1. No category

Carburetor & Fuel Injection
Co
Cadillac
Johnson Carburetor Needle & Seat, 1923-
Co
Cadillac
25 V8
Johnson Carburetor Throttle Shaft
Bushing, 1920-31 V8
$36.25
CAD-0133-A
High strength viton tip carburetor
needle and brass seat for early 1920's
V8 Cadillac. Used on 1923 - 1925
Type V63. May also fit other years
and models.
$11.50
CAD-0131
Brass carburetor throttle shaft bushing
for V8 Cadillac and LaSalle from
1920 - 1931. Cadillac part number
50761, group number 12.0117 "Collar
on automatic throttle shaft".
Needle
Material: Steel, viton; OAL: .718;
Length: .578 excluding viton tip;
Width: .200 flat to flat; Width: .246
corner to corner
For use on Cadillac: 59, 61, 63, 314,
341, 353, 355A
For use on LaSalle: 303, 328, 340,
345A
Seat
Material: Brass; Finish: Natural;
Thread: 7/16-24; Thread length: .375;
Hex: .4375; OAL: .600; ID Bottom:
.250; ID Top: .125
Co
Cadillac
Johnson Carburetor Accelerator Pump
Leather Plunger, V8 V12 V16
$15.50
CAD-0040
Formed leather cup for the accelerator
pump plunger as used on CadillacJohnson carburetors on the following
models of Cadillac V-8, V-12 and V-16
and LaSalle V-8: 59, 61, 63, 303, 314,
328, 340, 341, 345, 353, 355 A B & C,
370 A, 452 A. Cadillac part number
50691, group number 12.0278.
OD: 1.500; Height: .437; Thickness:
.090; Hole: .200
Co
Cadillac
Johnson Carburetor Air Vent Nozzle
Gasket, -8
$4.25
CAD-0042
Paper gasket for carburetor to air vent
nozzle joint on Cadillac-Johnson
carburetors as used on: Cadillac V-8
1914-1915 and 1927-1930 LaSalle V8 1927-1930. Cadillac group number
12.0580, part number 53283.
Length: 1 3/8; Width: .791; Large hole
ID: 1/4; Small hole ID: .168
Version 11/20/2014
Material: Brass; OD: .375; ID: .3125;
Height: .497
Co
Cadillac
Johnson Carburetor Throttle Shaft, Early
V8
$46.50
CAD-0130
Throttle shaft for Cadillac Johnson
carburetors as used on 1920 - 1925
Cadillac V8. Cadillac part number
26520 (Shaft only, part of shaft lever
assembly), group 12.0148.
Material: Brass; Finish: Natural;
Thread: 4-36; Length: 4.156; OD:
.312; Slot: 2.453 x 0.072; End hole:
.128; Mid hole: .116
Co
Cadillac
Johnson Carburetor Bottom Float Bowl
Gasket, V8 V12 V16
$2.50
CAD-0038
Die cut cork gasket to seal bottom of
float bowl to carburetor main body on
Cadillac Johnson carburetors. For use
on Cadillac V-8, V-12 and V-16 as well
as LaSalle V-8. Cadillac part number
50732, group number 12.0045.
ID: .935; OD: 1.250; Thickness: .062
Co
Cadillac
Johnson Carburetor Bowl Gasket, V8
$12.50
CAD-0047
Die cut cork gasket to seal top of float
bowl to carburetor body. For use on
1933 Cadillac and LaSalle V-8.
Cadillac part number 891176, group
number 12.0045.
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
1
Carburetor & Fuel Injection
Co
Cadillac
Johnson Carburetor Float, V8 V12 V16
Co
Cadillac-Johnson
Carburetor Screw Gasket, 1932-
$51.50
CAD-0019
Urethane foam carburetor float to fit V12 and V-16 Cadillacs and 1927-1931
Cadillac and LaSalle V-8 with CadillacJohnson carburetors. This float can
also be used on 1923 - 1925 V8
model V63. Ready for installation.
Cadillac part number 888780, group
number 12.0666.
33 V8
Co
Cadillac
Johnson Carburetor Float Bowl Gasket,
V8 V12 V16
Material: Hard fiber; OD: 9/16; ID:
5/16; Thickness: 1/32
$12.50
CAD-0037
Die cut cork gasket to seal top of float
bowl to carburetor body on Cadillac
Johnson carburetors. For use on
Cadillac V-8, V-12 and V-16 as well as
LaSalle V-8. Cadillac part number
50736, group number 12.0045.
Co
Cadillac-Johnson
Co
Cadillac
Johnson Carburetor Float, 1932-35 V8
$67.00
CAD-0049
Cadillac-Johnson carburetor float for
use on 1933 LaSalle and Cadillac V8. This urethane foam float will not
absorb gasoline or change dimension.
Cadillac part number 877694, group
number 12.0666.
ID: 1.500; OD: 3.032; Thickness: .970;
From flat side to opposite: 2.600
Co
Cadillac
Johnson Carburetor Fuel Inlet Gasket, V8
$4.25
CAD-0045
Paper gasket for use between the
carburetor and fuel inlet nipple on
Cadillac-Johnson carburetors as used
on 1933 Cadillac and LaSalle V-8.
Cadillac group number 12.0715, part
number 891158.
Center ID: .730; Attachment holes ID:
.255; Length: 1.794; Width: 1.173
$1.25
CAD-0083
Hard fiber gasket used with the 5/1618 x 11/32 screw in carburetor body
above the inlet fitting on CadillacJohnson carburetors as used on 19321933 Cadillac and LaSalle V8.
Cadillac part number 891148, group
number 12.0355.
Carburetor Lever Arm Spring,
1932-33 V8
$8.25
CAD-0086
Retracting spring for the auxiliary air
adjusting arm used on CadillacJohnson carburetors installed on 19321933 Cadillac and LaSalle V8.
Cadillac part number 891551, group
number 12.500.
Material: Stainless steel; Finish:
Natural; OD: .350; LOA: .920; Wire:
.046
Co
Cadillac
Johnson Carburetor Intake Fitting
Lockplate, V8 V12 V16
$10.50
CAD-0050
Steel lockplate to secure carburetor
intake nipple on Cadillac-Johnson
carburetors as used on the following
models of 1927-1930 Cadillac &
LaSalle V-8, V-12 and V-16: 303, 328,
340, 341, 345 A, 353, 355 A, 370 A,
452 A.
Note: 2 required per car on Cadillac V12 and V-16 Models 370 A and 452 A.
Cadillac group number 12.0720, part
number 881875.
Main body OD: 1.056; Hole ID: .208;
Point to point on star: 13/16;
Thickness: .063; Length: 1.369
Co
Cadillac
Johnson Carburetor Air Pump Stud, V16
$10.50
CAD-0149
Steel stud with 10-32 threads. For use
on the carburetor air pump of 1930 1931 Cadillac V16. Heat treated to
grade 8 for excellent durability.
Material: 4140, heat treat grade 8;
Finish: Natural; Thread: 10-32; Thread
length: .650; OAL: 2.718; OD: .1875;
Mid: 1.418
Version 11/20/2014
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
2
Carburetor & Fuel Injection
Co
Cadillac
Johnson Carburetor Intake Silencer
Gasket, V8 V12 V16
Co
Cadillac
$8.25
CAD-0046
Paper gasket for carburetor to intake
silencer joint. For use on 1933
Cadillac and LaSalle V-8 and 1931-31
V-12 and V-16.Cadillac part number
888898, group number 12.0935.
$31.00
CAD-0052-A
Viton tipped carburetor needle and
brass seat for use with CadillacJohnson carburetors as used on 193235 Cadillac & LaSalle V8.
Material: Gasket paper; Length: 4.250;
Width: 3.437; Thickness: .032; ID
Hole: 2.625; Mount hole & center: .350
DIA, 3.500 center
Co
Cadillac
Johnson Carburetor Manifold Gasket, V8
$8.25
CAD-0041
Paper gasket for carburetor to intake
manifold joint for Cadillac-Johnson
carburetors on Cadillac V-8 19201932 and LaSalle V-8 1927-1933.
Cadillac group number 12.0021, part
number 50737.
Johnson Carburetor Needle & Seat, 1932-
35 V8
Needle: Cadillac part number 891146,
group number 12.0648; Seat: Cadillac
part number 891661, group number
12.0649.
Needle: Material: 303 SS with Viton
tip, Length: 3/4, DIA.: .230
Seat: Material: Brass, Thread: 7/1620, Thread length: 5/8, OAL: 3/4, Hex:
7/16, Inlet hole ID: .120
Co
Cadillac
Johnson Carburetor Repair Kit, 1927-31
V8
Length: 4.500; Width: 3.187; Hole:
2.200; Mounting hole DIA & center:
.465, 3.580
Co
Cadillac
Johnson Carburetor Throttle Lever Stop
Screw, 1925-33 V8
$6.25
CAD-0085
Stainless steel stop screw for CadillacJohnson carburetors as used on
1925 - 1933 Cadillac and LaSalle
V8's. This is the stop screw for the
throttle and choke lever. Cadillac
group number 12.0195, group number
58552X.
