Download Report

Focus on high quality and best service
WATER PUMP
---------General Catalogue
Taizhou Leading Machinery Industry Co.,Ltd
QB electropumps with peripheral impeller
RANGEOFPERFORMANCE
CONSTRUCTION CHARACTERISTICS
Flow rate up to 50 l/min (3.0 m3/h)
Head up to 60 m
● PUMP BODY: cast iron.
● IMPELLER: brass, with radial peripheral vanes.
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: ceramic - graphite.
● ELECTRIC MOTOR: single-phase 230 V - 50 Hz
with condenser and thermal overload protector built
into the copper winding.
● INSULATION: class B.
● PROTECTION: IP 44.
LIMITS OF USE
Suction height up to 8 m
Liquid temperature up to + 40°C
Environment temperature up to + 40°C
USES AND INSTALLATIONS
They are recommended for pumping clean water
without abrasive particles,and liquids that are
chemically non aggressive for the materials of which
the pump is made. For their reliability, simplicity of
use and economy they are suitable for domestic use
and in particular for distributing water in combination
with small autoclaves, for irrigation gardens.
The pumps must be installed in enclosed places, or
at least protected against inclement weather.
Model
Power
GUARANTEE 1 YEAR
subject to our general terms of sale.
Volt. Freq. Q.Max. H.Max. Suct.Max.
Size
Dimension
G/W
Single-phase
kW
Hp
V
Hz
M3/h
M
M
Inch
(L×W×H)mm
Kg
QB50
0.125
0.17
220
50
1
18
8
1×1
235×115×140
3.9
QB60
0.37
0.5
220
50
1.6
33
8
1×1
280×140×170
5.5
QB70
0.55
0.75
220
50
2.4
48
8
1×1
335×190×210
8.5
QB80
0.75
1
220
50
3
60
8
1×1
340×190×210
9
CPm centrifugal electropumps
RANGEOFPERFORMANCE
CONSTRUCTION CHARACTERISTICS
Flow rate up to 160 l/min (9.6 m3/h)
Head up to 58 m
● PUMP BODY: cast iron.
● IMPELLER: brass or stainless steel..
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: ceramic - graphite.
● ELECTRIC MOTOR: CPm: single-phase 230 V 50 Hz with condenser and thermal overload protector
built into the copper winding. CP: threephase230/400 V - 50 Hz.
● INSULATION: class B.
● PROTECTION: IP 44.
LIMITS OF USE
Suction height up to 7 m
Liquid temperature up to + 40°C
Environment temperature up to + 40°C
USES AND INSTALLATIONS
They are recommended for pumping clean water
without abrasive particles,and liquids that are
chemically non aggressive for the materials of which
the pump is made. For their reliability, simplicity of
use and economy they are suitable for domestic use
and in particular for distributing water in combination
with small autoclaves, for irrigation gardens.
The pumps must be installed in enclosed places, or
at least protected against inclement weather.
Model
Power
GUARANTEE 1 YEAR
subject to our general terms of sale.
Q.Max.
H.Max.
Size
Suct.Max
.
Inch
M
Single-phase
Three-phase
kW
Hp
M3/h
M
CPm130
-
0.37
0.5
5.5
22
CPm146
-
0.55
0.75
6
26
CPm158
-
0.75
1
6.5
32
CPm170
CP170
1.1
1.5
7.2
44
CPm190
CP190
1.6
2.2
7.2
52
CPm200
CP200
2.2
3
8
59
×1
1 ×1
1 ×1
1.25×1
1 ×1
1 ×1
1
7
7
7
7
7
7
Dimension
× ×H)mm
285×185×230
340×210×265
340×210×265
390×240×290
390×260×320
455×280×340
(L W
N/W
Kg
9
12
13
19
23
30.5
CPm centrifugal electropumps
RANGEOFPERFORMANCE
CONSTRUCTION CHARACTERISTICS
Flow rate up to 220 l/min (13.2 m3/h)
Head up to 38 m
● PUMP BODY: cast iron.
● IMPELLER: brass .
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: sic - graphite.
● ELECTRIC MOTOR: CPm: single-phase 230 V 50 Hz with condenser and thermal overload protector
built into the copper winding. CP: threephase230/400 V - 50 Hz.
● INSULATION: class B.
● PROTECTION: IP 44.
LIMITS OF USE
Suction height up to 7 m
Liquid temperature up to + 40°C
Environment temperature up to + 40°C
USES AND INSTALLATIONS
They are recommended for pumping clean water
without abrasive particles,and liquids that are
chemically non aggressive for the materials of which
the pump is made. For their reliability, simplicity of
use and economy they are suitable for domestic use
and in particular for distributing water in combination
with small autoclaves, for irrigation gardens.
The pumps must be installed in enclosed places, or
at least protected against inclement weather.
Model
Power
GUARANTEE 1 YEAR
subject to our general terms of sale.
Q.Max.
H.Max.
Size
Suct.Max
.
Inch
M
Single-phase
Three-phase
kW
Hp
M3/h
M
CPm25/160B
CP25/160B
1.1
1.5
13.2
33
CPm40/160B
CP40/160B
1.1
1.5
13.2
33
CPm25/160A
CP25/160A
1.5
2.0
13.2
38
CPm40/160A
CP40/160A
1.5
2.0
13.2
38
×1
1.5×1.5
1.5×1
1.5×1.5
1.5
7
7
7
7
Dimension
× ×H)mm
383×233×278
383×233×278
383×233×278
383×233×278
(L W
N/W
Kg
20
20
21
21
GPm centrifugal electropumps
RANGEOFPERFORMANCE
CONSTRUCTION CHARACTERISTICS
Flow rate up to 450 l/min (27 m3/h)
Head up to 36 m
● PUMP BODY: cast iron.
● IMPELLER: brass.
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: ceramic - graphite.
● ELECTRIC MOTOR: CPm: single-phase 230 V 50 Hz with condenser and thermal overload protector
built into the copper winding. CP: threephase230/400 V - 50 Hz.
● INSULATION: class B.
● PROTECTION: IP 44.
LIMITS OF USE
Suction height up to 7 m
Liquid temperature up to + 40°C
Environment temperature up to + 40°C
USES AND INSTALLATIONS
They are recommended for pumping clean water
without abrasive particles,and liquids that are
chemically non aggressive for the materials of which
the pump is made. For their reliability, simplicity of
use and economy they are suitable for domestic use
and in particular for distributing water in combination
with small autoclaves, for irrigation gardens.
The pumps must be installed in enclosed places, or
at least protected against inclement weather.
Model
Power
GUARANTEE 1 YEAR
subject to our general terms of sale.
Q.Max.
H.Max.
Size
Suct.Max
.
M
Single-phase
Three-phase
kW
Hp
M3/h
M
Inch
GPm53
GP53
0.75
1.0
5.4
36
1
GPm60
GP60
1.1
1.5
23.4
25
GPm70
GP70
1.5
2.0
23.4
30
GPm80
GP80
2.2
3.0
27
34
×1
2 ×2
2 ×2
2 ×2
7
7
7
7
Dimension
× ×H)mm
350×225×290
403×245×310
403×245×310
440×242×295
(L W
N/W
Kg
19.0
21.2
23.6
29.8
GAm centrifugal electropumps with open impeller
RANGEOFPERFORMANCE
CONSTRUCTION CHARACTERISTICS
Flow rate up to 250 l/min (15 m3/h)
Head up to 20 m
● PUMP BODY: cast iron.
● PUMP BODY COVER: stainless steel
● IMPELLER: brass with open type.
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: ceramic - graphite.
● ELECTRIC MOTOR: GAm: single-phase 230 V 50 Hz with condenser and thermal overload protector
built into the copper winding. GA: threephase230/400 V - 50 Hz.
● INSULATION: class B.
● PROTECTION: IP 44.
LIMITS OF USE
Suction height up to 7 m
Liquid temperature up to + 40°C
Environment temperature up to + 40°C
USES AND INSTALLATIONS
They are recommended for pumping clean water
without abrasive particle and liquids that are
chemically non aggressive for the materials of which
the pump is made. The constructive solution of the
open impeller allows pumping of liquid relatively
loaded with impurities without risk of clogging the
impeller. For this characteristic the pumps in the Gam
serials are specifically used in industry, for the
transfer of water from canals, rivers, reservoirs, tank
etc.
The pumps must be installed in enclosed places, or
at least protected against inclement weather.
Model
Power
GUARANTEE 1 YEAR
subject to our general terms of sale.
Q.Max.
H.Max.
Size
Suct.Max
.
Inch
M
Single-phase
Three-phase
kW
Hp
M3/h
M
GAm 1B
GA 1B
0.55
0.75
15
16
GAm 1A
GA 1A
0.75
1.0
15
20
×1.5
1.5×1.5
1.5
7
7
Dimension
× ×H)mm
350×235×255
350×235×255
(L W
N/W
Kg
12.0
13.0
GHFm centrifugal electropumps
RANGEOFPERFORMANCE
LIMITS OF USE
Flow rate up to 250 l/min (15 m3/h)
Head up to 20 m
Suction height up to 7 m
Liquid temperature up to + 40°C
Environment temperature up to + 40°C
USES AND INSTALLATIONS
The GHFm serials is recommended for use in the
civil, agricultural and industrial field. The high yields
reached and the possibility of continuous duty make
its use advantages for irrigation with flowing and
sprinkling water, for drawing water from lakes, rivers,
wells, or for different industrial uses characterised by
the need to achieve considerable flow rates in
relation to not too high head.
The pumps must be installed in enclosed places, or
at least protected against inclement weather.
GUARANTEE 1 YEAR
CONSTRUCTION CHARACTERISTICS
● PUMP BODY: cast iron.
● IMPELLER: brass with centrifugal radial flow type.
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: ceramic - graphite.
● ELECTRIC MOTOR: GHFm: single-phase 230 V 50 Hz with condenser and thermal overload protector
built into the copper winding. GHF: threephase230/400 V - 50 Hz.
● INSULATION: class B.
● PROTECTION: IP 44.
subject to our general terms of sale.
Model
Single-phase
Power
Three-phase
Q.Max.
H.Max.
Size
Suct.Max
.
Inch
M
kW
Hp
M3/h
M
GHFm5C
GHF5C
0.55
0.75
24
12.5
GHFm5B
GHF5B
0.75
1.0
30
13.7
GHFm5A
GHF5A
1.1
1.5
36
14.5
GHFm5BM
GHF5BM
1.1
1.5
30
20.2
GHFm5AM
GHF5AM
1.5
2.0
30
22.5
GHFm6C
GHF6C
1.1
1.5
60
11.9
GHFm6B
GHF6B
1.5
2.0
66
14.7
GHFm6A
GHF6A
2.2
3.0
72
18.5
GHFm6CR
GHF6CR
1.1
1.5
60
11.9
GHFm6BR
GHF6BR
1.5
2.0
66
14.7
GHFm6AR
GHF6AR
2.2
3.0
72
18.5
GHFm7BR
GHF7BR
3.0
4.0
72
21.8
GHFm7AR
GHF7AR
4.0
5.5
72
18.8
×2
2 ×2
2 ×2
2 ×2
2 ×2
3 ×3
3 ×3
3 ×3
4 ×4
4 ×4
4 ×4
4 ×4
4 ×4
2
7
7
7
7
7
7
7
7
7
7
7
7
7
Dimension
× ×H)mm
362×220×285
362×220×285
362×220×285
417×252×296
417×252×296
445×279×355
445×279×355
518×278×345
445×279×355
445×279×355
518×278×345
518×278×345
600×340×440
(L W
N/W
Kg
14.5
15.5
16.0
20.5
22.0
28.0
29.0
38.0
29.0
30.0
40.0
41.0
85.0
GNFm centrifugal electropumps with flanged inlets
RANGEOFPERFORMANCE
CONSTRUCTION CHARACTERISTICS
Flow rate up to 2200 l/min (130 m3/h)
Head up to 22.5 m
● PUMP BODY: cast iron.
