Cordless Manual Roller Shade English 1

Cordless Manual Roller Shade
English
Installation and Setup Guide—Please Read Before Installing and Operating
SHADE WITH FASCIA - included in the box:
1 SHADE WITH FASCIA - Mounting the back cover: ! CAUTION:
RISK OF FALLING OBJECTS. Securely install
the shade system per the mounting instructions. Failure to do
so could result in minor or moderate injury.
A
B
Back Cover
Mounting Screws
(qty varies with
shade size)
1.1 Hold the Back Cover A up to the mounting surface.
Approximate its final position centered on the window, and use
a pencil to mark mounting screw locations on the Back Cover.
To ensure the Back Cover is properly mounted, we recommend:
a.Install a mounting screw 2 - 5 in (51 - 127 mm) from each end of the
Back Cover.
2 - 5 in (51 - 127 mm)
D
C
Cordless Manual Roller Shade Assembly
Spacers (included
only when outside
mount above trim is
specified - qty varies
with shade size)
SHADES UP TO
48 in (1219 mm)
2 - 5 in (51 - 127 mm)
2 - 5 mm),
in (51 install
- 127 mm)
b.For shades wider than 48 in (1219
two additional mounting
SHADES UP TO
screws,
equally
spaced
across
the
Back
Cover.
DO NOT install a
SHADES
48 in (1219 mm)
WIDER
THAN
screw
at the center of the Back Cover.
48 in (1219 mm)
E
(See reverse for mounting instructions.)
F
MOUNTING
OPTION:
MOUNTING
OPTION:
Inside
Mount
Outside Mount
above Trim
B
A
B
Equal space
both sides
A
Spacers D
between the Back
Cover and the
mounting surface
(included only when
outside mount above
trim is specified)**
B
**NOTE: Depending on the size
of your shade and the depth
of your trim, you may be able
to mount the shade directly to
the wall above the trim without
using the spacer blocks.
MOUNTING
OPTION:
d.Verify that the Back Cover is level, centered on, and parallel to, the
window opening.
A
to the mounting surface using the mounting screws
B
NOTE:
Ensure the
Back Cover
is centered in
the window
opening.
There must be
equal space
between each
end and the
side trim.
EQUALLY SPACED
c.Locate the mounting screws so that they drive into studs or solid trim.
For other surfaces, use appropriate expansion anchors, toggle bolts,
or other fasteners (not included).
1.2 Pre-drill the Back Cover
A,
Equal depth
both sides
EQUALLY SPACED
SHADE WITHOUT FASCIA - included in the box:
1.3 According to the mounting option chosen on the original order, fasten the Back Cover
provided B or other appropriate fasteners.
2 - 5 in (51 - 127 mm)
SHADES
WIDER THAN
48 in (1219 mm)
Fascia
(NOTE: If you are installing a shade without fascia, proceed directly to section 4 at the top of page 2.)
at the pencil marks.
Outside
Mount
on Trim
B
In this arrangement, the top
of the back cover must be a
minimum of 5 1/4 in (133 mm)
above the top of the trim.
A
Align the
top of the
Back Cover
with the top
edge of
the trim
5.25 in
(133 mm)
min.
B
Wall
Trim
NOTE: The Back Cover features grooves to help stabilize the point of
your drill bit.
Mounting Brackets
(2 or 3 depending
on shade width)
G
Mounting
Screws
(same qty
as brackets)
H
Cordless Manual Roller
Shade Assembly
Other items you’ll need:
2 SHADE WITH FASCIA - Hanging the shade:
3 SHADE WITH FASCIA - Installing the fascia:
2.1 Rest the inner part of the end brackets (shaded below) and the center support, if applicable,* on the lower tab of
the mounted Back Cover.
3.1 Route the power wire clear of the shade, ensuring it is secured in a position where it
will not interfere with shade movement.
2.2 Push the top of the Shade Assembly into the Back Cover until each end bracket and the center support, if
applicable,*locks in with a CLICK!
3.2 Insert the tongue on the inside of the fascia into the upper slots of the end brackets
and the center support, if applicable,*.
CLICK!
CLICK!
CLICK!
CLICK!
Center
Support
1/8 in (3.2 mm) Drill Bit
A
C
#2 Phillips Driver Bit
Power wire
connects to
power supply
(see section 5
on page 2)
Pencil
Power Drill
*NOTE: The Center Support
is included only with
shades 53 in (1346 mm)
wide and wider.
Level
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
E
01/2014
P/N 045440 Rev. A
Lutron and O are registered trademarks of Lutron Electronics Co., Inc.
