1. home and garden
2. home improvement and repair
3. plumbing

ACO DRAIN
Technical Handbook and Product Catalog
Technical Section
Design assistance & information
Surface Drainage
6
8
10
16
22
24
ACO Drain offer a comprehensice
128 page catalog covering
everything you need to know about
about trench drainage and the
products and services available.
Surface drainage options
Product selection
Trench drain hydraulics
Loadings
Material data
End user requirements
Standard Products
26
40
52
54
56
70
To ease electronic transmission of
data the catalog has been divided
into sections - for a hard copy or
other sections call (800) 543-4764
or go to www.acousa.com.
KlassikDrain - K100S, KS100S
PowerDrain - S100K, S300K
Polymer concrete catch basins
Accessories
FlowDrain - FG100, FG200
FastForm - FF300, FF600
Problem Solving Products
78
84
SlabDrain - H80, H100, H80K, H100K, H100SK
ChemDrain - C100, CK100S, CS100K, CH80, CH100, CH80K, CH100K,
100
102
104
Brickslot
Membrane Drain
MiniKlassik
106
Cross Sidewalk Drain (CSD)
CH100SK
Technical Support and Other Information
110
111
112
114
115
116
120
122
Trench hydraulics service
Grate hydraulics service
Layout & scheduling service
Ponding analysis
Chemical resistance
Construction and installation
Installation diagrams
Volumetric channel capacities
123
Glossary & part number listing
This PDF relates to this
section only
PDF PAGE ONLY
Technical Support
Complimentary services to aid selection, design and installation
ACO has an established Technical Services
Department with many years experience
advising on surface drainage. This free
service is offered with no obligation and
is supported with extensive, high quality
information, brochures and technical
documentation.
Trench hydraulics
SERVICE
1
2
Grate performance hydraulics
SERVICE
Run layout & scheduling
SERVICE
Ponding analysis
SERVICE
4
Materials
SERVICE
5
3
108
www.acousa.com
ACO DRAIN
ACO’s Technical Services Department will
provide assistance in the design of the most
hydraulically efficient and cost effective
drainage layout. Using ‘Hydro’, a purpose
written computer software program, ACO
will provide solutions with all rainfall and
catchment design variables considered.
ACO can supply:
• Hydraulic plots and calculations for
individual trench runs
Page 110
ACO’s ‘GIC’ (Grate Intake Calculator)
computer software program is based on
calculations and empirical data derived from
full scale experimentation. The ‘GIC’ plot
provides information on grate performance
relative to project catchment contours.
ACO can supply:
• Project specific grate performance plot
Page 111
For large catchment areas where complex
surface drainage layouts are required,
ACO can recommend a trench drain
solution to satisfy project cost and design
requirements. Run layouts can be designed
to take full advantage of the existing and
proposed site grades and utilize existing
services where possible.
Temporary ponding can be tolerated during
an intense storm in applications where the
impact is low, e.g., away from buildings,
parking lots, etc. An assessment is made of
the behavior of the ponding pattern when a
smaller, more economical, trench is used.
ACO can supply:
• Plan layouts of trench runs (AutoCAD)
• Section layouts of trench runs showing
modular sequence of channel units
• Parts schedules fully itemizing parts
and pieces
Page 112
ACO can supply:
• Map of temporary ponding
• Approximate duration of any temporary
ponding
Page 114
There are a variety of materials available
for trench drain systems. Each material
behaves differently in various environments
and situations. Following extensive testing,
ACO can provide advice on chemical and
corrosion resistance for most common
trench drain materials.
ACO can supply:
• Material coupons for on site testing
Page 115
www.acousa.com
www.acousa.com
109
Technical Support
1. Trench hydraulic service
‘Hydro’ is a purpose written, hydraulic design
program modeled on differential calculus
for non-uniform flow in open channels,
(See page 10). The program was created
from empirical data, following a series of
experiments modeling lateral intake into
trenches. Analysis of the effect of slope, run
length, and trench cross sectional profiles
were incorporated into the program.
To generate results from the ‘Hydro’ program, the following information is required:
•
•
•
•
•
•
•
•
Complex scenarios such as the effects of
water inflow from down spouts or inlets
along the length of the trench can also be
modeled by the ‘Hydro’ program. ACO can
use ‘Hydro’ to recommend optimum outlet
positions along trench runs.
Length of trench run (feet or meters)
Length and width of catchment area (feet or meters) - see page 12
Surrounding pavement/surface type, e.g., concrete, asphalt, etc.
Rainfall intensity (in/hr or mm/hr)
Ground fall along trench (%)
Perpendicular approach slopes to trench (%)
Preferred position of outlets along trench and any outlet size restrictions
Any slab depth restrictions
Results are provided either electronically and/or in printout format, in metric or imperial units.
‘Hydro’ plot shows:
1 Position and size of minimum ‘freeboard’
(gap between underside of grate and
top of liquid in trench)
( Based o n t he
d iffer ent ial eq u
at io n fo r st ead
y, no n- unif
3 Flow velocity
2 The hydraulic
o r m , fl o w in o p
en channels)
1
363
135
377
158
0
391
177
100
405
193
200
300
418
208
22 m
1%
432
220
utilization of
trench (%)
is given. If
over 100%
flooding occurs.
(47.68% from
example below)
New parking
lot
ACO Polymer
Products, In
c
12080 Ravenn
a Road, Char
don, OH 4402
72’
4
106-001H
446
231
460
238
400
474
238
2
(mm)
5 Hydraulic
discharge
capacity of the
channel run.
(1,395 GPM
- 88 l/s from
example below)
Project:
Client:
Address:
Run:
DS#:
110
C le ar H eig h t
(m
Flow Depth (m m) 350
m) 106
4 Maximum
and flow rate at
all points along
the trench
profile of the
liquid
488
156
0
100
200
300
400
(m/s)
2.5
(l/s)
100
2
80
1.5
60
1
40
0.5
20
0
0
(mm)
(l/s)
100
80
3
0
L iq uid :
K in em at ic visc
o sit y ( cm 2 / s) :
A C O D RA IN ®
Sys
Ro u gh n ess co e t em :
f f ici e n t :
O u t l e t t y p e:
2
Wat er
0 .0 1
S3 0 0 K
95
4
6
40
8
10
12
14
20
16
18
20
Flo w velo cit y (
m / s)
O ut flo w ( l/ s)
4
D isch ar ge (
M in im u m f r eeb lit r es/ sec) : 8 8 .0 0
o ar d
C h an n el cap ac ( m m ) : 2 1 0 .6 8 , X = 1 0 .7 0
it y ( % ): 4 7 .6
m
8
60
Ver t ical scale
H o r izo nt al sca 1:
le 1 :
5
T h e calculat io n
assu m es t h at fl
o w w it hi n t he
r est r ict ed b y o
ch an nel is no t
u t let . 1 0 0 % ca
p acit y r elat es t
t he un d er sid e
o w at er t o uchi
o f t he gr at in g a
ng
t an y p o int alo n
g t h e r u n.
www.acousa.com
Plo t n um b er :
106-001H
ACO Polymer Prod
12080 Ravenna ucts, Inc.
Road, P.O. Box 245
Chardon, Ohio 440
Tel: (440) 285-700 24
Fax: (440) 285-8510
7
0
22 m
Datum
ACO DRAIN
2. Grate Hydraulics
ACO has independently measured, by
experimentation, the hydraulic intake
capacities of ACO Drain grates. Tests were
carried out under varying flow rates and
catchment approach slopes. To determine
the hydraulic utilization, each grate was
tested until bypass occurred (point at which
liquids would pass across grate).
To generate results from the ‘GIC’ program the following information is required:
•
•
•
•
•
•
•
The Grating Intake Calculator (GIC) provides
information on the intake efficiency of the
chosen grate. If the required liquid intake
is greater than the grate’s performance,
the extent of bypass (or failure) will be
calculated. See page 15.
Length of trench run (feet or meters)
Length and width of catchment area (feet or meters) - see page 12
Position of trench in catchment area
Surrounding pavement/surface type, e.g., concrete, asphalt, etc.
Rainfall intensity (in/hr or mm/hr)
Perpendicular approach slopes to trench (%)
Preferred grate type
Results are provided either electronically and/or in printout format.
‘GIC’ plot shows:
geometry and
hydraulics
3 Additional notes
2 Head of water
relating to grate
performance
approaching
grate
on
ke Calculati
Grating Inatladata from experimentation
4 Recommended
6 Hydraulic
area per foot of
trench run
utilization of
grate (100%
means all grate
intake capacity
is used)
0
(440) 285-700
Tel:
5
(440) 285-700 m
Fax:
co
info@acousa.
Email:
lot
New parking
PROJECT:
Contact:
ducts, Inc
O Polymer Pro
Company: AC
piric
Based on em
will discharge
ctile Iron grate
n. The 461 Du
e head of
tio
Th
ca
.
pli
ted
ap
ipa
is
tic
is an
ble for th
rio. No bypass
aulically suita
e ACO Drain
na
dr
th
hy
sce
to
is
off
er
ate
ref
run
gr
The
opted
data. Please
ws from the ad
m the design
the requred flo
calculated fro
notes.
matical value
for a full list of
t
ee
Sh
n
tio
water is amath
enda
age Recomm
Surface Drain
Notes
Design Data
1
ga l/ mi n
3
te run
Length of gra
4.85"
g a l /m i n /ft
Asphalt
ss
rface roughne
Catchment su
grate
r approaching
Head of wate
t
n
e
m
e
v
a
fro m p
t o s t a t i c he a d
I nl e t fl o w r ate
hannel
ACO DRAIN c
rmation
General Info
1 9 .6 8 "
ft
19.68
47.55
l i nf l ow
D esi gn l ate ra
rface type
Catchment su
4
1.97"
a te
Design flow r ff in from catchment area)
(Liquid run o
3
s
a and result
d grate dat
e
d
n
e
m
m
o
c
Re
%
5
ope
)
Catchment sl
dicular to run
(Slope perpen
0 .4 2 "
0.013
2
0.075
84.01
K100S
5
i n ch e s
g a l /m i n
type
Type:
Material:
Part No:
d Class E
Type 461 slotte
Ductile iron
96752
Ref. No:
pacity.
e hydraulic ca O Office.
t has adequat
C
our nearest A
a channel tha
y
n
t
i
c
d
a
t
e
s
n
u
o
c
e
e
b
s
t
a
d mus
els ple
recommende
izing of chann
0%
g
s
n
i
t
10
t
c
a
s
e
r
r
r
g
ed
o
e
c
ce
h
e
T
ex
h
:
t
Note
formation on
aulic efficiency
For Further in
when the hydr
hibited.
ssing the grate
ion strictly pro
Water is bypa
ized reproduct
sed.