● IMPELLER: brass with centrifugal radial flow type.
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: ceramic - graphite.
● ELECTRIC MOTOR: GNFm: single-phase 230 V 50 Hz with condenser and thermal overload protector
built into the copper winding. GNF: threephase230/400 V - 50 Hz.
● INSULATION: class B.
● PROTECTION: IP 44.
LIMITS OF USE
Suction height up to 7 m
Liquid temperature up to + 40°C
Environment temperature up to + 40°C
USES AND INSTALLATIONS
The GNFm serials, from the points of view of both
performance and mechanical dimensions, has been
expressly designed for use in the civil, agricultural
and industrial field. The high yields reached and the
possibility of continuous duty recommend its use for
irrigation with flowing and sprinkling water, for
drawing water from lakes, rivers, wells, and for
transfer in general.
The pumps must be installed in enclosed places, or
at least protected against inclement weather.
Model
Single-phase
Power
Three-phase
GUARANTEE 1 YEAR
subject to our general terms of sale.
Q.Max.
H.Max.
Size
Suct.Max
.
Inch
M
2
7
kW
Hp
M3/h
M
GNFm 129B
GNF 129B
1.1
1.5
30
20.2
GNFm 129BM
GNF 129BM
1.1
1.5
30
20.2
GNFm 129A
GNF 129A
1.5
2.0
30
22.5
GNFm 129AM
GNF 129AM
1.5
2.0
30
22.5
GNFm 130C
GNF 130C
1.1
1.5
60
11.9
GNFm 130B
GNF 130B
1.5
2.0
66
14.7
GNFm 130A
GNF 130A
2.2
3.0
72
18.5
GNFm 131B
GNF 131B
3.7
5.0
130
18.8
×2
2.5×2.5
2 ×2
2.5×2.5
3 ×3
3 ×3
3 ×3
4 ×4
7
7
7
7
7
7
7
Dimension
× ×H)mm
427×275×320
427×275×320
427×275×320
427×275×320
460×272×355
460×272×355
520×295×375
600×340×440
(L W
N/W
Kg
20.5
20.5
22.5
22.5
28.0
29.0
39.0
85.0
GFm centrifugal electropumps according to EN 733 - DIN 24255
RANGEOFPERFORMANCE
CONSTRUCTION CHARACTERISTICS
Flow rate up to 4200 l/min (250 m3/h)
Head up to 90 m
● PUMP BODY: cast iron, dimensions according to
standards EN 733- DIN 24255 and UNI 7467-NF E44-111, with flanged suction and delivery inlets and
threaded steel counter flanges.
● IMPELLER: brass or cast iron.
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: ceramic - graphite.
● ELECTRIC MOTOR: GFm: single-phase 230 V 50 Hz with condenser and thermal overload protector
built into the copper winding. GF: threephase230/400 V - 50 Hz.
● INSULATION: class B.
● PROTECTION: IP 55.
LIMITS OF USE
Suction height up to 7 m
Liquid temperature up to + 80°C
Environment temperature up to + 40°C
USES AND INSTALLATIONS
This series is indicated for supplying and moving
water, in cooling, heating, circulating and conditioning
systems, for fire fighting, irrigation, in the civil,
industrial and agricultural field. The realisation
according to standard EN733-DIN24255 ensures that
the dimensions comply with those standards. The
constructive form allows the pump body to be moved
without disconnecting it from the pipes.
The pumps must be installed in enclosed places, or
at least protected against inclement weather.
Current
3*380V
Power
TYPE
GUARANTEE 1 YEAR
subject to our general terms of sale.
CAPACITY(m³/h-l/min)
0
4.5
6
7.5
9
12
15
18
24
30
36
0
75
100
125
150
200
250
300
400
500
600
Hp
kW
GF50-32-160C
2
1.5
4
GF50-32-160B
3
2.2
5.2
26.0
GF50-32-160A
4
3
7.2
36.7
36.5 36.0 35.5 34.3 32.9 31.1 26.0
GF50-32-200C
5.5
4
9.3
41.0
40.0 39.6 38.8 37.5 36.0 34.2 30.0
GF50-32-200B
7.5
5.5
14.1
53.0
52.0 51.5 51.0 50.0 48.5 46.8 42.6 37.0 28.8
GF50-32-200A
10
7.5
16.5
61.0
60.5 60.0 59.5 58.5 57.2 55.5 51.5 46.3 38.4
GF50-32-250C
12
9
20
70.0
68.5 68.0 67.0 65.6 63.5 58.7 50.5
GF50-32-250B
15
11
24.2
82.0
81.0 80.5 79.5 78.5 77.0 72.6 66.5
GF50-32-250A
20
15
30
93.0
92.4 92.0 91.5 90.5 89.4 85.6 80.0
20.3 19.6 19.1 18.2 16.8 15.5 14.1 12.3
25
24.6 24.1 23.2 22.0 20.5 18.8
GFm centrifugal electropumps according to EN 733 - DIN 24255
Current
3*380V
Power
TYPE
CAPACITY(m³/h-l/min)
0
15
18
24
30
36
42
48
60
72
78
0
250
300
400
500
600
700
800 1000 1200 1300
6.0
Hp
kW
GF65-40-125B
2
1.5
4
18.1
17.2 16.7
15.0 12.7
9.6
GF65-40-125A
3
2.2
5.2
24.4
23.5 23.0
21.0 18.8
15.8 12.3
GF65-40-160C
4
3
7.2
26.1
26.0
25.5 24.0
22.5 19.0
15.0
GF65-40-160B
5.5
4
7.3
30.0
29.5
29.0 28.0
27.0 23.5
20.0
GF65-40-160A
5.5
5.5
10
35.3
34.5
33.5 33.0
33.5 29.0
25.0
GF65-40-200B
7.5
5.5
13.1
46.6
45.0 44.0
41.0 38.5
34.5 29.5
GF65-40-200A
10
7.5
16.7
57.0
55.0 54.0
52.0 49.0
45.5 41.4
36.0
GF65-40-250C
15
11
24.3
64.0
60.0 59.0
56.0 53.0
49.0 45.0
39.0
GF65-40-250B
20
15
32
72.0
68.0 67.0
65.0 61.0
57.0 52.0
47.0
GF65-40-250A
25
18.5
41.5
85.0
81.0 80.0
77.0 74.0
70.0 65.0
60.0
GF65-50-125B
4
3
7.2
20.0
19.5
18.8 18.0
16.9 14.1
10.5
GF65-50-125A
5.5
4
9.9
24.0
23.5
23.0 22.5
21.5 19.0
15.8 11.8
GF65-50-160B
7.5
5.5
11.7
32.0
31.5
30.5 29.5
28.0 24.5
20.5 14.8
GF65-50-160A
10
7.5
15.8
40.0
39.0
38.0 37.0
36.0 33.0
29.0 24.0
GF65-50-200C
12
9
18.5
47.0
43.3
42.9 40.2
38.5 33.0
24.5
GF65-50-200B
15
11
21
52.0
45.7 50.0
48.5 46.8
44.7 39.4
32.0
GF65-50-200A
20
15
27
58.6
51.0 57.6
56.4 55.0
53.3 49.0
42.9 38.8
GF65-50-250C
20
15
32.5
71.4
58.1 70.2
69.0 67.5
66.0 61.5
55.0 50.5
GF65-50-250B
25
18.5
41.5
78.0
77.5
76.1 74.5
72.9 68.3
62.3 58.3
GF65-50-250A
30
22.5
51.6
90.0
88.8
87.7 86.1
84.6 80.5
75.3 71.8
GFm centrifugal electropumps according to EN 733 - DIN 24255
Current
3*380V
Power
TYPE
CAPACITY(m³/h-l/min)
0
48
60
72
78
84
96 108 120 132 144 156 168 180 195 210 225 250
0
800
100 120 130 140 160 180 200 220 240 260 280 300 325 350 370 416
0
0
0
0
0
0
0
0
0
0
0
0
0
7
0
0
Hp
kW
GF80-65-125B
7.5
5.5
12.3
23.0 21.5 20.5 19.0 18.3 17.5 16.0 14.0
GF80-65-125A
10
7.5
16
27.0 26.0 25.0 24.5 23.0 22.0 20.0 18.0
GF80-65-160C
12
9
19.4
30.5 31.2 30.5 29.7 29.0 28.3 26.5 24.6 22.1 19.4 16.0
GF80-65-160B
15
11
22.3
36.0 34.5 34.0 33.0 32.8 31.5 30.0 28.0 25.5 24.1 21.1
GF80-65-160A
20
15
30
GF80-65-200C
20
15
32.5
45.0
44.6 43.7 43.0 42.3 40.5 38.0 35.3 32.0
GF80-65-200B
25
18.5
41.5
52.0
49.3 48.5 48.0 47.3 45.5 43.5 41.0 38.0
GF80-65-200A
30
22
51.3
59.0
56.5 55.7 55.2 54.8 53.3 51.5 49.0 47.2 44.0
GF80-65-250B
40
30
63.4
81.0
78.5 76.0 74.6 73.0 69.3 65.0 60.0 54.6 48.6
GF80-65-250A
50
37
74.3
90.0
88.5 86.5 85.4 84.0 80.5 76.4 72.0 66.7 60.5 54.0
GF100-80-160D
15
11
20.8
26.0
25.4 25.1 24.7 23.9 22.9 21.8 20.0 19.3 17.8 16.4 14.6
GF100-80-160C
20
15
25.8
29.5
29.2 29.0 28.7 28.2 27.0 25.9 24.7 23.4 22.0 20.5 18.7 16.5
GF100-80-160B
25
18.5
35
34.5
33.9 33.7 33.4 37.7 32.0 31.0 30.0 29.0 27.7 26.4 25.0 22.9 20.4
GF100-80-160A
30
22
42
39.0
38.0 37.8 37.3 36.9 36.2 35.5 34.5 33.6 32.4 31.3 30.0 28.0 25.7 22.9
GF100-80-200B
30
22
42
44.0
43.5 43.2 42.8 42.5 42.0 41.5 40.0 37.8 36.5 35.0 30.5 26.5
GF100-80-200A
40
30
63.4
57.0
56.5 56.2 56.0 55.5 55.0 53.8 52.5 51.8 50.0 48.0 45.5 41.0 38.5
GF125-100-200C
30
22
42
38.0
36.8 36.5 36.0 35.5 34.5 34.0 33.5 32.5 31.5 30.0 27.5
GF125-100-200B
40
30
63.4
43.0
42.0 41.8 41.5 41.0 40.5 40.0 39.5 38.0 37.0 36.0 34.0
GF125-100-200A
50
37
74.3
48.0
47.6 47.4 47.2 47.0 46.5 46.4 45.5 44.5 43.5 42.5 40.0
42.0 41.5 41.0 40.0 39.4 38.5 37.0 35.0 33.0 30.0
2GPm twin-impeller
impeller centrifugal electropumps
RANGEOFPERFORMANCE
CONSTRUCTION CHARACTERISTICS
Flow rate up to 200 l/min (12 m3/h)
Head up to 70 m
● PUMP BODY: cast iron.
