Download Report

Sheetmetal
Proudly Distributed By
SHEETMETAL
19652
26146
Front Fenders for Wide Glide
and Softail Models
Custom Fender for Wide Glide
Front Ends
A bolt-on version that completely replaces
the stock front fender on Dyna Wide Glide,
Softail and 4-speed FXWG models from 80-06
(except Heritage Softail, Fat Boy and Springer
Softail models). Styled with an added accent
bead around its entire edge. These fenders
include polished aluminum spacer blocks, and
fit with 19" or 21" wheels only.
13183
6" wide��$139.99
Fenders for Narrow Glide
Models
Original-style front fenders for FX, FXR,
Sportster and Dyna Glide models from
73-03. Available in a stock replacement
version or with the front tip cut back for a
trimmer look. Both fenders are unpainted
and include chrome brackets and the rivets
necessary to install them.
19652
Fender (repl. OEMs 59007-73TB,
59111-74)��$61.99
A trim, tire-hugging fender with chrome
brackets, ready-to-paint. A reproduction
of the Original Equipment front fender on
FXST, FXSTC and 4-speed FXWG models from
80-07 and Dyna Wide Glide models 80-05.
26146
Replaces OEM 59924-80��$42.99
26350
Same as CC #26146 except with
raw steel mounting bracket�� $39.99
Wide Glide Front Fender for
35mm Forks
Custom front fender for the 35mm front
forks on FX, FXR and Sportster models from
73-E87. Unpainted, and complete with
integral chrome-plated brackets. For use
with 18", 19" or 21" wheels.
26163
Replaces OEM 59031-83��$45.99
Narrow Front Fenders
Springer Front Fender for Big
Twins
Custom Skirted Fender with Flip
Based loosely on the skirted early K model
front fender, this timeless classic has been
updated to fit all 35mm and 39mm front
forks from 73-13.
13196
Unpainted (5 3/4" wide) ��$112.99
Accurate, faithful reproduction of the
original fender. Complete with braces and
fender edge ‘reveal’. Fits all Big Twins from
37-48.
26520
Replaces OEM 59000-36 (measures 7
1/2"-wide)��$109.99
These replacement narrow front fenders fit
FX, FXR, Sportster and Dyna Glide models
from 73-99 with 35mm or 39mm front forks.
Available chrome or unpainted with chrome
brackets. For use with narrow 18", 19" and
21" rims.
240331 Chrome fender and bracket �� $49.99
240383 Unpainted fender and bracket
(replaces OEM 59031-83) ��$31.99
Note: Fender should not be used on bikes equipped with
highway bars.
Narrow Front Fender for FL
Models
Front Fender for Early ‘Touring’ Models
A precisely-crafted reproduction of the 54-84 4-speed ‘Dresser’ front fender with properly
rolled edges and structural reinforcement. Will also fit Touring models from 80-13.
13193
Unpainted steel�� $109.99
SHEET.02
*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.
Custom, unpainted steel narrow FXWG-style
front fender for all 4-speed FL model forks
from 49-84. Includes chrome mounting
brackets, the fender profile is designed to
clear 18", 19" and 21" tires.
26159
Unpainted (7 3/4"-wide) ��$52.99
Please see Cautionary Information in back of catalog.
SHEETMETAL
Front Fenders for 4-Speed Models
Our replacement steel fenders fit all 4-speed FL models from 81-84,
and have all of the correct holes and dimples for fender trim and tip
lights.
240380 81-84 style (replaces OEM 59093-79) ��$99.99
Hooded Skull Fender Ornament
• Chrome with a satin black hood
• Universal mount will fit most front fenders
• Includes a rubber mounting gasket and hardware (requires
drilling fender for installation)
621124 Hooded skull fender ornament, sold each ��$27.99
Chrome Lower Fender Trim
A reproduction of the lower trim installed on FL models from 68-75,
but completely chrome-plated without the black accents. Fits all FL,
FLT, FLHT and FLHS models from 49-85. Comes complete with chrome
mounting hardware.
26585
Replaces OEM 59233-68��$19.99
Skull Head Fender Trim
26589
Quality die-cast trim piece is contoured to match the front fender
on FL, FLT, FLHT models 80-13 and many custom applications.
Features a highly detailed skull head logo with gold trim and 12
volt illuminated eyes.
