1. science
2. mathematics
3. geometry

Installation and
Operation Manual
SPECIALITY OVENS
Stone Hearth Oven
Radiant Flame, Gas-Fired Models
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
TRAILERED MODELS
MS-5
WS-MS-5-RFG-(IR)-LP
BISTRO 4355
WS-BL-4355-RFG-LP
tf.800.988.8103
t.360.650.1111
f.360.650.1166
woodstone-corp.com
Revised January 2014
Doc no: M0055.00
TABLE OF CONTENTS
Trailered Ovens
Installation and Operation Manual
TABLE OF CONTENTS
TRAILERED OVENS���������������������������������������������3
CAUTIONS AND WARNINGS �������������������������������4
MS-5 SPECIFICATIONS���������������������������������������6
BL-4355 SPECIFICATIONS���������������������������������7
INSTALLATION CLEARANCES �����������������������������8
VENTING�����������������������������������������������������������9
PROPANE SYSTEM�������������������������������������������10
GAS SPECIFICATIONS���������������������������������������11
ELECTRICAL SPECIFICATIONS���������������������������12
MS-5 OPERATION
MS-5 CONTROLLER�����������������������������������13
MS-5 INITIAL START-UP �����������������������������14
MS-5 DAILY OPERATION�����������������������������15
BL-4355 OPERATION
BL-4355 CONTROLLER�������������������������������16
BL-4355 INITIAL START-UP�������������������������17
BL-4355 DAILY OPERATION�������������������������18
FLAME HEIGHT CONTROL �������������������������������19
CLEANING�������������������������������������������������������20
PERIODIC THERMAL CLEANING �����������������������21
TROUBLESHOOTING�����������������������������������������22
MS-5 OPERATIONAL SEQUENCE�����������������������23
BL-4355 OPERATIONAL SEQUENCE�����������������25
MS-5 ELECTRICAL DIAGRAM���������������������������26
BL-4355 ELECTRICAL DIAGRAM�����������������������28
LIMITED WARRANTY ���������������������������������������29
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
2
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
TRAILERED OVENS
Trailered Ovens
Installation and Operation Manual
INSTALLATION AND OPERATION MANUAL FOR
THE WOOD STONE TRAILER OVENS
STONE HEARTH COOKING EQUIPMENT
TRAILER MOUNTED GAS-FIRED OVEN
WS-MS-5-RFG-(IR)-TR-LP MODELS (INCLUDES NAPLES MODELS)
WS-BL-4355-RFG-TR-LP
ADDITIONAL COPIES AVAILABLE UPON REQUEST
WS-MS-5-RFG-IR-TR-LP
WS-BL-4355-RFG-TR-LP
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
3
CAUTIONS AND WARNINGS
Trailered Ovens
Installation and Operation Manual
INSTALLATION AND OPERATION MANUAL FOR WOOD STONE TRAILERED OVENS
PROPANE (LP) FUELED STONE HEARTH OVEN
RETAIN THIS MANUAL FOR FUTURE REFERENCE
Additional copies of this manual and prompt responses to service/maintenance
questions are available from Wood Stone @ 1-800-988-8103.
READ ALL INSTRUCTIONS BEFORE INSTALLING AND USING THIS APPLIANCE
Please read this entire manual before you install the oven. Failure to follow instructions may result in
property damage, bodily injury or even death. Contact your local building or fire officials about restrictions
and installation inspection in your area.
IMPORTANT: Consult your local gas supplier for a statement outlining a procedure to be followed in the
event you smell gas. Post the statement in a prominent location.
FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this
or any other appliance.
POUR VOTRE SÉCURITÉ: Ne pas entreposer ni utiliser d’essence ou d’autres vapeurs de liquides
inflammables ou des liquides dans les environs de ce ou de tout autre appareil.
IMPORTANT: It is recommended that this oven be installed, maintained and serviced by authorized
professionals. When his oven is not properly installed, a fire may result. To reduce the risk of fire, follow
the installation instructions.
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
4
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
CAUTIONS AND WARNINGS
Trailered Ovens
Installation and Operation Manual
A MAJOR CAUSE OF OVEN RELATED FIRES IS A
FAILURE TO MAINTAIN REQUIRED CLEARANCES
TO COMBUSTIBLE MATERIAL. IT IS OF UTMOST
IMPORTANCE THAT THIS OVEN BE INSTALLED ONLY
IN ACCORDANCE WITH THESE INSTRUCTIONS.
DISCONNECT POWER TO THE OVEN BEFORE SERVICING OR CLEANING.
NO ATTEMPT SHOULD BE MADE TO OPERATE THIS APPLIANCE DURING A POWER FAILURE
WARNING: Improper installation, adjustment, alteration, service or maintenance can result in property
damage, injury or death. Read the installation, operation and maintenance instructions thoroughly before
installing or servicing this equipment.
AVERTISSEMENT: L’installation, le réglage, la modification, la réparation ou l’entretien incorrect de cet
appareil peut causer des dommages matériels, de blessures ou la mort. Lire attentivement les instructions
d’installation, de fonctionement et d’entretien avant de procéder à son installation ou entretien.
SAVE THE INSTRUCTIONS
Wood Stone’s gas-fired ovens have been tested and approved by Intertek Testing Services,
and are ETL Listed to ANSI Z83.11b - 2009, CSA 1.8b-2009
and to NSF/ANSI Standard 4 - 2009.
ANSI Z83.11b-2009 ANSI/NSF STD 4
CSA 1.8b-2009
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
5
MS-5 SPECIFICATIONS
Trailered Ovens
Installation and Operation Manual
Plan view
76 3/4"
1950mm
17"
430mm
1
16"
410mm
16"
16"
410mm 410mm
64 1/4"
1630mm
2
1
1
Air intake:
Do not cover
Must be left
removable for service
Shipping weight: 5,000 lbs.
76 3/4" 76 3/4"
1950mm 1950mm
17"
17"
430mm 430mm
2
2
64 1/4" 64 1/4"
1630mm 1630mm
* Dimensions shown are as
shipped. Due to loading, tire
pressure and terrain, these
dimensions may vary.