Date:
5 Total intake
grate
information
1.73"
1 Catchment
:
ACO Contact
www.acousa.com
hor
ation u
cts, Inc. unaut
ting the inform
Polymer Produ
ng and calcula
Copyright ACO
ken in compili
re has been ta
e area:
Grating intak
ation:
Hydraulic utiliz
20.13
20 6
2
i n /ft
%
Inc.
r Products,
ACO Polyme
na Road
12080 Raven
PO Box 245
44024
Chardon, OH
-7000
Tel: (440) 285
5-8517
Fax: (440) 28
) 543-4764
Toll free: (800
cousa.com
Email: info@a
com
www.acousa.
111
Technical Support
3. Run layout service and part scheduling
AutoCAD Design Service
ACO can provide a cost-effective surface
drainage solution to satisfy a project’s
design requirements. Trench drain layouts
will be designed to take full advantage of
existing and proposed site grades, utilizing
existing services where possible.
In order to produce a plan layout, the following information is required:
•
•
•
•
•
Plan of site showing elevations
Existence of any depth restrictions
Position and type of any plumbing fixtures/outlets
Position of any permanent structures
Liquid flow pattern and type of traffic (including traffic flow)
Results provided are:
•
•
AutoCAD printout provides:
1 Plan view of
2 Liquid flow
3 Position and
4 Trench and
type of outlet
directions
trench run
layout with
inverts
Plan layouts (AutoCAD) showing the trench drain positions relative to site structures
Installation drawings and specifications
grate type
Download details for all products,
loadings and pavements at www.
acousa.com/techserv
PROJECT NAME:
DS#: 106-001C
Garage Drainage
PROJECT LOCA
TION: Chardon, O
H
112
1
3
2
PRODUCT TYPE
: KlassikDrain K10
0S
GRATE TYPE: 461
Q Ductile Iron
REV.
DESCRIPTION
A
Added Additional
Leg of Trench
4
DATE: 10/19/05
SCALE: N.T.S.
DRAWN BY: TS
DRAWING LEGE
ND
CHECKED BY: TF
OC - Oulet/Closing
Cap
www.acousa.com
DATE:
4-BO - 4” Bottom
BY:
Out
let
6-BO - 6” Bottom
Outlet
HP INV. - High P
ACO Polymer Produc
ts,
12080 Ravenna Road, Inc.
P.O. Box 245
Chardon, Ohio 44024
Tel: (440) 285-7000
Fa
ACO DRAIN
ACO Scheduler
ACO has written a proprietary software
program, ‘Scheduler’, that shows trench
drain runs in profile. The program
automatically plots each run showing
positions of accessories, outlets, junctions,
etc. It automatically calculates a ‘Bill of
Materials’ for each run and totals multiple
runs to ensure the correct amount of parts
and pieces are ordered. ‘Scheduler’ plots
are particularly useful for installers.
Results provided are:
Sectioned profile of trench runs
Parts schedule fully itemizing parts and
pieces
•
•
PARTS SCHEDULE
Client:
Project Name:
Design File #:
ACO Polymer Products, Inc.
Garage Drain
106-001S
4
Part No.
Description
Quantity
2
2
‘Scheduler’ plot provides:
1 Profile view of
3 Positions and
2 Trench run
direction
change - e.g.,
90° corner or
junction
trench run
4 Detailed Bill of
Materials to
ensure all parts
are correctly
ordered
type of outlets
106-001S
04042
K2 Pre-sloped Channel
2
04043
K3 Pre-sloped Channel
2
04044
K4 Pre-sloped Channel
2
04045
K5 Pre-sloped Channel
2
04046
K6 Pre-sloped Channel
2
04047
K7 Pre-sloped Channel
2
04048
K8 Pre-sloped Channel
2
04049
K9 Pre-sloped Channel
2
04050
K10 Pre-sloped Channel
2
04051
K11 Pre-sloped Channel
1
04052
K12 Pre-sloped Channel
1
04053
K13 Pre-sloped Channel
1
04054
K14 Pre-sloped Channel
1
04055
K15 Pre-sloped Channel
1
04056
K16 Pre-sloped Channel
1
04057
K17 Pre-sloped Channel
1
04058
K18 Pre-sloped Channel
1
04059
K19 Pre-sloped Channel
04060
K20 Pre-sloped Channel
1
1
96804
K900 in-line catch basin
1
96752
Type 461Q Class E ductile slot - 19.69" (0.5m) grating
61
02899
Locking Part for Type 461Q Class E ductile slot - 19.69" (0.5m) grating
61
ACO Polymer Products Design Servic
Prepared By: ACO-SS 2.07
Page 1 of 1
, 16-Mar-04
113
2
RUN BEND
90º
1
END
CAP
K3
K1
K2
K4
K6
K19
K9
K7
K5
K8
K10
3
K20
K17
K18
K15
K16
K900
in-line
catch basin
www.acousa.com
K13
K14
K11
K12
K9
K10
K7
K8
K5
K6
K3
K4
K1
K2
END
CAP
Technical Support
4. Ponding analysis
Temporary ponding is a short lived flood
situation, which, in some circumstances,
can be tolerated allowing an intentionally
undersized trench drain system. It allows a
more economical system to be used that
will work effectively under most weather
conditions, but will be slightly under
designed for heavy storms.
Ponding analysis should only be considered
where buildings and property are not in
close proximity to the drainage system to
minimize risk of damage. It is an ideal option
for the outer areas of large parking lots,
distribution yards, etc., (Risk Analysis).
In order to produce a ponding analysis, the following information is required:
•
•
•
Full information required to run the ‘Hydro’ plot - see page 110
Plan of site showing elevations
Existence of any buildings
Results provided are:
•
•
Plot showing extent of ponding
Average duration of ponding
The ponding analysis map shows the size
and duration of the flood.
Ponding analysis shows:
1 Design
2 Trench drain
discharge
ACO DRAIN
114
Runoff Scena
rio
2 KS030
Constant
Channel s
3 Run-off scenario
4 Width of
size and type
5 Visual map of
PONDING AN
ALYSIS
Project:
Client:
Address:
DS#:
3
6 Project notes
worst ponding
scenario
temporary
ponding
New parking
lot
ACO Polymer
Products, Inc
12080 Ravenn
a Road, Chard
on, OH 4402
106-001H
4
Catchment G
eometry (Cro
Constant L ater
al Runof f , q =
1.256 l /s/m
ss-Section)
4
Ponding Width
Catchment
Fl ow,
Q = 62.8 l /s
Run L ength to
Outl et, L (m) @
S = 0.5%
1
130mm
L ongi tudi nal G
roundsl ope
KS030
Channels
Ponding Map
Maximum wid
th
of ponding 3.3
m
2.5% (1 in 40)
Crossfall
16.7% (1 in 6)
Crossfall
Ponding
Depth
Cross-Section
of
Temporary Po
nding
5
Average width
of ponding 0.8
m
Extent of pond
ing
Flow direction
Outlet end
Length of pond
ing - 5.2m
Notes:
6
6m run length
to outlet 0.06%
Dr awi ngs
Not t o Scal e
groundslope
1. The hydrau
lics of the AC
O Drain Syste
Scenario abov
m were calcu
e.
lated based on
2. The extent
the assumed
of ponding, de
Runoff
pt
h and width, we
(Cross-Sectio
re determined
n) with 16.7%
from the Catch
(1 in 6) crossfa
3. For a summ
ment Geomet
ll.
ary of the exte
ry
nt of ponding
, please refer
www.acousa.com
to the Pond
ing Analysis Sh
eet.
Plo t n um b er :
106-001H
ACO Polymer Prod
12080 Ravenna ucts, Inc.
Road, P.O. Box 245
Chardon, Ohio 440
Tel: (440) 285-700 24
Fax: (440) 285-8510
7
Email: info@
ACO DRAIN
5. Chemical resistance
ACO Drain channel bodies are highly
resistant to chemical attack and, with the
appropriate grate, can be used in most
environments where acids and dilute alkalis
are encountered.
Refer to chemical chart below for
resistance of Polyester and Vinyl ester
polymer concrete. FlowDrain products use
the same polyester resin - refer to Polyester
details for chemical resistance.
Chemical Medium
Max. Short time Long time
conc.. exposure exposure
72 hours
42 days
Polyester
Max. Short time Long time
conc.. exposure exposure
72 hours
42 days
Vinyl ester
Acetic Acid
Acetone
Ammonia
Aniline
Aniline in Ethyl Alcohol
Benzene
Boric Acid
Butyric Acid
Butyl Alcohol
Calcium Chloride
Calcium Hydroxide
Caster Oil
Chloric Acid
Chromic Acid
Citric Acid
Diesel Fuel
Ethanol
Ethlendiamine
Ethyl Acetate
Ferrous Sulfate
Fluorallic Acid
Formaldehyde
Formic Acid
Fuel Oil
Gasoline
n-Heptane
n-Hexane
Hydraulic Oil
Hydrochloric Acid
Hydrofluoric Acid
JP4
JP8
Lactic Acid
Methanol
Methyl Amine
Methyl Ethyl Ketone
Mineral Oil SAE5W50
Monochlor Benzene
Monochloroacetic Acid
Nitric Acid
n-Nonane
Iso-Octane
Oxalic Acid
Phenol
Phosphoric Acid
Potassium Hydroxide
Sodium Acetate
Sodium Carbonate
Sodium Chloride
Sodium Hydroxide
Sodium Hypochloric
Sulfuric Acid
Tetrafluoroborsaure
Toluene
Trichloroethylene
Triethylamine
Xylene
30%
10%
10%
100%
10%
100%
100%
25%
100%
100%
100%
100%
5%
5%
100%
100%
100%
100%
100%
30%
10%
35%
10%
100%
100%
100%
100%
100%
10%
5%
100%
100%
10%
5%
100%
100%
100%
0.05%
10%
10%
100%
100%
100%
100%
10%
10%
100%
20%
100%
15%
5%
40%
20%
100%
100%
100%
100%
75%
10%
10%
100%
10%
100%
100%
50%
100%
100%
100%
100%
5%
20%
100%
100%
95%
100%
100%
100%
10%
100%
10%
100%
100%
100%
100%
100%
37%
20%
100%
100%
100%
5%
100%
100%
100%
0.05%
10%
20%
100%
100%
100%
100%
75%
10%
100%
35%
100%
25%
5%
70%
20%
100%
100%
100%
100%
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
U
D
D
D
U
D
D
D
D
D
D
D
U
D
D
D
D
D
D
D
D
U
D
D
U
U
U
U
D
U
D
D
D
D
U
D
U
D
D
D
U
D
U
D
D
D
U
D
D
D
D
D
D
U
D
D
D
U
U
U
D
U
D
U
D
U
D
U
D
U
U
D
D
U
D
D
U
U
U
D
U
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
U
D
D
Note: Maximum operating temperature of 180°F (82°C)
www.acousa.com
D
U
U
U
D
U
D
D
D
D
D
D
D
D
D
D
D
D
U
D
D
D
D
D
D
D
D
D
D
D
D
D
D
U
U
U
D
D
D
D
D
U
D
U
D
D
D
D
D
D
D
D
D
U
U
D
U
When greater chemical resistance is
required, Vinyl ester polymer concrete
channels should be specified.