240078Chrome with gold trim and illuminated eyes ��$53.99
26588
240071
Vintage ‘V’ Style Fender Tips and Trim
Reproductions of the chrome front and rear fender tips and stainless
steel trim pieces. The fender tips are die-cast in the ‘V’ design used
as Original Equipment from 59-66. The front fender side trim and
front fender lower edge trim are formed in stainless steel. Each part
includes hardware, and fits all FL front fenders from 49-86 and all FL
rear fenders from 58-86.
26586
Front fender trim set (includes CC #’s 26588 and 26595)�� $29.99
26588
Front fender tip ‘V’ design (indexed for side spears) as used
from 59-66 (repl. OEM 59216-59) �� $19.99
26595
Front fender side spear set as used from 57-73 (repl. OEMs
59205-57 and 59206-57)�� $16.99
26589
Rear fender tip ‘V’ design as used from 59-66 (repl. OEM
59887-59)�� $19.99
Eagle Head Fender Ornament
This die-cast fender ornament is highly detailed and come with
illuminated eyes. The illuminated version is internally lit with 2
independent 12V light bulbs which can be connected to the turn
signals or running lights. Fits FL, FLT and FLHT models 80-13 and
many custom applications.
240071 Illuminated eyes with gold accented beak��$24.99
27824
Replacement bulb, 12V 2W (box of 10)��$0.60
w w w.cu sto m c h ro m e.co m
SHEET.03
SHEETMETAL
Quickbob Rear Fender
for FX Models
Hinged Rear Fenders for FL Swingarms
These two-piece hinged fenders fit all 4-speed Big Twin FL frames
from 58-84. They also fit FX models if FL struts are used and can be
adapted to FXWGs. A slight dent must be made in the front right
lower corner of the fender to clear the FXE battery box. Unpainted
steel.
13186
With no taillight mount (repl. OEM 59604-65A)��$109.99
Custom rear fender for an
easy, affordable conversion
to the Fat Bob look. Fits stock
4-speed FX frames and uses the stock width fender struts. Cannot
be used as a replacement fender for FXWGs. Heavy-gauge metal for
lasting service.
13188
Fits FX models from 73-85 (except FXWG, FXST)��$89.99
Custom Fat Bob Rear
Fenders
Original style universal and custom
application fenders. Available with
left or right-hand chain cutaway
without taillight mount. Fenders
measure approx. 38"-long, 7"-wide and 5 1/2"-deep. Fenders are
unpainted.
Left Chain Cutaway
Fits all Big Twin models and bikes with the chain on the left side.
13178
Without taillight mount ��$74.99
One-Piece Rear Fenders for FL Models
Accurate reproductions of the one-piece rear fenders on 4-speed FL
models from 80-84. One version is smooth with no taillight or turn
signal mounts, and the other has the 73-98 taillight mount (but no
turn signal mounts). Fender strut mounting holes are already drilled.
13189
With no taillight mount��$114.99
13212
With 73-98 taillight mount but no indentations for the turn
signal mounting bar��$119.99
Right Chain Cutaway
Fits Sportster models in custom frames and bikes with the chain on
the right side.
13179
Without taillight mount ��$75.99
Fat Bob
Fender and
Taillight
Kit for FXR
Models
• Custom Fat Bob styling
• 3-piece kit includes Fat Bob fender, Fat Bob taillight and deluxe
taillight bracket
• Features flush-mount taillight positioning
• Bolts easily to all stock fender struts
• Compatible with Original Equipment and CC sissy bar kits
13250
Fits all FXR models from 82-94��$179.99
25933
25932
25931
Rear Fenders for FX Models
Detailed reproductions of the Original Equipment 4-speed FX rear
fenders from 73-85. Available with or without mounting bracket for
73-98 taillight assembly.
25931
Original style with light mount ��$69.99
25932
Original style without mount��$65.99
25933
Custom bobbed��$74.99
Note: Taillight, visor and license mounting bracket are not included and are shown for illustration purposes only.
SHEET.04
*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.
Rear Fender for FXR Models
Stock replacement rear fender for FXR
models from 82-99 (except FXRT models).
Unpainted steel.
240425 Replaces OEM 59634-81A ��$74.99
Please see Cautionary Information in back of catalog.
SHEETMETAL
13208
13209
Sport Bob Rear Fender Kits for Sportster Models
These exclusive fender kits include a new ABS plastic fender
extension for the front of the fender, a Cateye taillight assembly
with mounting bracket and the extra pop rivets necessary to reinstall
your circuit breaker clips. They looks great when combined with the
CC #25576 one-piece Sport Bob gas tanks found elsewhere in this
catalog section.
