1. home and garden

HOW TO
MEASURE AN
IMPERIAL PRODUCT
PN 3366-8
© 2006 Imperial Supplies LLC
see back of guide
for index - page 31
A
CAP SCREWS, FLANGE BOLTS AND ALL TYPES OF CARRIAGE SCREWS
TOOLS NEEDED: bolt gauge or digital caliper
•
•
•
For length, measure from under the head to the end with the bolt gauge or digital caliper.
For diameter, use the holes in the bolt gauge or digital caliper.
USS and SAE threads are determined by threads per inch on backside of gauge.
ALL TYPES OF NUTS
TOOLS NEEDED: bolt gauge or digital caliper
•
•
For size, use the towers at the ends of the bolt gauge or digital caliper.
Half way down for USS, and all the way down for SAE.
A cap screw can also be used to determine the size of the nut.
WASHERS
TOOLS NEEDED: bolt gauge or digital caliper
•
•
Measure the inside and outside diameters with the bolt gauge or digital caliper.
A cap screw can also be used to determine the size.
SPEED NUTS
TOOLS NEEDED: bolt gauge or digital caliper and drill gauge
•
•
•
2
Use sheet metal and machine screws to determine thread size and diameters.
Compare on drill gauge for stud diameters.
Use the bolt gauge or digital caliper for the “center of hole edge” measurement.
Imperial Supplies LLC – How to Measure Product
EYE BOLTS
A
TOOLS NEEDED: bolt gauge or digital caliper and Weatherhead gauge or digital caliper
®
•
•
•
•
Measure the diameter “A” with the bolt gauge or digital caliper.
Measure the length “B” from the bottom of the eye to the end with the
bolt gauge or digital caliper.
Measure the diameter of the eye “C” with the Weatherhead® gauge.
Measure the overall length “D” with the bolt gauge or digital caliper.
D
A
C
B
SHOULDER EYE BOLTS
TOOLS NEEDED: bolt gauge or digital caliper and Weatherhead gauge
®
•
•
•
•
Measure
Measure
Measure
Measure
the
the
the
the
inner diameter of the eye with the Weatherhead® gauge.
outer diameter of the eye with the bolt gauge or digital caliper.
length from under the shoulder to the end.
thread pitch with bolt gauge or digital caliper.
SPRING CENTER BOLTS
TOOLS NEEDED: bolt gauge or digital caliper
•
•
Measure the length and diameter with the bolt gauge or digital caliper.
Measure the thread pitch with bolt gauge or digital caliper.
THREADED ROD
TOOLS NEED: bolt gauge or digital caliper
•
•
Measure the length and diameter with the bolt gauge or digital caliper.
Measure the thread pitch with bolt gauge or digital caliper.
PLOW BOLTS
TOOLS NEEDED: bolt gauge or digital caliper
•
•
•
Measure the diameter with the bolt gauge or digital caliper.
Measure the length with the tapered side of the
bolt gauge or digital caliper.
Measure the thread pitch with bolt gauge or digital caliper.
Imperial Supplies LLC – How to Measure Product
3
A
MACHINE SCREWS
TOOLS NEED: bolt gauge or digital caliper
• Measure the length, diameter, and thread count with the bolt gauge or digital caliper.
SHEET METAL SCREWS
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the length and diameter with
the bolt gauge or digital caliper.
TEK SCREWS
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the length and diameter with the bolt gauge or digital caliper.
SELF-DRILLING SCREWS
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the length and diameter
with the bolt gauge or digital caliper.
LAG SCREWS
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the length and diameter with the bolt gauge or digital caliper.
4
Imperial Supplies LLC – How to Measure Product
FLOOR SCREWS
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the length, thread pitch and diameter
with the bolt gauge or digital caliper.
A
SOCKET HEAD PRODUCTS
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the length, thread pitch and diameter
with the bolt gauge or digital caliper.
SHOULDER SCREWS
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the shoulder length and diameter
with the bolt gauge or digital caliper.
• Measure the thread size, thread pitch (diameter)
with the bolt gauge or digital caliper.
METRIC NUTS
TOOLS NEEDED: metric pitch gauge
• Measure the thread pitch with the pitch gauge.
• The diameter of the nut is determined by using a metric cap screw.
METRIC WASHERS
TOOLS NEEDED: bolt gauge or digital caliper
• Compare the inner diameter of the washer on the
metric holes on the bolt gauge or digital caliper.
• A metric cap screw can also be used to
determine the inner diameter.
Imperial Supplies LLC – How to Measure Product
5
A
METRIC CAP SCREWS
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the length with the metric portion of the bolt gauge or digital caliper.
• Measure the length and diameter with the
metric portion of the bolt gauge or digital caliper.
• Measure the thread pitch with the
bolt gauge or digital caliper.
METRIC MACHINE SCREWS
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the length, thread pitch and diameter with the
metric portion of the bolt gauge or digital caliper.
METRIC SOCKET PRODUCTS
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the length, thread pitch and diameter with the
metric portion of the bolt gauge or digital caliper.