● IMPELLER: brass with centrifugal radial flow type.
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: ceramic - graphite.
● ELECTRIC MOTOR: 2GPm: single-phase 230 V 50 Hz with condenser and thermal overload protector
built into the copper winding. 2GP: threephase230/400 V - 50 Hz.
● INSULATION: class B.
● PROTECTION: IP 44.
LIMITS OF USE
Suction height up to 7 m
Liquid temperature up to + 40°C
Environment temperature up to + 40°C
USES AND INSTALLATIONS
They are recommended for pumping clean water and
liquids that are chemically non aggressive for the
materials of which the pump is made.
The high head and adaptability to the most varied,
even unusual applications, make them the ideal
choice in the domestic, civil and industrial field; in
particular for distributing water in combination with
autoclaves, for increasing pressure in the mains, for
fire-fighting sets.
The pumps must be installed in enclosed places, or
at least protected against inclement weather.
Model
Single-phase
Power
Three-phase
GUARANTEE 1 YEAR
subject to our general terms of sale.
Q.Max.
H.Max.
Size
Suct.Max
.
Inch
M
kW
Hp
M3/h
M
2GPm 25/130
2GP 25/130
0.75
1.0
4.8
44
2GPm 25/140H
2GP 25/140H
1.1
1.5
6..0
54
2GPm 25/140M
2GP 25/140M
1.1
1.5
8.4
47
2GPm 160/160
2GP 160/160
1.5
2.0
6.6
66
2GPm 25/160B
2GP 25/160B
1.5
2.0
9.6
58
2GPm 25/160A
2GP 25/160A
2.2
3.0
10.8
68
2GPm 32/200C
2GP 32/200C
3.0
4.0
12.0
70
2GPm 50/160B
2GP 50/160B
1.5
2.0
9.0
45
2GPm 50/160A
2GP 50/160A
2.2
3.0
11.1
58
×1
1.25×1
1.5×1
1.25×1
1.25×1
1.5×1
1.5×1.25
1.5×1.5
1.5×1.5
1.25
7
7
7
7
7
7
7
7
7
Dimension
× ×H)mm
370×225×260
410×242×280
410×242×280
435×250×305
435×250×305
518×278×345
518×278×345
450×260×330
450×260×330
(L W
N/W
Kg
15
20.5
20.5
25
25
27
40
38
40
3-4GPm multistage centrifugal electropumps
RANGEOFPERFORMANCE
CONSTRUCTION CHARACTERISTICS
Flow rate up to 90 l/min (5.4 m3/h)
Head up to 46 m
● PUMP BODY: cast iron.
● PUMP BODY COVER: stainless steel
● IMPELLER: noryl with centrifugal radial flow type.
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: ceramic - graphite.
● ELECTRIC MOTOR: 3-4GPm: single-phase 230 V
- 50 Hz with condenser and thermal overload
protector built into the copper winding. 3-4GP: threephase230/400 V - 50 Hz.
● INSULATION: class B.
● PROTECTION: IP 44.
LIMITS OF USE
Suction height up to 7 m
Liquid temperature up to + 40°C
Environment temperature up to + 40°C
USES AND INSTALLATIONS
They are recommended for pumping clean water and
liquids that are chemically non aggressive for the
materials of which the pump is made.
For the reliability, silence and absence of
maintenance, they are widely used in the domestic
place and in particular for distributing water in
combination with small or medium autoclaves, for
irrigating gardens, etc.
The pumps must be installed in enclosed places, or
at least protected against inclement weather.
Model
Power
GUARANTEE 1 YEAR
subject to our general terms of sale.
Q.Max.
H.Max.
Size
Suct.Max
.
M
Single-phase
Three-phase
kW
Hp
M3/h
M
Inch
3GPm 80
3GP 80
0.45
0.6
4.5
38
1
4GPm 80
4GP 80
0.60
0.8
5.4
46
×1
1 ×1
7
7
Dimension
× ×H)mm
385×186×190
405×190×205
(L W
N/W
Kg
11.6
15.2
AWZB automatic self-priming
priming electropumps
RANGEOFPERFORMANCE
USES AND INSTALLATIONS
Flow rate up to 75 l/min (4.5 m3/h)
Head up to 50 m
They are recommended for pumping clean water and
liquids that are chemically non aggressive for the
materials of which the pump is made. Reliable,
compact, economical and simple to use, they are
particularly suitable for domestic and industrial
applications such as water supply for recirculation in
air conditioners and refrigerators, industrial water
uses in general, and the automatic distribution of
water from surge tank, watering gardens, lifting water
from tanks or wells down to 9 meter depth. The pump
is supplied with a check valve on the suction side so
that no foot valve is required. The pumps must be
installed in enclosed places.
LIMITS OF USE
Suction height up to 9 m
Liquid temperature up to + 100°C
Environment temperature up to + 40°C
CONSTRUCTION CHARACTERISTICS
● PUMP BODY: cast iron.
● IMPELLER: brass.
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: ceramic – graphite.
● INSULATION: class B.
● PROTECTION: IP 44.
GUARANTEE 1 YEAR
subject to our general terms of sale.
Model
Power
Q.Max.
H.Max.
Size
Suct.Max
.
Inch
M
1
9
kW
Hp
M3/h
M
25AWZB125
0.125
0.17
1.8
24
25AWZB250
0.25
0.34
2.0
28
25AWZB370
0.37
0.5
2.2
32
25AWZB550
0.55
0.75
2.8
38
25AWZB750
0.75
1.0
3.0
44
38AWZB1100
1.1
1.5
4.5
50
Single-phase
Three-phase
×1
1 ×1
1 ×1
1 ×1
1 ×1
1.5×1.5
9
9
9
9
9
Dimension
× ×H)mm
280×225×305
280×225×305
280×225×305
310×235×330
345×250×335
360×280×370
(L W
N/W
Kg
9
10
11
13
14.5
18.5
AWZB-S automatic self-priming
priming INVERTER pumps
RANGEOFPERFORMANCE
USES AND INSTALLATIONS
Flow rate up to 75 l/min (4.5 m3/h)
Head up to 50 m
They are recommended for pumping clean water and
liquids that are chemically non aggressive for the
materials of which the pump is made. Reliable,
compact, economical and simple to use, they are
particularly suitable for domestic and industrial
applications such as water supply for recirculation in
air conditioners and refrigerators, industrial water
uses in general, and the automatic distribution of
water from surge tank, watering gardens, lifting water
from tanks or wells down to 9 meter depth. The pump
is supplied with a check valve on the suction side so
that no foot valve is required. The pumps must be
installed in enclosed places.
LIMITS OF USE
Suction height up to 9 m
Liquid temperature up to + 100°C
Environment temperature up to + 40°C
CONSTRUCTION CHARACTERISTICS
● PUMP BODY: cast iron.
● IMPELLER: brass.
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: ceramic – graphite.
● INSULATION: class B.
● PROTECTION: IP 44.
GUARANTEE 1 YEAR
subject to our general terms of sale.
Model
Power
Q.Max.
H.Max.
Size
Suct.Max
.
Inch
M
1
9
kW
Hp
M3/h
M
25AWZB125S
0.125
0.17
1.8
24
25AWZB250S
0.25
0.34
2.0
28
25AWZB370S
0.37
0.5
2.2
32
25AWZB550S
0.55
0.75
2.8
38
25AWZB750S
0.75
1.0
3.0
44
Single-phase
Three-phase
×1
1 ×1
1 ×1
1 ×1
1 ×1
9
9
9
9
Dimension
× ×H)mm
280×225×305
280×225×305
280×225×305
310×235×330
345×250×335
(L W
N/W
Kg
9
10
11
13
14.5
WZB self-priming electropumps
RANGEOFPERFORMANCE
USES AND INSTALLATIONS
Flow rate up to 60 l/min (3.5 m3/h)
Head up to 50 m
They are recommended for pumping clean water and
liquids that are chemically non aggressive for the
materials of which the pump is made. Reliable,
compact, economical and simple to use, they are
particularly suitable for domestic and industrial
applications such as water supply for recirculation in
air conditioners and refrigerators, industrial water
uses in general, and the automatic distribution of
water from surge tank, watering gardens, lifting water
from tanks or wells down to 9 meter depth. The pump
is supplied with a check valve on the suction side so
that no foot valve is required. The pumps must be
installed in enclosed places.
LIMITS OF USE
Suction height up to 9 m
Liquid temperature up to + 40°C
Environment temperature up to + 40°C
CONSTRUCTION CHARACTERISTICS
● PUMP BODY: cast iron.
● IMPELLER: brass.
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: ceramic – graphite.
● INSULATION: class B.
● PROTECTION: IP 44.
GUARANTEE 1 YEAR
subject to our general terms of sale.
Model
Power
Q.Max.
H.Max.
Size
Suct.Max
.
Inch
M
1
9
kW
Hp
M3/h
M
25WZB35
0.37
0.5
2.0
30
25WZB45
0.60
0.8
2.5
40
25WZB65
0.75
1.0
3.5
50
Single-phase
Three-phase
×1
1 ×1
1 ×1
9
9
Dimension
× ×H)mm
290×200×250
310×210×270
310×210×270
(L W
N/W
Kg
8.0
10
12
GKSm automatic self-priming
priming electropumps
RANGEOFPERFORMANCE
USES AND INSTALLATIONS
Flow rate up to 40 l/min (2.4 m3/h)
Head up to 32 m
They are recommended for pumping clean water and
liquids that are chemically non aggressive for the
materials of which the pump is made. Reliable,
compact, economical and simple to use, they are
particularly suitable for domestic and industrial
applications such as water supply for recirculation in
air conditioners and refrigerators, industrial water
uses in general, and the automatic distribution of
water from surge tank, watering gardens, lifting water
from tanks or wells down to 9 meter depth. The pump
is supplied with a check valve on the suction side so
that no foot valve is required. The pumps must be
installed in enclosed places.
LIMITS OF USE
Suction height up to 9 m
Liquid temperature up to + 100°C
Environment temperature up to + 40°C
CONSTRUCTION CHARACTERISTICS
● PUMP BODY: cast iron, with copper cover.
● IMPELLER: brass.
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: ceramic – graphite.
● INSULATION: class B.
● PROTECTION: IP 44.
GUARANTEE 1 YEAR
subject to our general terms of sale.
Model
Single-phase
GKSm130
Power
Three-phase
Q.Max.
H.Max.
Size
Suct.Max
.
kW
Hp
M3/h
M
Inch
M
0.125
0.17
2.4
32
1
×1
9
Dimension
× ×H)mm
280×225×305
(L W
N/W
Kg
9
GSWm “JET” self-priming
priming electropumps
RANGEOFPERFORMANCE
USES AND INSTALLATIONS
Flow rate up to 80 l/min (4.8 m3/h)
Head up to 72 m
They are recommended for pumping clean water and
liquids that are chemically non aggressive for the
materials of which the pump is made. This serial selfpriming Jet pumps are designed for sucking up water
even in the presence of air mixed with the pumped
liquid. For their reliability and absence of
maintenance, they are recommended for domestic
use, especially for distributing water in combination
with small or medium autoclaves, for irrigation
gardens, etc.
The pumps must be installed in enclosed places or at
least protected against inclement weather.
LIMITS OF USE
Suction height up to 9 m
Liquid temperature up to + 40°C
Environment temperature up to + 40°C
CONSTRUCTION CHARACTERISTICS
● PUMP BODY: cast iron
● PUMP BODY COVER: stainless steel
● IMPELLER: brass.
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: ceramic – graphite.