13209
Fits Sportster models from 94-03�� $164.99
13208
Fits Sportster models from 82-93�� $135.99
Rigid Rear Fender
A replacement rear fender for rigid frame Big Twins from 49-57.
Includes braces and has holes drilled for the seat clip. Rear section is
not drilled to permit choice of taillamp.
26524
Replaces OEM 59612-41�� $149.99
Rigid Rear Fender for 45s
An accurate reproduction of the rigid rear fender. Perfect in every
detail and comes complete with brackets ready to bolt on.
13191
Fits 37-46 45" Twins��$164.99
Rigid Rear Fender for Big Twins
An accurate reproduction of the rigid rear fender used on 36-48
overhead valve Big Twins. Perfect in detail and complete with
brackets ready to bolt-on. Unpainted.
13187
Replaces OEM 59604-39�� $169.99
w w w.cu sto m c h ro m e.co m
SHEET.05
SHEETMETAL
13530
13531
Wide Fenders for Rigid Frames
Custom flat fenders made of heavy-duty 14-gauge steel in wide
widths to cover that really big rubber.
95073
7 1/2"-wide��$29.99
95074
8 1/2"-wide��$35.99
950759"-wide ��$38.99
12459
’OneTonHo’ and ’TwoTonHo’ Custom Rear Fenders
12457
Universal Steel Rear Fenders and Supports
Fenders
Available in 5" or 6" widths. Great for trailers too.
12457
5" wide��$29.99
12459
6" wide��$39.99
Designed specifically for wide rigid frames. Fenders feature internal
wiring loom and a belt cutout. The ‘TwoTonHo’ has built-in fender
supports pre-drilled for turn signals while the ‘OneTonHo’ has no
supports.
13530
9"-wide ‘TwoTonHo’��$149.99
13531
9"-wide ‘OneTonHo’��$139.99
13526
8 1/2"-wide ‘OneTonHo’ ��$139.99
13520
7 1/2"-wide ‘OneTonHo’ ��$139.99
For Santee 200-Series Rigid Frames
08680
9"-wide custom ‘OneTonHo’��$149.99
Billet ‘Machine Gun’
Fender Struts by
Vulcan Engineering
13377
Custom Rear Fenders for Santee Rigid Frames
Plain steel straps support the rear fender on your wide-tired Santeeframed chopper.
For Santee 180-Series Rigid Frames
13377
8 1/2"-wide rear fender with plain steel strap supports ��$139.99
16955
8 1/2"-wide without support ��$149.99
Here is a cool set of fender
struts to help you mount
that rear fender on your
latest project. They are
CNC-Machined from billet
aluminum and then chromeplated. Fender struts measure
10 5/8” from mounting holes
center to center.
668254 Chrome Billet
‘Machine Gun’ Rigid
Fender Struts, Sold
as a pair �� $129.99
For Santee 200-Series Rigid Frames
16956
9"-wide without support��$149.99
SHEET.06
*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.
Please see Cautionary Information in back of catalog.
SHEETMETAL
26517
26518
Steel “Petcock Bungs” by Johnny’s Custom Shop
26522
Chrome Fender Strut Sets
Chrome rear fender struts for 4-speed Big Twin, Sportster and K
models from 54-86. All sets are formed from high-grade steel and
pre-drilled with the correct mounting holes before polishing and
plating. Can be used to mount custom, reproduction or Original
Equipment fenders.
Note: Hardware is not included, but is available as listed below.
26517
26518
78315
78319
26522
Fit FX models from 72-85 – 2 holes (not countersunk)��$79.99
Fit FL models from 58-84��$79.99
Fit FL models from 58-84 (turn signal holes have been
removed)��$70.99
Fit FXWG from 80-86 (turn signal holes have been removed)
��$73.99
While you’re creating that out of sight one-off tank, don’t forget
you need to get the gas to the engine, and that calls for a petcock
mount. Most petcocks used in custom applications, and what we
offer, have either 3/8” NPT or 1/4” NPT threads. These steel Petcock
Bungs are offered to accept either thread size. They are 2” long,
with 1/2” of either 3/8” NPT or 1/4” NPT internal thread for your
petcock to screw into, then the remaining 1 1/2” bored out to
.8200 inner bore to allow good gas flow. Can be used with custom
oil tanks as well. Comes Raw. Position Petcock Bung where you
want the petcock to mount, cut a hole in the tank, then weld ‘er
in!. Sold Each.