STAINLESS STEEL NUTS
TOOLS NEEDED: bolt gauge or digital caliper and magnet
• 18/8–304 and –316 stainless steel will not stick to a magnet.
• Measure the diameter on the towers at the ends
of the bolt gauge or digital caliper, half way
down for USS and all the way down for SAE.
• A cap screw can also be used to
determine the diameter of the nut.
STAINLESS STEEL WASHERS
TOOLS NEEDED: bolt gauge or digital caliper and magnet
• 18/8–304 and –316 stainless steel will not stick to a magnet.
• Compare the inner diameter of the washers on the bolt gauge or digital caliper.
• A cap screw can also be used to determine the diameter of the washer.
6
Imperial Supplies LLC – How to Measure Product
STAINLESS STEEL CAP SCREWS
TOOLS NEEDED: bolt gauge or digital caliper and magnet
• Stainless steel will not stick to the magnet.
• Measure the length, thread pitch and diameter
with the bolt gauge or digital caliper.
A
STAINLESS STEEL MACHINE SCREWS
TOOLS NEEDED: bolt gauge or digital caliper and magnet
• Stainless steel will not stick to a magnet.
• Measure the length and diameter with the
bolt gauge or digital caliper.
STAINLESS STEEL THREADED ROD
TOOLS NEEDED: bolt gauge or digital caliper and magnet
• Stainless steel will not stick to the magnet.
• Measure the length and diameter with
the bolt gauge or digital caliper.
STAINLESS STEEL SOCKET PRODUCTS
TOOLS NEEDED: bolt gauge or digital caliper and magnet
• Stainless steel will not stick to the magnet.
• Measure the length and diameter with the bolt gauge or digital caliper.
Imperial Supplies LLC – How to Measure Product
7
A
STAINLESS STEEL CARRIAGE SCREWS
TOOLS NEEDED: bolt gauge or digital caliper and magnet
• Stainless steel will not stick to the magnet.
• Measure the length and diameter with the bolt gauge or digital caliper.
STAINLESS STEEL METRIC CAP SCREWS
TOOLS NEEDED: bolt gauge or digital caliper, metric pitch gauge and magnet
• Stainless steel will not stick to the magnet.
• Measure the length with the metric portion of the bolt gauge or digital caliper.
• Measure the diameter and thread pitch with the metric portion of the bolt gauge or digital caliper.
STAINLESS STEEL SHEET METAL SCREWS
TOOLS NEEDED: bolt gauge or digital caliper and magnet
• Stainless steel will not stick to the magnet.
• Measure the length and diameter with the bolt gauge or digital caliper.
8
Imperial Supplies LLC – How to Measure Product
ANCHORS
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the length and diameter
with the bolt gauge or digital caliper.
B
WEJ-IT
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the shank length and diameter with the bolt gauge or digital caliper.
STAINLESS STEEL COTTER PINS
TOOLS NEEDED: bolt gauge or digital caliper, drill gauge and magnet
• Stainless steel will not stick to the magnet.
• Measure the length from the bottom of the curve to the end of the shortest leg.
• Measure the diameter with the drill gauge.
shortest leg
Diameter
Length
STAINLESS STEEL ROLL PINS
TOOLS NEEDED: bolt gauge or digital caliper, and drill gauge
• Measure the length with the bolt gauge or digital caliper.
• Measure the diameter with the drill gauge.
Imperial Supplies LLC – How to Measure Product
9
HAIRPIN CLIPS
B
TOOLS NEEDED: bolt gauge or digital caliper and drill gauge
• Measure the overall length of “B” with the bolt gauge or digital caliper.
• Measure the diameter of “C” by comparing it on the drill gauge.
• Measure the wire diameter of “A” with the drill gauge.
A
C
B
HAIRPIN COTTERS
TOOLS NEEDED: bolt gauge or digital caliper and drill gauge
• Measure the overall length of “B” with the bolt gauge or digital caliper.
• Measure the diameter of “C” by comparing it on the drill gauge.
• Measure the wire diameter of “A” with the drill gauge.
A
C
B
HITCH PINS
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the length from under the shoulder to the end with the bolt gauge or digital caliper.
• Measure the diameter with the bolt gauge or digital caliper.
Length
SNAPPER PINS
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the useable length (from under the head to the groove)
with the bolt gauge or digital caliper.
• Measure the diameter with the bolt gauge or digital caliper.
• Measure the clearance - “A” with the bolt gauge or digital caliper.
A
10
A
Imperial Supplies LLC – How to Measure Product
A
LYNCH PINS
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the length “E” with the bolt gauge or digital caliper.
• Measure the diameter “A” with the bolt gauge or digital caliper.
• Measure the inside diameter of the ring “F” with the bolt gauge or digital caliper.
F
B
E
A
DOWEL PINS
TOOLS NEEDED: bolt gauge or digital caliper and drill gauge.
• Measure the length with the bolt gauge or digital caliper.
• Measure the diameter with the drill gauge.
