completely
dissembled & rebuilt), Specify: M100B/BL, M100C, HF100G, W100,
HF100R, 100J or 100JL, see page 64 for more information, each
74-009 Styli for original Pickering/Seeburg redhead cartridge, (.7 mil
diamond tip for all stereo and mono. records), per pair
83-007 Springs for tone arm, hand made in the U.S.A., exact replacements, pair
78-010 Trip switch, Micro, for tone arm, (for Models B through APFEAI)
83-010 Balance spring for Micro trip switch, for tone arm, each one is hand made
in the U.S.A., Seeburg part # 245817, (for Models B through APFEAI)
83-011 Spring for mechanism reversing switch, (Models B thru STD4), hand made
78-002 Trip coil for mechanism, Models B thru JL and V without 2050 for trip, ea.
92-015 Capacitor, (run condenser), for mechanism motor, original style/metal can,
for M100A thru STD4, not SX100, for all USA motors, not for Nidec motors
3.50
60.00
- 29 -
68.95
6.50
6.50
25.00
10.00
15.00
3.00
60.00
50.00
12.00
12.00
3.00
25.00
25.00
2.50
5.00
5.00
2.00
195.00
50.00
7.00
20.00
8.00
14.00
25.00
30.00
SEEBURG HF100R of 1954 – 1955 and
100J & 100JL of 1955 – 1957 (Continued)
A-1 PART #
83-009
78-001
78-031
20-002
20-003
20-004
20-005
73-035
68-010
73-039
68-011
73-036
73-037
73-038
73-040
20-007
20-008
20-009
20-010
89-001
65-002
65-015
20-011
20-012
20-013
20-014
20-015
20-030
20-017
20-018
20-021
76-007
67-004
67-012
Carriage roller for mechanism, Seeburg part # 245082, each
Cancel coil for Selector pin bank, Seeburg B/JL, (sleeve included, no plunger), ea.
Plunger & spring for cancel coil, for Selector pin bank, (two piece set), each
Mech. plastic end cap, blue "100" for Model R, (L.H. & R.H., same item),
(This item is out of stock at this time), each
Mech. plastic end caps, blue "100" for Model R, (Out of stock at this time), pr.
Mech. plastic end cap. red "100" for Models J & JL, (L.H. or R.H., same item),
(This item is out of stock at this time), each
Mech. plastic end caps, red "100" for J & JL, (Out of stock at this time), pair
Selection playing plastic, indicates letter and number of record playing, dark
blue letters & numbers w/white background, Models G, W, & R, (A1 thru K0)
Rivets, chrome plated, for selection playing plastic, (for Models B,
BL, C, G, W, R, J & VL200), 15 pcs.
Selection playing plastic, indicates letter and number of record playing,
red letters & numbers w/white background, Models J and JL only, (A1 thru K0)
Rivets, brass, for selection playing plastic, (Models JL & V200 only), 15 pcs.
Letter and number strip for record magazine, adhesive backed,
(for Models B, BL, C, G, W, R, J & JL), Specify: dark blue, aqua or red
Letter and number strips for popularity meter, adhesive backed
(for Models B, BL, C, G, W, R, J & JL), Specify: dark blue, aqua or red
Letter and number strip for selector coil frame, (pin cage), adhesive backed,
(for Models B, BL, C, G, W, R, J & JL), dark blue, (original color)
Letter and number strips for record magazine, popularity meter & pin cage,
(Models B, through JL), Specify: dark blue, aqua or red, complete 3 pc. set
Frosted diffuser glass, 32” X 4 ¼”, for behind program title board
Diffuser above grill, original shape and color, (blue), for HF100R only
Diffuser above grill, original shape, multi-colored, printed, for 100-J only
Diffuser above grill, original shape, multi-colored, printed, for 100-JL only
Interior labels, (lubrication diagram, etc., Models B, BL, C, G, W, R, J & JL)
Grill cloth, gold is suggested for Model HF100R, other colors are listed
on page 74 under GRILL CLOTH, cloth size 30” X 40”, each
Speaker-board screen, (used in back of front metal grill screen), plastic fiber,
charcoal-black, for Seeburg Models 100J thru DS160, 36” X 30”
Grill ornaments, (“waterfalls”/“lightening bolts”), for Model R only,
die cast METAL castings, chrome plated, as original, ready to install,
Specify: on the right side of the glass or on the left side of the glass, each
Grill ornaments, (“waterfalls”/“lightening bolts”), for Model R only,
die cast METAL castings, chrome plated, as original, ready to install,
3 left sides and 3 right sides, complete 6 pc. set, (no additional discount)
Grill glass, fluted, (all sharp edges have been sanded for safety),
(add $18.00 for special packaging and shipping), complete 5 piece set
Grill glass, fluted, single piece, (all sharp edges have been sanded), each
Grill frame, (for fluted grill glass), polished stainless steel, each
Grill frames, (for fluted grill glass), polished stainless steel, 5 piece set
Kick plate, Stainless steel, front, Model R only
Foot trim strips, Stainless steel, left & right sides, Model R only, per pair
Kick plate, Stainless steel, front, Models J and JL only
Key for cabinet sides and back door, (not cash door), F279
Cash bag, (duck cloth, as original, hand made in the U.S.A.)
Cash door, superior grade birch covered plywood, with backup plates,
(for use with metal frame around opening, Models C through LS3)
- 30 -
$6.00
27.50
12.00
110.00
200.00
110.00
200.00
9.00
4.00
9.00
8.00
5.00
5.00
5.00
15.00
25.00
32.50
38.00
38.00
8.00
16.00
14.00
89.00
495.00
160.00
35.00
20.00
85.00
38.50
45.00
42.50
7.00
12.00
18.00
SEEBURG HF100R of 1954 – 1955 and
100J & 100JL of 1955 – 1957 (Continued)
A-1 PART #
76-050 Lock, 1 1/8” quality lock, & 2 keys for Reproduction - wooden cash door
76-051 Lock, 1 1/8” quality lock, hardware, & 2 keys for Original metal cash door
76-054 Lock, 1 1/8” quality lock, & 2 keys for lower back door,
(rotates one-half turn and key is removable in locked and open positions)
81-006 I.D. plate, Model R, (as original), no serial number, for back of cabinet
81-007 I.D. plate, Model J, (as original), no serial number, for back of cabinet
81-008 I.D. plate, Model JL, (as original), no serial number, for back of cabinet
67-008 Lower back door U-wood frame, (this item does not include any metal parts
that were included with the original frame), (+ $10.00 for pack. & shipping)
67-009 Masonite amp & receiver cover, (fits into lower back door U-wood frame)
68-002 Safety chain for Lower back door, w/chain cover, mounting screw & key clip
68-026 Screws, hold Amp. & Receiver on lower back door, (4) 1”, (4) ½”, 65¢ ea. or 8 pcs.
66-002 Decals, water transfer, for lower back door, (On/Off & Vol. Control), 2 pc. set
66-005 Decals, Vinyl, peel & stick, for lower back door, (On/Off & Vol. Control), 2 pc. set
92-038 Capacitor kit for Seeburg Models R, J & JL, using Amp. # MRA5-L6
includes schematics & replacement values reference sheet, ea.
92-039 Capacitor kit for Seeburg’s: J, JL, V & VL200, using Amplifier #: HFMA1-L6
includes schematics & replacement values reference sheet
81-035 I.D. plate for HFMA1-L6, (High Fidelity Master Amplifier), not discountable
92-052 Capacitor kit for WSR7-L6, Selection Receiver, includes: schematics and
replacement values reference sheet, (does not include cap. for wallboxes)
92-025 Capacitor for Stepper, operates wallboxes in Seeburgs: M100A thru LPC480
37-009 Fuse, 3 amp or 3 2/10 amp Fustat, large screw in type, for Seeburg: M100A
thru VL200 Selection Receivers, (these are for the operation of wallboxes)
91-003 Volume control pot. for Models 146, 147, 148, A, B/BL, C, G, W & R
91-004 Volume control pot. Models J/JL, V/VL, KS/KD, L100/101, Q & AY (mono.)
76-001 Volume control key for original pots., (Seeburg amps. thru SHFA2 & all Wurlitzer’s)
72-003 Bulb, miniature #44 (selection indicator lamps) (2 required), each
72-004 Bulb, miniature #47 (behind credit glass) (2 required), each
72-011 Bulb, miniature #81 (behind mechanism plastic end cap “100”) (2 required), each
70-011 Fluorescent lamp 25 watt 33" T12, daylight, recommended color (1)
70-010 Fluorescent lamp 25 watt 33" T12, cool white, optional color
70-050 Colored sleeve for T12 fluorescent lamp, (cut to your specified length),
Specify: sleeve color: red, blue, green, yellow or pink, per foot
71-006 Ballast, 25 watt, for 1 lamp, new style, (clamped core), made in the U.S.A.
71-035 Ballast, 25 watt, for 1 lamp, original style case & Black color, (Now thermally
protected), made in the U.S.A., includes 2 rubber grommets for mounting
71-028 Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
71-030 Outlet, 3-wire grounded duplex receptacle, (The Receiver plugs into this)
68-004 Caster sockets, use with original Seeburg metal casters or our 2 ½” hard
rubber replacement casters, (made by original supplier to Seeburg), each
68-005 Casters 2 ½” hard rubber, (made by original supplier to Seeburg), each
$10.00
10.00
10.00
15.00
15.00
15.00
45.00
45.00
10.00
5.00
10.00
8.00
65.00
65.00
22.50
27.50
12.00
8.00
30.00
30.00
3.00
1.00
1.00
2.00
10.00
10.00
1.75
12.00
20.00
1.50
12.00
8.00
3.00
7.00
SEEBURG V200 of 1955 – 1956 and VL200 of 1956 – 1957
100 Records (200 Selections)
A-1 PART #
80-035
80-036
80-037
21-001
Service & parts manual, Seeburg V200 & VL200, 188 pages, order R-263
Installation, Operation & Troubleshooting, V & VL, 56 pages, order R-427
Seeburg V & VL, Purchase R-263 and R-427, save $10.00, order R-263A
Dome glass, with printed logo, (add $40 for packaging & shipping)
- 31 -
$40.00
29.00
59.00
325.00
SEEBURG V200 of 1955 – 1956 and VL200 of 1956 – 1957 (Continued)
A-1 PART #
66-001 Cloud-shaped pricing decals, water transfer to inside of glass, 5 to choose
from, Specify: 1/5¢ Special 6/25¢; 2/10¢ Special 6/25¢; 2/10¢ Special 5/25¢;
1/10¢ Special 3/25¢ or Special 1 play for 25¢, (large size: 5” x 4”), each
21-002 Side Glass for left or right side of dome, for V200 and VL200, edges are
rounded, (+ $20.00 for shipping one or both because box is oversize), each
69-005 Mechanism cover, molded plastic, original Gray color molded in, for
Model V200 only, medallion not included, (This item is not discountable)
69-006 Mechanism cover, molded plastic, original Salmon/Pink color molded in, for
Model VL200 only, medallion not included, (This item is not discountable)
21-009 Instruction glass, left, (TO VIEW ENTIRE PROGRAM…), (for V &VL200)
68-012 Speed washers, hold instruction glass in place, 10 pieces
21-010 Coins and Instruction glass, right, (make 5¢ selection only) (for V/VL)
21-011 Coins and Instruction glass, right, (make 10¢ selection only) (for V/VL)
21-012 Credit glass right (small, red, 5¢, ANOTHER COIN REQUIRED) (for V/VL)
81-030 Coin entry instruction plate, etched metal, printed, (NICKELS, DIMES, ETC.)
78-005 Latch bar solenoid for Electrical Selector, all metal frame, as original
68-015 Coin reject plunger, plated, with scavenger wire, (Models G thru APFEAI)
73-009 Lens for button heading, located above selector switch arrow (5), each
73-010 Lenses for button heading, located above selector switch arrow, 5 piece set
21-005 200 Selection glass, for light bar, for V-200 only, (red & white)
21-006 200 Selection glass, for light bar, for VL-200 only, (gold & white)
73-105 V, VL, KS & KD200 Drum classification picture card, with title heading,
Red Hit Tunes (Drummer), 2 piece set
73-106 V, VL, KS & KD200 Drum classification picture card, with title heading,
Red, Hit Tunes (Lady singer), 2 piece set
73-107 V, VL, KS & KD200 Drum classification picture card, with title heading,
Plum, Rhythm and Blues (Trumpet player), 2 piece set
73-108 V, VL, KS & KD200 Drum classification picture card, with title heading,
Plum, Rhythm and Blues (Dancing couple), 2 piece set
73-109 V, VL, KS & KD200 Drum classification picture card, with title heading,
Orange, Country & Western (Cowboy playing guitar), 2 piece set
73-110 V, VL, KS & KD200 Drum classification picture card, with title heading,
Orange, Folk & Western (Cowboy playing guitar), 2 piece set
73-111 V, VL, KS & KD200 Drum classification picture card, with title heading,
Green, All Time Favorites (Lady & umbrella), 2 piece set
73-112 V, VL, KS & KD200 Drum classification picture card, with title heading,
Green, All Time Favorites (Lady, records & console record player), 2 pc. set
73-113 V, VL, KS & KD200 Drum classification picture card, with title heading,
Green, EP Albums, All Time Favorites (Lady, records & console), 2 pc. set
73-114 V, VL, KS & KD200 Drum classification picture card, with title heading,
Blue, Classics & Varieties (Pillar and Piano lid), 2 piece set
73-115 V, VL, KS & KD200 Drum classification picture card, with title heading,
Blue, Classics & Varieties (Orchestra conductor), 2 piece set
73-116 V, VL, KS & KD200 Drum classification picture card, with title heading,
Blue, Jazz (Saxophone player and musical notes), 2 piece set
73-117 V, VL, KS & KD200 Drum classification picture card, with title heading,
Red, White & Blue, Singles, Hit Tunes, Singles (2 trombones), 2 piece set
73-118 V, VL, KS & KD200 Drum classification picture card, with title heading,
Red, White & Blue, Singles, Hit Tunes, Albums (2 trombones), 2 piece set
73-119 V, VL, KS & KD200 Drum classification picture card, with title heading,
Red, White & Blue, Singles, R. and B., Singles (Street lamp), 2 piece set
- 32 -
$9.00
45.00
175.00
175.00
15.00
3.50
15.00
15.00
8.00
12.00
60.00
25.00
12.00
55.00
15.00
15.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
SEEBURG V200 of 1955 – 1956 and VL200 of 1956 – 1957 (Continued)
A-1 PART #
73-120 V, VL, KS & KD200 Drum classification picture card, with title heading,
Red, White & Blue, Singles, R. and B., Albums (Street lamp), 2 piece set
73-121 V, VL, KS & KD200 Drum classification picture card, with title heading,
Red, White & Blue, Singles, Jazz, Singles (3 Trumpet valves), 2 piece set
73-122 V, VL, KS & KD200 Drum classification picture card, with title heading,
Red, White & Blue, Singles, Jazz, Albums (3 Trumpet valves), 2 piece set
73-125 V, VL, KS & KD200 Drum classification picture cards (5 pieces),
with title headings (5 pieces), Specify: any 5 two-piece sets, 10 pieces in all
73-130 V, VL, KS & KD200 Price inserts for program drum, Blue & White Arrow,
5¢ Per Selection, 6 singles – Quarter, (5 left & 5 right), 10 piece set
73-131 V, VL, KS & KD200 Price inserts for program drum, Blue & White Arrow,
10¢ Per Selection, 3 singles – Quarter, (5 left & 5 right), 10 piece set
73-132 V, VL, KS & KD200 Price inserts for program drum, Red & White Arrow
10¢ Two Tunes, Per EP Selection, 3 EPs – Quarter, (5 L. H & 5 R. H.), 10 pcs.
73-133 V, VL, KS & KD200 Price inserts for program drum, Red & White Arrow,
15¢ Two Tunes, EP Selection, 2 For Quarter, (5 left & 5 right), 10 piece set
73-134 V, VL, KS & KD200 Price inserts for program drum, Blue Arrow on White,
10¢ Single Tune per selection, 3 Singles - Quarter, (5 left & 5 right), 10 pieces
73-135 V, VL, KS & KD200 Price inserts for program drum, Blue Arrow on White,
10¢ per Select., 3 Singles - Qtr, 7 Singles - Half Dollar, (5 L & 5 R), 10 pieces
73-136 V, VL, KS & KD200 Price inserts for program drum, Red Arrow on White,
15¢ per EP, 2 EPs - Qtr, 4 EPs & 1 Single - Half Dollar, (5 L & 5 R), 10 pieces
73-137 V, VL, KS & KD200 Price inserts for program drum, Blue script on White,
10¢ per Selection, 4 For Quarter, (All 10 are the same), 10 piece set
73-138 V, VL, KS & KD200 Price inserts for program drum, Blue script on White,
10¢ per Selection, 3 For Quarter, (All 10 are the same), 10 piece set
73-140 V, VL, KS & KD200 Price insert for program drum, choose any one piece,
Specify: Arrow or Script, Color and pricing, each piece
73-011 Drum letter & number strips: A1, B1, C1, 20 piece set
83-020 Plastic Stripper plate (green), complete with 2 stylus-cleaning brushes,
brush holders, and 6 screws, (all stainless steel hardware)
83-021 Stripper plate (green), (with 6 stainless steel screws only)
83-002 Brush holders, hold stylus-cleaning brushes, (stainless steel), per pair
83-003 Brushes, stylus-cleaning, for plastic stripper plate, per pair
83-035 Stylus brush, Seeburg #405219, used to manually clean the styli
& the brushes on the stripper plate, (See pages 14 & 16 in the manual)
84-015 Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
84-001 Motor coupler, connects mech. motor to gear, (replace if rubber is hard)
84-002 Motor support plug, rubber, for under mechanism motor
84-003 Mechanism turntable drive bushings, Seeburg part # 245464, pair
84-004 Mechanism frame rubber bumper, Seeburg part # 245291, pair
74-009 Styli for original Pickering/Seeburg redhead cartridge, (.7 mil
diamond tip for all stereo and mono. records), per pair
83-007 Springs for tone arm, hand made in the U.S.A., exact replacements, pair
78-010 Trip switch, Micro, for tone arm, (for Models B through APFEAI)
83-010 Balance spring for Micro trip switch, for tone arm, each one is hand made
in the U.S.A., Seeburg part # 245817, (for Models B through APFEAI)
83-011 Spring for mechanism reversing switch, (Models B thru STD4), hand made
78-002 Trip coil for mechanism, Models B thru JL and V without 2050 for trip, ea.
78-003 Trip coil for mechanism, Models V with 2050 for trip through DS, each
- 33 -
$6.00
6.00
6.00
25.00
20.00
20.00
20.00
20.00
20.00
20.00
20.00
20.00
20.00
2.50
22.50
60.00
50.00
12.00
12.00
3.00
25.00
25.00
2.50
5.00
5.00
50.00
7.00
20.00
8.00
14.00
25.00
25.00
SEEBURG V200 of 1955 – 1956 and VL200 of 1956 – 1957 (Continued)
A-1 PART #
92-015 Capacitor, (run condenser), for mechanism motor, original style/metal can,
for M100A thru STD4, not SX100, for all USA motors, not for Nidec motors
78-023 Free Play Credit Unit, completely bypasses the original credit unit, for
Seeburg Model V200 with TSR1 receiver only, (This item not discountable)
78-022 Free Play Credit Unit, completely bypasses the original credit unit, for
Seeburg Models: V200 with TSR3 receiver, VL200, KS & KD200, 161, 201,
220, 222, AY100, AY160, DS100 and DS160, (This item not discountable)
83-009 Carriage roller for mechanism, Seeburg part # 245082, each
68-010 Rivets, chrome plated, for selection playing plastic, (for Models B,
BL, C, G, W, R, J & VL200), 15 pcs.
73-143 Selection playing plastic, 1-pc., indicates letter & number of record playing,
black letters & numbers on white background, (A1 thru V0), without holes
68-011 Rivets, brass, for selection playing plastic, (Models JL & V200 only), 15 pcs.
73-142 Selection playing plastic, 1-pc., indicates letter & number of record playing,
red letters & numbers on white background, (A1 thru V0), holes are punched
21-003 Diffuser above grill, original shape, multi-colored, printed, for Model V-200 only
21-004 Diffuser above grill, original shape, multi-colored, printed, Model VL-200 only
21-007 Side window, plastic, round, convex, “Seeburg”, (green/white), V-200 only, ea.
21-008 Side window, plastic, round, convex, “Seeburg”, (white & tan), VL-200 only, ea.
65-015 Speaker-board screen, (used in back of front metal grill screen), plastic fiber,
charcoal-black, for Seeburg Models 100J thru DS160, 36” X 30”
76-008 Key for cabinet sides and back door, (not cash door), F314
67-004 Cash bag, (duck cloth, as original, hand made in the U.S.A.)
67-012 Cash door, superior grade birch covered plywood, with backup plates,
(for use with metal frame around opening, Models C through LS3)
76-050 Lock, 1 1/8” quality lock, & 2 keys for Reproduction - wooden cash door
76-051 Lock, 1 1/8” quality lock, hardware, & 2 keys for Original metal cash door
76-054 Lock, 1 1/8” quality lock, & 2 keys for lower back door,
(rotates one-half turn and key is removable in locked and open positions)
81-009 I.D. plate, Model V, (as original), no serial number, for back of cabinet
81-010 I.D. plate, Model VL, (as original), no serial number, for back of cabinet
67-008 Lower back door U-wood frame, (this item does not include any metal parts
that were included with the original frame), (+ $10.00 for pack. & shipping)
67-009 Masonite amp & receiver cover, (fits into lower back door U-wood frame)
68-002 Safety chain for Lower back door, w/chain cover, mounting screw & key clip
68-026 Screws, hold Amp. & Receiver on lower back door, (4) 1”, (4) ½”, 65¢ ea. or 8 pcs.
66-002 Decals, water transfer, for lower back door, (On/Off & Vol. Control), 2 pc. set
66-005 Decals, Vinyl, peel & stick, for lower back door, (On/Off & Vol. Control), 2 pc. set
92-039 Capacitor kit for Seeburg’s: J, JL, V & VL200, using Amplifier #: HFMA1-L6
includes schematics & replacement values reference sheet
81-035 I.D. plate for HFMA1-L6, (High Fidelity Master Amplifier), not discountable
92-054 Capacitor kit for TSR1-L6, Tormat Selection Recvr., includes: schematics &
replacement values reference sheet, (does not include cap. for wallboxes)
92-055 Capacitor kit for TSR3-L6, Tormat Selection Recvr., includes: schematics &
replacement values reference sheet, (does not include cap. for wallboxes)
92-025 Capacitor for Stepper, operates wallboxes in Seeburgs: M100A thru LPC480
37-009 Fuse, 3 amp or 3 2/10 amp Fustat, large screw in type, for Seeburg: M100A
thru VL200 Selection Receivers, (these are for the operation of wallboxes)
91-004 Volume control pot. Models J/JL, V/VL, KS/KD, L100/101, Q & AY (mono.)
76-001 Volume control key for original pots., (Seeburg amps. thru SHFA2 & all Wurlitzer’s)
37-014 Plug, two flat prongs, used in TSR1, 2 & 3, (J7 plug for reject switch)
- 34 -
$30.00
94.50
94.50
6.00
4.00
12.00
8.00
12.00
40.00
40.00
25.00
25.00
14.00
7.00
12.00
18.00
10.00
10.00
10.00
15.00
15.00
45.00
45.00
10.00
5.00
10.00
8.00
65.00
22.50
35.00
35.00
12.00
8.00
30.00
3.00
7.00
SEEBURG V200 of 1955 – 1956 and VL200 of 1956 – 1957 (Continued)
A-1 PART #
72-003
72-008
72-010
72-011
70-007
70-006
70-011
70-010
70-050
71-001
71-006
71-035
71-028
71-016
71-030
68-004
68-005
Bulb, miniature #44 (selection indicator lamps) (2 required), each
Bulb, miniature #55 (credit lamps) (3), each
Bulb, miniature #63 (magazine ends “200”) (2), each
Bulb, miniature #81 (5 for button headings 5), (2 for cabinet sides “Seeburg”), each
Fluorescent lamp 20 watt 24” T12, daylight, (program drum) (1)
Fluorescent lamp 20 watt 24” T12, cool white, optional color
Fluorescent lamp 25 watt 33” T12, daylight, recommended color (2), each
Fluorescent lamp 25 Watt 33” T12, cool white, optional color
Colored sleeve for T12 fluorescent lamp, (cut to your specified length),
Specify: sleeve color: red, blue, green, yellow or pink, per foot
Ballast 14 to 20 watt, for 1 lamp, new square style, clamped core, white, each
Ballast, 25 watt, for 1 lamp, new style, (clamped core), made in the U.S.A.