Material: Stainless steel; Finish:
Natural; Thread: 10-24; OAL: 5/8;
Length under head: 5/16; Head height:
5/16; Head OD: 5/16; Slot: .050 x .08
$168.50
CAD-0069-K
Repair kit for Cadillac-Johnson
carburetors used in V-8 Cadillac and
LaSalle from 1927-1931. This kit
contains one each of the following:
Needle, Seat, Float, Float bowl
gasket, Bottom float bowl gasket,
Throttle pump leather plunger,
Carburetor to manifold gasket,
Carburetor to air vent nozzle gasket,
Carburetor to spray nozzle gasket,
Lock for carburetor inlet nipple,
Leather seat for auxiliary air valve,
Seat gasket 1/64 (Qty. 4), Seat gasket
1/32 (Qty. 4), Carburetor to fuel inlet
nipple gasket, Carburetor intake
silencer gasket (Used on all 345A &
355A and some 340 & 353)
Kit will service LaSalle Models: 19271928 303, 1928-1929 328, 1929-1930
340, 1930-1931 345 A
Cadillac Models: 1927-1929 341,
1929-1930 353, 1930 1931 355A
Version 11/20/2014
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
3
Carburetor & Fuel Injection
Co
Cadillac
Johnson Carburetor Repair Kit, 1923-1925
Co
Cadiilac
Johnson Carburetor Small Bowl Gasket,
V8
V8
$194.00
CAD-0132-K
Repair kit for Cadillac Johnson
carburetors as used on 1923 - 1925
Cadillac V8 Model V63.
$2.25
CAD-0048
Die cut cork gasket to seal bottom of
float bowl to carburetor main body on
Cadillac-Johnson carburetors. For
use on 1933 LaSalle and Cadillac V8.
Cadillac part number 891160.
Kit contains one each of the following:
Float, Float bowl gasket, Bottom float
bowl gasket, Throttle pump leather
plunger, Manifold gasket, Air vent
nozzle gasket, Spray nozzle gasket,
Leather seat for auxiliary air valve,
Needle valve gasket (Qty. 4), Seat
gasket (Qty. 4), Throttle shaft, Needle
and seat, Filter cover gasket
Co
Cadillac
Johnson Carburetor Repair Kit, V12 V16
$161.00
CAD-0079-K
Repair kit for Cadillac-Johnson
carburetors used in 1930 and 1931 V12 and V-16 Cadillac models 370A
and 452A.
Kit contains one each of the following:
Float, Needle, Seat, Float bowl
gasket, Carburetor bottom float bowl
gasket, Throttle pump leather plunger,
Carburetor to spray nozzle gasket,
Throttle pump body gasket, Intake
silencer gasket, Lock for carburetor
inlet nipple, Leather seat for auxiliary
air valve, Needle valve seat gasket
1/64 (Qty. 2), Needle valve seat
gasket 1/32 (Qty. 2), Carburetor to fuel
inlet nipple gasket, Carburetor to
manifold gasket.
Co
Cadillac
Johnson Carburetor Repair Kit, 1932-35
ID: 1.062; OD: 1.375; Thickness: .062
Co
Cadillac
Johnson Carburetor Spring Nozzle
Gasket, V8 V12 V16
$2.25
CAD-0043
Paper gasket for spray nozzle to
carburetor body joint on Cadillac and
LaSalle. Cadillac part number 50739,
group number 12.0630.
Length: .775; Width: .500; Thickness:
.032; Hole: .281
Co
Cadillac
Johnson Carburetor Throttle Body
Gasket, V8
$8.25
CAD-0044
Paper gasket for use between the
carburetor and throttle pump body on
Cadillac-Johnson carburetors used
on: Cadillac V-8 1932-1933; LaSalle V8 1932-1933. Cadillac group number
12.0255, part number 891170.
Center port: 9/16 x .362; Hole ID: .230;
Length: 1.178; Width: .845
V8
$162.00
CAD-0070-K
Repair kit for Cadillac-Johnson
carburetor used on V-8 Cadillac and
LaSalle 1932-1935.
Kit contains one each of: Needle,
Seat, Float, Throttle pump leather
plunger, Carburetor to manifold
gasket, Spray nozzle gasket, Throttle
pump body gasket, Carburetor to fuel
inlet nipple gasket, Intake silencer
gasket, Float bowl gasket, Carburetor
body screw gasket (not shown),Seat
gasket 1/64 (Qty. 2), Seat gasket 1/32.
Kit will service LaSalle 1932 345 B;
1933 345 C
Cadillac 1932 355 B; 1933 355 C;
1934-1935 355 D
Version 11/20/2014
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
4
Carburetor & Fuel Injection
Co
Cadillac
Johnson Carburetor Needle & Seat, V12
V16
$31.00
CAD-0026-A
High strength Viton tip carburetor
needle and brass seat to fit all V-12
and V-16 Cadillacs using a CadillacJohnson carburetor.
Seat
Cadillac part number 883524, group
number 12.0649.
Needle
DIA: .275 corner to corner; OAL: .780
Seat
Hex: 7/16; OAL: .600; Thread: 7/1620; Thread length .375
Material: Gasket paper; ID: 2 15/16;
OD: 3 7/16; Length across: 4 7/16;
Stud hole DIA: 3/8
Co
Cadillac
Johnson Carburetor Fuel Inlet Filter
Cover Gasket, 1922-27 V8
Johnson Carburetor Needle & Seat, 1927-
31 V8
$36.25
CAD-0028-A
High strength Viton tip carburetor
needle and brass seat to fit 1927-31 V8 Cadillacs using a Cadillac-Johnson
carburetor.
Needle
Cadillac part number 375054, group
number 12.0648.
$5.25
CAD-0137
Laser cut paper gasket for the fuel
strainer housing on early Cadillac V8.
Cadillac part number 53083, group
number 12.0837.
For use on the following:
1922-23 Model 61
1923-25 Model 63
1925-27 Model 314
Material: Gasket paper; OD: 1.750; ID:
1.4375; Thickness: .030
Seat
Cadillac part number 876246, group
number 12.0649.
Co
Cadillac
Needle
DIA: .275 corner to corner; OAL: .780
Seat
Hex: 7/16; OAL: .600; Thread: 7/16-20
Co
Cadillac
Johnson Carburetor Intake Silencer
Gasket, Early V8
$8.25
CAD-0046-B
Gasket for use between the intake
silencer and connecting pipe on
Cadillac-Johnson carburetors. Used
on some V-8 Cadillacs and LaSalles
from 1929-30, models 340 & 353.
Used on all V-8 Cadillacs and
LaSalles from 1930-31, models 345A
and 355A. Cadillac part number
886831, group number 12.0935.
Listed in Cadillac parts book as
"Gasket between intake silencer and
connecting pipe".
Needle
Cadillac V-16 part number 883489,
group number 12.0648.
Co
Cadillac
Co
Cadillac
Johnson Carburetor Fuel Inlet Nipple, V16
$36.25
CAD-0104
Stainless steel fitting for use in
connecting the carburetor to the fuel
inlet. For use on 1930 and 1931
Cadillac V16. Cadillac part number
881313, group number 12.0711.
Johnson Carburetor Needle Clip V16
$7.75
CAD-0031
Annealed stainless spring steel clip for
use on V-16 Cadillacs using CadillacJohnson carburetors. Cadillac part
number 894474, group number
12.0657.
Version 11/20/2014
Material: 304 Stainless steel; Finish:
Natural; Thread: 11/16-20, 1/2-20;
Thread length: 11/16-20 .394; 1/2-20
.825; OAL: 1.965; ID: .285; Hex: .6875
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
5
Carburetor & Fuel Injection
Co
Cadillac
& LaSalle V-8 Braided Flexible Fuel Hose
$103.00
CAD-0035
Braided bronze Titflex flexible fuel line
hose for connecting the vacuum tank
to the carburetor on 1931 Cadillac &
LaSalle V-8 models 345A and 355A.
Authentic reproduction of the original
Titeflex hose.
Material: Brass & bronze; Finish:
Natural; Thread: 11/16-20; OAL: 18
1/8; Hose length: 16 3/8; End hex: 3/4
and 13/16; End length: 1.00; Hose
OD: 1/2
Co
Cadillac
Johnson Carburetor Manifold Gasket, V12
Co
Cadillac
9/16-18 Fuel Line Flare Nut, V8 V12 V16
$4.25
CAD-0057
9/16-18 Flare nut with flat shoulder for
use on 5/16 fuel line. Cadillac group
number 12.2905, part number 76281.
For use on 1927-1930 Cadillac and
LaSalle V-8, V-12 and V-16 models:
303, 328, 340, 341, 345 A, 353, 355
A, 370 A, 452 A.