CLEVIS PINS
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the length from under the head to the end with the bolt gauge or digital caliper.
• Measure the diameter with the bolt gauge or digital caliper.
CLEVIS YOKES
TOOLS NEEDED: bolt gauge or digital caliper
• Measure length “A” from the center of the hole to the end with the bolt gauge or digital caliper.
• Measure the diameter of the throat width “B” with the bolt gauge or digital caliper.
• Measure the thread size with the towers at the ends of the pitch gauge or digital caliper.
• Measure the yoke width “C” with the bolt gauge or digital caliper.
B
C
A
11
SNAP RINGS
B
TOOLS NEEDED: snap ring size chart
• Place the snap ring on the size
chart to determine the size.
E-CLIPS
TOOLS NEEDED: e-clip size chart
• Place the e-clip on the size chart to determine the size.
HALF MOON KEYS (WOODRUFF KEYS)
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the length and thickness
with the bolt gauge or digital caliper.
Thickness
th
Leng
HOSE CLAMPS
TOOLS NEEDED: None
• Size is stamped on the clamp.
HIGH TORQUE, CONSTANT TORQUE AND T-BOLT CLAMPS
TOOLS NEEDED: None
• Use the cross reference sheet for these clamps.
12
Imperial Supplies LLC – How to Measure Product
TWO-EAR CLAMPS
TOOLS NEEDED: digital caliper
• Select two ear clamp which size is nearest to, but
always larger than the outer material to be clamped.
• Measure the outer diameter of the clamp with
the digital caliper.
B
WIRE ROPE CLIPS
TOOLS NEEDED: Weatherhead® gauge.
• Measure the U portion of the collar
with the Weatherhead® gauge.
TUBE CLAMPS
TOOLS NEEDED: bolt gauge or digital caliper
• Close the clamp, then compare the inside
diameter on the bolt gauge or digital caliper.
FRAME CLIPS
TOOLS NEEDED: bolt gauge or digital caliper
• Use the bolt gauge or digital caliper to measure
lengths “A, B, and C” as well as the width.
C
B
A
KWIK STIK CLIPS
TOOLS NEEDED: Weatherhead® gauge
• Measure the diameter of the clip with the Weatherhead® gauge.
13
JIFFY CLIPS
B
TOOLS NEEDED: Weatherhead® gauge.
• Measure the half diameter of the clip
with the Weatherhead® gauge.
CRIMP SLEEVES
TOOLS NEEDED: drill gauge
• Compare the hole diameter to the drill gauge.
OPEN EYE SNAP BOLTS
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the overall length and the eye
opening with the bolt gauge or digital caliper.
RIGID EYE SNAP BOLTS
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the overall length, eye size, and the
snap opening with the bolt gauge or digital caliper.
REPLACEMENT S HOOKS
TOOLS NEEDED: bolt gauge or digital caliper and drill gauge.
• Measure the overall length with the
bolt gauge or digital caliper.
• Measure the wire diameter with the drill gauge.
14
Imperial Supplies LLC – How to Measure Product
SAFETY SNAP HOOK
TOOLS NEEDED: bolt gauge or digital caliper and Weatherhead gauge.
• Measure the overall length and the snap
opening with the bolt gauge or digital caliper.
• Measure the wire diameter with the Weatherhead® gauge.
®
B
NUTSERTS
TOOLS NEEDED: bolt gauge or digital caliper
• Use the towers at the end of the bolt gauge or digital caliper
for thread diameter: halfway (USS), all the way (SAE).
• Machine screws and cap screws can also be
used to determine thread size.
FLANGE KNURLED NUTSERTS
TOOLS NEEDED: bolt gauge or digital caliper
• Use the towers at the end of the bolt gauge or digital caliper
for thread diameter: halfway (USS), all the way (SAE).
• Machine screws and cap screws can also
be used to determine thread size.
THREAD REPAIR KITS
TOOLS NEEDED: bolt gauge or digital caliper
•
•
•
Use the towers at the end of the bolt gauge or digital caliper
for thread diameter: halfway (USS), all the way (SAE).
Machine screws and cap screws can also be
used to determine thread size.
Measure the outer diameter of the thread repair piece with the
bolt gauge or digital caliper to determine thin wall from thick wall.
GREASE FITTINGS
TOOLS NEEDED: bolt gauge or digital caliper and Weatherhead gauge
• Measure the 1/8" and 1/4" pipe thread with the
pipe thread portion of the Weatherhead® gauge.
• Measure the 1/4–1/28 drive and metric
fittings with the bolt gauge or digital caliper.
• Measure the button head fittings with
the Weatherhead® gauge.
®
Imperial Supplies LLC – How to Measure Product
15
COMPRESSION SPRINGS
B
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the length and diameter with the
bolt gauge or digital caliper.
O.D.
wire size
free length
ROD ENDS
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the male thread with the
bolt gauge or digital caliper.
• Measure the female thread with the
towers of the bolt gauge or digital caliper:
halfway (USS), all the way (SAE)
• A cap screw can also be used to determine
the thread size.