Ballast, 25 watt, for 1 lamp, original style case & Black color, (Now thermally
protected), made in the U.S.A., includes 2 rubber grommets for mounting
Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
Outlet, 3-wire grounded duplex receptacle, (The Receiver plugs into this)
Caster sockets, use with original Seeburg metal casters or our 2 ½” hard
rubber replacement casters, (made by original supplier to Seeburg), each
Casters 2 ½” hard rubber, (made by original supplier to Seeburg), each
$1.00
1.00
1.50
2.00
7.00
7.00
10.00
10.00
1.75
12.00
12.00
20.00
1.50
12.00
8.00
3.00
7.00
SEEBURG KS200 & KD200 of 1957 100 Records (200 Selections)
(KS indicates a single pricing unit,
KD indicates a dual pricing unit)
A-1 PART #
80-034 Select-O-Matic 200 mechanism operation manual, for Seeburg KS200
and KD200 only, 26 pages, order R-48
80-038 Service manual & parts list for KS, KD & L100, 156 pages, order R-277
80-039 Installation, Operation manual & Troubleshooting guide for
Models KS, KD & L100, 60 pages, order R-225
80-040 KS, KD & L100, Purchase R-277 and R-225, Save $10.00, order R-277A
22-003 Lid glass, printed, (add $30 for packaging & shipping)
22-012 Decal, water transfer, for lid glass, HIGH Fidelity & musical note, 2 colors
66-001 Cloud-shaped pricing decals, water transfer to inside of glass, 5 to choose
from, Specify: 1/5¢ Special 6/25¢; 2/10¢ Special 6/25¢; 2/10¢ Special 5/25¢;
1/10¢ Special 3/25¢ or Special 1 play for 25¢, (large size: 5” x 4”), each
22-001 Side glass, printed per pair, (add $20 for packaging & shipping)
22-002 Side glass, printed, left side, (add $20 for packaging & shipping), each
22-007 Side glass, printed, right side, (add $20 for packaging & shipping), each
69-004 Mechanism cover, molded plastic, (primed, gray primer), for Models: R, J/JL,
KS/KD, L100/101, 161, 201, 220 & 222, Logo glass & frame not included
77-052 Glass logo for mech. cover, printed “SEEBURG”, (gold leaf on back side)
68-050 Barrel screw, holds left side of Mech. cover at correct height, for Seeburg
Models: R, J, JL, KS/KD200, L100, 101, 161, 201, 220 & 222, slotted head
68-051 Barrel screw, holds left side of Mech. cover at correct height, for Seeburg
Models: R, J, JL, KS/KD200, L100, 101, 161, 201, 220 & 222, Phillips head
22-005 Instruction glass, left, (TO VIEW ENTIRE PROGRAM…), (for KS & KD200)
22-006 Coins and credit glass, right side , (make 10¢ selection only, etc.)
78-005 Latch bar solenoid for Electrical Selector, all metal frame, as original
68-015 Coin reject plunger, plated, with scavenger wire, (Models G thru APFEAI)
73-009 Lens for button heading, located above selector switch arrow (5), each
73-010 Lenses for button heading, located above selector switch arrow, 5 piece set
- 35 -
$19.50
40.00
29.00
59.00
65.00
10.00
9.00
140.00
75.00
75.00
125.00
50.00
7.00
9.00
15.00
18.00
60.00
25.00
12.00
55.00
SEEBURG KS200 & KD200 of 1957 (Continued)
A-1 PART #
73-105 V, VL, KS & KD200 Drum classification picture card, with title heading,
Red Hit Tunes (Drummer), 2 piece set
73-106 V, VL, KS & KD200 Drum classification picture card, with title heading,
Red, Hit Tunes (Lady singer), 2 piece set
73-107 V, VL, KS & KD200 Drum classification picture card, with title heading,
Plum, Rhythm and Blues (Trumpet player), 2 piece set
73-108 V, VL, KS & KD200 Drum classification picture card, with title heading,
Plum, Rhythm and Blues (Dancing couple), 2 piece set
73-109 V, VL, KS & KD200 Drum classification picture card, with title heading,
Orange, Country & Western (Cowboy playing guitar), 2 piece set
73-110 V, VL, KS & KD200 Drum classification picture card, with title heading,
Orange, Folk & Western (Cowboy playing guitar), 2 piece set
73-111 V, VL, KS & KD200 Drum classification picture card, with title heading,
Green, All Time Favorites (Lady & umbrella), 2 piece set
73-112 V, VL, KS & KD200 Drum classification picture card, with title heading,
Green, All Time Favorites (Lady, records & console record player), 2 pc. set
73-113 V, VL, KS & KD200 Drum classification picture card, with title heading,
Green, EP Albums, All Time Favorites (Lady, records & console), 2 pc. set
73-114 V, VL, KS & KD200 Drum classification picture card, with title heading,
Blue, Classics & Varieties (Pillar and Piano lid), 2 piece set
73-115 V, VL, KS & KD200 Drum classification picture card, with title heading,
Blue, Classics & Varieties (Orchestra conductor), 2 piece set
73-116 V, VL, KS & KD200 Drum classification picture card, with title heading,
Blue, Jazz (Saxophone player and musical notes), 2 piece set
73-117 V, VL, KS & KD200 Drum classification picture card, with title heading,
Red, White & Blue, Singles, Hit Tunes, Singles (2 trombones), 2 piece set
73-118 V, VL, KS & KD200 Drum classification picture card, with title heading,
Red, White & Blue, Singles, Hit Tunes, Albums (2 trombones), 2 piece set
73-119 V, VL, KS & KD200 Drum classification picture card, with title heading,
Red, White & Blue, Singles, R. and B., Singles (Street lamp), 2 piece set
73-120 V, VL, KS & KD200 Drum classification picture card, with title heading,
Red, White & Blue, Singles, R. and B., Albums (Street lamp), 2 piece set
73-121 V, VL, KS & KD200 Drum classification picture card, with title heading,
Red, White & Blue, Singles, Jazz, Singles (3 Trumpet valves), 2 piece set
73-122 V, VL, KS & KD200 Drum classification picture card, with title heading,
Red, White & Blue, Singles, Jazz, Albums (3 Trumpet valves), 2 piece set
73-125 V, VL, KS & KD200 Drum classification picture cards (5 pieces),
with title headings (5 pieces), Specify: any 5 two-piece sets, 10 pieces in all
73-130 V, VL, KS & KD200 Price inserts for program drum, Blue & White Arrow,
5¢ Per Selection, 6 singles – Quarter, (5 left & 5 right), 10 piece set
73-131 V, VL, KS & KD200 Price inserts for program drum, Blue & White Arrow,
10¢ Per Selection, 3 singles – Quarter, (5 left & 5 right), 10 piece set
73-132 V, VL, KS & KD200 Price inserts for program drum, Red & White Arrow
10¢ Two Tunes, Per EP Selection, 3 EPs – Quarter, (5 L. H & 5 R. H.), 10 pcs.
73-133 V, VL, KS & KD200 Price inserts for program drum, Red & White Arrow,
15¢ Two Tunes, EP Selection, 2 For Quarter, (5 left & 5 right), 10 piece set
73-134 V, VL, KS & KD200 Price inserts for program drum, Blue Arrow on White,
10¢ Single Tune per selection, 3 Singles - Quarter, (5 left & 5 right), 10 pieces
73-135 V, VL, KS & KD200 Price inserts for program drum, Blue Arrow on White,
10¢ per Select., 3 Singles - Qtr, 7 Singles - Half Dollar, (5 L & 5 R), 10 pieces
73-136 V, VL, KS & KD200 Price inserts for program drum, Red Arrow on White,
15¢ per EP, 2 EPs - Qtr, 4 EPs & 1 Single - Half Dollar, (5 L & 5 R), 10 pieces
- 36 -
$6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
6.00
25.00
20.00
20.00
20.00
20.00
20.00
20.00
20.00
SEEBURG KS200 & KD200 of 1957 (Continued)
A-1 PART #
73-137 V, VL, KS & KD200 Price inserts for program drum, Blue script on White,
10¢ per Selection, 4 For Quarter, (All 10 are the same), 10 piece set
73-138 V, VL, KS & KD200 Price inserts for program drum, Blue script on White,
10¢ per Selection, 3 For Quarter, (All 10 are the same), 10 piece set
73-140 V, VL, KS & KD200 Price insert for program drum, choose any one piece,
Specify: Arrow or Script, Color and pricing, each piece
73-011 Drum letter & number strips: A1, B1, C1, 20 piece set
83-004 Plastic Stripper plate (clear), complete with 2 stylus-cleaning brushes,
brush holders, and 6 screws, (all stainless steel hardware)
83-001 Plastic Stripper plate (clear), (with 6 stainless steel screws only)
83-002 Brush holders, hold stylus-cleaning brushes, (stainless steel), per pair
83-003 Brushes, stylus-cleaning, for plastic stripper plate, per pair
83-035 Stylus brush, Seeburg #405219, used to manually clean the styli
& the brushes on the stripper plate, (See page 14 of the installation manual)
84-015 Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
84-001 Motor coupler, connects mech. motor to gear, (replace if rubber is hard)
84-002 Motor support plug, rubber, for under mechanism motor
84-003 Mechanism turntable drive bushings, Seeburg part # 245464, pair
84-004 Mechanism frame rubber bumper, Seeburg part # 245291, pair
74-009 Styli for original Pickering/Seeburg redhead cartridge, (.7 mil
diamond tip for all stereo and mono. records), per pair
83-007 Springs for tone arm, hand made in the U.S.A., exact replacements, pair
78-010 Trip switch, Micro, for tone arm, (for Models B through APFEAI)
83-010 Balance spring for Micro trip switch, for tone arm, each one is hand made
in the U.S.A., Seeburg part # 245817, (for Models B through APFEAI)
83-011 Spring for mechanism reversing switch, (Models B thru STD4), hand made
78-003 Trip coil for mechanism, Models V with 2050 for trip through DS, each
92-015 Capacitor, (run condenser), for mechanism motor, original style/metal can,
for M100A thru STD4, not SX100, for all USA motors, not for Nidec motors
78-022 Free Play Credit Unit, completely bypasses the original credit unit, for
Seeburg Models: V200 with TSR3 receiver, VL200, KS & KD200, 161, 201,
220, 222, AY100, AY160, DS100 and DS160, (This item not discountable)
83-009 Carriage roller for mechanism, Seeburg part # 245082, each
22-008 200 Select-0-Matic, round, printed glass, for mechanism ends, each
68-009 Rivets and back-up washers, chrome plated, for selection playing plastic,
(for Models KS/KD through 222), 15 rivets & 15 washers
73-143 Selection playing plastic, 1-pc., indicates letter & number of record playing,
black letters & numbers on white background, (A1 thru V0), without holes
73-142 Selection playing plastic, 1-pc., indicates letter & number of record playing,
red letters & numbers on white background, (A1 thru V0), holes are punched
22-004 Diffuser above grill, original shape, original blue & clear pattern, printed
65-015 Speaker-board screen, (used in back of front metal grill screen), plastic fiber,
charcoal-black, for Seeburg Models 100J thru DS160, 36” X 30”
76-009 Key for cabinet sides and back door, (not cash door), F313
67-004 Cash bag, (duck cloth, as original, hand made in the U.S.A.)
67-012 Cash door, superior grade birch covered plywood, with backup plates,
(for use with metal frame around opening, Models C through LS3)
76-050 Lock, 1 1/8” quality lock, & 2 keys for Reproduction - wooden cash door
76-051 Lock, 1 1/8” quality lock, hardware, & 2 keys for Original metal cash door
76-058 Lock, 1 1/8” quality lock, hardware & 2 keys for lower back door
- 37 -
$20.00
20.00
2.50
22.50
60.00
50.00
12.00
12.00
3.00
25.00
25.00
2.50
5.00
5.00
50.00
7.00
20.00
8.00
14.00
25.00
30.00
94.50
6.00
22.50
5.00
12.00
12.00
25.00
14.00
7.00
12.00
18.00
10.00
10.00
15.00
SEEBURG KS200 & KD200 of 1957 (Continued)
A-1 PART #
81-011 I.D. plate for Models KD & KS are the same,
(as original), no serial number, for back of cabinet
95-001 Graphics for rear door, Blue, vinyl transfer, (Models KS200 & KD200 only),
“MASTER VOLUME CONTROL” & “MAIN SWITCH”, “RECORD REJECT”, per pr.
92-041 Capacitor kit: Seeburg Models KS & KD200 and L100, Amp. #: 25PAU-1,
includes schematics & replacement values reference sheet
93-001 Printed circuit board, PAU for amplifier, (For Models KS, KD & L 100 only)
92-057 Capacitor kit for TEU1, Tormat Electronic Unit, Seeburg Models:
KS KD200 and L100, includes schematic & replacement reference sheet
93-002 Printed circuit board, TEU for receiver, (For Models KS, KD & L 100 only)
91-004 Volume control pot. Models J/JL, V/VL, KS/KD, L100/101, Q & AY (mono.)
76-001 Volume control key for original pots., (Seeburg amps. thru SHFA2 & all Wurlitzer’s)
90-061 Tube socket / connector socket, 7 pin ceramic pc mount for pc boards in
Seeburg Models KS200, KD200 and L100, each
90-062 Tube socket, 8 pin octal ceramic pc mount for holding 5U4, 6L6 & 2050
tubes in pc boards in Seeburg Models KS200, KD200 and L100, each
90-063 Tube socket / connector socket, 9 pin ceramic pc mount for pc boards in
Seeburg Models KS200, KD200 and L100, each
72-001 Bulb, miniature #12 (selection playing indicator) (1)
72-008 Bulb, miniature #55 (credit) (3), (grill ornaments) (3), each
72-011 Bulb, miniature #81 (5 for classification headings), each
72-015 Bulb, miniature #455 (flasher for grill ornaments) (3, optional), each
70-006 Fluorescent lamp 20 watt 24" T12, cool white is recommended (1)
70-010 Fluorescent lamp 25 watt 33" T12, cool white is recommended (2), each
70-050 Colored sleeve for T12 fluorescent lamp, (cut to your specified length),
Specify: sleeve color: red, blue, green, yellow or pink, per foot
71-006 Ballast, 25 watt, for 1 lamp, new style, (clamped core), made in the U.S.A.
71-035 Ballast, 25 watt, for 1 lamp, original style case & Black color, (Now thermally
protected), made in the U.S.A., includes 2 rubber grommets for mounting
71-028 Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
71-030 Outlet, 3-wire grounded duplex receptacle, (The Receiver plugs into this)
68-004 Caster sockets, use with original Seeburg metal casters or our 2 ½” hard
rubber replacement casters, (made by original supplier to Seeburg), each
68-005 Casters 2 ½” hard rubber, (made by original supplier to Seeburg), each
$15.00
12.00
65.00
50.00
35.00
50.00
30.00
3.00
5.00
5.00
5.00
3.00
1.00
2.00
2.00
7.00
10.00
1.75
12.00
20.00
1.50
12.00
8.00
3.00
7.00
SEEBURG L100 of 1957 and
101 (Sometimes referred to as the L101) of 1958
50 Records (100 Selections)
A-1 PART #
80-038 Service manual & parts list for KS, KD & L100, 156 pages, order R-277
80-039 Installation, Operation manual & Troubleshooting guide for
Models KS, KD & L100, 60 pages, order R-225
80-040 KS, KD & L100, Purchase R-277 and R-225, Save $10.00, order R-277A
80-041 Illustrated parts catalog for Model L100 only, 42 pages, order R-1
80-042 KS, KD & L100, purchase R-277, R-225 and R-1, save $23.00, order R-1A
80-043 Service manual & parts list for 101, 161 & 201, 128 pages, order R-278
80-044 Installation, Operate manual & Trouble Shooting guide for Models
101, 161 & 201, 90 pages, order R-111
80-045 Seeburg 101, 161 & 201, purchase R-278 & R-111, save $9.00, order R-278A
80-046 Illustrated parts catalog for Model 101 only, 38 pages, order R-6
80-047 101, 161 & 201, purchase R-278, R-111 and R-6, save $24.00, order R-6A
- 38 -
$40.00
29.00
59.00
26.00
72.00
38.00
36.00
65.00
27.00
77.00
SEEBURG L100 of 1957 and 101
(Sometimes referred to as the L101) of 1958 (Continued)
A-1 PART #
23-005 Lid glass, L100 & 101, printed, (add $30 for packaging & shipping)
66-001 Cloud-shaped pricing decals, water transfer to inside of glass, 5 to choose
from, Specify: 1/5¢ Special 6/25¢; 2/10¢ Special 6/25¢; 2/10¢ Special 5/25¢;
1/10¢ Special 3/25¢ or Special 1 play for 25¢, (large size: 5” x 4”), each
23-001 Side glass, L100 only, printed, per pair, (add $20 for pack. & ship.)
23-002 Side glass, L100 only, printed, left side, (add $20 for pack. & ship.), each
23-006 Side glass, L100 only, printed, right side, (add $20 for pack. & ship.), each
23-003 Side glass, L101 only, printed, per pair, (add $20 for packaging & shipping)
23-004 Side glass, L101 only, printed, left side, (add $20 for pack. & ship.), each
23-012 Side glass, L101 only, printed, right side, (add $20 for pack. & ship.), each
69-004 Mechanism cover, molded plastic, (primed, gray primer), for Models: R, J/JL,
KS/KD, L100/101, 161, 201, 220 & 222, Logo glass & frame not included
77-052 Glass logo for mech. cover, printed “SEEBURG”, (gold leaf on back side)
68-050 Barrel screw, holds left side of Mech. cover at correct height, for Seeburg
Models: R, J, JL, KS/KD200, L100, 101, 161, 201, 220 & 222, slotted head
68-051 Barrel screw, holds left side of Mech. cover at correct height, for Seeburg
Models: R, J, JL, KS/KD200, L100, 101, 161, 201, 220 & 222, Phillips head
23-008 Program title glass, printed, (A1, A2, etc.), L 100 and 101 only
23-009 Instruction glass, left, (PRESS ONE LETTER KEY AND ONE NUMBER KEY)
23-010 Instruction glass, right, (3 PLAYS QUARTER – SELECT AFTER EACH COIN)
78-005 Latch bar solenoid for Electrical Selector, all metal frame, as original
77-050 Select glass, Seeburg G, W, R, J, JL, L100 and 101, green
77-051 Select glass, Seeburg G, W, R, J, JL, L100 and 101, blue
68-015 Coin reject plunger, plated, with scavenger wire, (Models G thru APFEAI)
Specify # Title headings for Seeburg program holders, Specify: a color and the
A-1 part # from the list at the top of page 15, (11 or 12 piece assortment)
83-004 Plastic Stripper plate (clear), complete with 2 stylus-cleaning brushes,
brush holders, and 6 screws, (all stainless steel hardware)
83-001 Plastic Stripper plate (clear), (with 6 stainless steel screws only)
83-002 Brush holders, hold stylus-cleaning brushes, (stainless steel), per pair
83-003 Brushes, stylus-cleaning, for plastic stripper plate, per pair
83-035 Stylus brush, Seeburg #405219, used to manually clean the styli
& the brushes on the stripper plate, (See page 14 of the installation manual)
84-015 Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
84-001 Motor coupler, connects mech. motor to gear, (replace if rubber is hard)
84-002 Motor support plug, rubber, for under mechanism motor
84-003 Mechanism turntable drive bushings, Seeburg part # 245464, pair
84-004 Mechanism frame rubber bumper, Seeburg part # 245291, pair
74-009 Styli for original Pickering/Seeburg redhead cartridge, (.7 mil
diamond tip for all stereo and mono. records), per pair
83-007 Springs for tone arm, hand made in the U.S.A., exact replacements, pair
78-010 Trip switch, Micro, for tone arm, (for Models B through APFEAI)
83-010 Balance spring for Micro trip switch, for tone arm, each one is hand made
in the U.S.A., Seeburg part # 245817, (for Models B through APFEAI)
83-011 Spring for mechanism reversing switch, (Models B thru STD4), hand made
78-003 Trip coil for mechanism, Models V with 2050 for trip through DS, each
92-015 Capacitor, (run condenser), for mechanism motor, original style/metal can,
for M100A thru STD4, not SX100, for all USA motors, not for Nidec motors
- 39 -
$65.00
9.00
130.00
70.00
70.00
130.00
70.00
70.00
125.00
50.00
7.00
9.00
40.00
12.00
12.00
60.00
6.50
6.50
25.00
10.00
60.00
50.00
12.00
12.00
3.00
25.00
25.00
2.50
5.00
5.00
50.00
7.00
20.00
8.00
14.00
25.00
30.00
SEEBURG L100 of 1957 and 101
(Sometimes referred to as the L101) of 1958 (Continued)
A-1 PART #
78-024 Free Play Credit Unit, completely bypasses the original credit unit, for
Seeburg Models: L100, 101, Q100 & Q160, (This item is not discountable)
83-009 Carriage roller for mechanism, Seeburg part # 245082, each
23-011 100 Select-0-Matic glass, round, for mechanism ends, each
68-009 Rivets and back-up washers, chrome plated, for selection playing plastic,
(for Models KS/KD through 222), 15 rivets & 15 washers
23-007 Diffuser above grill, model L100, original shape and multi-colored, printed
pattern: Red, Blue, Green and Orange, (can also be used on model 101)
65-015 Speaker-board screen, (used in back of front metal grill screen), plastic fiber,
charcoal-black, for Seeburg Models 100J thru DS160, 36” X 30”
76-009 Key for cabinet sides and back door, (not cash door), F313
67-004 Cash bag, (duck cloth, as original, hand made in the U.S.A.)
67-012 Cash door, superior grade birch covered plywood, with backup plates,
(for use with metal frame around opening, Models C through LS3)
76-050 Lock, 1 1/8” quality lock, & 2 keys for Reproduction - wooden cash door
76-051 Lock, 1 1/8” quality lock, hardware, & 2 keys for Original metal cash door
76-058 Lock, 1 1/8” quality lock, hardware & 2 keys for lower back door
95-002 Graphics for rear upper cabinet, BLUE, vinyl transfer, (for Models L100,
101, 161, and 201), “SEEBURG SELECT-O-MATIC”
95-003 Graphics for rear door, BLUE, vinyl transfer, (Models L100, 101, 161, 201, 220
& 222), “MASTER VOLUME CONTROL” & “MAIN SWITCH”, “RECORD REJECT”
92-041 Capacitor kit: Seeburg Models KS & KD200 and L100, Amp. #: 25PAU-1,
includes schematics & replacement values reference sheet
93-001 Printed circuit board, PAU for amplifier, (For Models KS, KD & L 100 only)
92-057 Capacitor kit for TEU1, Tormat Electronic Unit, Seeburg Models:
KS KD200 and L100, includes schematic & replacement reference sheet
93-002 Printed circuit board, TEU for receiver, (For Models KS, KD & L 100 only)
92-040 Capacitor kit: Seeburg Models 101, 161 and 201 using Amplifier #: HFMA2,
includes schematics & replacement values reference sheet
92-056 Capacitor kit: Seeburg Models 101, 161 and 201 using TSR6, includes:
Schematics & replacement values reference sheet,
(does not include the capacitor for the Stepper that operates wallboxes)
92-025 Capacitor for Stepper, operates wallboxes in Seeburgs: M100A thru LPC480
91-004 Volume control pot. Models J/JL, V/VL, KS/KD, L100/101, Q & AY (mono.)
76-001 Volume control key for original pots., (Seeburg amps. thru SHFA2 & all Wurlitzer’s)
93-001 Printed circuit board PAU for amplifier, (For Models KS, KD & L 100 only)
93-002 Printed circuit board TEU for receiver, (For Models KS, KD & L 100 only)
90-061 Tube socket / connector socket, 7 pin ceramic pc mount for pc boards in
Seeburg Models KS200, KD200 and L100, each
90-062 Tube socket, 8 pin octal ceramic pc mount for holding 5U4, 6L6 & 2050
tubes in pc boards in Seeburg Models KS200, KD200 and L100, each
90-063 Tube socket / connector socket, 9 pin ceramic pc mount for pc boards in
Seeburg Models KS200, KD200 and L100, each
72-001 Bulb, miniature #12 (selection playing indicator) (1)
72-008 Bulb, miniature #55 (credit lamp) (3), each
70-008 Fluorescent lamp 25 watt 28" T12, cool white is recommended (1)
70-009 Fluorescent lamp 25 watt 28" T12, daylight, optional color
70-050 Colored sleeve for T12 fluorescent lamp, (cut to your specified length),
Specify: sleeve color: red, blue, green, yellow or pink, per foot
- 40 -
$94.50
6.00
22.50
5.00
37.50
14.00
7.00
12.00
18.00
10.00
10.00
15.00
10.00
12.00
65.00
50.00
35.00
50.00
65.00
35.00
12.00
30.00
3.00
50.00
50.00
5.00
5.00
5.00
3.00
1.00
10.00
10.00
1.75
SEEBURG L100 of 1957 and 101
(Sometimes referred to as the L101) of 1958 (Continued)
A-1 PART #
71-006 Ballast, 25 watt, for 1 lamp, new style, (clamped core), made in the U.S.A.
71-035 Ballast, 25 watt, for 1 lamp, original style case & Black color, (Now thermally
protected), made in the U.S.A., includes 2 rubber grommets for mounting
71-028 Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
71-030 Outlet, 3-wire grounded duplex receptacle, (The Receiver plugs into this)
68-004 Caster sockets, use with original Seeburg metal casters or our 2 ½” hard
rubber replacement casters, (made by original supplier to Seeburg), each
68-005 Casters 2 ½” hard rubber, (made by original supplier to Seeburg), each
$12.00
20.00
1.50
12.00
8.00
3.00
7.00
SEEBURG 161 of 1958 80 Records (160 Selections)
A-1 PART #
80-043 Service manual & parts list for 101, 161 & 201, 128 pages, order R-278
80-044 Installation, Operate manual & Trouble Shooting guide for Models
101, 161 & 201, 90 pages, order R-111
80-045 Seeburg 101, 161 & 201, purchase R-278 & R-111, save $9.00, order R-278A
24-001 Lid glass, printed logo, (add $30 for packaging & shipping), not discountable
66-001 Cloud-shaped pricing decals, water transfer to inside of glass, 5 to choose
from, Specify: 1/5¢ Special 6/25¢; 2/10¢ Special 6/25¢; 2/10¢ Special 5/25¢;
1/10¢ Special 3/25¢ or Special 1 play for 25¢, (large size: 5” x 4”), each
94-001 Side glass, Burnt Orange, (factory color), printed, per pair, (add $40 for
packaging & shipping), 161/201 side glass is not discountable
94-002 Side glass, Burnt Orange, printed, left side, (add $40 for pack. & ship.), ea.
