macro machines storage strip manual ____________________________________________________ Storage and Recall Module_________________________________ The Storage Strip allows for saving and recalling settings in supported modules. You can manually recall stored settings using the lower group of 4 buttons. There are 4 banks of 4 stored settings, 4x4=16 total settings. ____________________________________________________ /// 2014 macromachines.net macro machines storage strip manual ____________________________________________________ Sequencing Modes________________________________________ Any signal coming into the clock input will sequence through the settings in different patterns according to the currently selected mode. To select a sequencing mode press and hold (save / +) and (- / bank) buttons simultaneously. Then press one of the bottom 4 mode/bank select buttons. These correspond to Forward, Reverse, Pendulum, and Random modes. By default the Storage Strip sequences through 4 steps within the selected bank. In order to enter 16 step mode hold the following buttons simultaneously: (bank / -, and .) To return to 4 step mode press : (bank / -, and ). note: the leds will only show active settings within the currently selected bank. Zoom Buttons____________________________________________ Zoom In (+) also functions as a save button. Pressing (+ / save) along with one of the bottom 4 storage location buttons saves to that location. Zoom Out (-) also functions as a bank selection button. Pressing (- / bank) and then a setting button will change to that bank (1-4). Module Compatibility______________________________________ To view a list of current supported modules go to: http://macromachines.net/products/storage-strip/compatibility/ Mungo specific features: The Storage Strip replaces the functionality of the Mungo zoom switch with a 2 button system for Zoom In and Zoom Out. ____________________________________________________ /// 2014 macromachines.net macro machines storage strip manual ____________________________________________________ Installation______________________________________________ Connect the 16-pin ribbon cable to the module with the orientation of the red stripe matching the line marked -12. Control data from the Storage Strip is sent along the CV rail of the busboard. Ensure all modules to be controlled by the Storage Strip are on the same busboard. A 2HP bus access utility module allowing chaining of the CV and Gate rails will be available soon. Warning: Do not install the Storage Strip on the same row as any Doepfer modules which are configured to send voltage to the CV/Gate bus. There are 2 male header pins labeled zoom, to allow compatibility with Mungo Enterprises 0 line of eurorack modules, use the provided female jumper cable to connect up to 2 Mungo modules directly to the Storage Strip. To chain additional Mungo 0 modules, connect a female jumper cable to the zoom chaining pin on the back of any directly connected Mungo 0 module. ____________________________________________________ /// 2014 macromachines.net macro machines storage strip manual ____________________________________________________ One Year Limited Warranty______________________________________________________ Macro Machines Engineering, inc. warrants that your new product, when purchased at an authorized dealer, shall be free of defects in materials and workmanship for a period of one (1) year from the original date of purchase. Please contact Macro Machines for information on warranty and service outside of the USA. During the warranty period, Macro Machines shall, at its sole option, either repair or replace any product that proves to be defective upon inspection by a representative of Macro Machines. Macro Machines reserves the right to update any unit returned for repair and to change or improve the design of the product at any time without notice. Service and repairs of Macro Machines products are to be performed only by a licensed representative of Macro Machines.. Unauthorized service, repair or modification will void this warranty. DISCLAIMER AND LIMITATION OF WARRANTY THE FOREGOING WARRANTY IS THE ONLY WARRANTY GIVEN BY MACRO MACHINES AND IS IN LIEU OF ALL OTHER WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR PURPOSE, EXCEEDING THE SPECIFIC PROVISIONS OF THIS WARRANTY ARE HEREBY DISCLAIMED AND EXCLUDED FROM THIS WARRANTY. UPON EXPIRATION OF THE APPLICABLE EXPRESS WARRANTY PERIOD (1 YEAR), MACRO MACHINES SHALL HAVE NO FURTHER WARRANTY OBLIGATION OF ANY KIND, EXPRESS OR IMPLIED. MACRO MACHINES SHALL IN NO EVENT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES SUFFERED BY THE PURCHASER OR ANY THIRD PARTY, INCLUDING WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS OR BUSINESS, OR DAMAGES RESULTING FROM USE OR PERFORMANCE OF THE PRODUCT, WHETHER IN CONTRACT OR IN TORT. MACRO MACHINES SHALL NOT BE LIABLE FOR ANY EXPENSES, CLAIMS, OR SUITS ARISING OUT OF THE FOREGOING. The Macro Machines Warranty DOES NOT Cover: ● Damage from physical abuse such as dropping the unit, impact from hard objects or damage to external components as a result of negligence. ● Damage due to liquid contamination. ● Damage resulting from any use other than that it was intended for. ● Any unit that has been repaired or had an attempted repair made to it by unauthorized personnel. ● Damage due to incorrect connection, connection to faulty equipment or connection to faulty or incorrect power supplies. ● Damage in transit as a result of inadequate packaging or protection. 1. MACRO MACHINES RESERVES THE RIGHT TO WITHHOLD SERVICE. 2. NONWARRANTY SERVICE INCURS A $25 LABOR FEE FOR DOMESTIC REPAIRS. SLIGHTLY MORE FOR INTERNATIONAL SHIPPING CHARGES. If, after reading this warranty, you feel your Macro Machines product still qualifies as a warranty repair, contact Macro Machines by email at [email protected] to arrange a repair. ____________________________________________________ /// 2014 macromachines.net