Material: Brass; Thread: 9/16-18; OAL:
.980; Hex: 3/4; ID/OD of tapered end:
3/8, 1/2; OD non-tapered end: .731
Must be used with our part MISC-0074.
V16
Co
Cadillac
$8.25
CAD-0078
Intake manifold to carburetor gasket
for 1930-1931 V-12 and V-16 Cadillac,
models 370A and 452A. Cadillac part
number 881304, group number
12.0021.
$5.75
CAD-0056
1/2-20 Oil line flare nut that can be
used with a flat inside shoulder. For
use with a 1/4 or 1/8 line depending
on the ferrule used. Cadillac group
number 12.2905, part number
870294.For use with 1927-1930
Cadillac and LaSalle V-8 and V-16
models: 303, 328, 340, 341, 345 A,
353, 355 A, 452 A.
ID: 1.700; OD: 2.886; Length across:
3.792; Stud holes: large .352, small
.221
Co
Cadillac
Johnson Carburetor Fuel Inlet Nipple, V8
V12
$36.25
CAD-0105
Stainless steel fitting for use in
connecting the carburetor to the fuel
inlet. For use on 1931 Cadillac V12.
Will also fit V8 models. Cadillac part
number 888726, group number
12.0711.
1/2-20 Oil Line Flare Nut, V8 V16
Material: Brass; Thread: 1/2-20; OAL:
.882; Hex: 5/8; ID/OD tapered end:
.314, .481; OD non tapered end: .592
Co
Cadillac
Johnson Carburetor Accelerator Pump
Bleed Screw
Material: 304 Stainless steel; Finish:
Natural; Thread: 9/16-18, 1/2-20;
Thread length: 9/16-18 .394; 1/2-20
.825; OAL: 1.715; ID: .250; Hex: 11/16
x 3/8
$10.50
CAD-0150
CNC Machined stainless steel 10-24
screw for Cadillac Johnson
carburetors. Used as an accelerator
pump bleed screw on carburetors
installed on 1923 - 1925 Cadillac Type
63. May also be for use on later years.
This bleed screw has a precisely
machined "square cornered" head to
fit flush into the carburetor. Cadillac
part number 132507, group number
12.0353, "Screw In Carburetor Body
At Side Of Throttle Pump For Air
Passage".
Material: Stainless steel; Finish:
Natural; Thread: 10-24; Thread length:
1.200; OAL: 1.352; Length under
head: 1.205; Head OD: .312; Head
length: .136
Version 11/20/2014
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
6
Carburetor & Fuel Injection
Co
5/16
45' Flare Ferrule for Fuel, Oil & Vacuum Lines
$5.25
MISC-0074
Brass 5/16 45° flare ferrule. Solders to
5/16 tube, has female 45° flare.
Cadillac part number 877325. For use
with our part CAD-0057. Available in
Brass or Stainless Steel.
Co
Cadillac
1/2-20 Flare Nut for Vacuum Line, V8 V16
$4.25
CAD-0055
1/2-20 Brass flare nut for a 1/4 flared
vacuum line, no ferrule required.
Cadillac group number 8.3420, part
number 73787. For use on 1927-1930
Cadillac and LaSalle V-8 and V-16
models: 303, 314, 328, 340, 341, 345,
353, 355 A B C, 452 A.
Thread: 1/2-20; OAL: 3/4; Hex: 5/8;
ID/OD non threaded end: .265, .445;
OD non tapered part: .620
Co
Cadillac
11/16-20 Fuel Line Flare Nut, V8 V16
Co
Cadillac
Johnson Carburetor Connector for
Throttle Pump Plunger Spring End, V8 V12 V16
$3.75
CAD-0084
Brass connector for joining ends of
accelerator pump plunger spring.
Used on many Cadillacs and LaSalles
from 1920-33. Cadillac group number
12.0285, part number 50694
For use on:
Cadillac V8 1920 - 1933
Cadillac V12 1930 - 1931
Cadillac V16 1930 - 1931
LaSalle V8 1927 - 1933
Material: Brass; Finish: Natural; OAL:
.437; End OD: .125; End length: .197;
Mid OD: .260; Mid length: .043
Co
3/8
45' Flare Ferrule for Fuel, Oil & Vacuum Lines
$5.25
MISC-0076
Brass 3/8 45° flare ferrule. Solders to
3/8 tube, has female 45° flare.
Cadillac part number 877327. For use
with our part CAD-0058.
Material: Brass or Stainless steel;
OAL: .584; ID: .312 at lip, .380 at
body; Body: .482 x .437 OD; Lip: .092
x .500 OD
$5.75
CAD-0058
11/16-20 flare nut with flat inside
shoulder for a 3/8 fuel line. Cadillac
group number 12.2905, part number
875698. For use with 1927-1930
Cadillac and LaSalle V-8 and V-16
models: 303, 328, 340, 341, 345 A,
353, 355 A, 452 A.
Co
Cadillac
Material: Brass; Thread: 11/16-20;
OAL: .950; Hex: 7/8; ID/OD of tapered
end: .452, .589; OD Non tapered end:
.854
V-16 Vacuum Tank Knurled Vent Knob
$10.50
CAD-0162
Knurled knob for the vacuum tank vent
on 1930 - 1931 Cadillac V-16. Sold
with a natural finish - knob is normally
chromed prior to installation on car.
Cadillac part number 882187, group
number 12.3860 "Nut for vacuum tank
top cover".
Must be used with our part MISC-0076.
Material: 12L14; Finish: Natural;
Thread: 1/4-20; Length: .618; OD:
.625; ID: .208; Hole: .09; OD at
bottom: .500
Version 11/20/2014
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
7
Carburetor & Fuel Injection
Co
Cadillac
Vacuum Fuel Pump Gas Shutoff Valve,
V12, V16
$77.25
CAD-0144, CAD-0144-B
Vacuum fuel pump gas shutoff valve
for Cadillac V-12 and V-16. Chrome
plated for corrosion resistance.
Offered in two lengths. Please select
the length(s) that fits your model.
Cadillac part number 882717, group
number 12.3845, "Vent For Vacuum
Tank".
CAD-0144-B, Long style
Material: Brass, steel; Finish: Chrome;
Thread: 3/8-24; OAL: 2.375; Hex:
.437; Shaft OD: .218; Point OD: .275;
Nut length: .375
CAD-0144, Short style
Material: Brass, steel; Finish: Chrome;
Thread: 3/8-24; OAL: 1.531; Hex:
.437; Shaft OD: .218; Point OD: .275;
Nut length: .375
Co
Cadillac
V-16 Titeflex Flexible Fuel Hose (Short)
$103.00
CAD-0081
"Titeflex" flexible bronze braided hose
used to connect the vacuum tank to
the carburetor on 1930 and 1931
Cadillac V-16 452A. This is the
shorter of the two fuel hoses used on
Cadillac V-16. Faithful reproduction of
the original "Titeflex" braided bronze
hose. Cadillac group number 12.2800,
part number 881629.
Material: Bronze;Finish: Natural;
Thread: 11/16-20; OAL: 17 1/2; Hose
length: 15 5/8; Hose OD: 1/2; End hex:
3/4 and 13/16
Co
Cadillac
V-16 Titeflex Flexible Fuel Hose (Long)
$103.00
CAD-0080
"Titeflex" flexible bronze braided hose
used to connect the vacuum tank to
the carburetor on 1930 and 1931
Cadillac V-16 452A. This is the
longer of the two fuel hoses used on
Cadillac V-16. Faithful reproduction of
the original "Titeflex" braided bronze
hose. Cadillac part number 881629.
Co
Schebler
S Carburetor Float, 1 3/4 x 1 1/4
$81.75
SCH-0001
New brass float to fit Schebler brass,
iron and diecast single and duplex
Model S Carburetors.
Float size: 1 3/4 OD x 1 1/4 long.
Co
Schebler
S Carburetor Float, 1 3/4 x 1 15/16
$108.25
J-990-1-A
New brass float to fit Schebler brass,
iron and diecast single and duplex
Model S Carburetors.
Float size: 1 3/4 OD x 1 15/16 long.
Co
Schebler
S Carburetor Retaining Screw
$4.75
J-990-101
Retaining screw for Schebler Model S
single and duplex carburetors.
Schebler part #S-93.
Material: 303 SS; Thread: 10-32;
Thread length: .226; OAL: .717; Head:
.250 Slotted
For use on Model S carburetors
including: SX - 302, 406, 407, 408;
SX - 66A, 77A, 7A; SX - 355, 391
Co
Schebler
S Carburetor Strainer Nut Gasket
$1.75
J-990-27
Strainer nut gasket for Schebler Model
S single and duplex carburetors.
Schebler part #P710.
Material: Vulcanized paper; ID: .877;
OD: 1.160; Thckness: .031
Material: Bronze; Finish: Natural;
Thread: 11/16-20; OAL: 19 1/8; Hose
length: 17 5/8; Hose OD: 1/2; End hex:
3/4 and 13/16
Version 11/20/2014
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
8
Carburetor & Fuel Injection
Co
Schebler
S Carburetor 1 1/2 Needle & Seat
$53.75
J-990-41-A
Schebler Model S carburetor float
valve and brass seat. Valve is made
from brass and has a high strength
Viton rubber tip. Part of the float valve
& seat assembly, Schebler part X2822.
