FRYBABY2 Compact Burn-in Generator Made in USA FRYBABY2 Compact Burn-in Generator 2 Copyrights & Trademarks © Copyright Hagerman Audio Labs 2014. All rights reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent. Disclaimer The information contained in this document is subject to change without notice. Hagerman Audio Labs shall not be liable for errors contained herein or for consequential damages in connection with the furnishing, performance, or use of this material. Warranty Hagerman Audio Labs warrants this product free of defects in materials and workmanship for a period of 10 years. If you discover a defect, Hagerman Audio Labs will, at its option, repair or replace the product at no charge to you provided you return it during the warranty period, transportation charges prepaid to Hagerman Audio Labs. This warranty does not apply if the product has been damaged by negligence, accident, abuse or misuse or misapplication, has been damaged because it has been improperly connected to other equipment or has been modified without the express written permission of Hagerman Audio Labs. This warranty is limited to the replacement or repair of this product and not to damage to equipment of other manufacturers. Any applicable implied warranties, including warranty of merchantability, are limited in duration to a period of the express warranty as provided herein beginning with the original date of purchase and no warranties, whether express or implied shall apply to the product thereafter. Under no circumstances shall Hagerman Audio Labs be liable for any loss, direct, indirect, incidental, special, or consequential damage arising out of or in connection with the use of this product. Hagerman Audio Labs PO Box 61911 Honolulu, HI 96839 808-383-2704 www.haglabs.com FRYBABY2 Compact Burn-in Generator 3 Description The FryBaby2 audio system conditioner is a burn-in signal generator designed especially for cables and interconnects. It can also be used to burn-in linestages, phonostages, and amplifiers. The sophisticated electronic waveform – a combination of wideband noise and variable frequency amplitude modulation – is designed to exercise both low and high frequency characteristics of conductors and insulators. Specifications Item Output Voltage Current Limit Signal Bandwidth AC Voltage Specification 1Vrms (LINE), 10mVrms (MM), 1mVrms (MC) 10mA 10Hz to 1MHz 120V/240V FRYBABY2 Compact Burn-in Generator 4 Operation The FryBaby2’s control knob sets the mode of operation. MC selects an output level suitable for driving moving coil phonostage inputs (-60dB), MM for moving magnet phonostages (-40dB), and ON for everything else (line level). The internal LED blinks at the rate of modulation. There are two modes of cable burn-in, voltage and current. Both are required for maximum effectiveness. Voltage Mode In voltage mode the cable dielectric is excited by electric fields. Leave the far end of the cable open-circuited (see diagrams in following section). Current Mode In current mode, the cable is short circuited, and conductors are exercised via magnetic fields. Short-circuit the far end of the cable or form a loop by returning the cable to the other FryBaby2 output. Current mode is not applicable when using the FryBaby2 to burn in amplification. Duration It is best to do a voltage burn for 24 hours followed by a current burn for 48 hours. Note: silver conductors typically take twice as long! FRYBABY2 Compact Burn-in Generator 5 Connections The FryBaby2 is designed to burn-in and condition cables offline. It can also be used as a signal generator to break-in amplifiers or other electronics. RCA The FryBaby2 can burn in a stereo pair of interconnects by using the female-tofemale adapter at the far end. First, do a voltage burn by connecting the interconnect pair directly to the FryBaby2 outputs. Set to ON. After the voltage burn, do a current burn by inserting the adapter to close the loop. Phonostage, Linestage, Amplifier Amplification electronics are burned in using voltage mode. Connect the FryBaby2 outputs to the inputs on your phonostage (you’ll need an interconnect). Set the output amplitude to either MC or MM, depending on the gain of your phonostage. This sets the burn-in signal to the correct amplitude and equalization. For linestages or other types of amplifiers, use the ON level output. Amplifier must be powered on. Troubleshooting If the LED is not lit, check the power supply and rotary switch. R01 100 BO C+ C- OS LV 01 02 04 07 06 J01 9V 03 08 VO 05 U01 TC7660S D01 1N4148 S01A C06 47uF D02 1N4148 C03 47uF 9V C07 47uF C04 47uF R02 47k Q01 2N3904 C08 100nF R05 100k C05 47uF C09 47uF R07 10k 3 2 4 R04 100k R03 10k 1 R06 10k 7 R08 10k 13 14 15 C10 47uF 5 9V 8 6 11 U02A LM13700 16 PO Box 61911 Honolulu, HI 96839 Hagerman Audio Labs 6 11 9V 10 C11 100pF 12 U02B LM13700 SIGNAL 9 MODU R10 10k R09 4.7k VCC R12 100k R11 100k C12 47uF R13 47k 3 2 R14 100k 5 6 9V 9V 1 U03A LM358 7 U03B LM358 R16 100k R15 100k Q02 2N3904 R17 100k R18 47k 5 6 C13 100nF 9V 7 U04B LM358 9V R22 100k R21 47k 9V 1 U04A LM358 PO Box 61911 Honolulu, HI 96839 Hagerman Audio Labs R20 100k R19 100k 3 2 MODU D03 LED R23 2.2k SIGNAL C15 3.3nF R26 1M C16 47uF R28 100 R27 1k C14 1nF R25 100k R24 10k 9V C01 1nF S01B C17 47uF R31 10k R32 10k 3 2 R33 10k 5 6 R30 10k 9V 9V 1 U05A NE5532 7 U05B NE5532 R35 10k R37 100 R34 10k R36 100 J03 J02 PO Box 61911 Honolulu, HI 96839 Hagerman Audio Labs C19 47uF C18 47uF
© Copyright 2024