● ELECTRIC MOTOR:
GSWm: single-phase 230 V- 50 Hz with condenser
and thermal overload protector built into the winding
GSW: three-phase 230/400 V - 50 Hz.
● INSULATION: class B.
● PROTECTION: IP 44.
Model
Power
GUARANTEE 1 YEAR
subject to our general terms of sale.
Q.Max.
H.Max.
Size
Suct.Max
.
Inch
M
1
9
Single-phase
Three-phase
kW
Hp
M3/h
M
GSWm 1C
GSW 1C
0.37
0.50
3.0
35
GSWm 1B
GSW 1B
0.55
0.75
3.0
41
GSWm 10M
GSW 10M
0.75
1.0
4.8
46
GSWm 15M
GSW 15M
1.10
1.5
4.8
55
GSWm10H
GSW10H
0.75
1.0
3.0
56
GSWm 15H
GSW 15H
1.10
1.5
3.0
72
×1
1 ×1
1 ×1
1 ×1
1 ×1
1 ×1
9
9
9
9
9
Dimension
× ×H)mm
395×186×214
395×186×214
438×196×235
438×196×235
438×196×235
438×196×235
(L W
N/W
Kg
9.5
10.5
15.0
15.5
15.0
15.5
GSWm “JET” self-priming
priming electropumps
RANGEOFPERFORMANCE
USES AND INSTALLATIONS
Flow rate up to 160 l/min (9.6 m3/h)
Head up to 76 m
They are recommended for pumping clean water and
liquids that are chemically non aggressive for the
materials of which the pump is made. This serial selfpriming Jet pumps are designed for sucking up water
even in the presence of air mixed with the pumped
liquid. For their reliability and absence of
maintenance, they are recommended for domestic
use, especially for distributing water in combination
with small or medium autoclaves, for irrigation
gardens, etc.
The pumps must be installed in enclosed places or at
least protected against inclement weather.
LIMITS OF USE
Suction height up to 9 m
Liquid temperature up to + 40°C
Environment temperature up to + 40°C
CONSTRUCTION CHARACTERISTICS
● PUMP BODY: cast iron
● PUMP BODY COVER: cast iron
● IMPELLER: brass.
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: ceramic – graphite.
● ELECTRIC MOTOR:
GSWm: single-phase 230 V- 50 Hz with condenser
and thermal overload protector built into the winding
GSW: three-phase 230/400 V - 50 Hz.
● INSULATION: class B.
● PROTECTION: IP 44.
Model
Power
GUARANTEE 1 YEAR
subject to our general terms of sale.
Q.Max.
H.Max.
Size
Suct.Max
.
Inch
M
Single-phase
Three-phase
kW
Hp
M3/h
M
GSWm 3CH
GSW 3CH
1.1
1.5
4.2
64
GSWm 3BH
GSW 3BH
1.5
2.0
4.8
76
GSWm 3CM
GSW 3CM
1.1
1.5
7.2
52
GSWm 3BM
GSW 3BM
1.5
2.0
7.2
60
GSWm 3CL
GSW 3CL
1.1
1.5
9.6
42
GSWm 3BL
GSW 3BL
1.5
2.0
9.6
51
×1
1.25×1
1.25×1
1.25×1
1.25×1
1.25×1
1.25
9
9
9
9
9
9
Dimension
× ×H)mm
573×238×270
573×238×270
573×238×270
573×238×270
573×238×270
573×238×270
(L W
N/W
Kg
24
25
24
25
24
25
GSLm “JET” self-priming electropumps
RANGEOFPERFORMANCE
USES AND INSTALLATIONS
Flow rate up to 60 l/min (3.6 m3/h)
Head up to 45 m
They are recommended for pumping clean water and
liquids that are chemically non aggressive for the
materials of which the pump is made. This serial selfpriming Jet pumps are designed for sucking up water
even in the presence of air mixed with the pumped
liquid. For their reliability and absence of
maintenance, they are recommended for domestic
use, especially for distributing water in combination
with small or medium autoclaves, for irrigation
gardens, etc.
The pumps must be installed in enclosed places or at
least protected against inclement weather.
LIMITS OF USE
Suction height up to 9 m
Liquid temperature up to + 40°C
Environment temperature up to + 40°C
CONSTRUCTION CHARACTERISTICS
● PUMP BODY: cast iron
● PUMP BODY COVER: stainless steel or cast iron
● IMPELLER: brass.
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: ceramic – graphite.
● ELECTRIC MOTOR:
GSLm: single-phase 230 V- 50 Hz with condenser
and thermal overload protector built into the winding
GSL: three-phase 230/400 V - 50 Hz.
● INSULATION: class B.
● PROTECTION: IP 44.
Model
Power
GUARANTEE 1 YEAR
subject to our general terms of sale.
Q.Max.
H.Max.
Size
Suct.Max
.
Inch
M
1
9
Single-phase
Three-phase
kW
Hp
M3/h
M
GSLm 60
GSL 60
0.37
0.50
2.1
38
GSLm 80
GSL 80
0.55
0.75
2.4
42
GSLm 100
GSL 100
0.75
1.0
3.6
45
×1
1 ×1
1 ×1
9
9
Dimension
× ×H)mm
467×198×232
475×190×220
475×190×220
(L W
N/W
Kg
12
14
15
GJSm “JET” self-priming electropumps with s.s pump body
RANGEOFPERFORMANCE
USES AND INSTALLATIONS
Flow rate up to 60 l/min (3.6 m3/h)
Head up to 45 m
They are recommended for pumping clean water and
liquids that are chemically non aggressive for the
materials of which the pump is made. This serial selfpriming Jet pumps are designed for sucking up water
even in the presence of air mixed with the pumped
liquid. For their reliability and absence of
maintenance, they are recommended for domestic
use, especially for distributing water in combination
with small or medium autoclaves, for irrigation
gardens, etc.
The pumps must be installed in enclosed places or at
least protected against inclement weather.
LIMITS OF USE
Suction height up to 9 m
Liquid temperature up to + 40°C
Environment temperature up to + 40°C
CONSTRUCTION CHARACTERISTICS
● PUMP BODY: stainless steel
● PUMP BODY COVER: stainless steel or cast iron
● IMPELLER: brass.or PPO
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: ceramic – graphite.
● ELECTRIC MOTOR:
GJSm: single-phase 230 V- 50 Hz with condenser
and thermal overload protector built into the winding
GJS: three-phase 230/400 V - 50 Hz.
● INSULATION: class B.
● PROTECTION: IP 44.
Model
Power
GUARANTEE 1 YEAR
subject to our general terms of sale.
Q.Max.
H.Max.
Size
Suct.Max
.
Inch
M
1
9
Single-phase
Three-phase
kW
Hp
M3/h
M
GJSm 400
GJS 400
0.4
0.5
2.4
28
GJSm 600
GJS 600
0.6
0.8
2.4
35
GJSm 800
GJS 800
0.8
1.1
3.0
42
GJSm 1100
GJS 1100
1.1
1.5
3.6
45
×1
1 ×1
1 ×1
1 ×1
9
9
9
Dimension
× ×H)mm
350×195×215
350×195×215
410×210×240
410×210×240
(L W
N/W
Kg
6.0
6.4
9.0
9.7
GDPm “JET” self-priming electropumps for deep well
USES AND INSTALLATIONS
RANGEOFPERFORMANCE
These pumps are suitable for pumping clean water and
fluids which are not chemically aggressive to the pump
components. This serial pump installed above ground
with the jet body submerged guarantees functioning
LIMITS OF USE
even when the static level of the well water falls as far
Suction height up to 50 m
as 50 meters below the level of the installed pump. For
Liquid temperature up to + 40°C
this reason these pumps are extremely reliable,
Environment temperature up to + 40°C
economical and simple to use and find many uses in
domestic applications and the automatic distribution of
CONSTRUCTION CHARACTERISTICS
water from small and medium sized surge tanks,
● PUMP BODY: stainless steel
watering gardens, etc. In all cases where the suction
● EJECTOR: cast iron
depth exceeds the normal capacity (9m) for surface
● IMPELLER: brass.
pumps. Always install a retention valve on the jet body
● MOTOR SHAFT: 45# steel or stainless steel
opening. It is advisable to install a valve on the pump
● MECHANICAL SEAL: ceramic – graphite.
● ELECTRIC MOTOR: with condenser and thermal delivery opening, to ensure adequate counter pressure
when working. Fill the pump body and piping
overload protector built into the winding
connection the pump to the jet body with water before
● INSULATION: class B.
starting up. When drawing water from depths not
● PROTECTION: IP 44.
exceeding 9meters the jet body can be installed directly
onto the pump body. In this case, when first starting up
GUARANTEE 1 YEAR
fill the pump body with water, without bothering to fill
subject to our general terms of sale.
the suction piping.
The pumps must be installed in enclosed places or at
least protected against inclement weather.
Flow rate up to 30 l/min (1.9 m3/h)
Head up to 45 m
Model
Power
Q.Max.
H.Max.
Size
Suct.Max
.
Inch
M
kW
Hp
M3/h
M
GDPm 255
0.55
0.75
1.7
46
GDPm 370
0.75
1.0
1.7
48
GDPm 505
1.10
1.5
1.9
82
GDPm 750
1.50
2.0
1.9
100
Single-phase
Three-phase
×1 ×1
1.25×1×1
1.25×1×1
1.25×1×1
1.25
25
25
35
45
Dimension
× ×H)mm
423×288×245
423×288×245
525×235×295
525×235×295
(L W
N/W
Kg
16
19
32
34
GDWm “JET” self-priming
priming electropumps for deep well
RANGEOFPERFORMANCE
CONSTRUCTION CHARACTERISTICS
Flow rate up to 60 l/min (3.6 m3/h)
Head up to 45 m
● PUMP BODY: cast iron
● EJECTOR: cast iron
● IMPELLER: brass.
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: ceramic – graphite.
● ELECTRIC MOTOR: with condenser and thermal
overload protector built into the winding for singe
phase.
● INSULATION: class B.
● PROTECTION: IP 44.
LIMITS OF USE
Suction height up to 45 m
Liquid temperature up to + 40°C
Environment temperature up to + 40°C
USES AND INSTALLATIONS
These pumps are suitable for pumping clean water
and fluids which are not chemically aggressive to the
pump components. This serial pump installed above
ground with the jet body submerged guarantees
functioning even when the static level of the well
water falls as far as 45 meters below the level of the
installed pump. For this reason these pumps are
extremely reliable, economical and simple to use and
find many uses in domestic applications and the
automatic distribution of water from small and
medium sized surge tanks, watering gardens, etc. In
all cases where the suction depth exceeds the
normal capacity (9m) for surface pumps. Always
install a retention valve on the jet body opening. It is
advisable to install a valve on the pump delivery
opening, to ensure adequate counter pressure when
working. Fill the pump body and piping connection
the pump to the jet body with water before starting up.
When drawing water from depths not exceeding
9meters the jet body can be installed directly onto the
pump body. In this case, when first starting up fill the
pump body with water, without bothering to fill the
suction piping.
The pumps must be installed in enclosed places or at
least protected against inclement weather.
GUARANTEE 1 YEAR
subject to our general terms of sale.
