Submittal Review Cover Sheet

Submittal Review Cover Sheet
Project#: 11DB-C5-08-61-02-PS14
Project: 11-13-07 Fire Station # 2
Date:
Submittal#:
Architect#
12/30/13
20
Revision#
0
Owner#
1312 Bowman Street
To:
Clermont, FL 34711
Phone (352) 394-1032
Fax: (352) 394-1794
Submitter: Kevin Boutros
City of Zephyrhills
5335 8th Street
Zephyrhills, FL 33540
Phone: (813) 780-0022
Fax:
(813) 780-0025
Our Job#:
50041
Sub or Supplier
Fire Safety, Inc.
P.O Box 17371,
Clearwater, FL 33762-0371
Contact: Shane LeBlanc
Spec#
210500
Paragraph Spec Description
FIRE SUPPRESSION
Item Name
FIRE SUPPRESSION
Item Type
Comment
Reason:
Reviewed By
Pillar Construction Group, LLC
Review is for general design only. Subcontractor and or Supplier are responsible for dimensions, quantities, and full
compliance with the requirements of the contract documents. Review or approval by the architect or engineer does not
relieve the Subcontractor and or Supplier of the responsibilities required by the terms and conditions of the agreement
with Pillar Construction Group, LLC.
Date:
By:
AREA FOR OTHER REVIEW STAMPS AND COMMENTS:
PILLAR CONSTRUCTION GROUP, LLC
Date 12/30/13
By: Kevin Boutros
No Exception Taken
Make Corrections Noted
Revise & Resubmit
Rejected
This shop drawing review is for general
performance with contract documents only and
does not relieve the subcontractor or fabricator
of his responsibility for compliance with
requirements of the drawings and specifications.
Submittal#
20
Spec Section# 210500
Drawing#
Form: SubOne-G1
12/30/13
Zephyrhills Fire Station #2
3810 6th Avenue.
Zephyrhills, Florida
Contractor:
Pillar Construction Group, LLC.
Architect:
Canerday, Belfsky + Arroyo. Architects
Fire Protection Consultant:
Engineering Matrix, Inc.
Installing Contractor:
Fire Safety, Inc.
P.O. Box 17371
Clearwater, Florida 33762-0371
Date:
December 26th, 2013
Material Submittals
Aboveground Fire Suppression Sprinkler Systems
INDEX
- Pipe and Fittings. (Aboveground Only) ------------------------------------------------- Page 1-10
• Pipe: Schedule 10, Grooved Pipes 1¼” and larger, Manufacturer: Allied or Equal
• Pipe: Schedule 40, Threaded pipes up to 1½”, Manufacturer: Allied or Equal
• Grooved Fittings, grooved pipes only, Manufacturer: Anvil SPF or Victaulic
• Screwed Fittings, threaded pipes only, Ductile Iron, Manufacturer: Anvil SPF Ductile or Equal
- Hangers and Supports ----------------------------------------------------------------- Page 11-13
• Rings, Beam Clamps, Rods, Manufacturer: Anvil
- Sprinkler Heads ----------------------------------------------------------------------- Page 14-23
• Fire Sprinklers, Quick Response: Concealed, Pendent, Upright, and Horizontal Sidewall;
Manufacturer: Reliable
Schedule-10/Schedule-40 – M-COAT
®
Submittal Data Sheet
Fully Listed and FM Approved Sprinkler Pipe
When you specify Schedule-10/Schedule-40 – M-COAT® sprinkler pipe from Allied Tube
& Conduit, you get UL listed and FM approved products. Although these products do
not require separate approvals, Schedule-10/Schedule-40 – M-COAT gives you the extra
quality assurance you demand. Our Sch-10 (1-1⁄4” – 8”) pipe and Sch-40 (1” – 2-1⁄2”)
pipe have passed the same thorough lab testing as our other listed pipe products, and
receive periodic mill inspections from both UL and FM agents to ensure consistent quality.
Galvanized Pipe Schedule-10/Schedule-40 – M-COAT product can be
“hot-dip” galvanized to meet FM requirements.
Superior Coating Our advanced formula mill coating offers a clean, durable
surface that is also paintready for custom color applications without special preparation.
The internal surface of all black Fire Sprinkler pipe up to 4.5000” in diameter shall be
coated with Allied Tube & Conduit Antibacterial Formula “M-COAT”.
American Made Able to meet “Buy American” requirements, and is available
through distributors in the USA, Canada, Mexico and Latin America.
Specifications & Approvals Schedule-10 – M-COAT pipe is in
compliance with ASTM A135, Type E Grade A, and NFPA 13. Schedule-40 – M-COAT
pipe is in compliance with ASTM A135/A795, Type E Grade A, and NFPA 13.
Both pipe products have a working pressure rating of 300 psi maximum and also meet
the stringent requirement for the following tests: Welded Outlets, Hydrostatic Pressure,
Side Wall Rupture, Vibration Test.
Sch-40 – M-COAT Specifications
NPS Nominal I.D.
Wt.
Wt. (H20 Filled)
In; mm
In; mm
Lbs/Ft; kg/m Lbs/Ft; kg/m
1”
1.049
1.680
2.05
25
26.6
2.5
3.05
1¼”
1.380
2.270
2.93
32
35.1
4.36
4.36
1½”
1.610
2.720
3.61
40
40.9
4.0
5.37
2”
2.067
3.650
5.13
50
52.5
5.4
7.63
2½”
2.469
5.790
7.86
65
62.7
8.6
11.73
CRR
–
1
–
1
–
1
–
1
–
1
–
Sch-10 – M-COAT Specifications
NPS Nominal I.D.
Wt.
