PWM Driver 5A-LP2 Product speciﬁcations 57 -OUT -OUT +OUT +OUT LLC- PWM5A-LP2 External signal input voltage DC 12 V External power input voltage 12-24V External power input current Max. 5A Output voltage Same as input voltage Output current Max. 5A Output gradation 1 KHz or less Output channels 1 channel Unit size (mm) 136 (H) x 57 (W) x 27 (H) Weight 170 g / unit Operating environment temperature Operating environment humidity 137 0 - 90% (no condensation) Indoors (LLC-PWM5A-LP2) PWM 入力 DC5V∼12V + 5 - Power Input DC12∼24V(5Amax) + Input / Output PWM Monitor DC5V∼12V LED lighting appliance dimming type Product firmly DC12V Flat FLEX FLEX α PROTERAS CO.,LTD. Luci Division Power supply PWM Light controller (LLC-PLC) Terminal block compatible wire AWG16~12 1.25sq~2.0sq DC12V dedicated power supply Product firmly DC24V Power FLEX Connect Power FLEX Connected Light Slim Light Indoor Slim Light Outdoor Line Light MUKU bar DC24V dedicated power supply Dimming type LP2 Product firmly DC24V Line Graze Indoor Line Graze Outdoor Disk DC24V dedicated power supply • To install the LLC-PWM5A-LP1, mount on a wall or other surface in the orientation shown in Fig. 1 or use in a location where dust does not accumulate on the terminal block. • The power equipment may occasionally cause a humming sound. The sound becomes louder as the load increases, so exercise caution in situations where quiet is necessary. • The unit generates heat. Install with a space of at least 100 mm around the unit in a non-airtight condition. When inserting and removing cables, be sure to firmly press the release button on the terminal block. To ensure safe usage The following is the safety cautions to prevent any harms or damages to others. If the product is used against cautions, it may cause damages･electrifications･smoke. Do not use in the following environments: Please use DC12-24V power supply. Do not use other power supplies such as AC100V. Please turn off all the powers when installation and inspection. Do not connect or disconnect the lead wires with its power on. Always use a conforming load at no more than the maximum number of connectable units. Dimming type LP1 Maker Wire stripping length (10mm) If the charges are in wrong direction, electric resistances will become hot and lighting will be destroied. 7.5 電源入力 Fig. 1 0 - 40°C PWM Dimming Driver 5A-LP2 PWM 調光ドライバー5A-LP2 ( LLC- PWM 5A-LP2) Before supplying power to this product, always check the polarities on the DC input side. Risk of product damage and accident if polarity is reversed, so exercise caution. 出力PWMモニタ Model Usage environment DC12~24V( 5Amax) Tokyo Japan Regional HQ Akasaka Bldg. 4F, 4-13-13, Akasaka, Minato-ku, Tokyo 107-0052, Japan Tel:+81-3-6327-7409 Fax:+81-3-6327-7410 Caution PWM 入力 DC5V∼12V 出力PWMモニタ PWM Dimming Driver 5A-LP2 電源入力 Φ5 27 Item / Product name PWM 調光ドライバー5A-LP2 ( LLC- PWM 5A-LP2) ■ Front view PROTERAS CO.,LTD. Luci Division Installation points DC12~24V( 5Amax) ■ Side view Instruction Manual ※unit of measure=mm ■ Top view Luci Pte. Ltd. Singapore World HQ 883 North Bridge Road, #07-03 Southbank, Singapore, 198785 Tel:+65-6291-2410 This product is for indoor use only. Install in a location that allows easy maintenance. Do not do the following to the lamp fitting: Never use the device with non-specified wire, incomplete connections, or bent wire tips. Risk of abnormal heat generation and fire. Use the wire indicated in the instructions, strip the indicated length of wire, and insert all the way into the wire hole. If the product becomes dirty, wipe with a dry cloth. Do not use organic volatile solvents such as thinner or benzene, and do not wash with water. Warranty The warranty period of this product is one year. If a product failure occurs during the warranty period and the product was used in accordance with the instructions, we will replace the product or