WORKING PRINCIPLE
This series are self-priming centrifugal pumps
suitable for suction from deep wells. Self-priming is
achieved using an ejector, housed in the jet body,
which can be installed directly on the pump body or
more often lowered in a well and connected to the
pump body by two pipes. The total delivery produced
by the closed centrifugal impeller is sent only partly
to the delivery opening. The remaining water is
recirculated the pump by two pipes. The total delivery
suction chamber where it generates the necessary
vacuum to the delivery opening. The remaining water
is recirculted through the ejector, which is connected
to the diffuser with recirculating water form the pump,
thus increasing its pressure at the expense of the
recirculating water, and is drawn into the pump
through the suction pipe. When the jet body is
directly installed on the pump body this pump works
like the GDPm serial pumps.
GDWm
“JET” self-priming
priming electropumps for 2” well
RANGEOFPERFORMANCE
Suction lift down to 35 m
Flow rate up to 1200 l/h
Model
Single-phase
GDWm 1A-2”
Three-phase
GDW1A-2”
Power
kW
0.75
Hp
1.0
Suction
Q.Max.
H.Max.
Size
M
L/h
M
Inch
15
1200
54
20
960
40
25
720
35
30
360
28
35
240
23
×1 ×1
1.25×1×1
1.25×1×1
1.25×1×1
1.25×1×1
Dimension
× ×H)mm
(L W
N/W
Kg
1.25
423
×288×245
19
GDWm “JET” self-priming
priming electropumps for 4” well
RANGEOFPERFORMANCE
Suction lift down to 45 m
Flow rate up to 3600 l/h
Model
Single-phase
GDWm 1A-4”
Three-phase
GDW1A-4”
Power
kW
0.75
Hp
1.0
Suction
Q.Max
Q.Max.
H.Max.
Size
M
L/h
M
Inch
15
1440
53
20
1200
46
30
480
32
35
240
25
×1 ×1
1.25×1×1
1.25×1×1
1.25×1×1
Dimension
× ×H)mm
(L W
N/W
Kg
1.25
423
×288×245
20
QDX SUBMERSIBLE DRAINAGE PUMPS (FOR CLEAN WATER)
RANGEOFPERFORMANCE
USES AND INSTALLATIONS
Flow rate up to 1000 l/min (60.5 m3/h)
Head up to 32.5 m
They are recommended for pumping clean water and
liquids that are chemically non aggressive for the
materials of which the pump is made. As portable
electric drainage and irrigation devices, QDX series
submersible pumps with lower water input are widely
suitable for water cluster boxes, farmland, industrial
and mining enterprises, construction sites, ship and
family, and characterized by less volume, light weight
and convenient operation etc. if the pump is fitted
with a floating switch, it is possible to achieve the
automatic control of start-stop action under no one’s
care. Single phase capacitor running asynchronous
or 3-phase asynchronous motor is equipped in this
pump and installed with a built-in thermal protector,
and can be automatically cut-off in the cases of
overheat or over current, thus assuring safe and
reliable running under worse circumstances.
LIMITS OF USE
Maximum submersible depth 3 m
Liquid temperature up to + 40°C
Environment temperature up to + 40°C
CONSTRUCTION CHARACTERISTICS
● PUMP BODY: aluminum and cast iron
● MOTOR BRACKET: aluminum
● IMPELLER: aluminum.or POM
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: ceramic – graphite, ceramic
– ceramic
● ELECTRIC MOTOR: QDX: single-phase 230 V50 Hz with condenser and thermal overload protector
built into the winding QX: three-phase 230/400 V - 50
Hz.
● INSULATION: class B.
● PROTECTION: IP X8.
GUARANTEE 1 YEAR
subject to our general terms of sale.
WORKING PRINCIPLE
They are recommended for pumping clean water and
liquids that are chemically non aggressive for the
materials of which the pump is made. As portable
electric drainage and irrigation devices, QDX series
submersible pumps with lower water input are widely
suitable for water cluster boxes, farmland, industrial
and mining enterprises, construction sites, ship and
QDX SUBMERSIBLE DRAINAGE PUMPS (FOR CLEAN WATER)
Single-phase
Model
Three-phase
Freq.
Hz
kW
Power
HP
Q.rat.
m3/h
H.rat.
m
Size
mm
QDX1.5-12-0.25
-
50
0.25
0.37
1.5
12
25
QDX1.5-17-0.37
-
50
0.37
0.5
1.5
17
25
QDX1.5-25-0.55
-
50
0.55
0.75
1.5
25
25
QDX3-18-0.55
-
50
0.55
0.75
3
18
32
QDX10-12-0.55
-
50
0.55
0.75
10
12
38
QDX15-7-0.55
-
50
0.55
0.75
15
7
51
QDX1.5-32-0.75
-
50
0.75
1
1.5
32
25
QDX3-24-0.75
-
50
0.75
1
3
24
32
QDX8-18-0.75
-
50
0.75
1
8
18
38
QDX10-16-0.75
-
50
0.75
1
10
16
51
QDX15-10-0.75
-
50
0.75
1
15
10
64
QDX25-6-0.75
-
50
0.75
1
25
6
76
QDX3-30-1.1
QX3-30-1.1
50
1.1
1.5
3
30
25
QDX15-14-1.1
QX15-14-1.1
50
1.1
1.5
15
14
64
QDX40-6-1.1
QX40-6-1.1
50
1.1
1.5
40
6
76
QDX6-25-1.1
QX6-25-1.1
50
1.1
1.5
6
25
51
-
QX40-9-1.5
50
1.5
2
40
9
64
-
QX25-12-1.5
50
1.5
2
25
12
76
Dimension
mm
×165×165
370×160×210
370×205×210
370×195×205
370×195×205
370×195×230
380×220×220
395×195×195
395×195×220
395×195×220
395×195×245
400×170×250
440×220×205
425×280×200
450×280×200
520×240×275
450×280×200
425×280×200
365
N/W
kg
G/W
kg
4.5
5
6.5
7
9.5
10
9.5
10
9.5
10
9.5
10
11.5
12
11.5
12
11
11.5
11.5
12
11.5
12
11.5
12
13
13.5
15.5
16
17.5
18
24
28
17.5
19
16.5
17
QDX-A SUBMERSIBLE DRAINAGE PUMPS
RANGEOFPERFORMANCE
USES AND INSTALLATIONS
Flow rate up to 250l/min (15 m3/h)
Head up to 18 m
Pumps are designed to lift dirty water which is not
chemically aggressive to the pump components. In
all cased where suspended solids up to 10mm have
to be deal with. Recommended applications therefore
include draining flooding in confined areas such as
basements and garages, and also pumping domestic
waste and the disposal of waste water, containing
fibrous matter and is also widely used in many
factories. These pumps are easy to install and
dependable when used automatically in fixed
installations. A purposely built pit with minimum
dimensions 450*450*450mm is recommended for
fixed installations, to provide total drainage and allow
correct operation of the float switch. This system
automatically starts the pump when the fluid reaches
a preset level, stopping it once the fluid has been
emptied. Installing a suitable not-return valve on the
delivery pipe prevents reverse flow when the pump
stops.
LIMITS OF USE
Maximum submersible depth 5 m
Liquid temperature up to + 40°C
Environment temperature up to + 40°C
CONSTRUCTION CHARACTERISTICS
● PUMP BODY: aluminum
● MOTOR BRACKET: aluminum
● IMPELLER: stainless steel with rubber covered
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: ceramic – graphite
● ELECTRIC MOTOR: single-phase 230 V- 50 Hz
with condenser and thermal overload protector built
into the winding
● INSULATION: class B.
● PROTECTION: IP X8.
WORKING PRINCIPLE
Pumps are submersible vortex, for dirty water,
designed mainly for domestic use and industrial use.
Their operating principle is that of a centrifugal pump
with a retracted vortex impeller. A
GUARANTEE 1 YEAR
subject to our general terms of sale.
Model
Single-phase
Power
kW
Voltage
V
Outlet
Mm
Q.Max. H.Max.
L/min
m
QDX500AF
0.50
220/50Hz
50
210
12
QDX750AF
0.75
220/50Hz
75
250
18
Dimension
mm
×225×415
325×225×435
250
G/W
kg
15
15
GS GARDEN SUBMERSIBLE PUMPS WITH DC POWER
RANGE OF PERFORMANCE
WORKING PRINCIPLE
Flow rate up to 80 l/min (4.8 m3/h)
Head up to 3.5 m
Small electrical irrigation and drainage equipments.
This pumps are particularly applied in urban well
water pumping, field irrigation and drainage, garden
irrigation and household water supply, as well as
drainage of industrial accumulated water, water
supply and drainage for construction livestock
breeding, etc.
LIMITS OF USE
Maximum operating depth 5m below water level
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
PH value in water: 6.5-8.0
GUARANTEE 1 YEAR
CONSTRUCTION CHARACTERISTICS
● PUMP BODY: plastic
● IMPELLER: reinforced nylon with fibre half open
● INSULATION: class F.
● PROTECTION: IP X8.
subject to our general terms of sale.
Model
Single-phase
Voltage
V
Outlet
Mm
Q.Max. H.Max.
L/min
m
GS50
12
20
12
0.85
GS80
12
40
80
3.5
Dimension
mm
×140×180
140×140×180
140
G/W
kg
1.0
1.0
GP GARDEN SUBMERSIBLE PUMPS
RANGE OF PERFORMANCE
WORKING PRINCIPLE
Flow rate up to 233 l/min (14 m3/h)
Head up to 9.0 m
They are recommended for pumping clean water and
liquids that are chemically non aggressive for the
materials of which the pump is made. As portable
electric drainage and irrigation devices, this series
submersible pumps with lower water input are widely
suitable for water cluster boxes, farmland, industrial
and mining enterprises, construction sites, ship and
emptying sump pits.
LIMITS OF USE
Maximum operating depth 5m below water level
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
CONSTRUCTION CHARACTERISTICS
● PUMP BODY: plastic
● IMPELLER: POM
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: ceramic – graphite, ceramic
– ceramic
● ELECTRIC MOTOR: single-phase 230 V- 50 Hz
with condenser and thermal overload protector built
into the winding.
● INSULATION: class B.
● PROTECTION: IP X8.
Model
GUARANTEE 1 YEAR
subject to our general terms of sale.
Single-phase
Three-phase
Freq.
Hz
Power
kW
Q.rat.
m3/h
H.rat.
m
GP400F
-
50
0.40
7.9
5.0
GP550F
-
50
0.55
10.0
6.5
GP750F
-
50
0.75
13.0
7.5
GP900F
-
50
0.90
14.0
8.5
Dimension
mm
×160×350
220×160×370
220×160×370
220×160×370
220
N/W
kg
G/W
kg
4.5
5
4.8
5.1
5.0
5.4
5.3
5.6
GSP GARDEN SUBMERSIBLE PUMPS
RANGE OF PERFORMANCE
WORKING PRINCIPLE
Flow rate up to 50 l/min (3.0 m3/h)
Head up to 6.0 m
They are recommended for pumping clean water and
liquids that are chemically non aggressive for the
materials of which the pump is made. As portable
electric drainage and irrigation devices, this series
submersible pumps with lower water input are widely
suitable for water cluster boxes, farmland, industrial
and mining enterprises, construction sites, ship and
emptying sump pits.
LIMITS OF USE
Maximum operating depth 5m below water level
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
Maximum passage for suspended solids ∮4mm
PH value in water: 6.5-8.0
GUARANTEE 1 YEAR
CONSTRUCTION CHARACTERISTICS
● PUMP BODY: plastic
● IMPELLER: reinforced nylon with fibre half open
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: stainless steel, ceramic –
graphite
● ELECTRIC MOTOR: single-phase 230 V- 50 Hz
with condenser and thermal overload protector built
into the winding.
● INSULATION: class F.
● PROTECTION: IP X8.
subject to our general terms of sale.
Model
Single-phase
Freq.
