1. pets
2. birds

Pile Feeder for Xerox® iGen4®
and Xerox® iGen® 150 Presses
Overview Brief
Multigraf Pile Feeder
Increase your productivity with a high-capacity pile feeder
when running large volumes of oversized and heavier stocks.
For shops that print long runs or multiple jobs using a handful
of oversized or heavier stocks, one way to increase productivity
is to reduce the time dedicated to keeping trays full. Graphic
arts shops and in-plants that predominantly run stocks that
are relatively heavy (200+ gsm) or oversized (larger than 20.5")
can take advantage of the higher capacity and ergonomic
convenience of a pile feeder. The pile feeder provides a single
tray with a 19.5" capacity, which, for example, is about 1,100
sheets of 18 point stock. This allows a Xerox® iGen 150 Press
to run over 20 minutes at 50 ppm without cycling down due to
an “out of paper” condition. To further increase productivity,
additional carts can be pre-loaded offline and rolled in when it’s
time to replenish a stock, taking under 2 minutes.
The DFA-enabled pile feeder from Multigraf enables enhanced
flexibility in feeding stocks. Media can be any sheet size and
range from 24 lb Bond to 24 point Board (90 to 480 gsm).
The pile feeder is attached to the left-most feeder module on
the Xerox® iGen4 Press or Xerox® iGen 150 Press. With the pile
feeder, customers still have full use of all trays in the feeder
module(s) and stock pulls can be made in any combination.
When the pile feeder is empty, the system will automatically
switch to a feeder module tray, which contains the same media,
for load-while-run efficiency.
Customers using the Thick Stock solution on the Xerox® iGen4
Press can use the pile feeder to feed large quantities of stocks
compared to the upper tray of the feeder module, which is
required for media greater than 18 point (350 gsm).
Multigraf Pile Feeder
Features
• Ergonomically friendly—supports easy loading of stocks,
especially compared to loading heavy or large format stocks
in the upper feeder module tray
• Requires less moving of reams and pallets, since an empty
cart can be moved to the location of the pallets
• Holds the equivalent number of XL and XXL sheets
(20.6"–26.0") as two feeder modules (upper feed trays)
• Vacuum sheet picking delivers high reliability
• Front airblow system ensures sheet separation to prevent
double feeding
• Registration table ensures the sheet is properly registered to
minimize jams in the press
Benefits
Paper Size (min/max)
• Increases machine utilization for more productive time in
your shop
• Operators spend less time loading stocks and have more time
for other tasks
• Does not reduce the number of available feeder trays and
can increase the number of pick points
• Additional carts (optional) can be used to preload the paper
outside of the machine for quick swapping of a full cart for
an empty cart
• Reduces the time spent reloading trays for shops with
tight production windows
Minimum
≤18 point (350 gsm)
>18 point (or > 350 gsm)
for a Xerox® iGen4® Press
with Thick Stock
8" x 8"
10" x 16.5"
Maximum 14.33" x 26"
14.3" x 24"
Paper Types
• Coated and uncoated
Paper Weights
• 24 lb Bond to 24 point Board (90–480 gsm)
(Subject to printer specifications)
Pile Height
• 19.5" maximum
Communication Protocol with a Xerox® iGen® Press
• DFA
Dimensions
Feeder unit including registration table
• Length 72.1"
• Width 29.4"
• Height 39.4"
Power Requirements
• 110 V/60 Hz
Add value for your customers and differentiate Xerox
from the competition with the Multigraf Pile Feeder.
For more information, contact your Xerox representative
or visit us at www.xerox.com.
©2014 Xerox Corporation. All rights reserved. Xerox®, Xerox and Design®, iGen® and iGen4® are trademarks
of Xerox Corporation in the United States and/or other countries. 10/14 CHENA171 BR11043 IG4SS-06UA
• 240 V/50 Hz