Technical Databook Agricultural Tyres 2014/ 2015 agricultural tyres Contents Continental, trademark licensed by Continental AG. general The content of this publication is provided for information only and without responsibility. MITAS a.s. makes no representations about the accuracy, reliability, completeness or timeliness of the information in this publication. MITAS a.s. may, in its sole discretion, revise the information contained herein at any time without notice. The obligations and responsibilities of MITAS a.s. regarding its products are governed solely by the a greements under which they are sold. Unless otherwise agreed in writing, the information contained h erein does not become part of these agreements. This publication does not contain any guarantee or agreed quality of MITAS a.s. products or any warranty of merchantability, fitness for a particular purpose and non-infringement. MITAS a.s. may make changes in the products or services described at any time without notice. This publication is provided on an “as is” basis. To the extent permitted by law, MITAS a.s. makes no warranty, express or implied, and assumes no liability in connection with the use of the information contained in this publication. General information Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tyre designation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 5–7 8–9 Tyre typology and main applications of radial tyres . . . . . . . . . Overview by dimension and profile . . . . . . . . . . . . . . . . . . . . . . . 10 – 19 Radial tyres tractor Silent Speed Tyre SilentSpeedTyre (SST) . . . . . . . . . . . . Super Volume Tyre SuperVolumeTyre (SVT) . . . . . . . . . . . 65 Series wide tyre AC 65 . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Series wide tyre HC 70 . . . . . . . . . . . . . . . . . . . . . . . . . 70 Series wide tyre AC 70 G . . . . . . . . . . . . . . . . . . . . . . . . 85 Series standard tyre AC 85 . . . . . . . . . . . . . . . . . . . . . . . . . . harvester Drive wheel SVT CHO NEW ! . . . . . . . . . . . . . . . . SVT and AC 70 H/G/N . . . . . . . . . . . . . Drive wheel Steer wheel SVT, AC 70 G, AC 65 . . . . . . . . . . . . . . IMP Implement radial tyres All-Ground, Multi-Service . . . . . . . . . . . Multipurpose radial tyres AC70G, Agro-Trailer . . . . . . . . . . . . . . . MPT 20 – 23 24 – 29 30 –35 36 – 41 42 – 47 48 – 55 56 – 59 60 – 65 66 – 69 70 – 71 72 –77 Cross-ply tyres tractor Cross-ply tyres AS-Farmer . . . . . . . . . . . . . . . . . . . . . Steering tyre T 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . IMP Implement cross-ply tyres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MPT Multipurpose cross-ply tyres . . . . . . . . . . . . . . . . . . . . . . . . . . . . Garden tractor tyres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Handcart tyres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 – 83 84 – 85 86 – 91 92– 93 94 – 95 96 – 97 operating instructions Operating instructions tractor tyres . . . . . . . . . . . . . . . . . . . . . . 98 – 99 Operating instructions IMP / MPT tyres . . . . . . . . . . . . . . . . . . . 100 – 101 rims Rims and accessories, valves . . . . . . . . . . . . . . . . . . . . . . . . . 102 –112 service marks and logos displayed in this publication are the property of MITAS a.s. and/or its associates. Nothing in technology Application technology this publication should be construed as granting any license or right to the Trademarks. Without the express written Maintenance and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Filling the tyre with water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 – 115 Conversion table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 –119 MITAS a.s. is not liable for any direct, indirect, incidental, consequential or punitive damages arising out of the use of this publication. Information contained herein is not intended to announce product availability anywhere in the world. The Continental Trademark and logo displayed in this publication is licensed by Continental AG. All other trademarks, consent of MITAS a.s. the use of the Trademarks is prohibited. All text, images, graphics and other materials in this publication are subject to the copyright and other intellectual property rights of MITAS a.s.. MITAS a.s. owns the copyrights in the selection, coordination and arrangement of the materials in this publication. These materials may not be modified or copied for commercial use or distribution. addresses general Contents Sales organisations worldwide . . . . . . . . . . . . . . . . . . . . . . . . 122 – 123 Copyright © 2013 MITAS a.s.. All rights reserved. 2 agricultural tyres 3 General information The extensive technical data and other information relating to tyres and accessories on the following pages have been compiled to reflect as accurately and completely as possible the current state of development. Tyre designation Because of changes in our product range the tyre sizes given in this guide are not always identical to our available range. For marking the tyre load-capacity a nume- Uncoded maximum load capacity and tyre ric code, the load index (LI), is used. pressure data in lbs (1 lb = 0.454 kg) and PSI In addition to the Load Index, a Speed (1 PSI = 0.069 bar) is also given on multi-pur- Symbol (SS) is used to designate the speed pose tyres. These specifications form part category of the tyres, see tables below. of the designation according to US Safety general Introduction Regulation FMVSS 119**. For special information please contact us: MPT tyres also comply with current require- tyres will be given in ECE-Regulation ments on Tyre noise EC Directive (2001/43/EC) MITAS a.s. Svehlova 1900/3 106 00 Praha 10, Czech Republic No. 106*. For the addresses of our sales organisations see page 122/123. Load Index (LI) Warning 4 An equivalent designation for agricultural The following instructions must be observed if vehicle safety is to be guaran teed. This applies above all to instructions re- that may lead to tyre failure under certain circumstances. garding tyre pressure. Failure to comply with these instructions could result in tyre damage Blow-outs can cause traffic accidents involving damage to property and/or personal injury. agricultural tyres LI kg 61 257 62 265 63 272 64 280 65 290 66 300 67 307 68 315 69 325 70 335 71 345 72 355 73 365 74 375 75 387 76 400 77 412 78 425 79 437 80 450 81 462 82 475 83 487 84 500 85 515 86 530 87 545 88 560 89 580 90 600 91 615 92 630 93 650 94 670 95 690 * ECE = Economic commission for Europe, Genf **FMVSS = Federal Motor Vehicle Safety Standards LIkg 96 710 97 730 98 750 99 775 100 800 101 825 102 850 103 875 104 900 105 925 106 950 107 975 108 1000 109 1030 110 1060 111 1090 112 1120 113 1150 114 1180 115 1215 116 1250 117 1285 118 1320 119 1360 120 1400 121 1450 122 1500 123 1550 124 1600 125 1650 126 1700 127 1750 128 1800 129 1850 130 1900 LIkg 131 1950 132 2000 133 2060 134 2120 135 2180 136 2240 137 2300 138 2360 139 2430 140 2500 141 2575 142 2650 143 2725 144 2800 145 2900 146 3000 147 3075 148 3150 149 3250 150 3350 151 3450 152 3550 153 3650 154 3750 155 3875 156 4000 157 4125 158 4250 159 4375 160 4500 161 4625 162 4750 163 4875 164 5000 165 5150 LIkg 166 5300 167 5450 168 5600 169 5800 170 6000 171 6150 172 6300 173 6500 174 6700 175 6900 176 7100 177 7300 178 7500 179 7750 180 8000 181 8250 182 8500 183 8750 184 9000 185 9250 186 9500 187 9750 18810000 18910300 19010600 19110900 19211200 19311500 19411800 19512150 19612500 19712850 19813200 19913600 20014000 Speed Symbol (SS) SSSpeed in km/h A 1 5 A 2 10 A 3 15 A 4 20 A 5 25 A 6 30 A 7 35 A 8 40 B 50 C 60 D 65 E 70 F 80 G 90 J 100 K 110 L 120 M 130 N 140 5 Tyre designation general Tyre designation (please see also ETRTO - European Tyre and Rim Technical Organisation) Tyre D Outer diameter: the diameter of an inflated tyre at the outermost surface of the tread. W H W G D Ø Section width: the linear distance between the outsides of the sidewalls of an inflated tyre excluding elevations due to labelling (mar- kings), decorations or protective bands or ribs. Layout of tyre designation tractor radial tyre 380/85 R 28 (14.9 R 28) 133 A8 AC 85 H Section height: half the difference between the overall diameter and the nominal rim diameter. R Static loaded radius: distance between rim centre and paved surface. F R Rim F Rim width: the linear distance between the flanges of the rim. G Rim flange height Ø Nominal rim diameter Layout of tyre designation IMP tyre 15.5/80 - 24, 145 A6 • , 157 A6 , 12 PR AS-Farmer Explanation of tyre designations Tyre Tyre nominal H:W Tyre Rim dia. Tyre group TL2)PR3)LI4)SS5) outer dia. width ratio design1) (application) in inch mm or inch % in inch 380 /85 R 28 AS TL 133 A8 650 /65 R 38 AS TL 154 D 12.4 R 24 AS 119 A8 12.4 – 38 AS 12 PR 7.50 – 18 AS Front 8 PR 15.5 / 80 – 24 Implement 12 PR 18 x 7.00 – 8 Garden Tractor 4 PR 445 /65 R 22.5 MPT TL 160 G = radial R – = cross-ply 2) TL = tubeless TT = tube type see also table on page 5 1) 6 3) 4) 5) PR = Ply Rating (indicates load capacity for code designated tyres) LI = Load Index SS = Speed Symbol Layout of tyre designation MPT tyre 445/65 R 22.5 MPT agricultural tyres 160 G AC 70 + 7 Tyre typology The development of the SilentSpeedTyre SST, connects the outstanding field characteristics of a 65 series wide tyre with high comfort. Because with the SST the noise level in the operator‘s cab is reduced to a minimum. The SuperVolumeTyre SVT was developed primarily for powerful machines with over 180 hp. The extremely large volume of air ensures gentle ground handling when working with heavy loads. For tractors with up to 200 hp, the Continental range of premium radial tyres offers a choice of three all-rounders. The new harvester tyre SVT CHO has been designed as an extremely powerful tyre for big combine harvesters. SVT CHO is capable of higher maximum loads; at the same time the tyre permits gentler ground handling in the field and more comfort on the road. The 85 Series standard radial AC 85 is ideally suited for wide-ranging applications in the field and on the road. The HC 70 the new 70 Series wide tyre, has higher load capacities than normally available in the 70 Series segment; it therefore offers gentler ground handling and can carry very heavy loads. The AC 65 is a wide tyre with a 65% aspect ratio and is the ideal choice in this tractor segment, where it‘s about gentle ground handling and the ability to transport heavy loads, as well as traction and grassland suitability. The AC 70 G is the acknowledged grassland tyre in the Continental portfolio. general Main applications – radial tyres Main applications agricultural SilentSpeedTyre SST tyres SuperVolumeTyre SuperVolumeTyre SVT SVT CHO NEW ! Product description on page Type of tyre hp Driving speed 202430 SilentSpeedSuperVolume Harvester < 200 > 180 – 70 km/h* 70 km/h* 50 km/h Road performance, Transports Field work +++++ +++++ +++ AC 65 HC 70 AC 70 G AC 85 AC 70 H/G/N 34 40465264 Harvester – 50 km/h +++ Wide tyre < 200 70 km/h* Wide tyre < 180 50 km/h Wide tyre < 180 50 km/h Standard < 180 50 km/h ++++ +++ +++ +++ ++++ +++++ ++++ +++ +++ +++ › Cultivating, ploughing (high torque) ++++ +++++ ++++ ++++ +++ +++ › Seedbed preparation (high load) ++++ +++++ ++++ +++ ++ +++ Grassland application Cultivation of crop rows +++++++++++++ Wine cultivation and fruit growing * see page 98 +++++ = exellent ++++ = very good ++++ ++++ ++++ +++ +++ + Harvest application +++++ +++++ 8 SuperVolumeTyre +++ = good ++ ++ ++++ +++++ + ++ = suitable + ++ +++ +++ +++ + = suitable to limited extent 9 Overview by dimension and profile 265/70 R 16 MPT 114 G 285/80 R 16 MPT 126 G T C T SS SV T 65 SV AC AC 70 70 46 44 540/65 R 24 140 D (143 A8) 32 32 540/65 R 24 146 D (149 A8) 32 425/55 R 17 MPT 134 G 44 280/85 R 28 118 A8 (115 B) 50 325/70 R 18 MPT 125 G 44 320/85 R 28 124 A8 (121 B) 50 365/70 R 18 MPT 132 G 44 340/85 R 28 127 A8 (124 B) 50 275/80 R 20 MPT 131 G 44 380/70 R 28 127 D (130 A8) 38 280/85 R 20 117 D (120 A8) 50 380/85 R 28 133 A8 (130 B) 335/80 R 20 MPT 134 G 44 420/70 R 28 133 A8 (130 B) 375/70 R 20 MPT 136 G 44 420/70 R 28 133 D (136 A8) 405/70 R 20 MPT 136 G 112 A8 (109 B) 46 38 44 420/85 R 28 139 A8 (136 B) 32 440/65 R 28 131 D (134 A8) 425/75 R 20 MPT 148 G 44 440/70 R 28 IND 152 A8 (149 B) 445/65 R 22.5 MPT 160 G AC 70+ 44 480/65 R 28 136 D (139 A8) 50 480/70 R 28 140 D (143 A8) 280/85 R 24 125 D (128 A8) 115 A8 (112 B) 46 32 38 320/70 R 24 116 D (119 A8) 38 540/65 R 28 142 D (145 A8) 122 A8 (119 B) 50 600/65 R 28 147 D (150 A8) 340/85 R 24 125 A8 (122 B) 50 600/65 R 28 154 D (157 A8) 360/70 R 24 122 D (125 A8) 125 A8 (122 B) 380/70 R 24 125 D (128 A8) 380/85 R 24 131 A8 (128 B) 50 32 320/85 R 24 380/70 R 24 50 420/65 R 20 38 600/70 R 28 157 D (160 A8) 46 380/85 R 30 135 A8 (132 B) 38 420/70 R 30 134 D (137 A8) 32/26 32 26 26 50 38 50 420/85 R 30 140 A8 (137 B) 50 405/70 R 24 MPT 149 G 44 460/85 R 30 145 A8 (142 B) 50 420/70 R 24 130 A8 (127 B) 46 480/70 R 30 141 A8 (141 B) 420/70 R 24 130 D (133 A8) 38 480/70 R 30 141 D (144 A8) 420/85 R 24 137 A8 (134 B) 50 540/65 R 30 150 D (153 A8) 440/65 R 24 128 D (131 A8) 149 D (152 A8) 445/70 R 24 MPT 151 G 46 38 34/26 32 600/65 R 30 46 600/70 R 30 152 D (155 A8) 26 32 710/55 R 30 159 D (162 A8) 26 46 710/60 R 30 162 D (165 A8) 26 38 750/55 R 30 162 D (165 A8) 26 480/65 R 24 133 D (136 A8) 480/70 R 24 138 A8 (135 B) 480/70 R 24 138 D (141 A8) general H H G AC C 70 495/70 R 24 MPT 155 G H 44 Page 320/65 R 16 34 Tubeless type, can be used with tubes Tubeless type, can be used with tubes 10 Service description 85 T C Tyre size SS T SV T 65 SV Page AC H H AC 70 AC 70 C 70 H AC 85 Service description AC Tyre size G O O Tractor and harvester tyres agricultural tyres 11 Overview by dimension and profile 150 D (153 A8) 40 T T SS SV T SV AC C H AC AC T SS T SV T SV AC AC C 70 H AC AC AC 650/75 R 32 172 A8 (169 B) 62 520/85 R 38 155 A8 (152 B) 680/85 R 32 173 A8 (170 B) 62 540/65 R 38 147 D (150 A8) AC 70 G 62 580/70 R 38 155 D (158 A8) 680/85 R 32 (CHO) 178 A8 (175 B) C 520/70 R 38 65 62 70 AC 75 G 70 167 A8 (164 B) 70 650/75 R 32 85 Page C Service description 65 Tyre size 70 Page 70 Service description 85 Tyre size 52 34 40 800/65 R 32 167 A8 (164 B) 62 600/65 R 38 153 D (156 A8) 800/65 R 32 172 A8 (169 B) 62 650/65 R 38 157 D (160 A8) 800/65 R 32 178 A8 (175 B) AC 70 N 62 650/75 R 38 169 D (172 A8) 28 28 34/22 28/34/22 800/70 R 32 (CHO) 175 A8 (172 B) 64/58 650/85 R 38 173 D (176 A8) 900/60 R 32 (CHO) 176 A8 (173 B) 26/58 710/70 R 38 900/70 R 32 CHO 182 A8 (179 B) 58 800/70 R 38 (CHO) 178 D (181 A8) 900/70 R 32 188 A8 (185 B) 64/58 900/60 R 38 172 D (175 A8) 1050/50 R 32178 A8 (178 B) 26 900/60 R 38 CHO 178 D (181 A8) 58 380/85 R 34 146 A8 (146 B) 52 480/80 R 42 151 A8 (151 B) 52 420/85 R 34 142 A8 (139 B) 52 520/85 R 42 162 A8 (159 B) 52 420/85 R 34 147 A8 (147 B) 52 650/65 R 42 165 D (168 A8) 460/85 R 34 147 A8 (144 B) 52 650/75 R 42 165 D (168 A8) 28 480/70 R 34 143 A8 (140 B) 46 680/80 R 42 CHO 180 D (183 A8) 58 480/70 R 34 143 D (146 A8) 40 710/70 R 42 173 D (176 A8) 28 520/70 R 34 148 A8 (145 B) 46 710/75 R 42 175 D (178 A8) 28 520/70 R 34 148 D (151 A8) 40 380/90 R 46 149 A8 (146 B) 52 540/65 R 34 145 D (148 A8) 34 380/90 R 46 159 A8 (156 B) 54 600/65 R 34 151 D (154 A8) 166 D (169 A8) 44/28 28/58 28 34/22 34 480/80 R 46 158 A8 (158 B) 52 650/65 R 34 161 D (164 A8) 28 520/85 R 46 158 A8 (155 B) 52 13.6 R 36 127 A8 (124 B) AC 90 52 380/90 R 50 151 A8 (151 B) 52 340/85 R 38 133 A8 (130 B) 52 380/90 R 50 160 A8 (160 B) 54 340/85 R 38 148 A8 (145 B) 54 480/80 R 50 159 A8 (159 B) 52 380/80 R 38 142 A8 (142 B) 52 420/85 R 38 144 A8 (141 B) 52 460/85 R 38 149 A8 (146 B) 52 40 46 480/70 R 38 145 D (148 A8) 520/70 R 38 150 A8 (147 B) general O H H G H H G O Tractor and harvester tyres (continued) Tubeless type, can be used with tubes Tubeless type, can be used with tubes 12 agricultural tyres 13 Overview by dimension and profile Harvester steer wheels and IMP tyres (Radial) general Ag ro -T ra ile G 70 ti- ul M Service Page description MPT IMP 265/70 R 16 MPT 114 G 74 285/84 R 16 MPT 126 G 74 70 425/55 R 17 MPT 134 G 460/70 R 24 IMP 151 A8 68 163 A8 325/70 R 18 MPT 125 G 74 355/60 R 18 MPT 142 J 500/70 R 24 IMP 155 A8 164 A8 365/70 R 18 MPT 132 G 74 500/85 R 24 IMP 158 A8 171 A8 275/80 R 20 MPT 131 G 74 335/80 R 20 MPT 134 G 74 500/80 R 28 IMP • 164 A8 176 A8 375/70 R 20 MPT 136 G 74 405/70 R 20 MPT 136 G 74 600/65 R 28 IMP 156 A8 168 A8 425/75 R 20 MPT 148 G 74 440/50 R 17 IMP 135 D 135 D 500/50 R 17 IMP • 149 D 149 D • 70 • • • • 68 540/65 R 30 IMP 156 A8 168 A8 620/70 R 30 IMP 166 A8 178 A8 500/85 R 34 IMP • 166 D 178 D • 68 68 • 164 A8 176 A8 • 500/85 R 30 IMP Tubeless type, can be used with tubes 14 Tyre size AC Se rv i d ro un G Al l- 65 SV AC T 70 G Service Page description AC Tyre size r ce MPT tyres (Radial) 68 68 • 68 68 74 74 445/65 R 22.5 MPT 160 G 74 AC 70 + 405/70 R 24 MPT 149 G 76 445/70 R 24 MPT 151 G 76 495/70 R 24 MPT 155 G 76 Tubeless type, can be used with tubes 68 drive wheel free rolling agricultural tyres 15 Overview by dimension and profile Tractor cross-ply steering tyres Tyre sizePR 84 7.5 L - 15 6 80 6.50 - 16 8 80 7.50 - 16 8 8.3 - 24 6 80 T Page 4.00 – 16 4 4.50 – 16 4 84 5.00 – 16 4 84 6.00 – 16 6 84 6.50 – 16 6 84 7.50 – 16 6 84 9.5 - 24 8 7.50 – 16 8 84 11.2 - 24 8 80 12.4 - 24 8 14.9 - 24 8 Tube type 14.9/80 - 24 general C Fa rm er A S Fa rm er A Page AS - 9 Tyre size PR Fa rm er Tractor cross-ply tyres 80 80 80 80 12 80 80 8.3 - 28 8 11.2 - 28 8 12.4 - 28 6 9.5 - 30 6 16.9 - 30 8 82 8.3 - 32 6 82 80 80 82 6 82 9.5 - 32 12.4 - 32 6 82 16.9 - 34 8 82 18.4 - 34 8 8.3 - 36 82 4 82 9.5 - 36 6 82 9.5 - 36 10 82 9.5 - 42 10 82 Tube type Tubeless type, can be used with tubes 16 agricultural tyres 17 7.00 - 12 8.00 - 12 10.0/75 - 12 11.0/65 - 12 28x9.00 - 15 240/70 - 15 10.0/75 - 15.3 11.5/80 - 15.3 4.00 - 16 6.00 - 16 230/70 - 16 270/75 - 16 15.0/55 - 17 500/40 - 17 320/80 - 18 360/80 - 20 400/70 - 20 15.5/80 - 24 15.5/80 - 24 16.5/85 - 24 9 15 M 30 AC 3 B 3 M general W Fa rm er A er -F AW 55 T IMP 11x7 - 4 4.00 - 8 ar m /2 A Sp S-F ec ar . m Service Page description AS - Tyre size Fa rm er er IMP / MPT tyres (Cross-ply) T Fa rac rm tio er n- Overview by dimension and profile 88 4 PR 2 PR 4 PR 6 PR 6 PR 6 PR 8 PR 6 PR 115 A 8 (8 PR) 8 PR 10 PR 8 PR, 12 PR 10 PR 2 PR 6PR 106 A 8 (10 PR) 119 A 8 101 A 8 (6 PR) 114 A 8 10 PR 12 PR 127 A 8 (10 PR) 140 A 8 126 A 8 (10 PR) 139 A 8 128 A 8 (8 PR) 141 A 8 142 A 8 (14 PR) 154 A 6 145 A 6 (12 PR) 157 A 8 152 A 6 (16 PR) 164 A 6 153 A 6 (14 PR) 165 A 6 88 88 88 88 88 88 94 94 • 88 88 88 88 • 88 • 88 88 • 88 • 90 • 90 • 90 • 90 • 90 • 90 MPT 275/80-18 MPT 10.5-18 MPT 275/80-20 MPT 10.5-20 MPT 335/80-20 MPT 12.5-20 MPT 365/80-20 MPT 14.5-20 MPT 92 123 E (8 PR) 92 • 129 E (10 PR) 92 • 132 E (10 PR) Tubeless type, can be used with tubes Tube type 18 • 126 E ( 10 PR) 92 • drive wheel free rolling agricultural tyres 19 SilentSpeedTyre (SST) kW hp 3 Road performance Economy* *Based on: rolling resistance, mileage, traction and gentle ground handling Traction 88 110 132 162 191 >220 120 150 180 220 260 >300 Noise reducing radial tyre for fast, comfortable and impressively quiet road use Driving comfort qNoise reduction of up to 6 dB(A) in the cab maximises concentration and minimises stress Grassland suitability Driving stability Standard SST Transportation capability Gentle ground handling Load capacity q New casing construction ensures a cost saving through reduced rolling resistance, long tyre life and high damage resistance q Highest levels of productivity achieved through the excellent characteristics of the 65 series profile and casing q Highest possible sustained speed capability of up to 70 km/h (43 mph) Mileage 77.0 65% wide tyre, market standard 76.0 The SilentSpeedTyre SST traction tyre prevents the occurrence of the so-called “booming noise effect“. The SST reduces the noise level in the driver‘s cab by 3 to 6 dB(A) compared with conventional rear axle tyres. SST 75.0 noise level in dB(A) SST 66 90 tractor SST [Wide tyre with 65% aspect ratio, approved for speeds up to 70 km/h - 43 mph] Exceptionally quiet, very comfortable ride, high load capacity and exceptional traction in the field make this a flagship tyre for very demanding use. 44 60 SilentSpeedTyre (SST) Suitability of the SST in the field and on the road Field performance 7 22 30 74.0 – 3 to – 6 db(A) 73.0 72.0 71.0 70.0 69.0 40 42 44 46 48 50 52 54 speed in km/h 20 20 21 SilentSpeedTyre (SST) Technical data Load capacities Tyre size PermittedWidth Outer Static Rolling Speed Service rims* diameterloaded circum- radius description radius ference index LI/SS (mm)(mm)(mm)(mm) 600/65 R 38 W 18 L591 153 D (156 A8) DW 18 L 591 1746 782 5215 825 W 16 L 571 Tyre load capacity (kg) at tyre pressure (bar) 0,4 0,6 0,8 1,0 1,2 1,4 1,6 2,0 2,4 3,0 650/65 R 38 157 D (160 A8) W 18 L6231822 8105420 875 DW 20 B 643 650/65 R 42 165 D (168 A8) W 18 L6161930 8705790 925 DW 20 B 636 Speed (km/h) 3050 3355 3650 3205 3525 3835 3340 3675 4000 3510 3860 4200 4275 4695 51105475 3450 3790 4125 3625 3980 4330 3780 4150 4500 3970 4360 4745 4830 5310 5775 6190 3310 3615 3940 42504765 5150 31253475 3795 4140 44655005 5410 28753260362539604315462552205600 30153425380541604530489054805925 3145367541704635506555155950667572107725 65 50 40 30 10 65 50 40 30 10 tractor SST 2795 2640 2935 2425 2755 3060 2545 2890 3210 2655 310035203910 3155 2985 3315 2740 3110 3455 2880 3270 3630 3000 3505 3980 4420 SST 65 50 40 30 10 * More permitted rims on request Load values given for 0,4 bar and for 0,6 bar at 40 km/h are for calculating dual and triple load values only. All load values are for maximum indicated speeds at low torque. 30 km/h (up to 40 km/h) load values also apply for low-speed high-torque field work. For plowing with single driven tires in the furrow, a minimum inflation pressure of 0,8 bar is required. For intensive road transport at 65/50/40/30 km/h the pressure must be increased by 0,4 bar. Maximum inflation pressure should never be exceeded. All load-speed-pressure data is valid for ground slopes up to and including 20%. When operating on slopes greater than 20%, please, contact Mitas. 22 agricultural tyres 23 SuperVolumeTyre (SVT) Suitability of the SVT in the field and on the road [approved for speeds up to 50 or 70 km/h - 31 or 43 mph respectively] Field performance 7 3 Road performance Economy* In the field the tyre delivers maximum performance through highest load capacity and low inflation pressure – on the road it provides driving stability and offers enormous transportation capabilities. Traction Driving stability SVT 66 90 88 110 132 162 191 >220 120 150 180 220 260 >300 SuperVolumeTyre (SVT) for powerful machines with maximum load capacity and driving comfort qDeveloped for use on powerful tractors (>180 hp) and harvesters q Extremely large volume of air guarantees gentle ground handling, combined with very high load capacity and lowest possible inflation pressure ensuring the highest yields Standard Transportation capability Gentle ground handling Load capacity q Maximum traction thanks to largest possible ground contact patch and very high mileage with speeds up to 70 km/h (43 mph) makes the SVT very economical Mileage SVT Standard 24 24 44 60 Driving comfort Grassland suitability *Based on: rolling resistance, mileage, traction and gentle ground handling 22 30 tractor SVT kW hp SVT The extremely large volume of air means maximum load capacity with lowest possible tyre pressure – this adds up to optimum ground protection, even with the heaviest of equipment. 25 SuperVolumeTyre (SVT) Technical data Load capacities Tyre size PermittedWidth Outer Static Rolling Speed Service rims* diameterloaded circum- radius description radius ference index LI/SS (mm)(mm)(mm)(mm) 540/65 R 28 W 16 L 540 W 18 L 560 1414 627 4210 675 142 D (145 A8) W 15 L 540 600/65 R 28 W 18 L606 1494 6644444 700 DW 20 B 626 154 D (157 A8) Tyre load capacity (kg) at tyre pressure (bar) Speed 0,4 0,6 0,8 1,0 1,2 1,4 1,6 2,0 2,4 2,8 (km/h) 2210 2385 2530 2650 65 2110 2320 2505 2655 2785 50 1960 2200 2420 2615 2770 2900 40 2060 2315 2540 2745 2910 3050 30 2165 2505 2815 3095 3340 3545 3710 3975 10 2605 2815 2995 3150 3490 3750 65 2490 2737 2955 3145 3310 3665 3940 50 2310 2595 2855 3080 3280 3450 3820 4125 40 2425 2725 2995 3235 3445 3625 4010 4315 30 2555 2955 3320 3650 3940 4195 4410 4885 5250 5625 10 2900317533803550 39004125 65 2730 3045333535503730 40954330 50 2505 2850 3175348037003875 42704500 40 2630 2990 3335365538854085 44854745 30 2730 3200 3640 4060445047304970 54605775 6190 10 2280246526052725 30803350 65 2180 2395258527352860 32353520 50 2020 2270 2495269528553000 33753650 40 2125 2385 2620283030003135 35453855 30 2235 2585 2905 3190345036503815 43154690 5025 10 2985 3270 3430 3550 65 2815 3135 3435 3605 3730 50 2575 2935 3270 3585 3755 3875 40 2705 3080 3435 3765 3945 4085 30 2810 3295 3750 4180 4580 4805 4970 5325 10 2805306533653650 40454375 65 2655 2945322035303835 42504595 50 2440 2765 3075336036804000 44304750 40 2560 2905 3230352538654200 46555030 30 2670 3115 3540 3930429547105110 46656125 6565 10 3035 3315 3605 3875 4385 4750 65 2870 3185 3480 3785 4070 4605 4990 50 2635 2990 3325363039454250 48005150 40 2770 3140 3490381541454455 50405465 30 2885 3370 3825 4250464550455425 61356650 7125 10 3060334036754000 44004750 65 2890 3210351038604200 46204990 50 2655 3015 3350366040254375 48205150 40 2790 3165 3515384542254600 50605465 30 2905 3395 3855 4280468051455600 61606650 7125 10 4180 4575 5010 5450 5965 6300 50 3815 4235 4590502555056000 65556900 40 4085 4530 4915538058956420 70157385 30 4235 4700 5095558061156600 72757660 25 4695 5210 5650618067757380 80608485 20 4960 5505 5970653571607800 8520897010350 10 4250 4650 5020 5450 5950 6500 50 3890 4315 4670511055156000 65357100 40 4165 4615 5000546559006420 69957595 30 4320 4790 5185567061206660 72557880 25 4790 5305 5745628567857380 80408735 20 5060 5610 6070664071707800 8495923010650 10 5045 5515 5955 6500 7055 7500 50 4200 4655 5045551559556500 70557500 40 4495 4985 5395590063706955 75508025 30 4665 5170 5595612066107215 78308325 25 5170 5730 6200678573207995 86809225 20 5465 6055 6555717077408450 9175975011250 10 600/70 R 28 W 18 L 627 1574 6964660 725 DW 20 B 647 157 D (160 A8) W 16 L 548 540/65 R 30 W 18 L 558 1487 668 4435 700 150 D (153 A8) W 15 L 540 600/70 R 30 W 18 L625 1595 7004700 750 152 D (155 A8) DW 20 B 645 710/55 R 30 159 D (162 A8) DW 23 B 6901500 6744475 725 710/60 R 30 162 D (165 A8) DW 23 B 7081646 7304870 750 750/55 R 30 162 D (165 A8) DW 23 B 7201584 7124725 750 800/70 R 32 175 A8 (172 B) DW 25 B 762 1932 8455630 875 DW 27 B 784 900/60 R 32 DW 27 B 857 1905 8505700 925 176 A8 (173 B) DW 30 B 890 1050/50 R 32 36.00 VA 10151890 8555640 875 178 A8 (178 B) tractor SVT SVT * More permitted rims on request 26 agricultural tyres 27 SuperVolumeTyre (SVT) Technical data Load capacities Tyre size PermittedWidth Outer Static Rolling Speed Service rims* diameterloaded circum- radius description radius ference index LI/SS (mm)(mm)(mm)(mm) Tyre load capacity (kg) at tyre pressure (bar) Speed 0,4 0,6 0,8 1,0 1,2 1,4 1,6 2,0 2,4 2,8 (km/h) 3215 3475 3690 3875 4305 4625 65 3070 3375 3645 3875 4070 4520 4855 50 2850 3205 3520 3800 4040 4250 4710 5000 40 2995 3365 3695 3995 4245 4455 4950 5320 30 3150 3645 4095 4500 4860 5165 5425 6025 6475 6940 10 3380 3655 3905 4125 65 3230 3550 3835 4100 4330 50 3000 3370 3705 4000 4275 4500 40 3150 3540 3890 4200 4490 4745 30 3315 3835 4310 4735 5115 5465 5775 6190 10 3990 4375 4645 4875 5425 5800 65 37604190 4590 4880 5120 5695 6090 50 3445 39204370 4790 5085 5300 5940 6300 40 3620 41204590 5030 5340 5605 6235 6670 30 3760 4405 5015 5585 6125 6505 6825 7590 8120 8700 10 4465 4895 5195 5450 6075 6500 65 4210 4690 5140 5455 5725 6375 6825 50 3855 4390 4890 5360 5690 6000 6650 7100 40 4050 4610 5135 5630 5975 6270 6985 7475 30 4210 4930 5610 6250 6855 7275 7630 8500 9100 9750 10 4305 4720 5030 5300 65 4055 4520 4955 5280 5565 50 3715 4230 4715 5170 5510 5800 40 3905 4445 4950 5425 5785 6095 30 4055 4750 5410 6025 6605 7045 7420 7950 10 5190 5690 6070 6400 7035 7500 65 48905450 5975 6375 6720 7390 7875 50 4480 51005685 6230 6650 7000 7705 8250 40 4705 53605970 6545 6980 7360 8090 8625 30 4890 5730 6525 7270 7965 8500 8960 9850 10500 11250 10 4875 5325 5825 6300 65 46105120 5595 6115 6615 50 4235 48055340 5835 6375 6900 40 4450 50505605 6125 6695 7245 30 4635 5415 6145 6825 7460 8155 8820 9450 10 4875 5325 5825 6300 6985 7500 65 46105120 5595 6115 6615 7335 7875 50 4235 48055340 5835 6375 6900 7650 8250 40 4450 50505605 6125 6695 7245 8035 8625 30 4635 5415 6145 6825 7460 8155 8820 9780 10500 11250 10 4175 4575 4885 5150 65 39354380 4805 5125 5410 50 3605 41004570 5010 5345 5600 40 3785 43054800 5260 5615 5925 30 3935 4605 5245 5845 6405 6835 7210 7725 10 4500 4935 5285 5600 6100 6500 65 42454725 5180 5550 5880 6405 6825 50 3885 44254930 5405 5790 6150 6680 7100 40 4080 46455180 5675 6080 6440 7015 7475 30 4240 4970 5655 6305 6910 7400 7840 8540 9100 9750 10 4785 5245 5640 6000 6480 6900 65 45105025 5510 5925 6300 6805 7245 50 4130 47005240 5745 6175 6500 7095 7500 40 4340 49405505 6030 6490 6900 7450 7935 30 4510 5280 6010 6700 7345 7900 8400 9070 9660 10350 10 650/65 R 38 W 18 L 645 1828 8105445 875 157 D (160 A8) DW 20 B 660 DW 21 B 667 650/75 R 38 DW 20 B 657 1944 872 5795 925 169 D (172 A8) DW 23 B 687 DW 23 B 720 650/85 R 38 DW 20 B 688 2070 920 6130 975 173 D (176 A8) DW 21 B 699 710/70 R 38 DW 23 B 7361958 8705780 925 166 D (169 A8) 800/70 R 38 178 D (181 A8) DW 25 B765 2052911 6090975 DW 27 B 787 900/60 R 38 172 D (175 A8) DW 27 B870 DW 30 B 900 2060918 6115975 900/60 R 38 172 D (175 A8) DW 27 B870 DW 30 B 900 2060918 6115975 DW 21 B 650 650/75 R 42 DW 20 B 640 2035 905 6090 975 165 D (168 A8) DW 23 B 670 710/70 R 42 DW 23 B731 2070935 6150975 173 D (176 A8) DW 25 B 751 710/75 R 42 175 D (178 A8) DW 23 B751 2171 97164601025 DW 25 B 771 tractor SVT 650/65 R 34 W 18 L 654 1719 7695116 825 161 D (164 A8) DW 20 B 664 SVT * More permitted rims on request All load-speed-pressure data is valid for ground slopes up to and including 20%. When operating on slopes greater than 20%, please, contact Mitas. Load values given for 0,4 bar and for 0,6 bar at 40 km/h are for calculating dual and triple load values only. All load values are for maximum indicated speeds at low torque. oad-pressure data for Load&Carry applications apply to low-torque transport operations at max. speeds of L 10 km/h and for a max. distance of 800 meters before discharging the load and returning empty. 30 km/h (up to 40 km/h) load values also apply for low-speed high-torque field work. For plowing with single driven tires in the furrow, a minimum inflation pressure of 0,8 bar is required. For intensive road transport at 65/50/40/30 km/h the pressure must be increased by 0,4 bar. Maximum inflation pressure should never be exceeded. 