1. No category

How to Measure an Inside Mount Window
e from
id
u
g
n
io
t
a
ll
a
t
a simple ins
ore
The Shutter St
www.shutters.co.uk
How to Measure an Inside Mount Window
ABS Range
Before you start you will need:
• A good quality steel tape measure
• A spirit level
• Paper and pen
Measure the
window and
record the
size , go awa
y and have a
cup of tea,
go back, mea
sure again, “
measure
twice, cut on
ce :-) ”
Tip!
Our shutters are supplied with a custom built frame.
INSIDE MOUNT refers to the direction that the fixing holes are predrilled in the
shutter frame. Therefore if you have a recess wall or a reveal which is deep enough
to accommodate our shutter frames you can choose to fit your shutters as an INSIDE
MOUNT INSTALLATION
• USE A STEEL TAPE MEASURE
• Measure inside recess from left side to right side. Take the width at 3 different locations
across the window and give us the SMALLEST width.
• Measure inside recess from top to bottom. Take the height at 3 different locations
along the window and give us the SMALLEST drop.
• If there are tiles which will reduce the overall width inside the recess you should
measure within this area ( the smallest width in the recess). We can supply matching
trim with your order should you need to cover any visible gaps you may have above
the tiles.
• We recommend we make a small deduction (-2 mm) to the smallest width and the
smallest drop you supply. This will allow some ease when fitting the frame. We DO
NOT make this deduction as standard, you will be asked to agree to it.
• If the side walls of the recess are splayed at an angle we can supply matching trim to allow
you to obtain a seamless installation from wall to wall. (Widest trim we carry is 50mm)
• If you have an inward opening window or door you will need to consider the space you
have around the window to allow for our frame to sit without restricting the window
movement.
• Please see our photos and illustration guides on how to measure correctly.
• If you do have an unusual window or need further assistance please email us direct
with a CLEAR IMAGE OF THE WHOLE WINDOW, we will show you in detail how to
measure correctly!
If you would like further advice on your actual window, please email a clear digital image to
[email protected] Ensure all curtains are moved away from the window and
that handles and the full window is in the photo.
www.shutters.co.uk
How to Measure an Inside Mount Window
ABS Range
What we recommend
Full height shutters fitting tight up
to the window = 4 sides frame
Different types
of ins
mounted shutt ide
ers
Shutters on French doors = 3 sides
frame LRT
Tier on tier shutters fitting tight up
to the window = 4 sides frame
Shutters fitting at front of recess
to allow panels to bifold back 180
degrees & sit against interior walls
= 3 sides frame LRT
Cafe Style shutters = 3 sides frame LRB
If you would like further advice on your actual window, please email a clear digital image to
[email protected] Ensure all curtains are moved away from the window and
that handles and the full window is in the photo.
www.shutters.co.uk
How to Measure an Inside Mount Window
ABS Range
Inside Mount L frame BL63
L frame – suitable for all slat sizes. Situate frame inside recess to position you desire,
pulling forward of the window sufficient for slats to tilt and not hit the window.
Plan view of window & frame looking down from above with inside mount fixing
holes.
38 mm
63 mm
22 mm
shutter hinges here
If you would like further advice on your actual window, please email a clear digital image to
[email protected] Ensure all curtains are moved away from the window and
that handles and the full window is in the photo.
www.shutters.co.uk
How to Measure an Inside Mount Window
ABS Range
Inside Mount BULLNOSE Z frame DPZ 38
Z frame with INSIDE MOUNT FIXING HOLES... Suitable for a slat size of 47mm, 64mm or
89mm, 114mm (you must have additional clearance space in the recess to allow 64mm,
89mm, 114mm slats to tilt)
Frame Ref: BULLNOSE Z Frame (Decorative CROWN Z available. Measure and install
principle exactly per below)
Plan view of window & frame looking down from above
Z frame with inside mount fixing holes
We offer our “Z” frame for Inside Mount shutters fitting inside the front of the recess.
This frame is a semi recessed frame. The frame will mount inside the recess at the front
of the opening The molded “Z” edge gives a beautiful finished look to the installation
and also allows the panels to fold back 180 degrees to sit back on the wall either side of
window.
Please see illustration for size and position of Z frame in the recess
38 mm
49 mm
38 mm
shutter hinges here
If you would like further advice on your actual window, please email a clear digital image to
[email protected] Ensure all curtains are moved away from the window and
that handles and the full window is in the photo.
www.shutters.co.uk
How to Measure an Inside Mount Window
ABS Range
How To Measure An Inside Mount
1. Measure width x drop as per RED lines
2. For a midrail position, measure from bottom up to GREEN line. We will centre our
dividing midrail at this point.
3. For cafe (half height) or tier on tier (double hung) shutters, measure from bottom up
to the BLUE line for the finish height of the lower panel.
NOTE: Inserting a midrail in a panel can offer flexibility on how you tilt the slats. A
midrail can cover a handle or rail on your window or door. A midrail will offer greater
strength and stability to taller shutter panels.
If you would like further advice on your actual window, please email a clear digital image to
[email protected] Ensure all curtains are moved away from the window and
that handles and the full window is in the photo.
www.shutters.co.uk
How to Measure an Inside Mount Window
ABS Range
Checking for Obstructions
Before measuring, look for any obstructions on the window. You need to make
sure that you avoid the possibility of the slats tilting open and hitting any
obstacles such as handles or a telephone junction box.
If ordering shutters for an inside mount with an L frame, there is one frame
available. You should locate the frame at a position inside the recess where the
slats will not hit the window or obstructions.
The drawings below show how far beyond the rear of the L frame, the slats will
protrude.
47mm slat with
46mm deep frame
46mm
40mm
shutter frame
47mm
If you would like further advice on your actual window, please email a clear digital image to
[email protected] Ensure all curtains are moved away from the window and
that handles and the full window is in the photo.
www.shutters.co.uk
How to Measure an Inside Mount Window
ABS Range
Below is an example of how full height shutters with a mid rail would look when installed.
Inside mounted shutters
If you would like further advice on your actual window, please email a clear digital image to
[email protected] Ensure all curtains are moved away from the window and
that handles and the full window is in the photo.
www.shutters.co.uk
How to Measure an Inside Mount Window
ABS Range
Template cut outs
Inside Mount L frame DPL60
38 mm
38 mm
63 mm
63 mm
22 mm
22 mm
38 mm
38 mm
63 mm
63 mm
22 mm
22 mm
Please note before printing this template page, the PAGE SCALING box needs to be set
to ‘NONE’. This will ensure the templates print to scale. This box will appear as an option
when you print the page
www.shutters.co.uk
How to Measure an Inside Mount Window
ABS Range
Template cut outs
Inside Mount BULLNOSE Z frame
38 mm
49 mm
9 mm
38 mm
38 mm
49 mm
9 mm
38 mm
Please note before printing this template page, the PAGE SCALING box needs to be set
to ‘NONE’. This will ensure the templates print to scale. This box will appear as an option
when you print the page