1. law, govt and politics
2. government
3. legislative

INSTRUCTION MANUAL
FOR THE SURVIVOR FILTER TM
Please Save These Instructions
Please read these instructions carefully
before using the SURVIVOR FILTER TM
(Failure to follow all directions may invalidate warranty)
Copyright Harriston Products July 2014
PRECAUTIONS
The Survivor Filter TM personal water filter is
intended for use with Fresh Water sources only.
DO NOT USE WITH SALT WATER
The Survivor Filter TM personal water filter is a
precision device. Please always follow all
assembly, disassembly, cleaning and
maintenance instructions in order to allow
trouble free and reliable performance.
Copyright Harriston Products July 2014
How the product works
• What kind of filter does it have?
• How does it remove particles?
• Ultrafilitration
• Carbon Filter
• Does it have any proof that it works? Can we make
any statements on how it works?
• I need info for this section in order to add
information to it. This section serves as both an
advertisement and as a guide to the product before
the specifics.
• What is the product designed for. Backbacking,
trecking etc.
• Does the product come pre-assembled and ready
for use?
Copyright Harriston Products July 2014
Key Components
Copyright Harriston Products July 2014
NORMAL OPERATION
SURVIVOR FILTER TM
1. Open cover (Figure 6) to expose mouthpiece (Figure 1)
2. Insert water inlet (Figure 7) directly into the fresh water source.
3. Blow gently into the filter tip ( Figure 1) to remove any air lock.
4. Gently suck in water from the mouthpiece (Figure 1) and drink.
Copyright Harriston Products July 2014
OPERATION WITH PLASTIC
BOTTLE
TM
SURVIVOR FILTER
1. Fill a 28mm threaded plastic soda bottle with water from a fresh water
source.
2. Screw the soda bottle into the water inlet (Figure 7).
3. Invert the soda bottle and the Survivor Filter vertically and allow the
filtered water to flow out of the mouthpiece (Figure 1) of the Survivor
Filter, into a cup or other clean receptacle
Copyright Harriston Products July 2014
OPEATION WITH OPTIONAL WATER BAG
(not included)
SURVIVOR FILTER TM
1. Fill the Optional water bag with water from the fresh water source. Allow
some water to flow out of attached water bag hose to displace air, then
clamp off.
2. Attach the Survivor Filter water inlet (Figure 7) to the end of the water bag
hose.
3. Hang water bag and allow filtered water to flow out of the Survivor Filter
mouthpiece (Figure 1) and into a clean cup or receptacle.
4. Please refer to picture above.
Copyright Harriston Products July 2014
ASSEMBLY & DISASSEMBLY
SURVIVOR FILTER TM
The Survivor Filter TM personal water filter is a precision device.
Please always follow Assembly & Disassembly instructions in order to
avoid any damage to the Survivor Filter TM
The Carbon Filter (Figure 2) friction fits into the top of the ABS Shell
(Figure 5) and locks into place using the indicated slots (X) on either
side of the ABS Shell. There are plastic buttons on the Carbon Filter
(Figure 2) which lock behind the indicated slots when the Carbon
Filter (2) is rotated in the LOCK position
WARNING: DO NOT attempt to pull the Carbon Filter (2)
away from the ABS Shell (5) when it is in the LOCK
position, the locking mechanism on the ABS Shell (5) will
break and is not covered by warranty.
Carbon Filter (2)
ABS Shell (5)
X
Y
Copyright Harriston Products July 2014
ASSEMBLY & DISASSEMBLY
SURVIVOR FILTER TM
DISASSEMBLY of FILTER-TIP (1) and CARBON FILTER 2
1. Hold the Survivor Filter TM horizontally. Carefully rotate the
Carbon Filter (Figure 2) slightly into the UNLOCK position (ie: until
the plastic buttons are not obstructed by the indicated slots).
2. Then gently pull the Carbon Filter (Figure 2) away from the ABS
Shell (Figure 5) in a horizontal motion.