BALL JOINTS
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the male thread with the bolt gauge or digital caliper.
• Measure the female thread with the towers of the
bolt gauge or digital caliper: halfway (USS), all the way (SAE).
GRADE 40 CHAIN
TOOLS NEEDED: Weatherhead® gauge
• Measure the chain size (diameter) with
the Weatherhead® gauge.
GRADE 80 CHAIN
TOOLS NEEDED: drill gauge and Weatherhead® gauge
• Measure the 9/32" chain size by comparing the
diameter of the chain on the drill gauge.
• Measure the 3/8" chain size with the Weatherhead® gauge.
16
Imperial Supplies LLC – How to Measure Product
GRADE 40 CLEVIS GRAB AND SLIP HOOKS
TOOLS NEEDED: bolt gauge or digital caliper
• Grab hook: measure the opening of the hook with
the bolt gauge to determine chain size.
• Slip hook: measure the opening of hook with the
bolt gauge or digital caliper, to determine the chain size.
Then take the “chain size” x 2 and the “nominal inside width”
and add them together for the hook size.
B
QUICK LINKS
TOOLS NEEDED: Weatherhead® gauge.
• Measure the diameter with the Weatherhead® gauge.
DOUBLE CLEVIS MID LINKS
TOOLS NEEDED: Weatherhead® gauge.
• Measure the clevis pin with the Weatherhead® gauge and
compare to the closet “nominal inside width” of chain.
REPAIR LAP LINKS
TOOLS NEEDED: bolt gauge or digital caliper and Weatherhead gauge
• Measure inside length of link with the bolt gauge or digital caliper.
• Measure the diameter of the link
with the Weatherhead® gauge.
®
KUPLERS FOR CHAIN
TOOLS NEEDED: Weatherhead gauge
• Measure the clevis pin with the Weatherhead® gauge and
compare that with the closet “nominal inside width”
measurement of the chain.
®
Imperial Supplies LLC – How to Measure Product
17
OBLONG MASTER LINKS
B
TOOLS NEEDED: bolt gauge or digital caliper and Weatherhead® gauge
• Measure “A” with the Weatherhead® gauge and find
the closet “nominal inside width” measurement of the chain.
• Measure “B” and “C” with the bolt gauge or digital caliper.
A
B
D
O-RING / METRIC O-RINGS
TOOLS NEEDED: None
• Place the o-ring on the size chart in
Section B of the Imperial catalog.
FIREWALL GROMMETS
TOOLS NEEDED: None
• Place the firewall grommet on the size chart in the catalog.
18
Imperial Supplies LLC – How to Measure Product
RIVETS
TOOLS NEEDED: bolt gauge or digital caliper, drill gauge, and rivet gauge
• Measure diameter with the drill and
bolt gauge or digital calipers.
• Measure the rivet lengths with the rivet gauge.
• Measure the lengths under head with the drill
and bolt gauge or digital calipers.
C
D
TRUCK-LITE®
TOOLS NEEDED: None
• Use the number on the item to cross in catalog, or label comparable item.
LAMPS / MINIATURE BULBS
TOOLS NEEDED: None.
• Use the manufacturers number on the light to label.
Imperial Supplies LLC – How to Measure Product
19
FUSES
TOOLS NEEDED: None
• Amp sizes are stamped on the fuses.
E
BATTERY TERMINALS
TOOLS NEEDED: bolt gauge or digital caliper and battery gauge
• Measure the gauge size with the battery gauge.
• Most terminals have the gauge stamped on them.
BATTERY LUGS
TOOLS NEEDED: bolt gauge or digital caliper and battery gauge
• Measure the ring size or stud size with
the bolt gauge or digital caliper.
• Measure the gauge size with the battery gauge.
ELECTRICAL TERMINALS
TOOLS NEEDED: bolt gauge or digital caliper, drill gauge and electrical gauge.
Smaller gauges: yellow = 10-12 gauge
blue = 14-16 gauge
red = 18-22 gauge
Larger gauges:
yellow = 4 gauge
blue = 6 gauge
red = 8 gauge
• Ring, spade and hook terminals, use electrical gauge to determine diameter.
• Heat shrink: size is stamped on it, or compare with bolt gauge or digital caliper.
• Nylon cable ties: measure overall length with the bolt gauge or digital caliper.
20
Imperial Supplies LLC – How to Measure Product
COMPRESSION, PERMALIGN AND POLYLINE FITTINGS
TOOLS NEEDED:
• Measure the tube size with the tube size portion of the Weatherhead® gauge.
• Measure the pipe size with the pipe size portion of the Weatherhead® gauge.
• Measure the female pipe size by using a male pipe thread fitting.
INVERTED FLARE FITTINGS
TOOLS NEEDED: Weatherhead gauge and bolt gauge or digital caliper
• Measure the tube size by using the correct size SAE cap screw.
Put in the bolt gauge or digital caliper and cross the size over
on the back of the Weatherhead® gauge.
• Measure the pipe size with the pipe size portion
of the Weatherhead® gauge.
