P: 724.625.0003 P: 800.308.6916 F: 724.625.3077 www.myerscoinc.com Email: [email protected] Myers & Co., Inc. 121 121 Seventh Seventh Avenue Avenue •• Valencia, Valencia, PA PA 16059 16059 SAMPLE CYLINDERS OAL SND B O.D. DOT-3E1800 THREAD NPT W.T. PROPERTIES: TABLE 1 No Description 1 2 3 4 5 HSSC15-1BA HSSC15-2BA HSSC15-3BA HSSC20-1BA HSSC20-2BA Pressure Rating DOT Min. Material (psi) Stand. Volume 316 SS 316 SS 316 SS 316 SS 316 SS 1800 1800 1800 1800 1800 3E 3E 3E 3E 3E 50 CC 75 CC 150 CC 300 CC 500 CC Max. Weight B OAL 0.5 LBS 1.64” 3.80” 0.6 LBS 2.72” 4.88” 0.5 LBS 6.09” 8.25” 1.8 LBS 6.79” 9.25” 2.5 LBS 11.42” 13.88” SND Thread (NPT) O.D. W.T. 0.72“ 0.72” 0.72” 0.74” 0.74” 1/4-18 1.5” 1/4-18 1.5” 1/4-18 1.5” 1/4-18 2.0” 1/4-18 2.0” .083” .083” .083“ .095” .095” SAMPLE CYLINDERS Sample Cylinders permit the safe extraction of a sample from a remote process location and provide safe containment for storage and transportation to laboratory for analysis. Stainless Steel Sample Cylinders are hot spun from seamless 316 stainless steel for maximum integrity and corrosion resistance. All cylinders are heat code traceable Inertium TM Surface Treatment All stainless steel cylinders and valves can be supplied with Inertium surface treatment for use in high sulfur applications. Inertium almost eliminates the interaction of fragile sulfur compounds with the valves and cylinders, improving sampling accuracy and precision, as well as extending the storage time. Cylinders are atomic cleaned before processing to remove any traces of contaminants or volatile chemicals that might interfere with the sampling. ADD “SI” to above part number for Inertium treatment. (see back for valves) VALVES FOR SAMPLE CYLINDERS We offer a wide variety of valve types and materials to fit your specific request. Series 314 Series 314RD ORDERING INFORMATION ORDERING INFORMATION VALVES Model 314-1 314-1-4D 314-13 314-13A Inlet Port 1/4 NPT Male 1/4 NPT Male 1/4 NPT Male 1/4 NPT Male Outlet Port 1/4 NPT Male 1/4 Tube Female 1/4 NPT Female 1/4 NPT Female VALVES WT .31 .36 .31 .31 Note: The above models ship with Buna-N O-Rings, Kel-F seats (without metal insert), black handles, and 303 stainless steel bodies, bonnets, and stems. The above models do not include dip tubes or rupture discs. To change the standard configuration add the following suffixes to the model number. 316 Stainless Body, Bonnet, and Stem Monel Body, Bonnet, and Stem Buna-N O-Rings for MTBE Service Kalrez™ O-Rings Ethylene Propylene O-Rings Viton O-Rings Teflon Seat Nylon Seat Seat with Metal Insert 2” Dip Tube 3 3/4” Dip Tube Red Handle (other colors available on special order) -768 -M -59 -08 -06 -12 -T -N -763 -2E -3 3/4 -R BONNET ASSEMBLIES Part Number Seat Material KA309 Kel-F (PCTFE) TA309 Teflon NA309 Nylon Note: If more than one modification is required, add dash code to model number in sequence listed. Dash codes also apply to bonnet assemblies where applicable. Model Number Inlet Port Outlet Port 314-1RD_______*** 1/4 NPT Male 1/4 NPT Male 314-13RD______*** 1/4 NPT Male 1/4 NPT Female 314-13ARD_____*** 1/4 NPT Male 1/4 NPT Female ***To complete the above Model Number, add the desired nominal burst pressure from the following standard choices 500, 1000, 1500, 1900, & 2850. Other burst pressures are available by special order. Selected burst pressure is etched on disc holder. Note: The above models ship with Buna-N O-Rings, Kel-F seats (without metal insert), black handles, and 303 stainless steel bodies, bonnets, and stems. The above models do not include dip tubes. To change the standard configuration - add the following dash codes to the model number: 316 Stainless Steel Body, Bonnet, and Stem Monel Body, Bonnet, and Stem Viton O-Rings Buna-N O-Rings for MTBE Service Kalrez™ O-Rings Ethylene Propylene O-Rings Teflon Seat Nylon Seat Seat with Metal Insert 2” Dip Tube 3 3/4” Dip Tube Red Handle (other colors available on special order) -768 -M -12 -59 -08 -06 -T -N -763 -2E -3 3/4 -R Note: If more than one modification is required, add dash code to model number in sequence listed. Dash codes also apply to Bonnet Assemblies and Rupture Disc Tees where applicable. RUPTURE DISC ASSEMBLIES The nominal rupture disc burst pressure should be at least 40% higher than the system operating pressure. Rupture disc burst pressure will be reduced by pulsating pressures, elevated temperature, and internal or external corrosion. In corrosive applications, regular inspections or pressure tests are necessary. Use of this rupture disc in vacuum or alternating vacuum/pressure applications may cause premature disc failure. When vented, the rupture unit presents a potential danger caused by noise and escaping pressure, chemicals or fragmented particles. The complete Rupture Disc Assembly consists of the disc, washer & holder. Each holder is etched with the nominal burst pressure and each disc is color coded for identification. To replace or inspect rupture disc: 1 - Remove holder, Disc, & Washer from valve body. 2 - Re-install or replace the washer & disc, then thread in the holder. Holder should be torqued per the following: Nominal Burst Pressure 500 1000 1500 1900 2850 Color Code Blue Red Yellow Green Orange Torque in Inch Pounds 40 75 120 140 215 Myers & Co., Inc. • 121 Seventh Avenue • Valencia, PA 16059 Phone: 724.625.0003 • Toll Free: 800.308.6916 • Fax: 724.625.3077 Web: www.myerscoinc.com • Email: [email protected] (see front for sample cylinders)