108"
2740mm
147"
3730mm
108"
108"
2740mm 2740mm
147"
147"
3730mm 3730mm
Side view
Front
22 3/4"
580mm
64 1/2"
1640mm
29 3/4"
view
750mm
64
1/2"
1640mm
29 3/4"
750mm
64 1/2"
1640mm
29 3/4"
750mm
22 3/4" 22 3/4"
580mm 580mm
81 1/4" *
2060mm
52 1/2" *
1330mm
61 1/2" 61 1/2"
1560mm 21560mm
2
104" * 104" *
2640mm 2640mm
35 1/4" *
900mm52 1/2" * 52 1/2" *
1330mm 1330mm
1
1
9 3/4"
250mm
104" *
81 1/4"2640mm
* 81 1/4" *
2060mm 2060mm
61 1/2"
1560mm
2
35*1/4" * 35 1/4" *
19 3/4"
900mm 900mm
500mm
1
16"
410mm
AIR
INTAKE
AIR
AIR
INTAKE INTAKE
9 3/4"
9 3/4"
250mm 250mm
11 1/2"
290mm
11 1/2" 11 1/2"
290mm 290mm
83 1/2"
2120mm
19 3/4" * 19 3/4" *
500mm 500mm
83 1/2" 83 1/2"
2120mm 2120mm
16"
16"
410mm 410mm
UTILITIES SPECIFICATIONS
REV:
Electrical
Venting
Gas
PART #: WS-MS-5-RFG-TR
SHEET: 1 of 1
Self-contained Propane (LP)
(1) At trailer: PowerDATE:
cord 12
VDC
Self-contained.
For
outdoor
use
only
in
well
ventilated
areas.
5/1/2013
DWN BY: bena
REV: REV:
RFG: 94,000 BTU/hr
7-pin receptaclePART #:PART
WS-MS-5-RFG-TR
1 of 1 1 of 1
No additional venting required.
#: WS-MS-5-RFG-TR
SHEET:SHEET:
ingham, WA 360/650-1111
www.woodstone-corp.com
RFG-IR: 159,000 BTU/hr
(2) At oven: 120 VAC,
1.1
A,
NEMA
DATE: DATE:
5/1/2013
5/1/2013
DWNbena
BY: bena
DWN Oven
BY:
5' Trailered
L5-15 plug
ARE www.woodstone-corp.com
IN INCHES
Bellingham,
WA 360/650-1111
ingham,
WA DIMENSIONS
360/650-1111
www.woodstone-corp.com
TOLERANCES: LINEAR ±1/2 [±10mm], ANGULAR ±2°
UNLESS NOTED OTHERWISE
DIMENSIONS
IN INCHES
DIMENSIONS
ARE INARE
INCHES
AN
ONGOING
PROGRAM
OF [±10mm],
PRODUCT
IMPROVEMENT
TOLERANCES:
LINEAR
±1/2 [±10mm],
ANGULAR
TOLERANCES:
LINEAR
±1/2
ANGULAR
±2° ±2°
MAY REQUIRE
USNOTED
TO CHANGE
SPECIFICATIONS
UNLESS
NOTED
OTHERWISE
UNLESS
OTHERWISE
LEGEND:
WITHOUT
NOTICE.
AN ONGOING
PROGRAM
OF PRODUCT
IMPROVEMENT
AN ONGOING
PROGRAM
OF PRODUCT
IMPROVEMENT
1
MAY REQUIRE
TO IN
CHANGE
SPECIFICATIONS
MAY REQUIRE
US TOUS
CHANGE
SPECIFICATIONS
E INFORMATION
CONTAINED
THIS
DRAWING
IS THE
LEGEND:
An ongoing
of NOTICE.
product
improvement
may require us to change LEGEND:
SOLE PROPERTY
OFprogram
WOOD
STONE
CORPORATION
WITHOUT
NOTICE.
WITHOUT
specifications without notice. Trailered Ovens, Revised January 2014.
NY REPRODUCTION
OR USE IN PART OR AS A WHOLE
1
THE INFORMATION
CONTAINED
INDRAWING
THIS DRAWING
E INFORMATION
CONTAINED
IN THIS
IS THEIS THE 1
THOUT THE WRITTEN PERMISSION OF WOOD STONE IS
2
PROPERTY
OF WOOD
STONE
CORPORATION
SOLE SOLE
PROPERTY
OF WOOD
STONE
CORPORATION
PROHIBITED
ANY
ORINUSE
IN PART
AS A WHOLE
NY REPRODUCTION
OR USE
PART
OR ASOR
A WHOLE
6 REPRODUCTION
WITHOUT
THE WRITTEN
PERMISSION
OF WOOD
STONE
IS 2
HOUT
THE WRITTEN
PERMISSION
OF WOOD
STONE
IS
2
dstone.net\dfs\CAD\0 Pn\WS Top Level\WS-MS-5-TR_General_Arrangement-1.dft
PROHIBITED
PROHIBITED
1
11
5' Trailered
Oven
5' Trailered
Oven
General
Arrangement
wood stone
corporation
tf.800.988.8103
General
Arrangement
General
Arrangement
t.360.650.1111
*f.360.650.1166
Dimensions Shown Are "As Shipped."
Power
12 V DC 7-Pinrd.
1801Cord
w. bakerview
Receptacle
At Trailer
bellingham,
wa 98226 usa
Due To Loading, Tire Pressure, and
Power
V DC 7-Pin
Power Cord
12Cord
V DC12
7-Pin
[email protected]
or visit woodstone-corp.com
Terrain, These Dimensions May Vary.
Power
Cord
Receptacle
Receptacle
AtReceptacle
TrailerAt Trailer
* Dimensions
Shown
"As Shipped."
* Dimensions
Shown Are
"As Are
Shipped."
120 VAC, 2 A NEMA L5-15
To Loading,
Tire Pressure,
Due To Due
Loading,
Tire Pressure,
and and
Plug At Oven
These Dimensions
May Vary.
Terrain, Terrain,
These Dimensions
May Vary.
Power
Cord Receptacle
Power Cord
Receptacle
120
2 AL5-15
NEMA L5-15
120 VAC,
2 AVAC,
NEMA
Plug At Oven
Plug At Oven
VENTING
Trailered Ovens
Installation and Operation Manual
This oven is for outdoor use only. It is equipped with an oven mounted collapsible flue which must be raised before operating the
oven. To raise the flue, twist clockwise slightly to unlock it, then raise it up and twist clockwise again to lock the flue into position.
Before transporting the oven, lower the flue and lock it in place. Raise slightly and twist counterclockwise to release, lower the flue,
then twist counterclockwise to lock into place.
WARNING: FLUE WILL BE HOT AFTER USE. Make sure the flue has had sufficient time to cool before attempting to lower it. If
the flue is still hot, wear gloves to prevent the chance of burns.
Inspect flue regularly and remove any residues before they accumulate.
If cleaning is necessary, the flue can be accessed through the oven doorway. Allow the oven to cool. Place cardboard, sheet pans
or towels in the oven doorway to prevent cleaning solution from contacting the oven floor (hearth). Use a mild soap solution mixed
with hot water and a long handled brush to clean the flue pipe. Wipe up any cleaning solution that may have contacted the oven
floor.
Flue extended and
locked.
Flue collasped.
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
Flue collapsed and
locked.