These recommendations are for guidance
only. Customers are advised to test a coupon
of polymer concrete to ensure suitability.
Test coupons are available free of charge
from ACO.
Polymer concrete is not affected by road
de-icing salts, and conforms to ASTM
- B117 Salt Spray Test.
Important considerations
for chemical environments
When reviewing potential applications
of trench drains in chemical environments,
the following issues should be considered;
1.
2.
3.
4.
Type(s) & mixture of chemical(s).
Concentration percentages.
Contact time with trench system.
Temperatures of chemicals flowing into
the trench drain. 180°F (82°C) max.
5. Flushing system employed to clear
chemicals from the system.
6. Cleaning agents should be checked for
compatibility with trench materials.
7. ACO coupons can be used for final
determination of chemical resistance.
8. Grate, locking mechanism, edge rail,
outlet and trash bucket materials should
be checked for chemical resistance.
9. Check sealant for compatibility.
Note:
If ACO Drain standard products are unable
to provide adequate chemical resistance,
contact Aquaduct (800) 662-2377 for a
custom product solution.
115
Installation
Trench drain construction methods
Method of construction is determined
by location, size, cost and performance
requirement.
Wooden formwork
Trench drains can be constructed by either:
1. Cast-in-place
Formwork used to create trench in
surrounding concrete
• Used mainly in concrete pavements
• Costly, complex formwork to construct
on site
• Care required to ensure frame and grate
are fully supported by surrounding
concrete - good vibration essential during
concrete pour
• Difficulties in achieving level grate
seating
• Hydraulic performance poor due to rough
internal finish. Trenches susceptible to
biological growth
• Difficulties creating a hydraulically
efficient ‘U’ or ‘V’ shape bottom (cast-inplace usually has square base detail,
which has poor hydraulic characteristics)
• Difficulties in achieving sloped system
- formwork becomes even more complex
adding to installation time and labor
• Quality of finish can vary greatly,
depending on contractor
116
Trench forming systems, such as ACO FastForm,
are designed to alleviate many of these issues.
Step 1
Excavate trench
Step 2
Create formwork
for trench base
Step 3
Pour trench base
Step 4
Create formwork
for trench walls
Step 5
Position and
support frames
Step 6
Pour trench walls
Step 7
Remove formwork
Step 8
Patch walls and
grout base if slope
required
FastForm formers
Step 1
Excavate trench
See page 70 for details on FastForm.
Step 2
Assemble and
position former in
trench and level
Step 3
Pour concrete
surround
Step 4
Strip formers
2. Modular systems
Factory produced channel units that
connect together to create trench drain
• Some products can be used in a variety
of pavement types
• Neat aesthetic appearance
• Quick to install
• Hydraulically efficient due to smooth
surface and profiled bottom
• Easier to secure grates
• Consistent quality due to factory
controlled production of channels
• Cost effective when labor and material
costs taken into account
• Easier to estimate costs
• Less maintenance required
Modular systems
Step 1
Excavate trench
Step 2
Create concrete
support patty or
position installation
devices
www.acousa.com
Step 3
Position and level
channels
Step 4
Pour concrete
surround
ACO DRAIN
Site work
ACO provides separate installation details
for each product with comprehensive on-site
advice, when appropriate.
Ground conditions
Specific ground conditions or contaminated
ground may call for a deeper/wider concrete
surround or larger haunch than minimum
recommendations.
If in doubt, seek engineering advice.
Temporary installation
Thermal movement
Longitudinal expansion joints, (which
occasionally may be doweled horizontally
and de-bonded), will isolate the trench
and the concrete haunch from thermal
movement of large concrete slabs.
If transverse joints in the concrete slab are
required, the joints should be positioned
to coincide with channel-to-channel joints.
Alternatively the channel may be cut to suit
the expansion joint and resealed with a
suitable flexible sealant.
3 feet
3 feet
Joint sealing
Where channels are installed in suspended
slabs, it is important that the complete
installation is watertight. All channel-tochannel and channel-to-fitting joints should
be sealed with appropriate sealant.
Sealant should be resistant to the same
chemicals as the trench material and be
flexible to allow for any movement from
the slab and from temperature changes.
Surfaces should be correctly prepared prior
to applying sealant to ensure good adhesion.
Contact ACO Technical Department, or
go to www.acousa.com/techserv
for Technical Bulletin.
Longitudinal expansion joint
Certain ACO channels are supplied with an
‘SF Sealant Groove’ as standard (SlabDrain
- Page 78 and ChemDrain - Page 84).
This provides a groove that can be filled
with an appropriate flexible sealant to
create a watertight joint. This is of particular
importance with elevated slabs and where
liquids may contain chemicals or oils.
During site work and after the trench
run is laid, the top of the trench can be
vulnerable to damage. Site traffic should be
routed away from the trench. If temporary
crossings are required, a base course of
minimum width 3 feet should be installed
either side of the trench for protection.
Loose boards or plates are inadequate.
Transverse expansion joint
Engineering advice should be sought
for designing expansion joints.
Site work accessories
Description
Part
No
Weight
lbs
Seals and patch materials
ACO Seal flexible joint sealant - 10oz
ACO Bond - polymer concrete repair kit - 1 gallon
ACO Bond - polymer concrete repair kit - 5 gallons
ACO Bond VE - Vinyl ester repair kit - 1 gallon
ACO Fiberglass repair kit - 1 gallon
91120
06519
06516
06515
08203
1.0
11.0
55.0
11.0
11.0
Accessories
Shovel head for 4” channels
01315
2.0
www.acousa.com
Sealant applied with caulk gun
117
Installation
Installation
Channel units are installed in a continuous
trench, and are fully encased with concrete.
Full installation instructions are available in the
Site Installation Manual, call for copies or go
to www.acousa.com/installation.htm.
1. Excavation
Excavate trench to accommodate trench
drain system. Excavation should be made
around the center line.
Excavation must be sufficient enough to
accommodate each of the following:
• Channel/catch basin width and depth
dimensions.
• Concrete surround dimensions - a minimum
of 4” (Load Class A) of concrete on all
sides, allow 6” for FlowDrain products
to accommodate installation brackets.
Specific loading and ground conditions will
increase the excavation size.
See page 120 for further guidelines.
• For sloped systems, excavate base to
roughly follow fall of trench drain run.
3. Trench drain installation
Channel units need to be supported at
correct height and held securely in place to
avoid movement during concrete pour.
2. Layout and outlet installation
All installations should start from the outlet
point. For sloped trench systems, polymer
concrete catch basin drill-outs match every
5th channel unit.
• Determine type of outlet required and its
position
• Install the outlet channel/catch basin and
set haunch
• Select numbered sloping channels in
order from deepest (highest channel
number) to shallowest
• Install channels working away from outlet
a. Polymer concrete products
For new construction use either patty
supports or installation devices. For retrofit
into an existing slab, channels can be hung
Patty supports
Care should be taken that concrete is not
trapped in joint between channels.
Concrete patties at intervals, away from joints
around frost keys
Ensure all loose material is removed and
base is compacted.
118
There are a number of options available to
support channel units.
Installation devices - see page 55
Run string line and laser level at finished
surface level along full length of excavation
to ensure trench is installed at correct grade.
String
line
Channel clamp holds channel joints, and rebar
allows height adjustment & leveling
Hanging method - see page 55
2 x 4 slides through pocket
at top of bracket
Install from outlet
Bracket fits into
locking bar recess
b. Fiberglass and FastForm products
Products have installation devices attached
to frames to allow trench to be held in
position by No. 4 or 5 rebar. FlowDrain can
also be hung from grate locking.
Outlet
www.acousa.com
ACO DRAIN
4. Channel bracing
To prevent channel walls and joints being
distorted by pressure of concrete, grates (or
plywood cut to a snug fit) should be installed
in channel.
Wood
6. Pavement finishing
Top of adjacent pavement must be above
grating level by approximately 1/8” (3 mm).
Brick pavers should be set approx. 1/8”
(3mm) above trench edge. First brick course
should be set on mortar/concrete.
Shims/Washers
Care should be taken with asphalt rolling
machines to avoid damage to trench edge.
Approx. 45o
Finish concrete to
have slight slope
down to trench
1
/8” (3mm)
Maintenance
Regular inspections of the trench drain are
recommended. Frequency will depend on
local conditions and environment, but should
be at least annually.
Grate
Inspections should cover:
• Grates and locking devices
• Catch basins and trash buckets
• Concrete surround and adjacent paving
Grates should be suitably wrapped to
protect from concrete splash.
Shims or washers placed along each side
allow easy removal of the grating.
All items should be inspected for damage,
blockage or movement. Compare with site
drawings if necessary.
5. Concrete pour
Concrete should have compressive strength
of minimum 3,000 psi.
Maintenance guidelines:
1. Remove grates
2. Remove debris from channel - a 4” shovel
head is available (Part # 01315)
3. Flush channels with water or high pressure
washer (do not use boiling water or
aggressive cleaning agents)
4. Repair damaged surfaces where
necessary with an appropriate ACO repair
kit - see page 117
5. Renew joint seals as required
6. Empty trash buckets and
clean out pipe connections
7. Re-install trash bucket
8. Re-install grates, ensuring they are locked
back in place
119
Concrete should be poured evenly (both
sides of channel) and carefully to avoid
dislodging channels. A wand type vibrator
should be used to ensure concrete
distributes evenly underneath and around
channels.
7. Completing trench installation
• Remove grates and remove protective
wrapping.
• Remove debris from trench drain and
make sure outlet pipes are clear.
• Install trash buckets in catch basins,
if required.
• Flush trench run to check for pipe work
blockages, unblock if necessary.
• Empty trash buckets and clean out pipe
connections, if necessary. Re-install trash
buckets.
• Re-install grates in proper position
ensuring they are securely locked down.