632705 Petcock Bung. 2” long, 7/8” O.D. For 3/8 NPT Petcocks�$15.99
632706 Petcock Bung. 2” long, 7/8” O.D. For 1/4 NPT Petcocks$15.99
632252 1/4” NPT Petcock. No reserve. (see petcocks) ��$27.99
632253 1/4” NPT Petcock. With reserve. (see petcocks) ��$45.99
12726
Fits OEM and custom tanks thru 74 with internal 3/8" NPT
connection (repl. OEM 62125-55B) ��$15.99
12727
3/8” NPT Petcock w/90 degree outlet. With reserve. (see
petcocks) ��$15.99
Fit Sportster and K models from 54-78 (turn signal holes have
been removed)��$79.99
Chrome Fender Struts for Sportster Models
Chrome-plated die-cast aluminum replacements for the Original
Equipment parts. Fit 4-speed Sportster models from 82-89 (replaces
OEMs 59950-81 and 59951-81).
78055
Fits 82-89 XL models. Sold in sets��$84.99
Rigid Frame Fender Struts
These cool looking fender struts are made
of chrome plated billet and measure 9 1/4”
from mounting holes center-to-center (10”
overall length). A great looking fender strut
set at an affordable price! Made in USA by
Motorway. Sold as pair.
632008 Rigid Frame Fender Struts��$139.99
Steel “Round Bungs” and “Round Nuts” by
Johnny’s Custom Shop
These Round Nuts are CNC machined for use as Sissy Bar
mounts, Fender mounts, Gas Tank mounts and a hundred other
applications. Paint, Chrome or Powder-coat as desired. Every
person putting a bike, or a street rod together needs a selection
of these handy puppies on their workbench! Use along with the
“Round Bungs” for allen head bolts also available in this catalog.
Sold in Pairs.
632701 Round Bung: 1/2” long, 1/2” O.D., 1/4” I.D. For 1/4” socket
allen head bolts��$9.99
632702 Round Bung: 5/8” long, 1/2” O.D., 5/16” I.D. For 5/16” socket
allen head bolts��$9.99
632703 Round Bung: 3/4” long, 11/16” O.D., 3/8” I.D. For 3/8” socket
allen head bolts��$9.99
632704 Round Bung: 7/8” long, 7/8” O.D., 7/16” I.D. For 7/16” socket
allen head bolts��$9.99
632693 Round Nut 1/4-20 UNC x 1/2��$9.99
632694 Round Nut 1/4-20 UNC x 1��$9.99
632695 Round Nut 5/16-18 UNC x 1/2��$9.99
632696 Round Nut 5/16-18 UNC x 1��$10.99
632697 Round Nut 3/8-16 UNC x 1/2 ��$9.99
632698 Round Nut 3/8-16 UNC x 1��$11.99
632699 Round Nut 7/16-14 UNC x 1/2��$9.99
632700 Round Nut 7/16-14 UNC x 1��$11.99
w w w.cu sto m c h ro m e.co m
SHEET.07
SHEETMETAL
19639
Universal Mounting Bracket/Gusset by Vulcan
Engineering
Milled from 1018 CF Steel, Not stamped! 3/16” Thick with a 3/8”
hole. Perfect for mounting custom exhaust or as a brake anchor
mount or any other applications you can come up with. Made in the
U.S.A.. Sold each.
668256 Universal bracket/gusset 3/16” thick w/ a 3/8” hole, sold each
��$8.99
650246
K&N Reinforced Rubber
Fender Washers
1"-diameter round rubber washers
have dozens of uses, in addition to the
obvious. Allows clean scratch-free, wellcushioned installations. Card of 12 packs
of 10.
22170
Fender washers ��$6.17
‘King’ Tanks for Early Sportster Models
2"-wider than the ‘Standard’ tank... enough to give extra mileage
and just wide enough to make them look great. These high tunnel
tanks are equipped with stock mounts but do not include mounting
hardware. They have a 3.1 gallon capacity. 3/8"NPT.
19639
Fits all models from 55-78��$134.99
25574
Fits all models from 79-81��$119.99
650246 Fits all models from 82-92��$119.99
3.5 Gallon Hand Shift Gas Tanks
Two versions of the obsolete hand shift style 3.5 gallon gas tank
sets. Accurate placement of the shifter gate lugs and shut-off rod
hole centers ensures trouble-free service. Available in two versions.