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
7
BL-4355 SPECIFICATIONS
Trailered Ovens
Installation and Operation Manual
Plan view
1
31"
790mm
62 1/2"
1580mm
31"
31"
790mm 2790mm
62 1/2" 62 1/2"
1580mm1580mm
10 3/4"
270mm
10 3/4" 10 3/4"
270mm
64270mm
1/4"
1630mm
9"
230mm
1
1
2
147"
3730mm
2
64 1/4" 64 1/4"
1630mm1630mm
108"
2740mm
Air intake:
Do not cover
Must be left
removable for service
Shipping weight: 4,000 lbs.
* Dimensions shown are as
shipped. Due to loading, tire
pressure and terrain, these
dimensions may vary.
9"
9"
230mm 230mm
Side view
42 1/2"
1080mm
24 1/2"
620mm
Front view
108" 108"
2740mm2740mm
147" 147"
3730mm3730mm
18 1/4"
460mm
42 1/2" 42 1/2"
1080mm1080mm
24 1/2" 24 1/2"
620mm 620mm
74" *
1880mm
54 1/4"
1380mm
92 1/4" *
18 1/4"
18 1/4"
2340mm
460mm 460mm
51" *
1300mm
2
AIR INTAKE
41" *
1040mm
74" * 74" *
1880mm1880mm
1
2
1
9 3/4" 9 3/4"
250mm 250mm
19 3/4" *
500mm
54 1/4" 54 1/4"
1380mm1380mm
2
8"
200mm
9 3/4"
250mm
92 1/4" * 92 1/4" *
2340mm2340mm
51" * 51" *
1300mm1300mm
41" * 41" *
1040mm1040mm
83 1/2"
2120mm
AIR INTAKE
AIR INTAKE
1
19 3/4" * 19 3/4" *
500mm 500mm
83 1/2" 83 1/2"
2120mm2120mm
8"
8"
200mm 200mm
UTILITIES SPECIFICATIONS
REV:
SHEET: 1 of 1
Electrical PART #: WS-BL-4355-RFG-TRVenting
Gas
DATE:cord
5/1/2013
Self-contained Propane (LP)
DWN
BY: bena
(1) At trailer: Power
12 VDC
Self-contained. For
outdoor
use only in well ventilated areas.
lingham, WA 360/650-1111
www.woodstone-corp.com 7-pin receptacle
68,000 BTU/hr
No additional venting required.
(2) At oven: 120 VAC, 2 A, NEMA
WS-BL-4355-RFG-TR
DIMENSIONS ARE IN INCHES
TOLERANCES: LINEAR ±1/2 [±10mm], ANGULARL5-15
±2° plug
REV: REV:
1
UNLESS NOTED OTHERWISE
PART PART
#: WS-BL-4355-RFG-TR
#: WS-BL-4355-RFG-TR
General
DATE:DATE:
5/1/2013
5/1/2013
AN ONGOING PROGRAM OF PRODUCT IMPROVEMENT
lingham,
WA 360/650-1111
MAY
REQUIRE
US TOwww.woodstone-corp.com
CHANGE
SPECIFICATIONS
Bellingham,
WA 360/650-1111
www.woodstone-corp.com
LEGEND:
WITHOUT NOTICE.
DIMENSIONS
ARE
IN
INCHES
DIMENSIONS
ARE
IN
INCHES
1
E INFORMATION CONTAINED IN THIS DRAWING IS THE
TOLERANCES:
LINEAR
±1/2 [±10mm],
ANGULAR
±2° ±2°
±1/2
[±10mm],
ANGULAR
SOLETOLERANCES:
PROPERTY
OFLINEAR
WOOD
STONE
CORPORATION
UNLESS
NOTED
OTHERWISE
UNLESS
NOTED
OTHERWISE
NY REPRODUCTION
OR USE
IN PART
OR AS A WHOLE
1 of 11 of 1
SHEET:
SHEET:
Arrangement
DWN BY:
DWNbena
BY: bena
11
* Dimensions
Shown Are "As Shipped."
tf.800.988.8103
WS-BL-4355-RFG-TR
WS-BL-4355-RFG-TR
wood
Power Cord
12 V stone
DC 7-Pincorporation
Receptacle
At Trailer
1801
w. bakerview rd.
Due To Loading, Tire Pressure, and
t.360.650.1111
Terrain, These Dimensions May Vary.
General
Arrangement
General
Arrangement
bellingham,
wa 98226
usa
f.360.650.1166
Power Cord Receptacle
An ongoing program of product improvement may require us to change
AN ONGOING
PROGRAM
OF PRODUCT
THOUT
WRITTEN
PERMISSION
OF IMPROVEMENT
WOOD
STONE IS
ANTHE
ONGOING
PROGRAM
OF PRODUCT
IMPROVEMENT
120 VAC,[email protected]
2 A NEMA L5-15
specifications without notice. Trailered Ovens, Revised January 2014. 2
or visit woodstone-corp.com
MAY REQUIRE
USPROHIBITED
TO
CHANGE
SPECIFICATIONS
MAY REQUIRE
US
TO CHANGE
SPECIFICATIONS
Plug At Oven
LEGEND:
LEGEND:
WITHOUT
NOTICE.
WITHOUT
NOTICE.
* Dimensions
ShownShown
Are "AsAre
Shipped."
* Dimensions
"As Shipped."
Power Power
Cord 12Cord
V DC
127-Pin
V DC 7-Pin
dstone.net\dfs\CAD\0 Pn\WS Top Level\WS-BL-4355-TR_General_Arrangement-1.dft
HE
INFORMATION
CONTAINED
IN THIS
DRAWING
IS THE
Due
To
Loading,
Tire
Pressure,
and and
1
THE8INFORMATION
CONTAINED
IN THIS
DRAWING
IS THE 1
Due
To
Loading,
Tire
Pressure,
Receptacle
At Trailer
Receptacle
At Trailer
Terrain,Terrain,
These Dimensions
May Vary.
SOLESOLE
PROPERTY
OF WOOD
STONE
CORPORATION
These Dimensions
May Vary.
PROPERTY
OF WOOD
STONE
CORPORATION
NY REPRODUCTION
OR USE
PART
OR AS
A AS
WHOLE
ANY REPRODUCTION
OR IN
USE
IN PART
OR
A WHOLE
INSTALLATION CLEARANCES
Trailered Ovens
Installation and Operation Manual
IF THIS OVEN IS NOT PROPERLY INSTALLED A FIRE MAY RESULT. TO REDUCE THE RISK OF FIRE, FOLLOW THESE INSTALLATION
INSTRUCTIONS. A MAJOR CAUSE OF OVEN RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES)
TO COMBUSTIBLE MATERIALS. IT IS OF UTMOST IMPORTANCE THAT THIS OVEN BE INSTALLED ONLY IN ACCORDANCE
WITH THESE INSTRUCTIONS.
!