The trench drain is now ready for use.
www.acousa.com
Installation Sections
Installation sections
BLOCK PAVERS - DIN 19580 Class B
An installed ACO Drain System should
incorporate the following:
• Correct grate type
• Correct channel type and size
• Minimum grade 3,000psi compressive
strength cement concrete surround.
B
Paving blocks
Paving sand
or mortar
Bedding layer
Soil
It is recommended that the cement concrete
surround must be durable and conform to
minimum strength requirements, shown in
the illustrations. Poor site conditions and
low load bearing pavement will require an
increase in these dimensions to meet both
vertical and lateral loads.
4“ (100mm)
4“ (100mm)
4“ (100mm)
These illustrations are a guide for average
ground conditions only. Installation drawings
are available at www.acousa.com/install_
drawings_drain.htm.
Note:
1. Grate should be 1/8” (3 mm) below pavement surface
If in doubt, seek engineering advice.
ASPHALT - DIN 19580 Class C
C
Asphalt wearing course
CONCRETE - DIN 19580 Class C
C
Cement concrete slab
120
Expansion joint to
engineers details
Base course
Road course
Bedding layer
Sub base
Soil
4“ (100mm)
4“ (100mm)
4“ (100mm)
4“ (100mm)
4“ (100mm)
4“ (100mm)
Note:
1. Grate should be 1/8” (3 mm) below pavement surface
Note:
1. Grate should be 1/8” (3 mm) below pavement surface
2. To allow for installation brackets on FlowDrain products, a minimum 8”
(200mm) surround will be required
www.acousa.com
ACO DRAIN
BLOCK PAVERS - DIN 19580 Class C
C
ASPHALT - DIN 19580 Class E
E
Asphalt wearing course
Paving blocks
Concrete surround
Concrete surround
Paving sand
or mortar
Base course
Road course
Bedding layer
Sub base
Soil
4“ (100mm)
6“ (150mm)
4“ (100mm)
6“ (150mm)
4“ (100mm)
6“ (150mm)
Note:
1. Grate should be 1/8” (3 mm) below pavement surface
2. To allow for installation brackets on FlowDrain products, a minimum 8”
(200mm) surround will be required
Note:
1. Grate should be 1/8” (3 mm) below pavement surface
2. To allow for installation brackets on FlowDrain products, a minimum 10”
(250mm) surround will be required
CONCRETE - DIN 19580 Class E
CONCRETE - DIN 19580 Class F
E
F
Cement concrete slab
Cement concrete slab
Expansion joint to
engineers details
Expansion joint to
engineers details
121
Bedding layer
Bedding layer
Soil
Soil
6“ (150mm)
8“ (200mm)
6“ (150mm)
8“ (200mm)
6“ (150mm)
8“ (200mm)
Note:
1. Grate should be 1/8” (3 mm) below pavement surface
2. To allow for installation brackets on FlowDrain products, a minimum 10”
(250mm) surround will be required
Note:
1. Grate should be 1/8” (3 mm) below pavement surface
www.acousa.com
Volumetric Channel Capacities
For projects where trenches are used to
hold liquid, such as sustainable drainage
projects or chemical containment, channel
volumes are required to calculate holding
capacity.
The following tables provide volumetric
capacities for each channel and catch basin.
Volumes are calculated up to grate seat
only. Add together total of channels used.
Product Type
Product Type
Channel #
122
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
K100S/
S100K
2.22
2.38
2.54
2.70
2.86
3.02
3.18
3.34
3.50
3.66
3.82
3.98
4.14
4.30
4.46
4.62
4.78
4.94
5.10
5.26
5.42
5.58
5.74
5.90
6.06
6.22
6.37
6.54
6.70
6.86
S300K
Channel #
FG100
Gallons
2.22
2.38
2.54
2.70
2.86
3.02
3.18
3.34
3.50
3.66
3.82
3.98
4.14
4.30
4.46
4.62
4.78
4.94
5.10
5.26
5.42
5.58
5.74
5.90
6.06
6.22
6.37
6.54
6.70
6.86
20.74
21.21
21.69
22.16
22.63
23.10
23.57
24.04
24.51
24.98
25.45
25.92
26.39
26.86
27.33
27.80
28.27
28.74
29.21
29.68
30.15
30.62
31.09
31.56
32.03
32.50
32.97
33.44
33.91
34.38
1
2
3
4
5
6
7
8
9
10
11
12
Gallons
10.81
18.37
12.93
22.58
15.06
26.79
17.18
31.00
19.30
35.21
21.42
39.42
23.54
43.63
25.66
47.84
27.78
52.05
29.90
56.26
60.47
64.68
Neutrals
01
0013
02
010
0103
020
0203
030
0303
2.12
1.06
3.68
1.84
5.30
2.65
6.88
3.44
2.29
3.55
1.77
5.14
2.57
6.72
3.36
20.5
25.24
30.00
34.70
17.35
6.50
20.50
31.00
9.50
6.50
20.50
31.00
9.50
24.00
34.50
9.50
FG200
Neutrals
404N
404N-1
407N
407N-1
410N
410N-1
803N
803N-3
806N
806N-3
809N
809N-3
812N
812N-3
18.20
6.06
24.60
8.20
30.98
10.32
-
28.80
9.60
41.50
13.83
54.10
18.00
66.76
22.25
F900
F660
F880
9.00
27.00
55.00
27.00
55.00
Product Type
Channel #
80 depth
100 depth
Channel #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
H100
1.16
1.70
H100K H100SK
Gallons
1.16
1.70
Product Type
Channel #
MiniKlassik
MiniKlassik
Gallons
0.64
www.acousa.com
1.18
FF300
FF600
Gallons
21.19
82.20
26.19
92.20
31.19
102.20
36.19
112.20
41.19
122.20
46.19
132.20
51.19
142.20
56.19
152.20
61.19
162.20
66.19
172.20
71.19
182.20
76.19
192.20
81.19
202.20
86.19
212.20
91.19
222.20
96.19
232.20
101.19
242.20
106.19
252.20
111.19
262.20
116.19
272.20
Neutrals
05
010
015
020
43.60
68.57
93.50
118.44
127.20
177.04
226.90
276.77
42.00
100.00
100.00
Catch Basins
12" x 24"
24" x 24"
Catch Basins
Catch Basins
900 In-line
SK3 - short
SK3 - deep
620 ass.
630 ass.
611 riser
Product Type
C100
Notes:
1. To calculate cubic inches, multiply by 231
2. Use K100S/S100K figures for KS100S,
CK100S and CS100K
3. Use H80/H100/H80K/H100K and H100SK
figures for CH80/CH100/CH80K/CH100K
and CH100SK
4. SK3 - short is SK3-900 top with short base
5. SK3 - deep is SK3-900 top with deep base
ACO DRAIN
Glossary
AASHTO - American Association of State
Highway & Transportation Officials.
Female - has recessed details to interconnect
with a male piece to enable a good fit.
ADA - Americans with Disability Act - see
page 24.
Formers - box like shapes to create a
recess in the concrete slab that act as a
trench system.
Anti-shunt lugs - protrusions on edge rail
that fit into recesses in grate to prevent lateral
movement - see PowerDrain page 42.
AS3996 - Australian Trench Drain Standard
detailing Bicycle Safe grate specifications
- see page 25.
ASME - American Society of Mechanical
Engineers.
ASTM - American Society for Testing and
Materials.
Foul air trap - shaped pipe section
to prevent odors traveling up from
underground waste water system.
Free area - area for water flow.
Determined by clear opening (width) and
invert depth - see page 12.
Manning’s equation - (steady uniform flow)
common method for calculating flow in pipes
or culverts. Does not allow for lateral intake
of liquids - see page 11.
Manning’s roughness coefficient measure of roughness of a material’s surface
- see page 22.
Non-uniform flow - irregular flow in trench
due to continuous lateral intake - see page
11.
Open swale - dish in paved area with little
depth and no grate.
FRP - fiber reinforced plastic.
‘GIC’ - ACO’s proprietary software program
to calculate grate intake hydraulics - see
page 111.
Bell end - flared end of pipe to accept a
certain pipe size inside - similar to coupler.
GPM - Gallons per Minute - measure of flow.
Bicycle safe - grate with slots that reduce
‘tram-lining’ of tires - see page 25.
Grade - angle of slope on pavement - see
page 13.
Bolt sizes - figures provide diameter - pitch
per inch x length (from seat of head to base).
Gray iron - pig iron melted in a furnace and
poured into molds.
Catchment area - paved area that will
collect liquids - see page 12.
Grate hydraulics - performance of liquid
entering through grate openings - see page
15.
Overall depth - depth from top of grate to
underside of channel.
Pavement - paved area surrounding trench.
Plain end - section of pipe, will require
coupler connection.
PowerLok - ACO’s patented boltless locking
system consisting of a sliding clip that locks
onto the edge rail - see page 43.
psi - pounds per square inch.
Cast-in-place - trench that is produced
during concrete pour by removable forms.
Catch basin - large basin to collect liquid
into underground pipe work.
CFS - cubic foot per second - measure of flow.
Channel - individual modular unit.
Chemical resistance - ability to withstand
specified chemicals.
Corrosion resistance - ability to withstand
weathering.
DIN 19580 - Deutsches Industrielle Norm - load
standard specifically written for trench drains,
superseded by EN 1433 - see page 17.
Drill-outs - shaped recesses cast in
polymer concrete to enable easy removal of
material for pipe/channel connection.
Ductile iron - pig iron with magnesium added
to provide added flexibility and strength. Often
referred to as spheroidal graphite (SG) iron.
Edge protection - metal edge rail to prevent
impact or general damage to trench body
- see page 23.
EN 1433 - international load standard
supersedes DIN 19580 - see page 17.
Ground slope - percentage of slope along
length of trench.
'Heelsafe' - maximum grate hole size in
least dimension of 0.31”, deemed safe for
high-heeled shoes - see page 25.
‘Hydro’ - ACO’s proprietary software
program to accurately calculate trench
hydraulics - see page 110.
Hydrological cycle - cycle of water from
oceans to rainfall and back to the ocean.
In-line catch basin - similar width basin
connected to trench which acts as exit point
to underground pipe work.
Invert depth - depth from top of grate to
inside base of channel - see page 12.
kN - kilonewton - measurement of force,
1kN = 224.8lbs (102kg) of force.
LEED (Leadership in Energy and
Environmental Design) - promotes a
whole building approach to sustainability
- see page 7.
Lateral intake - liquid entering the trench
from surrounding paved area.
Male - has protruding details to interconnect
with a female piece to enable a good fit.
FAA-AC - Federal Aviation Administration
- Advisory Circular.
www.acousa.com
QuickLok - ACO’s patented boltless locking
system consisting of shaped stud and spring
clip - see page 36.