28 agricultural tyres 29 65 Series wide tyre – AC 65 Suitability of the AC 65 in the field and on the road [Wide tyre with 65% aspect ratio, approved for speeds up to 70 km/h - 43 mph] Field performance 7 3 Road performance Economy* High load capacity and high mileage mean the AC 65 is an economical all-rounder on the road and in the field. *Based on: rolling resistance, mileage, traction and gentle ground handling Traction Driving comfort Grassland suitability Driving stability 66 90 88 110 132 162 191 >220 120 150 180 220 260 >300 qVery gentle ground handling in the field and on grassland, thanks to the tyre‘s exceptional load capacities and the very large ground contact patch AC 65 Transportation capability Gentle ground handling Mileage q q q Very comfortable on the road at high speeds up to 70 km/h (43 mph) Very high transportation capability through large volume of air Extremely economical, thanks to very good traction and low-wear tread compound AC 65 Standard tyre 30 30 44 60 AC 65 Powerful wide tyre for all-round applications, delivering efficiency in the field and on the road Standard Load capacity 22 30 tractor AC 65 kW hp Wide tyre AC 65 The very large ground contact patch permits gentle ground handling, even with heavy equipment. 31 65 Series wide tyre – AC 65 Technical data Load capacities Tyre size PermittedWidth Outer Static Rolling Speed Service rims* diameterloaded circum- radius description radius ference index LI/SS (mm)(mm)(mm)(mm) 320/65 R 16 W 10316 W 9 310844373 2497390 117 D (120 A8) W 11 326 Tyre load capacity (kg) at tyre pressure (bar) Speed 0,4 0,6 0,8 1,0 1,2 1,4 1,6 2,0 2,4 3,0 (km/h) 440/65 R 24 W 14 L445 W 13 4351196 5433585 575 128 D (131 A8) W 12 425 480/65 R 24 W 15 L473 133 D (136 A8) W 14 L 463 1256 570 3764 600 W 13 453 540/65 R 24 W 16 L523 140 D (143 A8) W 18 L 543 1317 590 3922 625 W 15 L 513 540/65 R 24 W 16 L523 146 D (149 A8) W 18 L 543 1317 590 3922 625 W 15 L 513 440/65 R 28 W 14 L447 W 13 4371292 5943896 625 131 D (134 A8) W 12 427 480/65 R 28 W 15 L475 136 D (139 A8) W 14 L 465 1355 616 4064 650 W 13 455 540/65 R 28 W 16 L530 142 D (145 A8) W 18 L 550 1410 624 4145 675 W 15 L 520 600/65 R 28 W 18 L590 147 D (150 A8) DW 18 L 590 1485 661 4411 700 W 16 L 570 715 800 890 975 1135 1285 65 655 750 840 935 1025 2295 1350 50 585 685 780 880 975 1060 1245 1400 40 615 715 820 920 1020 1120 1305 1480 30 625 750 875 1000112512451365 15901800 1930 10 1225 1355 1500 1650 65 1145 1285 1420 1575 1735 50 1045 1195 1340 1480 1645 1800 40 1095 1255 1410 1555 1725 1900 30 1130 1335 1530 1715 1895 2100 2310 2475 10 1400 1530 1670 1800 65 1325 1470 1610 1750 1890 50 1215 1380 1535 1675 1830 1950 40 1280 1450 1610 1760 1920 2070 30 1330 1555 1765 1960 2145 2335 2520 2700 10 1605 1755 1910 2060 65 1515 1685 1840 2005 2165 50 1395 1580 1755 1920 2090 2240 40 1465 1660 1845 2015 2195 2370 30 1525 1780 2020 2245 2455 2675 2885 3090 10 1930 2110 2310 2500 65 1825 2025 2215 2425 2625 50 1675 1900 2115 2310 2525 2725 40 1760 1995 2220 2425 2655 2875 30 1835 2140 2430 2700 2950 3230 3500 3750 10 1930 2110 2310 2500 2780 3000 65 1825 2025 2215 2425 2625 2915 3150 50 1675 1900 2115 2310 2525 2740 3040 3250 40 1760 1995 2220242526552875 31953450 30 1835 2140 2430 2700295032303500 38904200 4500 10 1505 1645 1800 1950 65 1425 1580 1725 1890 2050 50 1305 1485 1650 1800 1970 2120 40 1375 1560 1730 1890 2070 2245 30 1430 1670 1895 2110 2305 2520 2730 2925 10 1720 1880 2060 2240 65 1625 1805 1975 2165 2350 50 1495 1695 1885 2060 2260 2430 40 1570 1780 1980 2160 2370 2575 30 1635 1910 2165 2410 2630 2885 3135 3360 10 2065 2255 2455 2650 65 1950 2165 2365 2580 2785 50 1790 2035 2260 2470 2690 2900 40 1880 2135 2375 2595 2825 3050 30 1960 2290 2600 2890 3155 3440 3710 3975 10 2430 2660 2875 3075 65 2300 2555 2790 3020 3230 50 2110 2395 2665 2910 3145 3350 40 2220 2515 2795 3055 3305 3535 30 2310 2700 3065 3405 3720 4025 4305 4615 10 tractor AC 65 420/65 R 20 W 13415 W 12 4051050 4693146 500 125 D (128 A8) W 11 395 AC 65 * More permitted rims on request 32 agricultural tyres 33 65 Series wide tyre – AC 65 Technical data Load capacities Tyre size PermittedWidth Outer Static Rolling Speed Service rims* diameterloaded circum- radius description radius ference index LI/SS (mm)(mm)(mm)(mm) 540/65 R 30 W 16 L526 150 D (153 A8) W 18 L 546 1485 664 4419 700 W 15 L 516 Tyre load capacity (kg) at tyre pressure (bar) Speed 0,4 0,6 0,8 1,0 1,2 1,4 1,6 2,0 2,4 3,0 (km/h) 540/65 R 34 W 16 L526 145 D (148 A8) W 18 L 546 1580 709 4709 750 W 15 L 516 600/65 R 34 W 18 L592 151 D (154 A8) DW 18 L 592 1648 737 4904 775 W 16 L 572 540/65 R 38 W 16 L517 147 D (150 A8) W 18 L 537 1678 760 5023 800 W 15 L 507 600/65 R 38 W 18 L590 153 D (156 A8) DW 18 L 590 1759 792 5251 825 W 16 L 570 650/65 R 38 157 D (160 A8) W 18 L6181828 8105416 875 DW 20 B 638 DW 23 B 710/70 R 38 ) DW 25 B 166 D (169 A8 650/65 R 42 165 D (168 A8) 7081925 8575716 925 728 DW 20 B6411936 8605798 925 DW 18 L 621 2130 2325 2545 2725 3080 3350 65 2010 2235 2440 2675 2860 3235 3520 50 1850 2100 2330 2545 2790 3000 3375 3650 40 1940 2205 2450267529303135 35453855 30 2020 2365 2680 2980325535653815 43154690 5025 10 2505 2740 3000 3250 65 2370 2630 2875 3150 3415 50 2175 2470 2745 3000 3285 3550 40 2285 2595 2880 3150 3450 3740 30 2380 2780 3160 3510 3835 4200 4550 4875 10 2255 2465 2690 2900 65 2130 2370 2590 2820 3045 50 1960 2225 2470 2700 2945 3150 40 2055 2335 2595 2835 3090 3335 30 2145 2505 2845 3160 3450 3765 4060 4350 10 2650 2900 3180 3450 65 2505 2785 3045 3335 3625 50 2300 2615 2905 3175 3480 3780 40 2420 2745 3050 3330 3655 3970 30 2520 2945 3340 3710 4055 4450 4830 5175 10 2380 2600 2845 3075 65 2250 2500 2730 2985 3230 50 2065 2345 2605 2850 3115 3350 40 2170 2465 2735 2990 3270 3535 30 2260 2640 3000 3330 3640 3980 4305 4615 10 2795 3050 3355 3650 65 2640 2935 3205 3525 3835 50 2425 2755 3060 3340 3675 4000 40 2545 2890 3210 3510 3860 4200 30 2655 3100 3520 3910 4275 4695 5110 5475 10 3155 3450 3790 4125 65 2985 3315 3625 3980 4330 50 2740 3110 3455 3780 4150 4500 40 2880 3270 3630 3970 4360 4745 30 3000 3505 3980 4420 4830 5310 5775 6190 10 3975 4345 4825 5300 65 3755 4175 4565 5065 5565 50 3445 3915 4350 4760 5280 5800 40 3620 4110 4570 5000 5550 6095 30 3765 4405 5005 5565 6085 6755 7420 7950 10 3310 3615 3940 4250 4765 5150 65 3125 3475 3795 4140 4465 5005 5410 50 2875 3260 3625 3960 4315 4625 5220 5600 40 3015 3425 3805 4160 4530 4890 5480 5925 30 3145 3675 4170 4635506555155950 66757210 7725 10 tractor AC 65 600/65 R 30 W 18 L590 149 D (152 A8) DW 18 L 590 1549 687 4591 725 W 16 L 570 AC 65 * More permitted rims on request Load values given for 0,4 bar and for 0,6 bar at 40 km/h are for calculating dual and triple load values only. or intensive road transport at 65/50/40/30 km/h the pressure must be increased by 0,4 bar. F Maximum inflation pressure should never be exceeded. All load values are for maximum indicated speeds at low torque. All load-speed-pressure data is valid for ground slopes up to and including 20%. When operating on slopes greater than 20%, please, contact Mitas. 30 km/h (up to 40 km/h) load values also apply for low-speed high-torque field work. For plowing with single driven tires in the furrow, a minimum inflation pressure of 0,8 bar is required. 34 agricultural tyres 35 70 Series wide tyre – HC 70 kW hp 3 Road performance Economy* Traction Driving comfort Grassland suitability *Based on: rolling resistance, mileage, traction and gentle ground handling Driving stability HC 70 Transportation capability Load capacity HC 70 36 36 88 110 132 162 191 >220 120 150 180 220 260 >300 The new all-round benchmark in the 70 series wide tyre segment with higher load capacities then conventional 70 series qLow operating costs thanks to minimised slip, plus gentle ground handling through high load capacity Standard Gentle ground handling 66 90 tractor HC 70 [Wide tyre approved for speeds up to 65 km/h - 40 mph] Gentle handling of fields and grassland, powerful performance on the road – the high load capacity of the HC 70 is a clear benefit in all applications. 44 60 HC 70 Suitability of the HC 70 in the field and on the road Field performance 7 22 30 q q Comfortable, safe road performance, thanks to wide tyre shoulders Particularly gentle handling of grassland through rounded shoulder design and lug edges. Mileage Low track depth and low operating costs, thanks to reduced inflation pressure and good traction Reduction in track depth by reduced air pressure of 0,3 bar 0,3 bar 37 70 Series wide tyre – HC 70 Technical data Load capacities Tyre size PermittedWidth Outer Static Rolling Speed Service rims* diameterloaded circum- radius description radius ference index LI/SS (mm)(mm)(mm)(mm) Tyre load capacity (kg) at tyre pressure (bar) Speed 0,60,81,01,21,41,62,0(km/h) 65 1250 1140 1035 945 50 1315 1200 1085 990 890 40 1360 1250 1190 1035 930 820 30 1440 1315 1445 1085 975 860 10 1750 1875 1600 2170 1320 1190 1045 65 1500 1370 1235 1130 50 1575 1435 1295 1185 1065 40 1650 1500 1355 1235 1110 980 30 1725 1575 1420 1300 1170 1030 10 2100 2250 1915 1730 1580 1420 1250 65 1650 1495 1340 1225 50 1735 1570 1410 1290 1160 40 1800 1640 1470 1345 1210 1065 30 1900 1720 1545 1410 1270 1115 10 2310 2475 2095 1880 1720 1545 1360 65 1900 1735 1565 1430 50 1995 1820 1645 1505 1350 40 2060 1900 1715 1570 1410 1240 30 2185 1995 1800 1645 1480 1305 10 2660 2850 2425 2190 2005 1805 1585 65 2360 2145 1930 1765 50 2480 2250 2025 1850 1665 40 2575 2350 2110 1930 1735 1530 30 2715 2465 2220 2030 1825 1605 10 3305 3540 3000 2700 2470 2220 1955 65 1750 1600 1445 1320 50 1840 1675 1515 1385 1245 40 1900 1750 1580 1445 1300 1145 30 2015 1835 1660 1520 1365 1200 10 2450 2625 2335 2020 1850 1660 1465 65 2060 1870 1680 1535 50 2165 1965 1765 1615 1450 40 2240 2050 1840 1685 1515 1335 30 2370 2150 1935 1770 1590 1400 10 2885 3090 2620 2355 2150 1935 1705 65 2500 2285 2065 1890 50 2625 2395 2170 2980 1780 40 2725 2500 2260 2065 1860 1635 30 2875 2625 2375 2170 1950 1720 10 3500 3750 3195 2890 2645 2375 2090 2120 1930 1735 1590 65 2225 2025 1825 1670 1500 50 2110 1905 1740 1565 1375 40 2300 2220 2000 1825 1645 1445 30 2440 2700 2430 2225 2000 1760 10 2970 3180 65 2575 2355 2130 1950 50 2705 2470 2235 2045 1840 40 2800 2580 2335 2135 1920 1690 30 2960 2705 2450 2240 2015 1775 10 3605 3865 3295 2985 2725 2455 2160 W 10 W 11 W9 325 335 315 1115 491 3295 525 360/70 R 24 122 D (125 A8) W 11 W 12 W 10 365 375 355 1142 508 3398 550 380/70 R 24 125 D (128 A8) W 12 W 13 W 11 395 405 385 1191 533 3545 575 420/70 R 24 130 D (133 A8) W 13 W 14 L W 12 443 453 433 1245 552 3695 600 480/70 R 24 138 D (141 A8) W 15 L W 16 L W 14 L 502 512 492 1320 574 3896 625 380/70 R 28 127 D (130 A8) W 12 W 13 W 11 395 405 385 1292 576 3850 625 420/70 R 28 133 D (136 A8) W 13 W 14 L W 12 438 448 428 1350 610 4038 650 480/70 R 28 140 D (143 A8) W 15 L W 16 L W 14 L 498 508 488 1422 630 4220 675 420/70 R 30 134 D (137 A8) W 13 W 14 L W 12 433 443 423 1392 622 4150 675 480/70 R 30 141 D (144 A8) W 15 L W 16 L W 14 L 499 509 489 1474 655 4380 700 tractor HC 70 320/70 R 24 116 D (119 A8) HC 70 * More permitted rims on request 38 agricultural tyres 39 70 Series wide tyre – HC 70 Technical data Load capacities Tyre size PermittedWidth Outer Static Rolling Speed Service rims* diameterloaded circum- radius description radius ference index LI/SS (mm)(mm)(mm)(mm) Tyre load capacity (kg) at tyre pressure (bar) Speed 0,60,81,01,21,41,62,0(km/h) 65 2725 2495 2260 2065 50 2860 2620 2375 2170 1950 40 3000 2730 2475 2265 2035 1790 30 3135 2870 2600 2375 2135 1880 10 3815 4090 3490 3165 2895 2600 2290 65 3150 2850 2555 2335 50 3310 2995 2680 2450 2205 40 3450 3120 2795 2555 2300 2025 30 3625 3280 2935 2685 2415 2125 10 4410 4725 3990 3575 3270 2940 2590 65 2900 2645 2385 2180 50 3045 2775 2505 2290 2060 40 3150 2895 2615 2390 2150 1890 30 3335 3040 2745 2510 2255 1985 10 4060 4350 3700 3340 3055 2745 2420 65 3350 3020 2695 2460 50 3520 3170 2825 2585 2325 40 3650 3305 2950 2695 2525 2135 30 3855 3470 3095 2830 2545 2240 10 4690 5025 4225 3770 3445 3100 2730 65 3875 3530 3180 2910 50 4070 3705 3340 3055 2745 40 4250 3865 3480 3185 2865 2520 30 4455 4055 3655 3345 3005 2645 10 5425 5815 4940 4450 4070 3660 3225 W 15 L W 16 L W 14 L 494 504 484 1590 704 4710 750 520/70 R 34 148 D (151 A8) W 16 L W 18 L W 15 L 539 559 529 1651 735 4905 775 480/70 R 38 145 D (148 A8) W 15 L W 16 L W 14 L 496 506 486 1699 768 5082 800 520/70 R 38 150 D (153 A8) W 16 L W 18 L W 15 L 536 556 524 1751 790 5232 825 580/70 R 38 155 D (158 A8) W 18 L 596 1857 822 5500 875 tractor HC 70 480/70 R 34 143 D (146 A8) HC 70 * More permitted rims on request Load values given for 0,4 bar and for 0,6 bar at 40 km/h are for calculating dual and triple load values only. All load values are for maximum indicated speeds at low torque. 30 km/h (up to 40 km/h) load values also apply for low-speed high-torque field work. For plowing with single driven tires in the furrow, a minimum inflation pressure of 0,8 bar is required. or intensive road transport at 65/50/40/30 km/h the pressure must be increased by 0,4 bar. F Maximum inflation pressure should never be exceeded. ll load-speed-pressure data is valid for ground slopes up to and including 20%. A When operating on slopes greater than 20%, please, contact Mitas. 40 agricultural tyres 41 70 Series wide tyre – AC 70 G Suitability of the AC 70 G in the field and on the road [Wide tyre with 70% aspect ratio, approved for speeds up to 50 km/h (31 mph) or 90 km/h (56 mph) in the MPT range] Field performance 7 3 Road performance Economy* The tread design of the AC 70 G makes it ideally suited for handling grassland and for road use. *Based on: rolling resistance, mileage, traction and gentle ground handling Traction 66 90 88 110 132 162 191 >220 120 150 180 220 260 >300 AC 70 G Wide grassland tyre with optimum road characteristics Driving stability qThe large, wide lug areas protect ground and plants q Stable, safe and comfortable running on the road, thanks to a wide tread area and large lug overlap in the tread centre Standard Transportation capability Gentle ground handling Load capacity AC 70 G 44 60 Driving comfort Grassland suitability AC 70 G 22 30 tractor AC 70 G kW hp q q Economical thanks to low wear Tyres in the MPT range have a special casing and steel belt for high speeds (90 km/h / 56 mph) Mileage Large, wide lug areas mean quiet running on the road and gentle driving over grassland. conventional profile design AC 70 G Tread pattern 42 42 43 70 Series wide tyre – AC 70 G Technical data Load capacities Tyre size PermittedWidth Outer Static Rolling Speed Service rims* diameterloaded circum- radius description radius ference index LI/SS (mm)(mm)(mm)(mm) Tyre load capacity (kg) at tyre pressure (bar) Speed 0,60,81,01,21,41,62,02,53,03,54,04,56,0 (km/h) 460510570630740880 1030 118090 490560620680800960 1120 128065 510 570 640 700 830100011601320 50 460520590650720850 1020 1190 136040 430500570640710780930 1110 1300 148030 610 720 820 920103011301330160018602120 10 570 650 720 790 93011101280145017002) 90 620 700 780 860101012001390157018402) 65 640 720 800 880104012401430162019002) 50 580660740820910 1070 1270 1470 1670 19502) 40 540630720810900990 1170 1380 1600 1810 21202) 30 770 9001030116012901420168019902300261030602) 10 780 880 98010801280155018302120 90 850 960107011701390168019902300 65 880 990110012101430174020502370 50 790 9001020113012401470178021002440 40 740 860 9801110123013501600194022902650 30 1060124014101590177019402300279032903820 10 660 740 820 9001060126014601650 90 710 800 890 9801150137015801790 65 740 830 92010101200141016301850 50 660 760 850 95010401230146016801900 40 620 720 820 930103011301340157018202060 30 890104011801330148016301920227026202970 10 790 890 98010801280152017602000 90 860 960107011701380165019102170 65 880 990110012101440170019702240 50 790 9101020113012501470175020202300 40 740 860 9901110123013601600190022002500 30 1060124014201600177019502300273031703600 10 600 670 750 820 970116013401510169019503) 90 3) 650 730 810 890106012501450164018302120 65 670 760 840 9201090129015001690189021803) 50 600 690 780 860 9501120133015401730194022403) 40 3) 560 660 750 840 9401030122014401670189021102440 30 810 94010801210135014801750208024002720304035103) 10 