CAPTIVATION 0-10V Relay Load Controller Simplifies adding lighting controls to existing projects The Philips Captivation family of products helps alleviate the often complex and cost-prohibitive hurdle of adding lighting controls to a facility. Captivation controllers can be used as stand alone circuit controllers with off-the-shelf switches, or networked with Philips Dynalite products into an area, building or campus-wide lighting system. The Captivation 0-V Relay Load Controller is rated for incandescent, magnetic low-voltage, electronic low-voltage, magnetic fluorescent driver and general purpose switching, including plug loads. 210.1 mm (8.27 in) 200.2 mm (7.88 in) 17 mm (.66 in) 70.9 mm (2.79 in) 191.7 mm (7.5 in) 69 mm (2.7 in) 104.8 mm (4 in) • Flexible control — Allows 16 A switching and/or 0-10V (ANSI C82.11) dimming control of any 120V and 277V lighting circuit. 48.2 mm (1.9 in) 94 mm (3.7 in) • Control to the user — Utilizes user selectable standard dimming curves and custom user curves for maximum dimming operation across loads. • Convenient mounting — Mounts on to any contractor supplied deep back box. • Naturally ventilated — Integral ventilation means that no forced cooling is required, thereby reducing maintenance. • 100% compliance — Accommodates ‘freeair’ or piped low voltage control wiring to meet with US and Canadian national code requirements. • Three dry-contact inputs — Software configurable, allowing third-party devices to operate the Captivation controller in standalone mode, or to allow bridging of devices onto a DyNet network. • UL924 — Programmable UL924 rated input on each device for emergency use. • Motion sensor input — Included power supply allows for direct connection of a +24 VDC motion sensor or Dynalite sensor. • User control selection — Via DyNet or DMX512. For detailed product information, please refer to the product information pages at www.philips.com/lightingcontrolsna. Electrical Diagram Specifications Due to continuous improvements and innovations, specifications may change without notice. Details Input Voltage 120 VAC and 277 VAC (+10% / -15%), 50 / 60 Hz, Dedicated Single Phase branch device. Max 20 A Power Supply Output Supply: 120 – 277 VAC 600W 50/60Hz Single Phase LINE IN (Black) NEUTRAL (WHITE) EARTH (GREEN) LOAD OUTPUT (RED) 60 mA @ 24 VDC for external device power 80 mA @ 24VDC for devices on the DyNet bus 8.27” x 4.0” x 2.7” (210.1 mm x 104.8 mm x 70.9 mm) Construction 16 gauge galvanized steel Operating Conditions Temperature: 32 to 122° F (0 to 50° C) ambient Humdity: 10 to 95% non-condensing (indoor application only) Storage & Transport Temperature: -13 to 140° F (-25 to 60° C) ambient Humidity: 10 to 90% non-condensing Standard Product - 0-10 + Relay 1 Circuit 0-20 + Relay 1 Circuit (meeting City of Chicago Plenum requirements) Options & Ordering Additional spare box mounting ring (1 included with FCC Part 15A, UL916, cUL916, CSA 22.2 No 205, California Title 24 Section 119, 2008 as part of a Dynalite system, RoHS Compliant, ANSI C82.11 Dimming Compliant, Air sealed model available to meet City of Chicago Plenum requirements. DC-DRD-I-1C-101 (Philips 12NC - 913701254501) DC-RING-001 (Philips 12NC - 913701254902) each controller) Additional spare low voltage wire protection grommet (1 included with each DC-GROMMET-001 (Philips 12NC - 913701254802) controller) Captivation Handheld DMX Addressing Unit +24VDC (60mA) GND Motion µP SHLD MOTION GND +24VDC SW1 CONTACT INPUTS SW2 2 X RJ24 SW off GND GND Wiring Diagram Load Wiring Black - 120V/277V Line Input Red - Load Output to Fixtures White - Neutral Green - Ground J13: * TE = Trailing Edge (Reverse Phase) Dimming * LE = Leading Edge (Forward Phase) Dimming + - +24V 24V+ (60mA) MOTION GND Default jumper states shown DMX default address = 1 J13 Only applicable to DC-DPD J9 Only applicable to DC-DRD +24V +24V DyNet DATADMXDyNet DATA+ DMX+ DyNet GND DMX GND GND SHLD SHLD 24V+ SW1 SW2 SW off DYNET/DMX DYNET/DMX IN or OUT IN or OUT GND Captivation QG.4 7/16/2014 Load Compatibility Load Type DC-DRD-I-1S-101 (Philips 12NC - 913701252801 UL924 TRIGGER DYNET/DMX IN or OUT Dimensions (H x W x D) GND J17 CAT5/CAT6 with RJ45 terminations or 18-22 AWG twisted pair RS485 compatible cabling to press release terminals TRIG DMX TERM ON OFF Data Wiring TRIG DD+ J18 Flying leads Line, Load, Neutral and Ground +24VDC DMX GND(ISO) ON OFF Power Wiring +24VDC GND DIM J13 TYPE Linear (fluorescent) Modified Linear (LED) Off +24VDC SHLD LE TE FWD REV PHSE PHSE Operational Control Curves Compliance DyNet RS485 External device 24 VDC power to standalone sensors (60 mA max) 3 dry contact inputs (SW1, SW2, SWOFF) Motion input - active high +24 VDC from sensor (wet contact) UL924 triggers DyNet panic preset 65,534 0 - 10 V dimming terminals routable as Class 1 or Class 2 Configuration DMX TERM SHLD Service button Test button Factory set button Configuration and monitoring via Philips Dynalite EnvisionManager software. Programming via Philips Dynalite EnvisionProject software. On SHLD 0 - 10 V dimming control capable of sourcing or sinking 40 mA. Can be wired as Class 1 or Class 2 circuit. DMX512 input connection DyNet connection Certification GND 0-10V Control Low Voltage Connections DMX GND (ISO) Off GND UL924 TRIGGER User Controls On DD+ MOTION Dimming Control +24VDC Rated for incandescent (tungsten & halogen), magnetic lowvoltage, electronic low-voltage, magnetic fluorescent driver and general purpose switching (incuding plug loads) CONTACT INPUTS Output Load Control Physical - 0 – 10V Control (Grey) +24VDC Relay contact rated at 16 A @ 120 V & 10 A @ 277 V Control + 0 – 10V Control (Purple) 0-10V J9 Electrical Specification DYNET/DMX IN or OUT Item @ 120 V 50/60 Hz @ 277 V 50/60 Hz Resistive Load 16A 10 A Tungsten Lamp 16A 10 A Magnetic Driver 16A 10 A Electronic Driver 16A 10 A Magnetic Halogen 16A 10 A Electronic Halogen 16A 10 A Horsepower 1HP 2 HP DL-CP-ZIPPY-NA Philips Lighting North America 200 Franklin Square Dr Somerset, NJ, United States Philips Lighting Canada 281 Hillmount Road Markham, Ontario L6C 2S3 Tel: 1-800-526-2731 Canada Specifications subject to change without notice. © WMGD Pty Ltd Trading as Dynalite. Unit 6, 691 Gardeners Road Mascot 2020 Australia. ABN 33 097 246 921. All rights reserved. Dynalite, DyNet and associated logos are the registered trademarks of WMGD Pty Ltd. Not to be reproduced without permission. Email: [email protected] Web: www.philips.com/lightingcontrolsna CAPTIVATION 0-10V Nov-14
© Copyright 2024