‘Scheduler’ - ACO’s proprietary software
program to illustrate/profile trench layouts
- see page 113.
SF groove - void at channel joint to allow
application of a sealant - see SlabDrain
page 78 and ChemDrain - page 84.
123
Socket - recess to accept a certain pipe
size inside - similar to a coupler, see also
‘Bell end’.
Spigot - section of pipe, will require a
coupler connection, see also ‘Plain end’.
Stainless steel - mild steel with a minimum
of 11% chromium added to provide
enhanced corrosion resistance. There are
a wide number of stainless steels available,
each with differing properties. ACO grates
are Grade 304 austenitic stainless steel.
Steady uniform flow - constant level of
flow in trench/pipe. See Manning’s Equation.
Sustainable Drainage (SUDS) - collection,
treatment and reuse of rainwater - see page 7.
Trench - complete drain system in paved area.
USGBC (U.S. Green Building Council) promotes buildings that are environmentally
responsible, profitable and healthy places to
live and work - see page 7.
Part Index
Part # Description
124
00549
00985
01315
01318
01498
01614
02899
03314
04035
04040
04041
04042
04043
04044
04045
04046
04047
04048
04049
04050
04051
04052
04053
04054
04055
04056
04057
04058
04059
04060
04061
04062
04063
04064
04065
04066
04067
04068
04069
04070
04071
04780
05511
05512
05513
05514
05515
05516
05517
05518
05519
05520
05521
05522
05523
05524
05525
05526
05527
05528
05529
05530
05531
05532
H100 Neutral channel - 39.37"
H80 Neutral channel - 39.37"
Shovel head for 4” channels
QuickLok/PowerLok grate tool
Series 900 plastic trash bucket
Type 612 catch basin base - short
QuickLok locking bar
Type 478Q - ductile iron ADA grate
K0013 Neutral channel - 19.69"
K01 Neutral channel - 39.37"
K1 Sloped channel - 39.37"
K2 Sloped channel - 39.37"
K3 Sloped channel - 39.37"
K4 Sloped channel - 39.37"
K5 Sloped channel - 39.37"
K6 Sloped channel - 39.37"
K7 Sloped channel - 39.37"
K8 Sloped channel - 39.37"
K9 Sloped channel - 39.37"
K10 Sloped channel - 39.37"
K11 Sloped channel - 39.37"
K12 Sloped channel - 39.37"
K13 Sloped channel - 39.37"
K14 Sloped channel - 39.37"
K15 Sloped channel - 39.37"
K16 Sloped channel - 39.37"
K17 Sloped channel - 39.37"
K18 Sloped channel - 39.37"
K19 Sloped channel - 39.37"
K20 Sloped channel - 39.37"
K21 Sloped channel - 39.37"
K22 Sloped channel - 39.37"
K23 Sloped channel - 39.37"
K24 Sloped channel - 39.37"
K25 Sloped channel - 39.37"
K26 Sloped channel - 39.37"
K27 Sloped channel - 39.37"
K28 Sloped channel - 39.37"
K29 Sloped channel - 39.37"
K30 Sloped channel - 39.37"
MiniKlassik channel galvanized rail
Type 492Q - resin composite grate
C1 Sloped channel - 39.37"
C2 Sloped channel - 39.37"
C3 Sloped channel - 39.37"
C4 Sloped channel - 39.37"
C5 Sloped channel - 39.37"
C6 Sloped channel - 39.37"
C7 Sloped channel - 39.37"
C8 Sloped channel - 39.37"
C9 Sloped channel - 39.37"
C10 Sloped channel - 39.37"
C11 Sloped channel - 39.37"
C12 Sloped channel - 39.37"
C13 Sloped channel - 39.37"
C14 Sloped channel - 39.37"
C15 Sloped channel - 39.37"
C16 Sloped channel - 39.37"
C17 Sloped channel - 39.37"
C18 Sloped channel - 39.37"
C19 Sloped channel - 39.37"
C20 Sloped channel - 39.37"
C21 Sloped channel - 39.37"
C22 Sloped channel - 39.37"
Page
83
83
117
33
33
53
33
39
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
105
37
91
91
91
91
91
91
91
91
91
91
91
91
91
91
91
91
91
91
91
91
91
91
Part # Description
05533
05534
05535
05536
05537
05538
05539
05540
05542
05543
05544
05545
05546
05547
05548
05606
05607
05608
05609
05641
05654
05655
05656
05935
05939
05960
05961
05962
05963
05969
06515
06516
06519
06553
06667
06676
06681
06682
06683
06684
06685
06686
06687
06688
06689
06690
06691
06692
06693
06694
06695
06696
06697
06698
06699
06700
06701
06702
06703
06704
06705
06706
06707
06708
Page
C23 Sloped channel - 39.37"
91
C24 Sloped channel - 39.37"
91
C25 Sloped channel - 39.37"
91
C26 Sloped channel - 39.37"
91
C27 Sloped channel - 39.37"
91
C28 Sloped channel - 39.37"
91
C29 Sloped channel - 39.37"
91
C30 Sloped channel - 39.37"
91
C02 Neutral channel - 39.37"
91
C010 Neutral channel - 39.37"
91
C020 Neutral channel - 39.37"
91
C030 Neutral channel - 39.37"
91
C0103 Neutral channel - 19.69"
91
C0203 Neutral channel - 19.69"
91
C0303 Neutral channel - 19.69"
91
C306 Closing cap
91
C108-4 4" Outlet cap
91
C208-4 4" Outlet cap
91
C308-4 4" Outlet cap
91
Type 614 catch basin base - deep
53
C104-4 4" Inlet cap
91
C204-4 4" Inlet cap
91
C304-4 4" Inlet cap
91
H80 Closing cap
83
H100 Closing cap
83
CH80 Neutral channel - 39.37"
97
CH100 Neutral channel - 39.37"
97
CH80 Closing cap
97
CH100 Closing cap
97
Type C614 catch basin base - deep 53
ACO Bond Vinyl ester repair kit
117
ACO Bond polymer repair kit
117
ACO Bond polymer repair kit
117
C900 In-line catch basin - 19.69"
91
Channel clamp
54
CK01 Neutral channel - 39.37"
93
CK1 Sloped channel - 39.37"
93
CK2 Sloped channel - 39.37"
93
CK3 Sloped channel - 39.37"
93
CK4 Sloped channel - 39.37"
93
CK5 Sloped channel - 39.37"
93
CK6 Sloped channel - 39.37"
93
CK7 Sloped channel - 39.37"
93
CK8 Sloped channel - 39.37"
93
CK9 Sloped channel - 39.37"
93
CK10 Sloped channel - 39.37"
93
CK11 Sloped channel - 39.37"
93
CK12 Sloped channel - 39.37"
93
CK13 Sloped channel - 39.37"
93
CK14 Sloped channel - 39.37"
93
CK15 Sloped channel - 39.37"
93
CK16 Sloped channel - 39.37"
93
CK17 Sloped channel - 39.37"
93
CK18 Sloped channel - 39.37"
93
CK19 Sloped channel - 39.37"
93
CK20 Sloped channel - 39.37"
93
CK21 Sloped channel - 39.37"
93
CK22 Sloped channel - 39.37"
93
CK23 Sloped channel - 39.37"
93
CK24 Sloped channel - 39.37"
93
CK25 Sloped channel - 39.37"
93
CK26 Sloped channel - 39.37"
93
CK27 Sloped channel - 39.37"
93
CK28 Sloped channel - 39.37"
93
www.acousa.com
Part # Description
06709
06710
06722
06738
06740
06750
06751
06752
06753
06754
06755
06756
06757
06758
06759
06760
06761
06762
06763
06764
06765
06766
06767
06768
06769
06770
06771
06772
06773
06774
06775
06776
06777
06778
06779
06780
06790
08203
31530
31531
31540
31541
31550
31551
31630
31631
31640
31641
31650
31651
90003
90015
90027
90032
90044
90056
90069
90078
90080
90091
90106
90112
90128
90139
Page
CK29 Sloped channel - 39.37"
93
CK30 Sloped channel - 39.37"
93
CK0013 Neutral channel - 19.69"
93
Type C612 catch basin base - short 53
KS01 Neutral channel - 39.37"
35
MiniKlassik channel stainless rail
105
KS1 Sloped channel - 39.37"
35
KS2 Sloped channel - 39.37"
35
KS3 Sloped channel - 39.37"
35
KS4 Sloped channel - 39.37"
35
KS5 Sloped channel - 39.37"
35
KS6 Sloped channel - 39.37"
35
KS7 Sloped channel - 39.37"
35
KS8 Sloped channel - 39.37"
35
KS9 Sloped channel - 39.37"
35
KS10 Sloped channel - 39.37"
35
KS11 Sloped channel - 39.37"
35
KS12 Sloped channel - 39.37"
35
KS13 Sloped channel - 39.37"
35
KS14 Sloped channel - 39.37"
35
KS15 Sloped channel - 39.37"
35
KS16 Sloped channel - 39.37"
35
KS17 Sloped channel - 39.37"
35
KS18 Sloped channel - 39.37"
35
KS19 Sloped channel - 39.37"
35
KS20 Sloped channel - 39.37"
35
KS21 Sloped channel - 39.37"
35
KS22 Sloped channel - 39.37"
35
KS23 Sloped channel - 39.37"
35
KS24 Sloped channel - 39.37"
35
KS25 Sloped channel - 39.37"
35
KS26 Sloped channel - 39.37"
35
KS27 Sloped channel - 39.37"
35
KS28 Sloped channel - 39.37"
35
KS29 Sloped channel - 39.37"
35
KS30 Sloped channel - 39.37"
35
KS0013 Neutral channel - 19.69"
35
ACO Fiberglass repair kit - 1 gallon 117
Type 420Q - galvanized steel grate
37
Type 421Q - galvanized steel grate
37
Type 425Q - galvanized steel grate
38
Type 426Q - galvanized steel grate
38
Type 435Q - galvanized steel grate
39
Type 436Q - galvanized steel grate
39
Type 450Q - stainless steel grate
37
Type 452Q - stainless steel grate
37
Type 455Q - stainless steel grate
38
Type 457Q - stainless steel grate
38
Type 490Q - stainless steel grate
39
Type 493Q - stainless steel grate
39
SK01 Neutral channel - 39.37"
47
SK1 Sloped channel - 39.37"
47
SK2 Sloped channel - 39.37"
47
SK3 Sloped channel - 39.37"
47
SK4 Sloped channel - 39.37"
47
SK5 Sloped channel - 39.37"