94-007 Side glass, Burnt Orange, printed, right side, (add $40 for pack. & ship.), ea
94-003 Side glass, Aqua, (requested color), printed, per pair, (add $40 for
packaging & shipping), 161/201 side glass is not discountable
94-004 Side glass, Aqua, printed, left side, (add $40 for pack. & ship.), each
94-008 Side glass, Aqua, printed, right side, (add $40 for pack. & ship.), each
69-004 Mechanism cover, molded plastic, (primed, gray primer), for Models: R, J/JL,
KS/KD, L100/101, 161, 201, 220 & 222, Logo glass & frame not included
68-050 Barrel screw, holds left side of Mech. cover at correct height, for Seeburg
Models: R, J, JL, KS/KD200, L100, 101, 161, 201, 220 & 222, slotted head
68-051 Barrel screw, holds left side of Mech. cover at correct height, for Seeburg
Models: R, J, JL, KS/KD200, L100, 101, 161, 201, 220 & 222, Phillips head
77-019 Glass for Mech. cover w/printed logo, Models 161 & 201, (frame not included)
73-030 Frame, (plastic holder), for mech. cover glass, painted w/chrome spray paint
24-007 Program title glass, upper
24-008 Program title glass, lower
24-005 MUSIC FOR EVERYONE glass, (choose M.F.E. or EPA RECORDS, not both)
24-006 EP ALBUM RECORDS glass, (choose M.F.E. or EPA RECORDS, not both)
73-016 Price inserts, (5¢ per single, Quarter 6 singles),
for between title strip holders, $5.00 each or 4 pieces
73-017 Picture inserts, original pictures, (for use with 5¢ per single inserts only),
for between title strip holders, $5.00 each or 4 pieces
73-024 Price inserts and Picture inserts, for between title strip holders,
(5¢ per single, Quarter 6 singles), $5.00 each or complete 8 piece set
73-025 Price inserts, (10¢ per single, Quarter 3 singles, Half Dollar 7 singles),
for between title strip holders, $5.00 each or 4 pieces
73-026 Picture inserts, original pictures, (for use with 10¢ per single inserts only),
for between title strip holders, $5.00 each or 4 pieces
- 41 -
$38.00
36.00
65.00
65.00
9.00
195.00
115.00
115.00
195.00
115.00
115.00
125.00
7.00
9.00
25.00
25.00
40.00
40.00
40.00
40.00
15.00
15.00
30.00
15.00
15.00
SEEBURG 161 of 1958 (Continued)
A-1 PART #
73-027 Price inserts and Picture inserts, for between title strip holders,
(10¢ per single, Quarter 3 singles, Half Dollar 7 singles), complete 8 pc. set
Specify # Title headings for Seeburg program holders, Specify: a color and the
A-1 part # from the list at the top of page 15, (11 or 12 piece assortment)
83-004 Plastic Stripper plate (clear), complete with 2 stylus-cleaning brushes,
brush holders, and 6 screws, (all stainless steel hardware)
83-001 Plastic Stripper plate (clear), (with 6 stainless steel screws only)
83-002 Brush holders, hold stylus-cleaning brushes, (stainless steel), per pair
83-003 Brushes, stylus-cleaning, for plastic stripper plate, per pair
83-035 Stylus brush, Seeburg #405219, used to manually clean the styli
& the brushes on the stripper plate, (See page 14 of the installation manual)
84-015 Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
84-001 Motor coupler, connects mech. motor to gear, (replace if rubber is hard)
84-002 Motor support plug, rubber, for under mechanism motor
84-003 Mechanism turntable drive bushings, Seeburg part # 245464, pair
84-004 Mechanism frame rubber bumper, Seeburg part # 245291, pair
74-009 Styli for original Pickering/Seeburg redhead cartridge, (.7 mil
diamond tip for all stereo and mono. records), per pair
83-007 Springs for tone arm, hand made in the U.S.A., exact replacements, pair
78-010 Trip switch, Micro, for tone arm, (for Models B through APFEAI)
83-010 Balance spring for Micro trip switch, for tone arm, each one is hand made
in the U.S.A., Seeburg part # 245817, (for Models B through APFEAI)
83-011 Spring for mechanism reversing switch, (Models B thru STD4), hand made
78-003 Trip coil for mechanism, Models V with 2050 for trip through DS, each
92-015 Capacitor, (run condenser), for mechanism motor, original style/metal can,
for M100A thru STD4, not SX100, for all USA motors, not for Nidec motors
78-022 Free Play Credit Unit, completely bypasses the original credit unit, for
Seeburg Models: V200 with TSR3 receiver, VL200, KS & KD200, 161, 201,
220, 222, AY100, AY160, DS100 and DS160, (This item not discountable)
83-009 Carriage roller for mechanism, Seeburg part # 245082, each
88-017 Spray paint, Burnt Orange, for Models 161/201, acrylic enamel, 12 oz. can
88-018 Spray paint, Aqua, for Models 161/201, acrylic enamel, 12 oz. can
68-009 Rivets and back-up washers, chrome plated, for selection playing plastic,
(for Models KS/KD through 222), 15 rivets & 15 washers
77-013 Credit & Instruction glass, left, (MAKE ANY SELECTION…)
77-014 Coins glass, right, (COINS NICKELS DIMES QUARTERS…)
78-005 Latch bar solenoid for Electrical Selector, all metal frame, as original
68-015 Coin reject plunger, plated, with scavenger wire, (Models G thru APFEAI)
24-004 Diffuser above grill, original shape & printed blue and clear pattern
65-015 Speaker-board screen, (used in back of front metal grill screen), plastic fiber,
charcoal-black, for Seeburg Models 100J thru DS160, 36” X 30”
76-009 Key for cabinet sides and back door, (not cash door), F313
67-004 Cash bag, (duck cloth, as original, hand made in the U.S.A.)
67-012 Cash door, superior grade birch covered plywood, with backup plates,
(for use with metal frame around opening, Models C through LS3)
76-050 Lock, 1 1/8” quality lock, & 2 keys for Reproduction - wooden cash door
76-051 Lock, 1 1/8” quality lock, hardware, & 2 keys for Original metal cash door
76-058 Lock, 1 1/8” quality lock, hardware & 2 keys for lower back door
95-002 Graphics for rear upper cabinet, BLUE, vinyl transfer, (for Models L100,
101, 161, and 201), “SEEBURG SELECT-O-MATIC”
95-003 Graphics for rear door, BLUE, vinyl transfer, (Models L100, 101, 161, 201, 220
& 222), “MASTER VOLUME CONTROL” & “MAIN SWITCH”, “RECORD REJECT”
- 42 -
$30.00
10.00
60.00
50.00
12.00
12.00
3.00
25.00
25.00
2.50
5.00
5.00
50.00
7.00
20.00
8.00
14.00
25.00
30.00
94.50
6.00
16.00
16.00
5.00
18.00
10.00
60.00
25.00
41.50
14.00
7.00
12.00
18.00
10.00
10.00
15.00
10.00
12.00
SEEBURG 161 of 1958 (Continued)
A-1 PART #
92-040 Capacitor kit: Seeburg Models 101, 161 and 201, using Amplifier #: HFMA2,
includes schematics & replacement values reference sheet
92-056 Capacitor kit: Seeburg Models 101, 161 and 201 using TSR6, includes:
Schematics & replacement values reference sheet,
(does not include the capacitor for the Stepper that operates wallboxes)
92-025 Capacitor for Stepper, operates wallboxes in Seeburgs: M100A thru LPC480
76-001 Volume control key for original pots., (Seeburg amps. thru SHFA2 & all Wurlitzer’s)
72-001 Bulb, miniature #12 (selection playing indicator) (1)
72-008 Bulb, miniature #55 (credit lamp) (3) and (grill ornaments) (2), each
72-015 Bulb, miniature #455 (flasher for grill ornaments) (2, optional), each
70-008 Fluorescent lamp 25 watt 28" T12, cool white is recommended, (2), each
70-009 Fluorescent lamp 25 watt 28" T12, daylight (optional color)
70-050 Colored sleeve for T12 fluorescent lamp, (cut to your specified length),
Specify: sleeve color: red, blue, green, yellow or pink, per foot
71-006 Ballast, 25 watt, for 1 lamp, new style, (clamped core), made in the U.S.A.
71-035 Ballast, 25 watt, for 1 lamp, original style case & Black color, (Now thermally
protected), made in the U.S.A., includes 2 rubber grommets for mounting
71-028 Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
71-030 Outlet, 3-wire grounded duplex receptacle, (The Receiver plugs into this)
68-004 Caster sockets, use with original Seeburg metal casters or our 2 ½” hard
rubber replacement casters, (made by original supplier to Seeburg), each
68-005 Casters 2 ½” hard rubber, (made by original supplier to Seeburg), each
$65.00
35.00
12.00
3.00
3.00
1.00
2.00
10.00
10.00
1.75
12.00
20.00
1.50
12.00
8.00
3.00
7.00
SEEBURG 201 of 1958 100 Records (200 Selections)
A-1 PART #
80-043 Service manual & parts list for 101, 161 & 201, 128 pages, order R-278
80-044 Installation, Operate manual & Trouble Shooting guide for Models
101, 161 & 201, 90 pages, order R-111
80-045 Seeburg 101, 161 & 201, purchase R-278 & R-111, save $9.00, order R-278A
25-001 Lid glass, printed logo, (add $30 for packaging & shipping), not discountable
25-010 Decal, for inside of Lid glass, water transfer, SELECT-O-MATIC Two Hundred
66-001 Cloud-shaped pricing decals, water transfer to inside of glass, 5 to choose
from, Specify: 1/5¢ Special 6/25¢; 2/10¢ Special 6/25¢; 2/10¢ Special 5/25¢;
1/10¢ Special 3/25¢ or Special 1 play for 25¢, (large size: 5” x 4”), each
94-001 Side glass, Burnt Orange, (factory color), printed, per pair, (add $40 for
packaging & shipping), 161/201 side glass is not discountable
94-002 Side glass, Burnt Orange, printed, left side, (add $40 for pack. & ship.), ea.
94-007 Side glass, Burnt Orange, printed, right side, (add $40 for pack./ship.), ea.
94-003 Side glass, Aqua, (requested color), printed, per pair, (add $40 for
packaging & shipping), 161/201 side glass is not discountable
94-004 Side glass, Aqua, printed, left side, (add $40 for pack. & ship.), each
94-008 Side glass, Aqua, printed, right side, (add $40 for pack. & ship.), each
69-004 Mechanism cover, molded plastic, (primed, gray primer), for Models: R, J/JL,
KS/KD, L100/101, 161, 201, 220 & 222, Logo glass & frame not included
68-050 Barrel screw, holds left side of Mech. cover at correct height, for Seeburg
Models: R, J, JL, KS/KD200, L100, 101, 161, 201, 220 & 222, slotted head
68-051 Barrel screw, holds left side of Mech. cover at correct height, for Seeburg
Models: R, J, JL, KS/KD200, L100, 101, 161, 201, 220 & 222, Phillips head
77-019 Glass for Mech. cover w/printed logo, Models 161 & 201, (frame not included)
73-030 Frame, (plastic holder), for mech. cover glass, painted w/chrome spray paint
- 43 -
$38.00
36.00
65.00
65.00
8.00
9.00
195.00
115.00
115.00
195.00
115.00
115.00
125.00
7.00
9.00
25.00
25.00
SEEBURG 201 of 1958 (Continued)
A-1 PART #
25-007
25-008
25-004
25-006
73-016
73-017
73-024
73-025
73-026
73-027
Specify #
83-004
83-001
83-002
83-003
83-035
84-015
84-001
84-002
84-003
84-004
74-009
83-007
78-010
83-010
83-011
78-003
92-015
78-022
83-009
88-017
88-018
68-009
77-013
25-009
Program title glass, upper
Program title glass, lower
MUSIC FOR EVERYONE glass, (choose M.F.E. or EPA RECORDS, not both)
EP ALBUM RECORDS glass, (choose M.F.E. or EPA RECORDS, not both)
Price inserts, (5¢ per single, Quarter 6 singles),
for between title strip holders, $5.00 each or 4 pieces
Picture inserts, original pictures, (for use with 5¢ per single inserts only),
for between title strip holders, $5.00 each or 4 pieces
Price inserts and Picture inserts, for between title strip holders,
(5¢ per single, Quarter 6 singles), $5.00 each or complete 8 piece set
Price inserts, (10¢ per single, Quarter 3 singles, Half Dollar 7 singles),
for between title strip holders, $5.00 each or 4 pieces
Picture inserts, original pictures, (for use with 10¢ per single inserts only),
for between title strip holders, $5.00 each or 4 pieces
Price inserts and Picture inserts, for between title strip holders,
(10¢ per single, Quarter 3 singles, Half Dollar 7 singles), complete 8 pc. set
Title headings for Seeburg program holders, Specify: a color and the
A-1 part # from the list at the top of page 15, (11 or 12 piece assortment)
Plastic Stripper plate (clear), complete with 2 stylus-cleaning brushes,
brush holders, and 6 screws, (all stainless steel hardware)
Plastic Stripper plate (clear), (with 6 stainless steel screws only)
Brush holders, hold stylus-cleaning brushes, (stainless steel), per pair
Brushes, stylus-cleaning, for plastic stripper plate, per pair
Stylus brush, Seeburg #405219, used to manually clean the styli
& the brushes on the stripper plate, (See page 14 of the installation manual)
Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
Motor coupler, connects mech. motor to gear, (replace if rubber is hard)
Motor support plug, rubber, for under mechanism motor
Mechanism turntable drive bushings, Seeburg part # 245464, pair
Mechanism frame rubber bumper, Seeburg part # 245291, pair
Styli for original Pickering/Seeburg redhead cartridge, (.7 mil
diamond tip for all stereo and mono. records), per pair
Springs for tone arm, hand made in the U.S.A., exact replacements, pair
Trip switch, Micro, for tone arm, (for Models B through APFEAI)
Balance spring for Micro trip switch, for tone arm, each one is hand made
in the U.S.A., Seeburg part # 245817, (for Models B through APFEAI)
Spring for mechanism reversing switch, (Models B thru STD4), hand made
Trip coil for mechanism, Models V with 2050 for trip through DS, each
Capacitor, (run condenser), for mechanism motor, original style/metal can,
for M100A thru STD4, not SX100, for all USA motors, not for Nidec motors
Free Play Credit Unit, completely bypasses the original credit unit, for
Seeburg Models: V200 with TSR3 receiver, VL200, KS & KD200, 161, 201,
220, 222, AY100, AY160, DS100 and DS160, (This item not discountable)
Carriage roller for mechanism, Seeburg part # 245082, each
Spray paint, Burnt Orange, for Models 161/201, acrylic enamel, 12 oz. can
Spray paint, Aqua, for Models 161/201, acrylic enamel, 12 oz. can
Rivets and back-up washers, chrome plated, for selection playing plastic,
(for Models KS/KD through 222), 15 rivets & 15 washers
Credit & Instruction glass, left, (MAKE ANY SELECTION…)
Coins glass, right, (COINS SELECT AFTER EACH HALF DOLLAR…), (201 only)
- 44 -
$40.00
40.00
40.00
40.00
15.00
15.00
30.00
15.00
15.00
30.00
10.00
60.00
50.00
12.00
12.00
3.00
25.00
25.00
2.50
5.00
5.00
50.00
7.00
20.00
8.00
14.00
25.00
30.00
94.50
6.00
16.00
16.00
5.00
18.00
10.00
SEEBURG 201 of 1958 (Continued)
A-1 PART #
78-005
68-015
25-003
65-015
76-009
67-004
67-012
76-050
76-051
76-058
81-012
95-002
95-003
92-040
92-056
92-025
76-001
72-001
72-008
72-015
70-010
70-050
71-006
71-035
71-028
71-016
71-030
68-004
68-005
Latch bar solenoid for Electrical Selector, all metal frame, as original
Coin reject plunger, plated, with scavenger wire, (Models G thru APFEAI)
Diffuser above grill, original shape and printed blue and clear pattern
Speaker-board screen, (used in back of front metal grill screen), plastic fiber,
charcoal-black, for Seeburg Models 100J thru DS160, 36” X 30”
Key for cabinet sides and back door, (not cash door), F313
Cash bag, (duck cloth, as original, hand made in the U.S.A.)
Cash door, superior grade birch covered plywood, with backup plates,
(for use with metal frame around opening, Models C through LS3)
Lock, 1 1/8” quality lock, & 2 keys for Reproduction - wooden cash door
Lock, 1 1/8” quality lock, hardware, & 2 keys for Original metal cash door
Lock, 1 1/8” quality lock, hardware & 2 keys for lower back door
I.D. plate, Model 201, (as original), no serial number, for back of cabinet
Graphics for rear upper cabinet, BLUE, vinyl transfer, (for Models L100,
101, 161, and 201), “SEEBURG SELECT-O-MATIC”
Graphics for rear door, BLUE, vinyl transfer, (Models L100, 101, 161, 201, 220
& 222), “MASTER VOLUME CONTROL” & “MAIN SWITCH”, “RECORD REJECT”
Capacitor kit: Seeburg Models 101, 161 and 201, using Amplifier #: HFMA2,
includes schematics & replacement values reference sheet
Capacitor kit: Seeburg Models 101, 161 and 201 using TSR6, includes:
Schematics & replacement values reference sheet,
(does not include the capacitor for the Stepper that operates wallboxes)
Capacitor for Stepper, operates wallboxes in Seeburgs: M100A thru LPC480
Volume control key for original pots., (Seeburg amps. thru SHFA2 & all Wurlitzer’s)
Bulb, miniature #12 (selection playing indicator) (1)
Bulb, miniature #55 (credit lamp) (3) and (grill ornaments) (3), each
Bulb, miniature #455 (flasher for grill ornaments) (3, optional), each
Fluorescent lamp 25 watt 33” T12, cool white is recommended, (2), each
Colored sleeve for T12 fluorescent lamp, (cut to your specified length),
Specify: sleeve color: red, blue, green, yellow or pink, per foot
Ballast, 25 watt, for 1 lamp, new style, (clamped core), made in the U.S.A.
Ballast, 25 watt, for 1 lamp, original style case & Black color, (Now thermally
protected), made in the U.S.A., includes 2 rubber grommets for mounting
Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
Outlet, 3-wire grounded duplex receptacle, (The Receiver plugs into this)
Caster sockets, use with original Seeburg metal casters or our 2 ½” hard
rubber replacement casters, (made by original supplier to Seeburg), each
Casters 2 ½” hard rubber, (made by original supplier to Seeburg), each
$60.00
25.00
42.50
14.00
7.00
12.00
18.00
10.00
10.00
15.00
15.00
10.00
12.00
65.00
35.00
12.00
3.00
3.00
1.00
2.00
10.00
1.75
12.00
20.00
1.50
12.00
8.00
3.00
7.00
SEEBURG 220 of 1958 – 1959 50 Records (100 Selections)
A-1 PART #
80-049 Service & parts manual, Seeburg 220 & 222, 174 pages, order R-274
80-050 Installation, Operation manual, Trouble Shooting guide & Stereo system
information, Seeburg 220 & 222, 68 pages, order R-439
80-051 Seeburg 220 & 222, purchase R-274 & R-439, save $10.00, order R-274A
94-013 Lid glass, 3/16" plate, no printing – as original, (add $30 for packing
& shipping), 220/222 lid glass is not discountable
66-001 Cloud-shaped pricing decals, water transfer to inside of glass, 5 to choose
from, Specify: 1/5¢ Special 6/25¢; 2/10¢ Special 6/25¢; 2/10¢ Special 5/25¢;
1/10¢ Special 3/25¢ or Special 1 play for 25¢, (large size: 5” x 4”), each
- 45 -
$42.00
33.00
65.00
45.00
9.00
SEEBURG 220 of 1958 – 1959 (Continued)
A-1 PART #
94-005 Side glass, exact reproductions, per pair, (add $40 for packing,
Insurance and shipping), (220/222 side glass is not discountable)
94-006 Side glass, left side, each, (add $40 for packaging & shipping), each
94-012 Side glass, right side, each, (add $40 for packaging & shipping), each
69-009 Mechanism cover, molded plastic, original Pink color molded in,
for Models 220 & 222 only, Logo glass & glass frame not included
69-004 Mechanism cover, molded plastic, (primed, gray primer), for Models: R, J/JL,
KS/KD, L100/101, 161, 201, 220 & 222, Logo glass & frame not included
68-050 Barrel screw, holds left side of Mech. cover at correct height, for Seeburg
Models: R, J, JL, KS/KD200, L100, 101, 161, 201, 220 & 222, slotted head
68-051 Barrel screw, holds left side of Mech. cover at correct height, for Seeburg
Models: R, J, JL, KS/KD200, L100, 101, 161, 201, 220 & 222, Phillips head
26-003 Program title glass, screen-printed as original
Specify # Title headings for Seeburg program holders, Specify: a color and the
A-1 part # from the list at the top of page 15, (11 or 12 piece assortment)
83-005 Stripper plate (clear), (some 220’s had a stripper plate)
83-006 Brushes, stylus-cleaning, double sided
78-012 Cam switch bank, 8 switches, for mechanism w/stereo, Seeburg #249938
84-015 Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
84-001 Motor coupler, connects mech. motor to gear, (replace if rubber is hard)
84-002 Motor support plug, rubber, for under mechanism motor
84-003 Mechanism turntable drive bushings, Seeburg part # 245464, pair
84-004 Mechanism frame rubber bumper, Seeburg part # 245291, pair
74-010 Styli, T shaped, for original Pickering/Seeburg cartridges, (.7 mil
diamond tip for all stereo and mono. records), per pair
83-007 Springs for tone arm, hand made in the U.S.A., exact replacements, pair
78-010 Trip switch, Micro, for tone arm, (for Models B through APFEAI)
83-010 Balance spring for Micro trip switch, for tone arm, each one is hand made
in the U.S.A., Seeburg part # 245817, (for Models B through APFEAI)
83-011 Spring for mechanism reversing switch, (Models B thru STD4), hand made
78-003 Trip coil for mechanism, Models V with 2050 for trip through DS, each
92-015 Capacitor, (run condenser), for mechanism motor, original style/metal can,
for M100A thru STD4, not SX100, for all USA motors, not for Nidec motors
78-022 Free Play Credit Unit, completely bypasses the original credit unit, for
Seeburg Models: V200 with TSR3 receiver, VL200, KS & KD200, 161, 201,
220, 222, AY100, AY160, DS100 and DS160, (This item not discountable)
83-009 Carriage roller for mechanism, Seeburg part # 245082, each
95-004 Graphics for mechanism ends, Silver, vinyl transfer, (for Models 220 and
Q100 only), “HIGH FIDELITY” and “SELECT-O-MATIC”, 2 piece set
68-009 Rivets and back-up washers, chrome plated, for selection playing plastic,
(for Models KS/KD through 222), 15 rivets & 15 washers
77-013 Credit & Instruction glass, left, (MAKE ANY SELECTION…)
26-004 Pricing glass center, Model 220 only, "5¢ per, Quarter 6 singles"
26-005 Pricing glass center, Model 220 only, "10¢ per, Quarter 3 singles"
77-014 Coins glass, right, (COINS NICKELS DIMES QUARTERS…)
78-005 Latch bar solenoid for Electrical Selector, all metal frame, as original
68-015 Coin reject plunger, plated, with scavenger wire, (Models G thru APFEAI)
73-031 Diffuser above grill, original shape and printed aqua and red pattern
65-015 Speaker-board screen, (used in back of front metal grill screen), plastic fiber,
charcoal-black, for Seeburg Models 100J thru DS160, 36” X 30”
76-010 Key for cabinet sides and back door, (not cash door), F264
- 46 -
$275.00
150.00
150.00
150.00
125.00
7.00
9.00
40.00
10.00
50.00
12.00
15.00
25.00
25.00
2.50
5.00
5.00
80.00
7.00
20.00
8.00
14.00
25.00
30.00
94.50
6.00
12.00
5.00
18.00
10.00
10.00
10.00
60.00
25.00
42.50
14.00
7.00
SEEBURG 220 of 1958 – 1959 (Continued)
A-1 PART #
67-004 Cash bag, (duck cloth, as original, hand made in the U.S.A.)
