Download Report

MODEL: BLOWFISH
OWNER’S MANUAL
Dear customer,
Congratulations on your purchase of a Fisher Boards inflatable paddleboard. We take great pride in
bringing you a quality product which will offer you years of use and enjoyment. Your new item is an
investment which deserves your care and attention. This manual has been compiled to help you to
operate and care for your product with safety and pleasure. It contains details of the product, its
equipment, and information on its operation and maintenance. Read it carefully and familiarize yourself
with the inflatable before using it in order to ensure the safe use and prevent tragic accidents.
The warnings below are advisories relative to various types of situations. Please observe them.
1
MODEL: BLOWFISH
OWNER’S MANUAL
CAUTION! Denotes an imminent hazard which will result in severe injury if you do not comply with the
instructions.
WARNING ! Reminds you of safety measures which must be observed. Denotes also unsafe practices
which could result in injury or product or property damage if you do not comply with the instructions.
CAUTION !
It is the owner’s responsibility to make sure that all users will carefully read and follow the manual
and instructions for the safe operation of this product. Knowledge and compliance with all local
and national laws is a must. Always wear a Coast Guard approved Personal Flotation Device.
Please observe carefully the information below about the capacity.
MODEL
LENGTH
INFLATED
WIDTH
INFLATED
WEIGHT
LBS
PERSONS
CAPACITY
MAX LOAD
CAPACITY
BLOWFISH
11 feet
32 inches
31 lbs
1
260 lbs
BLOWFISH EQUIPMENT:
A
A Haul Out Handle
Back Pack Duffle
Removable
Adjustable Fin
B Gear Bunge
B
C EVA Traction Pad
D Carry Handle
C
E Inflation/Deflation Valve
F Grab Handle
D
Adjustable
Paddle
F
E
Heavy Duty
Pump w/
Pressure Gauge
Repair Kit
Valve Wrench
2
MODEL: BLOWFISH
OWNER’S MANUAL
ASSEMBLY INSTRUCTIONS
CAUTION!
Do not use a sharp tool !
For the first inflation and in order to get acquainted with your new product, remove the retention strap
and unroll the board allowing it to relax and inflate indoors at room temperature where the PVC will be
soft and assembly process made easier.
Any use of an air compressor will damage your product and automatically void all warranties.
If it was stored at a temperature below 0°C / 32°F, leave it at 20°C / 68°F for 12 hours before unfolding.
Inflate it with the provided pump or any manual or powered inflator designed for inflatable boats, rafts,
pool floats, air beds, camping mattresses, and other low pressure inflatables.
Choose a smooth and clean surface to unfold your product.
BOARD INFLATION
1. Your product is equipped with a high quality high spring loaded military inflation valve at the tail of the
board. To inflate, open the valve cap by twisting it counter clockwise. Check with your thumb or
forefinger and gently push and twist the plunger pin. If the pin stays locked in the down position, you
have now opened that valve. To close it, depress and twist the plunder pin so it springs back up. Now
the valve is closed. ALL INFLATION is done in the CLOSED (UPWARD) position and DEFLATION is
done in the OPEN (DOWNWARD) position.
2. To attach the pump hose to the valve on the board simply push the fitting into the valve and turn clock
wise to lock it. Inflate until you will reach the required pressure (see point 3). After inflation disconnect
the hose from the valve and close the valve with the valve cap by twisting it clockwise until it stops.
Please note: THE VALVE WILL NOT BE COMPLETELY AIRTIGHT UNTIL THE CAP IS SECURELY IN
PLACE.
3. Max. air pressure: The correct pressure for this board is 12-14 psi. DO NOT EXCEED IT. Please
check the pressure with the supplied pressure gauge while you are inflating the board. Overpressure:
deflate until you reach the recommended pressure. Drop of pressure: inflate again slightly.
1
2
3
3
MODEL: BLOWFISH
OWNER’S MANUAL
INSTALLING CENTER FIN
1
2
Make sure the center fin box is clean and free of debris before
installing the fins.