Fits Schebler carburetor models SX:
351, 352, 354, 368, 389, 393, 400,
410, 413, 416, 417, 425, 430, 435,
436, 445, 449, 452, 453, 457 and
other 1 1/2" Schebler carburetors.
Material: 303 SS; Thread: 1/4-32;
Thread Length: .545; Head: 5/16 Hex;
OAL: .840
S Carburetor Choke Wire Clip Screw
$5.25
J-990-70
Choke wire clip screw for Schebler
Model S single and duplex
carburetors. Schebler part #S1614A.
Material: 303 SS; Thread: 1/4-32;
Length: .875
For use on Model S carburetors
including: SX-7A 1 1/2" Brass, SX-348
2 1/2" Brass, SX-383 1 3/4" Kermath,
SX-398A 1 3/4" Brass, SX-404
Co
Schebler
Material: 303 SS; Thread: 1/4-20;
Thread Length: .400; Head: 7/16 Hex;
OAL: .600
For use on Model S carburetors
including: SX-346 2" Brass, SX-348 2
1/2" Brass, SX-383 1 3/4" Kermath,
SX-391 1 3/4" Brass, SX-430 2" Brass
S Carburetor Bowl Retaining Screw
$3.25
J-990-17
Bowl retaining screw for Schebler
Model S single and duplex
carburetors. Schebler part #SM-6.
For use in Schebler S carburetors
including: SX-7A 1 1/2" Brass, SX-432
1 1/4" Duplex, SX-436 1 1/2" Duplex
S Carburetor Idle Adjustment Screw
$7.00
J-990-108
Schebler Model S carburetor idle
adjustment screw with slotted head.
Used to adjust idle balance on duplex
carburetors.
Material: 303 SS; Thread: 1/4-40;
Thread Length: .405; OAL: .405
Co
Schebler
Material: 303 SS; Thread: 1/4-32;
Thread Length: .500; Head: Dia. 405,
Fillister Slotted; OAL: .700
Version 11/20/2014
S Carburetor Range Screw
$5.25
J-990-68
Range adjusting screw for Schebler
Model S single and duplex
carburetors. Schebler part #1183A.
Seat: OAL: 7/8, Hex: 5/8, ID: .205 to
.348, Thread: 1/2-24
Co
Schebler
S Carburetor Dash Lever Tappet Screw
$7.25
J-990-86
Dash lever tappet screw for Schebler
Model S single and duplex
carburetors. Schebler part #S1808.
Co
Schebler
Needle: OAL: 1 1/4, OD: 5/16
Co
Schebler
Co
Schebler
S Carburetor Idle Screw Lock Nut
$5.25
J-990-109
Schebler Model S carburetor idle
adjustment screw lock nut.
Material: 303 SS; Thread: 1/4-40; Hex:
7/16; Thickness: .165
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
9
Carburetor & Fuel Injection
Co
Schebler
S Carburetor Air Bend
$108.25
J-990-13
Air bend for Model S Schebler updraft
carburetors. Perfect bronze
reproduction, cadmium plated.
Measures 2 1/2" x 1 1/2" with open
end threaded to screw on to the
bottom of the carburetor.
Co
Schebler
S Carburetor Bowl
Material: Aluminum; Finish: Natural;
Thread: 7/16-20; Length: 8.125;
Width: 4.078; Height: 4.4156; Wall:
.125; ID at top: .890
S Carburetor Bowl Nut
Material: Brass; Thread into carb: 7/820; Thread for air inlet: 1 1/16-20; Hex:
1 1/8; Length: .851; I.D.: .717
S Carburetor Float Valve Seat Gasket
$1.25
J-990-42
Schebler Model S float valve seat hard
fiber gasket. For use with 1 1/2
carburetors. For use with our part
number J-990-41.
Material: Fiber; OD: .618; ID: 1/2;
Thickness: .030
For use with 1 1/2 carburetors and
Schebler SX models: 351, 352, 354,
368, 389, 393, 400, 410, 413, 416,
417, 425, 430, 435, 436, 445, 449,
452, 453, 457
Version 11/20/2014
$42.25
SCH-0005-A
Carburetor seat and needle with Viton
tip for use in Schebler Model S single
and duplex carburetors. Needle is
made from stainless steel and has a
high strength Viton rubber tip.
Seat
Schebler number S-1661
Fits Schebler carburetor models SX:
184, 186, 192, 196, 218, 222, 227,
230, 232, 237, 241, 242, 249, 252,
265, 266, 267, 274, 291, 295, 299,
300, 301, 302, 315, 319, 334, 340,
341, 359, 374, 380, 388, 401, 407,
408, 41.
Needle
DIA: 1/4; OAL: 1.00
$31.00
J-990-19
Bowl nut for Schebler Model S single
and duplex carburetors. Schebler part
#S1796.
Co
Schebler
S Carburetor Needle & Seat, S-1660 S-
1661
Needle
Schebler number S-1660
$412.00
J-990-16
Cast aluminum carburetor bowl used
on Duesenberg Model J. For use on
Schebler carburetor model SX-368 /
SX-436. Schebler part number SV247A.
Co
Schebler
Co
Schebler
Seat
OAL: 7/8; Hex: 1/2; ID: .261 to .118;
Thread: .404-24
Co
Schebler
S Carburetor Needle & Seat, S-1761 S-
1760A
$51.50
SCH-0003-A
Brass carburetor seat and needle with
Viton tip for Schebler Model S single
and duplex carburetors. Needle is
made from steel and has a high
strength Viton rubber tip.
Schebler needle S-1761.
Schebler seat S-1760A.
Fits Schebler carburetor model SX:
258, 263, 312, 313, 314, 317, 332,
339, 343, 355, 356, 357, 360, 371,
372, 373, 377, 381, 383, 386, 387,
391, 392, 395, 399, 402, 404, 411,
414, 418, 422, 424, 426, 427, 428,
432, 433, 438.
Needle
OAL: 1 1/16; DIA: 17/64
Seat
Hex: 9/16; OAL: 7/8; ID: .176 to .312;
Thread: 7/16-24
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
10
Carburetor & Fuel Injection
Co
Schebler
S Carburetor Strainer Nut
$31.00
J-990-26
Schebler Model S carburetor strainer
nut for single and duplex carburetors.
Schebler part #S1620A.
Material: Brass; OD Thread: 7/8-20; ID
Thread: 1/4 Pipe; Hex: 1 1/16
Co
Schebler
S Carburetor Needle Valve Jet Sleeve
$128.75
SCH-0007
Brass jet sleeve for needle valves as
used on all diecast Schebler Model S
carburetors with adjustable jet tubes.
This sleeve may work with brass
carburetors, but would require
recalibration.
Schebler part number S-1700
Co
Schebler
S Carburetor Bowl Drain Plug
$5.50
J-990-21
Schebler Model S carburetor bowl
drain plug for use in single and duplex
carburetors.
Material: Brass; Thread: 1/8 Pipe;
Hex: 7/16; Length: .585; Finish: Nickel
For use on Model S carburetors
including: SX-7A 1 1/2" Brass, SX-348
2 1/2" Brass, SX-383 1 3/4" Kermath,
SX-398A 1 3/4" Brass, SX-404
Co
Schebler
S Carburetor Air Valve Stem Spring
$29.00
J-990-39
Air valve spring for 1 1/2" duplex
Schebler Model S carburetors as used
on Duesenberg Model J and other
cars of the era. Schebler part number
48-HH.
Material: Spring steel; Free length:
3.32; OD: 1.063; Wire: .042; Top ID:
.344
Specific to models: SX-368, SX-369,
SX-435, SX-436.
Co
Schebler
S Carburetor Main Jet Tube Threading
Tool
$12.75
SCH-0008
Tool for cleaning the threads of
Schebler Model S carburetor jet tubes
that have a 5/16-24 thread.
Material: OH Drill rod; Finish: Natural;
Thread: 5/16-24; OAL: 6.00; DIA: 5/16;
Square end: 15/64 x 15/64 x 5/16;
Thread length: 1.350
Material: Brass; Finish: Natural;
Thread: .278 -24; Thread length: 5/8;
OAL: 2.783; Splines: 22 splines .495 x
5/16; ID: .142 to .281; Shaft OD: 5/16,
.278
Co
Schebler
S Carburetor 1/4-32 Cable Clamp Screw
$18.25
SCH-0010
1/4-32 x 3/8 Steel screw used with the
cable clamp on many Schebler SX
carburetors.
Material: Steel; Finish: Natural;
Thread: 1/4-32; Thread length: .281;
OAL: .620; Hex: .437; Length under
head: .312; Head height: .308; Slot:
.075
Co
Schebler
S Carburetor Air Valve Spring
$31.00
SCH-0009
Air valve spring #48E for use on all 2
1/2" S Series Schebler carburetors.