®
F
45° FLARE FITTING
TOOLS NEEDED: bolt gauge or digital caliper, Weatherhead gauge and flare nose cone gauge
• For tube size: put flared end into bolt gauge or digital caliper
and cross over size on back of Weatherhead® gauge.
• Measure pipe size with the pipe size thread portion
of the Weatherhead® gauge.
• Measure the female pipe size with a male pipe thread fitting.
• The flare nose cone gauge can also be used to determine the tube size.
®
BRASS FITTINGS
TOOLS NEEDED: Weatherhead gauge
• Measure the male pipe size with the pipe thread portion of the Weatherhead® gauge.
• Measure the female pipe size with a male pipe thread fitting.
®
BULK HEAD FITTINGS
TOOLS NEEDED: bolt gauge or digital caliper and Weatherhead gauge
• Measure the overall length with the bolt gauge or digital caliper.
• Measure the male pipe size with the pipe thread portion of the Weatherhead® gauge.
• Measure the female pipe size with a male pipe thread fitting.
• Measure the 3/4, 7/8, 1" and 1-1/8 thread with
the bolt gauge or digital caliper.
®
Imperial Supplies LLC – How to Measure Product
21
37° JIC STEEL FITTINGS
TOOLS NEEDED: bolt gauge or digital caliper, Weatherhead® gauge and flare nose cone gauge.
• For the tube size: put the flared end into the bolt gauge or digital caliper and cross on the back
of the Weatherhead® gauge.
• Measure the male pipe size with the pipe thread
portion of the Weatherhead® gauge.
• Measure the female pipe size with a male pipe size fitting.
• The flare nose cone gauge can also be used to determine tube size.
F
37° O-RING / O-RING SWIVEL ADAPTERS
TOOLS NEEDED: bolt gauge or digital caliper, Weatherhead® gauge and flare nose cone gauge.
• For tube size: put in the bolt gauge or digital caliper and cross
over on the back of the Weatherhead® gauge.
• For port size: put in the bolt gauge or digital caliper and
cross over the back of the Weatherhead® gauge.
• Measure the female thread on the swivel
adapters with a male pipe thread fitting.
• The flare nose cone gauge can also be used to determine tube size.
SWIVEL ADAPTERS
TOOLS NEEDED: Weatherhead® gauge
• Measure the male pipe size with the pipe thread
portion of the Weatherhead® gauge.
• Measure the female pipe size with a male pipe thread fittings.
DRAIN COCKS, SHUT OFF COCKS AND VALVES
TOOLS NEEDED: Weatherhead® gauge
• Measure the male pipe size with the pipe thread portion of the Weatherhead® gauge.
• Measure the female pipe size with a male pipe thread fitting.
22
Imperial Supplies LLC – How to Measure Product
MINI - BARB FITTINGS
TOOLS NEEDED: Weatherhead gauge
• Measure the pipe size with the pipe thread portion of the Weatherhead® gauge.
• Measure the smallest part of the barb end with the
tube outer diameter portion of the Weatherhead® gauge.
®
BRAKE ADAPTERS
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the male thread with SAE nuts and
cross over size on the brake adapter chart.
• Measure the female side SAE cap screws and
cross over size on the brake adapter chart.
F
GALVANIZED AND BLACK IRON FITTINGS
TOOLS NEEDED: Weatherhead gauge
• Measure the male pipe size with the thread
portion of the Weatherhead® gauge.
• Measure the female pipe size with a
male pipe thread fitting.
®
HIGH PRESSURE STEEL PIPE FITTINGS
TOOLS NEEDED: Weatherhead® gauge
• Measure the male pipe size with the pipe thread portion of the Weatherhead® gauge.
• Measure the female pipe size with a male pipe thread fitting.
Imperial Supplies LLC – How to Measure Product
23
NYLON, PUSH-IN / AIR BRAKE FITTING
TOOLS NEEDED: Weatherhead® gauge
• Measure the tube size with the outer diameter portion of the Weatherhead® gauge.
• Measure the male pipe size with the pipe thread portion of the Weatherhead® gauge.
• Measure the female pipe size with a male pipe thread fitting.
• The tube size is also stamped on the nut next to D.O.T.
G
24
RUBBER AIR BRAKE FITTINGS
TOOLS NEEDED: Weatherhead® gauge
• Size is stamped on nut next to D.O.T.
• For sleeves: 3/8" fits on the 1/2" pipe thread circle of the
Weatherhead® gauge and 1/2" fits on 3/4".
• The insert can be used to determine the size of the fitting–use the
tube outer diameter portion of the Weatherhead® gauge.
• Measure the male pipe size with the pipe thread
portion of the Weatherhead® gauge.
Imperial Supplies LLC – How to Measure Product
BRASS HEATER HOSE FITTINGS
TOOLS NEEDED: Weatherhead gauge
• Measure the hose side with the tube outer diameter
portion of the Weatherhead® gauge.
• Measure the male pipe size with the pipe
thread portion of the Weatherhead® gauge.