810 920102011201330159018702120 90 880 990111012201440173020102300 65 9101030114012501480178020802380 50 820 9401050117012901520182021302440 40 760 89010201150127014001650199023202650 30 1100128014601650183020102380287033403820 10 860 9701080118014001630185020502240 90 93010501170128015201770200022202430 65 96010901210133015701820207023002510 50 870 99011101240136016101870212023602580 40 810 940108012101350148017502040231025602800 30 11601360155017401940213025202930332036904030 10 9701090121013401580182020402240 90 10501190132014501710197022102430 65 10901220136015001770204022802510 50 98011201260140015401820209023502580 40 910106012101370152016701970227025502800 30 1310153017501970219024002840327036704030 10 112012601400154018102150249028203150 90 121013601510167019702340270030603420 65 125014101560172020302410279031603530 50 1120128014401610177020902480286032403620 40 10501220140015701740192022702690311035303940 30 15101760201022602510276032703880448050805670 10 12701430158017402060241027503075339036904500 90 13701550172018902235261529853340367540004885 65 14201600177019502305270030803445379541305040 50 128014601640182020052365277031653540390042405175 40 1190139015801780198021752575301534403845423546105625 30 1710200022802570285031353705434049505540610066408100 10 285/80 R 16 MPT 126 G 10 9 308866370 2540 298 425/55 R 17 MPT 13 428884399 2642 134 G 10321 325/70 R 18 MPT 11 331918421 2765 125 G 9 311 11365 365/70 R 18 MPT 12 375978449 2947 132 G 10 355 275/80 R 20 MPT 9 131 G 274966446 2890 335/80 R 20 MPT113201048 4853168 134 G 10 310 11390 375/70 R 20 MPT 12 4001034 4713107 136 G 10 380 405/70 R 20 MPT11405 1065 4853225 136 G 13 425 425/75 R 20 MPT13441 1148 5213440 148 G 11 421 445/65 R 22.5 MPT1) 160 G 14450 1172 5363525 13440 * More permitted rims on request 1) Tread pattern AC 70 + 44 2) agricultural tyres at 4,25 bar 3) tractor AC 70 G 8261 265/70 R 16 MPT 9 271775354 2333 114 G 7 251 AC 70 G at 4,75 bar 45 70 Series wide tyre – AC 70 G Technical data Load capacities Tyre size PermittedWidth Outer Static Rolling Speed Service rims* diameterloaded circum- radius description radius ference index LI/SS (mm)(mm)(mm)(mm) 380/70 R 24 W 12385 W 1339511905403524575 125 A8 (122 B) W 11 375 Tyre load capacity (kg) at tyre pressure (bar) Speed 0,60,81,01,21,41,62,02,53,03,54,04,56,0 (km/h) 1205 1310 1400 1500 50 12051325144015401650 40 115012901420154016501770 30 1400 1570 1725 1870 2005 2145 2475 10 1050118013201450171020302340265029503250 90 1140129014301570186022002540287032003530 65 1180133014701620192022702620296033003640 50 10601210136015101670197023302690304033903740 40 99011501320148016501810214025302920331036904060 30 142016601900213023702610308036504210476053105850 10 1410 1525 1640 1750 50 14051550168018001900 40 134015051660180019302035 30 1630 1830 2015 2185 2310 2470 2850 10 12201370152016701980244029303450 90 13201490165018202150265031803740 65 13701540171018802220274032903860 50 123014001580175019302280281033703970 40 1140133015201710190020902480305036704310 30 1650192021902470274030203560440052806210 10 1735 1880 2015 2180 50 17301905206522152360 40 165018552040221523752525 30 2005 2250 2480 2690 2885 3070 3540 10 14401620180019802340284032503875 90 15601760195021502540308036304210 65 16201810202022202620318037504340 50 145016601860207022802690326038504460 40 1350157018002020225024702920355041904850 30 1940227025902920324035604210511060306980 10 1510 1640 1760 1900 50 15101660180519302060 40 144016151780193020702205 30 1750 1965 2160 2345 2515 2680 3090 10 1550 1700 1890 2240 2630 3050 32501) 50 150017001885208024602920339035501) 40 160018202020223026303120363038001) 30 225025502820312036904360506053251) 10 1915 2075 2230 2360 50 19152105228524502575 40 182520502255244526202755 30 2215 2490 2740 2970 3185 3350 3865 10 2035 2205 2365 2500 50 20302235242526002725 40 193521702390259527802915 30 2350 2640 2905 3150 3380 3545 4090 10 2295 2490 2670 2900 50 22902525274029353150 40 218524552700293031403370 30 2655 2985 3285 3560 3820 4095 4725 10 2420 2625 2815 3075 50 24202660288530953350 40 230525902850309033153585 30 2800 3145 3460 3755 4025 4355 5025 10 W 13435 445/70 R 24 W 14 L 445 1248 561 3708 151 G W 12 425 R 24 480/70 138 A8 (135 B) W 15 L483 W 16 L 493 1313 W 14 L 473 582 3908 625 W 15 L493 495/70 R 24 MPT W 16 L 503 1313 582 3908 155 G W 14 L 483 420/70 R 28 133 A8 (130 B) W 13425 W 14 L 435 1348 W 12 415 604 4027 440/70 R 28 IND 152 A8 (149 B) W 13 435 W 14 L 445 1348 W 15 455 604 4027 650 W 15 L485 480/70 R 30 W 16 L 495 1462 653 4345 700 141 A8 (138 B) W 14 L 475 480/70 R 34 W 15 L486 W 16 L 496 1580 716 4711 750 143 A8 (140 B) W 14 L 476 W 16 L539 520/70 R 34 W 18 L 559 1649 740 4930 775 148 A8 (145 B) W 15 L 529 520/70 R 38 150 A8 (147 B) W 16 L530 W 18 L 550 1747 W 15 L 520 782 5230 825 1) Load values given for 0,4 bar and for 0,6 bar at 40 km/h are for calculating dual and triple load values only. or intensive road transport at 65/50/40/30 km/h the pressure must be increased by 0,4 bar. F Maximum inflation pressure should never be exceeded. ll load-speed-pressure data is valid for ground slopes up to and including 20%. A When operating on slopes greater than 20%, please, contact Mitas. 30 km/h (up to 40 km/h) load values also apply for low-speed high-torque field work. For plowing with single driven tires in the furrow, a minimum inflation pressure of 0,8 bar is required. 46 at 3,2 bar * More permitted rims on request All load values are for maximum indicated speeds at low torque. tractor AC 70 G 405/70 R 24 MPT 13 41911665413530 149 G W 13435 420/70 R 24 W 14 L 44512485613708600 130 A8 (127 B) W 12 425 AC 70 G agricultural tyres 47 85 Series standard tyre – AC 85 Suitability of the AC 85 in the field and on the road [Standard tyre with 85% aspect ratio, approved for speeds up to 50 km/h - 31 mph] Field performance 7 3 Road performance Economy* In the field, on grassland and on the road – the AC 85 delivers high performance, meeting the demands made by a wide range of applications. *Based on: rolling resistance, mileage, traction and gentle ground handling Traction 66 90 88 110 132 162 191 >220 120 150 180 220 260 >300 AC 85 Modern 85 Series all-round standard tyre for all applications qRadial tyre with balanced characteristics for a wide range of applications Grassland suitability both in the field and on the road AC 85 Driving stability Standard Transportation capability Load capacity 48 48 44 60 Driving comfort Gentle ground handling AC 85 22 30 Mileage q Larger ground contact patch makes the tyre well suited for handling grassland q Long service life thanks to the use of a wear resistant tread compound Cross-ply tyre tractor AC 85 kW hp Radial tyre Radial tyres offer better traction and enhanced ground protection than cross-ply tyres, because of their larger, rectangular ground contact patch. 49 85 Series standard tyre – AC 85 Technical data Load capacities Tyre size PermittedWidth Outer Static Rolling Speed Service rims* diameterloaded circum- radius description radius ference index LI/SS (mm)(mm)(mm)(mm) 280/85 R 20 W 10299 112 A8 (109 B) 981444 2934475 W 9289 11.2 R 20 280/85 R 24 W 10296 115 A8 (112 B) 1090 4973267 525 W 9286 11.2 R 24 320/85 R 24 W 11343 122 A8 (119 B) W 10 333 1158 530 3484 550 12.4 R 24 W 9 323 340/85 R 24 W 123721189 5363552 575 125 A8 (122 B) W 11362 13.6 R 24 380/85 R 24 W 12402 131 A8 (128 B) W 13 412 1258 563 3745 600 14.9 R 24 W 11 392 420/85 R 24 W 15475 137 A8 (134 B) W 14 465 1320 591 3930 625 16.9 R 24 W 13 455 280/85 R 28 W 10298 118 A8 (115 B) 1190 5513582 575 W 9288 11.2 R 28 320/85 R 28 W 11329 124 A8 (121 B) W 10 319 1259 578 3793 600 12.4 R 28 W 9 309 340/85 R 28 W 12367 127 A8 (124 B) 1299 5873885 625 W 11357 13.6 R 28 Tyre load capacity (kg) at tyre pressure (bar) Speed (km/h) 0,60,81,01,21,41,62,02,4 3,0 820 890 955 1030 50 820900980 1050 1120 40 780 880 970105011251200 30 950107011751275136514551680 10 890 970 1040 1120 50 890 980107011401215 40 850 9601050114012201300 30 1030116012801390149015801825 10 1100 1190 1275 1360 50 10951205130514001500 40 104511751290140015001605 30 1270142515701700182519502250 10 1205 1305 1400 1500 50 12051325143515401650 40 114512901420153516501765 30 1395156517201870200521452475 10 1430 1555 1665 1800 50 14301575171018301950 40 136515301685183019602090 30 1660186020502220238025352925 10 1680 1820 1950 2120 50 16751845200021452300 40 159517951970214022952460 30 1940217523952600279029903450 10 965 1045 1125 1215 50 9651060115012351320 40 92010301135123013201410 30 1120125513801495160517151980 10 1180 1280 1370 1450 50 11801295140515101600 40 112512601385150516151710 30 1365153016851830196020802400 10 1295 1400 1505 1600 50 12951425154016551750 40 123013801520165017701875 30 1500168018502005215022752625 10 1535 1665 1785 1900 50 15351690183019652060 40 146016401800196021002205 30 1775199521952380255026803090 10 1790 1945 2085 2240 50 17901970213522902430 40 170519152110229024502600 30 2070232525602780298031603645 10 1585 1720 1845 2000 50 15851740189020252180 40 151016951865202021702335 30 1835206022652460263528353270 10 1850 2005 2150 2300 50 18452030220523652500 40 176019752175236025302675 30 2140240026402865307532503750 10 2130 2310 2480 2650 50 21302340254027202900 40 203022802510272029103100 30 2460276030403300354037704350 10 380/85 R 28 133 A8 (130 B) 14.9 R 28 420/85 R 28 139 A8 (136 B) 16.9 R 28 380/85 R 30 135 A8 (132 B) 14.9 R 30 420/85 R 30 140 A8 (137 B) 16.9 R 30 460/85 R 30 145 A8 (142 B) 18.4 R 30 W 12401 W 13 411 1362 W 11 391 W 15459 W 14 449 1431 W 13 439 W 12398 W 13 408 1427 W 11 388 W 15472 W 14 462 1478 W 13 452 W 16516 W 15 506 1546 W 14 496 608 4050 650 641 4262 675 641 4255 675 666 4414 700 697 4618 725 tractor AC 85 AC 85 * More permitted rims on request 50 agricultural tyres 51 85 Series standard tyre – AC 85 Technical data Load capacities Tyre size PermittedWidth Outer Static Rolling Speed Service rims* diameterloaded circum- radius description radius ference index LI/SS (mm)(mm)(mm)(mm) 380/85 R 34 W 12401 146 A8 (146 B) W 13 411 1538 699 4577 725 14.9 R 34 W 11 391 420/85 R 34 W 15471 142 A8 (139 B) W 14 461 1598 724 4761 750 16.9 R 34 W 13 451 420/85 R 34 W 15469 147 A8 (147 B) W 14 459 1593 722 4755 750 16.9 R 34 W 13 449 460/85 R 34 W 16518 147 A8 (144 B) W 15 508 1676 756 4982 775 18.4 R 34 W 14 498 13.6 R 36 1) W 123601499 6924492 725 127 A8 (124 B) W 11 350 340/85 R 38 W 123651562 7194685 750 133 A8 (130 B) W 11355 13.6 R 38 Tyre load capacity (kg) at tyre pressure (bar) Speed 0,60,81,01,21,41,62,02,4 3,0 (km/h) 185020052150229025353000 50 1680185020052150229025353000 40 16001800198021452300245027103210 30 194521852405261027952970329539004500 10 1960 2125 2280 2430 50 19552155233525052650 40 186520952305250026802835 30 2265254528003035325534453975 10 215523352505265029053075 50 1955215523352505265029053075 40 18652095230525002680283531103290 30 226525452800303532553445377540004350 10 2250244526202800 50 22502475268528803075 40 214524052650287530803290 30 2605292532203490374540004615 10 1160 1300 1450 1600 50 11101270143015901750 40 102011901360153017001870 30 1240145016601860207022802630 10 1505 1635 1750 1900 50 15001655179519252060 40 143016051770192020602205 30 1740195521502335250026803090 10 172018802090230025052650 50 1545172018802090230025052650 40 14551655184020102235246026802835 30 177020102235244027152990325534453900 10 2070 2240 2400 2575 50 20652270246526402800 40 196522102430263528303000 30 2390268529553205343536404200 10 2370 2575 2760 3000 50 23702605283030303250 40 225525352790303032453480 30 2745308033903680394542254875 10 2865 3105 3330 3550 50 28603150341536603875 40 272530603370365539204145 30 3310372040904440476050405815 10 2565280531253450 50 23052565280531253450 40 217024652745300033453690 30 2840323035903925437548305175 10 300032553490371041104375 50 2995330035753840407545204750 40 28603205353038254100436048355085 30 347038954285465049905300587561757125 10 190020752310254027853000 50 1875208522802535279030603250 40 17652010223524402715298532752480 30 231526252920319525503905428545504875 10 268529353245355039604250 50 2410268529353245355039604250 40 22702580287031403470380042404550 30 276031353485381542154615554559506300 10 3135 3400 3645 3875 50 31303445373540054250 40 278533503685400042904550 30 3625407044804855521055256375 10 2180 23852640290032153450 50 1960 218023852640290032153450 40 18452095 233025502825310534403690 30 24152745 3050333537004060450548305175 10 2800 30603405375041054375 50 2515 280030603405375041054375 40 23702695 299532753645383043954680 30 31003525 3920428547655010575061256565 10 380/80 R 38 W 12380 142 A8 (142 B) W 11 370 1590 730 4790 14.9 R 38 W 13 390 420/85 R 38 W 15469 144 A8 (141 B) W 14 459 1696 772 5088 16.9 R 38 W 13 449 460/85 R 38 W 16508 149 A8 (146 B) W 15 498 1768 805 5280 18.4 R 38 W 14 488 520/85 R 38 W 165451857 8275515 155 A8 (152 B) W 18565 20.8 R 38 480/80 R 42 W 16513 151 A8 (151 B) W 15 503 1850 835 5540 18.4 R 42 W 14 495 520/85 R 42 W 16537 162 A8 (159 B) 1966 8965878 W 18557 20.8 R 42 380/90 R 46 W 12392 149 A8 (146 B) W 13 402 1844 846 5542 14.9 R 46 W 11 382 480/80 R 46 W 16507 158 A8 (158 B) W 15 497 1960 896 5886 18.4 R 46 W 14 487 520/85 R 46 W 16542 158 A8 (155 B) 2058 9256131 W 18562 20.8 R 46 380/90 R 50 W 12 380 151 A8 (151 B) W 13 3901949 8885850 14.9 R 50 W 11370 480/80 R 50 W 16 495 159 A8 (159 B)W 15 4852065 9456210 W 14475 * More permitted rims on request 52 1) 750 800 825 875 875 925 875 925 975 925 975 tractor AC 85 AC 85 Tread pattern AC 90 agricultural tyres 53 85 Series standard tyre – AC 85 – high load Technical data Load capacities Tyre size TreadPermittedWidth Outer Static Rolling Speed Service pattern rims* diameterloaded circum- radius description radius ference index LI/SS (mm)(mm)(mm) (mm) Tyre load capacity (kg) at tyre pressure (bar) Speed 1,21,62,02,42,83,23,64,04,4(km/h) 190020302180 2385257027402900 50 1795206022302360 2620282530103150 40 1920220523852525 2800302532253370 30 2205253527452905 3220347537053875 20 2515288531203305 36653955421544104650 10 2695309033453540 3930424045204725498010 cycl 254027853000 3255352537654000 50 2280279030603250 3580287041354375 40 2440298532752480 3830414544254680 30 2805343037654000 4405476050905380 20 3195390542854550 50105420579061256420 10 3425418545904875 5370581062056565688010 cycl 290032153450 3730402542904500 50 2385290032153450 3730402542904500 40 2550310534403690 3990430545904815 30 2930356539554245 4590495052755535 20 3335406045054830 52205635600563006620 10 3575435048255175 5595604064356750709510 cycl W 11355 1562719 4685 750 W 12365 380/90 R 46 W 12392 159 A8 (156 B) AC 85W 13 402 1844 846 5542 875 (replaces 14.9 R 46)W 11 382 380/90 R 50 W 12380 160 A8 (160 B) AC 85W 13 390 1949 888 5850 925 W 11 370 tractor AC 85 – high load 340/85 R 38 148 A8 (145 B) AC 85 (replaces 13.6 R 38) AC 85 * More permitted rims on request Load values given for 0,4 bar and for 0,6 bar at 40 km/h are for calculating dual and triple load values only. All load values are for maximum indicated speeds at low torque. 30 km/h (up to 40 km/h) load values also apply for low-speed high-torque field work. For plowing with single driven tires in the furrow, a minimum inflation pressure of 0,8 bar is required. or intensive road transport at 50/40/30 km/h the pressure must be increased by 0,4 bar. F Maximum inflation pressure should never be exceeded. ll load-speed-pressure data is valid for ground slopes up to and including 20%. A When operating on slopes greater than 20%, please, contact MITAS. 