One is a totally accurate reproduction of the original, rod-style gas
shut-off equipped tank used from 48-65. The other is based on the
same tank, but eliminates the early style gas shut-off rod system and
replaces it with the tank bottom fitting for the late 13/16" externalthread petcock. Both tanks accept the correct cam-style gas caps and
are designed to accept the stock shifter guide.
25568
Original style with rod shut-off (shown)��$219.99
25569
Updated style for 75-07 petcock ��$219.99
‘Peanut’ Tank for Sportster Models
A quality reproduction of the Original Equipment 2.4 gallon gas tank.
12724
Fits early Sportster and K models from 55-78 (replaces OEM
61006-63B) ��$89.99
Note: All fuel tanks should be test fitted, pressure tested, and pre-sealed before painting.
Note: Fuel tanks, particularly where custom paint is planned, must be pressure tested and sealed with CCI tank sealer 670675 before painting to protect the final finish and prevent internal rust.
SHEET.08
*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.
Please see Cautionary Information in back of catalog.
SHEETMETAL
600154
Custom Chrome Custom “Low Tunnel” Gas Tank
This 2.8 gallon custom tank features a 1 1/2"-high tunnel with
universal style mounts for custom applications. Accepts 3/8" NPT
threaded petcock. Tank measures 15 1/2"-long x 9"-wide x 7"-high
with a 1 1/2" tunnel.
260121 Unpainted steel��$99.99
Note: All fuel tanks should be test fitted, pressure tested, and pre-sealed before painting.
600155
632933
600157
651261
Custom ‘Bobber Style Gas Tanks’ by Cole Foster
An absolutely beautiful new tank designed with the keen styling of
Cole Foster - Salinas Boyz Customs. The tanks feature a mini popup gas cap, and a unique raised tapered bead down the center of
the tank. Each tank has been designed to fit to stock frames but
can also be easily adapted to any custom application. They use
the existing stock rubber mounts or are included as needed. Fuel
capacity is 2.35 gallons.
600155 Fits Evolution Softail models from 84-99 and 4-speed FX and FL
models ��$260.99
Note: These applications require the front frame dash mount to be cut off and rear screw
hole modified.
600157
600154
Fits carburated Twin Cam 88 Softail models from 00-06 ��$260.99
Fits Sportster models from 82-03��$260.99
XL Flat Bottom Standard & King Sportster Tanks
by Paughco
Traditional Sportster Standard & King tanks. but modified for
universal applications with horseshoe front mounts and tab rear
mounts. They are equipped with a bung to accept late model 22mm
petcocks and screw-in style gas caps. Made in the U.S.A.
632933 XL Flat Bottom Gas Tank. 2.9 gals.��$179.99
651448 XL 95-03 Flat Bottom King Tank 2.9 gallon��$179.99
651449 XL 04-06 Flat Bottom King Tank 2.9 gallon��$219.99
651261 XL Flat Bottom Gas Standard Tank. 2.2-gallon ��$180.99
Replacement Gas Caps
47775
Stainless Steel (sold each) ��$42.99
47777
Chrome (sold each)��$42.99
w w w.cu sto m c h ro m e.co m
SHEET.09
SHEETMETAL
651285
651260
Custom Narrow Axed style Gas Tank by Paughco
This tank features a low tunnel with straight mounting tabs on both
the front and rear, single early cam style gas cap with dual threaded
1/4” fuel outlets. Made in the U.S.A.
651285 2.2 gallon Axed Harley-Style Custom tank with single gas cap
651259
��$171.99
670800
Indian Larry ‘Dished’ Tanks
The same tanks used on the Indian Larry bike in the build-off series.
Old School looks with modern production techniques bring you the
cool style you want at an affordable price. Easy mounting by drilling
of the backbone and can be adapted to many styles of stock and
custom frames.
670800 3.0 Gallon �� $369.99
670801 3.5 Gallon �� $369.99
651259 4.5 Gallon �� $363.99
651260 5.0 Gallon �� $363.99
SHEET.10
*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.
Please see Cautionary Information in back of catalog.