3
Using the screw, slide the metal plate all the way forward in
the fin box.
4
Holding the fin at an angle, insert the metal pin into the fin box
opening.
5
Keeping the fin at an angle, slide the fin into position.
6
Holding the fin firmly, push the fin flush with the fin box.
7
Using the screwdriver, line up the hole in the metal plate with
the hole in the fin tab.
8
Insert the screw into the fin tab.
Using the screwdriver, tighten the screw into the underlying
metal plate.
4
MODEL: BLOWFISH
OWNER’S MANUAL
WARNING ! If you leave your product exposed to the hot sun check the pressure and deflate it slightly,
otherwise the material could become overstretched. Be conscious of the temperature(s) you are
operating in. The ambient temperature affects the tube’s internal pressure: a variation of 1°C causes a
variation of the pressure in the tube of .06 lbs.
OPERATING INSTRUCTIONS
WARNING ! BEWARE OF OFFSHORE WINDS AND CURRENTS!
• Get informed on local regulations and hazards related to this sport and other water activities.
• Learn about your paddling area. Ask locals about tides and currents.
• Before using the product each time, please check it carefully.
• Be careful that you do not over estimate your strength, your endurance or your skill.
• Be careful never to under estimate the forces of nature and inherent hazards.
• Do not exceed the authorized number of persons or weight.
• Avoid all contact with sharp objects or aggressive liquids (such as acid & solvents).
• This product is delivered with a poly bag. keep it away from children and dispose of it properly.
Danger of suffocation!
PROPER PADDLING TECHNIQUE
Blade
Facing
Forward
Blade
Facing
Forward
CORRECT
INCORRECT
5
MODEL: BLOWFISH
OWNER’S MANUAL
CARE & MAINTENANCE: CLEANING-DEFLATING-STORAGE-REPAIR
1. Always rinse your board thoroughly with fresh water before storing (garden hose with a high pressure
stream sprayer like washing your car works great). A mild soapy solution works great as well as along
with the scrubbing part of a non-scratch kitchen sponge to remove any stubborn marks. Do not use
strong chemical detergents, cleaners, bleaches, solvents or any type of silicone-based products. Make
sure the product is completely dry before putting it away. Inspect the board completely.
2. Unscrew and remove the center fin keep the screw and plate screwed onto the fin so you do not lose
them. Store fin in the front pocket of the carry bag.
3. To deflate, unscrew the valve cap and open the valve to the down position until it locks. Give it five
minutes or so to completely exhaust and relax itself – makes rolling easier too.
4. Rolling up – Keep the D-ring retention strap handy by the tail so you can grab it when you are finished
rolling. Starting at the nose roll the board up tightly – it is a bit hard at first but gets easier as the roll
gets larger and you use the weight of the roll to flatten what is ahead of you. When you have rolled the
board up wrap the retention strap around the roll and feed the strap through the D-ring and cinch it up
tight.
5. Getting it in the duffle bag. The easiest way (particularly if you are by yourself) is to stand the roll on
one end and pull the bag onto it and then turn it right-side up. If you have rolled it up tightly enough you
will have plenty of room on the sides in the bag to store the paddle, pump & repair kit.
6. When storing your inflatable, keep it in a clean and dry place that is not affected from major variations
in temperature and other damaging factors. You may store it deflated and rolled up in the bag or lightly
inflated (make sure you do not subject it to deformations like hanging it on a fence or rail). Store it away
from rodents and any other chewing animals – they like rubber!
VALVE CAUTION & CARE
The inflation/deflation valve is maintenance free however use caution during inflation/deflation or any
time the valve cover is off not to get sand, dirt, debris or water in the valve! Also a valve wrench is
included in the repair kit. The valve comes in two parts that screw together and “bite down” on the inner
and outer surfaces of the PVC deck. Should this start to loosen up the valve wrench is included to
re-tighten. Turning it clockwise will pinch the upper and lower flanges and keep the seal airtight.