Wt. (H20 Filled)
In; mm
In; mm
Lbs/Ft; kg/m Lbs/Ft; kg/m
1¼”
1.442
1.810
2.525
32
36.6
2.7
3.75
1½”
1.682
2.080
3.04
40
42.7
3.1
4.52
2”
2.157
2.640
4.22
50
54.8
3.9
6.28
2½”
2.635
3.530
5.89
65
66.9
5.3
8.77
3”
3.260
4.330
7.94
75
82.8
6.4
11.82
4”
4.260
5.610
11.78
100
108.2
8.3
17.53
5”
5.295
7.77
17.33
125
134.5
11.56
25.80
6”
6.357
9.290
23.03
150
161.5
13.8
34.27
8”
8.249
16.490
40.15
200
209.5
24.5
59.75
CRR
–
7.0955
–
5.6570
–
4.5827
–
3.5196
–
2.5550
–
1.6020
–
1.4874
–
1.0251
–
1.8365
–
Project:
Sprinkler Contractor:
Date:
Engineer:
Specification Reference: System Type:
Locations:Comments:
Customer Service (800) 882-5543 Fax: (800) 659-7730
• 16100 S Lathrop Ave. Harvey, IL 60426 • 11350 Norcom Rd. Philadelphia, PA 19154
• 2525 N 27th Ave. Phoenix, AZ 85009
www.alliedtube-sprinkler.com
• 600 Dean Sievers Place
Morrisville, PA 19067
©2011 Atkore International, Inc. All Rights Reserved. STP-S5-4M-1111
FIG. SE-1
Short Pattern 90˚ Elbow
SE-1 are short pattern products and are specifically designed for
use in Fire Protection applications where economy is a factor. All
products are is UL/ULC Listed, LPCB, VdS and FM Approved.
Maximum working pressure for these products is 300 PSI. For
the latest UL/ULC listed, LPCB, VdS and FM Approved pressure
ratings versus pipe schedule, see www.anvilintl.com or contact
your local Anvil Representative.
C to E
O.D.
VdS
For Listings/Approval Details and Limitations, visit our website at
www.anvilintl.com or contact an Anvil® Sales Representative.
SE-1 90˚ ELBOW
MATERIAL SPECIFICATIONS
Nominal
Size
O.D.
Center
to End
Approx.
Wt. Ea.
In./DN(mm)
In./mm
In./mm
Lbs./Kg
CAST FITTINGS:
Ductile Iron conforming to ASTM A-536, Grade 65-45-12
COATINGS:
q Rust inhibiting paint Color: ORANGE (standard) or
q Hot Dipped Zinc Galvanized conforming to ASTM A-153 (optional)
q Other available options: Example: RAL3000 or RAL9000 Series
2
2.375
23⁄4
1.5
50
60.3
70
0.7
21⁄2
2.875
3
2.1
65
73.0
76
1.0
3
3.500
33⁄8
3.6
80
88.9
86
1.6
4
4.500
4
5.8
100
114.3
102
2.6
6
6.625
51⁄2
11.8
150
168.3
140
5.3
18
8
8.625
67⁄8
21.1
16
200
219.1
175
9.6
Pressure Drop
(ft. of Schedule 40 pipe)
Additional sizes available, contact an Anvil Representative.
SE-1 90˚ Elbow short pattern fitting –
pressure drop
8 inch
6 inch
4 inch
3 inch
21/2 inch
2 inch
14
12
10
8
6
4
2
0
5
10
15
20
Flow Rate (ft./sec.)
SPF™ short pattern fittings exceed the headloss requirements of NFPA 13.
For Fig. SE-1 90˚ grooved end elbows use the value shown.
Note: Above values are shown for Schedule 40 pipe to be consistent with industry practices.
PROJECT INFORMATION
APPROVAL STAMP
Contractor:
q Approved
q Approved as noted
q Not approved
Engineer:
Remarks:
Project:
Address:
Submittal Date:
Notes 1:
Notes 2:
FP-4.12
FIG. ST-1
Short Pattern Tee
ST-1 are short pattern products that are specifically designed for use in Fire
Protection applications where economy is a factor. All products are UL/ULC
Listed, LPCB, VdS and FM Approved.
Maximum working pressure for these products is 300 PSI. For the latest UL/
ULC listed, LPCB, VdS and FM Approved pressure ratings versus pipe
schedule, see www.anvilintl.com or contact your local Anvil Representative.
C to E
O.D.
VdS
C to E
For Listings/Approval Details and Limitations, visit our website at
www.anvilintl.com or contact an Anvil® Sales Representative.
ST-1 TEE
MATERIAL SPECIFICATIONS
Nominal
Size
O.D.
Center
to End
Approx.
Wt. Ea.
In./DN(mm)
In./mm
In./mm
Lbs./Kg
2
2.375
23⁄4
2.9
50
60.3
70
1.3
21⁄2
2.875
3
4.6
65
73.0
76
2.1
3
3.500
33⁄8
6.9
80
88.9
86
3.1
4
4.500
4
10.9
100
114.3
102
4.9
25.0
CAST FITTINGS:
Ductile Iron conforming to ASTM A-536
COATINGS:
q Rust inhibiting paint Color: ORANGE (standard) or
q Hot Dipped Zinc Galvanized conforming to ASTM A-153 (optional)
q Other available options: Example: RAL3000 or RAL9000 Series
ST-1 90˚ Tee short pattern fitting –
pressure drop
6.625
5 ⁄2
168.3
140
11.3
18
8
8.625
67⁄8
42.1
16
200
219.1
175
19.1
Pressure Drop
(ft. of Schedule 40 pipe)
6
150
1
8 inch
6 inch
4 inch
3 inch
21/2 inch
2 inch
14
12
10
8
6
4
2
0
5
10
15
20
Flow Rate (ft./sec.)
SPF™ short pattern fittings exceed the headloss requirements of NFPA 13.
For Fig. ST-1 grooved end tee branch use 21/2 times the value shown.
For Fig. ST-1 grooved end tee run use the value shown.
Note: Above values are shown for Schedule 40 pipe to be consistent with industry practices.
PROJECT INFORMATION
APPROVAL STAMP
Contractor:
q Approved
q Approved as noted
q Not approved
Engineer:
Remarks:
Project:
Address:
Submittal Date:
Notes 1:
Notes 2:
FP-4.12
FIG. SK-1
Cap
E to E
SK-1 GROOVED CAP
Nominal
Size
O.D.
End
to End
Approx.
Wt. Ea.
In./DN(mm)
In./mm
In./mm
Lbs./Kg
0.3
1
1.315
11⁄4
25
33.4
25
0.1
11⁄4
1.660
1
0.4
32
42.2
25
0.2
1
1 ⁄2
1.900
1
0.5
40
48.3
25
0.2
0.7
2
2.375
1
50
60.3
25
0.3
21⁄2
2.875
1
1.0
65
3 O.D.
73.0
3.000
25
1
0.4
0.9
76.1
3
76.1
3.500
25
1
0.4
1.5
80
88.9
25
0.7
4
4.500
11⁄16
2.7
100
114.3
27
1.2
5
5.563
11⁄16
4.4
125
61⁄2 O.D.