For use on: SX-257, SX-264, SX-344,
SX-347, SX-348, SX-350, SX-376,SX394, SX-403, SX-405, SX-425, SX431, SX-448, SX-457, SX-459, SX460. Schebler part number 48E.
Material: Spring steel; Coils: 16;
Length: 5 1/4; Wire DIA: .047; OD
(large): 1.05; OD (small): .330
Co
Schebler
S Carburetor 1 1/4 Air Valve Spring
$25.75
SCH-0018
Air valve stem spring used in 1 1/4"
Duplex Schebler carburetors. For use
on carburetors that interchange with
SX-432. Schebler part number 48PP.
Material: Steel; OAL: 2.140; Number
of coils: 7; Wire: .042; OD: 1.092
For use on: Auburn 1928 - 1930; Cord
1929 - 1930; Marmon 1930; Pierce
Arrow 1929; Stutz 1927 - 1928.
Version 11/20/2014
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
11
Carburetor & Fuel Injection
Co
Schebler
L Carburetor Needle & Seat
$59.75
SCH-0013-A
Needle and seat for Schebler Model L
carburetors. For use in both 2" and 2
1/2" bore carburetors as used on
American LaFrance fire engines and
other makes. Includes seat gasket.
Schebler part numbers: Needle S0172; Seat S-1069.
Material: Brass, steel, viton; Finish:
Natural; Thread: 7/16-24; Needle OAL:
.760; Needle width: .269; Seat OAL:
.764; Seat length under head: .537;
Seat thread length: .250; Seat head
OD: .562
Co
Schebler
L Carburetor Float, 2" Bore
$103.00
SCH-0015
Carburetor float for 2" bore Schebler
Model L carburetors as used on
American LaFrance fire engines and
other makes. This float also includes
Schebler part number X-1178-A, float
washer and screw.
Material: Foam; OD: 2.470; ID: 1.512;
Height: .835; Cut out: .472 x .228
Co
Schebler
L Carburetor Float, 2 1/2 Bore
$103.00
SCH-0014
Carburetor float for 2 1/2 bore
Schebler Model L carburetors as used
on American LaFrance fire engines
and other makes using carburetor
assembly LX-355. This float also
includes Schebler part number X-1178A, float washer and screw. Schebler
part number X-38-A
Co
Detroit
Lubricator Model 51 Needle & Seat, 1 1/2
Bore
$50.00
MISC-0155-A
Detroit Lubricator Model 51 carburetor
seat and float valve needle with Viton
tip. For use on the following:
Cadillac
1932-37 V-12 & V-16; 370 B/C/D, 452
B/C/D, 40, 60, 80, 85, 90
Packard
1930 726, 733, 740, 745
1931 826, 833, 840, 845
1932 900, 901, 902, 903, 904
Graham
1930 207, 224, 298, 42-322
1931 49-822, 53, 54, 820,824,STD 6
& 8, Special 6 & 8
1932 49, 58, 820, 834, Blue Streak
1933 57A, 63, 64, Blue Streak
Needle
Material: 303 SS; Top DIA head: 15/32
x .050; Mid DIA head: 23/64 x .160;
Bottom DIA head: 15/32 x .036; Shaft:
1/4 x 1 1/16; Viton length: 3/16
Seat
Material: Brass; Thread: 7/16-20;
Thread length: .208; OD: .556; OAL:
1.240; ID: 1/4 to 1/8; Side holes: .210
Material: Foam; OD: 3.960; ID: 1.980;
Height: .843; Cut out: .475 x .200
Version 11/20/2014
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
12
Carburetor & Fuel Injection
Co
Detroit
Lubricator Model 51 Needle & Seat, 1 1/4
Bore
$50.00
MISC-0218-A
Seat and needle for the float valve
used in Model 51 Detroit Lubricator
carburetors with 1 1/4" bore. Needle is
threaded and adjustable but has been
matched to the proper length for our
seat. The length has been fixed with
Loctite but can be adjusted if
necessary. For use on:
1931, 1933, 1934 Graham Std. 6 and
Spec. 6
Model X8244 carburetor as used on
1934, 1935 Cadillac V8
Needle
Material: Brass, steel, Viton; OAL:
1.350; Brass OD: .468, .359; Brass
length: .328; Steel length with Viton:
1.000; Steel OD: .156
Seat
Material: Brass; Finish: Natural;
Thread: 3/8-24; Thread length: .280;
OAL: 1.222; OD: .500; ID: .164; Side
hole ID: .152; Slot: .090
Co
Stromberg
Co
Stromberg
Carburetor Check Valve Channel Plug
$5.75
STR-0006
Brass slotted plug with 10-32 thread
for the pump check valve channel.
This plug was used on most
Stromberg carburetors from Model O
through the EE series. Stromberg part
number P-7098. Available brass or
nickel plated.
Co
Stromberg
Carburetor Pump Discharge Channel
Plug
$5.75
STR-0005
Brass slotted plug with 5/16-24 thread
for the pump discharge nozzle
channel. This plug was used on most
Stromberg carburetors from Model O
through the EE series. Stromberg part
number P-6406 and P-6402. Available
brass or nickel plated.
Co
Stromberg
Carburetor Idle Channel Plug
5.75
Carburetor Metering Jet Wrench
$36.25
STR-0039
Stromberg carburetor metering jet
wrench. Manufactured from stainless
steel. Fits jets P-19442, P-17004 and
P-22660. For use with the following
series carburetors: AA, AAV, BXO,
BXOV, BXV, EE, WW and many
others.
5.75
STR-0007
Brass slotted plug with 8-32 thread for
the idle channel. This plug was used
on most Stromberg carburetors from
Model O through the EE series.
Available brass or nickel plated.
Wrench end Dia. is 3/8", length of
wrench end is 1", OAL is 2 3/4", end
ID is .217 x .288.
Co
Stromberg
Carburetor French Import Tag
$11.00
TAG-0010
New tag with black background for
installation on Stromberg carburetors
used on French cars such as Bugatti
and others.
Version 11/20/2014
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
13
Carburetor & Fuel Injection
Co
Stromberg
EE-23 Carburetor Needle & Seat
$42.25
STR-0024-A
Stromberg EE-23 carburetor seat and
needle with Viton tip. Needle is made
from stainless steel and has a high
strength Viton rubber tip. Fits
Stromberg EE-23 carburetors as used
many cars of the era including:
Needle
OAL: 11/16; DIA: 7/32; Hole: 1/16
Seat
OAL: 1.00; Hex: 9/16; ID: .242 on
external threaded side; Thread: .43224 external, 1/8-27 NPT internal
EE-3 EE-22 Carburetor Ball Joint
Swivel End
$20.75
P-0149
Ball joint used on Packards from
1932 - 1938 as part of the carburetor
connecting rod assembly used on
Stromberg EE-22 and EE-3
carburetors. Links the automatic
choke to the carburetor. Stromberg
part number P-17761. Used with
Stromberg assembly P-18734 from
1933 - 1934 and P-18397 from 1935 1938.
Material: Steel; Finish: Natural;
Thread: 8-32, 10-32; 10-32 Thread
length: .290; Cylinder: .250 OD x .675;
Hex: .250; OAL: .675; OAW: .750
Co
Stromberg
EE-3 Carburetor Oversize Jet Plug
$16.50
STR-0010
Oversize jet plug to repair carburetor
float bodies with stripped threads.
Stromberg part #P-16978.
$56.75
STR-0075
New leather accelerator pump piston
& shaft for Stromberg EE-22
carburetors. Stromberg part number P17073.
Material: Brass; OAL: 3.00; Top OD:
.660
Co
Stromberg
EE-3 Carburetor Oversize Jet Plug with
Slotted Head
$16.50
STR-0011
Oversize jet plug with slotted head to
repair carburetor float bodies with
stripped threads. Stromberg part # P16978.
Thread:1/2-24; Hex: 5/8 x 11/16 OAL
Co
Stromberg
EE-3 Carburetor Jet Plug
$16.50
STR-0049
Jet plug to repair carburetor float
bodies with stripped threads. This is
the standard sized version of our STR0010. Stromberg part #P-16978.
Thread: 7/16-24; Thread length: .291;
Hex: 5/8 x 11/16 OAL; Head: .196
Co
Stromberg
Thread: 1/2-24; Hex: 5/8 x 11/16 OAL
Version 11/20/2014
EE-22 Carburetor Accelerator Pump
Piston
For use on:
1934-35 Hupmobile O, T
1933-34 Packard 1001, 1002, 1103,
1104, 1105
1932-34 Studebaker 332
1936 Buick 60, 80, 90
1934-37 Chrysler CU, CV, C-2, C-3, C10, C-11, C-17
1933-35 Lincoln V12
Hupmobile 6-A & 8-M
1935 Packard 1200, 1201, 1202,
1203, 1204, 1205
1936 Packard 1400, 1401, 1402,
1403, 1404, 1405
1937 Packard Super 8, 1500, 1501,
1502
Co
Stromberg
Co
Stromberg
EE-3 Carburetor Accelerator Pump
$56.75
STR-0019
New leather accelerator pump, piston
and shaft for Stromberg EE-3
carburetors. Stromberg part #P17448.