®
BARB–TITE FITTINGS
TOOLS NEEDED: bolt gauge or digital caliper and Weatherhead® gauge.
• Measure the barb end with the hose inner diameter portion of the Weatherhead® gauge.
• Measure flared end by placing in the bolt gauge or digital caliper
and crossing over on the back of the Weatherhead® gauge.
• Measure inverted end using an SAE bolt and
crossing over on the back of the weather gauge.
• Measure the male pipe size with the pipe
thread portion of the Weatherhead® gauge.
H
REUSABLE HOSE ENDS
TOOLS NEEDED: bolt gauge or digital caliper and Weatherhead® gauge.
• Size is stamped on nut.
• Measure the female swivel with an SAE cap screw and
cross over on back of the Weatherhead® gauge.
• Measure the male pipe size with the thread portion
of the Weatherhead® gauge.
• Measure the inverted size with the tube outer diameter
portion of the Weatherhead® gauge on the shaft tube.
COLL-O-CRIMP HOSE ENDS
TOOLS NEEDED: bolt gauge or digital caliper, Weatherhead® gauge and flare nose cone gauge
• Measure the hose size with the tube outer diameter
portion of the Weatherhead® gauge on the end of the insert.
• Measure the female swivel with an SAE cap screw and
cross over on the back of the Weatherhead® gauge.
• Measure the flared end by putting in the bolt gauge or digital
caliper and crossing over on the back of the Weatherhead® gauge.
• The flared end can also be measured with the flare nose cone gauge.
• Measure the male pipe size with the pipe thread
portion of the Weatherhead® gauge.
Imperial Supplies LLC – How to Measure Product
25
CUTTING TOOLS
TOOLS NEEDED: bolt gauge or digital caliper and drill gauge
• Measure the lengths and diameters with the bolt gauge or digital caliper and drill gauge.
• Compare what the customer has on their shelf to what we have in our catalog and label
appropriate item.
WELDING PRODUCTS
TOOLS NEEDED: None
• Compare what the customer has on their shelf to what
we have in our catalog and label appropriate item.
I
26
Imperial Supplies LLC – How to Measure Product
OIL DRAIN PLUGS AND GASKETS
TOOLS NEEDED: bolt gauge or digital caliper
• Use the bolt gauge or digital caliper and the cheat
sheet provided from the catalog to determine size.
• Measure the inner diameter and outer diameter of
the gaskets with the bolt gauge or digital caliper.
EXPANSION PLUGS
TOOLS NEEDED: None
• Size is stamped on the plug.
PLUG BUTTONS
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the head diameter with the bolt gauge or digital caliper.
CARBURETOR THROTTLE ROD CLIPS
TOOLS NEEDED: drill gauge
• Compare the hold diameter on the drill gauge.
• Use the cross reference number chart to match the number on the clip.
ROD END CLIPS
TOOLS NEEDED: drill gauge
• Compare the most narrow part of the hole on the drill gauge.
N
TIRE PRODUCTS
TOOLS NEEDED: none
• Compare what the customer has on their shelf to what
we have in our catalog and label appropriate item.
Imperial Supplies LLC – How to Measure Product
27
KEYS
TOOLS NEEDED: None
• Use the manufacturers number that is stamped on the key.
WHEEL WEIGHTS
TOOLS NEEDED: None
• The size is stamped on the weights.
FLEXIBLE DRAW LATCH
TOOLS NEEDED: bolt gauge or digital caliper
• Measure diameter “A” and “B” with the bolt gauge or digital caliper.
B
N
MUFFLER CLAMPS
TOOLS NEEDED: None
• Size stamped on the bottom of collar.
28
Imperial Supplies LLC – How to Measure Product
when latched
A
EXHAUST CLAMPS
TOOLS NEEDED: None
• Size is stamped on clamp and on the box.
DRIVE FLANGE WEDGES
TOOLS NEEDED: Weatherhead gauge
• Measure the outside diameter with the Weatherhead® gauge.
®
STUDS
TOOLS NEEDED: bolt gauge or digital caliper
• Measure the length and diameter with the
bolt gauge or digital caliper.
• Measure the length of USS (A) thread with
the bolt gauge or digital caliper.
• Measure the length of SAE (B) thread with
the bolt gauge or digital caliper.
A
B
N
TRUCK WHEEL NUTS (BUD NUTS)
TOOLS NEEDED: None
• Inner nuts are stamped on the end with an L for left or an R for right.
• Outer nuts are stamped with the word LEFT or the word RIGHT.
Imperial Supplies LLC – How to Measure Product
29
SAFETY EQUIPMENT
TOOLS NEEDED: None
• Compare what the customer has on their shelf to what we
have in our catalog and label appropriate item.
CHEMICALS
TOOLS NEEDED: None
• Compare what the customer has on their shelf to what we
have in our catalog and label appropriate item.
SHOP SUPPLIES
TOOLS NEEDED: None
• Compare what the customer has on their shelf to what
we have in our catalog and label appropriate item.