47
SK6 Sloped channel - 39.37"
47
SK7 Sloped channel - 39.37"
47
SK8 Sloped channel - 39.37"
47
SK9 Sloped channel - 39.37"
47
SK10 Sloped channel - 39.37"
47
SK010 Neutral channel - 39.37"
47
SK0103 Neutral channel - 19.69"
47
SK11 Sloped channel - 39.37"
47
ACO DRAIN
Part # Description
90141
90154
90166
90173
90181
90198
90209
90210
90221
90235
90249
90255
90263
90274
90282
90291
90306
90318
90321
90337
90340
90392
90401
90404
90405
90417
90418
90426
90427
90431
90432
90448
90449
90455
90456
90463
90464
90472
90473
90481
90482
90497
90498
90506
90507
90514
90515
90522
90523
90539
90540
90541
90542
90555
90556
90563
90564
90577
90578
90581
90582
90598
90599
90600
Page
SK12 Sloped channel - 39.37"
SK13 Sloped channel - 39.37"
SK14 Sloped channel - 39.37"
SK15 Sloped channel - 39.37"
SK16 Sloped channel - 39.37"
SK17 Sloped channel - 39.37"
SK18 Sloped channel - 39.37"
SK19 Sloped channel - 39.37"
SK020 Neutral channel - 39.37"
SK20 Sloped channel - 39.37"
SK21 Sloped channel - 39.37"
SK22 Sloped channel - 39.37"
SK23 Sloped channel - 39.37"
SK24 Sloped channel - 39.37"
SK25 Sloped channel - 39.37"
SK26 Sloped channel - 39.37"
SK27 Sloped channel - 39.37"
SK28 Sloped channel - 39.37"
SK29 Sloped channel - 39.37"
SK30 Sloped channel - 39.37"
SK030 Neutral channel - 39.37"
SK900 In-line catch basin - 19.69"
PowerLok hanger
CSK01 Neutral channel - 39.37"
CSK01-ADA Neutral channel - 39.37"
CSK1 Sloped channel - 39.37"
CSK1-ADA Sloped channel - 39.37"
CSK2 Sloped channel - 39.37"
CSK2-ADA Sloped channel - 39.37"
CSK3 Sloped channel - 39.37"
CSK3-ADA Sloped channel - 39.37"
CSK4 Sloped channel - 39.37"
CSK4-ADA Sloped channel - 39.37"
CSK5 Sloped channel - 39.37"
CSK5-ADA Sloped channel - 39.37"
CSK6 Sloped channel - 39.37"
CSK6-ADA Sloped channel - 39.37"
CSK7 Sloped channel - 39.37"
CSK7-ADA Sloped channel - 39.37"
CSK8 Sloped channel - 39.37"
CSK8-ADA Sloped channel - 39.37"
CSK9 Sloped channel - 39.37"
CSK9-ADA Sloped channel - 39.37"
CSK10 Sloped channel - 39.37"
CSK10-ADA Sloped channel - 39.37"
CSK010 Neutral channel - 39.37"
CSK010-ADA Neutral channel - 39.37"
CSK0103 Neutral channel - 19.69"
CSK0103-ADA Neutral channel - 19.69"
CSK11 Sloped channel - 39.37"
CSK12 Sloped channel - 39.37"
CSK11-ADA Sloped channel - 39.37"
CSK12-ADA Sloped channel - 39.37"
CSK13 Sloped channel - 39.37"
CSK13-ADA Sloped channel - 39.37"
CSK14 Sloped channel - 39.37"
CSK14-ADA Sloped channel - 39.37"
CSK15 Sloped channel - 39.37"
CSK15-ADA Sloped channel - 39.37"
CSK16 Sloped channel - 39.37"
CSK16-ADA Sloped channel - 39.37"
CSK17 Sloped channel - 39.37"
CSK17-ADA Sloped channel - 39.37"
CSK18 Sloped channel - 39.37"
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
54
95
95
95
95
95
95
95
97
95
95
95
95
95
97
95
95
95
95
95
95
95
95
95
95
95
95
95
95
95
95
95
95
95
95
95
95
95
95
95
95
95
Part # Description
90601
90619
90620
90626
90627
90634
90635
90642
90643
90654
90655
90666
90667
90678
90679
90683
90684
90691
90692
90707
90708
90715
90716
90729
90730
90731
90732
90743
90744
90792
90793
90815
90826
90839
90840
90847
90848
90852
90853
90854
90855
90857
91082
91083
91085
91087
91110
91113
91120
91393
91397
91404
91405
91412
91418
91423
91427
91435
91436
91437
91439
91442
91448
91450
Page
CSK18-ADA Sloped channel - 39.37" 95
95
CSK19 Sloped channel - 39.37"
CSK19-ADA Sloped channel - 39.37" 95
95
CSK20 Sloped channel - 39.37"
CSK20-ADA Sloped channel - 39.37" 95
95
CSK020 Neutral channel - 39.37"
CSK020-ADA Neutral channel - 39.37" 95
95
CSK21 Sloped channel - 39.37"
CSK21-ADA Sloped channel - 39.37" 95
95
CSK22 Sloped channel - 39.37"
CSK22-ADA Sloped channel - 39.37" 95
95
CSK23 Sloped channel - 39.37"
CSK23-ADA Sloped channel - 39.37" 95
95
CSK24 Sloped channel - 39.37"
CSK24-ADA Sloped channel - 39.37" 95
95
CSK25 Sloped channel - 39.37"
CSK25-ADA Sloped channel - 39.37" 95
95
CSK26 Sloped channel - 39.37"
CSK26-ADA Sloped channel - 39.37" 95
95
CSK27 Sloped channel - 39.37"
CSK27-ADA Sloped channel - 39.37" 95
95
CSK28 Sloped channel - 39.37"
CSK28-ADA Sloped channel - 39.37" 95
95
CSK29 Sloped channel - 39.37"
95
CSK30 Sloped channel - 39.37"
CSK29-ADA Sloped channel - 39.37" 95
CSK30-ADA Sloped channel - 39.37" 95
95
CSK030 Neutral channel - 39.37"
CSK030-ADA Neutral channel - 39.37" 95
CSK900 In-line catch basin - 19.69" 95
95
CSK900-ADA In-line catch basin
SK0203 Neutral channel - 19.69"
47
SK0303 Neutral channel - 19.69"
47
CSK0203 Neutral channel - 19.69"
95
CSK0203-ADA Neutral channel - 19.69" 95
CSK0303 Neutral channel - 19.69"
95
CSK0303-ADA Neutral channel - 19.69" 95
CSK204-6 6" inlet cap
95
CSK308-6 6" outlet cap
95
Foul air trap
54
CSK304-6 6" inlet cap
95
CSK208-6 6" outlet cap
95
C308-6 6" Outlet cap
91
C204-6 6" Inlet cap
91
C304-6 6" Inlet cap
91
C208-6 6" Outlet cap
91
Type 611 catch basin riser section
53
Type C611 catch basin riser section 53
ACO Seal flexible joint sealant
117
FF3/1 Sloped former - 8'
75
FF3/1 Sloped former - 8’ galv rail
75
FF3/2 Sloped former - 8’ galv rail
75
FF3/2 Sloped former - 8'
75
FF3/3 Sloped former - 8'
75
FF3/3 Sloped former - 8’ galv rail
75
FF3/4 Sloped former - 8’ galv rail
75
FF3/4 Sloped former - 8'
75
FF3/5 Sloped former - 8’ galv rail
75
FF3/5 Sloped former - 8'
75
FF3/05 Neutral former - 8’ galv rail
75
FF3/05 Neutral former - 8'
75
FF3/6 Sloped former - 8’ galv rail
75
FF3/6 Sloped former - 8'
75
FF3/7 Sloped former - 8'
75
www.acousa.com
Part # Description
91455
91463
91464
91473
91477
91481
91486
91492
91499
91504
91505
91513
91518
91521
91527
91536
91539
91541
91547
91552
91554
91563
91568
91572
91578
91584
91585
91591
91596
91603
91608
91614
91617
91695
91697
93190
93209
93217
93225
93233
93241
93250
93268
93276
93284
93292
93301
93313
93325
93337
93349
93408
93411
93441
93452
93488
93495
93496
93502
93503
93511
93512
93523
93524
Page
FF3/7 Sloped former - 8’ galv rail
FF3/8 Sloped former - 8’ galv rail
FF3/8 Sloped former - 8'
FF3/9 Sloped former - 8'
FF3/9 Sloped former - 8’ galv rail
FF3/10 Sloped former - 8'
FF3/10 Sloped former - 8’ galv rail
FF3/010 Neutral former - 8’ galv rail
FF3/010 Neutral former - 8'
FF3/11 Sloped former - 8'
FF3/11 Sloped former - 8’ galv rail
FF3/12 Sloped former - 8'
FF3/12 Sloped former - 8’ galv rail
FF3/13 Sloped former - 8’ galv rail
FF3/13 Sloped former - 8'
FF3/14 Sloped former - 8'
FF3/14 Sloped former - 8’ galv rail
FF3/15 Sloped former - 8'
FF3/15 Sloped former - 8’ galv rail
FF3/015 Neutral former - 8'
FF3/015 Neutral former - 8’ galv rail
FF3/16 Sloped former - 8'
FF3/16 Sloped former - 8’ galv rail
FF3/17 Sloped former - 8’ galv rail
FF3/17 Sloped former - 8'
FF3/18 Sloped former - 8'
FF3/18 Sloped former - 8’ galv rail
FF3/19 Sloped former - 8’ galv rail
FF3/19 Sloped former - 8'
FF3/20 Sloped former - 8’ galv rail
FF3/20 Sloped former - 8'
FF3/020 Neutral former - 8’ galv rail
FF3/020 Neutral former - 8'
FF3/900 catch basin - 12" x 24" galv rail
FF3/900 catch basin - 12" x 24"
F401 Sloped channel - 118"
F402 Sloped channel - 118"
F403 Sloped channel - 118"
F404 Sloped channel - 118"
F404N Neutral channel - 118"
F4045N Neutral channel - 39.37"
F405 Sloped channel - 118"
F406 Sloped channel - 118"
F407 Sloped channel - 118"
F407N Neutral channel - 118"
F4075N Neutral channel - 39.37"
F408 Sloped channel - 118"
F409 Sloped channel - 118"
F410 Sloped channel - 118"
F410N Neutral channel - 118"
F4105N Neutral channel - 39.37"
H100SK Neutral channel - 39.37"
H100SK ADA Neutral channel - 39.37"
CH100SK Neutral channel - 39.37"
CH100SK ADA Neutral channel - 39.37"
Strainer for 4" bottom outlets
SK3-01 Neutral channel - 39.37"
SK3-01 ADA Neutral channel - 39.37"
SK3-1 Sloped channel - 39.37"
SK3-1 ADA Sloped channel - 39.37"
SK3-2 Sloped channel - 39.37"
SK3-2 ADA Sloped channel - 39.37"
SK3-3 Sloped channel - 39.37"
SK3-3 ADA Sloped channel - 39.37"
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
63
83
83
97
97
54
51
51
51
51
51
51
51
51
125
Part Index
Part # Description
126
93534
93535
93546
93547
93552
93553
93563
93564
93578
93579
93585
93586
93597
93598
93601
93602
93610
93611
93629