54 agricultural tyres 55 Harvester tyre SVT CHO [SVT CHO approved for speeds up to 50 km/h (31 mph)] Mobility increase Extension of time frame for harvesting by reducing inflation pressure Its outstanding qualities of gentle ground handling extend the time frame for harvesting, as SVT CHO performs excellently even on moist or wet soil conditions – for the maximum yield of your harvest! The most gentle ground handling tyre extending comfortably the harvesting time frame SVT CHO SVT not acceptable acceptable dry moist wet q q Harvester tyre with maximum cyclic axle load capacity q Larger footprint than standard harvester tyres guarantees gentler ground handling and extends the harvesting time frame q Due to its compact, narrow construction the tyre fulfills all legal requirements (limited vehicle width). Soil condition Harvesting time frame harvester SVT CHO NEW ! SVT CHO Suitability of the SVT CHO during harvest time Extremely low inflation pressure and more maximum load capacity at the same time, e.g. 1.6 bar vs. standard tyre 3.0 bar at a load of 10,710 kg SVT CHO 56 57 Harvester tyre SVT CHO Technical data Load capacities Tyre size TreadPermittedWidth Outer Static Rolling Speed Service pattern rims* diameterloaded circum- radius description radius ference index LI/SS (mm)(mm)(mm)(mm) Tyre load capacity (kg) at tyre pressure (bar) Speed 0,60,81,01,21,41,62,02,42,83,24,0(km/h) 50 6900 6435 6000 5515 5000 4635 4230 3865 40 7500 7070 6500 6060 5450 5090 4645 4245 3915 30 8025 7565 6955 6485 5830 5445 4970 4540 4190 3775 25 8235 7850 7215 6725 6050 5650 5155 4710 4345 3915 20 9225 8695 7995 7450 6705 6260 5715 5220 4815 4340 10 CHO ## 9810 10905 11700 12725 13500 9165 8365 7640 7045 6350 50 6300 5965 5450 5010 4575 4180 40 6900 6555 6000 5505 5025 4590 4235 30 7385 7015 6420 5895 5380 4915 4530 4085 25 7660 7275 6600 6115 5580 5095 4700 4235 20 8485 8060 7380 6775 6180 5650 5210 4695 10 CHO ## 9915 10800 11800 12500 9045 8265 7625 50 6500 5950 5300 5020 4650 4250 40 7100 6535 5800 5515 5110 4670 4315 30 7595 6995 6205 5900 5465 5000 4615 4165 25 7880 7255 6440 6120 5670 5185 4790 4320 20 8735 8040 7135 6785 6285 5745 5305 4790 10 CHO ## 9925 10440 11765 12780 9195 8410 7765 50 7750 7215 6700 6060 5530 5055 40 8500 7925 7300 6660 6080 5555 5120 30 9095 8480 7810 7125 6505 5945 5480 4940 25 9435 8800 8105 7395 6750 6165 5685 5125 20 9750 10455 8980 8195 7475 6830 6300 5675 10 CHO ## 9995 10940 11990 13140 14270 15300 9220 65 7500 7035 6500 6115 5690 5190 40 8250 7705 7100 6695 6230 5685 5100 30 8625 8090 7475 7030 6545 5970 5360 4705 25 8990 8335 7705 7245 6745 6150 5520 4850 20 9225 8655 7995 7520 7000 6385 5730 5035 10 CHO ## 9345 10245 11005 11700 12665 13500 8385 65 7500 6985 6300 5825 5325 4875 40 8250 7650 6900 6380 5835 5340 4805 30 8625 8035 7245 6700 6125 5605 5050 4450 25 8990 8280 7465 6905 6315 5780 5200 4585 20 9225 8590 7750 7165 6555 5995 5400 4775 10 CHO ## 9590 10485 11340 12575 13500 8775 7900 65 8000 7490 6900 6415 5800 5390 4920 4495 4540 40 8750 8200 7555 7025 6350 5900 5385 4720 4765 4295 30 9200 8615 7935 7375 6670 6200 5660 4920 4425 25 9480 8875 8175 7600 6875 6385 5830 5170 4910 4595 20 9840 9210 8485 7895 7135 6630 6055 5325 5100 10 CHO ## 9705 10440 11550 12420 13480 14400 8860 8095 7465 AC 70 G DW 20 B DW 21 B DW 23 B 663 673 693 1960 858 5865 925 800/70 R 32 CHO 175 A8 (172 B) SVT DW 25 B DW 27 B 748 768 1932 845 5630 925 900/60 R 32 CHO 176 A8 (173 B) SVT DW 27 B DW 30 B 835 865 1927 851 5700 925 900/70 R 32 CHO 182 A8 (179 B) SVT DW 25 B DW 30 B 881 911 2061 904 6075 975 800/70 R 38 CHO 178 D (181 A8) SVT DW 25 B DW 27 B 766 786 2042 916 6090 975 900/60 R 38 CHO 178 D (181 A8) SVT DW 27 B DW 30 B 860 890 2060 918 6115 975 680/80 R 42 CHO ° SVT 180 D (183 A8) DW 21 B DW 23 B DW 20 B 660 680 650 2160 965 6400 1025 ° calculated ## * More permitted rims on request 30 km/h (up to 40 km/h) load values also apply for low-speed high-torque field work. Load-pressure data for cyclic (CHO) applications apply to low-torque transport operations at max. speeds of 10 km/h and for a max. distance of 800 meters before discharging the load and returning empty. For plowing with single driven tires in the furrow, a minimum inflation pressure of 0,8 bar is required. Note : Cyclic applications means the case of harvester moving with full grain tank till its discharging. For intensive road transport at 50/40/30 km/h the pressure must be increased by 0,4 bar. Maximum inflation pressure should never be exceeded. Load values given for 0,4 bar and for 0,6 bar at 40 km/h are for calculating dual and triple load values only. All load-speed-pressure data is valid for ground slopes up to and including 20%. When operating on slopes greater than 20%, please, contact Mitas. All load values are for maximum indicated speeds at low torque. 58 tractor harvesterSVT SVTCHO CHO 680/85 R 32 CHO 178 A8 (175 B) SVT CHO agricultural tyres 59 AC 70 H/G/N SuperVolumeTyre (SVT) Economical tyre for gentle ground handling on harvesters Harvester tyres compared with standard tyres [AC 70 H/G/N, SVT approved for speeds up to 50 km/h (31 mph)] The extremely wide tyres distribute the weight of the machine across the surface area; as a result, the plant roots remain virtually undamaged. 1,61,6 1,41,4 1,21,2 1,01,0 0,80,8 0,60,6 (Figures in bar) Standard tyres SVT 60 (harvester) 0,80,8 0,60,6 0,40,4 (Figures in bar) Harvester tyres: AC 70 H/G/N, SVT 0,70,7 0,50,5 0,30,3 harvester Harvester tyres – AC 70 H/G/N and SVT qHarvester tyre with high load capacities and low inflation pressure q Minimised load placed on soil structure, thanks to the wide and even distribution of ground pressure q q Low vibration on the road, through good absorption Very economical as a result of high mileage performance in field and road operations AC 70 H 61 Harvester tyres – AC 70 H/G/N and SVT Technical data Load capacities Tyre size TreadPermittedWidth Outer Static Rolling Speed Service pattern rims* diameterloaded circum- radius description radius ference index LI/SS (mm)(mm)(mm) (mm) Tyre load capacity (kg) at tyre pressure (bar) Speed 0,60,81,01,21,41,62,02,42,83,24,0(km/h) 320035003835416045655000 50 3245351538504215450050205450 40 31253470376041204510489553705835 30 32453600390042704680507555706050 25 35953990432547355185562561706705 20 38004215457050055480594565257085761080001)10 46755190562561556745731580308725937098451) 10 cycl ## 320035003835416045655000 50 3245351538504215450050205450 40 31253470376041204510489553705835 30 32453600390042704680507555706050 25 35953990432547355185562561706705 20 38004215457050055480594565257085761080001)10 46755190562561556745731580308725937098451) 10 cycl ## 32003500383541604565500053305800 50 324535153850421545005020545058556300 40 3125347037604120451048955370583562656740 30 3245360039004270468050755570605065006995 25 3595399043254735518556256170670572007750 20 38004215457050055480594565257085761081909235 10 10080 11365 10 cycl ## 467551905625615567457315803087259370 386542304635502555156000 50 3915424546455090552060606500 40 37754190454049755445591064856955 30 39154345471051555650613067257215 25 43404815522057156260679074507995 20 45855090552060406620717578758450919096551)10 5645626567907435814588359695 10400 11310 118851) 10 cycl ## 3900 4270 4610 5000 50 39504285469050655450 40 381042304585502054205830 30 395543854755520556256050 25 438048605270577062306705 20 46305140557061006585708576308185 10 10075 10 cycl ## 5700632568557505810587209390 390042704610500053105800 50 3950428546905065545058356300 40 38104230458550205420583062456745 30 39554385475552055625605064756995 25 43804860527057706230670571757750 20 46305140557061006585708575858190896094001)10 5700632568557505810587209335 10085 11025 115701) 10 cycl ## 39004270461050005310580062706900 50 395042854690506554505835630068907500 40 3810423045855020542058306245674573758025 30 3955438547555205562560506475699576508325 25 4380486052705770623067057175775084759225 20 4630514055706100658570857585819089609750 10820 10 10085 11025 12000 13320 10 cycl ## 5700632568557505810587209335 1) at 3,1 bar AC 70 H DW 20 B650 17957905255825 DW 21 B 660 650/75 R 32 167 A8 (164 B) AC 75 G DW 20 B635 17987825245825 DW 21 B 645 650/75 R 32 172 A8 (169 B) AC 70 G DW 20 B650 17957905255825 DW 21 B 660 680/85 R 32 173 A8 (170 B) AC 70 G DW 20 B 662 DW 21 B 672 1950 852 5865 925 DW 23 B 692 800/65 R 32 167 A8 (164 B) AC 70 H DW 25 B795 18208305430875 DW 27 B 815 800/65 R 32 172 A8 (169 B) AC 70 H DW 25 B795 18208305430875 DW 27 B 815 800/65 R 32 178 A8 (175 B) AC 70 N DW 25 B743 18358375500875 DW 27 B 763 * More permitted rims on request 62 agricultural tyres AC 70 G AC 70 N harvester 650/75 R 32 167 A8 (164 B) AC 70 H 63 Harvester tyres – AC 70 H/G/N and SVT Technical data Load capacities Tyre size TreadPermittedWidth Outer Static Rolling Speed Service pattern rims* diameterloaded circum- radius description radius ference index LI/SS (mm)(mm)(mm) (mm) Tyre load capacity (kg) at tyre pressure (bar) Speed 0,60,81,01,21,41,62,02,42,83,24,0(km/h) 418045755010546059656300 50 4235459050255505600065556900 40 40854530491553805895642070157385 30 42354700509555806115660072757660 25 46955210565061806775738080608485 20 49605505597065357160780085208970 10350 10 10485 11040 11730 10 cycl ## 610567757345804088109600 425046505020546059506500 50 4315467051105515600065357100 40 41654615500054655900642069957595 30 43204790518556706120666072557880 25 47905305574562856785738080408735 20 50605610607066407170780084959230 10650 10 623069057475817588259600 10460 11360 12070 10 cycl ## 46605055553060606700721577508415 9250 50 46155120555560806660730079258500925010000 40 49405480594565057125781084809095989510700 30 51255685616567507395810588009435 1026511100 25 5675630068307475819589809750 10455 1137512300 20 600066607220790586609490 10305 11050 1202513000 14585 10 7385 8195 8885 97251065511680126851360014800 1600017950 10 cycl ## 504555155955650070557500 50 4655504555155955650070557500 40 44954985539559006370695575508025 30 46655170559561206610721578308325 25 51705730620067857320799586809225 20 54656055655571707740845091759750 11250 10 67257450807088259525 10400 11290 12000 12750 10 cycl ## DW 25 B762 19328455630875 DW 27 B 784 SVT 900/60 R 32 176 A8 (173 B) DW 27 B857 19058505700925 DW 30 B 890 900/70 R 32 188 A8 (185 B) SVT DW 27 B895 20508966050975 DW 30 B 925 1050/50 R 32 178 A8 (178 B) SVT 36.00 VA 1015 18908455640875 * More permitted rims on request ## harvester 800/70 R 32 SVT 175 A8 (172 B) SVT harv. Load-pressure data for cyclic applications apply to low-torque transport operations at max. speeds of 10 km/h and for a max. distance of 800 meters before discharging the load and returning empty. Note : Cyclic application means the case of harvester moving with full grain tank till its discharging. Load values given for 0,4 bar and for 0,6 bar at 40 km/h are for calculating dual and triple load values only. All load values are for maximum indicated speeds at low torque. 30 km/h (up to 40 km/h) load values also apply for low-speed high-torque field work. For plowing with single driven tires in the furrow, a minimum inflation pressure of 0,8 bar is required. For intensive road transport at 50/40/30 km/h the pressure must be increased by 0,4 bar. Maximum inflation pressure should never be exceeded. All load-speed-pressure data is valid for ground slopes up to and including 20%. When operating on slopes greater than 20%, please, contact Mitas. 64 agricultural tyres 65 Harvester tyres – Steer wheels Specifically designed for use on the steering axle of h arvesting equipment. They offer extremely high volume of air and consequently high load bearing capacities, yet very compact format. The special tread pattern featuring smooth areas between the lugs, plus the steel belt design, make the tyres resistant to damage. The large ground contact area protects the soil. harvester SuperVolumeTyre (SVT) SuperVolumeTyre (SVT), AC 65 and AC 70 G Harvester steer wheels AC 65 AC 70 G 66 67 Harvester tyres – Steer wheels Load capacities AC 70 G Tyre size Tread Permitted Tube Width Outer pattern rims* and diameter Valve (TL-valve) (mm) (mm) Static Rolling loaded circum- radius ference (mm) 460/70 R 24 IMP AC 70 G W 15 L W 16 L TL – W 14 L 455 5523690 • 465 1236 5283620 445 W 16 L 496 5913919 TL– 4861313 5733908 W 15 L • 500/70 R 24 IMP AC 70 G W 16 L S 18.4(15)-26 T TL W 15 L 47 GW S • 500/85 R 24 IMP SVT • 528 6504325 5181458 6214237 • • W 16 L S 18.4(15)-26 T 517 6634440 500/80 R 28 IMP SVT TL 1495 W 15 L 47 GW S 507 6354355 W 18 L 590 • S 18.4(15)-26 T 6614411 600/65 R 28 IMP AC 65DW 18 L TL 590 1485 47 GW S5706404340 W 16 L W 16 L S 18.4(15)-26 T 500/85 R 30 IMP SVT TL W 15 L 47 GW S W 16 L 540/65 R 30 IMP AC 65 W 18 L TL – W 15 L • 527 7114750 1605 517 6804669 526 664 • 4420 546 1485 6484365 516 W 18 L 620/70 R 30 IMP SVTDW 20 B TL – DW 21 B 625 645 1595 655 500/85 R 34 IMP° SVT ° calculated 68 700 • 4870 6804770 • W 16 L 503 7555050 TL– 4931705 7455000 W 15 L • • • • • 151 A8 163 A8 135015401735 2120245527903110345040 190521752450 2995346539404395487540 155 A8 164 A8 1685 2170 1925 2480 2165 2790 2645 3410 3065 3950 3480 4490 3875 5000 1795 2600 2050 2970 2310 3340 2820 4085 3270 4730 3715 5375 4250 40 6150 40 1940 2755 2215 3150 2495 3540 3050 4330 3530 5015 4015 5700 4480 6360 2170 3040 2480 3475 2790 3910 3410 4775 4000 5600 2110 2995 2410 3425 2715 3855 3315 4710 3840 5455 4365 6200 1900 2660 2170 3040 2445 3420 2985 4180 3460 4840 4000 5600 2490 3525 2850 4030 3205 4535 3560 5035 3915 5540 4535 6415 5300 40 7500 40 2555 3620 2875 4070 3195 4525 3515 4975 4070 5760 4630 6550 5300 40 7500 40 158 A8 171 A8 164 A8 176 A8 156 A8 168 A8 164 A8 176 A8 156 A8 168 A8 • 166 178 166 178 * More permitted rims on request AC 65 LI/SS Tyre load capacity (kg) at tyre pressure (bar) PR Speed 0,81,01,2 1,62,02,42,83,23,6 5,0 (km/h) • • SVT A8 A8 A8 A8 • • • • • • • • 40 40 harvester Technical data harvester steer wheels 5000 40 7100 40 40 40 5000 40 7100 40 40 40 When fitted on tractor steering wheels, tyre load capacities are 80% of the loads for free-rolling applications. drive wheel free rolling axle agricultural tyres 69 Implement radial tyres (IMP) Implement radial tyres (IMP) Tread patterns and recommended applications Multi-Service Radial tyre designed for use on fastmoving self-loading forage boxes and trailers at speeds of up to 65 km/h (40 mph). The larger footprint, thanks to the wide tread, and low tyre pressure protect both grassland and soil. The evenly balanced tread pattern design means the tyre is also suitable for utility vehicles (e.g. cleaning pavements) and for long journeys. Radial traction tyre for use on grassland. Ideally suited for working on slopes; protects the turf. Very quiet running on roads at speeds of up to 65 km/h (40 mph). High mileage performance through optimised tread pattern design. Technical data IMP Load capacities Tyre size Tread Permitted Tube Width Outer pattern rims* and diameter Valve (TL-valve) (mm) (mm) 441 873393 2605 431 500/50 R 17 IMP 520 * More permitted rims on request 70 Static Rolling loaded circum- radius ference (mm) 440/50 R 17 IMP 14.00 x17 All-Ground 13.00 x17 TL – (replaces 425/55 R 17) Multi-Service 16.00 x17 TL IMP radial tyres All-Ground – 933 425 2800 LI/SS Tyre load capacity (kg) at tyre pressure (bar) PR Speed 0,81,01,2 1,62,02,42,83,23,6 5,0 (km/h) 870 950 1075 1185 1295 1190 1315 1435 1420 1570 1715 149 D 135 D 1100 1500 1665 1985 1150 1740 1930 2305 1430 1940 2155 2570 1505 2275 2530 3015 1575 2145 2380 2840 1680 2540 2825 3365 1715 2330 2585 3085 1845 2785 3090 3685 2040 2775 3080 3670 2200 3330 3695 4405 218065 2965 40 3290 30 3925 10 2665 325065 4030 4420 40 4470 4910 30 5330 5850 10 When fitted on tractor steering wheels, tyre load capacities are 80% of the loads for free-rolling applications. 71 Multi purpose radial tyres (MPT) Agro-Trailer Radial tyre for agricultural and utility trailers; approved for speeds of up to 100 km/h (62 mph). The longitudinal and lateral structure of the tread pattern, combined with rounded tread shoulders, ensures low rolling resistance. The all-steel construction protects the tyre from damage. 