WARNING: Installation and servicing of this product could expose you to glasswool/ceramic fibers as well
as calcium silicate dust. ALWAYS WEAR RESPIRATORY AND EYE PROTECTION WHEN INSTALLING OR
SERVICING THIS APPLIANCE. Please read this entire manual before you install the oven. Failure to follow
instructions may result in property damage, bodily injury or even death. Contact your local building or fire
officials about restrictions and installation inspection in your area.
CLEARANCES
The Wood Stone gas-fired oven must have a minimum 1" clearance to combustibles from all sides, 14" clearance to
combustibles from the top and O" clearance to non-combustible materials.
WARNING: Do not pack required air spaces with insulation or other materials.
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
9
PROPANE SYSTEM
Trailered Ovens
Installation and Operation Manual
Gas-fired Wood Stone Trailered Ovens come equipped with a self-contained LP gas system onboard the trailer. For safe operation
of the LP gas system follow the guidelines below.
1. The oven comes equipped with four 30 lbs. capacity cylinders (tanks), grouped as 2 banks of cylinders. Each bank has a tank
change over valve, and the 2 banks are intended to be run at the same time to help minimize icing of the cylinders. If replacing a
cylinder, it must be constructed and marked in accordance with the specifications for propane cylinders of the U.S. Department
of Transportation (DOT) or CAN/CSA B339.
2. This oven is intended only for outdoor use, or in a well ventilated space. The oven is not intended for use in a building, garage
or any other enclosed area.
3. To remove a cylinder, make sure any open flames nearby are extinguished. Turn off the valve on the cylinder. Unscrew the hose
from the cylinder. Loosen the clamp that secures the cylinders to the trailer and remove the cylinder. Complete these steps in
reverse to install the new cylinder.
4. All gas connections should be inspected and leak checked at least yearly. To leak check, first extinguish all open flames close
by. Before turning the oven gas supply on, visually inspect all hoses, connections and pipe joints for signs of damage. Check
tightness of all connections. Check all piping beneath the oven as well. Then turn on the gas supply at the cylinder(s). Daub an
approved leak check solution or mild soap solution on to all gas connections and piping joints to check for leaks. Once the leak
check has been completed, make sure to wipe off the leak check/soap solution so that no residue is left on the hoses and piping.
5. Cylinders should be secured in the holders provided on the trailer when transporting the unit. Storing or transporting cylinders
in compartments or other locations not intended for cylinder storage could lead to an explosion, fire or personal injury.
6. Do not place propane cylinders in a high heat area such as a closed car, trunk or direct sunlight.
7. Turn off the gas supply at the cylinders when the oven is not in use, and when transporting the oven. If storing the oven indoors,
the propane cylinders must be disconnected and removed from the appliance. Cylinders must be stored outdoors, not in a
building, garage or any other enclosed area, in a well ventilated area out of reach of children. The dust cap must be installed on
the tank valve outlet when the tank is disconnected from the appliance.
8. Visually inspect hoses and regulators for damage before each use. If it is evident the hose is cut or showing excessive abrasion
or wear, it must be replaced prior to the oven being put into operation. If any components are damaged, they must be replaced
before using the appliance. Use only the regulator, hose and hose assemblies supplied by Wood Stone. If a regulator or hose
needs to be replaced, replace only with a part of equal size and ratings. Contact Wood Stone.
9. The transportation and storage of gas cylinders must be in accordance with ANSI/NFPA 58, Storage and Handling of Liquid and
Petroleum Gases, or CSA B149.1, the Natural Gas and Propane Installation Code.
10.Do not operate this appliance if the outdoor temperature is below –40 °F, or –40 °C. When transporting or using the oven in
freezing conditions, keep the propane regulator vents clear of ice, snow or slush.
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
10
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
GAS SPECIFICATIONS
Trailered Ovens
Installation and Operation Manual
SV-1 is the gas control valve that operates the infrared (IR) underfloor burner (only on MS-5-RFG-IR model). It is located beneath
the oven at the front of the IR burner.
SV-2 is the gas control valve that operates the interior radiant burner. On the MS-5 oven, the valve is located beneath the oven
at the rear, towards the side where the radiant burner is located. On the Bistro 4355 oven, the valve is located on the back of the
control box, beneath the oven.
The manifold pressure test port for the radiant burner is a 1/8" NPT plugged tapping located at the base of the T-junction between
the SV-2 and the radiant/interior burner.
The burner manifold pressure has been adjusted and tested at the factory. A variety of factors can influence this pressure, so be
sure to test the burner manifold pressure and adjust the valve as necessary to achieve the specified pressure. NOTE: The gas valve
is shipped in the ON position.
This oven requires no modifications or adjustments for use at high altitudes.
Factory specified individual burner manifold pressures and BTU/hr rates for RFG-IR models equipped to burn Propane (LP).
Model
WS-MS-5-RFG-TR-LP
WS-MS-5-RFG-IR-TR-LP
SV-1
SV-2
n/a
9"
8"
8"
Model
WS-MS-5-RFG-(NAP)-TR-LP
WS-MS-5-RFG-IR-(NAP)-TR-LP
BTU/hr Input Rate
94,000
159,000
Factory specified individual burner manifold pressures and BTU/hr rates for RFG models equipped to burn Propane (LP).
Model
WS-BL-4355-TR-LP
SV-1
SV-2
N/A
9"
Model
WS-BL-4355-TR-LP
BTU/hr Input Rate
68,000
Wood Stone recommends that inspection and maintenance of the burners and gas piping connections of this appliance be performed
at regularly scheduled intervals and only by professional gas appliance service agencies.
GAS CODE LIMITATIONS
The installation of this appliance must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code,
ANSI Z223.1 or the Natural Gas installation Code CAN/CGA-B149.1 as applicable.
The appliance and its individual shutoff valve (supplied by others) must be disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in excess of 1/2 psi (3.45 kPa).
The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve (supplied by others)
during any pressure testing of the gas supply piping system at test pressure, equal to or less than 1/2 psi (3.45 kPa).
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
11
ELECTRICAL SPECIFICATIONS
Trailered Ovens
Installation and Operation Manual
OVEN ELECTRICAL RATINGS
WS-MS-5-RFG-(IR)-TR, 2 A
WS-BL-4355-TR, 2 A
ELECTRICAL CODE LIMITATIONS
Electrical grounding: This appliance must be electrically grounded in accordance with local codes, or in the absence of local
codes, with the National Electrical code, ANSI/NFPA 70 or the Canadian Electrical Code, CSA C22.1, as applicable.
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
12
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
MS-5 CONTROLLER
Trailered Ovens
Installation and Operation Manual
CONTROLLER FUNCTIONS
MS-5-RFG MODEL
Temperature units
Press and hold to
switch between
Fahrenheit and Celsius.
Hearth Temperature
The floor (hearth) temperature
will be displayed when the
oven is turned on. Sensor
is embedded 1" below the
hearth surface. Display
will read “LO” when the
temperature is below 100 °F.