INFLATION/DEFLATION VALVE
CAUTION!
NO DIRT, SAND OR
DEBRIS OR WATER
CAN ENTER
6
MODEL: BLOWFISH
OWNER’S MANUAL
HOW TO REPAIR SMALL PUNCTURES
You can repair small punctures with the included repair kit. Please note that in order for the repair to be
successful, the humidity level should be less than 60%, temperature between 65° F/77° F or
18°C/25°C. Avoid carrying out repairs in the rain or in direct sunlight.
1. Draw the shape of the patch exactly where it will be applied, cut a round patch at least 1” larger on
all sides than the cut/damaged area.
2. Clean the damaged area and the corresponding side of the patch with a grease remover like rubbing
alcohol and allow for it to dry for 5 minutes. Remove/trim any pieces that would not allow the patch to
apply flat and smooth. Light roughing the area to be repaired with fine 600 or finer grit wet/dry
sandpaper or the green scouring pads will help adhesion.
3. Apply 3 thin layers of glue on both the patch and the damaged area, allow for it to dry for 5 minutes
between layers until the glue feels tacky.
4. When the third layer of glue is dry, apply the patch without pressing and adjust the positioning if
required, press the air bubbles which may have formed under the patch by smoothing the patch with a
round object such as a spoon, do this procedure by starting in the center of the patch towards the
outside, clean the excess glue with a solvent. LET DRY AT LEAST 12 HOURS BEFORE INFLATING
AGAIN. ONCE INFLATED CHECK THE REPAIR WITH SOAPY SOLUTION AND LOOK FOR
BUBBLES. If you see bubbles the repair is not airtight. For larger repairs consult your local boating or
marine center who handles repairs of these types for rafts, rubber boats and such.
ATTENTION!
• Perform all of your repairs in a well-ventilated area
• Avoid inhaling glue vapors or swallowing.
• Avoid contact with the skin or the eyes.
• Keep all repair materials (glue, solvents, etc.) away from children’s reach
7
MODEL: BLOWFISH
OWNER’S MANUAL
RELEASE OF LIABILITY, CLAIM WAIVER AND ASSUMPTION OF RISK AGREEMENT
RELEASE AND WAIVER OF CLAIMS AGREEMENT
In consideration of your use of this product, you hereby agree to the following, to the fullest extent
permitted by law:
1. To waive any and all claims that you have or may in the future have against Surf Ventures Unlimited.
LLC, or any of its agents, resulting from use of this product and any of its components.
2. To release Surf Ventures Unlimited, LLC, or any of its agents from any and all liability from any loss,
damage, injury or expense that you or any users of this product may suffer, or that your next of kin may
suffer, as a result of the use of this product, due to any cause whatsoever, including negligence or
breach of contract on the part of Surf Ventures Unlimited, LLC, or any of its agents, in the design or
manufacture of this product.
Arbitration
In further consideration of the sale to you of this product and any of its components, you hereby agree
to submit to binding arbitration any and all claims, which you believe you may have against Surf Ventures
Unlimited, LLC, or any of its agents, arising from the use of any of the Surf Ventures Unlimited, LLC
equipment. The arbitration shall be pursuant to the rules of the American Arbitration Association.
Arbitration shall be commenced within one (1) year from the date on which any alleged claim first arose.
Further, the arbitration shall be held in San Diego, CA unless otherwise mutually agreed to by all parties.
The submission to the American Arbitration Association shall be limited and the arbitration award may
be enforced by any court of competent jurisdiction.
Binding Effect of Agreement
In the event of your death or incapacity, this Agreement shall be effective and binding upon your heirs,
next of kin, executors, administrators, assigns and representatives.
Entire Agreement
In entering into this Agreement, you are not relying upon any oral or written representations other than
what is set forth in this agreement and User’s Guide.
Assumption of Risk
By purchasing, using and assembling this product, you are agreeing to:
1. Be bound to the terms set forth; and
2. Require anyone using this product to be bound by such terms. If you are unwilling to be bound by
these terms, return this product before use for a full refund.