Cordless Manual Roller Shade Installation and Setup Guide
Page 2
5 Tension Adjustment (OPTIONAL):
4 SHADE WITHOUT FASCIA - Mounting the shade:
NOTE: If you followed Sections 1 - 3 on page 1 to mount a shade with fascia, skip this section.
NOTE: Ensure the shade is fully raised before making any adjustments.
Adjust in small steps; recheck for the desired performance frequently.
! CAUTION: RISK OF FALLING OBJECTS. Securely install the shade system per the mounting instructions.
Failure to do so could result in minor or moderate injury.
4.1 Hold the shade assembly
mounting surface.
a.Install a bracket
F
H
6 Upstop Adjustment (OPTIONAL):
5 in (127 mm)
7 in (178 mm)
up to the mounting surface. Approximate its final position and use a pencil to mark screw locations on the
5 in (127 mm)
5.1 Increase tension.
NOTE: Ensure the shade is fully raised before making any adjustments.
Adjust in small steps; recheck for the desired performance frequently.
6.1 Lower the bottom bar.
7 in (178
mm)
If the shade
rises
slowly, and/or the shade does not retract fully, use a
flat-blade screwdriver to increase the spring tension.
Retract the shade, allowing it to stop at the top. If the bottom bar
stops too high, use a flat-blade screwdriver to lower the upstop.
Regular Roll
Reverse Roll
Regular Roll
Reverse Roll
Turn the adjuster on
the left end clockwise
Turn the adjuster on the
right end clockwise
Turn the adjuster on the
right end clockwise
Turn the adjuster on the
left end clockwise
5 - 7 in (127-178 mm) from each end of the shade.
b.Locate the brackets so that the mounting screws
bolts, or other fasteners (not included).
G
drive into studs or solid trim. For other surfaces, use appropriate expansion anchors, toggle
c.Verify that the mounted brackets are positioned to hold the shade system level, centered on, and parallel to, the window opening.
4.2 According to the mounting option chosen on the original order, fasten the Mounting Brackets
mounting screws provided G or other appropriate fasteners.
MOUNTING OPTION:
MOUNTING OPTION:
Inside Mount
Outside Mount
5 in (127 mm)
SHADE WIDTH
5 in (127 mm)
7 in (178 mm)
7 in (178 mm)
Bracket
Zone
F
F
, to the mounting surface using the
5 in (127 mm)
5 in (127 mm)
SHADE WIDTH
7 in (178 mm)
Bracket
Zone
Center bracket included only
with shades 53 in (1346 mm)
wide and wider
Center bracket included only
with shades 53 in (1346 mm)
wide and wider
Mount brackets with release
tab pointing toward the room
Mount brackets with release
tab pointing downward
7 in (178 mm)
5.2 Decrease tension.
6.2 Raise the bottom bar.
If the shade resists pulling down, and/or raises too quickly, use a
flat-blade screwdriver to decrease the spring tension.
Retract the shade, allowing it to stop at the top. If the bottom bar
stops too low, use a flat-blade screwdriver to raise the upstop.
Regular Roll
Reverse Roll
Regular Roll
Turn the adjuster on the
left end counter-clockwise
Turn the adjuster on the right
end counter-clockwise
Turn the adjuster on the
right end counter-clockwise
Reverse Roll
F
Turn the adjuster on the left
end counter-clockwise
4.3 Hook the lip of the shade bar on the brackets, then swing the other side of the bar into the brackets until it locks into each bracket with
an audible CLICK!
5 in (127 mm)
Inside Mount
Outside Mount
7 in (178 mm)
H
H
For complete warranty information, please see: http://www.lutron.com/TechnicalDocumentLibrary/Window Systems Warranty.pdf
Worldwide Headquarters | USA
Lutron Electronics Co., Inc. 7200 Suter Road, Coopersburg, PA 18036-1299 USA
TEL: 1.610.282.3800 • FAX: 1.610.282.3090
Technical Support: 1.800.523.9466 • Toll Free: 1.888.LUTRON1
Email: [email protected] • Online: www.lutron.com/shadingsolutions
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
01/2014
P/N 045440 Rev. A
Europe Headquarters | United Kingdom
Lutron EA Ltd. 6 Sovereign Close, London, E1W3JF, UK
TEL: +44.(0)20.7702.0657 • FAX: +44.(0)20.7480.6899
Technical Support: +44.(0)20.7680.4481
FREEPHONE: 0800.282.107
Lutron and O are registered trademarks of Lutron Electronics Co., Inc.