1. No category

Wiring length and wire requirement
Connection diagram for 1 monitor with 1 outdoor camera and 3 CCTV camera
Wiring length
Wiring material requirement between main indoor monitor and outdoor camera
Wiring material requirement between main monitor and sub monitor
Electronic lock
CCTV input wiring material requirement
A/V output wiring material
Outdoor camera
The resistance rate for the wire should be ≤ 0.06Ω/m
In order to make sure best quality and operation, please choose the wire according to the above form, the distance between outdoor camera and the last indoor monitor
should be ≤100m.
Electric lock power
S702C
Connection diagram of indoor monitor and outdoor camera (1-1)
CCTV camera 1
CCTV camera 2
CCTV camera3
Electronic lock
Outdoor camera
Electric lock power
Monitor
Dial “VD-R” switch to ON
S702C
POWER
CCTV camera 1
S702C
S702C
Monitor
DOOR2
(Optional)
- GND
AF 1
1
GND 1
2
VCC 1
3
VD 1
4
Electronic lock
GND I/O
DAT I/O
Electronic lock
Electric lock power
GND 2
CCTV camera 1
VCC 2
AF I/O
GND I/O
The operation for monitor function,pls refer to the OPERATION 5.b
DAT I/O
VD-IN
CCTV camera 2
GND
CCTV camera 3
GND
VD-OUT
Monitor
GND
Remark: The monitor's “VD-R” switch should be dialed to “ON”.
Back view of the unit
VD I/O
CCTV1
4
VD-IN
VD-OUT
EXTENSION
AF I/O
CCTV2
3
VD 1
CCTV1
Electric lock power
VCC 2
VD 2
VD-OUT
VCC 1
CCTV2
DOOR2
AF 2
VD-IN
1
2
VD I/O
GND 2
VD-IN
AF 1
GND 1
VD 2
EXTENSION
DC13.5V/1.5A
(Optional)
- GND
AF 2
+ VCC
Outdoor camera
DOOR1
POWER
Dial “VD-R” switch to ON
+ VCC
DC13.5V/1.5A
Outdoor camera
DOOR1
CCTV camera 2
CCTV camera 1
GND
Connection diagram for more monitor and 2 outdoor camera
CCTV camera 2
GND
VD-OUT
GND
Monitor
S702C(Main monitor）
Remark: The monitor's “VD-R” switch should be dialed to “ON”.
S702C(Sub monitor 1)
S702C(Sub monitor N N≤3)
Back view of the unit
Connection diagram of indoor monitor and outdoor camera (1-2)
Electronic lock
CCTV camera 1
CCTV camera 2
Outdoor camera 1
Electronic lock
Electric lock power
S702C
Electronic lock
CCTV camera 3
CCTV camera 5
CCTV camera 4
CCTV camera 6
Electronic lock
Outdoor camera 1 Outdoor camera 2
Monitor
Monitor
Electric lock power
Electric lock power
Outdoor camera 2
Monitor
CCTV camera 1
AF I/O
Electric lock power
GND I/O
DAT I/O
VD-IN
GND
CCTV camera 1
AF I/O
GND I/O
DAT I/O
VD I/O
VD I/O
VD-IN
VD-OUT
GND
GND
Monitor
Remark: The monitor's “VD-R” switch should be dialed to “ON”.
POWER
DOOR1
GND 2
VCC 2
AF I/O
GND I/O
GND I/O
DAT I/O
DAT I/O
VD I/O
VD I/O
CCTV
camera 3
GND
GND
VD-OUT
GND
Dial “VD-R” switch
to ON
GND 2
VCC 2
VD 2
AF I/O
VD-IN
Remark: The last monitor's “VD-R” switch should be dialed to “ON”, other's keep “OFF”.