72 AC 70 G Special tractor drive wheel profile particularly good for avoiding damage to meadowland. Extremely quiet running on the road. Also well adapted for field use. Can be used on multi-purpose vehicles (90 km/h / 56 mph), telescope loaders and front axles of four-wheel d rive tractors. MPT radial tyres Multi purpose radial tyres (MPT) Tread patterns and recommended applications 73 Multi purpose radial tyres (MPT) Load capacities Tyre size Tread Permitted Tube Width Outer LI/SS pattern rims* and diameter Valve (TL-valve) (mm) (mm) Static Rolling loaded circum- radius ference (mm) 8(43 GS 16)** 261 265/70 R 16 MPTAC 70 G 9 TL 10.0/75-15.3 T 271 775 354 2333 114 G 7 47 GW S 251 (43 GS 16)** 10 308 285/80 R 16 MPTAC 70 G TL 10.0/75-15.3 T 865392 2579 9 298 126 G 47 GW S (43 GS 16)** 425/55 R 17 MPT 19.0/45-17 T 428 884 399 2642 AC 70 G 13.00 x 17 TL 134 G 505/50-17 T 431 873 393 2605 38 G 16 S 10 321 325/70 R 18 MPTAC 70 G 11 TL(43 GS 16)** 331 918 421 2765 125 G 9 311 (43 GS 16)** 10.5/80-18 355/60 R 18 MPTAgro-Trailer11 x 18 TL13.0/65-18 352 890 398 2650 142 J 355/60 -18 T 38 G16 11 365 365/70 R 18 MPTAC 70 G 12 TL(43 GS 16)** 375 978 449 2947 132 G 10 355 275/80 R 20 MPTAC 70 G 9 TL(43 GS 16)** 274 966 446 2890 131 G 335/80 R 20 MPT 11 320 AC 70 G TL(43 GS 16)** 1048 485 3168 134 G 10 310 (43 GS 16)** 1116/70-20 390 375/70 R 20 MPTAC 70 G 12 TL 375/70-20 T 400 1034 471 3107 136 G 10 405/70-20 T 380 47 GW S (43 GS 16)** 16/70-20 405/70 R 20 MPT 11 405 AC 70 G TL 375/70-20 T 1065 485 3225 136 G 13 425 405/70-20 T 47 GW S 425/75 R 20 MPT 13 AC 70 G TL(43 GS 16)** 4411148 521 3440 148 G 11 421 445/65 R 22.5 MPT 14 AC 70 + TL(43 GS 16)** 4501172 536 3525 160 G 13 440 * More permitted rims on request 74 ** Valve 50 GW optional agricultural AgroTrailer Tyre load capacity (kg) at tyre pressure (bar) single tyre fitment Speed 1,62,02,53,03,54,04,55,06,0(km/h) 630 740 880 1030 1180 90 680 800 960 1120 1280 65 790 93011101280145017001) 90 65 860101012001390157018401) 10801280155018302120 90 11701390168019902300 65 9001060126014601650 90 9801150137015801790 65 10301220146017001930217024102650 100 11201320158018402090235026102880 65 10801280152017602000 90 11701380165019102170 65 820 970116013401510169019502)90 8901060125014501640183021202)65 11201330159018702120 90 12201440173020102300 65 118014001630185020502240 90 128015201770200022202430 65 13401580182020402240 90 14501710197022102430 65 154018102150249028203150 90 167019702340270030603420 65 174020602410275030803390369039704500 90 189022352615298533403675400043104885 65 1) tyres AC 70 G MPT radial Technical data MPT at 4,25 bar 2) at 4,75 bar 75 Multi purpose radial tyres (MPT) Technical data MPT Load capacities Tyre size Tread Permitted Tube Width Outer LI/SS pattern rims* and diameter Valve (TL-valve) (mm) (mm) 13 419 405/70 R 24 MPTAC 70 G 12 TL(43 GS 16)** 409 1166 149 G 11 399 * More permitted rims on request 76 541 3530 Tyre load capacity (kg) at tyre pressure (bar) single tyre fitment Speed 1,62,02,53,03,54,04,55,06,0(km/h) 1450171020302340265029503250 90 1570186022002540287032003530 65 1248 1313 561 582 3708 3908 16701980244029303450 90 18202150265031803740 65 19802340284032503875 90 21502540308036304210 65 ** Valve 50 GW optional agricultural tyres MPT radial (43 GS 16)** W 1314.9-/16.9-24 435 445/70 R 24 MPT AC 70 G W 14 L TL 420/70-24 T 445 151 G W 12 480/70-24 T 425 47 GW S (43 GS 16)** W 15 L14.9-/16.9-24 493 495/70 R 24 MPT AC 70 G W 16 LTL 420/70-24 T 503 155 G W 14 L 480/70-24 T 483 47 GW S Static Rolling loaded circum- radius ference (mm) AC 70 G 77 Cross-ply tyre – AS-Farmer AS-Farmer Tough cross-ply tyre for tractors qProven cross-ply tyre for tractors q Versatile and suitable for different agricultural use, particularly on dry grounds q q 78 cross-ply AS-Farmer High lugs ensure good traction High resistance against puncture, cuttings and abrasion 79 Cross-ply tyre – AS-Farmer Technical data Load capacities Tyre size Permitted Tube Width Outer Static Rolling Radius Service rims* and diameterloaded circum- index description Valve radius ference Ply Rating (PR) (mm) (mm) (mm) (mm) (mm) 7.5 L - 15 6 LB 7.5-15/28x9.00-15 T 213 TT 762355 2275 345 38 G 11.5 S 97 A8 / 6 PR 5 1/ J 208 4.50 E 179 6.50 - 16 5.50 F TL 6.00-/6.50-/7.00-16 T189 773360 2280 350 99 A8 / 8 PR 5.00 F 38 G 16 S 184 4.00 E 174 5.00 F 204 7.50 - 16 7.00-/9.00-16 T 8 PR 6.00 F TL 214 808370 2430 375 5.50 F 38 G 16 S 209 8.3 - 24 8.3(8)-24 T W 6 201 995470 2872 470 TT 6 PR W7 211 47 GW S Tyre load capacity (kg) at tyre pressure (bar)# Speed## 1,01,41,61,71,82,12,42,83,13,43,7 (km/h) 37546550552054560566073040 41551556058060567073582030 48059064567069577084594520 50562568070573581589599510 38547051053054560065572077540 41550554556558564570077083030 47558062565067574080088095520 505610660690710780850935 101010 42050554556058063068074078583087530 505605650675695755815890940995 105020 545655705730755820880960 1020 1080 134010 440 550 625 30 530 660 730 20 570 720 790 10 570700765795830920 1005 111030 685840920955995 1100 1210 134520 745 915 99510351075119513101455 10 670 830 920 960 1000 1125 1250 30 800100011001150120013501500 20 870109011901250130014601625 10 885 1065 1155 1200 1245 1415 30 1060 1280 1385 1440 1490 1710 20 1240 1490 1615 1680 1740 1995 10 1200 1500 1650 1730 1800 30 1440 1800 1980 2070 2160 20 1560 1950 2150 2240 2340 10 960120013201380144016201800204022202400 30 1150144015801660173019402160245026652880 20 1250156017201790187021102340265028853120 10 49061067070072580086093599030 590730800840870950 1030 1120 119020 630790870910940 1030 1120 1215 129010 760 93010151055109512101320 30 915111512151265131014501585 20 990121013151370142015701715 10 890 1120 1230 1285 30 1070 1340 1480 1540 20 1160 1450 1600 1670 10 620 780 860 890 930 1035 30 750 930 1030 1070 1120 1240 20 810 1010 1110 1160 1210 1340 10 1600 2000 2200 2300 30 1920 2400 2640 2760 20 2080 2600 2860 2990 10 49061068071074083092030 590740810850880990 100020 640800880920960 1080 120010 640 800 875 915 950 1065 30 770 955 1050 1095 1140 1280 20 835 1035 1135 1185 1235 1385 10 950 1180 1300 1360 30 1140 1420 1560 1630 20 1230 1540 1690 1770 10 9.5 - 24 W 7 2311050 TT 9.5-/11.2(9/10)-24 T 495 3070 495 8 PR W8 241 47 GW S 11.2 - 24 W 9 2741105 520 3300 515 TT 9.5-/11.2(9/10)-24 T 8 PR W 10 284 47 GW S W 9 295 12.4 - 24 11 TT 12.4-/13.6(11/12)-24 T315 1160 539 3473 540 8 PRW 47 GW S305 W 10 W 11 358 14.9-/16.9(13/14)-24 T378 14.9 W - 24 1265 13 TT 8 PR 47 GW S368 W 12 W 11 358 14.9/80-24 T 14.9/80 - 24 13 TT 3781215 12 PRW 47 GW S368 W 12 8.3 - 28 W 6 8.3-/9.5(8/9)-28 T 2011095 TT 8 PR W 7 47 GW S 211 11.2-/12.4/13.6-28 T 11.2 - 28 W 9 2741205 TT 284 8 PR W 10 47 GW S 581 3795 590 565 3642 580 521 3221 520 567 3529 565 W 9 295 11.2-/12.4/13.6-28 T3151260 12.4 W - 28 598 3750 590 11 TT 6 PR 47 GW S305 W 10 9.5 - 30 W 7 231 TT 270/80-32/9.5-30 T 6 PR 2411200 572 3540 570 W8 47 GW S 16.9 - 30 14.9-/16.9(13/14)-30 T W 14 L TT 8 PR W 15 L 47 GW S 8.3(8)-32 T 8.3 - 32 W 6 TT 6 PR W7 47 GW S 9.5-/11.2(9/10)-32 T 9.5 - 32 W 7 TT 6 PR W8 47 GW S W 9 12.4(11)-32 T 12.4 - 32 11 TT 6 PRW W 10 47 GW S 80 4191485 685 4390 695 429 2011195 571 3543 570 211 2311250 597 3695 595 241 295 3151360 633 3975 640 305 * More permitted rims on request # For tread pattern that differ from AS-Farmer see page 17 ## agricultural tyres cross-ply 2 AS-Farmer For field applications under high and sustained torque, the loads for 30 km/h (19 mph) apply. For speeds up to 40 km/h (25 mph) see page 98 81 Cross-ply tyre – AS-Farmer Technical data Load capacities Tyre size Permitted Tube Width Outer Static Rolling Radius Service rims* and diameterloaded circum- index description Valve radius ference Ply Rating (PR) (mm) (mm) (mm) (mm) (mm) 16.9-/18.4(14/15)-34 T 16.9 - 34 W 14 419 TT 8 PR W 15 L 4291585 724 4680 745 47 GW S Tyre load capacity (kg) at tyre pressure (bar)# Speed## 1,01,41,61,71,82,12,42,83,13,43,7 (km/h) 1690 2110 2320 2430 30 2030 2540 2790 2920 20 2200 2750 3020 3160 10 2120 2650 30 2540 3180 20 2760 3450 10 550 690 755 30 660 820 910 20 710 890 980 10 670 840 920 960 1000 1130 30 800 1000 1110 1160 1210 1360 20 870 1090 1200 1250 1310 1470 10 670 840 920 960100011301220134014301520 30 800100011101160121013601460161017151830 20 870109012001250131014701590174018601980 10 640 800 880 910 95010701190137015051640 30 760 95010501100115012901430164518051960 20 830103011401190124013901550178019552120 10 8.3-/9.5-36 T 9.5 - 36 W 7 TT 6 PR W8 47 GW S 8.3-/9.5-36 T 9.5 - 36 W 7 TT 10 PR W8 47 GW S 9.5-/11.2-42 T 9.5 - 42 W 7 TT 10 PR W8 47 GW S 82 4571650 750 5003 770 467 2111300 622 3915 620 2311355 640 4000 645 241 2311355 640 4000 645 241 231 2411505 724 4595 720 * More permitted rims on request # For tread pattern that differ from AS-Farmer see page 17 ## agricultural tyres cross-ply 16.9-/18.4(14/15)-34 T 18.4 - 34 W 15 L TT 8 PR W 16 L 47 GW S 8.3-/9.5-36 T 8.3 - 36 W 7 TT 4 PR 47 GW S AS-Farmer For field applications under high and sustained torque, the loads for 30 km/h (19 mph) apply. For speeds up to 40 km/h (25 mph) see page 98 83 Steering tyre – T 9 steering Steering tyre T 9 Cross-ply steering tyre for tractors T9 Tough steering tyre with a cross-ply q construction Multi-rib tread pattern with short, strong q shoulder lugs q Secure track holding and good c limbing capabilities when steering out of the furrow Technical data Load capacities Tyre size Permitted Tube Width Outer Static rims* and diameter loaded Valve radius (mm) (mm) (mm) 4.00 –16 3.00 D x 16 TT4.00/4.50-16 TAS 112630 302 AS-Front (T 9) 38 G 11.5/16 4.50 –16 3.00 D x 16 TT4.00/4.50-16 TAS 122655 308 AS-Front (T 9) 38 G 11.5/16 5.00 –16 3.50 D x 16 5.00/5.50-16 TAS TT 140680 318 AS-Front (T 9) 4.00 E x 16 38 G 11.5/16 6.00 –16 4.00 E x 16 6.00/7.00-16 T TT 165735 342 AS-Front (T 9) 4.50 E x 16 38 G 11.5/16 4.50 E x 16 6.50 –16 6.00/7.00-16 T 5.00 E x 16 TT 355 AS-Front (T 9) 38 G 11.5/16175 760 5.50 E x 16 7.50 –16 7.00/8.00-16 T 5.50 F x 16 TT 376 AS-Front (T 9) 38 G 11.5/16205 805 PR Tyre load capacity (kg) at tyre pressure (bar) Speed: 30 km/h 1,0 1,52,0 2,3 2,52,8 3,13,3 3,43,7 Front end loader 10 km/h kg/bar 4 160 200235 250 265280 295305 320 430/3,4 4 190 240285 305 325345 365 490/3,1 4 215 270320 345 370390 490/2,8 6 275 355420 450 480505 535560 1120/4,1 6 315 400475 510 545580 615 1230/3,9 6 385 500605 660 705745 1490/3,5 8 385 500605 660 705745 790815 840870 1740/4,6 * More permitted rims on request 84 85 Implement cross-ply tyres (IMP) Traction Farmer Implement cross-ply tyres (IMP) Tread patterns and recommended applications M3 Lugged tread pattern for powered axle. T 55/2 with central ridge for sickle bar mowers. M 159 Cross-divided rolling tread, for free rolling and powered axles. For municipal vehicles and golf course tractors. 86 Lugged tread pattern for driven wheels. Ribbed tread patterns without any lateral tread elements. IMP cross-ply AS-Farmer / T 55/2 AW-Farmer Farmer AW Good track holding for trailed wheels due to rolling rib profile and strong side lugs. 87 Implement cross-ply tyres (IMP) Technical data Load capacities Tyre size Tread Permitted Tube Width Outer Static loaded Rolling pattern rims* and diameter radius circum valve Roll Traction Roll Traction ference (mm) (mm) (mm) (mm) (mm) (mm) 11x7-4 F 11x7-4 M3 6.00 x 4 TT 185 270 117 28 G 920 S LI/SS Tyre load capacity (kg) at tyre pressure (bar) PR T 55/2 Implement AW-Farmer 4.25 x 12 AS-Farmer TL 5 JA x 121) spec. 5.00 x 12 AW-Farmer TT 4.25 x 12 10.0/75-12 AW-Farmer 9.00 x 12 7.00 x 12 11.0/65-12 AS-Farmer 9.00 x 12 7.00 x 12 7.00-12 8.00-12 AS-Farmer 10.0/75-15.3 AW-Farmer 9.00 x 15.3* M159 11.5/80-15.3 AS-Farmer 9.00 x 15.3* AW-Farmer replaces 11.5-15 4.00-16 Implement 6.00-16 Implement 230/70-16 replaces 9.0/70-16 270/75-16 replaces 10.0/75-16 15.0/55-17 replaces 15-17 15.0/55-17 replaces 15-17 AS-Farmer 3.00 D x 16 TL AS-Farmer 4.00 E x 16 TT AS-Farmer AS-Farmer 7.00 W8 W7 9 x 16 W9 W8 88 TL Farmer AW 13.00 x 17 TL TractionFarmer 13.00 x 17 TL * More permitted rims on request Rim 5 JA x 12 only use with inner tube 1) TL 1,5 1,8 2,0 2,3 2,5 2,8 3,1 4 PR 190 250 290 320 340 370 400 420 3,4 ASFarmer 3,9 AWFarmer 4,2 M 159 4,4 TractionFarmer Speed (km/h) 30 114 415 425 192 197 - 2 PR 120 155 181 195 667 687 308 316 2020 2070 6 PR 400 500 560 595 645 222 214 710 - 321 - 2102 6 PR 520 660 750 805 870 30 264 244 674 - 305 - 2013 6 PR 595 760 870 920 975 30 281 261 - 692 - 310 2125 8 PR 635 790 900 950 1020 1070 1120 1170 1270 38 G 16 S 264 764 786 343 353 2305 8 PR 10 PR 710 710 885 885 1000 1000 1060 1060 1140 1140 1190 1190 1260 1260 1330 1330 1460 38 G 16 S 290 845 - 372 - 2550 8 PR 10 PR 12 PR 930 930 930 1175 1175 1175 1320 1320 1320 1420 1420 1420 1520 1520 1520 1590 1590 1590 1675 1675 1675 1750 1750 1930 1930 7.00-12 T 38 G 16 S 8.00-12 T 38 G 16 S 10.0/75-12 T TT 11.0/65-12 T 38 G 16 S 10.0/75-12 T TT 11.0/65-12 T 38 G 16 S replaces 10-15 1,0 T 55/2 4.00-16 T 4.50-16 T 38 G 16 S 6.00-16 T 6.50-16 T 7.00-16 T 38 G 16 9.0/70-16 T 10.0/75-16 T 38 G 16 S 9.0/70-16 T 10.0/75-16 T 38 G 16 S 15.0/55-17 T (15-17 T) 38 G 16 S 15.0/55-17 T (15-17 T) 38 G 16 S 30 680 30 30 1550 30 30 2145 30 30 30 2145 114 - 628 - 296 1900 2 PR 210 260 164 - 735 - 345 2215 6 PR 385 470 535 570 620 650 685 600 690 730 765 790 810 830 860 915 935 950 40 - 770 - 335 325 460 240 650 500 860 650 980 710 1040 770 1080 825 1110 1150 1190 1250 1290 1330 1360 40 40 - 363 344 710 935 1010 1100 1180 262 - 811 • • 2285 2252 2440 2378 • • 106 A8 10 PR 119 A8 101 A8 6 PR 114 A8 • • 30 850 - 371 - 2570 10 PR 1090 1460 1640 1750 1970 2120 367 - 858 - 373 2592 12 PR 1090 1460 1640 1750 1970 2120 drive wheel free rolling axle 30 40 367 • IMP cross-ply 4.00-8 3.50-8/400x100 3.00 x D-8 TT 4.40-8/400x100 38 G 11.5 S M3 30 2240 2360 30 When fitted on tractor steering wheels, tyre load capacities are 80% of the loads for free-rolling applications. agricultural tyres 89 Implement cross-ply tyres (IMP) Technical data Load capacities Tyre size Tread Permitted Tube Width Outer Static loaded Rolling pattern rims* and diameter radius circum valve Roll Traction Roll Traction ference (mm) (mm) (mm) (mm) (mm) (mm) 12.5/80-18 T 443 • 3025 • 320/80-18 AS-Farmer 9 x 181) TL 14.5/80-18 T 308 1000 replaces 12.5/80-18 430 3015 38 G 16 S 16/70;335/80-20 11 x 20 360 492 • 3205 • 360/80-20 AS-Farmer TL 375/405/70-20 1092 replaces 14.5/75-20 12 x 20 370 485 3200 47 GW S 16/70;335/80-20 13 x 20 412 503 • 3337 • 400/70-20 AS-Farmer TL 375/405/70-20 1106 replaces 16/70-20 14 x 20 422 493 3325 47 GW S W 13 14.9-/16.9-24 T 376 • 586 3841 • 15.5/80-24 AS-Farmer W 14 TL (13/14-24 T) 387 1270 575 3820 W 12 365 47 GW S W 13 14.9-/16.9-24 T 376 3841 • 586 • 15.5/80-24 AS-Farmer W 14 TL (13/14-24 T) 387 1270 575 3820 W 12 365 47 GW S W 13 14.9-/16.9-24 T 413 590 • 4032 • 16.5/85-24 AS-Farmer W 15 L TL (13/14-24 T) 435 1338 580 4010 W 14 L 424 47 GW S LI/SS Tyre load capacity (kg) at tyre pressure (bar) PR • drive wheel * More permitted rims on request 1) Rim 9x18 not permitted for 10 and 12 PR free rolling axle 90 • • • • • • 3,4 3,9 4,2 4,4 Speed (km/h) 40 1,0 900 1,5 1185 1,8 1330 2,0 1440 2,3 1500 2,5 1540 2,8 1570 3,1 1700 1290 1140 1700 1480 1900 1600 2060 1630 2145 1800 2200 2315 2430 1630 1190 2135 1565 2290 1750 2330 1890 2575 2110 2260 2455 2650 40 40 1700 1290 2235 1690 2500 1930 2710 2100 3020 2340 3230 2500 3490 2700 3750 2900 40 30 1830 1290 2405 1690 2750 1930 2980 2100 3320 2340 3550 2500 3840 2700 4125 2900 3160 3550 1830 1700 2405 2225 2750 2540 2980 2650 3320 2800 3550 2900 3840 3135 4125 3370 4350 3650 4875 2400 3150 3600 3750 3955 4090 4420 4750 5150 40 40 30 30 IMP cross-ply 126 