repair it free of charge (this excludes on-site repair). - A location at high temperature (+40°C or higher) (operating environment temperature is 0°C to +40°C). - A location where water may splash on the product - A location with high humidity. - A dusty location. - A location with corrosive or inflammable gases. - A highly airtight location. - A location where the product is directly exposed to salt water or organic solvents. - A location where the product is exposed to direct sunlight. - A location subject to the effects of electric or magnetic fields. - A location subject to intense vibration or shock, or a location subject to continuous vibration. - Outdoors - Forcibly remove the product after mounting it. - Cut or damage the power cable. Use a damaged cable. - Press down on the product. - Drop the product or subject the product to intense vibration or shock. - Spray with a cleanser or other liquid. - Do not polish metal parts with a brush or polishing agent. This may damage the metal and cause corrosion. When there is abnormal situations, please cut off the power immediately, consult with electricians, and do not touch the lighting with hands. Inspection and maintenance [Inspection points] □ Do the LEDs illuminate normally? (Flickering or non-illumination?) □ No abnormalities in the installation conditions? □ No abnormal heat generation, noise, or odors? [Maintenance procedure] Gently wipe off any dirt with a soft cloth. Do not use organic volatile solvents such as thinner or benzene, and do not wash with water. 2014/05/23 LLC-PWM5A-LP2 PWM Driver 5A-LP2 Instruction Manual Wiring Maximum total wiring distance of 30 m to end driver. Input side Normal Output side - PWM -OUT +PWM +OUT I nvert Output side Input side 出力PWMモニタ ■ Wiring drawing AC100~200V Input and output of PWM signals. The signal can also be sent to the next LLC-PWM5A. *To expand the system, wire in parallel branches as shown at right. To controller or driver AC:N (White) VCTF cable 0.75sq / 2C or higher Dedicated LED power supply PWM IN PWM Dimming Driver 5A-LP2 Luci Disk Luci Disk PWM OUT Luci Disk + - + - +OUT -OUT I nvert + Normal When Disk is used, set to Normal Red Yellow - PWM Blk Blue DC / DC constant current driver Up to 5 can be connected +PWM 出力PWMモニタ PWM 入力 DC5V∼12V PWM調光ドライバー5A-LP2 (LLC-PWM5A-LP2) 電源入力 DC12~24V(5Amax) DC / DC constant current driver (LDD-700HW-BK / LDD-1000HW-BK) DC24V To next driver ■ Disk wiring example AC:L (Black) The number that can be connected in series depends on the maximum number connectable in series of the lamp fittings. Dimming type LP2 lamp fitting connections AC IN To PWM Light Controller Dedicated LED power supply PWM調光ドライバー5A-LP2 (LLC-PWM5A-LP2) AC:N (White) AC IN To dedicated LED power supply + + Input of DC 24 V power for LEDs. - AC:L (Black) PWM入力 DC5V∼12V - PWM 入力 DC5V∼12V + -OUT - +OUT + - PWM - *Use with DIP switch B on Light Controller set to master mode +PWM 電源入力 DC12~24V(5Amax) + + Normal Input and output of PWM signals. The signal can also be sent to the next LLC-PWM5A. DIP B +V I nvert Monitor that indicates the status of PWM output. Emits a green light at the same dimming level as the LED appliance. -V +V + + + - 出力PWMモニタ PWM調光ドライバー5A-LP2 (LLC-PWM5A-LP2) -V - PWM Light Controller (rear) →Up to 20 units can be connected in series VCTF cable 0.75sq / 2C or greater + Outputs the PWM signal. If the receiving side has 3 conductors (DC + -, PWM+), use - as a common conductor. Do not tie PWM signal line and power line together. Risk of malfunction. PWM signal OUT - Outputs DC 24 V To dimming type LP2 PWM signal IN 電源入力 DC12~24V(5Amax) ■ How to connect the unit White DC12V_PWM Maximum total wiring distance of 1 m between dedicated LED power supply and constant current driver. Luci Disk Luci Disk ■ Connections Maximum wiring distance of 30 m between constant current driver and end LED lamp fitting