SCANNER TRAINING
Be
•
•
•
•
•
•
•
•
30
sure to check scanner before training begins
Get to know your scanner inside and out. You need to be confident when training the customer.
Review the instructions before training begins.
Be sure to type “test” in the P.O. if the customer is not going to place an order.
Which, by the way, should rarely happen.
Make sure the customer signs the “NO CHANGE” lease agreement.
The customer training should be hands on.
Walk the customer through the instruction sheet step-by-step.
Order # 1-8 is for a shop with multiple locations. This feature allows the
customer to place up to eight separate orders and send them in at the same time.
These orders will be boxed and invoiced separately so the customer knows
what he or she ordered for each location.
A part number can be deleted by pressing the LEFT ARROW key until
you get to the number to be deleted. At that point, press the CLEAR button.
Press the RIGHT ARROW key to get to the end of the file and continue scanning.
Imperial Supplies LLC – How to Measure Product
INDEX
37° JIC Steel Fittings . . . . . .
37° O-ring Adapters . . . . . .
45° Flare Fitting . . . . . . . . .
Air Brake Fitting . . . . . . . . .
Anchors . . . . . . . . . . . . . . .
Ball Joints . . . . . . . . . . . . . .
Barb–Tite Fittings . . . . . . . . .
Battery Lugs . . . . . . . . . . . .
Battery Terminals . . . . . . . . .
Black Iron Fittings . . . . . . . .
Brake Adapters . . . . . . . . . .
Brass Fittings . . . . . . . . . . . .
Brass Heater Hose Fittings . .
Bud Nuts . . . . . . . . . . . . . .
Bulk Head Fittings . . . . . . . .
Cap Screws . . . . . . . . . . . .
Carburetor Throttle Rod Clips
Carriage Screws . . . . . . . . .
Chemicals. . . . . . . . . . . . . .
Clevis Grab Hooks . . . . . . .
Clevis Pins . . . . . . . . . . . . .
Clevis Yokes . . . . . . . . . . . .
Coll-O-Crimp Hose Ends . . . .
Compression Fittings . . . . . .
Compression Springs . . . . . .
Constant Torque Clamp . . . .
Crimp Sleeves . . . . . . . . . . .
Cutting Tools . . . . . . . . . . . .
Double Clevis Mid Links . . . .
Dowel Pins . . . . . . . . . . . . .
Drain Cocks . . . . . . . . . . . .
Drive Flange Wedges. . . . . .
E-clips . . . . . . . . . . . . . . . .
Electrical Terminals . . . . . . .
Exhaust Clamps. . . . . . . . . .
Expansion Plugs . . . . . . . . .
Eye Bolts. . . . . . . . . . . . . . .
Firewall Grommets. . . . . . . .
Flange Bolts . . . . . . . . . . . .
Flange Knurled Nutserts . . . .
Flexible Draw Latch . . . . . . .
Floor Screws . . . . . . . . . . . .
Frame Clips . . . . . . . . . . . .
Fuses . . . . . . . . . . . . . . . . .
Galvanized Fittings . . . . . . .
Gaskets . . . . . . . . . . . . . . .
Grade 40 Chain . . . . . . . . .
Grade 80 Chain . . . . . . . . .
Grease Fittings . . . . . . . . . .
Hairpin Clips . . . . . . . . . . .
Hairpin Cotters . . . . . . . . . .
Half Moon Keys . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
22
22
21
24
. 9
16
25
20
20
23
23
21
25
29
21
. 2
27
. 2
30
17
11
11
25
21
16
12
14
26
17
11
22
29
12
20
29
27
. 3
18
. 2
15
28
. 5
13
20
23
27
16
16
15
10
10
12
High Pressure Steel Pipe Fittings
High Torque Clamp . . . . . . . . .
Hitch Pins . . . . . . . . . . . . . . . .
Hose Clamps . . . . . . . . . . . . .
Inverted Flare Fittings . . . . . . . .
Jiffy Clips . . . . . . . . . . . . . . . .
Keys . . . . . . . . . . . . . . . . . . .
Kuplers for Chain . . . . . . . . . .
Kwik Stik Clips . . . . . . . . . . . .
Lag Screws . . . . . . . . . . . . . . .
Lamps / Miniature Bulbs. . . . . .
Lynch Pins . . . . . . . . . . . . . . . .
Machine Screws . . . . . . . . . . .
Metric Cap Screws . . . . . . . . .
Metric Machine Screws . . . . . .
Metric Nuts. . . . . . . . . . . . . . .
Metric Socket Products . . . . . . .
Metric Washers . . . . . . . . . . . .
Mini - Barb Fittings. . . . . . . . . .
Muffler Clamps . . . . . . . . . . . .
Nuts. . . . . . . . . . . . . . . . . . . .
Nylon Fittings . . . . . . . . . . . . .
O-ring / Metric O-rings . . . . . .
O-ring Swivel Adapters . . . . . .
Oblong Master links . . . . . . . .
Oil Drain Plugs . . . . . . . . . . . .