Hz
Power
kW
Outlet
Mm
Q.Max. H.Max.
Q.Max
L/min
m
GSP100F
220V/50Hz
0.10
25 20 15
50
6
GSP120F
220V/50Hz
0.12
25 20 15
50
6
Dimension
mm
×175×315
175×175×275
230
G/W
kg
4.3
4.3
GPOP SUBMERSIBLE DRAINAGE PUMPS
RANGE OF PERFORMANCE
WORKING PRINCIPLE
Flow rate up to 140 l/min (8.4 m3/h)
Head up to 9.0 m
They are recommended for pumping clean water and
liquids that are chemically non aggressive for the
materials of which the pump is made. As portable
electric drainage and irrigation devices, this series
submersible pumps with lower water input are widely
suitable for water cluster boxes, farmland, industrial
and mining enterprises, construction sites, ship and
emptying sump pits.
LIMITS OF USE
Maximum operating depth 3m below water level
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
Maximum passage for suspended solids ∮10mm
CONSTRUCTION CHARACTERISTICS
● PUMP BODY: fiberglass reinforced technopolymer
● IMPELLER: general electric Noryl gfn2v
technoplymer
● MOTOR SHAFT: 45# steel or stainless steel
● MECHANICAL SEAL: double type
● ELECTRIC MOTOR: sealed induction motor, built
in thermal overload protector.
● INSULATION: class F
● PROTECTION: IP 68.
GUARANTEE 1 YEAR
subject to our general terms of sale.
Single-phase
Three-phase
Hz
kW
Mm
L/min
H.rat
.
m
GPOP250F
-
50
0.25
25
65
6
GPOP370F
-
50
0.37
32
75
7
GPOP371F
-
50
0.37
32
150
8
Model
Freq.
Power
Outlet
Q.Max.
Dimension
G/W
mm
kg
×190×330
200×190×330
200×190×350
200
4.3
5.3
5.8
GV SUBMERSIBLE SEWAGE PUMPS
LIMITS OF USE
WORKING PRINCIPLE
Max. immersion depth: 5m
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
Liquid pH value: 4-10
Liquid kinematic viscosity: 7 ×10-7 ～23 ×10-6m2/s
Max. liquid density: 1.2 ×10-3kg/m3
They are recommended for pumping waste water
from factories, construction sites and commercial
facilities, drainage system in municipal sewage
treatment plants; drainage station in residential
quarters and municipal projects or methane pools
and field irrigation in country side
CONSTRUCTION CHARACTERISTICS
GUARANTEE 1 YEAR
● COPPER WINDING
● BUILT-IN THERMAL PROTECTOR
● MOTOR SHAFT: Stainless steel
● INSULATION: class F.
● PROTECTION: IP X8.
subject to our general terms of sale.
Single-phase
Three-phase
Hz
kW
Outlet
Size
Mm
GV180F
-
50
0.18
25 32 40
133
7.0
15
GV250F
-
50
0.25
25 32 40
150
7.5
15
GV450F
-
50
0.45
50
200
8.5
25
GV750F
-
50
0.75
50
300
10.5
25
Model
Freq. Power
Max.
Flow
L/min
Max.
Head
M
Max Diameter of
Particle
Mm
Dimension
G/W
mm
kg
×180×365
185×180×385
255×195×495
255×195×535
185
9.0
9.5
17.5
22
GV SUBMERSIBLE SEWAGE PUMPS
LIMITS OF USE
WORKING PRINCIPLE
Max. immersion depth: 5m
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
Liquid pH value: 4-10
Liquid kinematic viscosity: 7 ×10-7 ～23 ×10-6m2/s
Max. liquid density: 1.2 ×10-3kg/m3
They are recommended for pumping waste water
from factories, construction sites and commercial
facilities, drainage system in municipal sewage
treatment plants; drainage station in residential
quarters and municipal projects or methane pools
and field irrigation in country side
CONSTRUCTION CHARACTERISTICS
GUARANTEE 1 YEAR
● COPPER WINDING
● BUILT-IN THERMAL PROTECTOR
● MOTOR SHAFT: Stainless steel
● INSULATION: class F.
● PROTECTION: IP X8.
subject to our general terms of sale.
Single-phase
Three-phase
Hz
kW
Outlet
Size
Mm
GV1100F
-
50
1.1
50
333
9.0
35
GV1101F
-
50
1.1
50
416
15
25
GV1500F
-
50
1.5
40
300
22
10
Model
Freq. Power
Max.
Flow
L/min
Max.
Head
M
Max Diameter of
Particle
Mm
Dimension
G/W
mm
kg
×225×560
275×225×530
590×355×250
275
23.5
22
27
GVS SUBMERSIBLE SEWAGE PUMPS
LIMITS OF USE
WORKING PRINCIPLE
Max. immersion depth: 5m
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
Liquid pH value: 4-10
Liquid kinematic viscosity: 7 ×10-7 ～23 ×10-6m2/s
Max. liquid density: 1.2 ×10-3kg/m3
They are recommended for pumping waste water
from factories, construction sites and commercial
facilities, drainage system in municipal sewage
treatment plants; drainage station in residential
quarters and municipal projects or methane pools
and field irrigation in country side
CONSTRUCTION CHARACTERISTICS
GUARANTEE 1 YEAR
● COPPER WINDING
● BUILT-IN THERMAL PROTECTOR
● MOTOR SHAFT: Stainless steel
● INSULATION: class F.
● PROTECTION: IP X8.
subject to our general terms of sale.
Single-phase
Three-phase
Hz
kW
Outlet
Size
Mm
GVS1501F
-
50
1.5
50
450
18.5
20
GVS2201F
-
50
2.2
75
700
17
20
GVS2211F
-
50
2.2
100
990
18.5
20
Model
Freq. Power
Max.
Flow
L/min
Max.
Head
M
Max Diameter of
Particle
Mm
Dimension
G/W
mm
kg
×355×250
590×355×250
590×355×265
590
28
33
38
GVS SUBMERSIBLE SEWAGE PUMPS
LIMITS OF USE
WORKING PRINCIPLE
Max. immersion depth: 5m
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
Liquid pH value: 4-10
Liquid kinematic viscosity: 7 ×10-7 ～23 ×10-6m2/s
Max. liquid density: 1.2 ×10-3kg/m3
They are recommended for pumping waste water
from factories, construction sites and commercial
facilities, drainage system in municipal sewage
treatment plants; drainage station in residential
quarters and municipal projects or methane pools
and field irrigation in country side
CONSTRUCTION CHARACTERISTICS
GUARANTEE 1 YEAR
● COPPER WINDING
● BUILT-IN THERMAL PROTECTOR
● MOTOR SHAFT: Stainless steel
● INSULATION: class F.
● PROTECTION: IP X8.
subject to our general terms of sale.
Single-phase
Three-phase
Hz
kW
Outlet
Size
Mm
GVS750F
-
50
0.75
75
650
8
-
GVS1100F
-
50
1.1
40 32 25
250
20
-
GVS1500F
-
50
1.5
40 32 25
216
34
-
Model
Freq. Power
Max.
Flow
L/min
Max.
Head
M
Max Diameter of
Particle
Mm
Dimension
G/W
mm
kg
×355×250
270×220×500
270×220×550
590
24.5
21
25
4GVS MULTI STAGE SUBMERSIBLE SEWAGE PUMPS
LIMITS OF USE
WORKING PRINCIPLE
Max. immersion depth: 5m
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
Liquid pH value: 4-10
Liquid kinematic viscosity: 7 ×10-7 ～23 ×10-6m2/s
Max. liquid density: 1.2 ×10-3kg/m3
Pump consists centrifugal pumps, designed for
permanently or partially immersed operation to
produce higher head with multi stage impellers. The
impellers are installed on the same shaft and rotate
inside vane diffuser. They are recommended for
pumping waste water from factories, construction
sites and commercial facilities, drainage system in
municipal sewage treatment plants; drainage station
in residential quarters and municipal projects or
methane pools and field irrigation in country side
CONSTRUCTION CHARACTERISTICS
● COPPER WINDING
● BUILT-IN THERMAL PROTECTOR
● MOTOR SHAFT: Stainless steel
● INSULATION: class F.
● PROTECTION: IP X8.
GUARANTEE 1 YEAR
subject to our general terms of sale.
Single-phase
Three-phase
Hz
kW
Outlet
Size
Mm
2GVS750F
-
50
0.75
50
200
25
-
2GVS1100F
-
50
1.1
50
250
30
-
3GVS1500F
-
50
1.5
50
240
42
-
50
1.8
50
240
55
Model
4GVS1800F
Freq. Power
Max.
Flow
L/min
Max.
Head
M
Max Diameter of
Particle
Mm
Dimension
G/W
mm
kg
×285×205
625×285×205
625×285×205
660×285×205
550
20.0
20.5
27.5
31.5
7GV MULTI STAGE SUBMERSIBLE SEWAGE PUMPS
RANGE OF PERFORMANCE
WORKING PRINCIPLE AND USAGE
Flow rate up to 100 l/min (6.0 m3/h)
Head up to 77.0 m
Pump consists centrifugal pumps, designed for
permanently or partially immersed operation to
produce higher head with multi stage impellers. The
impellers are installed on the same shaft and rotate
inside vane diffuser. Channeling the fluid from each
impeller to the suction opening of the next. The fluid
passes through the impellers and leaves the pump
via the delivery opening machined in the pump body.
They are recommended for pumping fluids, used in
domestic, civil and industrial fields, for the automatic
distribution of water working in conjunction with surge
tanks, from emptying basins, tank, sump pits, for
washing and pressure boosting system, and for firefighting purposes, etc, where need higher head.
LIMITS OF USE
Max. immersion depth: 5m
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
Liquid pH value: 6.5-8.0
CONSTRUCTION CHARACTERISTICS
● PUMP BODY: stainless steel
● MOTOR BRACKET: aluminum
● MECHANICAL SEAL: ceramic to graphite
● IMPELLER: stainless steel with centrifugal radial
● MOTOR: built in thermal protector
● MOTOR SHAFT: Stainless steel or 45#
● INSULATION: class F.
● PROTECTION: IP X8.
Model
Freq.
Power
GUARANTEE 1 YEAR
subject to our general terms of sale.
Outlet Max.
Size Flow
Mm L/min
Max.
Head
M
Single-phase
Three-phase
Hz
kW
5GV900F
-
220V50Hz
0.9
25
110
53
6GV1100F
-
220V50Hz
1.1
25
100
65
7GV1300F
-
220V50Hz
1.3
25
100
77
Dimension
G/W
mm
kg
×250×200
550×250×200
575×250×200
525
14.5
16.0
17.5
GV-K SUBMERSIBLE SEWAGE PUMPS
LIMITS OF USE
WORKING PRINCIPLE
Max. immersion depth: 5m
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
Liquid pH value: 4-10
Liquid kinematic viscosity: 7 ×10-7 ～23 ×10-6m2/s
Max. liquid density: 1.2 ×10-3kg/m3
They are recommended for pumping waste water
from factories, construction sites and commercial
facilities, drainage system in municipal sewage
treatment plants; drainage station in residential
quarters and municipal projects or methane pools
and field irrigation in country side
CONSTRUCTION CHARACTERISTICS
GUARANTEE 1 YEAR
● COPPER WINDING
● BUILT-IN THERMAL PROTECTOR
● MOTOR SHAFT: Stainless steel
● INSULATION: class F.
● PROTECTION: IP X8.
subject to our general terms of sale.
