Innovation on Gas Analysis JCE-2 Ex Midi Sample Gas Cooler JCT Analysentechnik GmbH Gas Sampling Probes Heated Sample Lines Sample Gas Coolers Gas Converters Accessories APPLICATION FEATURES • For continuous gas conditioning in processes with dust and humidity • Removing water from gas sample • Reducing temperature of gas • Extractive gas analysis • Emission monitoring and process monitoring • For ATEX Zone II category 3 • Up to 2 separate gas streams • Continuously running compressor with hot gas by pass cooling system • Built-in condensate pump(s) • Proportional temperature control • Digital temperature display • Full protection coating of all copper parts • Stable dew point BENEFITS • Very low dissolution rates of water soluble gases • Safety for analysers • Small dead space in heat exchanger • Long lifetime also in harsh conditions • Rapid availability • Low and comfortable maintenance www.jct.at TECHNICAL DATA Cooling principle Compressor with hot gas bypass technology Number of gas paths 1-2 Operation PVDF Stainless steel Sample gas flow rate Mono* max. 250 l/h max. 500 l/h Sample gas flow rate Dual* max. 2 x 125 l/h max. 2 x 250 l/h max. +140°C max. +180°C max. +70°C max. +80°C Heat exchanger material Gas temperature sample gas inlet* Dew point sample gas inlet* Dew point sample gas outlet* +3°C Dew point stability (for constant inlet conditions) ±0,3 K Ambient temperature* +5....+40°C Cooler capacity Operating pressure without condensate pump 90 W 160 W 1,5 bar abs. 100 bar abs. Operating pressure with condensate pump 0,5 ... 1,5 bar abs. Ready for operation < 20 min Pressure drop at max. flow rate Mono 20 mbar 47 mbar Pressure drop at max. flow rate Dual (each gas path) 4,5 mbar 12 mbar Construction Dimensions over all (housing type S) 278 x 312 x 360 mm ( W x H x D ) Dimensions over all (housing type Q) 403 x 312 x 235 mm ( W x H x D ) Mounting position Stand alone or wall mount Alignment horizontal Weight approx. 19 kg Housing, colour Sheet steel 1,5 mm, powder coated, RAL 7035 Dead volume Mono 67 ml 67 ml Dead volume Dual 55 ml 55 ml Connection sample gas/ condensate outlet PVDF ID/OD 4/6 mm hose fitting Connection condensate outlet on bottom ID/OD 10/12 mm Type of protection Approval / Sign ID/OD 10/12 mm Ex II 3G Ex ma IIA T3 Ex II 3D Ex ma IIIB T180°C (IEC / EN60079) CE Electrical Supply voltage Option Power consumption (depending on load, ambient temperature and configuration) 230 VAC 50/60 Hz 115 VAC 50/60 Hz Supply connection / connection status contact approx. 2,3 m open wire ends Fusing approx. 190 VA External on installation site, fuse characteristic C: 230 VAC 6A; 115 VAC 10A Protection class IP 20 (EN 60529) On - time 100 % Alarm set points <0 / >+10°C Status / alarm relay Volt free change over contact Switching capacity relays max. 230 VAC/2A; min. 5 VADC 5mA *...may be affected by other values Page 2 GAS FLOW DIAGRAM A Gas heat exchanger B Condensate pump ORDERCODE Housing Heat exchanger Condensate pump Power supply Options for rear panel mounting S for side panel mounting Q 1 Mono PVDF heat exchanger 1 1 Mono SS heat exchanger 2 1 Mono glass heat exchanger 3 1 DUAL PVDF heat exchanger 4 1 DUAL SS heat exchanger 5 Without condensate pump JSR25 0 1 condensate pump JSR25 1 2 condensate pumps JSR25 2 230 VAC 50 / 60 Hz 1 115 VAC 50 / 60 Hz 3 Standard version X Special version (on request) 1 Order Code: JCE-2. Scope of delivery: device, operating manual Page 3 DIMENSIONS All dimensions in mm Specifications are subject to change without notice. PDS_E_JCE-2_v1.1 JCT Analysentechnik GmbH Werner Heisenberg-Straße 4 A-2700 Wiener Neustadt Tel. +43 (0) 2622 / 87201 Fax +43 (0) 2622 / 872011 E-Mail: [email protected] Web: www.jct.at Page 4