141.3
6.500
27
1
2.0
5.5
165.1
6
165.1
6.625
25
11⁄16
2.5
6.6
150
168.3
27
3.0
8
8.625
13⁄16
11.3
200
219.1
30
5.1
10*
10.750
11⁄4
21.0
250
273.1
32
9.5
12*
12.750
11⁄4
35.5
300
323.9
32
16.1
VdS
For Listings/Approval Details and Limitations, visit our website at
www.anvilintl.com or contact an Anvil® Sales Representative.
MATERIAL SPECIFICATIONS
CAST FITTINGS:
Ductile Iron conforming to ASTM-A536
COATINGS:
q Rust inhibiting paint Color: ORANGE (standard) or
q Hot Dipped Zinc Galvanized conforming to ASTM A-153 (optional)
q Other available options: Example: RAL3000 or RAL9000 Series
*Supplied as Style K-1 only.
PROJECT INFORMATION
APPROVAL STAMP
Contractor:
q Approved
q Approved as noted
q Not approved
Engineer:
Remarks:
Project:
Address:
Submittal Date:
Notes 1:
Notes 2:
FP-4.12
FIG. C-3
Lightweight Flexible Coupling
The C-3 Coupling is a flexible light weight style which is
ideal for fire protection services and other services where low
pressure and ambient temperature conditions are expected.
For the latest UL/ULC listed, LPCB, VdS and FM Approved
pressure ratings versus pipe schedule, see www.anvilintl.com
or contact your local Anvil Representative.
VdS
For Listings/Approval Details and Limitations, visit our website at
www.anvilintl.com or contact an Anvil® Sales Representative.
MATERIAL SPECIFICATIONS
HOUSING:
GASKETS: Materials
Ductile Iron conforming to ASTM A-536, Grade 65-45-12
Properties as designated in accordance with ASTM D-2000.
ANSI BOLTS & HEAVY HEX NUTS:
q Pre-Lubricated Grade “E” EPDM, Type A Gasket (Violet color code)
Heat treated, oval-neck track head bolts conforming to ASTM A-183
Grade 2 with a minimum tensile strength of 110,000 psi and heavy hex nuts
of carbon steel conforming to ASTM A-563 Grade A or Grade B, or SAE
J995 Grade 2. Bolts and nuts are provided zinc electroplated as standard.
METRIC BOLTS & HEAVY HEX NUTS:
Heat treated, zinc electroplated oval-neck track head bolts made of carbon
steel with mechanical properties per ISO 898-1 Class 8.8. Hex nuts and
bolts are zinc electroplated followed by a yellow chromate dip.
COATINGS:
q Rust inhibiting paint Color: ORANGE (standard)
q Hot Dipped Zinc Galvanized (optional)
q Other available options: Example: RAL3000 or RAL9000 Series
For other coating requirements contact an Anvil Representative.
LUBRICATION:
q Standard Gruvlok
q Gruvlok Xtreme™ required for dry pipe systems and freezer applications.
-40°F to 150°F (Service Temperature Range)(-40°C to 65°C)
Recommended for wet and dry (oil free air) pipe fire protection sprinkler systems. For dry pipe systems and freezer applications, Gruvlok Xtreme™ Lubricant is required.
q Grade “E” EPDM (Green color code)
-40°F to 230°F (Service Temperature Range)(-40°C to 110°C)
Recommended for water service, diluted acids, alkalies solutions, oil-free air and many chemical services.
NOT FOR USE IN PETROLEUM APPLICATIONS.
q Grade “EP” EPDM (Green and Red color code)
-40°F to 250°F (Service Temperature Range)(-40°C to 121°C)
Recommended for water service, diluted acids, alkalies solutions, oil-free air and many other chemical services.
NOT FOR USE IN PETROLEUM APPLICATIONS.
GASKET TYPE:
q Standard C Style
q Flush Gap
PROJECT INFORMATION
APPROVAL STAMP
Contractor:
q Approved
q Approved as noted
q Not approved
Engineer:
Remarks:
Project:
Address:
Submittal Date:
Notes 1:
Notes 2:
FP-4.12
FIG. C-3
Lightweight Flexible Coupling
Z
Y
X
C-3 LIGHTWEIGHT FLEXIBLE COUPLING
Deflection From CL
Max.
Range of
Max. End
Working
Pipe End
Load
Pipe
Pressures
Separation Per Coupling
Nominal
Size
Pipe
O.D.
In./DN(mm)
In./mm
PSI/bar
Lbs./kN
In./mm
Degrees
1
1.315
300
407
0-1⁄32
1° 22'
25
33.4
20.7
1.81
0-0.79
11⁄4
1.660
300
649
0-1⁄32
32
42.2
20.7
2.89
0-0.79
11⁄2
1.900
300
851
0-1⁄32
40
48.3
20.7
3.78
0-0.79
2
2.375
300
1,329
0-1⁄32
Coupling Dimensions
X
Y
Z
Coupling Bolts
Qty.
In./Ft. - mm/m In./mm In./mm In./mm
0.29
21⁄2
4
13⁄4
23.8
64
102
44
1° 5'
0.23
23⁄4
41⁄4
13⁄4
18.8
70
111
44
0° 57'
0.20
3
41⁄2
13⁄4
16.5
76
117
44
0° 45'
0.16
33⁄8
5
17⁄8
In./mm
2
2
2
2
50
60.3
20.7
5.91
0-0.79
13.1
66
140
48
21⁄2
2.875
300
1,948
0-1⁄32
0° 37'
0.13
37⁄8
51⁄2
17⁄8
2
65
3 O.D.
73.0
2.996
20.7
300
8.66
2,115
0-0.79
0-1⁄32
0° 36'
10.9
0.13
99
41⁄8
146
53⁄4
48
17⁄8
76.1
3
76.1
3.500
20.7
300
9.41
2,886
0-0.79
0-1⁄32
0° 31'
10.4
0.11
105
41⁄2
146
61⁄8
48
17⁄8
M10 x 50
40
60
0.6
⁄8 x 21⁄4
30
45
1.5
3
M10 x 50
40
60
0.7
⁄8 x 21⁄4
30
45
1.7
3
2
M10 x 57
1
⁄2 x 21⁄2
40
30
60
45
0.9
2.6
156
48
61⁄8
8
21⁄4
2
100
51⁄2 O.D.