ON/OFF button
Press to turn
oven on and off.
MS-5-RFG-IR
Power indicator light
Indicates the oven is
turned ON.
Dome Flame
indicator light
Indicates the pilot
for the radiant
flame has lit.
Hearth Heat indicator light
Indicates that the pilot for the infrared
underfloor burner is lit. This light will go off
whenever the hearth temperature is above
the Hearth Set Point.
POWER DOMEHEARTH
FLAMEHEAT
Hearth Temperature display
Displays temperature of
oven floor (hearth). Sensor
is embedded 1" below the
hearth surface.
HEARTH
TEMPERATURE
Hearth Set Point display
Indicates set point
temperature of
underfloor IR burner
On/Off button
Press to turn oven on/off
HEARTH SET POINT
Push ON/OFF
button to light
burners.
Presser le bouton
ON/OFF pour
allumer le bruleur.
ON
OFF
Push ON/OFF
button to turn
burners off.
Presser le bouton
ON/OFF pour
arreter le bruleur.
F
Arrow buttons
Pressing appropriate
directional arrow to
adjusts Hearth Set Point
temperature up or down.
C
WAIT 5 MINUTES BEFORE RELIGHTING
ATTENDRE 5 MINUTES AVANT DE RÉALLUMER
1-800-988-8103
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
Temperature unit selector
Toggles between Fahrenheit
and Celsius temperature
scales in display screens
www.woodstone-corp.com
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
13
MS-5 INITIAL START-UP
Trailered Ovens
Installation and Operation Manual
MS-5 MT ADAMS MODEL INITIAL OVEN START-UP
NOTE: The ceramic materials used in the construction of your Wood Stone oven will absorb moisture if exposed to high humidity
or damp conditions during shipment from the factory or extended periods of storage before installation. Occasionally, through the
course of the initial start-up, as the oven heats up it is possible that you will see some water dripping from the sides of the oven
as moisture is driven out of the ceramic. This is not a defect in the oven, and once the oven has been fully saturated with heat, the
moisture will be driven fully from the oven. After this initial process, you will not see any additional moisture from the oven unless
the oven is not used for an extended period of time AND it is exposed to excessive moisture or high humidity.
NEVER OPERATE THIS OVEN WITH THE STAINLESS STEEL TRANSPORTATION / NIGHT HEAT RETENTION
DOOR IN PLACE. THE DOOR SHOULD ONLY BE USED WHEN THE OVEN IS TURNED OFF!
FIRST DAY
1. Make sure all four propane cylinders are connected. Visually inspect hoses and regulators for any signs of damage.
2. Place chocks or lock the wheels to prevent movement while the oven is in use. Extend flue.
3. There are two banks with two propane cylinders on each bank. Each bank has a changeover valve to select which cylinder on
the bank that will be used. Turn the change over valve to point at the cylinder you will be using. Open the valve on that cylinder.
Do this for each bank. When the oven is running it will be drawing gas from 2 cylinders simultaneously, which will help minimize
condensation and ice build-up on the cylinders. Use the changeover valve to switch cylinders when one runs low or empty.
4. Plug in power supply to the oven. Remove transportation / Night Heat Retention doors from the oven. Make sure the oven flue
is in the extended position (twist and lift). Push I/O button on controller
RFG-IR Model Only: If Hearth Set Point isn't already set set at 100 °F, use the arrows on the controller to set the Hearth Set
Point to 100 °F, its lowest setting. Keep the Hearth Set Point point at 100 °F throughout this process.
Note: This oven utilizes an electronic ignition system and will light automatically. When turning on the oven for the first time, or
if the propane cylinders have previously been allowed to run empty, it may take a minute or so for the gas to purge all the air
from the gas lines. If at any time you smell gas in the area of the oven, turn off the oven immediately then turn off the
propane supply at the cylinders. Check hoses and connections for leaks. Wait 5 minutes to allow any gas to clear
before attempting to restart the oven.
5. Once the burner ignites, adjust the flame to its lowest setting (“1” on the Flame Height Index) and allow the oven to operate at
this setting for about 1 hour.
6. After 4 hours, raise radiant flame to 25% (~5-inch flame).
7. After 4 hours at 25% flame, raise to 50% flame and allow the oven to run until it reaches a temperature of 500 °F. This will take
approximately 3-4 hours.
8. The oven is now ready for use.
NOTE: Small “crazing” cracks will occur with normal heating and cooling. They will not affect the performance or durability of the
oven. If cracks of 1/8" wide or more develop, contact Wood Stone for evaluation.
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
14
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
MS-5 DAILY OPERATION
Trailered Ovens
Installation and Operation Manual
END OF THE DAY
Push I/O button on the controller. All gas will go off, including the pilots. When the oven is turned off, use the Night Heat Retention
Door to help retain heat in the oven. Place the transportation / Night Heat Retention door(s) placed into the oven doorway. Close
tank valves. Retract flue. WARNING: Flue will be hot after use.
DAILY START-UP
1. Remove the transportation / night door(s). Extend the flue. Plug in oven power. Open tank valves.
2. Place chocks or lock the wheels to prevent movement while the oven is in use.
3. Push ON/OFF button. [For RFG-IR Model Only: Adjust the Hearth Set Point on the control panel to the desired floor temperature.]
Using the Flame Height Control Knob, turn the radiant flame to its highest setting. Check your temperature after approximately
one hour. If you are close to your desired temperature, reduce your flame to the holding flame setting that corresponds to your
desired temperature. See the FLAME HEIGHT CONTROL section that follows to determine the proper setting that will correspond
to your desired temperature.
Note for RFG-IR Models Only: It is only possible to program the Hearth Set Point for the underfloor IR burner to temperatures
from 100–800 °F. Once proper temperatures for your application have been established, there should be little or no need to
change the hearth set point. The hearth temperature readout will display “LO” until the oven floor reaches 100 °F.
ALWAYS WAIT 5 MINUTES BEFORE RESTARTING THE OVEN.
NEVER OPERATE THE OVEN WITH THE TRANSPORTATION / NIGHT HEAT RETENTION DOOR(S) IN PLACE.
THIS OVEN IS NOT FOR USE WITH SOLID FUEL
OVEN INTERIOR
Wood Stone recommends the use of long-handled brushes for sweeping up surface debris that will accumulate on the floor of the
oven during use. Use a natural fiber brush—always brushing away from the radiant burner well. For deeper cleaning, use a brass
bristled brush. The oven floor can be then cleaned with a damp rag wrapped around the brass bristled brush head. (Wood Stone
offers an assortment of oven brushes available through your dealer. Specification sheets may be viewed on the Wood Stone website
under Tools & Accessories.)