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
14
Carburetor & Fuel Injection
Co
Stromberg
EE-3 UU-3 Carburetor Needle & Seat
$41.25
STR-0017-A
Stromberg EE-3 carburetor seat and
needle with Viton tip. Needle is made
from steel and has a high strength
Viton rubber tip. This needle and seat
will also fit UU-3 carburetors as used
in Duesenberg and Hupmobile Model
C. Stromberg part number P-18915.
Fits Stromberg EE-3 carburetors used
in many cars including:
Chrysler
Duesenberg
Hupmobile
Packard
Pierce Arrow
Stutz
Co
Stromberg
EE-3 Carburetor Air Horn Gasket
$12.50
STR-0020
Stromberg EE-3 carburetor air horn
gasket made from durable gasket
material.
Co
Stromberg
EE-3 Carburetor Main Body Gasket
$5.25
STR-0021
Stromberg EE-3 carburetor main body
gasket made from durable gasket
material. Stromberg part number P17393.
Needle
OAL: 1.00; DIA: 1/4 square
Seat
OAL: 1 1/32; Hex: 1/2; OD: 7/16; ID:
.332 to 1.36; Thread: 3/8-24
Co
Stromberg
Co
Stromberg
EE-3 Carburetor Accelerator Pump
Lever Cover
$77.25
STR-0058
Steel cover for the accelerator pump
lever for Stromberg EE-3 carburetors.
Stromberg part number P-17397A.
For use on:
1934-35 Chrysler CW
1934-37 Duesenberg J, SJ
1930-31 Hupmobile C and 1931 H, U
1932 Packard 905, 906
1933 Packard 1005, 1006, Twelve
1934 Packard 1107, 1108
1935 Packard 1207, 1208
1936 Packard 1407, 1408
1937 Packard 1506, 1507, 1508,
Twelve
1933 Pierce Arrow 836, 839; 1934
836, 840; 1935 845; 1936 1601; 1937
8, 1701
1934-37 Stutz DV 32
EE-3 Carburetor Accelerator Pump Link
$36.25
STR-0027
Stromberg EE-3 carburetor
accelerator pump link.
Link measures: 5.030 OAL, round end
is .477 OD, rod is .152 DIA.
For use with Stromberg EE-3
carburetors as installed many cars of
the 1930's including: 1934 Chrysler
CL & CW; Duesenberg Model J; 1932
Packard Twin Six; 1933 Pierce Arrow
836 and 839; 1934 Pierce Arrow 135,
238 and 234; 1932-33 Stutz DV-32
Material: Steel; Finish: Painted;
Length: 2.500; Width: 2.000; Height:
.570; Thickness: .035; Oval hole: .192
x .285
Version 11/20/2014
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
15
Carburetor & Fuel Injection
Co
Stromberg
EE-3 Carburetor Needle to Float Clip
$10.50
STR-0073
Stainless steel clip used in Stromberg
EE-3 carburetors to secure the float
needle to the float. Also referred to as
a "float hanger". Stromberg part
number P-17473. For use in
Stromberg EE3 carburetors as used
on:
1934-35 Chrysler CW
1934-37 Duesenberg J, SJ
1930 Hupmobile C; 1931 H, U
1932-1937 Packard Twelve
1933 Pierce Arrow 836, 839; 1934-36
385, 836A, 840A, 845, 1601; 1937-38
385, 838, 844, 847
1933-34 Stutz DV-32; 1934-35 SV-32
Material: Stainless steel; Finish:
Natural; Length x width OD: .500 x
.250; Length x width ID: .412 x .162;
Wire: .040
Co
Stromberg
Co
Stromberg
Measures: 5/8 OD, 9/16 ID, has 3/8
hole for #4 machine screw.
Fits Stromberg EE-3 carburetors as
used in many cars including:
Chrysler: 1933 CH & CL
Chrysler: 1934 CW
Packard: 1935 - 36, 1207-8 &1407-8
Packard 12, 1932-33
Packard: 1937-38, 1506-8 & 1606-8
Pierce Arrow: 1933 836 & 839
Pierce Arrow: 1934 - 35 836-A, 840-A,
845 & 1601
Pierce Arrow: 1937 438, 444, 447
Co
Stromberg
EE-3 Carburetor Air Horn Screw
$15.50
STR-0004
Stainless steel 1/4-20 x 2 9/16 fillister
head air horn attaching screw for
Stromberg EE-3 carburetors. May also
be compatible with other Stromberg
models. Stromberg part number P18111.
EE-3 Carburetor Acorn Nut
$13.00
STR-0012
Stainless steel acorn nut with 10-24
thread. Used to hold the air horn to the
main body on Packard, Duesenberg
and other cars using Stromberg air
horn #P-18155 & #P-17759.
Stromberg part number P-17774-L.
Screw has 10-32 thread, 1 11/16 OAL
and 1/8 Dia. shank.
EE-3 Carburetor Bowl Vent Adapter
$9.50
STR-0009
Stromberg EE-3 carburetor bowl vent
adaptor.
EE-3 Carburetor Upper Cover Stud
$6.75
STR-0014
Cadmium plated air horn retaining
stud for Stromberg EE-3 carburetors
as used on Packard, Duesenberg and
others. Stud has 10-24 thread on each
end, 3 1/2 OAL. Stromberg part
number P-17773.
Co
Stromberg
Co
Stromberg
EE-3 Carburetor Float Screw
$18.50
STR-0013
Brass float fulcrum screw for
Stromberg EE-3 carburetors. Available
plain brass or nickel plated. Stromberg
part number P-17446.
Co
Stromberg
Co
Stromberg
EE-3 Carburetor Breather Cover
$19.50
STR-0032
Stromberg EE-3 carburetor breather
cover. Made from stainless steel.
EE-3 Carburetor ID Tag
$46.50
STR-0003
New tag with black background and
raised letters. For use on Stromberg
EE-3 carburetors.
Measures 1 1/2 x 5/8.
Made from brass with 5/16-24 thread,
measures .375 x .591.
Version 11/20/2014
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
16
Carburetor & Fuel Injection
Co
Stromberg
EE-3 EE-22 EE-23 Carburetor
Accelerator Pump Check Valve
$36.25
STR-0074
Accelerator fuel pump inlet check
valve for Stromberg EE-3 carburetors
as used on Packard V-12 and others.
Also used in EE-22 and EE-23
Stromberg carburetor assemblies.
Stromberg part number P-16990,
"Check valve for pump inlet".
Material: Brass, copper, micarta;
Finish: Natural; Thread: 7/16-24;
Thread length: .125; OAL: .531; Hex:
.468; ID: .142
Co
Stromberg
UU-2 DD-3 Carburetor Needle & Seat
$53.75
STR-0031-A
Stromberg UU-2 & DD-3 carburetor
seat and needle with Viton tip.
Seat
OAL: 1 3/8; Hex: 1/2; Thread: 5/16-24
UU-2 Carburetor Small Gasket Set
$43.50
STR-0060
Set of cork and fiber washers as used
on Stromberg UU-2 carburetors.
UU-2 Carburetor Main Body Gasket
$12.50
STR-0038
Stromberg UU-2 carburetor main body
gasket made from gasket paper.
Measures: approx 4.440 x 6 x .025.
Fits Stromberg UU-2 carburetors as
used many cars including:
1928 - 1929 Auburn 8-88, 8-90, 115,
120-125
1930 Cord
Continental 12-K, 15-S
1920 - 1930 Elcar 130-140
1930 Hupmobile C, C RHD, L, L RHD
1928 - 1929 Hupp Car Century RHD
and others
1929 Kissel 8-95, 126
1929 - 1931 Mack BC, 2BK
Co
Stromberg
Needle
OAL: 1 3/32; DIA: 9/32
Co
Stromberg
Co
Stromberg
UU-2 Carburetor Flange Gasket
$12.50
STR-0035
Stromberg UU-2 carburetor flange
gasket made from gasket paper.
Measures: approx. 3.8 x 2.47 x .027,
stud holes are 3/8 and port holes are
1.465.
Used on many cars including:
1928 - 1929 Auburn 8-88, 8-90, 115,
120-125
1930 Cord
Continental 12-K, 15-S
1920 - 1930 Elcar 130-140
1930 Hupmobile C, C RHD, L, L RHD
1928 - 1929 Hupp Car Century RHD
and others
1929 Kissel 8-95, 126
1929 - 1931 Mack BC, 2BK
Co
Stromberg
UUR-2 Carburetor Needle & Seat
$53.75
STR-0029-A
Stromberg UUR-2 carburetor seat and
needle with Viton tip.