114.3
5.500
20.7
300
21.22
7,127
0-2.38
0-3⁄32
0° 59'
55.5
0.54
156
67⁄8
203
95⁄16
57
21⁄4
139.7
5
139.7
5.563
20.7
300
31.70
7,292
0-2.38
0-3⁄32
0° 58'
45.4
0.54
175
7
237
95⁄16
125
61⁄2 O.D.
141.3
6.500
20.7
300
32.44
9,955
0-6.4
0-3⁄32
0° 50'
45
0.46
178
77⁄8
165.1
6
165.1
6.625
20.7
300
44.28
10,341
0-2.38
0-3⁄32
0° 49'
34.8
0.45
200
81⁄4
37.8
210
273
57
0° 37'
0.35
105⁄8
131⁄2
21⁄2
29.1
270
343
64
0-2.38
1.3
0.9
1.9
114
77.97
45
60
45
8.9
20.7
30
40
30
0.67
219.1
0.5
⁄8 x 21⁄4
3
1.2
M10 x 57
3
⁄8 x 21⁄4
1° 12'
200
60
2
0-3⁄32
0-3⁄32
40
0.8
0-0.79
0-2.38
M10 x 57
2.0
12.84
46.00
45
60
4,771
17,528
30
45
20.7
20.7
⁄8 x 21⁄4
40
300
300
Lbs./Kg
3
30
88.9
168.3
Ft.-Lbs./N-m
Approx.
Wt. Ea.
⁄8 x 21⁄4
4.500
8.625
Max.
3
4
8
Min.
M10 x 57
80
150
Size
Specified Torque §
M10 x 63
40
60
1.2
5
⁄8 x 31⁄2
80
100
4.1
2
M12 x 70
5
⁄8 x 31⁄2
110
100
150
130
1.9
5.5
57
21⁄4
2
M16 x 89
5
⁄8 x 31⁄4
135
100
175
130
2.5
5.7
237
101⁄2
57
21⁄4
2
M16 x 85
5
⁄8 x 31⁄4
135
100
175
130
2.6
6.1
267
103⁄4
57
21⁄4
2
M16 x 85
5
⁄8 x 31⁄4
135
100
175
130
2.8
6.1
2
M16 x 85
135
175
2.8
⁄4 x 41⁄4
130
180
11.9
M20 x 110
175
245
5.4
3
Range of Pipe End Separation and Angular Deflection values are for roll grooved pipe and may be doubled for cut groove pipe.
1. Working pressure and/or end load are total allowable, based on standard weight steel pipe, roll or cut grooved.
2. One time field test pressure may be increased to 1.5 times the figures listed above.
§ – For additional Bolt Torque information see Technical Data Section.
s – Working Pressure Ratings are for reference only and based on Sch. 40 pipe. For the latest UL/ULC, FM, VdS and LPCB pressure FP-4.12
ratings versus pipe schedule, please visit anvilintl.com or contact your local Anvil Representative.
For dry pipe systems and freezer applications
lubrication of the gasket is required,
Gruvlok® Xtreme™ Lubricant is required.
Print
http://www.anvilintl.com/ProductSearch/PrintProduct.aspx?lid=1962
Page 1 of 1
9/26/2011
Print
http://www.anvilintl.com/ProductSearch/PrintProduct.aspx?lid=1965
Page 1 of 1
9/26/2011
Print
http://www.anvilintl.com/ProductSearch/PrintProduct.aspx?lid=1966
Page 1 of 1
9/26/2011
Print
http://www.anvilintl.com/ProductSearch/PrintProduct.aspx?lid=1969
Page 1 of 1
9/26/2011
PIPE RINGS
Fig. 69
Adjustable Swivel Ring, Tapped Per NFPA Standards
Size Range: 1⁄2" through 8"
Material: Carbon steel
Finish: Galvanized
Service: Recommended for suspension of non-insulated stationary pipe line.
Maximum Temperature: 650° F
Approvals: Complies with Federal Specification A-A-1192A (Type 10), WW-H-171-E (Type 10),
ANSI/MSS SP-69 and MSS SP-58 (Type 10). UL Listed and FM Approved (Sizes 3⁄4" - 8").
Features:
• Threads are countersunk so that they cannot become burred or damaged.
• Knurled swivel nut provides vertical adjustment after piping is in place.
• Captured swivel nut in the 1⁄2" through 6" sizes. The capture is permanent in the bottom
portion of the band, allowing the hanger to be opened during installation if desired, but
not allowing the nut to fall completely out.
Ordering: Specify size, figure number and name.
Note: The acceptability of galvanized coatings at temperatures above 450°F is at the discretion
of the end user.
Metric nut available upon request. Non-captured nut also available upon request.
A
B
F
Fig. 69: Loads (lbs) • Weight (lbs) • Dimensions (in)
Pipe Size Max Load Weight
1
⁄2
3
⁄4
1
11⁄4
11⁄2
2
21⁄2
3
4
5
6
8
300
525
650
1,000
0.10
0.10
0.10
0.10
0.10
0.11
0.20
0.20
0.30
0.54
0.65
1.00
Rod Size
A
3
⁄8
1
⁄2
B
C
F
27⁄8
23⁄4
29⁄16
25⁄8
23⁄4
31⁄4
4
313⁄16
411⁄16
55⁄16
611⁄16
8
2
17⁄8
111⁄16
13⁄4
17⁄8
23⁄8
23⁄4
215⁄16
313⁄16
43⁄8
59⁄16
7
19⁄16
15⁄16
1
G
Width
CL
G
1
/2" through 1" pipe
5
/8
7
⁄8
A
11⁄8
15⁄16
13⁄16
19⁄16
21⁄4
211⁄16
C
F
3
/4
1
C B
CL
Note: Reflects changes in rod diameter from previously published data per recent revisions in MSS-SP-58 & 69
G
11/4" through 8" pipe
PROJECT INFORMATION
APPROVAL STAMP
Contractor:
q Approved
q Approved as noted
q Not approved
Engineer:
Remarks:
Project:
Address:
Submittal Date:
Notes 1:
Notes 2:
PH-11.11
BEAM CLAMPS
Fig. 92
Universal C-type Clamp (Standard Throat)
Size Range: 3⁄8" and 1⁄2"
Material: Ductile iron, hardened steel cup point set screw and locknut.