SHEETMETAL
632930
632931
“Mini Mustang” Gas Tanks by Paughco
These small gas tanks look awesome! Great lines, and only 16 1/2”
long, 9” wide and 7” deep. For custom applications with 2 mounting
styles available. The Narrow “Mini Mustang” tank has a capacity of
2.4 gals., with tunnel measuring 2 1/4” wide x 2 1/2” deep and front/
rear mount tabs. Total length tab center to tab center is 17”. The
Frisco “Mini Mustang” tank has a capacity of 2.2 gals. and features a
Frisco style front mount. Tunnel measures 3” wide x 1 1/2” deep, and
total length tab center to tab center is 15 1/2”. Both tanks have 2,
1/4” NPT petcock outlets; petcocks sold separately. Made in Nevada,
USA by the crew at Paughco.
632930
632931
632252
632253
“Mini Mustang” Gas Tank. Narrow. 2.4 gals. ��$189.99
“Mini Mustang” Gas Tank. Frisco. 2.2 gals.��$189.99
1/4” NPT Petcock. No reserve. (see petcocks) ��$27.99
1/4” NPT Petcock. With reserve. (see petcocks) ��$45.99
Mustang Gas Tank with Pop-Up Cap
3.3 Gallon Mustang Tank
This one piece tank is perfect for a variety of custom applications. It
has rounded mounting plates front and rear that are welded in place.
It features a twin cap look, but the left neck is non-functional, for
appearance only. The 3.3 gallon capacity tank fills on the right-side
only. Tunnel measures 2 1/2"-high x 2 3/4"-wide. Tank measures 18
1/2"-long x 12"-wide.
260143 Unpainted steel��$103.99
Note: All fuel tanks should be test fitted, pressure tested, and pre-sealed before painting.
Comes with a center-mounted single “pop-up” gas cap and has a
capacity of 3.3 gallons. Tank measures 16 1/2"-long x 11"-wide at
widest point. Total length from tip-to-tip of mounting brackets is
approximately 20". Tunnel is approximately 2 3/4"-wide x 2 1/2"deep. Features a 3/8" NPT gas outlet (use CC #’s 12726 or 12727
petcocks) on the center of the bottom right side as well as two
1/4" gas outlets (use CC #’s 632252 or 632253 petcocks) on both
sides near the rear of the tank to be used as a crossover line or, for
multiple choices in routing your gas lines. Petcocks sold separately.
632165 Mustang tank with pop-up cap��$169.99
Special Flush Mount Pop Up Gas Cap
675706 Required for CC # 632165 ��$54.99
Note: All fuel tanks should be test fitted, pressure tested, and pre-sealed before painting.
w w w.cu sto m c h ro m e.co m
SHEET.11
SHEETMETAL
651251
Mustang and Axed Harley-Style Custom Gas
Tanks by Paughco
Available in two popular styles that will bolt right to the stock
frame mounts on 57-03 Sportsters and have an early cam-style
gas cap bung. Made in the U.S.A.
Fits Sportster Models from 82-94; with a 22mm
threaded fuel bung on the right-side of the tank
651251 4.2-gallon Axed Style Custom tank with single gas cap
for 82-94 XL��$205.99
651252 3-gallon Mustang Style tank with single gas cap for
82-94 XL��$205.99
Fits Sportster Models from 95-03; with a 22mm
threaded fuel bung on the left-side of the tank
651253 4.2-gallon Axed Style Custom tank with single gas cap
for 95-03 XL��$205.99
651254 3-gallon Mustang Style tank with single gas cap for
95-03 XL��$205.99
651252
632251
651241
Narrow “Mustang” Style Tank
This sleek looking gas tank features dual bung type caps, holds 2.2
gallons of gas and measures 16 1/2” long, 9” wide and 7” deep.
Tunnel is 2 1/2” wide x 2 1/4” deep. Center line hole-to-hole on
mounting tabs is 17 1/2”. Tank has two 1/4” gas outlets (use our
#632252 or 632253 petcocks). This is a sweet looking tank and goes
great with narrow springers or our girder set-up. Gas caps and
petcocks not included. Made in USA by Paughco.
632251 2.2 gal dual cap narrow mustang type tank��$205.99
651241 2.2 gal single cap narrow mustang tank ��$189.99
SHEET.12
“Wasp” Custom Chopper Gas Tank
Building a trick chopper but haven’t found the prefect tank for it
yet? Look no further! This 2.2 gallon tank with it’s tear drop shape
is perfect for any retro scoot. Available with one or two cam style
bungs, TIG welded with the petcock bung on the right side.