Use of this product and any of its components involves certain inherent risks, dangers and hazards,
which can result in serious personal injury and death. In using this product you freely agree to assume
and accept any and all known and unknown risks of injury while using this equipment. The risks inherent
in the sport can be greatly reduced by abiding to the Warning and Safety Precautions listed in this User
Guide and using common sense.
8
MODEL: BLOWFISH
OWNER’S MANUAL
WARNING AND SAFETY PRECAUTIONS
General Warnings:
1. Stand-up Paddling is a dangerous sport. Use of this product exposes the user to unexpected risks,
dangers and hazards.
2. Always use extreme caution when using this product. Never act in a careless manner when using this
product. Misuse of this product may result in serious injury or death.
3. Only use this product if you are in good physical health, and know how to swim.
4. You are responsible for your own safety and the safety of others around you when using this product.
5. If you are under the age of 18, you must have a legal guardian read these warnings and safety
precautions. Do not use this product without adult supervision.
6. Do not use this product if you are under the influence of alcohol, drugs or medications.
Important Safety Rules:
1. Before using this product, the user should take lessons from a certified school. This product should
not be used by anyone who is not experienced with stand-up paddling.
2. Always wear a Coast Guard Approved personal flotation device when using this product.
This product is not a personal flotation device.
3. Never use this product without a proper paddleboard leash in the ocean or any body of moving water.
A loose stand-up board in the water is extremely dangerous to you, and everyone around you. Failure to
use a paddleboard leash may result in serious injury or death.
4. Examine your paddleboard leash after each use, and replace it if you see any sign of wear.
5. Always wear a helmet and booties when using this product in hazardous conditions at your own risk.
6. Always paddle with an experienced partner when using this product.
Weather Condition & Location Warnings:
1. Always observe Coast Guard rules and regulations when using this product.
2. Never use this product in offshore wind conditions.
3. Never use this product in more than 10 knots of wind. Using this product in windy conditions may
result in serious injury or death.
4. Use caution when carrying this product. Carrying the board in windy conditions may result in serious
injury to yourself and others around you.
5. Never use this product in thunderstorms and lightning conditions.
6. Never use this product in conditions that are beyond your ability (such as, but not limited to, high surf,
riptides, currents, or river rapids).
7. Never use this product near other boat traffic, or watercrafts.
8. Never use this product near crowded beaches or waters
9
MODEL: BLOWFISH
OWNER’S MANUAL
WARRANTY
Fisher Boards warrants (legal warranty) to the original purchaser only, and from date of purchase, when
any product is used for normal recreational purposes, that the product is free from defects (weldings).
The warranty does not cover any puncture, cut or abrasion sustained in normal use or damage from
unreasonable uses or improper storage. If any product is found to be defective, the owner may return it
to the store it was purchased from with the original sales receipt.
After inspection of any product found defective, Fisher Boards shall either repair or replace the
defective part or item as deemed necessary by Fisher Boards. Fisher Boards shall not be held liable for
incidental and consequential damages. There are no warranties which extend beyond the description of
the face hereof. This warranty is inclusive in lieu of all other warranties.
This warranty gives you specific legal rights and you may also have other rights, which may vary, from
country to country.
The main limitations to the application of the warranty are the following:
• The product must not be modified or retro-fitted or used in any activities outside normal recreational
use (such as races, rentals, professional usage).
• Use in excess of the manufacturers recommended maximum load capacity.
• Pressure recommendations, inflation/deflation and handling procedures must be strictly observed.
• The maintenance and the storage procedures must not be neglected.
• This warranty does not cover parts and accessories not supplied or recommended by the manufacturer
or defects resulting from the installation of such equipment on their products.
NOTICE : all repairs covered by warranty must be performed by Fisher Boards.
WARNING!
Your product is designed in accordance with the standards for a specific use. Any modifications,
transformations or use of the product other than indicated by the manufacturer could result in serious
risks for the user and will void the warranty.
10