2.007 CLEAN CBEF IU MICRO-G AND SAMPLE TRAY
2.007 CLEAN CBEF IU MICRO-G AND SAMPLE TRAY (CBEF/18S-ALL/FIN/Payload/HC) Page 1 of 6 pages OBJECTIVE: Clean up inside of Cell Biology Experiment Facility (CBEF) Incubator Unit (IU) Micro-G. LOCATION: Saibo Rack (JPM1A2) DURATION: 25 minutes 10 minutes for preparation 15 minutes for Step 1 through 5 CREW: One PARTS: BZK Wipes P/N BCCK003 MATERIALS: Medium Glove or Large Glove P/N LSE-GV001 or LSE-GV002 1. PULLING OUT CBEF IU SAMPLE TRAY NOTE To maintain cleanliness, gloves must be worn when working inside CBEF Incubator Unit. 1.1 Don gloves. Figure 1. CBEF IU Handle Stopper 11 MAR 09 PGCF1044.xml 2.007 CLEAN CBEF IU MICRO-G AND SAMPLE TRAY (CBEF/18S-ALL/FIN/Payload/HC) CBEF IU Micro-G 1.2 Page 2 of 6 pages Unwrap Velcro strap from CBEF IU Micro-G Door Handle. Refer to Figure 1. 1.3 Slowly open CBEF IU Micro-G door. Engage CBEF IU Micro-G Door Handle to CBEF IU Door Handle Stay. Figure 2. GRIP POINT of CBEF IU Micro-G Sample Tray 1.4 Grab GRIP POINT. Refer to Figure 2. NOTE It is required to pull out CBEF IU Micro-G to hard stop. If CBEF IU Micro-G is latched halfway before hard stop, it will make it difficult to release side lock later. 1.5 2. 11 MAR 09 Pull out until hard stop of CBEF IU Micro-G Sample Tray. CLEANING UP CBEF IU MICRO-G SAMPLE TRAY PGCF1044.xml 2.007 CLEAN CBEF IU MICRO-G AND SAMPLE TRAY (CBEF/18S-ALL/FIN/Payload/HC) Page 3 of 6 pages Figure 3. Switch for CAN-1 to CAN-6, left and right wall, ceiling and floor of CBEF IU Micro-G 2.1 Safing ✓sw CAN-1 – OFF ✓sw CAN-2 – OFF ✓sw CAN-3 – OFF ✓sw CAN-4 – OFF ✓sw CAN-5 – OFF 11 MAR 09 PGCF1044.xml 2.007 CLEAN CBEF IU MICRO-G AND SAMPLE TRAY (CBEF/18S-ALL/FIN/Payload/HC) Page 4 of 6 pages ✓sw CAN-6 – OFF Refer to Figure 3. 2.2 Wipe CBEF IU Micro-G Sample Tray except connectors (6) and CBEF IU Temperature/Humidity Sensor with BZK Wipes. Refer to Figure 3. 2.3 Wipe GRIP POINT with BZK Wipes. Refer to Figure 3. NOTE CBEF IU Micro-G String Fan connector and cable are damageable. 2.4 Wipe right wall except CBEF IU Micro-G String Fan cables, and Temperature/Humidity Sensor with BZK Wipes. Refer to Figure 3. 2.5 Wipe bottom floor with BZK Wipes. Refer to Figure 3. 2.6 Wipe left wall with BZK Wipes except cable. Refer to Figure 3. 2.7 Wipe ceiling with BZK Wipes. Refer to Figure 3. 3. 11 MAR 09 STOWING CBEF IU SAMPLE TRAY PGCF1044.xml 2.007 CLEAN CBEF IU MICRO-G AND SAMPLE TRAY (CBEF/18S-ALL/FIN/Payload/HC) Page 5 of 6 pages Figure 4. Slide locks of CBEF IU Micro-G Sample Tray 3.1 Wipe slide locks with BZK Wipes. Refer to Figure 4. NOTE Slide locks are located in the middle of slide rail of CBEF IU Micro-G Sample Tray (Locations are above CAN-4 marking and below CAN-6 marking). It is required to release slide lock simultaneously by pushing in. Refer to Figure 4. 3.2 11 MAR 09 Release CBEF IU Micro-G Sample Tray slide locks (one each top and bottom) by simultaneously pressing slide locks and slide in a little until unlatched. Refer to Figure 4. *********************************************************************** PGCF1044.xml 2.007 CLEAN CBEF IU MICRO-G AND SAMPLE TRAY (CBEF/18S-ALL/FIN/Payload/HC) Page 6 of 6 pages * If sample tray is latched in the middle of the way, * * * Fully pull out until hard stop, then try again. * * *********************************************************************** 4. 3.3 Grab GRIP POINT. 3.4 Slide in CBEF IU Micro-G Sample Tray. WIPING AND CLOSING CBEF IU MICRO-G DOOR Figure 5. Rear surface of CBEF IU Micro-G door 4.1 Wipe rear surface of CBEF IU Micro-G door except for cable and ventilation valve with BZK Wipes. Refer to Figure 5. 4.2 Close CBEF IU Micro-G door. Securely wrap Velcro strap around the CBEF IU Micro-G Door Handle. 4.3 5. Doff gloves. CLOSE OUT 5.1 Update IMS or notify SSIPC to update IMS with stowage location. 5.2 Trash following items. Trash: BZK Wipes Medium Glove or Large Glove 11 MAR 09 PGCF1044.xml
© Copyright 2024