93630
93633
93634
93644
93645
93657
93658
93668
93669
93670
93671
93681
93682
93693
93694
93706
93707
93718
93719
93725
93726
93734
93735
93741
93742
93750
93751
93766
93767
93779
93780
93782
93783
93793
93794
93805
93806
93814
93815
93820
93821
93837
93838
93881
93883
Page
SK3-4 Sloped channel - 39.37"
SK3-4 ADA Sloped channel - 39.37"
SK3-5 Sloped channel - 39.37"
SK3-5 ADA Sloped channel - 39.37"
SK3-6 Sloped channel - 39.37"
SK3-6 ADA Sloped channel - 39.37"
SK3-7 Sloped channel - 39.37"
SK3-7 ADA Sloped channel - 39.37"
SK3-8 Sloped channel - 39.37"
SK3-8 ADA Sloped channel - 39.37"
SK3-9 Sloped channel - 39.37"
SK3-9 ADA Sloped channel - 39.37"
SK3-10 Sloped channel - 39.37"
SK3-10 ADA Sloped channel - 39.37"
SK3-010 Neutral channel - 39.37"
SK3-010 ADA Neutral channel - 39.37"
SK3-11 Sloped channel - 39.37"
SK3-11 ADA Sloped channel - 39.37"
SK3-12 Sloped channel - 39.37"
SK3-12 ADA Sloped channel - 39.37"
SK3-13 Sloped channel - 39.37"
SK3-13 ADA Sloped channel - 39.37"
SK3-14 Sloped channel - 39.37"
SK3-14 ADA Sloped channel - 39.37"
SK3-15 Sloped channel - 39.37"
SK3-15 ADA Sloped channel - 39.37"
SK3-16 Sloped channel - 39.37"
SK3-16 ADA Sloped channel - 39.37"
SK3-17 Sloped channel - 39.37"
SK3-17 ADA Sloped channel - 39.37"
SK3-18 Sloped channel - 39.37"
SK3-18 ADA Sloped channel - 39.37"
SK3-19 Sloped channel - 39.37"
SK3-19 ADA Sloped channel - 39.37"
SK3-20 Sloped channel - 39.37"
SK3-20 ADA Sloped channel - 39.37"
SK3-020 Neutral channel - 39.37"
SK3-020 ADA Neutral channel - 39.37"
SK3-21 Sloped channel - 39.37"
SK3-21 ADA Sloped channel - 39.37"
SK3-22 Sloped channel - 39.37"
SK3-22 ADA Sloped channel - 39.37"
SK3-23 Sloped channel - 39.37"
SK3-23 ADA Sloped channel - 39.37"
SK3-24 Sloped channel - 39.37"
SK3-24 ADA Sloped channel - 39.37"
SK3-25 Sloped channel - 39.37"
SK3-25 ADA Sloped channel - 39.37"
SK3-26 Sloped channel - 39.37"
SK3-26 ADA Sloped channel - 39.37"
SK3-27 Sloped channel - 39.37"
SK3-27 ADA Sloped channel - 39.37"
SK3-28 Sloped channel - 39.37"
SK3-28 ADA Sloped channel - 39.37"
SK3-29 Sloped channel - 39.37"
SK3-29 ADA Sloped channel - 39.37"
SK3-30 Sloped channel - 39.37"
SK3-30 ADA Sloped channel - 39.37"
SK3-030 Neutral channel - 39.37"
SK3-030 ADA Neutral channel - 39.37"
SK3-0303 Neutral channel - 19.69"
SK3-0303 ADA Neutral channel - 19.69"
SK3-900 Catch basin top - 19.69"
SK3-900 ADA Catch basin top - 19.69"
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
Part # Description
93891
93893
93896
93899
93903
93905
94022
94039
94048
94057
94065
94076
94081
94096
94102
94114
94123
94130
94145
94156
94169
94178
94184
94191
94206
94210
94222
94237
94245
94259
94263
94271
94287
94296
94304
94318
94322
94330
94349
94351
94362
94376
94381
94388
94563
94568
94625
94626
94637
94638
94641
94643
94658
94660
94663
94666
94674
94676
94699
95063
95140
95165
95228
95232
Page
FG200 Stainless steel bar grate - 36" 67
FG200 Ductile iron ADA grate - 18"
67
FG200 Ductile iron slotted grate - 18" 67
FG200 Galv. steel bar grate - 36"
67
SK204-6 6" Inlet cap
47
SK304-6 6" Inlet cap
47
SK01 ADA Neutral channel - 39.37" 47
SK1 ADA Sloped channel - 39.37"
47
SK2 ADA Sloped channel - 39.37"
47
SK3 ADA Sloped channel - 39.37"
47
SK4 ADA Sloped channel - 39.37"
47
SK5 ADA Sloped channel - 39.37"
47
SK6 ADA Sloped channel - 39.37"
47
SK7 ADA Sloped channel - 39.37"
47
SK8 ADA Sloped channel - 39.37"
47
SK9 ADA Sloped channel - 39.37"
47
SK10 ADA Sloped channel - 39.37"
47
SK010 ADA Neutral channel - 39.37" 47
SK0103 ADA Neutral channel - 19.69" 47
SK11 ADA Sloped channel - 39.37"
47
SK12 ADA Sloped channel - 39.37"
47
SK13 ADA Sloped channel - 39.37"
47
SK14 ADA Sloped channel - 39.37"
47
SK15 ADA Sloped channel - 39.37"
47
SK16 ADA Sloped channel - 39.37"
47
SK17 ADA Sloped channel - 39.37"
47
SK18 ADA Sloped channel - 39.37"
47
SK19 ADA Sloped channel - 39.37"
47
SK20 ADA Sloped channel - 39.37"
47
SK020 ADA Neutral channel - 39.37" 47
SK0203 ADA Neutral channel - 19.69" 47
SK21 ADA Sloped channel - 39.37"
47
SK22 ADA Sloped channel - 39.37"
47
SK23 ADA Sloped channel - 39.37"
47
SK24 ADA Sloped channel - 39.37"
47
SK25 ADA Sloped channel - 39.37"
47
SK26 ADA Sloped channel - 39.37"
47
SK27 ADA Sloped channel - 39.37"
47
SK28 ADA Sloped channel - 39.37"
47
SK29 ADA Sloped channel - 39.37"
47
SK30 ADA Sloped channel - 39.37"
47
SK030 ADA Neutral channel - 39.37" 47
SK900 ADA In-line catch basin - 19.69" 47
SK0303 ADA Neutral channel - 19.69" 47
FF600 Galv steel end frame
75
FF600 Black coated steel end frame 75
Type 620 catch basin assembly (short)
53
Type 620ADA catch basin assembly (short) 53
Type 630 catch basin assembly (deep)
53
Type 630ADA catch basin assembly (deep) 53
Type C620 catch basin assembly (short) 53
Type C620ADA catch basin assembly (short) 53
Type C630 catch basin assembly (deep) 53
Type C630ADA catch basin assembly (deep) 53
Type 610 top section with ADA grate
53
Type 610 top section with slotted grate
53
Type C610 top section with slotted grate 53
Type C610 top section with ADA grate
53
Galvanized steel perforated grate
105
Universal closing/4" inlet/outlet cap 47
Type 824 6" Sch. 40 oval-to-round outlet 54
Stainless steel perforated grate
105
Black coated steel frame - 39.37"
63
Galvanized steel frame - 39.37"
63
www.acousa.com
Part # Description
95243
95360
95365
95373
95374
95375
95379
95395
95403
95460
95537
95545
95553
96484
96495
96504
96739
96740
96752
96764
96788
96825
96877
96882
96903
96905
96913
96918
96924
96926
96928
96932
96931
96933
96935
96937
97048
97052
97066
97079
97087
97116
97126
97139
97148
97153
97162
97174
97188
97197
97203
97212
97229
97231
97334
97385
97393
97425
97438
97442
97443
97443
97444
97449
Page
Stainless steel frame - 39.37"
63
H100K Neutral channel - 39.37"
83
H80K Neutral channel - 39.37"
83
H80KS Neutral channel - 39.37"
83
CH100K Neutral channel - 39.37"
97
CH80K Neutral channel - 39.37"
97
H100KS Neutral channel - 39.37"
83
MiniKlassik galv. steel closing cap
105
MiniKlassik stainless closing cap
105
Assembly tape - roll
75
Galv steel slotted grate 39.37"
105
Stainless steel slotted grate 39.37" 105
Ductile slotted grate 19.69"
105
CK900 In-line catch basin - 19.69"
93
KS900 In-line catch basin - 19.69"
35
K900 In-line catch basin - 19.69"
33
H100K Galvanized steel closing cap 83
H100KS Stainless steel closing cap 83
Type 461Q - ductile iron slotted grate 39
Type 445Q - stainless steel ADA grate 36
Plastic mosaic grate 19.69"
105
Universal closing/4" inlet/outlet cap 33
Brickslot access unit - 19.69"
98
Type 446Q - stainless ADA grate
36
Membrane subframe - galv rail
103
Membrane clamping device galv steel 103
Membrane clamping device stainless 103
Membrane subframe - stainless rail 103
Curb outlet - Type 6
107
Roll curb outlet - ADA grate
107
Roll curb outlet - slotted grate
107
Pipe inlet
107
Roll curb outlet with pipe inlet - slotted 107
Roll curb outlet with pipe inlet - ADA 107
Type 440 - fiberglass grid grate
37
Type 441 - fiberglass grid grate
37
SK208-6 6" Outlet cap
47
SK308-6 6" Outlet cap
47
Black coated steel frame - 108"
67
Galvanized steel frame - 108"
67
Stainless steel frame - 108"
67
Type 479Q - ductile iron mosaic grate 38
K304-6 6" inlet cap
33
KS304-6 6" inlet cap
35
CK304-6 6" inlet cap
93
K204-6 6" inlet cap
33
KS204-6 6" inlet cap
35
CK204-6 6" inlet cap
93
K308-6 6" outlet cap
33
KS308-6 6" outlet cap
35
CK308-6 6" outlet cap
93
K208-6 6" outlet cap
33
KS208-6 6" outlet cap
35
CK208-6 6" outlet cap
93
H100SK Closing cap
83
Type 495Q - grey plastic ADA grate 37
Type 494Q - black plastic ADA grate 37
4" Pipe plain end adapter
69
6" Pipe plain end adapter
69
F660 Class C stainless bar grate
69
F660 Class C galv steel bar grate
69
FF300 Galvanized steel bar grate
75
8" Pipe plain end adapter
69
F660 Class E ductile iron grate
69
ACO DRAIN
Part # Description
97449
97452
97452
97453
97453
97455
97464
97475
97995
98008
98013
98021
98034
98048
98059
98067
98069
98075
98103
98132
98163
98167
98171
98195
98254
98255
98282
98284
98361
98363
98365
98372
98373
98375
98381
98382
98386
98397
98403