Finish: TPlain or TGalvanized
Service: Recommended for use under roof installations with bar joist type construction,
or for attachment to the top or bottom flange of structural shapes where the
vertical hanger rod is required to be offset from the edge of the flange and where
the thickness of joist or flange does not exceed 3⁄4".
Approvals: Complies with Federal Specification A-A-1192A (Type 19 & 23)
WW-H-171-E (Type 23), ANSI/MSS SP-69 and MSS SP-58 (Type 19 & 23).
UL, ULC Listed and FM Approved.
How to size: Size of clamp is determined by size of rod to be used.
Installation: Follow recommended set screw torque values per MSS-SP-69
(See table on page 233)
Features:
• They may be attached to horizontal flanges of structural members in either the top beam or
bottom beam positions.
• Secured in place by a cup-pointed Set Screw tightened against the flange.
A Jam Nut is provided for tightening the Set Screw against the Body Casting.
• Thru tapping of the body casting permits extended adjustment of the threaded rod.
• Can be used with Fig 89X retaining clip for seismic applications.
Ordering: Specify rod size, figure number, name of clamp and finish.
H
C
F
E
AT LEAST ONE
FULL THREAD
OF ROD MUST
BE EXPOSED
G
3⁄4"
D
BODY
CASTING
A
JAM - NUT
SET SCREW
1"
FIG. 92: LOAD (LBS) • WEIGHT (LBS) • DIMENSIONS (IN) • TORQUE (IN-LBS)
Rod Size Set Screw
A
Size
3
3
1
1
⁄8
⁄2
■
Torque
Value
⁄8
⁄2
60
125
Max Loads ■
Top
Bottom
500
950
250
760
Weight
C
D
0.34
0.63
15⁄16
13⁄8
19⁄16
113⁄16
E
9
⁄16
⁄2
1
F
G
13
3
1
1
7
23
⁄16
1 ⁄16
⁄8
⁄16
Maximum temperature of 450° F
PROJECT INFORMATION
APPROVAL STAMP
Contractor:
TApproved
TApproved as noted
TNot approved
Engineer:
Remarks:
Project:
Address:
Submittal Date:
Notes 1:
Notes 2:
PH-11.11
H
⁄2
⁄32
HANGER RODS
Fig. 146
Continuous Threaded Rod
Size Range: 1⁄4" through 1 1⁄2" Stocked in six, ten, and twelve foot
lengths. Other even foot lengths can be furnished to order.
Material: Carbon steel or Stainless Steel Gr 304
Threads: National Coarse (USS), rod threaded complete length.
Finish: TPlain or TGalvanized.
Maximum Temperature: 650° F.
Ordering: Specify rod diameter and length, figure number,
name and finish.
Note: The acceptability of galvanized coatings at temperatures
above 450°F is at the discretion of the end user.
FIG. 146:
LOADS (LBS) • WEIGHTS (LBS) • DIMENSIONS (IN)
Rod Size
A
1
Length
⁄4
⁄8
1
⁄2
5
⁄8
3
⁄4
7
⁄8
1
11⁄4
11⁄2
3
A
Threads
per Inch
Max Load
650˚ F
Weight
per Ft.
20
16
13
11
10
9
8
7
6
240
730
1,350
2,160
3,230
4,480
5,900
9,500
13,800
0.12
0.30
0.53
0.84
1.20
1.70
2.30
3.60
5.10
Note: Other rod sizes available upon request. Class 2 fit is available upon request.
PROJECT INFORMATION
APPROVAL STAMP
Contractor:
TApproved
TApproved as noted
TNot approved
Engineer:
Remarks:
Project:
Address:
Submittal Date:
Notes 1:
Notes 2:
PH-11.11
Bulletin 014 Rev. J
Bulletin 014 Rev. J
Model F1FR Series
Quick Response
Standard Spray
Model F1FR56 Sprinkler Types
Standard Upright
Standard Pendent
Conventional
Vertical Sidewall
Horizontal Sidewall
Model F1FR56 Recessed Sprinkler Types
Standard Pendent/F1/F2/FP
Horizontal Sidewall
Upright
Pendent
Conventional
Vertical Sidewall
Horizontal Sidewall
Recessed
Pendent/F1/F2
Recessed
Horizontal Sidewall
Concealed
Pendent
Recessed
Pendent/FP
XLH Upright
XLH Pendent
XLH Recessed
Pendent F1/F2
Model F1FR56 Concealed Sprinkler Types
Standard Pendent
Model F1FR42, F1FRXLH & F1FR28 Sprinkler
Types
Standard Upright
Standard Pendent
Model F1FR42, F1FRXLH & F1FR28 Recessed
Sprinkler Types
Standard Pendent
Model F1FR56LL & F1FR42LL Low Lead Sprinkler
Types*
Standard Pendent
Less than 0.25% Lead Content
Listing & Approvals
1. Underwriters Laboratories Inc. and Certified for
Canada (cULus).
2. Factory Mutual Approvals (FM)
3. Loss Prevention Council (LPCB, UK)
4. VdS Schadenverhütung GmbH
5. *NSF Certified to NSF/ANSi Standard 61 Annex G
UL Listing Category
Sprinklers, Automatic & Open (VNIV)
Quick Response Sprinkler
Product Description
Reliable Models F1FR56, F1FR56LL, F1FR42, F1FR42LL,
F1FRXLH & F1FR28 Series Sprinklers are quick response
sprinklers which combine the durability of a standard sprinkler with the attractive low profile of a decorative sprinkler.
The Models F1FR56, F1FR56LL, F1FR42, F1FR42LL,
F1FRXLH & F1FR28 Series Recessed automatic sprinklers
utilize a 3.0 mm frangible glass bulb. These sprinklers have
demonstrated response times in laboratory tests which are
five to ten times faster than standard response sprinklers.
This quick response enables the Model F1FR56, F1FR56LL,
F1FR42, F1FR42LL, F1FRXLH & F1FR28 Series sprinklers
to apply water to a fire much faster than
standard sprinklers of the same temperature rating.
The glass bulb consists of an accurately controlled amount of special fluid
hermetically sealed inside a precisely
manufactured glass capsule. This glass
XLH Recessed
bulb is specially constructed to provide
Pendent FP
fast thermal response.