67-012 Cash door, superior grade birch covered plywood, with backup plates,
(for use with metal frame around opening, Models C through LS3)
76-050 Lock, 1 1/8” quality lock, & 2 keys for Reproduction - wooden cash door
76-051 Lock, 1 1/8” quality lock, hardware, & 2 keys for Original metal cash door
76-058 Lock, 1 1/8” quality lock, hardware & 2 keys for lower back door
95-005 Graphic for rear upper cabinet, BLUE, vinyl transfer,
(for Models 220 & 222 only), “SEEBURG STEREOPHONIC”
95-003 Graphics for rear door, BLUE, vinyl transfer, (Models L100, 101, 161, 201, 220
& 222), “MASTER VOLUME CONTROL” & “MAIN SWITCH”, “RECORD REJECT”
92-042 Capacitor kit: Seeburg Models 220, 222, Q100 & Q160, Amp. #: SHFA1,
includes schematics & replacement values reference sheet
92-045 Capacitor kit: Seeburg Models 220, 222, Q100 & Q160, Amp. #: SHFA2,
includes schematics & replacement values reference sheet
91-002 Volume control pot. (for stereo amplifiers): SHFA1, SHFA2 and TSA1
through TSA10, Also: Stereo Amps. in Rock-Ola Models 1460 through 437
92-053 Capacitor kit for TSU1 thru TSU7, Tormat Selector Units, in Seeburg Models
220 thru DS160, includes schematics & replacement values reference sheet,
(does not include the capacitor for the Stepper that operates wallboxes)
92-025 Capacitor for Stepper, operates wallboxes in Seeburgs: M100A thru LPC480
76-001 Volume control key for original pots., (Seeburg amps. thru SHFA2 & all Wurlitzer’s)
72-001 Bulb, miniature #12 (selection playing indicator) (1)
72-008 Bulb, miniature #55 (credit lamps) (3), each
72-010 Bulb, miniature #63 (grill ornament lamps) (2), each
70-008 Fluorescent lamp 25 watt 28" T12, cool white is recommended, (2), each
70-009 Fluorescent lamp 25 watt 28" T12, daylight, optional color
70-050 Colored sleeve for T12 fluorescent lamp, (cut to your specified length),
Specify: sleeve color: red, blue, green, yellow or pink, per foot
71-006 Ballast, 25 watt, for 1 lamp, new style, (clamped core), made in the U.S.A.
71-035 Ballast, 25 watt, for 1 lamp, original style case & Black color, (Now thermally
protected), made in the U.S.A., includes 2 rubber grommets for mounting
71-028 Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
68-004 Caster sockets, use with original Seeburg metal casters or our 2 ½” hard
rubber replacement casters, (made by original supplier to Seeburg), each
68-005 Casters 2 ½” hard rubber, (made by original supplier to Seeburg), each
$12.00
18.00
10.00
10.00
15.00
10.00
12.00
80.00
80.00
30.00
32.50
12.00
3.00
3.00
1.00
1.50
10.00
10.00
1.75
12.00
20.00
1.50
12.00
3.00
7.00
SEEBURG 222 of 1958 – 1959 80 Records (160 Selections)
A-1 PART #
80-049 Service & parts manual, Seeburg 220 & 222, 174 pages, order R-274
80-050 Installation, Operation manual, Trouble Shooting guide & Stereo system
information, Seeburg 220 & 222, 68 pages, order R-439
80-051 Seeburg 220 & 222, purchase R-274 & R-439, save $10.00, order R-274A
94-013 Lid glass, 3/16" plate, no printing – as original, (add $40 for packing
& shipping), 220/222 lid glass is not discountable
66-001 Cloud-shaped pricing decals, water transfer to inside of glass, 5 to choose
from, Specify: 1/5¢ Special 6/25¢; 2/10¢ Special 6/25¢; 2/10¢ Special 5/25¢;
1/10¢ Special 3/25¢ or Special 1 play for 25¢, (large size: 5” x 4”), each
94-005 Side glass, exact reproductions, per pair, (add $40 for packaging,
Insurance and shipping), 220/222 side glass is not discountable
- 47 -
$42.00
33.00
65.00
45.00
9.00
275.00
SEEBURG 222 of 1958 – 1959 (Continued)
A-1 PART #
94-006 Side glass, left side, each, (add $40 for packaging & shipping), each
94-012 Side glass, right side, each, (add $40 for packaging & shipping), each
69-009 Mechanism cover, molded plastic, original Pink color molded in,
for Models 220 & 222 only, Logo glass & glass frame not included
69-004 Mechanism cover, molded plastic, (primed, gray primer), for Models: R, J/JL,
KS/KD, L100/101, 161, 201, 220 & 222, Logo glass & frame not included
68-050 Barrel screw, holds left side of Mech. cover at correct height, for Seeburg
Models: R, J, JL, KS/KD200, L100, 101, 161, 201, 220 & 222, slotted head
68-051 Barrel screw, holds left side of Mech. cover at correct height, for Seeburg
Models: R, J, JL, KS/KD200, L100, 101, 161, 201, 220 & 222, Phillips head
27-001 Glass for mechanism cover, with printed logo, 222 only, (frame not included)
73-030 Frame, (plastic holder), for mech. cover glass, painted w/chrome spray paint
27-004 STEREOPHONIC glass, above upper program title glass
27-005 Program title glass, upper, Model 222 only
27-006 Program title glass, lower, Model 222 only
27-007 Price inserts, (10¢ per single, Quarter 3 singles, Half Dollar 7 singles),
for between title strip holders, $5.00 each or 4 pieces
27-008 Picture inserts, original pictures, between title strip holders, $5.00 ea. or 4 pcs.
27-009 Price inserts and Picture inserts, for between title strip holders,
(10¢ per single, Quarter 3 singles, Half Dollar 7 singles), complete 8 pc. set
Specify # Title headings for Seeburg program holders, Specify: a color and the
A-1 part # from the list at the top of page 15, (11 or 12 piece assortment)
83-006 Brushes, stylus-cleaning, double sided
78-012 Cam switch bank, 8 switches, for mechanism w/stereo, Seeburg #249938
84-015 Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
84-001 Motor coupler, connects mech. motor to gear, (replace if rubber is hard)
84-002 Motor support plug, rubber, for under mechanism motor
84-003 Mechanism turntable drive bushings, Seeburg part # 245464, pair
84-004 Mechanism frame rubber bumper, Seeburg part # 245291, pair
74-010 Styli, T shaped, for original Pickering/Seeburg cartridges, (.7 mil
diamond tip for all stereo and mono. records), per pair
83-007 Springs for tone arm, hand made in the U.S.A., exact replacements, pair
78-010 Trip switch, Micro, for tone arm, (for Models B through APFEAI)
83-010 Balance spring for Micro trip switch, for tone arm, each one is hand made
in the U.S.A., Seeburg part # 245817, (for Models B through APFEAI)
83-011 Spring for mechanism reversing switch, (Models B thru STD4), hand made
78-003 Trip coil for mechanism, Models V with 2050 for trip through DS, each
92-015 Capacitor, (run condenser), for mechanism motor, original style/metal can,
for M100A thru STD4, not SX100, for all USA motors, not for Nidec motors
78-022 Free Play Credit Unit, completely bypasses the original credit unit, for
Seeburg Models: V200 with TSR3 receiver, VL200, KS & KD200, 161, 201,
220, 222, AY100, AY160, DS100 and DS160, (This item not discountable)
83-009 Carriage roller for mechanism, Seeburg part # 245082, each
78-005 Latch bar solenoid for Electrical Selector, all metal frame, as original
95-006 Graphics for mechanism ends, vinyl transfer, (for Model 222 only), Silver
“HIGH FIDELITY and SELECT-O-MATIC”, (2) Silver “S” and
(2) Pink “S”, original style graphics, 6 piece set
68-009 Rivets and back-up washers, chrome plated, for selection playing plastic,
(for Models KS/KD through 222), 15 rivets & 15 washers
77-013 Credit & Instruction glass, left, (MAKE ANY SELECTION…)
77-014 Coins glass, right, (COINS NICKELS DIMES QUARTERS…)
- 48 -
$150.00
150.00
150.00
125.00
7.00
9.00
25.00
25.00
40.00
40.00
40.00
15.00
15.00
30.00
10.00
12.00
15.00
25.00
25.00
2.50
5.00
5.00
80.00
7.00
20.00
8.00
14.00
25.00
30.00
94.50
6.00
60.00
12.00
5.00
18.00
10.00
SEEBURG 222 of 1958 – 1959 (Continued)
A-1 PART #
68-015 Coin reject plunger, plated, with scavenger wire, (Models G thru APFEAI)
73-031 Diffuser above grill, original shape and printed aqua and red pattern
65-015 Speaker-board screen, (used in back of front metal grill screen), plastic fiber,
charcoal-black, for Seeburg Models 100J thru DS160, 36” X 30”
76-010 Key for cabinet sides and back door, (not cash door), F264
67-004 Cash bag, (duck cloth, as original, hand made in the U.S.A.)
67-012 Cash door, superior grade birch covered plywood, with backup plates,
(for use with metal frame around opening, Models C through LS3)
76-050 Lock, 1 1/8” quality lock, & 2 keys for Reproduction - wooden cash door
76-051 Lock, 1 1/8” quality lock, hardware, & 2 keys for Original metal cash door
76-058 Lock, 1 1/8” quality lock, hardware & 2 keys for lower back door
81-013 I.D. plate, Model 222, (as original), no serial number, for back of cabinet
95-005 Graphic for rear upper cabinet, BLUE, vinyl transfer,
(for Models 220 & 222 only), “SEEBURG STEREOPHONIC”
95-003 Graphics for rear door, BLUE, vinyl transfer, (Models L100, 101, 161, 201, 220
& 222), “MASTER VOLUME CONTROL” & “MAIN SWITCH”, “RECORD REJECT”
92-042 Capacitor kit: Seeburg Models 220, 222, Q100 & Q160, Amp. #: SHFA1,
includes schematics & replacement values reference sheet
92-045 Capacitor kit: Seeburg Models 220, 222, Q100 & Q160, Amp. #: SHFA2,
includes schematics & replacement values reference sheet
91-002 Volume control pot. (for stereo amplifiers): SHFA1, SHFA2 and TSA1
through TSA10, Also: Stereo Amps. in Rock-Ola Models 1460 through 437
92-053 Capacitor kit for TSU1 thru TSU7, Tormat Selector Units, in Seeburg Models
220 thru DS160, includes schematics & replacement values reference sheet,
(does not include the capacitor for the Stepper that operates wallboxes)
92-025 Capacitor for Stepper, operates wallboxes in Seeburgs: M100A thru LPC480
76-001 Volume control key for original pots., (Seeburg amps. thru SHFA2 & all Wurlitzer’s)
72-001 Bulb, miniature #12 (selection playing indicator) (1)
72-008 Bulb, miniature #55 (credit lamps) (3), each
72-010 Bulb, miniature #63 (grill ornament lamps) (2), each
70-008 Fluorescent lamp 25 watt 28" T12, cool white is recommended, (2), each
70-009 Fluorescent lamp 25 watt 28" T12, daylight, optional color
70-050 Colored sleeve for T12 fluorescent lamp, (cut to your specified length),
Specify: sleeve color: red, blue, green, yellow or pink, per foot
71-006 Ballast, 25 watt, for 1 lamp, new style, (clamped core), made in the U.S.A.
71-035 Ballast, 25 watt, for 1 lamp, original style case & Black color, (Now thermally
protected), made in the U.S.A., includes 2 rubber grommets for mounting
71-028 Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
71-030 Outlet, 3-wire grounded duplex receptacle, (The Receiver plugs into this)
68-004 Caster sockets, use with original Seeburg metal casters or our 2 ½” hard
rubber replacement casters, (made by original supplier to Seeburg), each
68-005 Casters 2 ½” hard rubber, (made by original supplier to Seeburg), each
$25.00
42.50
14.00
7.00
12.00
18.00
10.00
10.00
15.00
15.00
10.00
12.00
80.00
80.00
30.00
32.50
12.00
3.00
3.00
1.00
1.50
10.00
10.00
1.75
12.00
20.00
1.50
12.00
8.00
3.00
7.00
SEEBURG Q100 of 1959 – 1960 (Sometimes referred to as the AQ100)
50 Records (100 Selections)
A-1 PART #
80-052 Service & parts manual, Seeburg Q100 & Q160, 128 pages, order R-162
80-053 Installation, Operation manual, Trouble Shooting guide &
Cabinet Parts, Seeburg Q100 & Q160, 76 pages, order R-424
80-054 Seeburg Q100 & Q160, purchase R-162 & R-424, save $6.00, order R-162A
28-001 Upper lid glass, (Q100 only), “Seeburg HIGH FIDELITY”, (add $15 for shipping)
- 49 -
$38.00
32.00
64.00
140.00
SEEBURG Q100 of 1959 – 1960 (Continued)
A-1 PART #
28-002
77-020
77-015
77-016
77-017
68-015
Specify #
83-006
78-012
84-015
84-001
84-002
84-003
84-004
74-010
83-007
78-010
83-010
83-011
78-003
92-015
78-024
83-009
88-020
95-004
73-060
65-015
76-010
67-004
67-012
76-050
76-051
76-058
81-014
95-010
95-011
92-042
92-043
Lower lid glass, Q100 only, (add $40 for pack. & shipping of lower or both)
Make Any Selection glass, left side
Pricing glass, center, Q100 only, 10¢ per selection, Quarter 3 selections
Pricing glass, center, Q100 only, 10¢ per sel., Quarter 3 sel., ½ Dollar 7 sel.
Coins glass, right side
Coin reject plunger, plated, with scavenger wire, (Models G thru APFEAI)
Title headings for Seeburg program holders, Specify: a color and the
A-1 part # from the list at the top of page 15, (11 or 12 piece assortment)
Brushes, stylus-cleaning, double sided
Cam switch bank, 8 switches, for mechanism w/stereo, Seeburg #249463
Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
Motor coupler, connects mech. motor to gear, (replace if rubber is hard)
Motor support plug, rubber, for under mechanism motor
Mechanism turntable drive bushings, Seeburg part # 245464, pair
Mechanism frame rubber bumper, Seeburg part # 245291, pair
Styli, T shaped, for original Pickering/Seeburg cartridges, (.7 mil
diamond tip for all stereo and mono. records), per pair
Springs for tone arm, hand made in the U.S.A., exact replacements, pair
Trip switch, Micro, for tone arm, (for Models B through APFEAI)
Balance spring for Micro trip switch, for tone arm, each one is hand made
in the U.S.A., Seeburg part # 245817, (for Models B through APFEAI)
Spring for mechanism reversing switch, (Models B thru STD4), hand made
Trip coil for mechanism, Models V with 2050 for trip through DS, each
Capacitor, (run condenser), for mechanism motor, original style/metal can,
for M100A thru STD4, not SX100, for all USA motors, not for Nidec motors
Free Play Credit Unit, completely bypasses the original credit unit, for
Seeburg Models: L100, 101, Q100 & Q160, (This item is not discountable)
Carriage roller for mechanism, Seeburg part # 245082, each
Spray paint, Medium Blue, Models Q & AY, for inside cabinet, 12 oz. can
Graphics for mechanism ends, Silver, vinyl transfer, (for Models 220 and
Q100 only), “HIGH FIDELITY” and “SELECT-O-MATIC”, 2 piece set
Diffuser above front grill, (silk-screened, all blue, as original)
Speaker-board screen, (used in back of front metal grill screen), plastic fiber,
charcoal-black, for Seeburg Models 100J thru DS160, 36” X 30”
Key for cabinet sides and back door, (not cash door), F264
Cash bag, (duck cloth, as original, hand made in the U.S.A.)
Cash door, superior grade birch covered plywood, with backup plates,
(for use with metal frame around opening, Models C through LS3)
Lock, 1 1/8” quality lock, & 2 keys for Reproduction - wooden cash door
Lock, 1 1/8” quality lock, hardware, & 2 keys for Original metal cash door
Lock, 1 1/8” quality lock, hardware & 2 keys for lower back door
I.D. plate, Models: Q100 and Y100, (as original, Q or Y is not printed
on this I.D. plate), no serial number, for back of cabinet
Graphic for rear upper cabinet, White, vinyl transfer,
(for Models Q100 and Q160 only), “SEEBURG”
Graphics for lower rear door, White, vinyl transfer,
(for Models Q100, and Q160 only), “MASTER VOLUME CONTROL”
and “MAIN SWITCH”, “RECORD REJECT”, 2 piece set
Capacitor kit: Seeburg Models 220, 222, Q100 & Q160, Amp. #: SHFA1,
includes schematics & replacement values reference sheet
Capacitor kit: Seeburg Q100 and Q160, using Amplifier # C1HFA1 or
C2HFA1, includes schematics & replacement values reference sheet
- 50 -
$140.00
10.00
15.00
15.00
10.00
25.00
10.00
12.00
15.00
25.00
25.00
2.50
5.00
5.00
80.00
7.00
20.00
8.00
14.00
25.00
30.00
94.50
6.00
16.00
12.00
15.00
14.00
7.00
12.00
18.00
10.00
10.00
15.00
15.00
10.00
12.00
80.00
65.00
SEEBURG Q100 of 1959 – 1960 (Continued)
A-1 PART #
28-002
77-020
77-015
77-016
77-017
68-015
Specify #
83-006
78-012
84-015
84-001
84-002
84-003
84-004
74-010
83-007
78-010
71-006
71-035
71-028
71-016
71-030
Lower lid glass, Q100 only, (add $40 for pack. & shipping of lower or both)
Make Any Selection glass, left side
Pricing glass, center, Q100 only, 10¢ per selection, Quarter 3 selections
Pricing glass, center, Q100 only, 10¢ per sel., Quarter 3 sel., ½ Dollar 7 sel.
Coins glass, right side
Coin reject plunger, plated, with scavenger wire, (Models G thru APFEAI)
Title headings for Seeburg program holders, Specify: a color and the
A-1 part # from the list at the top of page 15, (11 or 12 piece assortment)
Brushes, stylus-cleaning, double sided
Cam switch bank, 8 switches, for mechanism w/stereo, Seeburg #249463
Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
Motor coupler, connects mech. motor to gear, (replace if rubber is hard)
Motor support plug, rubber, for under mechanism motor
Mechanism turntable drive bushings, Seeburg part # 245464, pair
Mechanism frame rubber bumper, Seeburg part # 245291, pair
Styli, T shaped, for original Pickering/Seeburg cartridges, (.7 mil
diamond tip for all stereo and mono. records), per pair
Springs for tone arm, hand made in the U.S.A., exact replacements, pair
Trip switch, Micro, for tone arm, (for Models B through APFEAI)
Ballast, 25 watt, for 1 lamp, new style, (clamped core), made in the U.S.A.
Ballast, 25 watt, for 1 lamp, original style case & Black color, (Now thermally
protected), made in the U.S.A., includes 2 rubber grommets for mounting
Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
Outlet, 3-wire grounded duplex receptacle, (The Receiver plugs into this)
$140.00
10.00
15.00
15.00
10.00
25.00
10.00
12.00
15.00
25.00
25.00
2.50
5.00
5.00
80.00
7.00
20.00
12.00
20.00
1.50
12.00
8.00
SEEBURG Q160 of 1959 – 1960 (Sometimes referred to as the AQ160)
80 Records (160 Selections)
A-1 PART #
80-052 Service & parts manual, Seeburg Q100 & Q160, 128 pages, order R-162
80-053 Installation, Operation manual, Trouble Shooting guide &
Cabinet Parts, Seeburg Q100 & Q160, 76 pages, order R-424
80-054 Seeburg Q100 & Q160, purchase R-162 & R-424, save $6.00, order R-162A
29-001 Upper lid glass, Q160, “Seeburg PRESENTS IN 33⅓ STEREO, ARTIST OF
THE WEEK”, (add $40 for packaging & shipping of upper or both glasses)
29-002 Lower lid glass, Q160, (add $40 for packaging & shipping of lower or both)
77-020 Make Any Selection glass, left side
77-017 Coins glass, right side
68-015 Coin reject plunger, plated, with scavenger wire, (Models G thru APFEAI)
Specify # Title headings for Seeburg program holders, Specify: a color and the
A-1 part # from the list at the top of page 15, (11 or 12 piece assortment)
29-003 Price card insert for program title board (10¢ per, Quarter 3, half dollar 7)
83-006 Brushes, stylus-cleaning, double sided
78-012 Cam switch bank, 8 switches, for mechanism w/stereo, Seeburg #249463
84-015 Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
84-001 Motor coupler, connects mech. motor to gear, (replace if rubber is hard)
84-002 Motor support plug, rubber, for under mechanism motor
84-003 Mechanism turntable drive bushings, Seeburg part # 245464, pair
84-004 Mechanism frame rubber bumper, Seeburg part # 245291, pair
- 51 -
$38.00
32.00
64.00
150.00
140.00
10.00
10.00
25.00
10.00
8.00
12.00
15.00
25.00
25.00
2.50
5.00
5.00
SEEBURG Q160 of 1959 – 1960 (Continued)
A-1 PART #
74-010 Styli, T shaped, for original Pickering/Seeburg cartridges, (.7 mil
diamond tip for all stereo and mono. records), per pair
83-007 Springs for tone arm, hand made in the U.S.A., exact replacements, pair
78-010 Trip switch, Micro, for tone arm, (for Models B through APFEAI)
83-010 Balance spring for Micro trip switch, for tone arm, each one is hand made
in the U.S.A., Seeburg part # 245817, (for Models B through APFEAI)
83-011 Spring-for mechanism reversing switch, (Models B thru STD4), hand made
78-003 Trip coil for mechanism, Models V with 2050 for trip through DS, each
92-015 Capacitor, (run condenser), for mechanism motor, original style/metal can,
for M100A thru STD4, not SX100, for all USA motors, not for Nidec motors
78-024 Free Play Credit Unit, completely bypasses the original credit unit, for
Seeburg Models: L100, 101, Q100 & Q160, (This item is not discountable)
83-009 Carriage roller for mechanism, Seeburg part # 245082, each
88-020 Spray paint, Medium Blue, Models Q & AY, for inside cabinet, 12 oz. can
95-009 Graphics for mechanism ends, Silver, vinyl transfer, (for Model Q160 only),
“HIGH FIDELITY” and “SELECT-O-MATIC”, 2 piece set
73-060 Diffuser above front grill, (silk-screened, all blue, as original)
65-015 Speaker-board screen, (used in back of front metal grill screen), plastic fiber,
charcoal-black, for Seeburg Models 100J thru DS160, 36” X 30”
76-010 Key for cabinet sides and back door, (not cash door), F264
67-004 Cash bag, (duck cloth, as original, hand made in the U.S.A.)
67-012 Cash door, superior grade birch covered plywood, with backup plates,
(for use with metal frame around opening, Models C through LS3)
76-050 Lock, 1 1/8” quality lock, & 2 keys for Reproduction - wooden cash door
76-051 Lock, 1 1/8” quality lock, hardware, & 2 keys for Original metal cash door
76-058 Lock, 1 1/8” quality lock, hardware & 2 keys for lower back door
95-010 Graphic for rear upper cabinet, White, vinyl transfer,
(for Models Q100 and Q160 only), “SEEBURG”
95-011 Graphics for lower rear door, White, vinyl transfer,
(for Models Q100, and Q160 only), “MASTER VOLUME CONTROL”
and “MAIN SWITCH”, “RECORD REJECT”, 2 piece set
92-042 Capacitor kit: Seeburg Models 220, 222, Q100 & Q160, Amp. #: SHFA1,
includes schematics & replacement values reference sheet
92-043 Capacitor kit: Seeburg Q100 and Q160, using Amplifier # C1HFA1 or
C2HFA1, includes schematics & replacement values reference sheet
92-045 Capacitor kit: Seeburg Models 220, 222, Q100 & Q160, Amp. #: SHFA2,
includes schematics & replacement values reference sheet
91-004 Volume control pot. Models J/JL, V/VL, KS/KD, L100/101, Q & AY (mono.)
91-002 Volume control pot. (for stereo amplifiers): SHFA1, SHFA2 and TSA1
through TSA10, Also: Stereo Amps. in Rock-Ola Models 1460 through 437
92-053 Capacitor kit for TSU1 thru TSU7, Tormat Selector Units, in Seeburg Models
220 thru DS160, includes schematics & replacement values reference sheet,
(does not include the capacitor for the Stepper that operates wallboxes)
92-025 Capacitor for Stepper, operates wallboxes in Seeburgs: M100A thru LPC480
91-011 Knob, for volume control, round plastic, (amplifier must be removed to attach), has
two 5/64” Allen wrench screws, Seeburg AY100 thru LS3, (SHFA3 Thru TSA9)
91-012 Knob, for volume control, press-on, Seeburg AY100 thru LS3, (SHFA3 Thru TSA9)
72-001 Bulb, miniature #12, selection playing indicator (1) and
under mechanism cover logo (1), each
72-008 Bulb, miniature #55 (credit lamp) (1)
70-008 Fluorescent lamp 25 watt 28" T12, cool white is recommended, (2), each
70-009 Fluorescent lamp 25 watt 28" T12, daylight, optional color
- 52 -
$80.00
7.00
20.00
8.00
14.00
25.00
30.00
94.50
6.00
16.00
10.00
15.00
14.00
7.00
12.00
18.00
10.00
10.00
15.00
10.00
12.00
80.00
65.00
80.00
30.00
30.00
32.50
12.00
3.00
3.00
3.00
1.00
10.00
10.00
SEEBURG Q160 of 1959 – 1960 (Continued)
A-1 PART #
70-050 Colored sleeve for T12 fluorescent lamp, (cut to your specified length),
Specify: sleeve color: red, blue, green, yellow or pink, per foot
71-006 Ballast, 25 watt, for 1 lamp, new style, (clamped core), made in the U.S.A.