Single-phase
Three-phase
Hz
kW
Outlet
Size
Mm
GV1100KF
-
50
1.1
50
233
7.0
-
GV1300KF
-
50
1.3
50
300
12
-
GV1800KF
-
50
1.8
75
400
10
-
Model
Freq. Power
Max.
Flow
L/min
Max.
Head
M
Max Diameter of
Particle
Mm
Dimension
G/W
mm
kg
×225×560
565×305×245
590×355×250
275
24
25.5
32.5
GV-K SUBMERSIBLE SEWAGE PUMPS
LIMITS OF USE
WORKING PRINCIPLE
Max. immersion depth: 5m
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
Liquid pH value: 4-10
Liquid kinematic viscosity: 7 ×10-7 ～23 ×10-6m2/s
Max. liquid density: 1.2 ×10-3kg/m3
They are recommended for pumping waste water
from factories, construction sites and commercial
facilities, drainage system in municipal sewage
treatment plants; drainage station in residential
quarters and municipal projects or methane pools
and field irrigation in country side
CONSTRUCTION CHARACTERISTICS
GUARANTEE 1 YEAR
● COPPER WINDING
● BUILT-IN THERMAL PROTECTOR
● MOTOR SHAFT: Stainless steel
● INSULATION: class F.
● PROTECTION: IP X8.
subject to our general terms of sale.
Single-phase
Three-phase
Hz
kW
Outlet
Size
Mm
GV1500KF
-
50
1.5
50
250
14.5
-
GV1801KF
-
50
1.8
50
350
25
-
GV2200KF
-
50
2.2
75
520
10
-
Model
Freq. Power
Max.
Flow
L/min
Max.
Head
M
Max Diameter of
Particle
Mm
Dimension
G/W
mm
kg
×355×250
590×355×250
590×355×250
590
31.5
38
31.5
GV-K SUBMERSIBLE SEWAGE PUMPS
LIMITS OF USE
WORKING PRINCIPLE
Max. immersion depth: 5m
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
Liquid pH value: 4-10
Liquid kinematic viscosity: 7 ×10-7 ～23 ×10-6m2/s
Max. liquid density: 1.2 ×10-3kg/m3
They are recommended for pumping waste water
from factories, construction sites and commercial
facilities, drainage system in municipal sewage
treatment plants; drainage station in residential
quarters and municipal projects or methane pools
and field irrigation in country side
CONSTRUCTION CHARACTERISTICS
GUARANTEE 1 YEAR
● COPPER WINDING
● BUILT-IN THERMAL PROTECTOR
● MOTOR SHAFT: Stainless steel
● INSULATION: class F.
● PROTECTION: IP X8.
subject to our general terms of sale.
Single-phase
Hz
kW
Outlet
Size
Mm
GV1502KF
50
1.5
50
180
18
-
GV1802KF
50
1.8
50
230
21
-
Model
Freq. Power
Max.
Flow
L/min
Max.
Head
M
Max Diameter of
Particle
Mm
Dimension
G/W
mm
kg
×355×250
590×355×250
590
31
34.5
QGD SUBMERSIBLE SCREW PUMPS
LIMITS OF USE
APPLICATION
Max. immersion depth: 15m
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
For pumping clean water with sand content less than
150g/m3.
For well pumping, river pumping, farm irrigation,
water supply, mining, drainage in breeding industry.
CONSTRUCTION CHARACTERISTICS
GUARANTEE 1 YEAR
● COPPER WINDING
● BUILT-IN THERMAL PROTECTOR
● MOTOR SHAFT: Stainless steel
● INSULATION: class B
● PROTECTION: IP X8.
subject to our general terms of sale.
kW
Outlet
Size
Inch
Rated.
Flow
M3/h
Rated.
Head
M
50
0.37
1”
1.2
50
QGD1.5-50-0.55
50
0.55
1”
1.2
50
QGD1.5-65-0.75
50
0.75
1”
1.5
65
QGD1.5-100-1.1
50
1.1
1”
1.5
100
Model
Freq.
Power
Single-phase
Hz
QGD1.2-50-0.37
Dimension
G/W
mm
kg
×115×195
575×115×195
615×150×190
690×150×190
545
14
15
23
25
QJD SUBMERSIBLE DRY DEEP WELL PUMPS
LIMITS OF USE
CONSTRUCTION CHARACTERISTICS
Max. immersion depth: 15m
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
Sand content less than 150g/m3.
Min. well diameter: 4”
● PUMP BODY: stainless steel
● MOTOR BRACKET: stainless steel
● IMPELLER: POM
● MOTOR: copper winding， dry type
● MOTOR AND PUMP SHAFT: Stainless steel
● INSULATION: class B
● PROTECTION: IP X8.
● OUTLET DIAMETER: 1”
APPLICATION
For pumping clean water with sand content less than
150g/m3.
For well pumping, river pumping, farm irrigation,
water supply, mining, drainage in breeding industry.
Model
Power
GUARANTEE 1 YEAR
subject to our general terms of sale.
DELIVERY
Weight
Single-Phase
KW
m3/h
0
1.2
2.4
3.6
4.8
6
L/min
0
20
40
60
80
100
DIM
HP
QJD2/7-0.5
0.5
0.7
45
43
40
33
17
_
QJD4/6-0.37
0.37
0.5
38
36
31
27
18
_
QJD4/8-0.55
0.55
1.75
52
48
44
37
22
_
63
59
55
45
20
_
H
（m)
QJD4/10-0.75
0.75
1
QJD4/14-1.1
1.1
1.5
90
87
80
65
34
6
QJD4/18-1.5
1.1
1.5
118
111
104
81
45
7.2
×110×185
700×110×185
785×110×185
875×110×185
1085×110×185
1350×110×185
745
G(s)
16
15
17
18
21
27
GDW SUBMERSIBLE DEEP WELL PUMPS
LIMITS OF USE
APPLICATION
Max. immersion depth: 48m
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
For pumping clean water with sand content less than
150g/m3.
For well pumping, river pumping, farm irrigation,
water supply, mining, drainage in breeding industry.
CONSTRUCTION CHARACTERISTICS
GUARANTEE 1 YEAR
● COPPER WINDING
● BUILT-IN THERMAL PROTECTOR
● MOTOR SHAFT: Stainless steel
● INSULATION: class B
● PROTECTION: IP X8.
subject to our general terms of sale.
Model
Freq.
Power
Outlet
Size
Max
Flow
Max.
Head
Dimension
G/W
Single-phase
Hz
kW
Inch
M3/h
M
mm
kg
50
0.37
1”
3.6
48
4GDW6/48
545
×115×195
14
75SDm SUBMERSIBLE DEEP WELL PUMPS
LIMITS OF USE
APPLICATION
Max. immersion depth: 70m
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
Sand content less than 150g/m3.
Min. well diameter: 3.0”
For pumping clean water with sand content less than
150g/m3.
For well pumping, river pumping, farm irrigation,
water supply, mining, drainage in breeding industry.
CONSTRUCTION CHARACTERISTICS
GUARANTEE 1 YEAR
● PUMP BODY: stainless steel
● MOTOR BRACKET: stainless steel
● IMPELLER: POM
● MOTOR: copper winding filled with oil.
● MOTOR AND PUMP SHAFT: Stainless steel
● INSULATION: class B
● PROTECTION: IP X8.
● OUTLET DIAMETER: 1”
subject to our general terms of sale.
～
Model
1
220V/240V
3SDm2/07
3SDm2/10
3SDm2/14
3SDm2/20
3SDm2/27
3SDm2/33
～
3
380V/415V
3SD2/07
3SD2/10
3SD2/14
3SD2/20
3SD2/27
3SD2/33
Power
Hp
0.25
0.33
0.5
0.75
1.0
1.5
m3/h
l/min
0
0
29
42
59
H (m)
84
113
139
Delivery
0.3
0.6
0.9
10
15
5
27
26
24
41
39
41
57
55
57
82
81
78
111 109 105
135 134 129
1.2
20
23
37
52
74
100
122
1.5
25
22
34
48
68
92
112
≈
n 2850 l/min
1.8
2.1
2.4
30
35
40
19
16
11
30
26
21
42
36
29
60
52
41
81
70
55
99
86
68
2.7
45
6
15
20
29
39
48
3
50
3
9
13
18
24
30
90SDm SUBMERSIBLE DEEP WELL PUMPS
LIMITS OF USE
CONSTRUCTION CHARACTERISTICS
Max. immersion depth: 70m
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
Sand content less than 150g/m3.
Min. well diameter: 3.5”
● PUMP BODY: stainless steel
● MOTOR BRACKET: stainless steel
● IMPELLER: POM
● MOTOR: copper winding filled with oil.
● MOTOR AND PUMP SHAFT: Stainless steel
● INSULATION: class B
● PROTECTION: IP X8.
● OUTLET DIAMETER: 1”
APPLICATION
For pumping clean water with sand content less than
150g/m3.
For well pumping, river pumping, farm irrigation,
water supply, mining, drainage in breeding industry.
Model
Single-Phase
220~230v/50Hz
3.5SDm1/9
3.5SDm1/12
3.5SDm1/18
3.5SDm1/22
3.5SDm1/26
Model
Power
KW
HP
0.37 0.5
0.55 1.75
0.75
1
1.1 1.5
1.5
2
GUARANTEE 1 YEAR
subject to our general terms of sale.
DELIVERY
m3/h
L/min
H
（m)
0
0
54
71
107
131
155
Power
0.6
10
40
60
85
106
136
1.2
20
30
40
52
71
86
1.8
30
10
15
18
34
37
Weight
(KG)
DIM mm
×
×
×
×
×
×
×
×
×
×
920 174 125
1040 174 125
1230 174 125
1400 174 125
1560 174 125
DELIVERY
Single-Phase
m3/h
0
KW HP
220~230v/50Hz
L/min
0
3.5SDm3/8
0.37 0.5
35
3.5SDm3/10
0.55 0.75
43
3.5SDm3/12
0.75 1
52
H m)
3.5SDm3/14
0.9 1.2
60
3.5SDm3/18
1.1 1.5
78
3.5SDm3/25
1.5
2
108
（
1.2
20
31
38
46
54
69
96
2.4
40
27
34
41
47
61
85
3.6
60
22
27
34
38
49
68
4.8
80
15
19
23
27
34
48
6
100
7
8
10
12
16
22
DIM mm
×
×
×
×
×
×
×
×
×
×
×
×
810 105 165
900 105 165
1000 105 165
1080 105 165
1230 105 165
1550 105 165
G(s)
14.5
16.5
19
20.5
24.5
Weight
(KG)
G(s)
12
13
15
16.5
18
23.5
4SDm2 3 SUBMERSIBLE DEEP WELL PUMPS
LIMITS OF USE
CONSTRUCTION CHARACTERISTICS
Max. immersion depth: 70m
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
Sand content less than 150g/m3.
Min. well diameter: 4”
● PUMP BODY: stainless steel
● MOTOR BRACKET: stainless steel
● IMPELLER: POM
● MOTOR: copper winding filled with oil.
● MOTOR AND PUMP SHAFT: Stainless steel
● INSULATION: class B
● PROTECTION: IP X8.
● OUTLET DIAMETER: 1”
APPLICATION
For pumping clean water with sand content less than
150g/m3.
For well pumping, river pumping, farm irrigation,
water supply, mining, drainage in breeding industry.