At normal temperatures, the glass bulb contains the fluid
in both the liquid and vapor phases. The vapor phase can
be seen as a small bubble. As heat is applied, the liquid
expands, forcing the bubble smaller and smaller as the liquid pressure increases. Continued heating forces the liquid
to push out against the bulb, causing the glass to shatter,
opening the waterway and allowing the deflector to distribute the discharging water.
The Reliable Automatic Sprinkler Co., Inc., 103 Fairview Park Drive, Elmsford, New York 10523
Application
Quick response sprinklers are used in fixed fire protection systems: Wet, Dry, Deluge or Preaction. Care must be
exercised that the orifice size, temperature rating, deflector style and sprinkler type are in accordance with the latest
published standards of the National Fire Protection Association or the approving Authority Having Jurisdiction. Quick
response sprinklers are intended for installation as specified in NFPA 13. Quick response sprinklers and standard response sprinklers should not be intermixed.
Model F1FR42, F1FRXLH Upright
Technical data:
Models
Discharge Coefficient
F1FR56
**F1FR56LL(1)
K 5.6
F1FR42
**F1FR42LL(1)
F1FRXLH
K 4.2
F1FR28
K 2.8
(1)
Response
Quick
Response
Thread
Size
1/2” NPT
(R1/2)
Max.
Working
Pressure
Min.
Working
Pressure
Temperature
Rating
Finish
175 PSI
7 PSI
See
“Temperature
Ratings” Table.
See
“Finish Table”
Low Lead Sprinklers available only with Temperature Rating 200°F/93°C
Material Data:
Frame
Deflector
Load Screw
*Pintle
Cup
Washer
Bulb
DZR Brass
QM Brass
**Low Lead Brass
CDA Alloy 260,
CDA Alloy 220
or
CDA Alloy510
CDA Alloy 360
or
CDA Alloy 544
CDA Alloy 360
or
CDA Alloy 544
CDA Alloy 651
or
CDA Alloy 693
Nickel Alloy 440 or Alloy 360
coated with PTFE Adhesive
Tape
Glass
2.
Model F1FR56, Upright, Pendent & Conventional Sprinklers
Model F1FR42, F1FRXLH & F1FR28 Upright & Pendent Sprinklers
Installation Wrench: Model D Sprinkler Wrench
Installation Data:
Thread
Nominal
Orifice
Size
Nominal K Factor
US
Metric
Sprinkler
Approval
Height
Organization
Sprinkler Identification Number
(SIN)
Upright
Pendent
Standard-Upright (SSU) and Pendent Deflectors Marked to Indicate Position
1/2” (15mm)
1/2” NPT (R1/2)
5.6
80
2.25” (57mm)
1,2,3,4
RA1425(1)(2)(3)
RA1414(1)(2)(3)
7/16” (10mm)
1/2” NPT (R1/2)
4.2
60
2.25” (57mm)
1
RA1423(1)
RA1413
3/8” (10mm)
1/2” NPT (R1/2)
2.8
40
2.25” (57mm)
1
RA1421
RA1411
(1)
(1)
Conventional-Install in Upright or Pendent Position
15mm
1/2” NPT (R1/2)
(1)
5.6
80
57mm
3, 4
RA1475(3)
cULus listed corrosion resistant (Polyester coated) sprinkler.
Polyester coated FM approved sprinkler.
(3)
Polyester coated LPCB & VdS approved sprinkler RA1425, RA1414 & RA1475.
(1)
(2)
Conventional
Pendent
Upright
Model F1FR56LL & F1FR42LL Pendent Sprinklers
Installation Wrench: Model D Sprinkler Wrench
Installation Data:
Thread
Nominal
Orifice
Size
Nominal K Factor
US
Metric
Sprinkler
Approval
Sprinkler Identification Number
(SIN)
Height
Organization
Pendent
Standard-Pendent Deflectors Marked to Indicate Position
1/2” (15mm)
(1)
7/16” (11mm)
(1)
1/2” NPT (R1/2)
5.6
80
2.25” (57mm)
1,5
RA1414
1/2” NPT (R1/2)
4.2
60
2.25” (57mm)
1,5
RA1413
cULus listed corrosion resistant (Polyester coated) sprinkler.
3.
Model F1FR56, F1FR42, F1FRXLH & F1FR28 Quick Response Recessed Pendent Sprinkler(1)
Installation Wrench: Model GFR2 Sprinkler Wrench
Installation Data:
(1)
K Factor
Nominal
Orifice
Thread
Size
Metric
Sprinkler
Height
Sprinkler Identification Number
(SIN)
US
1/2” (15mm)
1/2” NPT(R½)
5.6
80
2.25” (57mm)
RA1414
7/16” (10mm)
3/8” (10mm)
1/2” NPT (R1/2)
4.2
60
2.25” (57mm)
RA1413
1/2” NPT (R1/2)
2.8
40
2.25” (57mm)
RA1411
Refer to escutcheon data table for approvals & dimensions
Model F1FR56LL & F1FR42LL Quick Response Recessed Pendent Sprinkler(1)
Installation Wrench: Model GFR2 Sprinkler Wrench
Installation Data:
(1)
K Factor
Nominal
Orifice
Thread
Size
US
Metric
Sprinkler
Height
Sprinkler Identification Number
(SIN)
1/2” (15mm)
1/2” NPT(R½)
5.6
80
2.25” (57mm)
RA1414
7/16” (10mm)
1/2” NPT (R1/2)
4.2
60
2.25” (57mm)
RA1413
Refer to escutcheon data table for approvals & dimensions
Model F1FR56, F1FR56LL, F1FR42, F1FR42LL, F1FRXLH &
F1FR28 F1 or F2
Model F1FR56, F1FR56LL, F1FR42, F1FR42LL, F1FRXLH &
F1FR28 FP
Model F1FR56 Quick Response Vertical Sidewall Sprinkler
Installation Wrench: Model D Sprinkler Wrench
Installation Position: Upright or Pendent
Approval Type: Light Hazard Occupancy
Installation Data:
(1)
(2)
Nominal K Factor
Nominal
Orifice
Thread Size
½” (15mm)
15mm
½” NPT (R1/2)
½” NPT (R1/2)
US
Metric
Sprinkler
Height
5.6
5.6
8.0
8.0
2.25” (57mm)
2.25” (57mm)
Approval
Organizations
Sprinkler
Identification
Numbers (SIN)
1,2,3,4
4(1)
RA1485(2)
LPC Approval is for pendent position only.
cULus Listed corrosion resistant (Polyester coated) sprinkler.