71-035 Ballast, 25 watt, for 1 lamp, original style case & Black color, (Now thermally
protected), made in the U.S.A., includes 2 rubber grommets for mounting
71-028 Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
71-030 Outlet, 3-wire grounded duplex receptacle, (The Receiver plugs into this)
$1.75
12.00
20.00
1.50
12.00
8.00
SEEBURG AY100, Y100 & AY100U 50 Records (100 Selections) and
AY160, Y160 & AY160U 80 Records (160 Selections)
manufactured 1960 – 1961
A-1 PART #
80-055 Service, Installation & Operation manual,
Seeburg Models AY100 & AY160, 186 pages, order R-273
80-056 Trouble Shooting Guide, Seeburg AY100 & AY160, 54 pages, order R-329
80-057 Seeburg AY100/AY160, purchase R-273 & R-329, save $10.00, order R-273A
30-001 Upper lid glass, AY100 &160 "Artist of the Week", (add $15 for pack & ship.)
73-062 Plastic Insert, “Seeburg” logo, printed red, for upper Artist of the Week lid glass
30-003 Upper lid glass, AY100 &160 “STEREOPHONIC”,
Replaces the “Artist of the Week” glass, (add $15 for packaging & shipping)
30-004 Lower lid glass AY100 (add $40 for pack. & ship. lower or both)
30-005 Lower lid glass AY160 (add $40 for pack. & ship. lower or both)
77-020 Make Any Selection glass, left side
77-022 Pricing glass, center, AY100/160 only, 10¢ per selection, Quarter 3 selections
77-023 Pricing glass, center, (for Models AY100 and AY160 only),
"Quarter 3 selections, 10¢ per selection, Half Dollar 7 selections”
77-017 Coins glass, right side
68-015 Coin reject plunger, plated, with scavenger wire, (Models G thru APFEAI)
83-006 Brushes, stylus-cleaning, double sided
78-012 Cam switch bank, 8 switches, for mechanism w/stereo, Seeburg #249463
84-015 Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
84-001 Motor coupler, connects mech. motor to gear, (replace if rubber is hard)
84-002 Motor support plug, rubber, for under mechanism motor
84-003 Mechanism turntable drive bushings, Seeburg part # 245464, pair
84-004 Mechanism frame rubber bumper, Seeburg part # 245291, pair
74-010 Styli, T shaped, for original Pickering/Seeburg cartridges, (.7 mil
diamond tip for all stereo and mono. records), per pair
83-007 Springs for tone arm, hand made in the U.S.A., exact replacements, pair
78-010 Trip switch, Micro, for tone arm, (for Models B through APFEAI)
83-010 Balance spring for Micro trip switch, for tone arm, each one is hand made
in the U.S.A., Seeburg part # 245817, (for Models B through APFEAI)
83-011 Spring for mechanism reversing switch, (Models B thru STD4), hand made
83-015 Spring, for original SP/ST – momentary slide, part of the service switch
83-017 Switch, SP/ST – momentary slide, part of the service switch, (AY thru SMC3)
78-003 Trip coil for mechanism, Models V with 2050 for trip through DS, each
92-015 Capacitor, (run condenser), for mechanism motor, original style/metal can,
for M100A thru STD4, not SX100, for all USA motors, not for Nidec motors
78-022 Free Play Credit Unit, completely bypasses the original credit unit, for
Seeburg Models: V200 with TSR3 receiver, VL200, KS & KD200, 161, 201,
220, 222, AY100, AY160, DS100 and DS160, (This item not discountable)
- 53 -
$45.00
30.00
65.00
125.00
10.00
125.00
140.00
135.00
10.00
15.00
15.00
10.00
25.00
12.00
15.00
25.00
25.00
2.50
5.00
5.00
80.00
7.00
20.00
8.00
14.00
6.00
6.00
25.00
30.00
94.50
SEEBURG AY100, Y100 & AY100U and AY160, Y160 & AY160U
manufactured 1960 – 1961 (Continued)
A-1 PART #
83-009
88-020
30-006
73-018
65-015
53-001
76-010
67-004
67-012
76-050
76-051
76-058
81-014
81-016
95-007
95-008
92-044
91-004
92-046
92-047
92-048
92-053
92-025
91-011
91-012
72-001
72-008
70-008
70-009
70-050
71-006
71-035
71-028
71-016
71-030
Carriage roller for mechanism, Seeburg part # 245082, each
Spray paint, Medium Blue, Models Q & AY, for inside cabinet, 12 oz. can
Medallion, round, Aluminum, for cabinet sides, original shape, printed, (2), ea.
Crown for front grill, original shape, but one color, not chromed (3), each
Speaker-board screen, (used in back of front metal grill screen), plastic fiber,
charcoal-black, for Seeburg Models 100J thru DS160, 36” X 30”
Kick plate, front – center, Stainless steel, Models AY and DS only
Key for cabinet sides and back door, (not cash door), F264
Cash bag, (duck cloth, as original, hand made in the U.S.A.)
Cash door, superior grade birch covered plywood, with backup plates,
(for use with metal frame around opening, Models C through LS3)
Lock, 1 1/8” quality lock, & 2 keys for Reproduction - wooden cash door
Lock, 1 1/8” quality lock, hardware, & 2 keys for Original metal cash door
Lock, 1 1/8” quality lock, hardware & 2 keys for lower back door
I.D. plate, Models: Q100 and Y100, (as original, Q or Y is not printed
on this I.D. plate), no serial number, for back of cabinet
I.D. plate, Model AY160U, (as original), no serial number, for back of cabinet
Graphic for rear upper cabinet, Silver, vinyl transfer, (for Models AY100,
AY160, DS100 and DS160 only), “SEEBURG”
Graphics for lower rear door, Silver, vinyl transfer, (AY & DS), “MASTER VOL.“
and “MAIN SWITCH”, “RECORD REJECT”, 2 piece set
Capacitor kit: Seeburgs: AY100/160 & Y100/160, using Amplifier # C1HFA2
or # C2HFA2, includes schematics & replacement values reference sheet
Volume control pot. Models J/JL, V/VL, KS/KD, L100/101, Q & AY (mono.)
Capacitor kit: Seeburgs, Any: AY, Y or AY-U Models using Amplifier #: SHFA3,
includes schematics & replacement values reference sheet
Capacitor kit: Seeburgs, Any: AY, Y or AY-U Models using Amplifier #: SHFA4,
includes schematics & replacement values reference sheet
Capacitor kit: Seeburg Models DS100 and DS160, using Amplifier #: SHFA5,
includes schematics & replacement values reference sheet
Capacitor kit for TSU1 thru TSU7, Tormat Selector Units, in Seeburg Models
220 thru DS160, includes schematics & replacement values reference sheet,
(does not include the capacitor for the Stepper that operates wallboxes)
Capacitor for Stepper, operates wallboxes in Seeburgs: M100A thru LPC480
Knob, for volume control, round plastic, (amplifier must be removed to attach), has
two 5/64” Allen wrench screws, Seeburg AY100 thru LS3, (SHFA3 Thru TSA9)
Knob, for volume control, press-on, Seeburg AY100 thru LS3, (SHFA3 Thru TSA9)
Bulb, miniature #12, selection playing indicator (1), and
under mechanism cover logo (2), each
Bulb, miniature #55 (credit lamp) (1)
Fluorescent lamp 25 watt 28" T12, cool white is recommended, (2), each
Fluorescent lamp 25 watt 28" T12, daylight, optional color
Colored sleeve for T12 fluorescent lamp, (cut to your specified length),
Specify: sleeve color: red, blue, green, yellow or pink, per foot
Ballast, 25 watt, for 1 lamp, new style, (clamped core), made in the U.S.A.
Ballast, 25 watt, for 1 lamp, original style case & Black color, (Now thermally
protected), made in the U.S.A., includes 2 rubber grommets for mounting
Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
Outlet, 3-wire grounded duplex receptacle, (The Receiver plugs into this)
- 54 -
$6.00
16.00
25.00
25.00
14.00
55.00
7.00
12.00
18.00
10.00
10.00
15.00
15.00
15.00
10.00
12.00
65.00
30.00
80.00
80.00
80.00
32.50
12.00
3.00
3.00
3.00
1.00
10.00
10.00
1.75
12.00
20.00
1.50
12.00
8.00
SEEBURG DS100 of 1961 – 1962 50 Records (100 Selections) and
DS160 of 1961 – 1962 80 Records (160 Selections)
A-1 PART #
80-058 Service & parts manual and Trouble Shooting charts, (all in one manual),
Seeburg Models DS100 and DS160, 216 pages, order R-299
31-002 Upper lid glass, DS100 &160 "Artist of the Week", (add $15 for pack & ship.)
73-064 Plastic Insert, “Seeburg” logo, printed blue, for upper Artist of the Week glass
31-004 Upper lid glass, DS100 & 160 “STEREOPHONIC”,
Replaces “Artist of the Week” glass, (add $15 for packaging & shipping)
31-005 Lower lid glass, DS 100, (add $40 for pack. & ship. lower or both)
31-006 Lower lid glass, DS 160, (add $40 for pack. & ship. lower or both)
77-020 Make Any Selection glass, left side
77-021 Pricing glass, center, (blue & black, for Models DS100 and DS160 only),
"Quarter 3 selections, 10¢ per selection, Half Dollar 7 selections”
77-017 Coins glass, right side
68-015 Coin reject plunger, plated, with scavenger wire, (Models G thru APFEAI)
83-006 Brushes, stylus-cleaning, double sided
78-012 Cam switch bank, 8 switches, for mechanism w/stereo, Seeburg #249463
84-015 Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
84-001 Motor coupler, connects mech. motor to gear, (replace if rubber is hard)
84-002 Motor support plug, rubber, for under mechanism motor
84-003 Mechanism turntable drive bushings, Seeburg part # 245464, pair
84-004 Mechanism frame rubber bumper, Seeburg part # 245291, pair
74-010 Styli, T shaped, for original Pickering/Seeburg cartridges, (.7 mil
diamond tip for all stereo and mono. records), per pair
83-007 Springs for tone arm, hand made in the U.S.A., exact replacements, pair
78-010 Trip switch, Micro, for tone arm, (for Models B through APFEAI)
83-010 Balance spring for Micro trip switch, for tone arm, each one is hand made
in the U.S.A., Seeburg part # 245817, (for Models B through APFEAI)
83-011 Spring for mechanism reversing switch, (Models B thru STD4), hand made
83-015 Spring, for original SP/ST – momentary slide, part of the service switch,
can be replaced without removing switch or re-soldering wires, (AY thru LS2)
83-017 Switch, SP/ST – momentary slide, part of the service switch, (AY thru SMC3)
78-003 Trip coil for mechanism, Models V with 2050 for trip through DS, each
92-015 Capacitor, (run condenser), for mechanism motor, original style/metal can,
for M100A thru STD4, not SX100, for all USA motors, not for Nidec motors
78-022 Free Play Credit Unit, completely bypasses the original credit unit, for
Seeburg Models: V200 with TSR3 receiver, VL200, KS & KD200, 161, 201,
220, 222, AY100, AY160, DS100 and DS160, (This item not discountable)
83-009 Carriage roller for mechanism, Seeburg part # 245082, each
73-018 Crown for front grill, original shape, but one color, not chromed (1)
65-015 Speaker-board screen, (used in back of front metal grill screen), plastic fiber,
charcoal-black, for Seeburg Models 100J thru DS160, 36” X 30”
53-001 Kick plate, front – center, Stainless steel, Models AY and DS only
76-010 Key for cabinet sides and back door, (not cash door), F264
67-004 Cash bag, (duck cloth, as original, hand made in the U.S.A.)
67-012 Cash door, superior grade birch covered plywood, with backup plates,
(for use with metal frame around opening, Models C through LS3)
76-050 Lock, 1 1/8” quality lock, & 2 keys for Reproduction - wooden cash door
76-051 Lock, 1 1/8” quality lock, hardware, & 2 keys for Original metal cash door
76-058 Lock, 1 1/8” quality lock, hardware & 2 keys for lower back door
95-007 Graphic for rear upper cabinet, Silver, vinyl transfer, (for Models AY100,
AY160, DS100 and DS160 only), “SEEBURG”
- 55 -
$46.50
125.00
10.00
125.00
140.00
135.00
10.00
15.00
10.00
25.00
12.00
15.00
25.00
25.00
2.50
5.00
5.00
80.00
7.00
20.00
8.00
14.00
6.00
6.00
25.00
30.00
94.50
6.00
25.00
14.00
55.00
7.00
12.00
18.00
10.00
10.00
15.00
10.00
SEEBURG DS100 and DS160 of 1961 – 1962 (Continued)
A-1 PART #
95-008 Graphics for lower rear door, Silver, vinyl transfer, (for Models AY100,
AY160, DS100 and DS160), “MASTER VOLUME CONTROL” and
“MAIN SWITCH”, “RECORD REJECT”, 2 piece set
92-048 Capacitor kit: Seeburg Models DS100 and DS160, using Amplifier #: SHFA5,
includes schematics & replacement values reference sheet
92-053 Capacitor kit for TSU1 thru TSU7, Tormat Selector Units, in Seeburg Models
220 thru DS160, includes schematics & replacement values reference sheet,
(does not include the capacitor for the Stepper that operates wallboxes)
92-025 Capacitor for Stepper, operates wallboxes in Seeburgs: M100A thru LPC480
91-011 Knob, for volume control, round plastic, (amplifier must be removed to attach), has
two 5/64” Allen wrench screws, Seeburg AY100 thru LS3, (SHFA3 Thru TSA9)
91-012 Knob, for volume control, press-on, Seeburg AY100 thru LS3, (SHFA3 Thru TSA9)
72-001 Bulb, miniature #12, selection playing indicator (1), and
under mechanism cover logo (2), each
72-008 Bulb, miniature #55 (credit lamp) (1)
70-008 Fluorescent lamp 25 watt 28" T12, cool white is recommended, (2), each
70-009 Fluorescent lamp 25 watt 28" T12, daylight, optional color
70-050 Colored sleeve for T12 fluorescent lamp, (cut to your specified length),
Specify: sleeve color: red, blue, green, yellow or pink, per foot
71-006 Ballast, 25 watt, for 1 lamp, new style, (clamped core), made in the U.S.A.
71-035 Ballast, 25 watt, for 1 lamp, original style case & Black color, (Now thermally
protected), made in the U.S.A., includes 2 rubber grommets for mounting
71-028 Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
71-030 Outlet, 3-wire grounded duplex receptacle, (The Receiver plugs into this)
$12.00
80.00
32.50
12.00
3.00
3.00
3.00
1.00
10.00
10.00
1.75
12.00
20.00
1.50
12.00
8.00
SEEBURG LPC1 of 1962 – 1964 and
LPC480 of 1964 – 1965
80 Records (160 Selections)
A-1 PART #
80-125 Service manual, Seeburg Model LPC1, 108 pages, order R-249
80-126 Installation, Operation & Trouble Shooting charts,
Seeburg Model LPC1, 76 pages, order R-255
80-127 Seeburg LPC1, purchase R-249 and R-255, save $9.00, order R-249A
80-130 Complete, all in one manual, Seeburg LPC480, 236 pages, order R-298
$37.50
33.00
61.50
48.95
73-045 Left keyboard Pricing, (albums: 1/2 Dollar or 2 Quarters per album / 10¢ per, Quarter 3,
1/2 Dollar 6 selections), plastic insert & clear glass, original colors for LPC1, (blue, red & blk.)
15.00
Other denominations of Left keyboard pricing inserts are available, please call
73-046 Right keyboard COINS, (NICKELS, DIMES, QUARTERS, HALF DOLLARS UP TO ONE DOLLAR
TOTAL), plastic insert & clear glass,
original colors for LPC1, (white, blue, red & black)
73-050 Seeburg models: LPC1 through LS2, labels for program holders,
(Letters and numbers, A1 thru V8), original font, peal and stick, 10 piece set
68-015 Coin reject plunger, plated, with scavenger wire, (Models G thru APFEAI)
83-006 Brushes, stylus-cleaning, double sided
84-015 Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
84-001 Motor coupler, connects mech. motor to gear, (replace if rubber is hard)
84-002 Motor support plug, rubber, for under mechanism motor
84-003 Mechanism turntable drive bushings, Seeburg part # 245464, pair
84-004 Mechanism frame rubber bumper, Seeburg part # 245291, pair
- 56 -
15.00
5.00
25.00
12.00
25.00
25.00
2.50
5.00
5.00
SEEBURG LPC1 of 1962 – 1964 & LPC480 of 1964 – 1965 (Continued)
A-1 PART #
74-010 Styli, T shaped, for original Pickering/Seeburg cartridges, (.7 mil
diamond tip for all stereo and mono. records), per pair
83-007 Springs for tone arm, hand made in the U.S.A., exact replacements, pair
78-010 Trip switch, Micro, for tone arm, (for Models B through APFEAI)
83-010 Balance spring for Micro trip switch, for tone arm, each one is hand made
in the U.S.A., Seeburg part # 245817, (for Models B through APFEAI)
83-011 Spring for mechanism reversing switch, (Models B thru STD4), hand made
83-015 Spring, for original SP/ST – momentary slide, part of the service switch,
can be replaced without removing switch or re-soldering wires, (AY thru LS2)
83-017 Switch, SP/ST – momentary slide, part of the service switch, (AY thru SMC3)
92-015 Capacitor, (run condenser), for mechanism motor, original style/metal can,
for M100A thru STD4, not SX100, for all USA motors, not for Nidec motors
78-026 Free Play Credit Unit, completely bypasses the original credit unit, for
Seeburg Models: LPC1, LPC1R & LPC480, (This item is not discountable)
78-030 Bakelite & metal latch lever for mechanism reversing relay, pictured on pgs.
2505 & 2506 in service manual, (new original stock), limited quantity
83-009 Carriage roller for mechanism, Seeburg part # 245082, each
65-002 Grill cloth, Specify: black or other color listed on page 74
under GRILL CLOTH, cloth size 30” X 40”, each
76-011 Key for cabinet sides, (not cash door), F278
67-012 Cash door, superior grade birch covered plywood, with backup plates,
(for use with metal frame around opening, Models C through LS3)
76-050 Lock, 1 1/8” quality lock, & 2 keys for Reproduction - wooden cash door
76-051 Lock, 1 1/8” quality lock, hardware, & 2 keys for Original metal cash door
92-058 Capacitor kits for Amplifiers used in Seeburg Models: LPC1 through
USC2, Specify: Amplifier # TSA1 through TSA10, each kit includes:
Schematics and replacement values reference sheet, each kit
92-019 Transistor, PNP germanium, for Seeburg TSA1 thru TSA10 Amplifiers,
Seeburg Auto Speed Units and Wurlitzer Amplifiers: 546 thru 553, each
91-002 Volume control pot. (for stereo amplifiers): SHFA1, SHFA2 and TSA1
through TSA10, Also: Stereo Amps. in Rock-Ola Models 1460 through 437
92-059 Capacitor kit for TCC1, used in Seeburg Models: LPC1 and LPC480,
includes Schematics and replacement values reference sheet
92-060 Capacitor kit for 45TASU1, used in Seeburg Models: LPC1 and LPC480,
includes Schematics and replacement values reference sheet
92-025 Capacitor for Stepper, operates wallboxes in Seeburgs: M100A thru LPC480
92-105 Capacitor for Auto-Speed units: Seeburg’s: LPC1/480, PFEAIU, APFEAI & SS160
91-011 Knob, for volume control, round plastic, (amplifier must be removed to attach), has
two 5/64” Allen wrench screws, Seeburg AY100 thru LS3, (SHFA3 Thru TSA9)
91-012 Knob, for volume control, press-on, Seeburg AY100 thru LS3, (SHFA3 Thru TSA9)
72-002 Bulb, for LPC1, miniature #19, (selection playing indicator), replaces
Seeburg original #15 bulb (1)
72-002 Bulb, for LPC480, miniature #19, (selection playing indicator), (2), each
72-008 Bulb, miniature #55 (credit lamps) (2), each
72-020 Bulb, some LPC480 models only, #93 (album facsimile pictures), (16), each
70-012 Fluorescent lamp 30 watt 36" T8, cool white is recommended (2)
70-050 Colored sleeve for T12 fluorescent lamp, (cut to your specified length),
Specify: sleeve color: red, blue, green, yellow or pink, per foot
71-008 Ballast 30 to 40 watt, for 1 lamp, (Thermally protected), made in the U.S.A.
71-010 Starter with condenser, FS-4, 30 to 40 watt, made in the U.S.A., each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
- 57 -
$80.00
7.00
20.00
8.00
14.00
6.00
6.00
30.00
104.50
20.00
6.00
16.00
7.00
18.00
10.00
10.00
75.00
10.00
30.00
35.00
37.00
12.00
12.00
3.00
3.00
2.50
2.50
1.00
2.50
10.00
1.75
30.00
1.50
12.00
SEEBURG PFEAIU “Electra” & APFEAI “Fleetwood” of 1965 – 1966
80 Records (160 Selections)
A-1 PART #
80-059
80-060
80-061
32-001
73-045
Service manual & parts list, PFEAIU & APFEAI, 108 pages, order R-268
Install., Operate. & Trouble guide, PFEAIU & APFEAI, 70 pages, order R-330
PFEAIU & APFEAI, purchase R-268 & R-330, save $9.00, order R-268A
Front glass, printed black & white street scene, (add $40 for pack. & ship.)
Left keyboard Pricing, (albums: 1/2 Dollar or 2 Quarters per album / 10¢ per, Quarter 3,
$37.00
33.00
61.00
75.00
1/2 Dollar 6 selections), plastic insert & clear glass, original colors for LPC1, (blue, red & blk.)
15.00
Other denominations of Left keyboard pricing inserts are available, please call
73-046 Right keyboard COINS, (NICKELS, DIMES, QUARTERS, HALF DOLLARS UP TO ONE DOLLAR
TOTAL), plastic insert & clear glass,
original colors for LPC1, (white, blue, red & black)
73-050 Seeburg models: LPC1 through LS2, labels for program holders,
(Letters and numbers, A1 thru V8), original font, peal and stick, 10 piece set
68-015 Coin reject plunger, plated, with scavenger wire, (Models G thru APFEAI)
83-006 Brushes, stylus-cleaning, double sided
84-015 Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
84-001 Motor coupler, connects mech. motor to gear, (replace if rubber is hard)
84-002 Motor support plug, rubber, for under mechanism motor
84-003 Mechanism turntable drive bushings, Seeburg part # 245464, pair
84-004 Mechanism frame rubber bumper, Seeburg part # 245291, pair
74-010 Styli, T shaped, for original Pickering/Seeburg cartridges, (.7 mil
diamond tip for all stereo and mono. records), per pair
83-007 Springs for tone arm, hand made in the U.S.A., exact replacements, pair
78-010 Trip switch, Micro, for tone arm, (for Models B through APFEAI)
83-010 Balance spring for Micro trip switch, for tone arm, each one is hand made
in the U.S.A., Seeburg part # 245817, (for Models B through APFEAI)
83-011 Spring for mechanism reversing switch, (Models B thru STD4), hand made
83-015 Spring, for original SP/ST – momentary slide, part of the service switch,
can be replaced without removing switch or re-soldering wires, (AY thru LS2)
83-017 Switch, SP/ST – momentary slide, part of the service switch, (AY thru SMC3)
92-015 Capacitor, (run condenser), for mechanism motor, original style/metal can,
for M100A thru STD4, not SX100, for all USA motors, not for Nidec motors
78-030 Bakelite & metal latch lever for mechanism reversing relay, pictured on pgs.
2505 & 2506 in service manual, (new original stock), limited quantity
83-009 Carriage roller for mechanism, Seeburg part # 245082, each
65-018 Grill cloth, 30" x 40", gray burlap, other colors of burlap
are listed on page 70 under GRILL CLOTH, 3 piece kit for these 2 models
76-013 Key for cabinet sides, (not cash door), F336
67-012 Cash door, superior grade birch covered plywood, with backup plates,
(for use with metal frame around opening, Models C through LS3)
76-050 Lock, 1 1/8” quality lock, & 2 keys for Reproduction - wooden cash door
76-051 Lock, 1 1/8” quality lock, hardware, & 2 keys for Original metal cash door
92-058 Capacitor kits for Amplifiers used in Seeburg Models: LPC1 through
USC2, Specify: Amplifier # TSA1 through TSA10, each kit includes:
Schematics and replacement values reference sheet, each kit
92-019 Transistor, PNP germanium, for Seeburg TSA1 thru TSA10 Amplifiers,
Seeburg Auto Speed Units and Wurlitzer Amplifiers: 546 thru 553, each
91-002 Volume control pot. (for stereo amplifiers): SHFA1, SHFA2 and TSA1
through TSA10, Also: Stereo Amps. in Rock-Ola Models 1460 through 437
92-061 Capacitor kit for SCC3 used in Seeburgs: PFEAIU and SS160, includes:
Schematics and replacement values reference sheet
- 58 -
15.00
5.00
25.00
12.00
25.00
25.00
2.50
5.00
5.00
80.00
7.00
20.00
8.00
14.00
6.00
6.00
30.00
20.00
6.00
16.00
7.00
18.00
10.00
10.00
75.00
10.00
30.00
32.50
SEEBURG PFEAIU “Electra and
APFEAI “Fleetwood” of 1965 – 1966 (Continued)
A-1 PART #
92-062 Capacitor kit for SCC4 used in Seeburg APFEAI, includes:
Schematics and replacement values reference sheet
92-063 Capacitor kit for 45TASU2 used in Seeburg Models: PFEAIU, APFEAI and
SS160, includes: Schematics and replacement values reference sheet
92-105 Capacitor for Auto-Speed units: Seeburg’s: LPC1/480, PFEAIU, APFEAI & SS160
91-011 Knob, for volume control, round plastic, (amplifier must be removed to attach), has
two 5/64” Allen wrench screws, Seeburg AY100 thru LS3, (SHFA3 Thru TSA9)
91-012 Knob, for volume control, press-on, Seeburg AY100 thru LS3, (SHFA3 Thru TSA9)
72-002 Bulb, miniature #19 (selection playing indicator) (2), each
72-008 Bulb, miniature #55 (credit lamps) (2), each
70-012 Fluorescent lamp 30 watt 36" T8, cool white is recommended (1)
70-014 Fluorescent lamp 30 watt 36" T8, black light bulbs are recommended (2), ea.
