1/29/14, 5:24 PM
Juniper Networks - How to configure and verify the DHCP relay for EX-series switches - Knowledge Base
1/29/14, 5:24 PM
How to configure and verify the DHCP relay for EX-series switches
[KB11020] Show KB Properties
SUMMARY:
ASK THE KB
Question or KB ID:
Ask
This article provides information on how to configure and verify the DHCP relay for the EX-series switches.
PROBLEM OR GOAL:
How to configure and verify the DHCP relay for the EX-series switches.
Knowledge Center Home
CAUSE:
Browse Popular Content
SOLUTION:
Topology:
Browse Recently Updated
Browse All
[Client PC] --- ge-0/0/0 [EX Switch] ge0/0/1 --- [DHCP Server]
Client PC is in VLAN 10.
The DHCP server is in VLAN 20 with the 20.20.20.2 IP address.
Knowledge Center News
J-Net Search
PR Search
The EX switch is configured as DHCP relay and performs inter VLAN routing between VLANs 10 and 20.
Configuration:
set
set
set
set
vlans vlan10 vlan-id 10
interfaces ge-0/0/0 unit 0 family ethernet-switching vlan members vlan10
vlans vlan10 l3-interface vlan.10
interfaces vlan unit 10 family inet address 10.10.10.1/24
set
set
set
set
set
set
vlans vlan20 vlan-id 20
interfaces ge-0/0/1 unit 0 family ethernet-switching vlan members vlan20
interfaces vlan unit 20 family inet address 20.20.20.1/24
vlans vlan20 l3-interface vlan.20
forwarding-options helpers bootp server 20.20.20.2
forwarding-options helpers bootp interface vlan.10
Create a Support Case
Knowledge Center Feedback
Report a Security Vulnerability
Browse Knowledge Base
Categories
Note: VLAN.10 Routed VLAN Interface (RVI) is configured for bootp relay, so that bootp packets in VLAN 10 will be routed
to the '20.20.20.2' server in VLAN 20. Configure the specific RVIs, to which the bootp packets should be forwarded. A
separate server can be configured under the 'bootp interface vlan.X' stanza for only that specific VLAN. A global server IP
can also be specified (as above), which is applicable for all RVI interfaces.
Verifying the DHCP Relay configuration on an EX switch:
juniper@EX> show configuration forwarding-options
helpers {
bootp {
server 20.20.20.2;
interface {
vlan.20;
}
}
}
Verifying relay agent activity on EX:
juniper@EX> show helper statistics
bootps:
Received packets: 4
Forwarded packets: 4
Dropped packets: 0
Due to no interface in fud database: 0
Due to no matching routing instance: 0
Due to an error during packet read: 0
Due to an error during packet send: 0
Due to invalid server address: 0
Due to no valid local address: 0
Due to no route to server/client: 0
Note: The 4 packets shown above are packets that are relayed from the client to the server (Discover, Request) and from
the server to the client (Offer, Ack) by the EX switch.
To see DHCP packets entering or exiting an interface, the monitor traffic interface <int-name> command can be used.
http://kb.juniper.net/InfoCenter/index?page=content&id=KB11020
Page 1 of 2
Juniper Networks - How to configure and verify the DHCP relay for EX-series switches - Knowledge Base
1/29/14, 5:24 PM
To debug relay agent activity on EX :
[edit]
set forwarding-options helpers traceoptions file helper
set forwarding-options helpers traceoptions flag bootp
set forwarding-options helpers traceoptions level level
After forwarding activity, the /var/log/helper file can be viewed. By default, helper activity is logged in /var/log/fud, which
is viewed by using show log fud.
Troubleshooting Tip: When the debugs and show commands that verify bootp packets are being relayed or forwarded, if
the IP address is still not obtained, check the path between the client's gateway and the DHCP server. Ensure that routes
are in place and no firewall rules are blocking these bootp packets.
Caution:
Debugs using traceoptions should be used with care; especially on a busy router or switch. It is advisable to turn
them on only for specific feature(s) at any given time, and for specific flag and level options of interest and turn them
off, when no longer needed. Else, this can cause high CPU activity and affect other processes.
Monitoring live output by 'monitor start <trace-file-name>' can generate excess network traffic, if there is
too much data; so avoid it in a busy production environment and use the trace files for viewing later.
RELATED LINKS:
Site Map / RSS Feeds / Careers / Accessibility / Feedback / Privacy & Policy / Legal Notices
http://kb.juniper.net/InfoCenter/index?page=content&id=KB11020
Copyright© 1999-2012 Juniper Networks, Inc. All rights reserved.
Page 2 of 2
© Copyright 2024