Vertical Sidewall
4.
Sprinkler Type
Deflector to Ceiling Distance
(Min. - Max.)
Upright
Pendent
4” (102mm) - 12” (305mm)
4” (102mm) - 12” (305mm)
Model F1FR56 Quick Response Horizontal Sidewall Sprinkler
Deflector: HSW
Installation Wrench: Model D Sprinkler Wrench
Installation Data: Horizontal Sidewall
Nominal K Factor
Nominal Orifice
½” (15mm)
(1)
(2)
Thread Size
½” NPT (R1/2)
US
Metric
5.6
80
Sprinkler
Height
2.63” (67mm)
Approval Organizations
and Type of Approval
Light Hazard
Ordinary
Hazard
1,2
1
Sprinkler
Identification
Numbers (SIN)
RA1435(1)(2)
cULus Listed corrosion resistant (Polyester coated) sprinkler.
Polyester coated FM approved sprinkler.
Horizontal Sidewall
Note: For Recessed HSW Sprinklers use installation wrench GFR2.
Model F1FR56 Quick Response Concealed Pendent Sprinklers
Installation Wrench: Model RC1 Sprinkler Wrench
Technical Data:
“K” Factor
Nominal
Orifice
US
½” (15mm)
Temp. Rating
Sprinkler
Cover
Max.
Ambient
Temp
F1FR
135°F/57°C
135°F/57°C
100°F/38°C
Orange
½” NPT
F1FR
155°F/68°C
135°F/57°C
100°F/38°C
Red
80
½” NPT
F1FR
175°F/79°C
165°F/74°C
100°F/38°C
80
½” NPT
F1FR
200°F/93°C
165°F/74°C
150°F/65°C
Metric
Thread
Size
Model
5.6
80
½” NPT
½” (15mm)
5.6
80
½” (15mm)
5.6
½” (15mm)
5.6
(1)
Bulb
Color
Approvals
Sprinkler
Identification
Number(SIN)
1
RA1414
1, 4
RA1414
Yellow
1
RA1414
Green
1
RA1414
(1)
For VdS only = 155°F/68°C Norbulb and 1/2” [12,7mm] adjustment.
Model F1FR56LL Quick Response Concealed Pendent Sprinklers
Installation Wrench: Model RC1 Sprinkler Wrench
Technical Data:
“K” Factor
Nominal
Orifice
US
Metric
½” (15mm)
5.6
80
Thread
Size
Temp. Rating
Model
Sprinkler
½” NPT F1FR56LL 200°F/93°C
Cover
Max.
Ambient
Temp
Bulb
Color
Approvals
Sprinkler
Identification
Number(SIN)
165°F/74°C
150°F/65°C
Green
1, 5
RA1414
5.
Figure 1
Figure 2
Installation Aid
gagement. A choice of two cover plate assemblies provide
either 1/2” (13mm) or 5/8” (8mm) of cover adjustment,
Do not install these sprinklers in ceiling which have positive
pressure in the space above.
After a 25/8” (67mm) diameter hole is cut in the ceiling, the
sprinkler is easily installed with the Model RC1 Wrench. A
Teflon* based thread sealant should be applied to the sprinkler threads only. The Model RC1 Wrench is then used to
engage the sprinkler wrenching surfaces and to install
the sprinkler in the fitting. When inserting or removing the
wrench from the sprinkler/cup assembly, care should be taken to prevent damage to the sprinkler. DO NOT WRENCH
ON ANY OTHER PART OF THE SPRINKLER. The cover
plate is then pushed onto the cup. Final adjustment is made
by hand turning the cover plate until the skirt flange makes
full contact with the ceiling. Cover plate removal requires
turning in the counter clockwise direction.
After installation, inspect all sprinklers to ensure that there
is a gap between the cover plate and ceiling and that the
four cup slots are open and free from any air flow impediment to the space above.
Concealed cover plate/cup assemblies are listed only for
use with specific sprinklers. The use of any other concealed
cover plate/cup assembly with the Model F1FR56 Pendent
Sprinkler or the use of the Model CCP Concealed cover
plate assembly on any sprinkler with which it is not specifically listed my prevent good fire protection and will void all
guarantees, warranties, listings and approvals.
Glass bulb sprinklers have orange bulb protectors to
minimize bulb damage during shipping, handling and installation. REMOVE THIS PROTECTION AT THE TIME THE
SPRINKLER SYSTEM IS PLACED IN SERVICE FOR FIRE
PROTECTION. Removal of the protectors before this time
may leave the bulb vulnerable to damage. RASCO wrenches are designed to install sprinklers when covers are in
place. REMOVE PROTECTORS BY UNDOING THE CLASP
BY HAND. DO NOT USE TOOLS TO REMOVE THE PROTECTORS.
A protective cap is included for use during installation.
Important: The F1FR56 Sprinkler with Model CCP cover
plate is not an FM Approved combination.
Installation
Quick response sprinklers are intended for installation as
specified in NFPA 13. Quick response sprinklers and standard response sprinklers should not be intermixed.
The Model F1FR56, F1FR56LL, F1FR42, F1FR42LL,
F1FRXLH & F1FR28 Recessed Quick Response Sprinklers are to be installed as shown. The Model F1 or F2 Escutcheons illustrated are the only recessed escutcheons
to be used with the Model F1FR56, F1FR56LL, F1FR42,
F1FR42LL, F1FRXLH & F1FR28 Sprinklers. The use of any
other recessed escutcheon will void all approvals and negate all warranties.
When installing Model F1FR56, F1FR56LL, F1FR42,
F1FR42LL, F1FRXLH & F1FR28 Sprinklers, use the Model
D Sprinkler Wrench. Use the Model GFR2 Wrench for installing F1FR56, F1FR56LL, F1FR42, F1FR42LL, F1FRXLH &
F1FR28 Recessed Pendent Sprinklers. Any other type of
wrench may damage these sprinklers.
NOTE: A leak tight ½” NPT (R1/2) sprinkler joint can be
obtained with a torque of 8-18 ft-lbs (10,8 - 24,4 N-m). Do
not tighten sprinklers over maximum recommended torque.
It may cause leakage or impairment of the sprinklers.
