Lifetime When compared to the years old and widely

Kink loss of BendBright-XS when bent
Splice Loss Distribution of BendBright-XS
45º around a very small radius pin
to SMF and to itself at 1550 nm
dB
10
@1550 nm
ESMF
1
When compared to the years old and widely
minimum storage radius are out-dated.
accepted minimum storage radius of 30 mm,
Just like standard SMF, the choice of pure
35%
a reduction to 7.5 or 15 mm might raise
materials and clean processing conditions
30%
concern about lifetime issues. However,
result in fiber quality that meet all conditions
this topic has been studied thoroughly by
with respect to lifetime. For modern cables
Draka and others in the industry, and the
this involves that a low level continuous
conclusion is that high quality fibers, such
strain of 1/3 of the proof-test level for 20
Glass that handles
as BendBright-XS, can fully cope with these
years is allowed over its full length. In storage
like “copper wire”
circumstances. Because fiber quality has
cassettes, a much higher strain applied
increased dramatically over the past decade,
over a much shorter length leads to the
the assumptions that led to the 30 mm
same low probability of breakage.
25%
BendBright-XS to
BendBright-XS
R
x100
20%
0,1
BendBright-XS to
SMF
15%
BendBright-XS
10%
0,01
5%
0,001
dB
0%
1,5
2,0
R (mm)
Lifetime
0,00
0,02
0,04
0,06
0,08
0,10
> 0,10
Other characteristics
Apart from the macrobending loss, very
Backwards compatibility with fibers used
•
low loss at short radii in the millimeter
in existing networks requires parameters
•
Exceeds toughest bending standards; ITU-T G.657.B
range, referred to as “kink loss”, is a
such as loss, dispersion, PMD and cut-off
•
Fully backwards compatible with SMF; G.652.D compliant
remarable feature of BendBright-XS.
wavelength to be in the same range. As
•
Close to 1 billion meters sold since 2006
Because of the industry leading coating
compared to legacy SMF, the mode field
•
Deployed in over 30 countries worldwide
technology utilized by Draka, BendBright-XS
diameter of BendBright-XS shows a small
also gives a 100x improvement in
average reduction of about 0.2µm, much
•
Tens of million splices and connectors
microbending over standard ESMF. The
different than other bend-insensitive fiber
•
Used everywhere in the network!
100x bending improvement over SMF
combination of the 100x improvement in
that have very small mode field diameters,
microbending and 100x improvement in
and thus are not compatible with existing
macrobending results in a fiber with the
SMF fibers. Fusion splicing is an important
Further information
performance shown in the plot below. “Kink
consideration for new fiber types. As the plot
Interested by these new exciting possibilities?
loss” deformations induce an added loss that shows, BendBright-XS has excellent splice
Contact Draka and ask for the full datasheet and extended Application Note with more
is similar to the loss of an average splice, as
performance, achieved with standard splicing
details on various aspects of applying this industry leading bend-insensitive fiber.
opposed to much higher losses with standard
equipment. Likewise, cleaving or polishing
Demand the Best... Demand BendBright-XS!
SMF. This makes a BendBright-XS network
of the end faces is unchanged compared
very friendly to fiber engineering errors like
with standard SMF.
of patchcords etc... It’s this very characteristic
that makes BendBright-XS fiber handling
like working with good old “copper wires”.
BendBright-XS
Why BendBright-XS ?
Kink losses
overclamping the fiber, tie wrapping bundles
I N N O V A T I O N
Draka Communications
Netherlands:
France:
USA:
Email: fi[email protected]
Tel: +31 (0)40 29 58 700
Tel: +33 (0)3 21 79 49 00
Toll free: 800-879-9862
Outside US: +1.828.459.9787
Fax: +31 (0)40 29 58 710
Fax: +33 (0)3 21 79 49 33
Fax: +1.828.459.8267
Website: www.drakafiber.com | www.draka.com
www.draka.com
Macrobend performance of BendBright-XS
•
• ••
•••
•••• ••••
•• •• ••
•••
•
•••
•••
•• •
••• •
••••
•••
•
of what we call Value Innovation, and it’s
what drives us.