SANITATION
Wood Stone Mountain Series (MS models) ovens carry an ETL
sanitation listing. The oven interior only is ETL listed to NSF/
ANSI Standard 4 This means that the surfaces of the oven which
are meant to be left exposed after the facade has been put in
place, have been evaluated from the standpoint of sanitation
and food safety and found to comply with NSF/ANSI Standard
4. To operate the oven in accordance with NSF/ANSI Standard
4, only pizza and bread products may be cooked directly on the
floor of the oven. Other types of food may be cooked on or in
pans, or other suitable containers to prevent spillage onto the
oven deck.
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
Transportation / Night Heat
Retention Doors
NOTE: Never operate this
appliance with the stainless
steel Night Heat Retention
Doors in place. The doors
should only be used when
the oven is turned off.
Telescoping flue must be
extended while oven is
operating.
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
15
BL-4355 CONTROLLER
Trailered Ovens
Installation and Operation Manual
CONTROLLER FUNCTIONS
BL-4355 BISTRO MODEL
Temperature
units
Press and hold to
switch between
Fahrenheit
and Celsius.
Hearth Temperature
The floor (hearth)
temperature will be
displayed when the
oven is turned on.
Sensor is embedded
1" below the hearth
surface. Display will
read “LO” when the
temperature is below
100 °F.
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
16
ON/OFF button
Press to turn
oven on and off.
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
BL-4355 INITIAL START-UP
Trailered Ovens
Installation and Operation Manual
BL-4355 INITIAL OVEN START-UP
NOTE: The ceramic materials used in the construction of your Wood Stone oven will absorb moisture if exposed to high humidity
or damp conditions during shipment from the factory or extended periods of storage before installation. Occasionally, through the
course of the initial start-up, as the oven heats up it is possible that you will see some water dripping from the sides of the oven
as moisture is driven out of the ceramic. This is not a defect in the oven, and once the oven has been fully saturated with heat, the
moisture will be driven fully from the oven. After this initial process, you will not see any additional moisture from the oven unless
the oven is not used for an extended period of time AND it is exposed to excessive moisture or high humidity.
NEVER OPERATE THIS OVEN WITH THE STAINLESS STEEL TRANSPORTATION / NIGHT HEAT RETENTION
DOOR IN PLACE. THE DOOR SHOULD ONLY BE USED WHEN THE OVEN IS TURNED OFF!
FIRST DAY
1. Make sure all four propane cylinders are connected. Visually inspect hoses and regulators for any signs of damage.
2. Place chocks or lock the wheels to prevent movement while the oven is in use.
3. There are two banks with two propane cylinders on each bank. Each bank has a changeover valve to select which cylinder on
the bank that will be used. Turn the change over valve to point at the cylinder you will be using. Open the valve on that cylinder.
Do this for each bank. When the oven is running it will be drawing gas from 2 cylinders simultaneously, which will help minimize
condensation and ice build-up on the cylinders. Use the changeover valve to switch cylinders when one runs low or empty.
4. Plug in power supply to the oven. Remove transportation / Night Heat Retention door from the oven. Make sure the oven flue is
in the extended position (twist and lift).
5. Push I/O button on controller to turn the oven on.
Note: This oven utilizes an electronic ignition system and will light automatically. When turning on the oven for the first time, or
if the propane cylinders have previously been allowed to run empty, it may take a minute or so for the gas to purge all the air
from the gas lines. If at any time you smell gas in the area of the oven, turn off the oven immediately then turn off the
propane supply at the cylinders. Check hoses and connections for leaks. Wait 5 minutes to allow any gas to clear
before attempting to restart the oven.
6. Once the burner ignites, make sure the flame is at its lowest setting and allow the appliance to operate at this setting for about
1 hour.
7. After 1 hour, using the Flame Height Control Knob, raise radiant flame to “2” on the Flame Height Index Scale.
8. After 4 hours a raise to “3” on the Flame Height Index Scale and allow the appliance to run until it reaches a temperature of 500
°F. This will take approximately 3–4 hours.
9. The oven is now ready for use.
NOTE: Small “crazing” cracks will occur with normal heating and cooling. They will not affect the performance or durability of the
oven. If cracks of 1/8" wide or more develop, contact Wood Stone for evaluation.
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
17
BL-4355 DAILY OPERATION
Trailered Ovens
Installation and Operation Manual
END OF THE DAY
Push I/O button on the controller. All gas will go off, including the pilots. When the oven is turned off, use the Night Heat Retention
Door to help retain heat in the oven. Place the transportation / Night Heat Retention door(s) into the oven doorway. Close tank valves.
Retract flue. WARNING: Flue will be hot after use.
DAILY START-UP
1. Remove the transportation / night door(s). Extend the flue. Plug in oven power. Open tank valves.
2. Place chocks or lock the wheels to prevent movement while the oven is in use.
3. Push I/O button on the controller to to the oven on. Turn the radiant flame to its highest setting using the Flame Height Control
Knob. The oven should reach the desired cooking temperature typically within 2 hours. Use the Flame Height Control Knob to
control the amount of heat in the oven. See the FLAME HEIGHT CONTROL section that follows to determine the proper setting
that will correspond to your desired temperature.
See woodstone-corp.com for detailed information on cooking in your Wood Stone oven.
OVEN INTERIOR
Wood Stone recommends the use of long-handled brushes for sweeping up surface debris that will accumulate on the floor of the
oven during use. Use a natural fiber brush—always brushing away from the radiant burner well. For deeper cleaning, use a brass
bristled brush. The oven floor can be then cleaned with a damp rag wrapped around the brass bristled brush head. (Wood Stone
offers an assortment of oven brushes available through your dealer. Specification sheets may be viewed on the Wood Stone website
under Tools & Accessories.
NEVER PLACE ANYTHING IN OR ABOVE THE RADIANT FLAME
ALWAYS WAIT 5 MINUTES BEFORE RESTARTING THE OVEN.
THIS OVEN IS NOT FOR USE WITH SOLID FUEL
SANITATION
Wood Stone Mountain Series (MS models) ovens
carry an ETL sanitation listing. The oven interior only
is ETL listed to NSF/ANSI Standard 4 This means
that the surfaces of the oven which are meant to be
left exposed after the facade has been put in place,
have been evaluated from the standpoint of sanitation
and food safety and found to comply with NSF/ANSI
Standard 4. To operate the oven in accordance with
NSF/ANSI Standard 4, only pizza and bread products
may be cooked directly on the floor of the oven. Other
types of food may be cooked on or in pans, or other
suitable containers to prevent spillage onto the oven
deck.
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
18
Transportation / Night Heat
Retention Doors
NOTE: Never operate this
appliance with the stainless
steel Night Heat Retention
Doors in place. The doors
should only be used when
the oven is turned off.
Telescoping flue must be
extended while oven is
operating.