Open Eye Snap Bolts . . . . . . . .
Permalign Fittings . . . . . . . . . .
Plow Bolts . . . . . . . . . . . . . . . .
Plug Buttons . . . . . . . . . . . . . .
Polyline Fittings . . . . . . . . . . . .
Push-in Fittings. . . . . . . . . . . . .
Quick Links . . . . . . . . . . . . . . .
Repair Lap Links . . . . . . . . . . .
Replacement S Hooks. . . . . . . .
Reusable Hose Ends. . . . . . . . .
Rigid Eye Snap Bolts . . . . . . . .
Rivets . . . . . . . . . . . . . . . . . . .
Rod End Clips . . . . . . . . . . . . .
Rod Ends . . . . . . . . . . . . . . . .
Rubber Air Brake Fittings . . . . .
Safety Equipment. . . . . . . . . . .
Safety Snap Hook . . . . . . . . . .
Scanner Training . . . . . . . . . . .
Self-Drilling Screws . . . . . . . . .
Sheet Metal Screws . . . . . . . . .
Shop Supplies . . . . . . . . . . . . .
Shoulder Eye bolts . . . . . . . . . .
Shoulder Screws . . . . . . . . . . .
Shut Off Cocks . . . . . . . . . . . .
Shut Off Valves . . . . . . . . . . . .
Slip Hooks . . . . . . . . . . . . . . .
Imperial Supplies LLC – How to Measure Product
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
23
12
10
12
21
14
28
17
13
. 4
19
11
. 4
. 6
. 6
. 5
. 6
. 5
23
28
. 2
24
18
22
18
27
14
21
. 3
27
21
24
17
17
14
25
14
19
27
16
24
30
15
30
. 4
. 4
30
. 3
. 5
22
22
17
Snap Rings . . . . . . . . . . . . . . . . .
Snapper Pins. . . . . . . . . . . . . . . .
Socket Head Products . . . . . . . . .
Speed Nuts. . . . . . . . . . . . . . . . .
Spring Center Bolts . . . . . . . . . . .
Stainless Steel Cap Screws . . . . . .
Stainless Steel Carriage Screws. . .
Stainless Steel Cotter Pins . . . . . . .
Stainless Steel Machine Screws . . .
Stainless Steel Metric Cap Screws .
Stainless Steel Nuts . . . . . . . . . . .
Stainless Steel Roll Pins. . . . . . . . .
Stainless Steel Sheet Metal Screws.
Stainless Steel Socket Products . . .
Stainless Steel Threaded Rod. . . . .
Stainless Steel Washers . . . . . . . .
Studs . . . . . . . . . . . . . . . . . . . . .
Swivel Adapters . . . . . . . . . . . . .
T-Bolt Clamps . . . . . . . . . . . . . . .
Tek Screws . . . . . . . . . . . . . . . . .
Thread Repair Kits . . . . . . . . . . . .
Threaded Rod . . . . . . . . . . . . . . .
Tire Products . . . . . . . . . . . . . . . .
Truck Wheel Nuts . . . . . . . . . . . .
Truck-Lite. . . . . . . . . . . . . . . . . . .
Tube Clamps . . . . . . . . . . . . . . . .
Two-Ear Clamps . . . . . . . . . . . . .
Washers. . . . . . . . . . . . . . . . . . .
WEJ-IT . . . . . . . . . . . . . . . . . . . .
Welding Products . . . . . . . . . . . .
Wheel Weights . . . . . . . . . . . . . .
Wire Rope Clips . . . . . . . . . . . . .
Woodruff Keys . . . . . . . . . . . . . .
12
10
. 5
. 2
. 3
. 7
. 8
. 9
. 7
. 8
. 6
. 9
. 8
. 7
. 7
. 6
29
22
12
. 4
15
. 3
27
29
19
13
13
. 2
. 9
26
28
13
12
31
Imperial Supplies LLC
789 Armed Forces Drive
P.O. Box 11008
Green Bay, WI 54307-1008
Same Day Shipping! • Personal Customer Service! • Risk Free Guarantee!
Imperial stocks over 20,000 parts …
■ Fasteners
■ Rivets and Rivet Guns
■ Electrical Products
■ Air Brake Products
■ Cutting Tools
■ Safety Products
■ Chemicals and Paint
■ Vehicle Parts & Accessories
Hardware
Vehicle Lighting
■ Tubing and Tube Fittings
■ Hose and Hose Ends
■ Abrasives
■ Welding Supplies
■ Shop Supplies
■ Assortments & Steel Equipment
■
■
Quality products, outstanding service, and exceptional value!
Imperial has made a concerted effort to provide accurate information in its catalog and on its website, however Imperial assumes no responsibility for the accuracy of the information. All information
published by Imperial in its catalogs, marketing literature, and on its website is provided “as is” without warranty, expressed or implied. Imperial and its vendors disclaim all warranties, expressed or
implied including, without limitation, warranties of merchantability and fitness for a particular purpose.
PN 3366-8
© 2006 Imperial Supplies LLC