A8 10 PR 139 A8 128 A8 8 PR 141 A8 142 A8 14 PR 154 A8 145 A6 12 PR 157 A6 152 A6 16 PR 164 A6 153 A6 14 PR 165 A6 ASFarmer 30 30 30 When fitted on tractor steering wheels, tyre load capacities are 80% of the loads for free-rolling applications. agricultural tyres 91 Multi purpose cross-ply tyre (MPT) Multi purpose cross-ply tyres (MPT) Tread patterns and recommended applications AS-Farmer Technical data Load capacities Tyre size Tread Permitted Tube WidthOuter Static Rolling pattern rims* and diameter loaded circum- Valve radius ference (TL-valve) (mm) (mm) (mm) (mm) PR LI Tyre load capacity (kg) at tyre pressure (bar) s ingle tyre fitment SS Speed 1,752,0 2,5 3,0 3,53,754,04,254,5(km/h) 275/80-18 MPT AS-Farmer9 x 18 TL 10.5-18 MPT 10.5/80-18 T 13.0/65-18 T 278 900 422 2660 36 G 16 10.5-20 T 275/80-20 MPT AS-Farmer9 x 20 TL 38 G 161) 278 9484442805 10.5-20 MPT (43 GS16)2) 12.5/14.5-20 T 335/80-20 MPT AS-Farmer 11 x 20 TL 38 G 161) 3401044 480 3055 12.5-20 MPT 11-20 SDC (43 GS16)2) 12.5/14.5-20 T 365/80-20 MPT AS-Farmer 11 x 20 ** TL 38 G 161) 3601092 503 3215 14.5-20 MPT 11-20 SDC (43 GS16)2) * More permitted rims on request 1) 92 MPT cross-ply Cross-ply off-road tyre for multi-purpose vehicles, tractors, loaders dumper trucks and off-road fork lifts, in agriculture, forestry and the construction industry. Valve 47 GW optional 2) 10 126 E 960 10601250143016101700 70 8 123 E 1010 1110 1330 1550 70 10 129 E 1370 1510 1700 1850 70 10 132 E 1560 1730 2000 70 ** higher than LI 132 consider rim load capacity Valve 50 GW optional 93 Garden tractor tyres Specially designed for garden tractors, large mowers and municipal tractors. AC 30 T 55/2 Robust tread pattern for construction vehicles. Garden tractor tyres Tread patterns and recommended applications IMP garden tractor B3 Lugged tread pattern for driven wheels. Central tread ridge for sickle bar mowers. Technical data Tyre size Tread Permitted Tube Width Outer Static loaded Dyn.rolling circum pattern rims* and diameter radius valve Roll Traction Roll Traction ference (mm) (mm) (mm) (mm) (mm) (mm) 6-6 6-6 T 55/24.00 E x 6 TT 145– 425 –192 – 41.5 G 70 B 3 5.375 I x 8 177 1345 18 x 7.00-8 450460 205210 TL 43 GS11.5 T 55/25.50 A x 8 178 1370 7.00 x12 23 x 8.50-12 B 37.00 I x12 TL43 GS11.5 214 575 – 260 – 1750 7 JA x12 7.00 I x15 234 – 710 – 3222160 TT43 GS16 28 x 9.00-15 AC 30 229 (6 1/2K x15) LI/SS PR 0,81,01,21,41,61,82,02,53,03,54,0 7.5-15 240/70-15 7.00 I x15 B 3 TL 28 x 9.00-15 T (6 1/2K x15) (28 x 9.00-15) 38 G 11.5 S 115 A 8 • 8 PR 450510580640710720770920 1020 1180 1215 * More permitted rims on request 94 227 721 – 322 – 2135 232 Tyre load capacity (kg) at tyre pressure (bar) Speed: 25 km/h1) 2 PR 4 PR 4 PR 6 PR 0,60,70,80,91,01,51,752,02,252,4 85 90 95 100 110–––––– – – 250270295325350455490605695775 – 6 PR 395425455480510650710760815850 – 1) 170185195210235280300325 – he following tyre load capacities apply to other maximum speeds: T at max. 20 km/h 112% of the table values at max. 30 km/h 93% of the table values at max. 40 km/h 75% of the table values (only for journeys to place of use) • drive wheel 95 Handcart tyres 652 B 11 Proven tread patterns in various sizes and load capacity levels for all transport equipment in warehouses and factories. Handcart tyres Tread patterns and recommended applications IMP handcart M 3 Rillen Technical data Tyre size Permitted PR Rim* Tube Tyre dimensions Tyre Tyre rims and Standard value load pressure valve Outer dia. Width capacity mm mmkg bar 210 x 65 210 x 65M 3 Rillen2 1.50-3 TT 28 G 90 210 70 1002,5 260 x 85/3.00-4 260 x 85652 22.10-4TT38 G 90 260 95 2002,5 28 G 90 14 x 4 14 x 4 (4.00-6) B 11 42.50 A x 6TT 90° 38 G 360 116 400 4,5 (350 x 100) GV 38/11.5 16 x 4 400 x100 (4.00-8) B 11 42.50 A x 8TT38 G 11.5 414 116 480 4,5 (400 x 100) 41.5 G 70 according to DIN 7809 96 * More permitted rims on request Max. Speed: 8 km/h 97 Operating instructions tractor tyres Load capacity and speed. When determining the minimum tyre size necessary for a vehicle, the approved axle load and the maximum design speed of the vehicle should always be used as the basis. Nominal load capacity = 100 % load, as indicated by the Load Index (LI), see page 5. In the case of twin-fitted driven wheels, a factor of 1.76 is applied to the load capacity of a single-fitted tyre. (tables on page 20 to 69 and 78 to 85) Tyre pressure. The tyre pressures given in the tables are minimum tyre pressures and should be used as a guide only. The given max. air pressures may not be exceeded. All tyre pressures refer to the “cold” tyre which has been standing outdoors for several hours, not exposed to intense sunlight. For twin fitments of radial t yres on tractors (to minimise ground pressure) a min. tyre pressure of 0.4 bar is allowed. Increase and decrease in load capacity Tractor radial tyres Speed (km/h) 10/ (only harvesters)1) 10/ (only front end loaders) 10 15 20 25 30 35 40 45 50 60 65 70 TractorSteering cross-ply tyres tyres The Static Loaded Radius is the distance between center of wheel and paved ground measured at reference load and pressure. Instead of W or W...L rims, the same size in DW or DWW may be used if the flange height is the same. (Designation of rims see pages 102 ff.) The Rolling Circumference (at reference load and reference pressure) is the distance a tyre covers with one revolution on paved surface. Measurement acc. to ISO 11795. The Speed Radius Index (SRI) is by convention a parameter used exclusively for calculation of theoretical speed of tractors. In no case SRI can be used as measurable value of rolling circumference. operating instructions Explanations referring to tractor tyres DA8 Load Load TyreLoadTyre Load Tyre capacity capacity pressurecapacitypressure capacity pressure (%) (%) (%) (%) (%) (%) (%) 170 170 130 1702) 130 1502)125 150 150 125 1402) 125 2002)125 150 150 125 140 125 1502)125 134 134100 130100 143 100 123 123100 120100 135 100 118,5111 100 107 100 115 100 115 107100 100100 100 100 112103100 90 100 90 100 109,5100 100 80 100 80 100 107 96100 – – – – 105 91100 – – – – 101,5– – – – – – 100––– –– – 91––– –– – 2) In service with cyclic loading operations and max. speed 10 km/h (6 mph) and hillside operation up to max. 11° (20%) slope! Only for tyres with at least 6 PR. 1) 2) 98 agricultural tyres 99 Operating instructions IMP / MPT tyres IMP = Implement tyres MPT= Multi purpose tyres Load capacity and speed. When determining the minimum tyre size necessary for a vehicle, the approved axle load and the maximum design speed of the vehicle should always be used as the basis. Nominal load capacity = 100 % load, as indicated by the Load Index (LI), see page 5. In the case of twin-fitted driven wheels, a factor of 1.76 is applied to the load capacity of a single fitment tyre. Tyre pressure. The tyre pressures given in the tables are minimum tyre pressures and should be used as a guide only. The given max. air pressures may not be exceeded. (tables on page 70 to 77 and 86 to 93) All tyre pressures refer to a “cold” tyre which has been standing outdoors for several hours, not exposed to intense sunlight. The static radius is for the new tyre laden at the max. load capacity and at the corresponding tyre pressure as per the table concerned. The rolling circumference corresponds to the max. load capacity (100%) and is inflated at the corresponding tyre pressure as per the table concerned. At 50% of the max. load capacity the rolling circumference is increased by approx. 1% for a radial tyre and by approx. 1.8% for a cross-ply tyre on the drive wheel of an agricultural tractor. Rims. Only the rims indicated in this data book are approved for fitting to new vehicle series. Load capacity increase and decrease for Implement Tyres with LI identification Load capacities for various maximum design speeds and for special applications Maximum speed in km/h (determined by vehicle design) Approved load capacity in % of the nominal load capacity according to Load Index for reference speed E (70 km/h) G (90 km/h) J (100 km/h) K (110 km/h) 120 –––– 115 –––– 110 – – – 100 105 – – – 100 100 – – 100100 95 – –101 101 90 –100102 102 85 –103103103 80 –104104104 75 – 105,5105,5 105,5 70 100107107107 65 105 108,5108,5 108,5 60 110110110110 55 111111111111 50 112112112112 45 113113113113 115115115115 401) 119119119119 351) 125125125125 301) 1) 135135135135 25 1) 150150150150 20 1) 165165165165 15 Application-restricted speed 180180180180 101) 210210210210 51) 1) 250250250250 Stationary 1) Twin tyre load capacity = 2 x single tyre load capacity. For other applications please contact tyre manufacturer. operating instructions Explanations referring to IMP/MPT tyres Implement Tyres with LI identification permitted tyre load capacity in % of given load capacity corresponding to load index and reference speed Speed free rolling axle drive wheel axle • (km/h) A6A8A6A8 0 165165235235 10 129140129140 15 121133121133 20 114126114126 25 107119107119 30 01120112 35 9510595105 40 900900 45 –95– 95 50 –90– 90 • • drive wheel free rolling mixed application When fitted on tractor steering wheels, tyre load capacities are 80% of the loads for free-rolling applications. 100 agricultural tyres 101 Rims and accessories Rims Rim flange: lateral support for the tyre bead Rim flange distance: rim width Rim bead seat: base on which the tyre bead is seated Rim well: inner side of the rim Rim diameter: specified rim diameter flange/bead seat Rim hump: continuous raised section of the rim bead seat which enables a better fitting of tubeless tyre beads at low pressure 2. Main types of rims Well-base rim: one-piece; deeper well for easier tyre fitting (5° tapered bead seat) (“x” in wheel size designation) e.g. 5.50 F x 16 9 x 18 Semi drop centre rim: split; the base is slightly deeper (5° tapered bead seat) (SDC designation of the wheel = Semi Drop Centre) e.g. 11-20 SDC 15° drop centre rim: one-piece; deeper well for easier tyre fitting (15° tapered bead seat) (”x“ in wheel size designation) e.g. 17.00 x 22.5 3. Wheel disc The wheel disc is the linking element between the rim and the axle hub. Of all the measurements for wheel linking lements - centre bore, bore diameter, e bolt holes and rim well depth (or offset) - the latter is an important dimension for the unimpeded movement of the tyre in any wheel position. (Rim offset = 0, when rim centre and hub contact area of the wheel disc are in line), On twin tyre fitments the distance between the rim centres would be twice the rim well depth plus twice the thickness of the wheel disc. Well-base rim Rim width in inches Flange type One-piece rim Rim nom. dia. in inches 5.50 F x 16 Wide rim W = (Wide) Rim width in inches One-piece rim Rim nom. dia. in inches W 12 x 24 15° drop centre rim Rim width in inches One-piece rim Rim nom. dia. in inches 17.00 x 22.5 4. Wheel strength For special cases the adequate rim strength must be confirmed by the rim manufacturer. 5.Lateral and true running of the wheels (without tyres) Both on fast vehicles and on large heavy wheels it is particularly important that the wheels are well-centred. On faster vehicles there should be as little radial and lateral run-out as possible on both bead/seat/flange sides of the rim, in order to achieve good quiet running. For fast commercial vehicles, both light and heavy, particularly low radial values may be necessary and these could be considerably below the specified standard maximum values. 6. Testing ring diameter d2 and size U Values for calibration of ball measuring tape. Wide rim with 2nd well base DW 14 x 26 DW = (double well) Rim width in inches One-piece rim Rim nom. dia. in inches rims 1. Important elements of the rim Examples of rims Semi drop centre rim Rim width in inches Multi-piece rim Rim nom. dia. in inches SDC = (semi drop centre) 11–20 SDC DIN: Deutsche Industrie-Norm (German Industrial Standard) 102 agricultural tyres 103 Rims and accessories Wide rims acc. to DIN 7823 for agricultural tractors W 6 up to W 13 W 8 L up to W 18 L Rim- contour W 9 228,5 51,0 ± 2,5 279,5 25,5 11,0 305,0 57,5 27,0 330,0 W 14 L W 15 L W 16 L 6° 254,0 203,0 20,551,0 22,5 254,0 6,5 355,5 16,0 57,5 ± 5,0 11,5 11,0 406,5 33,0 381,0 W 18 L 457,0 DW 10 254,0 15° DW 11 279,5 DW 12 ± 2,5 25,5 27,0 54,0 305,0 DW 13 330,0 DW 14 L 355,5 36,563,5 ± 5,0 18,0 406,5 404,271270,0 18 462,0 460,62 1447,1 20 512,8 511,42 1606,7 24 614,4 613,02 1925,9 DW 15 L 26 665,2 663,82 2085,5 DW 16 L 2245,1 DW 18 L 457,0 14,5 DW 20 B 508,0 41,0 8,0 DW 21 B 533,5 50,595,5 584,0 ± 6,5 29,0 21,0 - 15,0 635,0 28 716,0 714,62 381,0 30 766,8 765,42 2404,6 32 817,6 816,22 2564,2 34 868,4 867,02 2723,8 36 919,2 917,82 2883,4 DW 27 B 686,0 38 970,0 968,62 3043,0 DW 30 B 762,0 DW 23 B DW 25 B 42 1071,6 1070,22 3362,2 46 1173,2 1171,82 3681,4 48 1224,0 1222,62 3841,0** 50 1274,8 1273,42 4000,6 * Measuring ball 16 mm dia. without knurling. 104 γ min. 405,6 16 r1r2r5 203,0 W 8 L d1d2U Ø Ø ± 1,2 q W 8 W 10 L Code Ø f 152,5 W 13 Testing ring* e 178,0 22,510,014,523,5 44,5 9,5 W 11 Rim c 1,2min.max.min. min.max. max.max. deviation – 0,4 W 7 W 12 b Permitted + W 6 W 10 DW 10 up to DW 30 B a Nominal value ** ± 2,4 rims Wide rims acc. DIN 7823 for agricultural tractors ”L“-rims have a flange only 25.4 mm high (L = low) compared to 28.6 mm on the corresponding DW rims. By arrangement the tapered bead seat rims can be knurled: Distance between knurling a nd rim flange 9.5 ± 0.8 mm and base transition radius 1.6 mm min. Knurling depth max. 0.8 mm, projection compared to non-knurled bead seat min. 0.2 mm. Knurling distance 1.6 to 3.2 mm. DW-B rirns replace DW-A rirns and can be used with fuIl interchangeability. Rim measurements see table on page 105 agricultural tyres 105 Rims and accessories Well-base rims according to DIN 7818 for light c ommercial and agricultural vehicles Symmetrical well-base rim 3.00 D to 5.50 F Rims for garden tractors and implement applications (also DIN 7827) Asymmetrical well-base rim 5.50 F to 6.00 F 4.25 x 12 7.00 x 12 5 JA x 12 5.375 I 7.00 I Testing ring (16 mm) Rim d1d2 U a b c e f g p q r1r2r3 r4 r5 r6 size Per+1,2 Norminal value mitted min. min. min. max. max. min. max.min. ±1,2±1,5 – 0,4devia- 6.00–4 4.00 E-6 tion 3.00 D x 14 354,8 353,47 1110,5 14,2 17,828,7 31,8 17,512,2 +3,3 1812,4 13,08,1 0 3.00 D x 16 3.50 D x 16 88,9 15,7 34,0 34,9 405,6 404,271270,0 19,0 4.00 E x 16 101,6 19,9 35,014,2 8,6 38,0 4.50 E x 16 114,3 +4,1 23,4 22,0 39,719,812,4 0 18,0 13,6 4.00 E x 18 462,0 460,62 1447,1 101,6 1919,0 35,038,0 4.50 E x 20 512,8 511,42 1606,7 114,3 23,4 22,039,7 5.00 F x 16 405,6 404,27 1270,0 6,4 6,010 5.00 F x 18 462,0 460,62 1447,1 127,0 5.00 F x 20 512,8 511,42 1606,7 5.50 F x 15 380,2 378,97 1190,2 5.50 F x 16 405,6 404,27 1270,0 +2,3 22,212,9 23,927,614,525,454,015,6 9,7 0 139,7 5.50 F x 18 462,0 460,62 1447,1 5.50 F x 20 512,8 511,42 1606,7 6.00 F x 16 405,6 404,27 1270,0 152,4 28,6 1 +4,0 22,020,310,322,045,010,7 9,5 9,5 7 6 / K x 15 380,2 378,87 1190,2 165,1 19,6 11,0 0 2 106 agricultural tyres Testing ring (16 mm) Rim d1 d2 U a b c e f p q r1r3 r4 r5 Norminal Per- size value mitted devia- min. min. min. max. max.max.max. ±1,2 ±1,5 ±1,0 tion +1,5 4.25 x 12** 305,6 304,26 955,8 107,9 18,0 15 16,52720,04010,05,0 10 10 0 +5,5 7.00 x 12** 305,6 304,26 955,8 177,8 20,5 12 19,83130,06011,06,4 19 10* 0 5.375 I x 8 202,4 201,07 631,7 136,5 rims 3.00 D x 15 380,2 387,87 1190,2 76,2 see illustrations 7.00 I x 15 380,2 378,87 1190,2 177,8 +1,5 304,0 302,67 950,9 127,0 15,8 1)9 17,81952,838 8,1 4,3 15 10 0 4.00 E - 6 5 JA x 12 see illustrations 6.00 - 4 * for continuous manufacturing r5 = max. 12 mm allowed. 