98406
98407
98462
98471
98487
98524
98538
98545
98567
98572
98581
98593
98597
98603
98604
98605
98607
98653
98665
98683
98695
98707
98714
98717
98731
Page
FF300 Ductile iron slotted grate
75
F880 Class C galv steel bar grate
69
FF600 Galvanized steel bar grate
77
F880 Class E ductile iron grate
69
FF600 Ductile iron slotted grate
77
F880 Class C stainless bar grate
69
FF300 Galvanized steel bar grate
75
Hanging bracket
54
F660 Black coated steel frame
69
F660 Galvanized steel frame
69
F660 Stainless steel frame
69
F880 Black coated steel frame
69
F880 Galvanized steel frame
69
F880 Stainless steel frame
69
F880 Plastic trash bucket
69
F660 Plastic trash bucket
69
F660 Catch basin - 24" x 12"
69
F880 Catch basin - 24" x 24"
69
FG200 Vertical outlet adapter
67
SK3-306 Closing/outlet end cap
51
F900 Channel/catch basin collar
63
FG100 Channel/catch basin adapter 69
FG200 Channel/catch basin adapter 69
Vertical outlet adapter
63
FastForm catch basin - 24"x24" galv rail 75
FastForm catch basin - 24" x 24"
77
FF600 Steel end frame
77
Black coated steel end frame
77
FG200 Outlet cap (M) black frame
67
FG200 Closing cap (M) black frame 67
FG200 Closing cap (F) black frame
67
FG200 Closing cap (M) stainless frame 67
FG200 Outlet cap (M) stainless frame 67
FG200 Closing cap (F) stainless frame 67
FG200 Outlet cap (M) galv steel frame 67
FG200 Closing cap (M) galv steel frame 67
FG200 Closing cap (F) galv steel end 67
F900 Black coated steel catch basin frame 63
F900 Stainless steel catch basin frame
63
F900 Galvanized steel catch basin frame
63
F900 In-line catch basin - 19.69"
63
H80K Galvanized steel closing cap
83
H80KS Stainless steel closing cap
83
Type 600 Filter bag
53
Black coated steel frame - 36"
67
Galvanized steel frame - 36"
67
Stainless steel frame - 36"
67
Black coated steel frame - 118"
63
Galvanized steel frame - 118"
63
Stainless steel frame - 118"
63
Closing cap with black end frame
63
Closing/outlet cap - black frame
63
Closing/outlet cap - galv steel frame 63
Closing cap - galv steel frame
63
Closing cap - stainless frame
63
Closing/outlet cap - stainless frame 63
600 Series plastic trash bucket - short 53
600 Series plastic trash bucket - deep 53
Type 430Q - stainless steel mesh grate 38
Type 431Q - stainless steel mesh grate 38
Type 405Q - galv steel mesh grate
38
Type 406Q - galv steel mesh grate
38
K900 QuickLok bar (removable)
33
FF6/4 Sloped former - 8'
77
Part # Description
98732
98733
98734
98735
98736
98737
98739
98741
98742
98743
98744
98745
98746
98747
98748
98751
98752
98753
98754
98756
98757
98758
98759
98761
98762
98763
98764
98765
98767
98768
98769
98771
98773
98774
98775
98776
98777
98778
98779
98782
98783
98784
98785
98786
98787
98788
98789
98854
98866
98879
98883
98892
98905
98918
98927
98934
98946
98951
98988
98999
99006
99013
99021
99034
Page
FF6/1 Sloped former - 8’ galv rail
FF6/2 Sloped former - 8'
FF6/3 Sloped former - 8’ galv rail
FF6/2 Sloped former - 8’ galv rail
FF6/1 Sloped former - 8'
FF6/3 Sloped former - 8'
FF6/4 Sloped former - 8’ galv rail
FF6/05 Neutral former - 8’ galv rail
FF6/7 Sloped former - 8'
FF6/5 Sloped former - 8'
FF6/6 Sloped former - 8’ galv rail
FF6/05 Neutral former - 8'
FF6/5 Sloped former - 8’ galv rail
FF6/7 Sloped former - 8’ galv rail
FF6/6 Sloped former - 8'
FF6/8 Sloped former - 8’ galv rail
FF6/8 Sloped former - 8'
FF6/10 Sloped former - 8’ galv rail
FF6/10 Sloped former - 8'
FF6/9 Sloped former - 8'
FF6/010 Neutral former - 8’ galv rail
FF6/9 Sloped former - 8’ galv rail
FF6/010 Neutral former - 8'
FF6/11 Sloped former - 8'
FF6/13 Sloped former - 8’ galv rail
FF6/11 Sloped former - 8’ galv rail
FF6/13 Sloped former - 8'
FF6/12 Sloped former - 8'
FF6/14 Sloped former - 8’ galv rail
FF6/14 Sloped former - 8'
FF6/12 Sloped former - 8’ galv rail
FF6/17 Sloped former - 8’ galv rail
FF6/015 Neutral former - 8'
FF6/16 Sloped former - 8’ galv rail
FF6/15 Sloped former - 8'
FF6/015 Neutral former - 8’ galv rail
FF6/16 Sloped former - 8'
FF6/15 Sloped former - 8’ galv rail
FF6/17 Sloped former - 8'
FF6/18 Sloped former - 8’ galv rail
FF6/20 Sloped former - 8'
FF6/19 Sloped former - 8'
FF6/20 Sloped former - 8’ galv rail
FF6/020 Neutral former - 8’ galv rail
FF6/19 Sloped former - 8’ galv rail
FF6/18 Sloped former - 8'
FF6/020 Neutral former - 8'
Type 477Q - ductile iron grid grate
Type 410Q - galv. steel perforated grate
Type 412Q - galv. steel perforated grate
Type 451Q - stainless perforated grate
Type 453Q - stainless perforated grate
Type 411Q - galv. steel perforated grate
Type 413Q - galv. steel perforated grate
Type 465Q - stainless perforated grate
Type 466Q - stainless perforated grate
Type 485Q - brass perforated grate
Type 486Q - brass perforated grate
Brickslot - 19.69"
Brickslot - 39.37"
F801 Sloped channel - 108"
F802 Sloped channel - 108"
F803 Sloped channel - 108"
F803N3 Neutral channel - 36"
www.acousa.com
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
77
39
36
36
36
36
38
38
38
38
38
38
98
98
67
67
67
67
Part # Description
99048
99055
99062
99071
99084
99095
99109
99116
99123
99132
99145
99156
99162
99175
99186
99192
99272
99281
99295
99304
99317
99328
99362
99374
99388
99399
99404
99415
99453
99462
99469
99478
99489
99503
F803N Neutral channel - 108"
F804 Sloped channel - 108"
F805 Sloped channel - 108"
F806 Sloped channel - 108"
F806N3 Neutral channel - 36"
F806N Neutral channel - 108"
F807 Sloped channel - 108"
F808 Sloped channel - 108"
F809 Sloped channel - 108"
F809N3 Neutral channel - 36"
F809N Neutral channel - 108"
F810 Sloped channel - 108"
F811 Sloped channel - 108"
F812 Sloped channel - 108"
F812N3 Neutral channel - 36"
F812N Neutral channel - 108"
K010 Neutral channel - 39.37"
K0103 Neutral channel - 19.69"
K020 Neutral channel - 39.37"
K0203 Neutral channel - 19.69"
K030 Neutral channel - 39.37"
K0303 Neutral channel - 19.69"
KS010 Neutral channel - 39.37"
KS0103 Neutral channel - 19.69"
KS020 Neutral channel - 39.37"
KS0203 Neutral channel - 19.69"
KS030 Neutral channel - 39.37"
KS0303 Neutral channel - 19.69"
CK010 Neutral channel - 39.37"
CK0103 Neutral channel - 19.69"
CK030 Neutral channel - 39.37"
CK020 Neutral channel - 39.37"
CK0203 Neutral channel - 19.69"
CK0303 Neutral channel - 19.69"
Page
67
67
67
67
67
67
67
67
67
67
67
67
67
67
67
67
33
33
33
33
33
33
35
35
35
35
35
35
93
93
93
93
93
93
127
Other ACO product lines
ACO SPORT
ACO Sport is a range of surface
drainage and building accessories for
track & field, used at Olympic sites
since 1972.
AQUADUCT
Aquaduct custom designs and
manufactures fiberglass trench drain
systems to meet individual project
requirements.
ACO ROAD
ACO Road is a range of surface
drainage products engineered for
the unique design and performance
demands of highways, urban roads
and bridges.
ACO ENVIRONMENT
ACO Environment is a range of
separator and spill containment
systems manufactured in corrosion
resistant polymer concrete.
ACO WILDLIFE
ACO Wildlife is a tunnel and fence
system designed to guide amphibians
and other small creatures safely
across roads.
ACO HOME
ACO Home is a complete range of
simple plastic and polymer concrete
trench units for use around the
home, garden and office.
128
ACO Polymer Products, Inc.
East Sales Office
P.O. Box 245
Chardon, OH 44024
Tel: (440) 285-7000
Toll free: (800) 543-4764
Fax: (440) 285-7005
West Sales Office
PO Box 12067
Casa Grande, AZ 85230
Tel: (520) 421-9988
Toll Free: (888) 490-9552
Fax: (520) 421-9899
Electronic Contact:
[email protected]
www.acousa.com
© October 2008 PDF ACO Polymer Products, Inc.
All reasonable care has been taken in compiling the information in this document. All recommendations and suggestions on the use of ACO products are made without
guarantee since the conditions of use are beyond the control of the Company. It is the customer’s responsibility to ensure that each product is fit for its intended purpose
and that the actual conditions of use are suitable. ACO Polymer Products, Inc. reserves the right to change products and specifications without notice.
Re-order Part # DL099
www.acousa.com