I N N O V A T I O N
advantage of the excellent bending proper-
access networks, Draka also realizes that
the industry in a new direction, with the
ties of the fiber, including the aerospace,
the proliferation of fiber types has
introduction of bend-insensitive optical
marine oil & gas, broadcast, military, home
a negative cost impact for the network
fibers for use in optical access networks.
entertainment and trans-portation industries,
operator. Maintaining an up-to-date network
Draka’s flagship bend-insensitive fiber,
just to name a few. BendBright-XS is enabling
administration and stock level of cables
0,0001
BendBright-XS , has helped redefine the way
applications in which fiber was previously
with different fiber types is a burden to
0,00001
optical access networks are designed and
not an option.
many operators. Therefore, BendBright-XS
0,1
0,01
0,001
0
5
10
15
specifications
20
25
30
bend radius (mm)
has been designed such that it is fully
The industry leader
fibers (SMF) used in the trunk and metro
core, which is very beneficial in keeping
Since it’s introduction in 2006, over
networks. Because BendBright-XS is fully
the signal inside the fiber when the fiber
compliant with the low-waterpeak single
is bent. Using a trench to achieve this
close to 1 million km of BendBright-XS,
It’s benefits
enough to circumnavigate the globe 25
Excellent Macrobend Performance
mode standard, ITU-T G.652D, some
level of performance is only possible using
times over, has been deployed in over 30
Considering the harsh environment in local
operators have decided not to mix fibers,
Draka’s versatile Plasma Chemical Vapor
countries worldwide. People recognize
loop network deployment, Draka quickly
but rather chosen to deploy BendBright-XS
Deposition (PCVD) process.
the benefits of a fiber that meets the most
realized that macrobending loss is a para-
throughout their FTTH network, from
Central Office to the customer’s home.
meter of vital importance. Supporting smaller
and denser footprints, fiber management
exceeds the bend loss requirements of ITU-T
traditional SMF. BendBright-XS is fully
systems can save expensive space in the
G.657.B, the most stringent bending
With over 20 million subscribers worldwide,
compliant with ITU-T G.657 A and B, as well
telecom offices and cabinets. Engineer-
standard in the industry. This is an order
Fiber-to-the-Home (FTTH) access networks
as the low water peak single mode standard,
friendly fiber performance for accidental
are re-shaping the way people conduct their
ITU-T G.652.D. This results in a fiber that
low radius kinks and bends can prevent
lives. Whether it’s video chatting, on-line
is 100x improved in both macrobending and
excessive rework and allow for the employ-
Macrobending loss
BendBright, and two orders of magnitude
gaming, running peer-to-peer applications,
microbending over traditional low water
ment of lower skilled labor forces. The very
The key feature in the fiber design that
over conventional ESMF. BendBright-XS is
high-definition movies on-demand, or
peak single-mode fiber. The majority of
same cost reducing characteristics will also
allows for such significant improvement in
fully compliant with both the A and B classes
watching videos on YouTube, there has been
the success of BendBright-XS is driven by
support further reduction of maintenance
macrobending performance is the insertion
of the ITU-T G.657 bend insensitive fiber
•••••••••••••••••
••
or complete network designs - it’s all part
manufacturer in the world, Draka has led
1550 nm
1
stringent bending standards in the industry,
••••••
we’ll make it for you. New applications,
breakthrough cables, custom connectors
loss is most relevant in the last mile of
ht
ig
solution that will do more than meet your
of other applications have emerged taking
yet is fully backwards compatible with
your challenge, we have a product or
needs. And if for some reason we don’t,
beginning. As the largest fiber optic cable
dB/turn
MF
ES
are designed to last. No matter how complex
•••
communication solutions and services that
•••
value to their business with advanced
Although the need for low macrobending
compatible with the existing single-mode
••
• •• ••••••••
strong, long-lasting relationships, we add
•••
•••••
with technological know-how and building
the early adopter of this fiber, a wide array
deployed today and in the future.
• ••
•••
more? A lot. We help our customers to
stay ahead. By combining market insight
•••
••• •• • •• •• • •• • • •• •••••
• ••
do more, make more, save more and achieve
• •• ••
been a pioneer in this market from the
S
t-X
igh
world. What we can do to help our customers
••
•••
Backwards compatibility
Br
nd
Be
Value Innovation is a way of looking at the
compared to industry standards and other fibers
While the telecommunications industry is
Br
nd
Be
Draka Communications – a member of Draka Holding N.V. located
in Amsterdam – offers a versatile and reliable range of copper
and optical fiber cables for the transmission in the data and
telecommunication industry. Our long-lasting expertise in cable
and fiber business has been the basis for us holding a major market
position today. Draka Communications is located in more than 30
countries in Europe, Asia, North America and South America.
and passive network manufacturer, has
It’s characteristics
As the figure below depicts, BendBright-XS
of magnitude improvement over Draka’s
1st generation bend-insensitive fiber,
tremendous growth in user-driven demand
the large scale deployment of FTTH access
cost in case of frequent reconfiguration
of a field confining “trench” in the fiber
standard, established in 2006. The fiber is
for high bandwidth optical access networks.
networks by the major telecommunication
of the network due to customer churn or
cladding. This trench reduces the optical
also fully compliant with ITU-T G.652.D low
Draka Communications, a leading fiber, cable,
carriers in both North America and Europe.
further built-out of the access network.
power in the region just outside the guiding
water peak single-mode fiber specification.