1) +1,2 – 0,4 ** only rims for agricultural tyres 107 Rims and accessories Drop centre rims according to DIN 7827 for Implement, MPT and Sand tyres Testing ring (16 mm) Semi drop centre rims (SDC) according to DIN 7826 for commercial and all-purpose vehicles and earth-moving equipment Rim d1 d2 U a b c e f p q r1r3 r4 r5 PerNorminal Per- size Norminal value mitted value mitted devia- devia- min. min. min. max. max.max.max. ±1,2 ±2,4 tion tion 9.00 x 15,3 388,3 386,98 1215,7 19,0 ±1,0 +5,525,0 34 50 0 9 x 18 462,0 460,82 1447,1 228,6 60 27,0 55 9 x 20512,8 511,42 1606,7 11 x 16 405,6 404,27 1270,0 25,4 +1,2 +4,0 -0,4 0 116,4 10 Testing ring (16 mm) Rim d1 d2 U a e f r3 r4 r5bcr1 size Norminal Permitted value min. min.max. ca. ca. ±1,2 min.±2,5 deviation Ø Ø ±1,2 11-20 SDC 279,4 ± 5 13 12-20 SDC 512,8 511,42 1606,7 304,8 5010 8 1025,41311 ±6 13 -20 SDC330,215 36.00 VA* 817,6 816,22 2564,2 914,4 ± 6 59,7 11 8 18 10 43,2 24,6 22,9 * standardised according to Tyre & Rim Association 11 x 20 512,8 511,42 1606,7 12 61 19 rims 11 x 18462,0 460,82 1447,1 279,4 31,8 31 13.00 x 17 330,2 436,6 435,221367,3 19,0±1,830,0 65 16.00 x 17 406,4* 13 x 20 330,2 +5,5 0 14 x 20 512,8 511,42 1606,7 355,6 25,4 +1,2 31,8 90 128,0 20 -0,4 17 x 20 431,8* * ± 4,7 108 agricultural tyres 109 Rims and accessories 15° drop centre rim according to DIN 78022 for commercial vehicles (agricultural vehicles with Code AG) Measuring ball Valves for tubeless fitting Valve description Valve- DIN ETRTOTRA* L hole dia. DIN 7780 Rim Testing ring (16 mm) Rim width Rim diameter d2 U a ep2*q* f h code designation code designation ±1,2 ±4,7 min. min. max. min. min. 15.5 393,71226,9 68 330,2 13.00 22.5 571,5 1785,4 70 19.5 495,31546,0 68 355,6 14.00 22.5 – 43 GS 11.5 49 GS 11.5 43 GS 16 V V V V 2-03-9 2-03-1 2-03-2 2-03-3 – TR 413 TR 414 TR 415 8,8 11,3 11,3 15,7 TR 618 A 16 59,0 42,5 48,5 42,5 16.00 22.5 406,4 17.00 22.5 431,834 62 30 11 18.00 22.5 571,5 1785,4 457,2 70 20.00 22.5 508,0 24.00 22.5 609,6 Valve accessories according to DIN 7757 An absolutely airtight valve insert is guaranteed only when the valve cap is screwed on firmly. This also acts as a protection against dirt. Dust caps (without seal) only provide a little protection. In many cases a valve extension is essential in order to be able to check the tyre pressure during use without having special examination, extensions and equipment. V 4-02-1 Insert for water filling 50MSW V 5-01-1 Valve base rims DIN 78026 * for AG rims: p2 = 82 mm and q = 70 mm DIN 7786 V 5-04-01 TR-J 650 Angled Valve Valve valve body body 80 DS 80 20,5 V 5-10-1 SP 2 Valve base Valve base Ask your valve manufacturer about valve extensions. Valve insert 20: For valves with normal bore. * Tire & Rim Association 110 agricultural tyres 111 Rims and accessories Application technology – Maintenance and care Valve description Valve- DIN ETRTOTRA* L hole dia. DIN 7774 38 G 11.5 38 G 16 V 2-01-1 V 2-01-2 TR 13 TR 15 11,5 16,0 35 35 Unused tyres should be stored in cool, dry, dark and lightly ventilated rooms. Tyres which are not fitted on rims should be stored standing up. Avoid contact with fuel, lubricants, solvents and chemicals. Fitting the tyre Particular care should be taken when fitting the tyre. Only rust-free rims of the right size should be used. These should not be dam aged or show any signs of wear and tear. The loose flange side should be examined carefully. DIN 7777 28 G-90 28 G-90 V 6-01-1 – – – – – 28 38 DIN 7773 V 4-02-1 Insert for water filling 47 GW V 4-01-1 Valve base TR 218 A 16 – DIN 7786 V 5-04-01 TR-J 650 Angled Valve Valve valve body body 80 GD 80 – SP 4000 Valve base Valve base For new tyres, always use new rubber tubeless valves or seals for tubeless metal valves, or new inner tubes and flaps. It is particularly important with large tyres that these should already fit on the rim flange with as little tyre pressure as possible. 20,5 Maintenance and care of the vehicle’s tyres and wheels An expert should always be called in to make a qualified judgement on the tyres and to carry out repairs. The high standard of quality of the tyres and vehicle, which is achieved by the measures and recommendations stated above, can only be ensured by regular checking of all factors. Tyres age as a result of physical and chemical processes and this may impair their performance. Regrooving of the tread pattern should be carried out only by qualified experts when the word “REGROOVABLE” or the symbol Ω is displayed on the tyre sidewall. When agricultural tyres are being fitted they may not be inflated to more than 150% of the max. tyre pressure. The pressure may not in any case exceed 2.5 bar. When MPT are being fitted they may not be inflated to more than 150% of the max. tyre pressure. The pressure may not in any case exceed 10.0 bar. Easy access to valves must be ensured at all times, even after they become soiled in use, to allow regular checking of the tyre p ressure. * Tire & Rim Association 112 Storage technology Valves for tubeless fitting agricultural tyres 113 Application technology – Filling the tyre with water Filling the tyre with water or anti-freeze solution Filling table (for one tyre) To ensure similar flexibility to air inflated tyres, only 70-75% of the tyre volume should be filled. This is achieved if the valve is rotated to its highest position and the tyre filled “to the valve”, as described Quantity when approx. 75% full Quantity when approx. 75% full Quantity when approx. 75% full Tyre size Cross-ply and radial Tyre size Cross-ply and radial Tyre size Cross-ply and radial Filling procedure After jacking up the vehicle, the tyre should be turned so that the valve is in its highest position. Instead of a valve, a combined water fill and draining valve (see illustration) is screwed onto the valve shaft. It has an opening at the side through which the air can escape while water is entering. The tyre is sufficiently full (70% to 75%) when the water comes out of the opening. A stirred anti-freeze solution, held in a container at a higher level, can be put into the tyre via a hose and the water fill valve. When filling with clear water, the hose from the water fill valve can be connected to the water supply. After filling the tyre, the original valve is reinstalled and the tyre is re-inflated to the normal pressure. Air – 25 % Water – 75 % “Hanauer Maus” combined device for filling and emptying water 114 “Waterboy” combined device for filling and emptying water agricultural tyres 7.5L–15 6.00–16 6.50–16 7.50–16 265/70 R16 MPT 285/80 R16 MPT 320/65 R16 15.0/55–17 425/55 R17 MPT 275/80–18 MPT 320/80–18 325/70R 18 MPT 365/70R 18 MPT 275/80–20 335/80–20 MPT 360/80–20 365/80–20 MPT 400/70–20 275/80 R20 MPT 280/85 R20 335/80 R20 MPT 375/70 R20 MPT 405/70 R20 MPT 420/65 R20 425/75 R20 MPT 445/65 R22.5 MPT 9.5–24 11.2–24 12.4–24 13.6–24 14.9/80–24 280/85 R24 320/70 R24 320/85 R24 340/85 R24 360/70 R24 380/70 R24 380/85 R24 405/70 R24 MPT 420/70 R24 420/85 R24 440/65 R24 445/70 R24 MPT 480/65 R24 480/70 R24 495/70 R24 MPT Litres (kg) 35 30 35 40 45 60 65 77 95 60 95 82 105 75 105 135 135 150 65 65 105 120 140 145 150 170 65 75 110 120 150 85 100 115 140 125 145 185 155 200 240 185 205 210 225 240 500/70 R24 IMP 500/85 R24 IMP 8.3–28 11.2–28 12.4–28 280/85 R28 320/85 R28 340/85 R28 380/70 R28 380/85 R28 420/70 R28 420/85 R28 440/65 R28 480/65 R28 480/70 R28 540/65 R28 600/65 R28 600/70 R28 9.5–30 16.9–30 380/85 R30 420/70 R30 420/85 R30 460/85 R30 480/70 R30 495/70 R30 MPT 500/85 R30 IMP 540/65 R30 600/65 R30 600/70 R30 620/70 R30 IMP 710/55 R30 710/60 R30 750/55 R30 8.3–32 9.5–32 12.4–32 650/75 R32 680/85 R32 800/65 R32 800/70 R32 900/60 R32 900/70 R32 1050/50 R32 16.9–34 380/85 R34 Litres (kg) 245 310 55 90 125 100 130 160 165 205 200 250 200 250 260 315 400 490 70 240 220 225 270 340 275 280 390 330 430 490 495 520 550 500 60 80 140 700 950 900 1000 1030 1200 1280 265 240 420/85 R34 460/85 R34 480/70 R34 500/85 R34 IMP 520/70 R34 540/65 R34 600/65 R34 650/65 R34 9.5–36 12.4–36 13.6 R36 340/85 R38 380/80 R38 420/85 R38 460/85 R38 480/70 R38 520/70 R38 520/85 R38 540/65 R38 580/70 R38 600/65 R38 650/65 R38 650/75 R38 650/85 R38 710/70 R38 800/70 R38 900/60 R38 9.5–42 480/80 R42 520/85 R42 650/65 R42 650/75 R42 680/80 R42 710/70 R42 710/75 R42 380/90 R46 480/80 R46 520/85 R46 380/90 R50 480/80 R50 Litres (kg) 290 380 310 445 355 360 465 600 95 160 180 215 240 320 420 340 395 530 420 550 500 630 750 900 800 1100 1200 110 460 580 650 740 1020 880 950 330 500 620 360 550 technology below. The table shows the filling quantities in litres per tyre. Any anti-freeze solution must be prepared in accordance with the manufacturer’s instructions. 115 Conversion table Conversion table Super Volume Tyres / Cultivation tyres Standard Wide base tyres RadialCross-ply Inch same rim 6.00-16 6.5-16 7.50-16 230/70-16 AS-Farmer 265/70 R 16 MPT AC70G 270/75-16 AS-Farmer 320/65 R 16 AC65 7.50-16 AS-Farmer 10.5-18 7.50-20 10.5-20 10.5 R 20 11.2 R 20 275/80-20 MPT AS-Farmer 275/80 R 20 MPT AC70G 280/85 R 20 AC85 12.5-20 12.5 R 20 335/80-20 MPT AS-Farmer 335/80 R 20 MPT AC70G 275/80-18 MPT AS-Farmer 6.00-16 6.5-16 7.50-16 325/70 R 18 AC70G 325/70 R 18 AC70G 9.5-24 9.5-24 AS-Farmer 11.2 R 24 280/85 R 24 AC85 12.4 R 24 320/85 R 24 AC85 13.6 R 24 340/85 R 24 AC85 14.9 R 24 380/85 R 24 AC85 16.9 R 24 420/85 R 24 AC85 11.2 R 28 280/85 R 28 AC85 12.4 R 28 320/85 R 28 AC85 13.6 R 28 340/85 R 28 AC85 14.9 R 28 380/85 R 28 AC85 16.9 R 28 420/85 R 28 AC85 14.9 R 30 116 6.00-16 AS-Farmer 6.50-16 AS-Farmer change of rim Inch 380/85 R 30 AC85 365/70 R 18 AC70G 365/70 R 18 MPT AC70G 8.3-24 AS-Farmer 375/70 R 20 MPT AC70G 405/70 R 20 MPT AC70G 420/65 R 20 AC65 9.5-24 AS-Farmer 335/80 R 20 MPT AC70G 375/70 R 20 MPT AC70G 405/70 R 20 MPT AC70G 420/65 R 20 AC65 365/80-20 AS-Farmer 320/70 R 24 HC70 360/70 R 24 HC70 405/70 R 24 AC70G 380/70 R 24 AC70G 380/70 R 24 HC70 440/65 R 24 AC65 420/70 R 24 AC70G 420/70 R 24 HC70 480/65 R 24 AC65 480/70 R 24 AC70G 480/70 R 24 HC70 540/65 R 24 AC65 11.2 R 24 12.4 R 24 280/85 R 28 AC85 380/70 R 28 HC70 440/65 R 28 AC65 420/70 R 28 AC70G 420/70 R 28 HC70 480/65 R 28 AC65 480/70 R 28 HC70 540/65 R 28 AC65/SVT 12.5-20 12.5 R 20 9.5-24 425/75 R 20 MPT AC70G 380/70 R 24 AC70G 380/70 R 24 HC70 420/65 R 20 AC65 420/70 R 24 AC70G 420/70 R 24 HC70 480/70 R 24 AC70G 480/70 R 24 HC70 540/65 R 24 AC65 10.5-18 7.50-20 10.5-20 10.5 R 20 11.2 R 20 8.3-32 AS-Farmer 13.6 R 24 9.5 32 Farmer AC 12.4-28 AS-Farmer 14.9 R 24 8.3-36 AS-Farmer 16.9 R 24 8.3-32 AS-Farmer 11.2 R 28 9.5-32 Farmer AC 12.4 R 28 8.3-36 AS-Farmer 13.6 R 28 9.5-36 AS-Farmer 12.4-32 AS-Farmer 14.9 R 28 16.9 R 28 420/85 R 28 AC85 480/70 R 28 HC70 540/65 R 28 AC65/SVT 420/70 R 30 HC70 agricultural tyres technology Standard tyres Wide base tyres Standard 14.9 R 30 117 Conversion table Conversion table (continuation) Super Volume Tyres / Cultivation tyres Standard Wide base tyres RadialCross-ply Standard tyres Wide base tyres Standard Inch same rim 16.9 R 30 420/85 R 30 AC85 18.4 R 30 460/85 R 30 AC85 14.9 R 34 380/85 R 34 AC85 16.9 R 34 420/85 R 34 AC85 18.4 R 34 460/85 R 34 AC85 13.6 R 38 340/85 R 38 AC85 16.9 R 38 420/85 R 38 AC85 18.4 R 38 460/85 R 38 AC85 20.8 R 38 520/85 R 38 AC85 18.4 R 42 480/80 R 42 AC85 20.8 R 42 520/85 R 42 AC85 18.4 R 46 480/80 R 46 AC85 20.8 R 46 520/85 R 46 AC85 480/70 R 30 AC70G 480/70 R 30 HC70 540/65 R 30 AC65/SVT 600/65 R 30 AC65 710/55 R 30 SVT 600/65 R 28 AC65/SVT 600/70 R 28 SVT 460/85 R 30 AC85 600/65 R 30 AC65 710/55 R 30 SVT 600/70 R 30 SVT 710/60 R 30 SVT 750/55 R 30 SVT 480/70 R 34 AC70G 480/70 R 34 HC70 540/65 R 34 AC65 520/70 R 34 AC70G 520/70 R 34 HC70 600/65 R 34 AC65 340/85 R 38 AC85 380/80 R 38 AC85 12.4-36 AS-Farmer 16.9 R 30 12.4-38 AS-Farmer 18.4 R 30 9.5-42 AS-Farmer 14.9 R 34 16.9 R 34 18.4 R 34 460/85 R 30 AC85 480/70 R 38 HC70 540/65 R 38 AC65 520/70 R 38 AC70G 520/70 R 38 HC70 600/65 R 38 AC65 13.6 R 38 16.9 R 38 650/75 R 32 AC70H/G 650/65 R 34 SVT 800/65 R 32 AC70H/N 800/70 R 32 SVT 1050/50 R 32 SVT 520/85 R 38 AC85 580/70 R 38 HC70 650/65 R 38 AC65/SVT 800/70 R 32 SVT 650/75 R 38 SVT 710/70 R 38 AC65/SVT 900/60 R 32 SVT 520/85 R 42 AC85 650/65 R 42 AC65 680/85 R 32 AC70G 650/85 R 38 SVT 650/75 R 42 SVT 710/70 R 42 SVT 800/70 R 38 SVT 900/70 R 32 SVT 900/60 R 38 SVT 580/70 R 38 HC70 650/65 R 38 AC65/SVT 650/65 R 42 AC65 Important: The indicated conversion possibilities are only for selection of tyre sizes with comparable outer diameter. In case of changing tyres a calculation of the wheel factor and the determination of the advance with the actual tire dimensions are in principle necessary. Please consider also the permissible rim sizes in accordance with our technical databook. 118 change of rim Inch agricultural tyres 18.4 R 38 380/90 R 46 AC85 20.8 R 38 380/90 R 46 AC85 18.4 R 42 480/80 R 46 AC85 380/90 R 50 AC85 20.8 R 42 380/90 R 50 AC85 18.4 R 46 480/80 R 50 AC85 20.8 R 46 technology 119 Notes 120 agricultural tyres 121 Sales organisations worldwide Sales organisations Europe D Sales organisations worldwide USA & Canada DK Mitas Tires North America, Inc. 7400 Carmel Executive Park, Suite 100 Charlotte NC 28226 USA Mitas GmbH Großer Kolonnenweg 23 Phone +49 511 936176-10 D-30163 Hannover Fax +49 511 936176-98 [email protected] NL B LUX Mitas Tyres B. V. Jagersveld 24 Phone +31 413 225 220 NL-5405 BW Uden Fax +31 413 225 226 [email protected] Central and South America MITAS a.s. Svehlova 1900/3 Contact person: CZ-106 00 Praha 10 Jiri Kotrc A Mitas GmbH Gregor-Mendel-Strasse 8-12 Phone +43 2252 50 86 84 A-2514 Traiskirchen Fax +43 2252 50 86 84-50 [email protected] Mitas, S. de R.L. de C.V. Mitas GmbH Station-Ost 9 Phone +41 41 210 82 00 CH-6023 Rothenburg Fax +41 41 210 82 01 [email protected] CZ MITAS a.s. Svehlova 1900/3 CZ-106 00 Praha 10 Phone +420 267 111 595 [email protected] Mitas Tyres S.L.U. MITAS a.s. Svehlova 1900/3 Contact person: CZ-106 00 Praha 10 Josef Hrdina Avda. de Somosierra, 12B 2° A Phone +34 91 490 44 80 E-28703 S.S. de los Reyes Fax +34 91 490 44 81 (Madrid)[email protected] F N MITAS a.s. Svehlova 1900/3 Contact person: CZ-106 00 Praha 10 Otakar Korbel S MITAS a.s. Sellukatu 5 D 23 Phone +358 3 345 0490 FIN-33400 Tampere Fax +358 3 345 0590 [email protected] Phone +44 0 1553 817740 Fax +44 0 1553 816531 [email protected] Mitas S.r.l. Via Vicolo del Caldo 20 210 47 Saronno (VA) P.Iva 02835660123 Phone +39 02 96 70 12 11 Fax +39 02 96 70 62 53 [email protected] I MITAS a.s. Svehlova 1900/3 Contact person: CZ-106 00 Praha 10 Vladimir Bartl RUS Mitas Ltd. Phone +420 267 111 550 Fax +420 271 750 214 [email protected] Phone +420 267 111 225 Fax +420 271 750 214 [email protected] addresses Unit 6, Bergen Way Business Park North Lynn Industrial Estate King’s Lynn GB-Norfolk PE30 2DD Phone +420 267 111 535 Fax +420 271 750 214 [email protected] Baltic States, Balkan States, Hungary, Greece, Slovenia IRL Mitas Tyres Ltd. Phone +52 449 153 23 50 Fax +52 449 153 23 53 [email protected] Poland, Belarus, Ukraine, Moldova, Slovakia, Kazakhstan, Uzbekistan, Kirgistan, Turkmenistan, Tajikistan, Mongolia, Kaliningrad, Georgia, Azerbaijan, Armenia Mitas 8 rue Louis Neel Phone +33 3 80 28 06 95 F-21000 Dijon Fax +33 3 80 28 06 99 [email protected] FIN Torre Plaza Bosques Desp. 502 Av. Universidad # 1001 Col. Bosques del Prado C.P. 20127 Aguascalientes, Ags. Mexico Turkey, Arabic States, Asia, Australia, New Zealand, African States P E 122 Phone +420 267 111 540 Fax +420 271 750 214 [email protected] Mexico CH GB Phone +1 704 542 3422 Fax +1 704 542 3474 [email protected] 3rd Tverskaya Yamskaya 36/40, Phone +7 499 9787631 Off. 91 Fax +7 499 9787631 125047 Moscow [email protected] agricultural tyres 123 MITAS_10/2013 Subject to technical amendments, printing errors and mistakes in text or illustrations. © MITAS a.s. www.mitas-tyres.com Distributor / customer service Further information: www.mitas-tyres.com Produced and Engineered by
© Copyright 2024