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
FLAME HEIGHT CONTROL
Trailered Ovens
Installation and Operation Manual
DETERMINING THE APPROPRIATE FLAME HEIGHT
For each specific configuration of oven there is a system that determines what the desired flame height will be. Each flame height
corresponds to a saturated floor temperature. Several factors need to be accounted for in order to determine this relationship for
each oven.
USING THE FLAME HEIGHT INDICATOR SCALE
Heat Up Flame: Set the Flame Height Pointer at “5” (highest setting) on the Flame Height Index Scale until desired
temperature is reached.
Holding Flame: Using the Flame Height Control Knob, set the flame height to “3” (~8–9" flame) on the Flame Height Index Scale
for desired temperature of 570–600 °F. Set the flame height to “2” (~5–6" flame) for desired temperature of 450–480 °F.
Cooking Flame: After introducing the pizza/product into the oven, visually raise the flame to approximately 3 inches higher than
the Holding Flame.
Return the Flame Height Control Knob to the Holding Flame position after removing the pizza/product from the oven.
THE COOKING FLAME HAS TWO PURPOSES:
1. To bake the top of the pizza/product as fast as the bottom of the pizza/product.
2. To help replace heat to the floor (hearth) that is lost during production cooking.
Note: The settings recommended on the Flame Height Index Scale for specific flames are based on ovens that have been installed
according to specifications. Individual results may vary slightly.
FLAME HEIGHT INDICATOR
Comprised of two parts
Flame Height Index Scale
Flame Height Control Knob
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
For more information regarding Flame Height
Control, go to the Resource Center section of
our web site at:
www.woodstone-corp.com
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
19
CLEANING
Trailered Ovens
Installation and Operation Manual
CLEANING THE OVEN
Clean as needed­—multiple times per hour depending on production. Wood Stone recommends the use of long-handled brushes
for sweeping up surface debris that will accumulate on the floor of the oven during use. Use a natural fiber brush, always brushing
away from the radiant burner well to the doorway where it can be easily removed with a dough cutter or spatula. For deeper
cleaning, use a brass bristled brush. The oven floor can be then cleaned with a damp (not wet) rag wrapped around the brush head.
Wood Stone offers an assortment of oven brushes available through your dealer. Specification sheets may be viewed on the Wood
Stone website under Tools & Accessories.
OVEN EXTERIOR
All painted and stainless steel surfaces should be cleaned as necessary using a mild detergent, hot water and a soft cloth or
sponge. Stubborn residues may be removed using a nonmetallic scouring pad. When scouring stainless steel surfaces, scrub with
the grain of the metal to prevent scratching.
BL-4355 ONLY: BURNER TRAY
At 6–12 month intervals, depending on the amount of usage, the burner tray beneath the oven should be removed and
emptied of any accumulated debris. To remove: unscrew the wing nut at the back of the burner tray. There should be
very little debris in the tray if the oven is being operated properly.
NEVER PLACE ANYTHING IN OR ABOVE THE RADIANT FLAME.
NEVER SWEEP DEBRIS INTO THE RADIANT BURNER. THIS CAN CAUSE THE BURNER TO CUT OUT, DAMAGE BURNER
COMPONENTS, AND/OR EFFECT BURNER PERFORMANCE. PROBLEMS CAUSED BY DEBRIS IN THE RADIANT BURNER WILL
NOT BE COVERED BY THE OVEN WARRANTY.
NEVER USE ICE, EXCESSIVE WATER, ANY LIQUID, OR ANY TYPE OF CLEANING CHEMICAL ON THE OVEN FLOOR. DOING SO
CAN SEVERELY DAMAGE THE OVEN CERAMIC AND THIS DAMAGE WILL NOT BE COVERED UNDER WARRANTY.
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
20
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
PERIODIC THERMAL CLEANING
Trailered Ovens
Installation and Operation Manual
ESTABLISHING A THERMAL CLEANING SCHEDULE
Wood Stone ovens are typically operated at temperatures which preclude the need for cleaning of the interior walls and ceiling (the
dome) of the oven. If, however, you routinely operate the oven at floor temperatures lower than 450 °F, you may notice a buildup
on the interior walls and/or ceiling of the oven. If this is the case, use the following procedure to periodically clean the oven. The
frequency of thermal cleaning will be determined by the amount of buildup experienced.
THERMAL CLEANING
If a Wood Stone gas-fired oven is operated at low temperatures (below 450 °F), it is possible that grease from food could condense
on the walls and ceiling of the oven. To remove the grease that has accumulated on the walls and ceiling of the oven, simply turn
the radiant flame to its highest setting. Monitor the floor temperature displayed on the controller. When the floor reaches 600 °F,
lower the flame slightly so as to maintain the oven floor temperature near 600 °F for about an hour. Once the oven dome appears
clean, allow the oven to return to normal operating temperatures and continue normal operation.
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
21
TROUBLESHOOTING
Trailered Ovens
Installation and Operation Manual
PROBLEMCAUSE/SOLUTION
Controller will not turn on
1. Incoming power to oven turned off. Check circuit breaker for circuit supplying
the oven. Check that any wall switches external to the oven that control oven
power are turned on. Check that any interlocks external to the oven are turned
on.
2. If controller still does not turn on, please contact Wood Stone for assistance.
Radiant flame does not light
1. Is gas turned on to the oven? Is gas shut-off valve turned all the way on?
2. Debris in burner. Burner may require cleaning. Contact Wood Stone for
assistance.
3. Damaged igniter or gas valve. Contact Wood Stone for assistance.
If the oven is being started for the first time:
Has all air been bled from the gas line?
Is the switch on the SV-2 valve in the ON position?
NOTE MS-5: Valve is located beneath the oven at the rear, towards the
side where the radiant burner is located.
NOTE BL-4355: Valve is locate on the back of the control box, beneath the
oven
MS-5-RFG-IR MODEL ONLY
Controller display reads “Chec”
Underfloor burner did not fire when the floor temperature dropped below the
Hearth Set Point. Contact Wood Stone for assistance.
Underfloor burner is not running.
“Hearth Heat” light is off.
Hearth temperature is above the Hearth Set Point.
Hearth Temperature is above the
Hearth Set Point.
This is normal. Radiant (dome) flame can drive the temperature over the Hearth
Set Point. The Hearth Set Point only controls the underfloor (hearth) burner. Turn
down the dome flame if needed.
BL-4355 ONLY
Controller display reads “OPEN”
1. Thermocouple is not plugged into control box.
2. Damaged thermocouple. Contact Wood Stone for assistance.
Please contact Wood Stone at 1-800-988-8103 should service be necessary, or if you have any questions about your
oven. Our service hours are 8am to 4:30pm Pacific Standard Time. Follow the recorded instructions for Emergency
Service if you require assistance during non-business hours. A Wood Stone technician will promptly respond to your call.
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
22
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
MS-5 OPERATIONAL SEQUENCE
Trailered Ovens
Installation and Operation Manual
BURNER OPERATION SEQUENCE
MS-5 RFG OVEN
Power on.