Carbon Filter (2)
ABS Shell (5)
X
Y
Copyright Harriston Products July 2014
ASSEMBLY & DISASSEMBLY
SURVIVOR FILTER TM
DISASSEMBLY of Connector (Water Inlet) (7)
Note: The Water Inlet (Figure 7) screws into the bottom of the ABS Shell
(Figure 5) in a CLOCKWISE fashion.
1. Hold the Survivor Filter TM horizontally.
2. Carefully unscrew the Water Inlet (Figure 7)
COUNTERCLOCKWISE.
3. Take care not to misplace the Mesh Pre-Filter (4).
4. Refer to Picture Below.
Unscrew the Water Inlet) (7) COUNTERCLOCKWISE
Water Inlet (7)
Copyright Harriston Products July 2014
ABS Shell (5)
ASSEMBLY & DISASSEMBLY
SURVIVOR FILTER TM
REMOVAL of UF Filter (Figure 3)
Note: The UF Filter (Figure 3) is inside the ABS Shell (Figure 5).
1. Hold the Survivor Filter TM horizontally as shown.
2. Carefully push the UF Filter at the bottom of the ABS Shell
(Figure 5), as shown to eject the UF Filter (Figure 3).
3. Step 3 Continued on Next Page
Bottom of ABS
Shell (5)
Copyright Harriston Products July 2014
ASSEMBLY & DISASSEMBLY
SURVIVOR FILTER TM
REMOVAL of UF Filter (3) continued
3. The UF Filter (3) is ejected from the ABS Shell (5), as
shown below.
4. Take care not to misplace the round plastic grate (with
holes) which fits at the top the ABS Shell (5).
The UF Filter (3) is ejected
Bottom of ABS
Shell (5)
Copyright Harriston Products July 2014
Cleaning & Maintenance
of Your
SURVIVOR FILTER TM
The Survivor Filter TM personal water filter is a precision device. Please always
follow all assembly, disassembly, cleaning and maintenance instructions in order
to allow trouble free and reliable performance.
Filter Replacement: Replacement of the UF and the Carbon filters depend
on how frequently the Survivor Filter TM is used and the quality of the fresh water
sources employed. In general, the manufacturer recommends that the filters be
changed at least annually.
Cleaning: Your Survivor Filter TM should be cleaned with fresh clean water
after each use. To remove dirt and excess water, shake the Survivor Filter TM
water inlet in a downward motion with a snapping motion of the wrist.
Cleaning Solutions: DO NOT use commercial cleaning solutions or
chemicals to clean your Survivor Filter TM . You should only use clean fresh
water to rinse the filters. Vinegar may be used to clean the UF Filter (3) ONLY.
The UF Filter (3) ONLY can be removed and soaked in vinegar for 20 minutes if
dirty, then flushed with clean water and left to dry before re-assembly. WARNING:
DO NOT soak the Carbon Filter (2) in vinegar as this will shorten the life of
the Carbon Filer.
Before STORING your Survivor Filter TM for more than 15 days, the UF Filter
(3) should be removed and soaked in vinegar for 20 minutes, then flushed with
clean water and left to dry before re-assembly.
Storage: Store your Survivor Filter TM in a clean and dry place. Avoid exposure
to direct sunlight and store away from excessive heat sources. Some customers
report that their Survivor Filter TM stays clean and fresh if stored in the
refrigerator..
Copyright Harriston Products July 2014
SPECIFICATIONS
SURVIVOR FILTER TM
Model:
Survivor Filter L600
Filtration:
Up to 0.05 microns
Weight:
100 Grams
Size:
180 mm X 35 mm
Capacity:
1000 liters
Water Flow:
200 ml/minute
Material:
ABS, Carbon Filter,
UF (Medical Grade)
The SURVIVOR FILTER TM is manufactured for and
distributed by HARRISTON PRODUCTS. Replacement
parts and filters may be purchased at
www.harristonproducts.com.
Made in China
Copyright Harriston Products July 2014