Needle
OAL: 1 3/32; DIA: 9/32
Seat
OAL: 1 9/16; Hex: 1/2; Thread: 3/8-24
Version 11/20/2014
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
17
Carburetor & Fuel Injection
Co
Stromberg
UUR-2 Carburetor Main Body Gasket
$15.50
STR-0028
Main body gasket for Stromberg UUR2 carburetors. Stromberg part number
P-16370.
Auburn 1928-29 120, 125
Auburn 1928-30 8-88, 8-90, 8-95
Black Hawk 1929-30 L8
Cord 1930-32
Cunningham 1932 Continental 12-K
Engine
Gardner 1929-31 130, 140, 148, 150,
158
Hupmobile 1932-33 I, F, F-2
Jordan 1928 JE, G
Locomobile 1928-29 70
Marmon 1930-31 Big 8, H, 88
Marmon 1931 H, CC
Nash 1933-34
Peerless 1930-31 Standard 8, Custom
8, Master 8
REO 1931-32 Royale 8
Stutz 1926-28 AA, AB
Material: Gasket paper; Irregular
shape: approx. 4 1/2 x 8
Used on many cars including:
Auburn 1928-29 120, 125
Auburn 1928-30 8-88, 8-90, 8-95
Black Hawk 1929-30 L8
Cord 1930-32
Cunningham 1932 Continental 12-K
Engine
Gardner 1929-31 130, 140, 148, 150,
158
Hupmobile 1932-33 I, F, F-2
Jordan 1928 JE, G
Locomobile 1928-29 70
Marmon 1930-31 Big 8, H, 88
Marmon 1931 H, CC
Nash 1933-34
Peerless 1930-31 Standard 8, Custom
8, Master 8
REO 1931-32 Royale 8
Stutz 1926-28 AA, AB
Co
Stromberg
UUR-2 Carburetor Small Gasket Set
$43.50
STR-0045
Set of cork and fiber washers for
Stromberg UUR-2 carburetors.
UUR-2 Carburetor Air Horn Gasket
$12.50
STR-0034
Stromberg UUR-2 carburetor air horn
gasket made from gasket paper.
Measures: approx. 3 7/8 x 4 x .025,
stud holes are .200, ID is approx
3.325 x 3.570.
For use on many cars of the 1920's
and 1930's including:
Co
Stromberg
Co
Stromberg
UUR-2 Carburetor Tag
$46.50
STR-0008
New tag with black background and
raised letters. For use on Stromberg
UUR-2 carburetors.
Co
Stromberg
URO-2 Carburetor Throttle Plate
$41.25
STR-0053
Stromberg carburetor throttle valve
used on many models of Stromberg
carburetors:
EC-2; EX-22, 23, 32; EXV-2, 25, 35;
OE-1, 2, 3; OT-2, 3, 4; OX-2; T-2; TX2; U-1, 2, 3; UR-2, 23; URO-1, 2; UUR2; UX-2, 3
Stromberg part number P-6454.
Material: Brass; Finish: Natural; DIA:
1.555 (oblong); Holes: 3/16; Hole
centers: .800; Thickness: .065
Version 11/20/2014
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
18
Carburetor & Fuel Injection
Co
Stromberg
URO-2 Carburetor Throttle Shaft
$46.50
STR-0054
Throttle shaft for Stromberg URO-2
carburetors. For use on:
DD-3 Carburetor Auxiliary Metering Jet
$6.75
STR-0071
0.050 Auxiliary metering jet for
Stromberg DD-3 carburetors. May also
fit other models of Stromberg
carburetors. Stromberg used different
sized auxiliary metering jets
throughout its DD carburetor line. This
jet can be drilled out if larger size is
needed. Stromberg part number P16362. For use on DD-3 carburetors
as installed on:
Auburn
1932 8-100, 1933 8-101
Franklin
1933 18 Olympic, 1934 18 B and C,
1934 19 A and B
Graham
1934 and 1935 Standard 67 Material:
Brass
Finish: Natural; DIA: 1/4; OAL: 5.446;
Slots: 2.080 x .068; 1 3/4, 1.675 from
ends; Holes: 1/4, 3/4 center to center
Co
Stromberg
Co
Stromberg
Carburetor O & M Series Float Cover
1931 Chrysler CG; 1932 CH, CL
1931-32 Lincoln V8; 1932-33 V12
1930-33 Hupmobile 366 H, U
Material: Brass; Finish: Natural;
Thread: 10-24; OAL: .342; Length
under head: .160; Head OD: .250
Nut
Co
Stromberg
$18.25
STR-0052
Float needle valve cap used on many
Stromberg carburetor models, such
as: O-1, O-2, O-3, OE-1, OE-2, OE-3,
OX-2, M-3/4, M-1, M-2 and M-3
Stromberg part number P-16241.
$20.75
STR-0066
Laser cut main body gasket for
Stromberg DD-3 carburetors.
Stromberg part number P-14632.
Material: Brass; Thread: 7/16-24; Hex:
1/2; Hex height: 7/16; OAL: .825; OD:
.460; Hole: .075
Co
Stromberg
DD-3 & DDR-3 Carburetor #70 Air Bleed
$13.00
STR-0062
#70 Brass air bleed for Stromberg DD3 and DDR-3 carburetors. Some DD-3
and DDR-3 models used a #60 or #68
air bleed, such as 1930-32 Chrysler
and 1932 Lincoln 12. Please contact
us for the availability of other air
bleeds. Stromberg part number P14334
For use on the following automobiles
and others:
1931-32 Lincoln 8
1931 Marmon DD
1930-33 Hupp H, U
DD-3 Carburetor Main Body Gasket
Material: Gasket paper; Length: 5.75;
Width: 5.625; Thickness: .028
Co
Stromberg
DD-3 Carburetor Main Discharge Jet
Plug
$6.25
STR-0070
Brass plug for Stromberg DD-3
carburetor idle feed channel plug and
main discharge jet plug. Stromberg
part number P-6207. For use on DD-3
carburetors as installed on:
1931 Chrysler CG; 1932 CH, CL
1931-32 Lincoln V8; 1932-33 V12
1930-33 Hupmobile 366 H, U
Material: Brass; Finish: Natural;
Thread: 1/4-20; OAL: .230; Head DIA:
.250
Material: Brass; Finish: Natural;
Thread: 6-32; Thread length: .130;
OAL: .750; OD: .125; ID at thread:
.060; ID at other end: .028
Version 11/20/2014
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
19
Carburetor & Fuel Injection
Co
Stromberg
DD-3 Carburetor Idle Discharge Hole
Plug
$5.75
STR-0069
Brass plug for Stromberg DD-3
carburetor idle discharge hole plug
and the economizer gas channel plug.
Stromberg part number P-6406. For
use on DD-3 carburetors as installed
on:
1931 Chrysler CG; 1932 CH, CL
1931-32 Lincoln V8; 1932-33 V12
1930-33 Hupmobile 366 H, U
Co
Stromberg
DDR URO UR UUR Carburetor Vacuum
Economizer Plug
$22.25
STR-0055-4
Brass plug part of the vacuum
economizer used in multiple models of
Stromberg carburetors: DXR-2, DDR3, URO-2, UR-2, UR-23 and UUR-2.
For use in many automobiles
produced from 1928 - 1935. Part of
Stromberg P-15479, vacuum
economizer pump.
Material: Brass; Finish: Natural;
Thread: 7/16-24; Thread length: .162;
OAL: .353; Length under head: .250;
OD head: .4375; ID: .135
DD-3 Carburetor Main Gas Channel
Plug
$5.25
STR-0068
Brass plug for Stromberg DD-3
carburetor. For use in gas channel
and pump discharge nozzle channel.
Stromberg part number P-12790. For
use on DD-3 carburetors as installed
on:
DDR-3 Carburetor Pump Lever Spring
$41.25
STR-0082
Pump lever spring for Stromberg DDR3 carburetors as used on 1931 - 1933
Marmon and Duesenberg Model J.
Stromberg part number P-15392.
Material: Spring steel; Length: 1.484;
Width: .968; Thickness: .030; Width of
steel: .250
Co
Stromberg
Material: Brass; Finish: Natural;
Thread: 10-24; OAL: .210; Head DIA:
.187
Co
Stromberg
Co
Stromberg
DDR-3 Carburetor Throttle Shaft
$62.00
STR-0072
Throttle shaft for Stromberg DDR-3
carburetors. Two per carburetor used
in Stromberg assembly numbers P16102 and P-16103, "Left Throttle
Gear and Stem". For use on DDR-3
carburetors as installed on:
1931-33 Marmon
1932 Duesenberg
Material: Brass; Finish: Natural;
Thread: 4-40; OAL: 4.260; OD: .313;
Slot: 2.100 x .072; Holes: .142; Hole
centers: .750
Co
Stromberg
DDR-3 Carburetor Main Body Gasket
$20.75
STR-0064
Laser cut main body gasket for
Stromberg DDR-3 carburetors.
Stromberg part number P-16100.