71-008 Ballast 30 to 40 watt, for 1 lamp, (Thermally protected), made in the U.S.A.
71-010 Starter with condenser, FS-4, 30 to 40 watt, made in the U.S.A., each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
$32.50
37.00
12.00
3.00
3.00
2.50
1.00
10.00
22.00
30.00
1.50
12.00
SEEBURG SS160 “Stereo Showcase” of 1966 – 1967
80 Records (160 Selections)
A-1 PART #
80-062
80-063
80-064
33-004
33-001
Service, Installation & Operation manual, SS160, 160 pages, order R-297
Trouble Shooting Guide, Seeburg SS160, 48 pages, order R-212
Seeburg SS160, purchase R-297 & R-212, save $10.00, order R-297A
Animation-motor for album display area, (new original stock), limited quantity
Front glass, all colors and graphics have been meticulously reproduced and
printed as original, Note: 17 different ink screens are used to manufacture
this part, (add $25 for packing, & shipping), (this item is not discountable)
33-002 Side glass, left side, shades of red, all colors and graphics are printed
as original, (this item is not discountable)
33-003 Side glass, right side, shades of blue, all colors and graphics are printed
as original, (this item is not discountable)
$40.00
28.00
58.00
65.00
175.00
50.00
50.00
73-045 Left keyboard Pricing, (albums: 1/2 Dollar or 2 Quarters per album / 10¢ per, Quarter 3,
1/2 Dollar 6 selections), plastic insert & clear glass, original colors for LPC1, (blue, red & blk.)
15.00
Other denominations of Left keyboard pricing inserts are available, please call
73-046 Right keyboard COINS, (NICKELS, DIMES, QUARTERS, HALF DOLLARS UP TO ONE DOLLAR
TOTAL), plastic insert & clear glass,
original colors for LPC1, (white, blue, red & black)
73-050 Seeburg models: LPC1 through LS2, labels for program holders,
(Letters and numbers, A1 thru V8), original font, peal and stick, 10 piece set
83-006 Brushes, stylus-cleaning, double sided
84-015 Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
84-001 Motor coupler, connects mech. motor to gear, (replace if rubber is hard)
84-002 Motor support plug, rubber, for under mechanism motor
84-003 Mechanism turntable drive bushings, Seeburg part # 245464, pair
84-004 Mechanism frame rubber bumper, Seeburg part # 245291, pair
74-008 Styli, wedge shaped, for all original Pickering/Seeburg cartridges including
#345-03D, (.7 mil diamond tip for all stereo and mono. records), per pair
83-008 Springs for tone arm, long “U” on one end, hand made in the U.S.A., pair
83-011 Spring for mechanism reversing switch, (Models B thru STD4), hand made
- 59 -
15.00
5.00
12.00
25.00
25.00
2.50
5.00
5.00
25.00
7.00
14.00
SEEBURG SS160 “Stereo Showcase” of 1966 – 1967 (Continued)
A-1 PART #
83-015 Spring, for original SP/ST – momentary slide, part of the service switch,
can be replaced without removing switch or re-soldering wires, (AY thru LS2)
83-017 Switch, SP/ST – momentary slide, part of the service switch, (AY thru SMC3)
92-015 Capacitor, (run condenser), for mechanism motor, original style/metal can,
for M100A thru STD4, not SX100, for all USA motors, not for Nidec motors
83-009 Carriage roller for mechanism, Seeburg part # 245082, each
76-013 Key for cabinet sides, (not cash door), F336
67-012 Cash door, superior grade birch covered plywood, with backup plates,
(for use with metal frame around opening, Models C through LS3)
76-050 Lock, 1 1/8” quality lock, & 2 keys for Reproduction - wooden cash door
76-051 Lock, 1 1/8” quality lock, hardware, & 2 keys for Original metal cash door
92-058 Capacitor kits for Amplifiers used in Seeburg Models: LPC1 through
USC2, Specify: Amplifier # TSA1 through TSA10, each kit includes:
Schematics and replacement values reference sheet, each kit
92-019 Transistor, PNP germanium, for Seeburg TSA1 thru TSA10 Amplifiers,
Seeburg Auto Speed Units and Wurlitzer Amplifiers: 546 thru 553, each
91-002 Volume control pot. (for stereo amplifiers): SHFA1, SHFA2 and TSA1
through TSA10, Also: Stereo Amps. in Rock-Ola Models 1460 through 437
92-061 Capacitor kit for SCC3 used in Seeburgs: PFEAIU and SS160, includes:
Schematics and replacement values reference sheet
92-063 Capacitor kit for 45TASU2 used in Seeburg Models: PFEAIU, APFEAI and
SS160, includes: Schematics and replacement values reference sheet
92-105 Capacitor for Auto-Speed units: Seeburg’s: LPC1/480, PFEAIU, APFEAI & SS160
91-011 Knob, for volume control, round plastic, (amplifier must be removed to attach), has
two 5/64” Allen wrench screws, Seeburg AY100 thru LS3, (SHFA3 Thru TSA9)
91-012 Knob, for volume control, press-on, Seeburg AY100 thru LS3, (SHFA3 Thru TSA9)
72-002 Bulb, miniature #19 (selection playing) (2) & (credit lamps, use 1 or both), each
72-007 Bulb, miniature #53 (illuminates the popularity meter area) (2), each
70-012 Fluorescent lamp 30 watt 36” T8, cool white is recommended (2), each
71-008 Ballast 30 to 40 watt, for 1 lamp, (Thermally protected), made in the U.S.A.
71-010 Starter with condenser, FS-4, 30 to 40 watt, made in the U.S.A., each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
$6.00
6.00
30.00
6.00
7.00
18.00
10.00
10.00
75.00
10.00
30.00
32.50
37.00
12.00
3.00
3.00
2.50
1.00
10.00
30.00
1.50
12.00
SEEBURG LS1 “Spectra” of 1967 – 1968 & LS2 “Gem” of 1968 – 1969
80 records (160 Selections)
A-1 PART #
80-065
80-066
80-067
80-068
80-069
80-070
34-001
34-002
73-050
83-006
84-015
Service, Installation & Operation manual, LS1, 154 pages, order R-320
Parts manual, Seeburg LS1, 42 pages, order R-331
Seeburg LS1, purchase R-320 and R-331, save $9.00, order R-320A
Service manual, Seeburg LS2, (Supplements the LS1 Service manual and
both are required for complete service to the LS2), 40 pages, order R-334
Installation, Operation & Parts catalog, Seeburg LS2, 102 pages, order R-332
Seeburg LS2, purchase R-320, R-334 & R-332, save $20.50, order R-334A
Front door glass, original pattern, includes white translucent plastic panels,
for LS1 only, pair, (add $20.00 for packing & shipping an oversize box)
Front door glass, original pattern, includes white translucent plastic panel,
for LS1 only, (add $20.00 for packing & shipping an oversize box), each
Seeburg models: LPC1 through LS2, labels for program holders,
(Letters and numbers, A1 thru V8), original font, peal and stick, 10 piece set
Brushes, stylus-cleaning, double sided
Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
- 60 -
$39.00
28.00
58.00
26.00
32.50
77.00
125.00
65.00
5.00
12.00
25.00
SEEBURG LS1 “Spectra” of 1967 – 1968 and
LS2 “Gem” of 1968 – 1969 (Continued)
A-1 PART #
84-001
84-002
84-003
84-004
74-008
83-008
83-011
83-015
83-017
92-015
83-009
34-003
76-014
67-012
76-050
76-051
92-058
92-019
91-002
92-064
92-065
91-011
91-012
72-002
70-020
70-022
70-012
71-001
71-008
71-028
71-010
71-016
Motor coupler, connects mech. motor to gear, (replace if rubber is hard)
Motor support plug, rubber, for under mechanism motor
Mechanism turntable drive bushings, Seeburg part # 245464, pair
Mechanism frame rubber bumper, Seeburg part # 245291, pair
Styli, wedge shaped, for all original Pickering/Seeburg cartridges including
#345-03D, (.7 mil diamond tip for all stereo and mono. records), per pair
Springs for tone arm, long “U” on one end, hand made in the U.S.A., pair
Spring for mechanism reversing switch, (Models B thru STD4), hand made
Spring, for original SP/ST – momentary slide, part of the service switch,
can be replaced without removing switch or re-soldering wires, (AY thru LS2)
Switch, SP/ST – momentary slide, part of the service switch, (AY thru SMC3)
Capacitor, (run condenser), for mechanism motor, original style/metal can,
for M100A thru STD4, not SX100, for all USA motors, not for Nidec motors
Carriage roller for mechanism, Seeburg part # 245082, each
Letter and number strips, indicate location of 45s in the record magazine,
peal & stick, 2 piece set
Key for cabinet sides, (not cash door), F205
Cash door, superior grade birch covered plywood, with backup plates,
(for use with metal frame around opening, Models C through LS3)
Lock, 1 1/8” quality lock, & 2 keys for Reproduction - wooden cash door
Lock, 1 1/8” quality lock, hardware, & 2 keys for Original metal cash door
Capacitor kits for Amplifiers used in Seeburg Models: LPC1 through
USC2, Specify: Amplifier # TSA1 through TSA10, each kit includes:
Schematics and replacement values reference sheet, each kit
Transistor, PNP germanium, for Seeburg TSA1 thru TSA10 Amplifiers,
Seeburg Auto Speed Units and Wurlitzer Amplifiers: 546 thru 553, each
Volume control pot. (for stereo amplifiers): SHFA1, SHFA2 and TSA1
through TSA10, Also: Stereo Amps. in Rock-Ola Models 1460 through 437
Capacitor kit for SCC7 used in Seeburg LS1, includes: Dummy plug for
by-pass of Auto Speed Unit, schematics & replacement values reference sheet
Capacitor kit for SCC8 used in Seeburg LS2, includes: Dummy plug for
by-pass of Auto Speed Unit, schematics & replacement values reference sheet
Knob, for volume control, round plastic, (amplifier must be removed to attach), has
two 5/64” Allen wrench screws, Seeburg AY100 thru LS3, (SHFA3 Thru TSA9)
Knob, for volume control, press-on, Seeburg AY100 thru LS3, (SHFA3 Thru TSA9)
Bulb, miniature #19 (digital selection display, 28 required), and
(credit window lamps) (1, 2 or all 3 can be used), each
Fluorescent lamp, UPPER, for Model LS1, (not for LS2) 18 watt 30” T8,
Note: Use either FS-U Starter, for 25 watts, with this lamp, cool white, (1)
Fluorescent lamp, UPPER, for Model LS2, (not for LS1) 18 Watt 24" T8,
Note: Use either FS-U Starter, for 25 watts, with this lamp, cool white, (1)
LS1 & LS2, Fluorescent lamp, LOWER, 30 watt 36” T8, cool white, (1)
Ballast 14 to 20 watt, for 1 lamp, new square style, clamped core, white, each
Ballast 30 to 40 watt, for 1 lamp, (Thermally protected), made in the U.S.A.
Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
Starter with condenser, FS-4, 30 to 40 watt, made in the U.S.A., each
Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
- 61 -
$25.00
2.50
5.00
5.00
25.00
7.00
14.00
6.00
6.00
30.00
6.00
5.00
7.00
18.00
10.00
10.00
75.00
10.00
30.00
30.00
30.00
3.00
3.00
2.50
9.00
7.00
10.00
12.00
30.00
1.50
1.50
12.00
SEEBURG LS3 “Apollo” of 1969 – 1970 Through
STD4 “Mardi-Gras” of 1977 – 1978 (160 Selection Models)
A-1 PART #
78-032
78-034
78-033
78-035
83-011
91-011
Digital receiver & decoder, (DRD1), Grey box, rebuilt, (with exchange)
Digital receiver & decoder, (DRD1), Grey box, rebuilt, (without exchange)
Digital transmitter & pricing unit, (DTP1), Black box, rebuilt, (with exchange)
Digital transmitter & pricing unit, (DTP1), Black box, rebuilt, (without exchange)
Spring for mechanism reversing switch, (Models B thru STD4), hand made
Knob, for volume control, round plastic, (amplifier must be removed to attach), has
two 5/64” Allen wrench screws, Seeburg AY100 thru LS3, (SHFA3 Thru TSA9)
91-012 Knob, for volume control, press-on, Seeburg AY100 thru LS3, (SHFA3 Thru TSA9)
$85.00
105.00
75.00
95.00
14.00
3.00
3.00
SEEBURG USC1 “Bandshell” of 1970 – 1971
80 records (160 Selections)
A-1 PART #
80-071
80-072
80-073
83-006
84-015
84-001
84-002
84-003
84-004
74-008
83-008
83-011
83-017
83-014
92-015
83-009
89-005
76-015
67-014
76-052
76-053
92-058
92-019
91-002
91-015
72-002
72-017
Service manual, Seeburg USC1 & USC2, 146 pages, order R-321
Parts manual, Seeburg USC1, 78 pages, order R-65
Seeburg USC1, Purchase R-321 and R-65, save $9.00, order R-321A
Brushes, stylus-cleaning, double sided
Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
Motor coupler, connects mech. motor to gear, (replace if rubber is hard)
Motor support plug, rubber, for under mechanism motor
Mechanism turntable drive bushings, Seeburg part # 245464, pair
Mechanism frame rubber bumper, Seeburg part # 245291, pair
Styli, wedge shaped, for all original Pickering/Seeburg cartridges including
#345-03D, (.7 mil diamond tip for all stereo and mono. records), per pair
Springs for tone arm, long “U” on one end, hand made in the U.S.A., pair
Spring for mechanism reversing switch, (Models B thru STD4), hand made
Switch, SP/ST – momentary slide, part of the service switch, (AY thru SMC3)
Contact lever assembly, Seeburg part # 10-252635, these make contact with,
and slide on, the Tormat memory unit, for USC1 thru STD4 (2 required), each
Capacitor, (run condenser), for mechanism motor, original style/metal can,
for M100A thru STD4, not SX100, for all USA motors, not for Nidec motors
Carriage roller for mechanism, Seeburg part # 245082, each
Letter and number strips, indicate location of 45s in the record magazine,
(160 selection Models only: LS3 through SMC3), peal & stick, 2 piece set
Key for cabinet sides, (not cash door), F291
Cash door, large, birch covered plywood, with backup plates
Lock, for Repro. wood cash door, for Models USC1 through SMC3,
7/8” quality lock, hardware, & 2 keys
Lock, for Original metal cash door, for Models USC1 through SMC3,
7/8” quality lock, hardware, & 2 keys
Capacitor kits for Amplifiers used in Seeburg Models: LPC1 through
USC2, Specify: Amplifier # TSA1 through TSA10, each kit includes:
Schematics and replacement values reference sheet, each kit
Transistor, PNP germanium, for Seeburg TSA1 thru TSA10 Amplifiers,
Seeburg Auto Speed Units and Wurlitzer Amplifiers: 546 thru 553, each
Volume control pot. (for stereo amplifiers): SHFA1, SHFA2 and TSA1
through TSA10, Also: Stereo Amps. in Rock-Ola Models 1460 through 437
Knob, press-on, for volume control, (for original potentiometer), in
Seeburg Models: USC1 thru SMC3, (For amplifiers: TSA10 thru SHP3)
Bulb, miniature #19 (digital selection display) (20 required), each
Bulb, miniature #1819 (instruction and credit window lamps) (6 total), ea.
- 62 -
$37.50
29.00
57.50
12.00
25.00
25.00
2.50
5.00
5.00
25.00
7.00
14.00
6.00
5.00
30.00
6.00
5.00
7.00
18.00
10.00
10.00
75.00
10.00
30.00
3.00
2.50
2.00
SEEBURG USC1 “Bandshell” of 1970 – 1971 (Continued)
A-1 PART #
70-012
70-013
71-008
71-010
71-016
Fluorescent lamp 30 watt 36” T8, cool white, CW or Day. can be used (3), each
Fluorescent lamp 30 watt 36” T8, daylight, CW or Day. can be used (3), each
Ballast 30 to 40 watt, for 1 lamp, (Thermally protected), made in the U.S.A.
Starter with condenser, FS-4, 30 to 40 watt, made in the U.S.A., each
Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
$10.00
10.00
30.00
1.50
12.00
SEEBURG USC2 “Bandshell Firestar” of 1971 – 1972
80 Records (160 Selections)
A-1 PART #
80-071 Service manual, Seeburg USC1 & USC2, 146 pages, order R-321
80-074 Service Supplement, Installation & Operation manual, Seeburg USC2,
(Supplements the USC1 Service manual R-321 and both are required
for complete service to the USC2), 110 pages, order R-336
80-075 Parts catalog, Seeburg USC2, 78 pages, order R-338
80-076 Seeburg USC2, purchase R-321, R-336 & R-338, save $28.00, order R-336A
80-084 USC2 Restoration Video, (VHS tape), running time 1 hr. 43 minutes
36-001 Record now playing indicator glass, left of selection keypad
36-002 Credits & Instruction glass, right of selection keypad
36-003 Printed plastic strips, (14 ½” W X 1 5/16” H), used in back of
record playing glass and credit & instruction glass, 4 piece set
36-004 Lid glass, (program title glass), has black printed border only,
(add $40 per order for packaging & shipping)
36-005 Front glass, original printed pattern, (add $40 for packaging & shipping)
36-006 Front printed plastic panel, (no additional pack. & ship. if sent with glass)
36-007 Side glass, left or right, each
36-008 Printed plastic panel, for left side glass, each
36-009 Printed plastic panel, for right side glass, each
83-006 Brushes, stylus-cleaning, double sided
84-015 Motor mounts, (round, metal & rubber rings); hold mechanism motor in place,
for all models using mechanism motors made in the U.S.A., 2 required, each
84-001 Motor coupler, connects mech. motor to gear, (replace if rubber is hard)
84-002 Motor support plug, rubber, for under mechanism motor
84-003 Mechanism turntable drive bushings, Seeburg part # 245464, pair
84-004 Mechanism frame rubber bumper, Seeburg part # 245291, pair
74-008 Styli, wedge shaped, for all original Pickering/Seeburg cartridges including
#345-03D, (.7 mil diamond tip for all stereo and mono. records), per pair
83-008 Springs for tone arm, long “U” on one end, hand made in the U.S.A., pair
83-011 Spring for mechanism reversing switch, (Models B thru STD4), hand made
83-017 Switch, SP/ST – momentary slide, part of the service switch, (AY thru SMC3)
83-014 Contact lever assembly, Seeburg part # 10-252635, these make contact with,
and slide on, the Tormat memory unit, for USC1 thru STD4 (2 required), each
92-015 Capacitor, (run condenser), for mechanism motor, original style/metal can,
for M100A thru STD4, not SX100, for all USA motors, not for Nidec motors
83-009 Carriage roller for mechanism, Seeburg part # 245082, each
89-005 Letter and number strips, indicate location of 45s in the record magazine,
(160 selection Models only: LS3 through SMC3), peal & stick, 2 piece set
76-015 Key for cabinet sides, (not cash door), F291
67-014 Cash door, large, birch covered plywood, with backup plates
76-052 Lock, for Repro. wood cash door, for Models USC1 through SMC3,
7/8” quality lock, hardware, & 2 keys
76-053 Lock, for Original metal cash door, for Models USC1 through SMC3,
7/8” quality lock, hardware, & 2 keys
- 63 -
$37.50
35.00
28.50
73.00
39.50
50.00
50.00
30.00
70.00
110.00
75.00
40.00
50.00
50.00
12.00
25.00
25.00
2.50
5.00
5.00
25.00
7.00
14.00
6.00
5.00
30.00
6.00
5.00
7.00
18.00
10.00
10.00
SEEBURG USC2 “Bandshell Firestar” of 1971 – 1972 (Continued)
A-1 PART #
92-058 Capacitor kits for Amplifiers used in Seeburg Models: LPC1 through
USC2, Specify: Amplifier # TSA1 through TSA10, each kit includes:
Schematics and replacement values reference sheet, each kit
92-019 Transistor, PNP germanium, for Seeburg TSA1 thru TSA10 Amplifiers,
Seeburg Auto Speed Units and Wurlitzer Amplifiers: 546 thru 553, each
91-002 Volume control pot. (for stereo amplifiers): SHFA1, SHFA2 and TSA1
through TSA10, Also: Stereo Amps. in Rock-Ola Models 1460 through 437
91-015 Knob, press-on, for volume control, (for original potentiometer), in
Seeburg Models: USC1 thru SMC3, (For amplifiers: TSA10 thru SHP3)
72-002 Bulb, miniature #19, (digital selection display) (20 required), each
72-017 Bulb, miniature #1819, (instruction and credit window lamps) (6 total), ea.
70-012 Fluorescent lamp 30 watt 36” T8, cool white, CW or Day. can be used (3), each
70-013 Fluorescent lamp 30 watt 36” T8, daylight, CW or Day. can be used (3), each
71-008 Ballast 30 to 40 watt, for 1 lamp, (Thermally protected), made in the U.S.A.
71-010 Starter with condenser, FS-4, 30 to 40 watt, made in the U.S.A., each
71-016 Line cord 16/3 round, black, 11½ feet, with 90° flat molded plug
$75.00
10.00
30.00
3.00
2.50
2.00
10.00
10.00
30.00
1.50
12.00
SEEBURG HARDWARE
NUTS, BOLTS, SCREWS, ETC. FOR SEEBURG JUKEBOXES
A-1 PART #
68-007 Seeburg A, B, BL and C Speed washers, round, hold letter/number strips
& title headings to program title holders. Also hold: 2 pc. Inst. glass;
SELECT glass & COINS glass, 55 pieces
68-016 Carriage bolt (1) & wing nut (1) for lower back door cover, for
Seeburg B thru VL, (3 pairs required), each pair
68-023 Seeburg B through VL and 201, shaft and 2 E washers,
prevents mechanism chassis from sliding, (2 required), each
68-046 Seeburg KS/KD200 through all newer, (not L100), chassis lock pin,
prevents mechanism chassis from sliding, (2 required), each
68-045 Seeburg B, BL, C, G & W, screws, mech. cover, top & side, stainless, per pair
68-017 Thumb screw, holds electrical selector in place, Seeburg B, BL & C, (4), each
68-035 Screws, stainless steel, for Seeburg stripper plate, Slotted head, set of 6
68-037 Screws, stainless steel, for Seeburg stripper plate, Phillips head, set of 6
68-019 Screw, stainless steel, slotted head, holds Seeburg redhead cartridge in
place, (1 required) & cartridge socket (1 required), each
68-025 Screw, stainless steel, Phillips head, holds Seeburg redhead cartridge in
place, (1 required) & cartridge socket (1 required), each
68-060 Screw, stainless steel, Phillips head, holds Pickering 345-03D cartridge
in place, (For 345-03D cartridge only and only 1 is required)
68-020 Screw, stainless steel, Phillips head, holds Stereo cartridge (1) &
cartridge socket (1), for Seeburg models: 220 through PFEAIU only, each
68-040 Screws with lock washers, hold metal frame for record now playing indicator
to record magazine frame, Seeburg B thru JL, Slotted head, set of 4
68-042 Screws with lock washers, hold metal frame for record now playing indicator
to record magazine frame, Seeburg B thru JL, Phillips head, set of 4
68-022 Screw, Phillips, for Seeburg G and W near cabinet dome locks, (2), each
68-050 Barrel screw, holds left side of Mech. cover at correct height, for Seeburg
Models: R, J, JL, KS/KD200, L100, 101, 161, 201, 220 & 222, slotted head
68-051 Barrel screw, holds left side of Mech. cover at correct height, for Seeburg
Models: R, J, JL, KS/KD200, L100, 101, 161, 201, 220 & 222, Phillips head
68-024 Seeburg Q & Up, Screw for top of metal mechanism cover
68-026 Seeburg A thru VL200, Machine screws, Phillips head, hold Amplifier &
Receiver in place on lower back door, (4) 1” & (4) ½”, 65¢ ea. or 8 piece set
- 64 -
$8.00
1.50
6.00
4.50
1.50
1.50
1.50
1.50
1.50
1.00
1.50
1.50
2.00
2.00
1.00
7.00
9.00
2.00
5.00
SEEBURG KEYS (For Original Locks), for cabinet sides and
Models with back doors, (not for cash door locks)
FOR MODEL
KEY #
PRICE
A-1 PART #
76-001 Volume control key:
for original potentiometers, (All Seeburg Amps. thru SHFA2 & all Wurlitzer’s)
76-002 Key, Seeburg 146, 147, 148: Lid
L7380
76-003 Key, Seeburg 146, 147, 148: Door
L7325
76-004 Key, Seeburg M100A, M100B, M100BL, (not for cash door locks)
G219
76-005 Key, Seeburg M100C, (not for cash door locks)
G245
76-006 Key, Seeburg HF100G, W100, (not for cash door locks)
F221
76-007 Key, Seeburg HF100R, 100J, 100JL, (not for cash door locks)
F279
76-008 Key, Seeburg V200, VL200, (not for cash door locks)
F314
76-009 Key, Seeburg KS/KD200, L100, 101, 161, 201, (not for cash door locks) F313
76-010 Key, Seeburg 220, 222, AQ100/160, AY100/160, DS100/160
F264
76-011 Key, Seeburg LPC1, LPC480, (not for cash door locks)
F278
76-012 Key, Seeburg U100 (Mustang), (not for cash door locks)
F330
76-013 Key, Seeburg PFEA1U (Electra), APFEA1 (Fleetwood) and
SS160 (Showcase), (not for cash door locks)
F336
76-014 Key, Seeburg S100 (Phonojet), LS1 (Spectra), LS2 (Gem),
LS3 and SE100, (not for cash door locks)
F205
76-015 Key, Seeburg USC1 (Bandshell) and USC2 (Firestar)
F291
76-016 Key, Seeburg SX-100, SPS160, SPS2, FC1, SL100, SQS160,
STD160, SB100, STD2, STD3, 100-77D, FC2, 100-78D and
STD4, Key for Cabinet and back door, (not for cash door locks)
F293
76-017 Key, Seeburg SMC1 (Disco 160) and SMC2 (Phoenix)
S102
76-018 Key, Seeburg VMC1 (Video Music) and SMC3 (Prelude)
F333
76-019 Keys, Seeburg master set, 17 cut keys & 1 volume control key, (Save $23.00)
$3.00
10.00
10.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
105.00
We stock original and replacement Locks and keys for Seeburg wallboxes,
(For Seeburg wallbox lock information, please see page 65).
