EQUIPMENT How to Describe Gates Hydraulic Hose Assemblies When you order hydraulic assemblies, be sure the following information is included as shown in the illustrations below: 1. Quantity of assemblies required. 2. Hose catalog description (dash size and type). 3. First coupling dash size and end style. 4. Second coupling dash size and end style. 5. Offset angle or orientation of couplings must be specified if both couplings contain bent tube ends. 6. Assembly overall length. HOSE/CPLG. SELECTION G8K COUPLINGS GLOBALSPIRAL COUPLINGS PCM/PCS FERRULES MEGACRIMP COUPLINGS STAINLESS STEEL 12EFG4K POWER CRIMP COUPLINGS LOC, GL AND GLP COUPLINGS POLARSEAL COUPLINGS POLARSEAL II COUPLINGS C14 COUPLINGS 12EFG4K PCTS THERMOPLASTIC COUPLINGS FIELD ATTACHABLE G1 AND G2 COUPLINGS FIELD ATTACHABLE C5 AND C5E COUPLINGS SURELOK AIR BRAKE COUPLINGS Caution: Rated working pressure of the application should always determine selection of hose. Used up to the recommended rated working pressure, the hose will provide normal service life before replacement is required. When new, the hose described in this catalog will meet or exceed the minimum burst pressure listed in the hose specification tables. However—as with any hose in the industry—after the hose has been impulsed for a length of time, minimum burst pressure will decrease from the figure shown in the specification tables. Temperature ranges specified for specific hoses refer to recommended temperature limits of fluids being conveyed or ambient temperatures. Exceeding these limits will cause degradation of material compounds and reduce hose service life. ADAPTERS QUICK DISCONNECT COUPLERS LIVE SWIVEL BALL VALVES ACCESSORIES EQUIPMENT AND PARTS ® Powering Progress. gates.com/hydraulics GATES HYDRAULICS EQUIPMENT HOSE/CPLG. SELECTION How to Describe Gates Hydraulic Hose Assemblies – con’t. G8K COUPLINGS GLOBALSPIRAL COUPLINGS PCM/PCS FERRULES MEGACRIMP COUPLINGS Coupling A Information Male Female Angle ____° Drop: S L XL or Drop Length_____ (mm) Thread STAINLESS STEEL JIC (37° Flare) POWER CRIMP COUPLINGS LOC, GL AND GLP COUPLINGS _________ POLARSEAL II COUPLINGS C14 COUPLINGS PCTS THERMOPLASTIC COUPLINGS Gates __________ I.D. ___________ or SAE 100R _____________________ ACCESSORIES EQUIPMENT AND PARTS S M L XL or Drop Length_____ (mm) Dash Size: 2 3 4 5 6 8 10 12 16 20 24 32 40 48 56 Thread JIC (37° Flare) _________ NPTF _________ Temperature ___________° O-Ring Boss _________ Flat-Face O-Ring _________ Working Pressure (psi): Flat-Face O-Ring _________ Code 61 _________ Code 62 _________ BSPP _________ DIN (Light/Heavy) Other Overall Length ____________ 100 250-499 1001-2999 4000-5999 101-250 500-1000 3000-3999 6000 Application Return Line Pressure Line _________ Intake Line High Pressure Line _________ Special Fluid _________________ (ORFS) Code 61 _________ Code 62 _________ BSPP _________ DIN (Light/Heavy) _________ Other _________ Hose Guards In. mm Coupling Orientation:___________ ° 90° 64 Full Length Partial Length From End of Coupling _______ _______ _______ _______ _______ _______ _______ _______ _______ _______ LifeGuard™ Sleeve Wire Spring 270° Flat Armor Spring 0° BALL VALVES Angle ____° Drop: _________ ADAPTERS LIVE SWIVEL Female O-Ring Boss 180° QUICK DISCONNECT COUPLERS Male _________ FIELD ATTACHABLE C5 AND C5E COUPLINGS SURELOK AIR BRAKE COUPLINGS Coupling B Information NPTF (ORFS) POLARSEAL COUPLINGS FIELD ATTACHABLE G1 AND G2 COUPLINGS M Hose Type Measure from centerline of flanged head to centerline of flanged head for length of assembly. Offset angle is measured with far coupling vertically downward. Orientation angle is measured clockwise. gates.com/hydraulics Nylon Sleeve Plastic Coil Sleeve Gates Corporation16 ®
© Copyright 2024