Download Report

Addressable Input/Output
I-9301 / I-9303
Module
I-9301 Single I/O
I-9303 Double I/O
Features and Benefits
1.
Addressable
I/O
with
24Vdc/5A,
110Vac/3A relay output contacts
2. Input can be configured as NO/NC or
self confirmation output
3. LED status indicator
4. Electronically addressable
5. Characteristics one input or output
6. First fix base for easy and safe
installation.
Description
Intelligent addressable input/output module. A
single/double volt free relay with N/O and N/C
change over contacts that can be driven via
the fire alarm loop. Commonly used for
overriding equipment such as AHU’s, Smoke
extracts, Lift returns, auto dialer, BMS, etc.
The input can be linked through a volt free
contact
switch
output
of
ancillary
equipment reporting to the fire alarm
controller. According to the pre-inputted
cause and effects interface programming,
the alarm controller sends out a start
command to the equipment required to
start. After receiving the command, the
module activates its relay to change state.
Once the equipment under control has
operated a confirmation signal can be sent
back to the fire alarm controller. The I9303 has two addresses, which can receive
the two different action orders from the
controller and has two different control
outputs and can affirm two different input
answering signals. Electronic addressing
can
be
done
through
Handheld
Programming tool (P-9910), purchased
separately.
Specification
Part Number
Protection rating
Approval
Output control mode
Output capacity
Relay contact
Operating voltage
Operating current loop
Operating Temperature
Addressing Mode
Application
Materials and colour
Dimension
Wiring
I-9301
I-9303
IP 30
LPCB
Relay NO/NC passive contacts
Passive:5A/24Vdc(3A/110Vac) ; Active: 24Vdc/ 1A
One
Two
Loop 24Vdc (16~28Vdc); Supply voltage 24Vdc(16~28Vdc)
Standby: 1mA ; Action: 5mA
-10°C to 50°C @ 90% relative humidity
Electronic programming with 1~242, Electronic programming with 1~242,
occupying 1 address
occupying 2 addresses
Indoor use
ABS / Ivory white
120mm x 80mm x 39mm
8 wires: 2 wire for loop ( non6 wires: 2 wire for loop ( nonpolarized) ; 2 wire for power cable( nonpolarized) ; 2 wire for power cable( nonpolarized) ; 4 wire for contact
polarized) ; 2 wire for contact
Addressable Input/Output
Module I-9301 / I-9303
Module Installation
The module should be installed in compliance
with all local codes and/or NFPA 72 National
Fire Alarm Code, NFPA 70 National Electrical
Code, BS5389, and EN45. It is installed onto a
standard one gang electrical box with a
mounting hole that have 6.5cm spacing.
I−930X
Programming
The address and device type of the module
can be programmed using GST handheld
programmer
(P-9910),
purchased
separately. Connect the two wires of the
handheld programmer to Z1 (14) , Z2 (15)
terminals of the sounder. For programming
I-9303, the first address it will take the
next address also.
WALL
Action
Intelligent I/O Monitor Unit
ELECTRICAL
BACK BOX
MOUNTING
BASE
1 2
3
4
5
6
7
8
16 15 14 13 12 11 10 9
Wiring and Connection
Z1 (14) AND Z2 (15) TERMINAL
Connect the wires to the required terminal
according to the wiring diagram. The Z1, Z2
connect to addressable fire detection loop,
non-polarized, the D1, D2 is for 24VDC power
supply, non-polarized, the I1 and G connect
with passive NO contact of the control device,
NC1, COM1, NO1 is for first Output Circuit. The
NC2, COM2, NO2 is for the second output
terminals+ and G is continual 24Vdc output for
D1, D2 for active control rated at 1A The cable
must be fire rated type and the size depends
on the distance and application. Minimum size
gauge 1.0mm²(18 AWG)
V+
G
COM1
NO1
NC1
COM2
NO2
NC2
FIELD DEVICE
PROGRAMMER
Selection of compatible Control Panels
Compatible with all GST Intelligent Fire
Alarm Panels GST 200, GST 5000, GST
9000.
Ordering Information:
Part No
I-9303
D1
D2
G
I1
I2
Z1
Z2
I-9301
I-9303
V+
G
COM1
NO1
NC1
Description
Intelligent
Single
Input/Output
Module
Intelligent
Double
Input/Output
Module
Weight
/Kg
Pack
Qty
per
Box
.198
120
.210
120
MANUFACTURED IN ACCORDANCE WITH
I-9301
D1
D2
G
I1
Z1
Z2
Note: Specifications are subject to change without notice.
+24v - ~---,----- ---
GND
~;
--+----------- -·
,
I
:-ttti=:
Dl
zf -1
Zl
D2
1-9301
V+ G
I . I
COM!
N
j
I
L
..
L__
Specification
Operating Voltage
Standby Current
Action Current
Output Capacity
Output Control Type
Programming
Method ·
One address within 1~ 242 .
polling,
Red,
flashes
when
illuminates in action.
Protectior IP30
Code Range
Indicator
Electrical Tripping Device
Fig. 4
System connection for volt-free output contact
controlling field device is shown in Fig. 5.
~
+24V
GND
Zl
Z2
I
Dl
02
Zl
Z2
1-9301
V+ G COMI NOI
'5
a.
.=
Ingress
Rating
Operating
Temperature
Relative Humidity
of
Material
Enclosure
Dimension
(L X W X H)
Weight
o·c ~ +49'C
::::::93%, non condensing
ABS
120mm x 80mm x 39mm
(with base)
About 194g (with base)
Accessories and Tools
Remark
Name
Model
P-9910B
Held
Hand
Programmer
Order separately
B-9310
Back Box
Order separately
~
0
()
Loop: 24V (16V-28V)
Power: 24VDC (20VDC-28VDC)
Loop :::::: 1mA Power:::::: 2mA
Loop :::::: 3mA Power:::::: 15mA
capacity
Output
contact
is
24VDC/5A
is
Voltage
capacity
output
24VDC/1A
Dry contact output
Electronically addressed
-
Limited Warranty
Controlled Device
Fig.5
Note:
Don't connect the module's contact to the AC
control loop directly, preventing the strong AC
interference signal from damaging the module or
controlled device.
The module is not used for gas extinguishing
equipment
GST warrants that the product will be free of charge
for repairing or replacing from defects in design,
materials and workmanship during the warranty period.
This warranty shall not apply to any product that is
found to have been improperly installed or used in any
way not in accordance with the instructions supplied
with the product. Anybody, including the agents,
distributors or employees, is not in the position to
amend the contents of this warranty. Please contact
your local distributor for products not covered by this
warranty.
This Data Sheet is subject to change without notice. Please contact GST for more information or questions.
Gulf Security Technology Co., Ltd.
No. 80, Changjiang East Road, QETDZ, Qinhuangdao, Hebei, P.R. China 066004
Tel: +86 (0) 335 8502434 Fax: +86 (0) 335 8502532
[email protected] www.gst.com.cn
30303029
Issue 4.09