SV2 valve powers igniter and opens pilot
valve.
Pilot does not light–SV2 times out.
Touch-style controllers will flash “chec”.
Pilot lights.
SV2 senses pilot flame, turns
igniter off–SV2 opens. Burner
lights. Amber light comes on or, on
touchpad-style controllers, dome
light comes on.
Burner remains on until oven
control is turned off.
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
23
MS-5 OPERATIONAL SEQUENCE
Trailered Ovens
Installation and Operation Manual
BURNER OPERATION SEQUENCE
MS-5 RFG-IR OVEN - TOUCH PAD CONTROLLERS
Power on.
SV-2 valve powers igniter and opens
pilot valve for radiant (rear) burner.
Pilot lights.
Pilot does not light–SV-2 times out.
Floor temperature above
Hearth Set Point–Controller
does not power SV1
(underfloor burner).
Pilot does not light–SV-1
times out. Touchpad
controller flashes “chec”.
SV-2 senses pilot flame.
Igniter off–SV-2 opens.
Burner lights. Dome
Flame indicator light
comes on.
Floor temperature below Hearth
Set Point–Controller sends power
to SV1. SV1 powers igniter and
opens pilot valve.
Radiant burner remains
on until oven control is
turned off.
Pilot lights–SV-1 senses pilot
flame. Igniter off. Hearth Heat light
on. SV1 opens. Underfloor burner
lights.
Floor reaches the Hearth Set Point
temperature–Controller turns off
power to SV-1.
Underfloor burner shuts off.
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
24
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
BL-4355 OPERATIONAL SEQUENCE
Trailered Ovens
Installation and Operation Manual
BURNER OPERATION SEQUENCE
RFG OVEN - TOUCH PAD CONTROLLERS
Power on.
SV-2 valve powers igniter and opens
pilot valve for radiant (rear) burner.
Pilot lights.
Pilot does not light–SV2 times out.
Controller display will flash “chec”.
SV-2 senses pilot flame.
Igniter off–SV-2 opens.
Burner lights.
Radiant burner remains
on until oven controller is
turned off.
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
25
MS-5 ELECTRICAL DIAGRAM
Trailered Ovens
Installation and Operation Manual
MS-5 MT ADAMS ELECTRICAL DIAGRAM
RFG 120 VAC MODELS WIRE DIAGRAM
TYPE 4 CONTROLLER
See equipment data plate for correct voltage of your oven.
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
26
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
MS-5 ELECTRICAL DIAGRAM
Trailered Ovens
Installation and Operation Manual
MS-5 MT ADAMS ELECTRICAL DIAGRAM
RFG-IR 120 VAC MODELS WIRE DIAGRAM
TYPE 2 CONTROLLER
See equipment data plate for correct voltage of your oven.
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
27
BL-4355 ELECTRICAL DIAGRAM
Trailered Ovens
Installation and Operation Manual
BISTRO MODELS WITH HOT SURFACE IGNITION
RFG 120 VAC MODELS WIRE DIAGRAM
100-120 VAC, 50-60 Hz
wired by others
As specified on equipment data plate
See equipment data plate for correct voltage of your oven.
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
28
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
LIMITED WARRANTY
Trailered Ovens
Installation and Operation Manual
ALL WARRANTY SERVICE MUST BE PRE-APPROVED BY WOOD STONE
Wood Stone warrants its equipment to the original purchaser against defects in material or manufacture for a period of one
year from the original date of purchase, subject to the following exclusions and limitations.
Please contact the factory first at 1.800.988.8103 or 1.360.650.1111, seven days a week. Our normal business hours are 8am
to 4:30pm PST Monday–Friday. If calling during non-business hours, follow the recorded instructions for emergency service
and a Wood Stone technician will get back to you promptly.
EXCLUSIONS
The warranties provided by Wood Stone do not apply in the following instances:
1. In the event that the equipment is improperly installed. Proper installation is the responsibility of the installer; proper installation
procedures are prescribed by the Wood Stone Installation and Operation Manual.
2. In the event the equipment is improperly or inadequately maintained. Proper maintenance is the responsibility of the user; proper
maintenance procedures are prescribed in the Wood Stone Installation and Operation Manual. Burner problems resulting from debris
or ash in the burner well will not be covered by the warranty. Call with questions regarding maintenance frequency.
3. In the event that the failure or malfunction of the appliance or any part thereof is caused by abnormal or improper use or is otherwise
not attributable to defect in material or manufacture.
4. In the event that the appliance, by whatever cause, has been materially altered from the condition in which it left the factory.
5. In the event that the rating plate has been removed, altered or obliterated.
6. On parts that would be normally worn or replaced under normal conditions.
7. Normal cracking due to expansion and contraction stress relief in the ceramic firebox.
8. In wood-fired equipment configurations, in the event that pressed log products of any type have been burned in the equipment.
9. In coal-fired oven configurations, in the event any type of coal other than anthracite coal fuel has been used.
10.Damage resulting from the use of chemical cleaning products in the oven, as well as any damage from liquids or chemicals, including
water, being poured or sprayed into the oven.
If any oral statements have been made regarding this appliance, such statements do not constitute warranties and are not part of the
contract of sale. This Limited Warranty constitutes the complete, final and exclusive statement with regard to warranties.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER WRITTEN, ORAL OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE OR WARRANTY AGAINST LATENT DEFECTS.
LIMITATIONS OF LIABILITY
In the event of warranty claim or otherwise, the sole obligation of Wood Stone shall be the repair and/or replacement, at the option of
Wood Stone, of the appliance or component or part thereof. Such repair or replacement shall be at the expense of Wood Stone with the
exception of travel over 100 miles or two hours, overtime, and holiday charges which shall be at the expense of the purchaser. Any repair
or replacement under this warranty does not constitute an extension of the original warranty for any period of the appliance or for any
component or part thereof. Parts to be replaced under this warranty will be repaired or replaced at the option of Wood Stone with new
or functionally operative parts. The liability of Wood Stone on any claim of any kind, including claims based on warranty, expressed or
implied, contract, negligence, strict liability or any other theories shall be solely and exclusively the repair or replacement of the product
as stated herein, and such liability shall not include, and purchaser specifically renounces any rights to recover, special, incidental,
consequential or other damages of any kind whatsoever, including, but not limited to, injuries to persons or damage to property, loss of
profits or anticipated profits, or loss of use of the product.
TO SECURE WARRANTY SERVICE
If you claim a defect covered by this Limited Warranty, contact:
Wood Stone Corporation, Attn: Service Department, 1801 W. Bakerview Rd., Bellingham, WA 98226 USA
Phone 1.800.988.8103 or 1.360.650.1111
An ongoing program of product improvement may require us to change
specifications without notice. Trailered Ovens, Revised January 2014.
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
29