Model
Single-Phase
4SDm2/8
4SDm2/11
4SDm2/14
4SDm2/20
4SDm2/25
4SDm2/36
4SDm3/7
4SDm3/10
4SDm3/13
4SDm3/18
4SDm3/24
4SDm3/32
Power
ThreePhase
～
～
4SD2/14
4SD2/20
4SD2/25
4SD2/36
～
～
4SD3/13
4SD3/18
4SD3/24
4SD3/32
KW
HP
（
）
Q
m3/h
L/min
0.37 0.5
0.55 0.75
0.75
1
1.1 1.5
1.5
2
2.2
3
H m)
0.37 0.5
0.55 0.75
0.75
1
1.1 1.5
1.5
2
2.2
3
（
GUARANTEE 1 YEAR
subject to our general terms of sale.
DELIVERY
0
0
51
70
90
128
160
230
47
68
88
122
162
216
DIM
0.6 1.2
1.8
2.4
10
47
65
83
119
149
214
43
62
80
110
149
198
30
42
57
72
103
129
185
38
54
70
97
129
172
40 50
36 26
49 36
62 45
89 64
111 80
159 115
33 26
47 38
61 49
85 68
113 90
150 120
20
45
62
79
113
141
203
41
59
76
105
140
187
3
3.6
4.2
60
15
20
26
37
46
66
18
25
33
46
61
81
70
－
－
－
－
－
－
－
12
15
21
28
37
Weight
Single-Phase
Three-Phase
×174×125
1020×174×125
1130×174×125
1310×174×125
1500×174×125
1910×174×125
890×174×125
980×174×125
1075×174×125
1310×174×125
1500×174×125
1800×174×125
～
～
890
×174×125
1130×174×125
1255×174×125
1615×174×125
～
～
890×174×125
1075×174×125
1255×174×125
1550×174×125
890
G(s) G(t)
15
17
19
23
30
37
15
16
19
22
27
34
～
～
19
23
28
35
～
～
19
22
25
32
4SDm4 6 SUBMERSIBLE DEEP WELL PUMPS
LIMITS OF USE
CONSTRUCTION CHARACTERISTICS
Max. immersion depth: 70m
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
Sand content less than 150g/m3.
Min. well diameter: 4”
● PUMP BODY: stainless steel
● MOTOR BRACKET: stainless steel
● IMPELLER: POM
● MOTOR: copper winding filled with oil.
● MOTOR AND PUMP SHAFT: Stainless steel
● INSULATION: class B
● PROTECTION: IP X8.
● OUTLET DIAMETER: 1”
APPLICATION
For pumping clean water with sand content less than
150g/m3.
For well pumping, river pumping, farm irrigation,
water supply, mining, drainage in breeding industry.
Model
Power
GUARANTEE 1 YEAR
subject to our general terms of sale.
DELIVERY
Weight
(kg)
DIM
SinglePhase
4SDm4/6
4SDm4/8
4SDm4/10
4SDm4/14
4SDm4/18
4SDm4/25
ThreePhase
～
～
～
～
～
4SD4/10
4SD4/14
4SD4/18
4SD4/25
4SD4/32
4SD4/38
4SD4/42
～
～
～
4SD6/9
4SD6/12
4SD6/16
4SD6/21
4SD6/27
4SD6/33
4SD6/36
4SDm6/7
4SDm6/9
4SDm6/12
4SDm6/16
4SDm6/21
～
KW
0.37
0.55
0.75
1.1
1.5
2.2
3
3.7
4
0.55
0.75
1.1
1.5
2.2
3
3.7
4
m3/h
0
1.2
2.4
3.6
4.8
6
L/min
0
20
40
60
80
38
51
64
90
115
160
205
243
269
43
55
74
98
129
165
202
220
35
46
58
81
104
144
185
219
242
39
51
68
90
118
152
186
203
27
36
45
63
81
113
145
172
190
35
45
60
80
105
135
165
180
15
20
25
35
45
62
80
94
104
29 22
38 28
50 37
67 50
88 65
113 84
138 103
150 112
7.2
HP
0.5
0.75
1
1.5
2
3
4
5
5.5 H
0.75
1
1.5
2
3
4
5
5.5
（
43
57
71
100
129
179
229
271
m) 300
45
57
77
102
134
172
210
229
100 120
Single-Phase
Three-Phase
×174×125
×174×125
1075×174×125
1310×174×125
1500×174×125
1800×174×125
M:565×125×125
M:600×125×125
M:600×125×125
980×174×125
1130×174×125
1310×174×125
1500×174×125
1800×174×125
M:565×125×125
M:600×125×125
M:600×125×125
～
～
890
980
11
14
19
25
33
42
51
56
×174×125
×174×125
1255×174×125
1550×174×125
P:1360×125×125
P:1615×125×125
P:1680×125×125
～
890×174×125
1075×174×125
1255×174×125
1550×174×125
P: 1360×125×125
P: 1615×125×125
P: 1800×125×125
890
1075
G(s)
G(t)
14
16
16
17
17
20
20
25
25
31
28
M:16 P:17.5
M:18
P:19
M:18.5 P:20.5
16
15
18
17
21
20
24
22
27
25
M: 16
P:9
M:18
P:13
M: 18.5 P:13.5
4SDm8 SUBMERSIBLE DEEP WELL PUMPS
LIMITS OF USE
CONSTRUCTION CHARACTERISTICS
Max. immersion depth: 70m
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
Sand content less than 150g/m3.
Min. well diameter: 4”
● PUMP BODY: stainless steel
● MOTOR BRACKET: stainless steel
● IMPELLER: POM
● MOTOR: copper winding filled with oil.
● MOTOR AND PUMP SHAFT: Stainless steel
● INSULATION: class B
● PROTECTION: IP X8.
● OUTLET DIAMETER: 1”
APPLICATION
For pumping clean water with sand content less than
150g/m3.
For well pumping, river pumping, farm irrigation,
water supply, mining, drainage in breeding industry.
Model
Power
GUARANTEE 1 YEAR
subject to our general terms of sale.
DELIVERY
Weight
(kg)
DIM
SinglePhase
ThreeKW HP
Phase
m3/h
0 1.2 2.4 3.6 4.8 6 7.2 8.4
L/min 0
0.7
1
5
4SDm8/9 4SD8/9 1.1 1.5
4SDm8/12 4SD8/12 1.5 2
4SDm8/17 4SD8/17 2.2 3
4SDm8/7 4SD8/7
20 40 60 80 100 120 140
9.6
160
43 41 39 37 34 30 25
19
12
55 53 50 47 43 38 32
74 71 67 63 58 51 43
104 100 95 89 82 73 61
24
33
46
15
20
28
79
60
36
160 153 144 136 125 111 93
71
43
（m) 135 129 122 115 105 94
4SD8/22 3
4
4SD8/26 3.7
5
4SD8/29 4
5.5
178 170 161 151 139 124 104 79
47
4SD8/35 5.5 7.5
215 205 194 182 168 149 125 95
57
4SD8/38 5.5 7.5
234 223 211 198 182 162 136 103
62
H
Single-Phase
×174×125
1130×174×125
1360×174×125
1615×174×125
M:565×125×125
M:600×125×125
M:600×125×125
M:670×125×125
M:670×125×125
1020
Three-Phase
×174×125
935×174×125
1130×174×125
1360×174×125
P:1180×125×125
P:1360×125×125
P:1500×125×125
P:1800×125×125
P:1855×125×125
810
G(s)
G(t)
18
17
20
23
27
19
21
25
M:16
P:11
M:18
P:12
M:18.5 P:12.5
M:21
P:13
M:21
P;13.5
4SDm10 SUBMERSIBLE DEEP WELL PUMPS
LIMITS OF USE
CONSTRUCTION CHARACTERISTICS
Max. immersion depth: 70m
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
Sand content less than 150g/m3.
Min. well diameter: 4”
● PUMP BODY: stainless steel
● MOTOR BRACKET: stainless steel
● IMPELLER: POM
● MOTOR: copper winding filled with oil.
● MOTOR AND PUMP SHAFT: Stainless steel
● INSULATION: class B
● PROTECTION: IP X8.
● OUTLET DIAMETER: 1”
APPLICATION
For pumping clean water with sand content less than
150g/m3.
For well pumping, river pumping, farm irrigation,
water supply, mining, drainage in breeding industry.
Model
Power
GUARANTEE 1 YEAR
subject to our general terms of sale.
DELIVERY
DIM
Single-Phase
4SDm10/6
4SDm10/8
4SDm10/10
4SDm10/14
ThreePhase
KW HP
4SD10/6
4SD10/8
4SD10/10
4SD10/14
0.75 1
1.1 1.5
1.5
2
2.2
3
4SD10/18
3
4
4SD10/23
4
5.5
m3/h
0
3.6
4.8
L/min
0
60
37
49
62
86
（
6
7.2
8.4
9.6 10.8
12
80
100 120 140 160 180
200
34
45
57
79
33
43
54
76
31
41
51
72
29
38
48
67
26
34
43
60
22
30
37
52
18
24
30
42
13
17
21
30
111 102
97
92
86
77
67
54
38
142 130 124 118 109
99
85
69
49
H m)
4SD10/28 5.5
7.5
172 158 151 144 133 120 104
84
59
4SD10/31 5.5
7.5
191 175 168 159 147 133 115
93
66
4SD10/37 7.5
10
228 209 200 190 176 159 137 111
79
4SD10/40 7.5
10
247 226 216 205 190 172 148 120
85
Single-Phase
Three-Phase
Weight
(kg)
G(s)
G(t)
×174×125 810×174×125 18 17
×174×125 935×174×125 20 19
1310×174×125 1075×174×125 23
21
1550×174×125 1310×174×125 27
25
M:565×125×125 P:1130×125×125 M:16 P:9
M:600×125×125 P:1360×125×125 M:18.5P:13
M:670×125×125 P;1615×125×125 M:21 P:14
M:670×125×125 P;1800×125×125 M:21 P:16
M:770×125×125 P;2015×125×125 M:25.5P:17.5
M:770×125×125 P;2150×125×125 M:25.5P:18.5
1020
1130
4SRm2 4 SUBMERSIBLE DEEP WELL PUMPS
LIMITS OF USE
CONSTRUCTION CHARACTERISTICS
Max. immersion depth: 70m
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
Sand content less than 150g/m3.
Min. well diameter: 4”
● PUMP BODY: stainless steel
● MOTOR BRACKET: stainless steel
● IMPELLER: POM
● MOTOR: copper winding filled with oil.
● MOTOR AND PUMP SHAFT: Stainless steel
● INSULATION: class B
● PROTECTION: IP X8.
● OUTLET DIAMETER: 1”
APPLICATION
For pumping clean water with sand content less than
150g/m3.
For well pumping, river pumping, farm irrigation,
water supply, mining, drainage in breeding industry.
GUARANTEE 1 YEAR
subject to our general terms of sale.
4SRm6 8 SUBMERSIBLE DEEP WELL PUMPS
LIMITS OF USE
CONSTRUCTION CHARACTERISTICS
Max. immersion depth: 70m
Liquid temperature up to + 35°C
Environment temperature up to + 40°C
Sand content less than 150g/m3.
Min. well diameter: 4”
● PUMP BODY: stainless steel
● MOTOR BRACKET: stainless steel
● IMPELLER: POM
● MOTOR: copper winding filled with oil.
● MOTOR AND PUMP SHAFT: Stainless steel
● INSULATION: class B
● PROTECTION: IP X8.
● OUTLET DIAMETER: 1”
APPLICATION
For pumping clean water with sand content less than
150g/m3.
For well pumping, river pumping, farm irrigation,
water supply, mining, drainage in breeding industry.
GUARANTEE 1 YEAR
subject to our general terms of sale.