SEEBURG MECHANISM MOTORS &
SELECTOR COIL ARMATURE ASSEMBLIES,
(a/k/a Pin Banks or Pin Cages)
A-1 PART #
84-016 Motor for mechanism, Bodine, 4 wire leads, used, tested, guaranteed
84-020 Selector Coil & Armature Assembly, (a/k/a: Pin Bank), (Completely
dissembled & rebuilt, 100% Guaranteed, “A quality restoration”). Immediate
delivery is available. An exchange is required: Customer must send a
Pin Bank that is in good, original, condition, (In other words, one that can be
rebuilt and is not damaged), Specify: M100B/BL, M100C, HF100G, W100,
HF100R, 100J or 100JL, each
SEEBURG SPRAY PAINTS
“Seeburg paints” are custom formulated using high quality acrylic enamel.
(All spray paint cans contain between 10.5 ounces and 12 ounces).
Please note: Spray Paint can be shipped within the USA via UPS Ground only.
For Security & safety reasons, we will not ship Spray Paint via air transportation.
Spray Paints for Seeburg Jukeboxes are listed on the next page
- 65 -
$125.00
195.00
SPRAY PAINTS FOR SEEBURG JUKEBOXES
A-1 PART #
88-006 Spray paint, “Seeburg Yellow”, for Model M100C, for mechanism frame
and most of the other mechanism parts, acrylic enamel, 10.5 oz. can
88-007 Spray paint, “Seeburg Aqua/Blue”, for Model M100C, for mechanism cover
and base of mechanism, acrylic enamel, 10.5 oz. can
88-008 Spray paint, Red, for Model G magazine and mechanism frame, also for
Model W entire mech. except for mech. cover, acrylic enamel, 12 oz. can
88-009 Spray paint, Dark Blue, for HF100G & W100, for metal grill on front, 12 oz. can
88-010 Spray paint, Light Blue, Model G, for mechanism cover,
mechanism end caps, etc., acrylic enamel, 12 oz. can
88-017 Spray paint, Burnt Orange, for Models 161/201, acrylic enamel, 12 oz. can
88-018 Spray paint, Aqua, for Models 161/201, acrylic enamel, 12 oz. can
88-020 Spray paint, Medium Blue, Models Q & AY, for inside cabinet, 12 oz. can
$16.00
16.00
16.00
16.00
16.00
16.00
16.00
16.00
SEEBURG SPEAKERS & SPEAKER PARTS
A-1 PART #
82-004 Grill, musical note-shaped, mirror polished stainless steel for front of
original or reproduction, large teardrop-mirrored speaker, (18 1/8” H X 12” W)
82-002 Mirrors for large teardrop-mirrored speaker, blue glass, (161 1” squares)
82-005 “Seeburg” printed on 1” square blue glass mirrors for large teardrop-mirrored
speaker, (these printed mirrors are not included with the above mirror set)
82-003 Seeburg Logo for Small Teardrop Spkr., polished Zinc, w/2 speed washers
82-006 Line matching transformer for Speakers w/constant voltage, 10 watt, 70.7 volt
77-055 Mirror kit for KLEERTONE: Musical Note Front & Model 125 speakers,
Blue mirrors, (92 pieces, 2” X ½”), for speaker cabinet
$60.00
65.00
35.00
50.00
9.00
55.00
SEEBURG WALL-O-MATIC and CONSOLETTE WALLBOXES
A-1 PART #
80-121
37-015
80-077
80-078
80-115
37-020
37-001
37-018
37-016
37-002
37-021
37-022
37-003
37-004
37-005
37-006
37-150
37-007
37-013
37-012
76-060
37-008
Manual, for pre-war Seeburg wallboxes, 148 pages, order R-301
Front glass, printed, (shows pricing), for 1940 Seeburg Bar-0-Matic
Manual, 3W-1 & 3W-1D wallboxes, 24 pages, order R-328
Manual, wallboxes: 200 and 160 play & type 3W100, 56 pages, order R-168
Manual, wallboxes, stereo Consolette models SCI and SCII, 48 pgs, R-317
Program window, original, curved GLASS, with original logo for 3W-1 only
Program window, curved plastic, printed as original, for 3W-1 only
Program window, curved plastic, printed as original, for 160 select models
Program window, curved plastic, printed as original, for 3WA, 200 models
Instruction plate, (metal), original shape & printed as original, for 3W-1 only,
(A-1 part # 37-002 is out of stock until February 2011)
Foil, peel and stick cover for Instruction plate, printed as original, 3W-1 only
Foil, peel & stick cover for Instruction plate, printed as original, 160 & 200 only
Select lens for instruction plate, green plastic, original shape, for 3W-1 only
Coin entry glass, COINS, 6 PLAYS – QUARTER, etc., w/red felt backer, for 3W-1
Coin entry glass, 10¢/25¢, 3 PLAYS QUARTER, etc., w/red felt backer, for 3W-1
Coin entry glass, 25¢, 1 PLAY – QUARTER, with red felt backer, for 3W-1 only
Red felt backer only, pre-cut, for A-1 # 37-004, 37-005 & 37-006, each
Springs for pages, fits 3W-1 and 3W-100 models, (2 required), per pair
Spring for pages, fits 160 and 200 selection models, (1 required)
Plastic instruction plate, “Turn pages to view entire program”, for
160 and 200 selection wall boxes only
Lock, original lock, one key, barrel nut and roll pin, for 3W-1 wallboxes
Plug, 3 prong w/lock arms for connecting wall boxes to selection receivers
- 66 -
$38.00
20.00
20.00
27.00
27.00
30.00
25.00
35.00
35.00
20.00
9.00
9.00
9.00
9.00
9.00
9.00
.35
9.00
4.00
15.00
16.50
10.50
SEEBURG WALL-O-MATIC and
CONSOLETTE WALLBOXES (Continued)
A-1 PART #
37-010 Socket, 3 prong w/lock arms, to splice cable at any point using 3 prong plug
37-011 Socket, 3 prong panel mount for wired selection receivers,
(this socket receives A-1 Part # 37-008)
37-009 Fuse, 3 amp or 3 2/10 amp Fustat, large screw in type, for Seeburg: M100A
thru VL200 Selection Receivers, (these are for the operation of wallboxes)
72-006 Bulb, miniature #51 (above pages and under select window) (3), each
72-008 Bulb, miniature #55 (coin entry and push buttons) (3), each
$9.00
6.00
8.00
1.00
1.00
We stock original Locks and keys for Seeburg wallboxes.
To order a key for an original Seeburg wallbox lock, please Specify: the
“S” Key number, (a three digit number), on the face of the original lock.
Keys for original Seeburg wallbox locks are $12.00 each.
FOR SEEBURG JUKEBOXES, WE STOCK: SERVICE MANUALS,
TROUBLE SHOOTING GUIDES, PARTS LISTS, MINI BULBS, CARTRIDGES,
STYLI, (NEEDLES), FLUORESCENT LAMPS, KEYS FOR CABINET LOCKS,
CREDIT UNIT ADAPTERS & REPLACEMENT CREDIT UNITS FOR MOST
SEEBURG MODELS. Please Call or Email for details and pricing.
WURLITZER
WURLITZER KEYBOARD BUTTON SETS (Information about)
Exact reproductions, BEAUTIFUL! For Models: 1700, 2000, 2100, 2200, 2204,
2300, 2304, and 2310. All Letters & Numbers are heat stamped onto each button,
as original and each clear cap is pre-set during production.
(Each button is meticulously, hand made, in the U.S.A.)
Please note: All exact reproduction “Wurlitzer Keyboard Button Sets” are in
limited supply. Also, Wurlitzer Keyboard button sets are not discountable.
WURLITZER KEYBOARD BUTTON SETS
A-1 PART #
96-060
96-061
96-063
96-064
96-065
96-066
96-067
Wurlitzer Model 1700, Keyboard buttons, complete 30 piece set
Wurlitzer Model 1700, Keyboard buttons, Maroon-Red (26), each
Wurlitzer Models 2000 and 2100, Keyboard buttons, complete 30 piece set
Wurlitzer Models 2200 and 2300, Keyboard buttons, complete 30 piece set
Wurlitzer Models 2204 and 2304, Keyboard buttons, complete 30 piece set
Wurlitzer Model 2310, Keyboard buttons, complete 20 piece set
Wurlitzer Models 1700, 1800, 1900 & 2104, Large square keyboard buttons,
(A, B, C and D only), 4 piece set
96-003 Wurlitzer Models 3100 and 3200, Keyboard button, (New, old stock),
Original red color, with metal insert, limited quantity, each
$130.00
6.00
150.00
150.00
150.00
120.00
75.00
4.00
MISCELLANEOUS WURLITZER PARTS
A-1 PART #
96-032
96-014
96-033
96-040
65-003
Model 750 wooden caster blocks, each
Model 800 front door center amber plastic, resin molded, exact reproduction
Model 850 wooded caster blocks, each
Model 1015 Floor, (add $30 for packaging & shipping)
Foil, embossed, gold, ½” pillowed squares, for interior of Seeburg C,
Wurlitzer 1080 & 1100, 32” X 16” sheet, (2 sheets required), per sheet
- 67 -
$12.00
160.00
10.00
90.00
40.00
MISCELLANEOUS WURLITZER PARTS (Continued)
A-1 PART #
72-012
96-045
96-016
96-019
96-020
92-018
91-005
76-001
96-034
96-035
96-037
91-006
96-070
92-019
92-020
96-005
96-006
96-007
96-008
96-009
96-050
96-051
96-052
Bulb, miniature #87, 6.8 volt, Wurlitzer 1100 Arch, each
1100 Lower cabinet plastics, beautiful 4 piece set, (Not discountable)
1250 Light diffusers for above program holders, white plastic, 3 piece set
1250 Program title glass, numbers printed as original, 3 piece set
1250 Color sheet, front of mech. 22” W x 2 ½“ H, green, red, purple & yellow
Bridge rectifier, 15 amps. 200 volts, 4 posts, w/mounting hole, a must
replacement part for power supplies in Wurlitzer: 1500, 1550 & 1700 – 2400
Volume control pot. for Models 1400, 1500, 1600, 1700 & 1800
Volume control key for original pots., (Seeburg amps. thru SHFA2 & all Wurlitzer’s)
Model 1800 Floor, (Not discountable), (add $30 for packaging & shipping)
Model 1800 Speaker baffle board, (add $35 for packaging & shipping)
Decal, Centennial, 1856-1956, for Models 1900 & 2000
Volume control pot. for Models 1900 through 2400 (mono.)
Front glass for 2700 & 2710, “Wurlitzer Stereo”, N.O.S., limited quantity, ea.
Transistor, PNP germanium, for Seeburg TSA1 thru TSA10 Amplifiers,
Seeburg Auto Speed Units and Wurlitzer Amplifiers: 546 thru 553, each
Transistor, NPN silicon, for Seeburg SHP Amplifiers
& Wurlitzer 556 Amplifiers, each
Drive belt for turntable motor, Models: 1700 through 2500, each
Drive belt for turntable motor, Models: 2600 and 2610 only, each
Drive belt for turntable motor, Models: 2700 and 2800, each
Drive belt for turntable motor, series:
2900 through 3300, one size fits both pulleys, 2 required, each
Drive belt for turntable motor, series: 3400 through 3800,
7500 & 1050, one size fits both pulleys, 2 required, each
Model 1050 Pilaster plastic, left side
Model 1050 Pilaster plastic, right side
Model 1050 Pilaster plastics, per pair
$2.00
495.00
18.00
30.00
15.00
8.00
30.00
3.00
100.00
180.00
10.00
30.00
75.00
10.00
5.00
5.00
5.00
5.00
5.00
5.00
115.00
115.00
200.00
GROMMETS AND MOUNTS FOR WURLITZER TURNTABLE MOTORS
Note: Concerning replacement Grommets and Mounts for Turntable motors
in Wurlitzer Models 1700 and newer:
Wurlitzer Models 1700 thru early 2800: Turntable motors in these models
take 2 mounts above the motor and 2 grommets below the motor.
Wurlitzer Models Late 2800 thru 3300: Turntable motors in these models
take 3 mounts, (2 above the motor and one below the motor).
Wurlitzer Models 3400 thru 3800, 1050 & 7500: Turntable motors in these
models take 4 mounts and no grommets.
A-1 PART #
96-057 Wurlitzer turntable motor mounts, #60882, each
96-058 Wurlitzer turntable motor grommets #49884, each
Keys for Wurlitzer Jukebox cabinets,
(Not for cash door locks, are listed on the next page)
- 68 -
$6.00
3.00
WURLITZER KEYS (For Original Locks), for cabinet sides and
Models with back doors, (not for cash door locks)
FOR MODEL
KEY #
PRICE
A-1 PART #
76-001 Volume control key:
for original potentiometers, (All Seeburg Amps. thru SHFA2 & all Wurlitzer’s)
76-025 Key, Wurlitzer 41, 71, 81
TF25
76-026 Keys, Wurlitzer 700, 800 and 780, (2 keys required), TF25 & LF50, for both
76-027 Key, Wurlitzer 750, 850 and 950
LF50
76-028 Key, Wurlitzer 1015, 1080, 1100 and 1250
RW 75
76-029 Key, Wurlitzer 1400 and 1450
RW 44
76-030 Key, Wurlitzer 1500 and 1550
RW 47
76-031 Key, Wurlitzer 1500A, 1550A, 1600 and 1650
RW 49
76-032 Key, Wurlitzer 1600A and 1650A
RW 85
76-033 Key, Wurlitzer 1700 and 1700HF
RW 80
76-034 Key, Wurlitzer all Models from 1800 through 2410
RW 90
76-035 Key, Wurlitzer all Models from 2500 through 3010
RW 95
76-036 Key, Wurlitzer 3100 and 3200
RW100
76-037 Key, Wurlitzer 3300 and 3400
RW105
76-038 Key, Wurlitzer 3500, 3600, 3700, 7500, all 3800 and 1050
RW110
76-039 Key, Wurlitzer One More Time, (Reproduction 1015)
WUA 1
76-040 Key, Wurlitzer New York, NY & other CD models, (not OMT)
WUA 2
$3.00
7.00
12.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
7.00
WURLITZER MOUNTING BOARDS FOR MECHANISMS
A-1 PART #
Please note: Wurlitzer Mounting Boards for Mechanisms are not discountable
96-021
96-027
96-028
96-026
96-029
Mech. board 600 Rotary w/walnut veneer (add $30 for pack. & ship.)
Mech. board Victory 600 Rotary w/walnut veneer (add $30 for pack. & ship.)
Mech. board Victory 600 Keyboard w/walnut veneer (+ $30 for pack. & ship.)
Mech. board 800 with walnut veneer (add $30 for packaging & shipping)
Mech. board 850 with walnut veneer (add $30 for packaging & shipping)
$110.00
130.00
130.00
125.00
125.00
FOR WURLITZER JUKEBOXES
WE STOCK: SERVICE MANUALS, TROUBLE SHOOTING GUIDES,
PARTS LISTS, MINI BULBS, CARTRIDGES, STYLI – (NEEDLES),
FLUORESCENT LAMPS, AND KEYS, (FOR ORIGINAL CABINET LOCKS),
FOR MOST MODELS
Please Call or Email for details and pricing.
BOOKS, JUKEBOX HISTORY BOOKS
A-1 PART #
80-079 History book, AMi Jukeboxes, Includes: The pre Jukebox era; Early AMi
Jukebox, with text, photos and other data on Ami and Rowe Jukeboxes
from 1938 through 1989, 176 pages
$35.00
80-081 History book, Seeburg Jukeboxes, Includes: 62 years of fun 1927 – 1989;
The pre Seeburg Jukebox era; Jukeboxes by Seeburg and others 1927-1933;
Special features in Jukeboxes and wall boxes and Ready reference data for
Seeburg Jukebox Models A of 1948 through SCDI of 1986-87, 142 pages
35.00
80-082 History book, Wurlitzer Jukeboxes, Includes: Chronology of Wurlitzer Jukeboxes
1934 through 1974; Early history of Wurlitzer; Photos and data on Wurlitzer
Jukeboxes, and remote equipment; Jukeboxes by Wurlitzer Of West Germany
and Deutsche Wurlitzer including the “One More Time”, 224 pages
- 69 -
35.00
BOOKS, JUKEBOX HISTORY BOOKS (Continued)
A-1 PART #
80-083 History Book, Obscure Jukeboxes, Volume 1, also by Frank Adams, Includes:
Edison Phonographs, Regina Music Boxes and rare Jukeboxes manufactured by
Mills, Aireon, United, Ristaucrat and a host of other American manufacturers from
1889 through 1993. Mostly black & white pictures, some in full color, 182 pages
$24.50
80-085 Restoring the Seeburg “C”, detailed instructions with pictures, 64 pages
22.50
80-086 Mechanical restoration guide for 50s Seeburg Jukeboxes, 36 pages
15.00
BULBS, INCANDESCENT, (LIGHT BULBS)
A-1 PART #
72-025 Light bulbs, 7½ watts, standard base, long life,
Specify: clear, orange or white, each
72-026 Light bulb, 11 watts, frosted, standard base, long life, each
72-027 Light bulbs, 11 watts, standard base, long life, Specify: translucent red,
translucent amber, translucent blue, translucent yellow, translucent green, each
72-028 Light bulb, 15 watts, standard base, long life, Specify: clear or frosted, each
$2.50
2.50
2.50
2.00
BULBS, MINIATURE
A-1 PART #
72-001 Bulb, miniature #12, (2 prong), 6.3 volt, Late 50’s/Early 60’s Seeburgs, ea.
72-002 Bulb, miniature #19, (2 prong), 14.4 volt, for 12 volt applications, 1971 & up
Seeburgs, (digital selection indicators & Consolette wallboxes), each
72-021 Bulb, miniature #37, 14 volt, (wedge base), Rock-Ola 490-1, each
72-003 Bulb, miniature #44, 6.3 volt, for Rock-Ola, Seeburg & Wurlitzer, each
72-004 Bulb, miniature #47, 6.3 volt, for Rock-Ola, Seeburg & Wurlitzer, each
72-006 Bulb, miniature #51, 7.5 volt, Seeburg 146/147/148 selection dial &
Seeburg wallboxes, & Wurlitzer 2000 & 2100, (n.o.s. Westinghouse), each
72-007 Bulb, miniature #53, 14.4 volt, Seeburg & Rock-Ola, (n.o.s., Westinghouse), ea.
72-008 Bulb, miniature #55, 7 volt, each
72-010 Bulb, miniature #63, 7 volt, 50s Seeburgs, each
72-009 Bulb, miniature #73, 14.4 volt, (SMC3 Decorative lamps), each
72-019 Bulb, miniature #74, 14 volt, some Rock-Ola Models, each
72-011 Bulb, miniature #81, 6.5 volt, Rock-Ola 1478 thru 1485,
Seeburg 146/147/148 behind plastics, and 50s Seeburgs, each
72-012 Bulb, miniature #87, 6.8 volt, Wurlitzer 1100 Arch, each
72-020 Bulb, #93, 12.8 volt, some Seeburg LPC480 models only, these illuminate
album facsimile pictures located above curved program glass, (16), each
72-014 Bulb, miniature #313, 28 volt, Use bulb # 1819 (A-1 Part # 72-017),
for Rock-Ola 1422/26/28, (Thank You lamp), ea.
72-015 Bulb, miniature #455, 6.5 volt Flasher,
(new original stock, Westinghouse, best quality), each
72-016 Bulb, miniature #656, 28 volt, (for newer Seeburg Models starting with the
1972 SPS160 Olympian), (Credit, Coins, etc.), each
72-017 Bulb, miniature #1819, 28 volt, Seeburgs: LS3; USC1; USC2, each
72-005 Bulb, miniature #1847, 6.3 volt, (longer lasting, replaces #47 bulb), each
72-018 Bulb, miniature #2182D, 14 volt, (2 wire), Seeburg: STD2, 3 & 4, ea.
Cartridges & Needles, (Replacement Styli), are listed on the next two pages
- 70 -
$3.00
2.50
1.00
1.00
1.00
1.00
1.00
1.00
1.50
1.00
1.00
2.00
2.00
2.50
2.00
2.00
1.00
2.00
1.50
1.00
CARTRIDGES & NEEDLES
Please note: All Cartridges listed in this catalog, are the Very best
quality available. We do not sell inferior products.
A-1 PART #
75-003 Cartridges, Pickering NP/AC magnetic, stereo, excellent replacement for
AMi I, J (Stereo), K, Lyric, Continental I & II, L, M, N, O & MM1 & up,
Rock-Ola 424, 425, 426, 429, 433, 436, 437, 440, 442, 444 & 446 thru 490-2,
Wurlitzer OMT 45s & other Models requiring a magnetic stereo cartridge,
(this cartridge can also be used for all 45 rpm mono. jukeboxes requiring a
magnetic cartridge by wiring both channels & grounds across on the cartridge)
$40.00
75-001 Cartridge, # P-132D ceramic, stereo, for Rock-Ola 1468
through 1485, 1493 thru 418, 430, 431, 432, 434, 435, 441, 443, 445,
Wurlitzer (Stereo only) 2300 through 3800, 7500 & 1050,
(this cartridge can also be used for all 45 rpm mono. jukeboxes requiring a
ceramic cartridge by wiring both channels & grounds across on the cartridge)
22.50
NEEDLES, (REPLACEMENT STYLI)
Please note: All Needles, (Replacement Styli), listed in this catalog, are the
Very best quality available. We do not sell inferior products.
A-1 PART #
74-015 Needles, (Styli), for original Seeburg Blackhead cartridge,
(.7 mil diamond tip for all 45 rpm stereo and mono. records), per pair
74-027 Styli, for original Seeburg Blackhead cartridge,
(3 mil sapphire tip for original 78 rpm records), per pair
74-025 Styli, .7 mil diamond tip, forked base, (a screw holds each stylus in place),
for Varco cartridges, (early Seeburg conversion cartridges), per pair
74-009 Styli, replaces Astatic SE100-7D, for original Pickering/Seeburg
Hi-Fi magnetic, redhead cartridges used in Models M100B thru 201,
(.7 mil diamond tip for all 45 rpm stereo and mono. records), per pair
74-010 Styli, T shaped, replace Astatic SE102-7D, for original
Pickering/Seeburg cartridges used in Models 220 thru PFEAIU,
(.7 mil diamond tip for all 45 rpm stereo and mono. records), per pair
74-008 Styli, wedge shaped, replaces Astatic SE103-7D, for all Pickering/Seeburg
cartridges used in Models SS160 and newer, Also for Pickering/Seeburg
cartridge # 345-03D used in Models M100B thru 201,
(.7 mil diamond tip for all 45 rpm stereo and mono. records), per pair
74-017 Styli, Astatic N2-SD, .7 mil diamond & .7 mil sapphire, “flip-needle” for
Seeburg DS conversion cartridge for Models M100B through 201, per pair
74-012 Stylus, Astatic N4-2S, 2 mil sapphire needle, (for reproductionvinyl 78 rpm records only), replaces old style straight needle
74-021 Stylus, Astatic N29-7S, .7 mil sapphire Z shaped needle for Astatic
# 51 cartridge, (.7 mil diamond tip for all 45 rpm stereo and mono. records)
74-022 Stylus, Astatic N29-2S, 2 mil sapphire Z shaped needle for Astatic
# 51 cartridge, (2 mil sapphire tip for reproduction-vinyl 78 rpm records only)
74-023 Stylus, Astatic N29-3D, 3 mil diamond Z shaped needle for Astatic
# 51 cartridge, (3 mil diamond tip for original 78 rpm records only)
74-020 Stylus, # 500-D1, 1 mil diamond needle for AMi Model F only
74-018 Stylus, # 501-D7, .7 mil diamond tip needle for all 45 rpm records,
replaces Astatic N350-1D, for AMi G & H only
(Needles, Replacement Styli, are continued on the next page)
- 71 -
$20.00
30.00
14.00
50.00
80.00
25.00
15.00
9.00
12.50
14.50
14.50
9.00
10.00
NEEDLES (Continued)
Please note: All Needles, (Replacement Styli), listed in this catalog,
are the Very best quality available. We do not sell inferior products.