The Models F1FR56/CCP & F1FR56LL/CCP Concealed
Sprinkler use the ½” orifice, ½” NPT (R1/2), Model F1FR56
& F1FR56LL Pendent Sprinkler with a threaded Model CCP
cup which is factory attached to the sprinklers. The Model
F1FR56 Pndent is available in temperature rating of 135°F
(57°C), 155°F (68°C), 175°F (79°C) or 200°F (93°C). The
Model F1FR56LL Pendent is available only in a rating of
200°F (93°C). The concealed sprinkler assemblies are completed by the installation of the attractive low profile Model
CCP push on cover plate assembly, rated 135°F (57°C) or
165°F (74°C) for the F1FR56 and 165°F (74°C) for the FIFR56
LL. The cover plate and sprinkler cup assemblies are joined
using a cover plate skirt with flexible tabs for threaded en*DuPont Registered Trade Mark
6.
Finishes (1)
Temperature Ratings
Sprinkler
Max. Ambient
Classification Temperature
Bulb Color
Temp.
°C
°F
Ordinary
Ordinary
Intermediate
Intermediate
High (1)
(1)
57
68
79
93
141
135
155
175
200
286
100°F (38°C)
100°F (38°C)
150°F (66°C)
150°F (66°C)
225°F (107°C)
Sprinkler
Bronze
Chrome Plated
Polyester
Coated (4)(5)(6)
Orange
Red
Yellow
Green
Blue
Standard Finishes
Escutcheon
Brass
Chrome
Plated
White Painted
Cover plate(1)
Chrome
White
Special Application Finishes
Sprinkler
Escutcheon
Cover plate(1)
Bright Brass (3)
Black Plated
Black Paint (2)(6)
Off White (2)(6)
Satin Chrome
Not available for recessed sprinklers.
Escutcheon Data (1)
SIN RA1435 – cULus permits use with F1, F2 or FP escutcheons for “light
hazard” only, while FM limits use for same hazard with F2 escutcheon only.
(1)
Bright Brass
Black Plated
Black Paint
Off White
Satin Chrome
Bright Brass
Satin
Off White
Black Paint
Black Plated
Other finishes and colors are available on special order. Consult the
factory for details. Custom color painted sprinklers may not retain their
UL Corrosion resistance listing. Coverplate custom paint is semi-gloss,
unless specified otherwise.
(2)
cULus Listed only.
(3)
200°F (93°C) maximum.
(4)
cULus listed “corrosion resistance” applies to SIN Numbers RA1435
(HSW), RA1485(VSW), RA1425 (Upright), RA1414 (Pendent) and
RA1415 (Pendent) in standard black or white. Corrosion resistance in
other polyester colors is available upon request.
(5)
FM Approvals finish as “Polyester coated” applies to SIN Number
RA1414, RA1435 and RA1425 in standard black or white.
(6)
LPCB and VdS Approved finish applies only to RA1425, RA1414 and RA1475.
(1)
Maintenance
The Model F1FR56, F1FR56LL, F1FR42, F1FR42LL,
F1FRXLH and Model F1FR56, F1FR56LL, F1FR42,
F1FR42LL, F1FRXLH & F1FR28 Recessed Sprinklers should
be inspected quarterly and the sprinkler system maintained
in accordance with NFPA 25. Do not clean sprinklers with
soap and water, ammonia or any other cleaning fluids.
Remove dust by using a soft brush or gentle vacuuming.
Remove any sprinkler which has been painted (other than
factory applied) or damaged in any way. A stock of spare
sprinklers should be maintained to allow quick replacement
of damaged or operated sprinklers. Prior to installation,
sprinklers should be maintained in the original cartons and
packaging to minimize the potential for damage to sprinklers
that would cause improper operation or non-operation.
Ordering Information
Specify:
1. Sprinkler Model
2. Sprinkler Type
3. Orifice Size
4. Deflector Type
5. Temperature Rating
6. Sprinkler Finish
7. Escutcheon Type
8. Escutcheon Finish (where applicable)
9. Cover plate Model
10. Cover plate Thread size
11. Cover plate Temperature
12. Cover plate Adjustment
13. Cover plate Finish
Sprinkler Types
Standard Upright
Standard Pendent
Conventional
Recessed Pendent
Vertical Sidewall
Horizontal Sidewall
Recessed Horizontal sidewall
Concealed pendent
Note: When Model F1FR56 Recessed sprinklers are ordered, the sprinklers
and escutcheons are packaged separately.
Maximum Working Pressure
175 psi (12 bar)
100% Factory tested hydrostatically to 500 psi (34.5 bar)
7.
Reliable...For Complete Protection
Reliable offers a wide selection of sprinkler components. Following are some of the many
precision-made Reliable products that guard life and property from fire around the clock.
• Automatic sprinklers
• Deluge valves
• Flush automatic sprinklers
• Detector check valves
• Recessed automatic sprinklers
• Check valves
• Concealed automatic sprinklers
• Electrical system
• Adjustable automatic sprinklers
• Sprinkler emergency cabinets
• Dry automatic sprinklers
• Sprinkler wrenches
• Intermediate level sprinklers
• Sprinkler escutcheons and guards
• Open sprinklers
• Inspectors test connections
• Spray nozzles
• Sight drains
• Alarm valves
• Ball drips and drum drips
• Retarding chambers
• Control valve seals
• Dry pipe valves
• Air maintenance devices
• Accelerators for dry pipe valves
• Air compressors
• Mechanical sprinkler alarms
• Pressure gauges
• Electrical sprinkler alarm switches
• Identification signs
• Water flow detectors
• Fire department connection
The equipment presented in this bulletin is to be installed in accordance with the latest published Standards of the National Fire Protection Association, Factory
Mutual Research Corporation, or other similar organizations and also with the provisions of governmental codes or ordinances whenever applicable.
Products manufactured and distributed by Reliable have been protecting life and property for over 90 years, and are installed and serviced by the most highly
qualified and reputable sprinkler contractors located throughout the United States, Canada and foreign countries.
Manufactured by
The Reliable Automatic Sprinkler Co., Inc.
(800) 431-1588
Sales Offices
(800) 848-6051
Sales Fax
(914) 829-2042
Corporate Offices
www.reliablesprinkler.com Internet Address
Recycled
Paper
Revision lines indicate updated or new data.
EG. Printed in U.S.A. 02/13
P/N 9999970300