For use on:
1932 Duesenberg
1931-33 Marmon
Material: Gasket paper; Length: 5.703;
Width: 5.750; Thickness: .025
1931 Chrysler CG; 1932 CH, CL
1931-32 Lincoln V8; 1932-33 V12
1930-33 Hupmobile 366 H, U
Material: Brass; Finish: Natural;
Thread: 8-32; OAL: .187; Head DIA:
.187
Version 11/20/2014
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
20
Carburetor & Fuel Injection
Co
Stromberg
DDR-3 EE-3 Carburetor Intake Manifold
Co
Stromberg
DDR-3 EE-3 Carburetor Intake Manifold
Insulator
Gasket
$77.25
STR-0065, STR-0077
Insulator block used between the
carburetor and intake manifold on cars
requiring a spacer. Fits Stromberg
DDR-3 and EE-3 carburetors with four
mounting holes. Available in two
thicknesses: 1/4 (STR-0077) or 1/2
inch (STR-0065). For use on DDR-3
carburetors as installed on:
$10.50
STR-0076
Gasket used with the insulator block
between carburetor and intake
manifold. Fits DDR-3 and EE-3
carburetors with four mounting holes.
1931-33 Marmon
1932 Duesenberg (Duesenberg part
number J-906)
Material: Gasket paper; Length: 4.875;
Width: 3.175; Thickness: .025; Center
ID: 1.718; Stud holes: .390
Material: Garolite; Finish: Natural;
Length: 4.875; Width: 3.175;
Thickness: 1/2 Inch OR 1/4 inch
Co
Stromberg
Co
Stromberg
DD-3 EE-3 Carburetor Intake Manifold
Insulator
$77.25
STR-0067, STR-0079
Insulator block used between
carburetor and intake manifold on cars
requiring use of a spacer. Fits DD-3
and EE-3 carburetors with 6 mounting
holes. Available in two thicknesses:
1/4 (STR-0079) or 1/2 inch (STR0067). For use on DD-3 carburetors
as installed on:
1930-33 Hupmobile 366 H, U
1931 Chrysler CG; 1932 CH, CL
1931 Lincoln V8; 1932 V8, V12; 1933
V12-145
Material: Garolite; Finish: Natural;
Length: 4.875; Width: 3.175;
Thickness: 1/2 inch or 1/4 inch
Co
Stromberg
DD-3 EE-3 Carburetor Intake Manifold
Gasket
EE-15 Carburetor Throttle Shaft
$92.75
STR-0081
Throttle shaft for Stromberg EE-15
carburetors as used on Cord 810 from
1936 - 1937. May also be compatible
with EE-1, EE-14 and EE-16
carburetors.
Material: Brass; OAL: 4.410; Flat:
1.250; Slot width: .080; Slot length:
2.908; OD: .280; Holes: .142
Co
Packard
Super 8 Choke to Carburetor Connecting
Rod
$46.50
P-0151
Steel connecting rod linking the
automatic choke and carburetor on
1933 - 1934 Packard Super 8
equipped with Stromberg EE-22
carburetor. Used in conjunction with
ball joint, our part number P-0151.
Stromberg part number P-18734.
Packard part number 210195.
Material: Steel; Finish: Natural;
Thread: 8-32; Thread length: .656;
OAL: 8.750; Rod OD: .156; OD at
disc: .487; Disc slot: .095 x .250
$10.50
STR-0078
Gasket used with the insulator block
between carburetor and intake
manifold. Fits DD-3 and EE-3
carburetors with six mounting holes.
Co
Arnott
For use on DD-3 carburetors as
installed on:
1930-33 Hupmobile 366 H, U
1931 Chrysler CG; 1932 CH, CL
1931 Lincoln V8; 1932 V8, V12; 1933
V12-145
Material: Gasket paper; Length: 4.875;
Width: 3.175; Thickness: .025; Center
ID: 1.718; Stud holes: .390
Version 11/20/2014
For use on DDR-3 carburetors as
installed on:
1931-33 Marmon
1932 Duesenberg
Carburettor & Supercharger Tag
$24.75
TAG-0036
Arnott Carburettor tag as used on
Arnott carburetors and superchargers
of the 1950's. Reproduced from a tag
on a 1952 Arnott carburetor.
Material: Aluminum; Length: 2.566;
Width: .900; Thickness: .020
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
21
Carburetor & Fuel Injection
Co
Packard
Carburetor Float Chamber Cap
$20.75
P-0187
Brass float chamber needle valve cap
for Packard carburetors. For use on
1927 - 1929 Packard Eight. Packard
part number 142906.
Material: Brass; Finish: Natural; OAL:
.815; OD: .406; Hex: .4375; ID: .275;
Depth: .656
Co
Packard
Carburetor Float
$103.00
P-0117
Urethane float with brass rubbing
surface for 6 and 8 cylinder Packards
using Packard carburetors. Packard
part number 114751. Fits all 6 cylinder
Packards including Models: 126, 133,
226 ,233, 326, 333, 426, 433, 526,
533. Fits 8 cylinder models 626 and
633.
Material: Urethane & brass; OD: 2 1/8;
ID: .192; Height: 1 1/2
Co
1910-17
Packard Carburetor Venturi
$437.75
P-0189
CNC Machined aluminum venturi
nozzle for Packard carburetors. Used
on carburetors with carburetor body P5190 and may fit 1910 - 1917
carburetors.
Material: Aluminum; OAL: 2.660; ID of
ends: 1.515, 1.00; Wall: .048; ID
center: .730; OD large end: 1.734
Co
Marvel
V-10-733 Carburetor Float
$49.00
MISC-0173
Marvel carburetor float for use on
1929 - 1930 Essex Model 6. This
urethane float has been sealed and
will not absorb gasoline or warp.
Marvel part number 30-519;
carburetors 10-722 VE, 10-778 VE.
Royce Phantom I Carburetor Float Chamber
Cover
$334.75
RR-0006
CNC machined aluminum carburetor
float chamber cover for Springfield
Rolls Royce Phantom I. For use on 4050 HP chassis, Series V, W, X. Rolls
Royce part number 74277.
Material: Aluminum; Finish: Natural;
Thread: 2.670-16, 7/16-18; Outer
thread length: .265; Inner thread
length: .400; OD: 2.952; Height: 1.062;
Hex: .920 x .305; Bottom tabs: .437 x
.656
Co
Rolls
Royce Phantom I Carburetor Inlet Nut
$18.75
RR-0040
Stainless steel hex nut used on Rolls
Royce Phantom I carburetor inlets.
Material: 303 Stainless steel; Thread:
7/16-18; Hex: .6875; OAL: .488; Hex
height: .200; OD: .600; Round height:
.288; Depth: .390
Co
Rolls
Royce Phantom I Carburetor Float Bowl
Cover Cap Screw
$13.00
RR-0042
Hex head cap screw used on Rolls
Royce Phantom I carburetor float bowl
cover.
Material: Brass; Thread: 7/16-18;
Thread length: .343; Length under
head: .387; Hex: .6875; OAL: .553; ID:
.234; Depth: .375
Co
Rolls
Royce Phantom I Carburetor Inlet Banjo
Fitting
$25.75
RR-0041
Banjo fitting for the carburetor inlet on
Rolls Royce Phantom I.
Material: Urethane; Finish: Epoxy
sealed; OD: 1 3/4; Flat: 1.045; Height:
.614; Hole ID: 3/16
Version 11/20/2014
Co
Rolls
Material: 4140 Steel, heat treat grade
8; Finish: Natural; Thread: 7/16-18;
Thread length: .406, .390 (holes end);
OAL: 1.383; Hex: .6875; ID: .250;
Holes: .125
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
22
Carburetor & Fuel Injection
Co
Rolls
Royce Phantom II Carburetor Float Chamber
Cover
$396.75
RR-0007
CNC machined aluminum float
chamber cover for Rolls Royce
Phantom II.
Material: Aluminum; Finish: Natural;
Thread: 2.670-16, 7/16-18; OD: 3.065;
Height: 1.100; Top OD, height: .845 x
.312; Bottom tabs: .375 x .625; Teeth
count: 72
Co
Solex
140 Jet
$9.50
MISC-0275
Brass 140 Solex jet with an M6 x 1.00
thread as used in Mercedes Benz 300
SL mechanical fuel injection. Used as
an idle jet and partial load jet for the
throttle body. May be further drilled out
to meet application demands.
Material: Brass; Finish: Natural;
Thread: M6 x 1.00; Thread length:
.160; Head OD: .300; OAL: .312;
Length under head: .196; ID: .055;
Slot: .062
Co
Alfa
Romeo 3000CM Carburetor Spacer
$103.00
MISC-0280
Laser cut, CNC machined carburetor
spacer for use on Alfa Romeo 3000
CM.
Material: Steel, rubber; Length: 3.734;
Width: 2.500; Height: 1.020; Steel
thickness: .115; Rubber thickness:
.790; ID: 1.875; Centers: 2.973
Version 11/20/2014
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
23