DOOR2
VD 1
AF 2
CCTV camera 2
Monitor
VCC 1
VD 1
CCTV camera 1
GND
GND 1
AF 2
VD-IN
GND
VD-OUT
AF I/O
DAT I/O
GND
Dial “VD-R” switch
to OFF
VD 2
GND I/O
Back view of the unit
CCTV camera 2
POWER
Electric lock power
(Optional)
AF 1
CCTV
camera 4
Monitor
EXTENSION
4
VD-IN
VD-OUT
CCTV1
VD-IN
CCTV2
VD I/O
VD 2
Electric lock power
Electronic lock
- GND
AF I/O
GND I/O
DAT I/O
VD I/O
CCTV1
4
Electronic lock
3
VCC 1
+ VCC
DC13.5V/1.5A
VD-IN
CCTV2
3
Electric lock power
2
VCC 2
(Optional)
VD-IN
VD-OUT
1
2
GND 2
GND 1
CCTV1
AF 2
GND 2
Electronic lock
1
- GND
CCTV2
4
DOOR2
3
VCC 1
EXTENSION
2
VCC 2
4
AF 2
Electronic lock
DOOR1
3
S702C(Sub monitor N N≤3)
+ VCC
DC13.5V/1.5A
AF 1
DOOR2
DOOR1
2
VCC 1
CCTV1
DOOR2
GND 1
CCTV2
POWER
DOOR1
1
GND 1
Outdoor camera
EXTENSION
1
Outdoor camera 2
AF 1
VD 2
VD-OUT
(Optional)
AF 1
VD 1
(Optional)
- GND
VD 1
Back view of the unit
- GND
+ VCC
DC13.5V/1.5A
Outdoor camera
dialed to “ON”.
Monitor
S702C
+ VCC
DC13.5V/1.5A
Outdoor camera 1
Dial “VD-R” switch to ON
S702C(Sub monitor 1)
S702C(Main monitor）
EXTENSION
Dial “VD-R” switch to OFF
POWER
CCTV camera 2
VD-OUT
Electric lock power
GND
GND
VD-OUT
GND
CCTV
camera 5
CCTV
camera 6
Monitor
Specifications and accessories
Installation instruction
Specifications
27.4mm
136mm
240mm
Accessories
Screw:+P4×25TP1
Input:AC110~240V,50Hz/60Hz
Expansion plug :φ6×30mm
Output：DC13.5V/1.5A
Power adaptor (optional)
4.After connection, pack up the wire, hang up the unit to the bracket.
(after hang up, power on the unit to test if the unit can work.)
Installation instruction
Installation attention
1.When you choose the place to install the unit, please pay attention to:
Keep sufficient space for ventilation and easy communication.
Keep sufficient space to adjust while installing.
84mm
Not put hot resource under the unit.
The socket outlet shall be installed near the equipment and shall be easily accessible.
2.Do not expose the unit to sunshine or rain:
Even if you do not use it, don't expose it to sunshine or rain.
6mm
3.Do not expose to intense light:
Spotlight may cause stain or striation in the screen.
4.Do not disassemble the unit by yourself:
1.Concealed wiring: fix the bracket on the connection box which already installed on the wall.
Open wiring: drill 2 holes which distance should be 8.4cm, insert 2 expansion plug, then fix
the bracket with screws.
Improper disassembly may damage the unit or cause electric shock.
5.Do not splash water on the unit:
Install the unit in dry place. In case that the unit gets wet, turn off the unit and contact your dealer.
6.Check the ambient temperature and humidity:
Avoid using the unit where the temperature is hotter or colder than specified, otherwise the internal parts may get affected. Special care is required to use
Peeling length:
the unit at high temperature and humidity.
7.In case of trouble:
If any trouble occurs while you are using the unit, turn off the power and contact your dealer to avoid worse problem or unpredictable accident.
8.About operation:
Keep the unit away from magnetic equipments such as microwave oven or big speaker. If the unit will not be used for a long time, please switch it off.
Please install this unit near the
power socket (the distance
should be less than 1.2m).
9.About clean:
Use soft cloth to clean the unit. Do not use any impregnant, such as alcohol, benzene. If you have any problem, please contact your dealer.
2.As the picture showing, pull out the wire out of bracket, then
peel the wire cover, see the peeling length on the picture.。
3.Connect the wire to each connection terminal, then check if the wire is fixed enough. (see the
wiring sequence on the picture)