A-1 PART #
74-002 Stylus, # 503-D7, .7 mil diamond needle, replaces Astatic N351-1D for AMi i, J,
K, Lyric, Continental I & II and United UPA & UPB, (for all 45 rpm records)
74-019 Stylus, Astatic SH122-7D, .7 mil diamond needle for AMi L, M, N, & O and
Rock-Ola 424, 425, 426, 429 & 433, (for all 45 rpm records)
74-014 Stylus, Astatic SH104-7D, .7 mil diamond needle, replacement for
Shure N44C needle, for AMi/Rowe MM1 thru MM6 & up to R-94,
Rock-Ola 436, 437, 440, 442, 444 & 446 thru 490-2
74-032 Stylus, special production, .7 mil diamond needle for
Wurlitzer One More Time 45 RPM, (for all 45 rpm records)
74-003 Stylus, # 159-D7, .7 mil diamond needle, replaces Astatic N43-7D
for Rock-Ola 1484, 1488, 1493, 1495, 1496, 1497, 404 408, 414, 418,
430, 431, 432, 434, 435, 441 and 445, (for all 45 rpm records)
$10.00
15.00
15.00
20.00
10.00
74-004 Styli, # 804-DS77, .7 mil diamond & .7 mil sapphire, “flip-needle”
for Wurlitzer 2300 thru 2600, (for all 45 rpm records),
See Note below, before ordering this replacement needle
10.00
74-005 Styli, # 808-DS77, .7 mil diamond & .7 mil sapphire, “flip-needle”
for Wurlitzer 2700 thru 3200, (for all 45 rpm records),
See Note below, before ordering this replacement needle
10.00
74-006 Styli, # 813-DS77, .7 mil diamond & .7 mil sapphire, “flip-needle”
for Wurlitzer 3300 only, (for all 45 rpm records),
See Note below, before ordering this replacement needle
10.00
74-013 Styli, Astatic N14-D, .7 mil diamond & .7 mil diamond, “flip-needle”
for Wurlitzer 3400 & 3500, (for all 45 rpm records),
See Note below, before ordering this replacement needle
9.00
74-007 Styli, Astatic N51-7D, .7 mil diamond & .7 mil diamond, “flip-needle” for
Wurlitzer 3600, 3700, 3800, 7500 & 1050, (for all 45 rpm records),
See Note below, before ordering this replacement needle
9.00
Note: For Wurlitzer models 2300 and newer: we recommend that the cartridge
be replaced using our A-1 part # 75-001, (Ceramic cartridge # P-132D),
(The price of the P-132D cartridge is $22.50 and includes a diamond needle).
74-011 Stylus, authentic Pickering, for NP/AC cartridge, .7 mil diamond needle
15.00
74-001 Styli, # 864-DS77, .7 mil diamond & .7 mil sapphire, “flip-needle”
for P-132D ceramic cartridge, (for all 45 rpm records)
10.00
74-030 Styli, # 864-DS73, .7 mil diamond & 3 mil sapphire, “flip-needle”
for P-132D ceramic cartridge, (one side plays 45s, one side plays 78s)
Fluorescent Lamps, Ballasts, Sockets & Starters are listed on the next page
- 72 -
8.00
FLUORESCENT LAMPS, BALLASTS, SOCKETS & STARTERS
Fluorescent lamp diameter guide:
T 5 = 5/8”,
T 8 = 1”,
T12 = 1 ½”
Suggestion: When replacing a fluorescent lamp, always install a new Starter.
If the Ballast is not in excellent condition, or if it is the original ballast,
we strongly suggest replacing it also.
A-1 PART #
70-025
70-001
70-002
70-024
70-023
70-016
70-004
70-005
70-017
70-018
70-022
70-021
70-026
70-020
70-006
70-007
70-008
70-009
70-019
70-010
70-011
70-012
70-013
70-014
Fluorescent lamp, 4 Watt 6”
Fluorescent lamp, 6 Watt 9"
Fluorescent lamp, 8 Watt 12"
Fluorescent lamp, 13 Watt 21"
Fluorescent lamp, 14 Watt 15"
Fluorescent lamp, 14 Watt 15"
Fluorescent lamp, 15 Watt 18"
Fluorescent lamp, 15 Watt 18"
Fluorescent lamp, 15 Watt 18"
Fluorescent lamp, 15 Watt 18"
Fluorescent lamp, 18 Watt 24"
Fluorescent lamp, 18 Watt 26"
Fluorescent lamp, 18 Watt 28"
Fluorescent lamp, 18 Watt 30"
Fluorescent lamp, 20 Watt 24"
Fluorescent lamp, 20 Watt 24"
Fluorescent lamp, 25 Watt 28"
Fluorescent lamp, 25 Watt 28"
Fluorescent lamp, 25 Watt 30"
Fluorescent lamp, 25 Watt 33"
Fluorescent lamp, 25 Watt 33"
Fluorescent lamp, 30 Watt 36"
Fluorescent lamp, 30 Watt 36"
Fluorescent lamp, 30 Watt 36"
T 5 cool white
T 5 cool white
T 5 cool white
T 5 cool white
T 8 cool white
T12 cool white
T 8 cool white
T 8 Daylight
T12 cool white
T12 Daylight
T 8 cool white
T 8 cool white
T 8 cool white
T 8 cool white
T12 cool white
T12 Daylight
T12 cool white
T12 Daylight
T12 cool white
T12 cool white
T12 Daylight
T 8 cool white
T 8 Daylight
T 8 BLB = Black light
$6.00
7.00
7.00
8.00
7.00
9.00
7.00
7.00
7.00
7.00
7.00
7.00
9.00
9.00
7.00
7.00
10.00
10.00
10.00
10.00
10.00
10.00
10.00
22.00
70-050 Colored sleeve for T12 fluorescent lamp, (cut to your specified length),
Specify: sleeve color: red, blue, green, yellow or pink, per foot
1.75
70-055 Colored sleeve for T8 fluorescent lamp,
Specify: sleeve color: red, blue, green, yellow or pink, per foot
1.75
71-005
71-003
71-001
71-006
71-035
Ballast 4 to 8 watt T5, for 1 lamp, new square style, clamped core, each
Ballast 13 watt T8, for 1 lamp, new square style, clamped core, each
Ballast 14 to 20 watt, for 1 lamp, new square style, clamped core, white, each
Ballast, 25 watt, for 1 lamp, new style, (clamped core), made in the U.S.A.
Ballast, 25 watt, for 1 lamp, original style case & Black color, (Now thermally
protected), made in the U.S.A., includes 2 rubber grommets for mounting
71-008 Ballast 30 to 40 watt, for 1 lamp, (Thermally protected), made in the U.S.A.
10.00
10.00
12.00
12.00
20.00
30.00
71-028 Starter with condenser, FS-U 4 thru 25 watts, (Replaces: FS-5, 4 to 8 watts,
FS-2, 15 to 20 watts and FS-25, 25 watts), each
71-010 Starter with condenser, FS-4, 30 to 40 watt, made in the U.S.A., each
1.50
1.50
71-015 Starter socket, exact match for most jukeboxes, (brown only)
4.00
71-013 Fluorescent lamp socket, T8 & T12, exact match for most jukeboxes, (black)
71-014 Fluorescent lamp socket, T8 & T12, exact match for most jukeboxes, (white)
4.00
4.00
- 73 -
FOILS, (EMBOSSED FOILS) FOR CABINET INTERIORS
A-1 PART #
65-008 Foil, embossed, gold, ¼” diamonds, for cabinet interior, 18" X 72" roll,
cloth backed, use spray adhesive for installation, per roll
65-009 Foil, embossed, gold, ¼” squares, for cabinet interior, 18" X 72" roll,
cloth backed, use spray adhesive for installation, per roll
65-011 Foil, embossed, silver, ¼” diamonds, for cabinet interior, 18” X 72” roll,
cloth backed, use spray adhesive for installation, per roll
65-012 Foil, embossed, silver, ¼” squares, for cabinet interior, 18” X 72” roll,
cloth backed, use spray adhesive for installation, per roll
65-003 Foil, embossed, gold, ½” pillowed squares, for interior of Seeburg C,
Wurlitzer 1080 & 1100, 32” X 16” sheet, (2 sheets required), per sheet
65-005 Foil, embossed, gold, ¾” squares, pattern area 30” X 14 ½”, per sheet
65-006 Foil, embossed, silver, ¾” squares, pattern area 30” X 14 ½” per sheet
$40.00
40.00
40.00
40.00
40.00
25.00
25.00
FUSES
A-1 PART #
97-005
97-002
97-003
97-004
37-009
Fuse, AGC, (fast acting), Specify: number of amps located on each fuse, ea.
Fuse, MDL, (slo-blo), Specify: number of amps located on each fuse, each
Fuse, GMQ, (red cap), Specify: number of amps located on each fuse, each
Fuse holder for GMQ fuses, Specify: ½, 8/10, 1 6/10 or 3 2/10 amps, each
Fuse, 3 amp or 3 2/10 amp Fustat, large screw in type, for Seeburg: M100A
thru VL200 Selection Receivers, (these are for the operation of wallboxes)
$2.50
3.50
4.50
8.00
8.00
GRILL CLOTH
A-1 PART #
65-002 Grill cloth: All colors except black & Burlap have metallic threads, 30" X 40",
Available colors, Specify: gold, red, silver, black, black with gold threads,
black with silver threads, green, royal blue, or white with gold threads, ea.
65-018 Grill cloth: Burlap, 30” X 40”, Available colors, Specify: red, black, gray
or medium blue, can be used on many 50s & 60s models, each
65-015 Speaker-board screen, (used in back of front metal grill screen), plastic fiber,
charcoal-black, for Seeburg Models 100J thru DS160. Can also be used
on other makes & models that have a front metal grill screen, 36” X 30”
$16.00
16.00
14.00
LINE CORDS, (POWER CORDS),
PLUGS & OUTLETS FOR LINE CORDS
A-1 PART #
71-016 Line cord 16/3 round, black, 11½ feet, with 90° angle, flat molded plug
71-025 Plug, 2 prong, non-polarized, black rubber cover, (Cooper quality), each
71-026 Outlet, vinyl cube tap for A. C. socket in all Receivers & Selector Units,
(Seeburg’s M100A through DS160), converts the socket to 3 A. C. outlets
71-030 Seeburg M100A through DS160, Outlet assembly, the line cord attaches
to this and the Receiver or Tormat Selection Unit plugs into this, (Note: This
Outlet is now a Grounded Duplex Receptacle for 3 wire line cords), brown
$12.00
2.50
3.00
8.00
LUBRICANTS
A-1 PART #
98-005 Luberplate, Aero lube, (white grease), for all Models, 3/8 oz. tube
98-006 Lubricating oil, highest quality, genuine turbine oil, perfect for lubricating
mechanisms and motors, 4 oz. plastic bottle with 9” telescoping extension
98-007 “PB Blaster”, best penetrating fluid & release agent for loosening any
“frozen” metal parts, especially Seeburg mechanisms, 12 oz. aerosol can
- 74 -
$3.00
3.00
7.00
PLUGS & SOCKETS FOR SPEAKERS, ETC.
A-1 PART #
37-025
37-026
37-014
37-031
37-032
37-035
37-041
37-042
37-051
37-061
37-062
37-071
37-072
37-081
37-091
37-092
37-093
37-101
37-102
37-111
37-121
37-122
37-125
37-131
37-132
Plug, SMALL, 2 round prongs, for Mech. cancel switch, without a cover
Plug, SMALL, 2 round prongs, for Mech. cancel switch, with a cover
Plug, two flat prongs, used in TSR1, 2 & 3, (J7 plug for reject switch)
Plug, SMALL, round, 3 prongs, Amphenol, for muting switch, without a cover
Plug, SMALL, round, 3 prongs, Amphenol, with Aluminum cover
Plug, SMALL, round, 4 prongs, Amphenol or Cinch, for credit units,
some are molded, some have covers, some do not have a cover
Plug, Large, 4 prongs, Amphenol, without a metal cover
Plug, Large, 4 prongs, Amphenol, with a metal cover
Plug, SMALL, round, 5 prongs, Amphenol or Cinch, for credit units
Plug, Large, 5 prongs, Amphenol, without a metal cover
Plug, Large, 5 prongs, Amphenol, with a metal cover
Plug, SMALL, round, 6 prongs, Amphenol or Cinch, for credit units
Plug, SMALL, round, 6 prongs, Amphenol or Cinch, with Aluminum cover
Plug, Large, 6 prongs, Amphenol: used in Seeburg M100A, B/BL & C,
Speaker Plug, (With or Without a Metal cover)
Plug, Large, 7 prongs, Amphenol, (Dummy plug for early 50s Seeburg
Amps. & Speaker plug in Wurlitzer 501, 502 & 503 Amps.), without a cover
Same as A-1 Part # 37-091, Plug, Large, 7 prongs, but with a metal cover
Plug, Large, 7 prongs, Amphenol, (Original, Molded, Dummy plug), wires
cannot be attached because this plug is molded & cannot be opened
Plug, Large, 8 prongs, Octal, (Speaker plug in Wurlitzer: 1100 thru 1650 and
is used for converting Wurlitzer 1015, 1080 & 1100 to Free Play, no cover
Same as A-1 Part # 37-101, Plug, Large, 8 prongs, but with a metal cover
Plug, 9 pin miniature, (Looks like the bottom of a 12AX7 tube), for Seeburg
HFMA1 thru newer Seeburg Amps. & some Rock-Ola’s, without a cover
Plug, Large, 11 prongs, Octal, for credit units, etc. Without a metal cover
Same as A-1 Part # 37-121, Plug, Large, 11 prongs, but with a metal cover
Socket, for Large, 11 prong, Octal plug, each
Plug, 27 prongs, Jones plug for Seeburg Wired selection receivers
Socket, for 27 prong Jones plug
$3.00
5.00
7.00
5.00
8.00
5.00
12.00
15.00
5.00
12.00
15.00
5.00
8.00
15.00
22.00
25.00
25.00
12.00
15.00
7.50
12.00
15.00
10.00
25.00
25.00
POLISH FOR METALS AND PLASTICS
Novus plastic polish: for cleaning and restoring plastics. Recommended for Use on:
Plexiglas, Lexan, Lucite, Uvex and Acrylite. Please Note: The ideal polishing cloth
Is nonabrasive, absorbent lint free and disposable, (reusable cloths retain abrasive
particles that will scratch plastic surfaces. Always use a new polishing cloth).
A-1 PART #
50-001 Novus #1, gently cleans, shines & protects all plastic surfaces without scratching.
Resists fogging, repels dust & eliminates static, 8 oz. non-aerosol pump bottle
50-002 Novus #2, removes fine scratches, haziness & abrasions from most plastics
restores faded and discolored plastics, 8 oz. squeeze bottle
50-003 Novus #3, removes scratches and abrasions from most acrylic surfaces.
Use Novus #3 when surface is too damaged to be restored using Novus #2, the use
of Novus #3 requires the use of Novus #2 for final finishing. 8 oz. squeeze bottle
50-004 Maas metal polishing cream is made with a base of jeweler’s rouge. It Cleans,
polishes & preserves chrome, aluminum, stainless steel, etc., 2 ounce tube
50-005 Maas metal polishing cream is made with a base of jeweler’s rouge. It Cleans,
polishes & preserves chrome, aluminum, stainless steel, etc., 4 ounce tube
- 75 -
$6.00
7.00
8.00
6.00
10.00
RECORDS, (7” 45 R.P.M. RECORDS)
As of November 2010, our inventory consists of approximately 11,000
45 R.P.M. records. All of the 45s on our Regular Price list are “new”.
New to us means: “Never played and in Mint condition”.
Our Newest Category of 45s is “Bargain Priced” 45s. Some of these 45s
are used, however, all are guaranteed against defects.
A Blank Title Strip is included with every 45 R.P.M. record that we sell and
Laser Printed Title Strips are $.25 each.
All of our 45s are guaranteed against defects.
Because our stock of 45 R.P.M. records changes often, we do not offer a
printed list of 45s. For a complete list of 45s, please visit our website:
www.jukeboxusa.com
TITLE STRIPS & RECORD ACCESSORIES
Blank Program Title Strips, for program title boards, for all 45 R.P.M.
Jukeboxes: All sheets are 8 ½” X 11” heavy stock, “perforated” sheets,
(Perfect for all computer printers and typewriters). Sheet configuration:
20 title strips per sheet. Packaged: 5 sheets, (100 title strips per package).
A-1 PART #
87-004
87-005
87-006
87-007
87-008
87-009
Title strips, Red border, perforated, 5 sheets of 20 per sheet = 100 strips
Title strips, Purple border, perforated, 5 sheets of 20 per sheet = 100 strips
Title strips, Blue border, perforated, 5 sheets of 20 per sheet = 100 strips
Title strips, Green border, perforated, 5 sheets of 20 per sheet = 100 strips
Title strips, Orange border, perforated, 5 sheets of 20 per sheet = 100 strips
Title strips, Blank, (No borders), perforated, (These are for our customers
who own the Title Strip Printing program and wish to print their own borders
when they print their title strips), 5 sheets of 20 per sheet = 100 strips
87-010 Title Strip Filing & Printing program for PCs, (CD by Low Profile Software),
(Compatible with: Windows 95, 98, 2000, ME, XP and Vista), not discountable
87-002 Record sleeves, white, for 7” 45 rpm records, each
87-003 Record sleeves, white, for 7” 45 rpm records, package of 100 pieces
$5.00
5.00
5.00
5.00
5.00
5.00
48.95
.15
12.00
RUBBER GASKET
Sponge rubber, with permanent adhesive backing, for inside dome glass,
lid glass & other areas that require this original type, (heavy duty), cushion.
A-1 PART #
64-001 Sponge rubber gasket, with permanent adhesive backing, original type,
black, 1/4" wide x 1/8” thick, per foot
64-002 Sponge rubber gasket, with permanent adhesive backing, original type,
black, 3/8” wide x 3/16” thick, per foot
64-003 Sponge rubber gasket, with permanent adhesive backing, original type,
black, 1/2” wide x 3/16” thick, per foot
64-004 Sponge rubber gasket, with permanent adhesive backing, original type,
black, 3/4” wide x 3/16” thick, per foot
(Tell us the Make & Model number of your jukebox and
we will supply the correct length and size of gasket that you need).
- 76 -
$.65
.90
1.15
1.40
TOOLS
A-1 PART #
98-001 Spring tension gauge for measuring tone arm weight, (for most jukeboxes),
(This is a Lifetime-quality item and this item is not discountable)
98-002 Points file, superior quality, (tungsten steel, lifetime-quality)
98-003 Contact, (points), adjuster, L shaped, chrome plated, lifetime-quality
98-008 Scriber, one end straight, one end L shaped, each end is threaded and
removable for scribing a tight area, lifetime-quality, made in USA
98-004 Low voltage tester, 5 to 50 volts AC/DC, (50 to 60 Hz), has visual
indicator and two insulated alligator clips
98-010 Circuit tester, 80 to 250 volts AC/DC, has visual indicator and probe, test leads
98-012 Hemostat, 5” straight end, for holding components while soldering, stainless
98-014 Hemostat, 5” curved end, for holding components while soldering, stainless
98-015 Flush Cutting Shear, Plato brand, has cushioned handles, made in The USA
$48.00
4.00
7.00
9.00
7.00
6.00
4.50
4.50
9.50
TUBES, (ELECTRON TUBES AND TUBE SOCKETS)
Please note: All Electron Tubes listed in this catalog are New and fully
Guaranteed to work to your complete satisfaction. We do not sell used tubes.
A-1 PART #
90-001
90-055
90-002
90-056
90-003
90-004
90-005
90-006
90-007
90-008
90-010
90-011
90-012
90-013
90-015
90-016
90-017
90-018
90-019
90-020
90-021
90-022
90-051
90-023
90-024
90-025
90-026
90-027
90-028
90-052
90-030
90-058
90-031
OA2 Electron tube
2A3 Electron tube, high quality, (Made in Russia)
2D21 Electron tube
5U4G Electron tube, high envelope, original pear shape, (Made in Russia)
5U4GB Electron tube, high quality, (Made in Russia)
5Y3GT Electron tube
5Z3 Electron tube
6AN8A Electron tube
6AU6 Electron tube
6AW8A Electron tube
6BA6 Electron tube
6BJ6 Electron tube
6BK7 Electron tube
6BQ5 / EL84 Electron tube, very high quality, (Made in Slovak Republic)
6C6 Electron tube and # 77 have the same internal components
6CA7 Electron tube
6CG7 Electron tube
6CY7 Electron tube
6EU7 Electron tube, high quality, (Made in Russia)
6F6 Electron tube
6H6 Electron tube
6J5GT Electron tube, (Glass)
6J5 Electron tube, (Metal)
6J7 Electron tube, (Metal)
6L6GC Electron tube, excellent quality, (Russian “Svetlana”)
6N7 Electron tube
6SA7 Electron tube, (Metal)
6SC7 Electron tube, (Metal)
6SJ7 Electron tube, (Metal)
6SK7 Electron tube, (Metal)
6SL7GT Electron tube, (Glass), high quality, (Made in The U.S.A. or Russia)
6SN7GTB, Electron tube, (Glass), New old stock, (Made in USA)
6SN7GTB, Electron tube, (Glass), high quality, (Made in Russia)
- 77 -
$10.00
45.00
8.00
40.00
20.00
14.00
24.00
14.00
8.00
8.00
8.00
10.00
9.00
16.00
9.00
28.00
15.00
14.00
25.00
12.00
10.00
14.00
12.00
14.00
20.00
10.00
8.00
17.00
12.00
12.00
19.00
24.00
16.00
TUBES, ELECTRON TUBES & TUBE SOCKETS (Continued)
A-1 PART #
90-065
90-034
90-032
90-033
90-035
90-036
90-037
90-038
90-039
90-040
90-042
90-043
90-044
90-045
90-057
90-046
90-047
90-053
90-048
90-054
90-037
90-049
90-050
90-061
6V6GT, Electron tube, (Glass), New old stock, (Made is USA)
6V6GT Electron tube, (Glass), high quality, (Made in Russia)
6X4 Electron tube
6X5GT Electron tube
12AT7 Electron tube, high quality, (Made in Russia)
12AU7A Electron tube
12AX7 Electron tube, same as # 7025, high quality, (Made in Russia)
12BH7A Electron tube
30 Electron tube
41 Electron tube
76 Electron tube
77 Electron tube and 6C6 have the same internal components
79 Electron tube
80 Electron tube
2050 Electron tube, high envelope, original pear shape, highest quality
2050A Electron tube, all name brands, excellent quality
5879 Electron tube
6CZ5 Electron tube, = Replacement for 6973, (Best for Seeburg Amps.)
6EM5 Electron tube, = Replacement for 6973, (Best with minor modifications)
6973 Electron tube, not a substitute, high quality, (Made in Russia)
7025 Electron tube, same as 12AX7, high quality, (Made in Russia)
7199 Electron tube, high quality, (Made in Russia)
7868 Electron tube, (This item is not discountable at this price)
Tube socket / connector socket, 7 pin ceramic pc mount for pc boards in
Seeburg Models KS200, KD200 and L100, each
90-062 Tube socket, 8 pin octal ceramic pc mount for holding 5U4, 6L6 & 2050
tubes in pc boards in Seeburg Models KS200, KD200 and L100, each
90-063 Tube socket / connector socket, 9 pin ceramic pc mount for pc boards in
Seeburg Models KS200, KD200 and L100, each
90-064 Metal shield & inner spring, (covers 9 pin electron tubes such as 5879)
$24.00
16.00
12.00
14.00
15.00
14.00
16.00
25.00
30.00
20.00
24.00
9.00
10.00
28.00
30.00
24.00
18.00
18.00
18.00
32.00
16.00
45.00
70.00
Our “Customer Satisfaction Guarantee” applies to every original jukebox part,
reproduction jukebox part and/or accessory that is purchased from us.
If you have any questions, please send us an Email or give us a call, anytime.
Copyright © 2003, 2008 and 2010
2010/2011 Catalog
A-1 Jukebox & Nostalgia, Inc.
Exclusive Distributor of “Ken Arnold brand”
and other “exact reproduction” Parts for Jukeboxes
To Place an Order:
Phone 410-945-8900
Fax Orders: 410-945-1946 (For Fax transmissions only)
Email: [email protected]
Please visit our Website: www.jukeboxusa.com for a complete list of parts & 45s
(As of November 1, 2010: Online ordering is unavailable until further notice)
- 78 -
5.00
5.00
5.00
4.00