651017 Wasp chopper tank��$139.99
651018 Wasp chopper tank dual cap ��$144.99
*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.
Please see Cautionary Information in back of catalog.
SHEETMETAL
25242
25241
Universal Tank Mounting Kit for Builders
Building your own tank you say, well how are you going to mount it?
This complete set of tank mounts comes with not only the straps and
rubber mounting parts to go on the frame, but also the machined
blocks that are welded into the fuel tank for them to bolt to.
699985 Complete kit��$72.99
25246
25253
25252
Chrome Replacement Petcocks
Chrome-plated duplicates of the stock gas valves used from 75-06. Available
in three different outlet tube options, straight down, left-hand or right-hand
for applications at the front, rear, or either side of the gas tanks. Complete
with a chromed 13/16" nut and nylon mesh filter screen.
25246
Straight down spigot (repl. OEM 62129-75T)��$14.99
25252
25253
25241
25242
12731
Left-side spigot��$17.99
Right-side spigot ��$14.99
Short replacement filter screen �� $5.99
OEM replacement filter screen with reserve tube (repl. OEM
62166-81)�� $5.99
Replacement 3-hole Viton seal (fits latest design with .260"
fuel tubes)�� $1.50
Replacement Filter Screens
260373Fits OEM pre-75�� $3.99
Mounting Kit for Fat Bob Tanks
A ‘must’ when installing CC or Original Equipment Fat Bob tanks on
4-speed frames through 84. Special washers in kit prevent possible thread
damage to rear mounting holes and keep tanks from resting against
heads.
26446
Complete kit��$9.99
Another ‘must’ for installing Fat Bob tanks. One of our mechanics
came up with this little item. It’s actually the chain guard mounting
grommet, but it works great in the front Fat Bob tank mount holes to
isolate the tanks from vibration.
25548
Rubber grommet with a steel insert for use in mounting Fat
Bob tanks. Helps to isolate the tanks from vibration. Pack of 10
(repl. OEM 11411)��$0.65
12726
12727
25245
25243
Chrome Petcocks
Universal Fat Bob Gas Tank Quickmount Kit
A precise and effortless way to mount Original Equipment or
aftermarket Fat Bob tanks to custom or Original Equipment
frames that have had the gas tank brackets removed. It permits
the builder to temporarily attach the one-piece bracket for a
quick visual check of tank placement on custom applications, and
once a tank position is selected, the entire bracket assembly may
be welded in place for a stronger-than-stock, precision system of
support.
25048
Complete kit��$49.99
Engineered and designed to eliminate all internal O-rings. The
innercore design insures against gas leakage while providing
maximum flow. Features a filter screen, reserve setting, and
chrome body.
12726
Fits OEM and custom tanks thru 74 with internal 3/8" NPT
connection (repl. OEM 62125-55B)�� $15.99
12727
3/8” NPT Petcock w/90 degree outlet. With reserve. (see petcocks) ��$15.99
25245
Fits OEM and custom tanks 75-82 with external 13/16" nut
connection (repl. OEM 62163-75) �� $14.99
25243
Same fit as CC #25245 but with 90° barb��$14.99
w w w.cu sto m c h ro m e.co m
SHEET.13
SHEETMETAL
632253
18255
651854
632252
Chrome Fuel Filter
Small size, but packs big protection for your motor. Easily cleaned,
reusable screen.
Chrome
18255
For 5/16" fuel line ��$8.99
18256
For 1/4" fuel line ��$6.99
1/4” Petcocks for Custom Tanks
These petcocks are available with or without the reserve feature, and
fit any custom gas tank such as our aluminum peanut tank (#632501)
and Paughco gas tanks that take 1/4” petcocks.
632252 1/4” NPT Petcock. No reserve. (see petcocks) �� $27.99
632253 1/4” NPT Petcock. With reserve. (see petcocks) �� $45.99
Black
651855
651854
For 5/16" fuel line ��$6.99
For 1/4" fuel line ��$6.99
27050
27051
18240
See-Flow Glass Fuel Filters
668376
Accel High-Flow Petcocks
American-made high-flow petcocks feature chrome-plated bodies
and 5/16" O.D. hose barbs. Other features include a reserve function,
100 micron filtering screens, and easy-to-grasp handles. Bodies are
engineered to prevent leakage, yet deliver maximum fuel flow for
high-performance applications. Two of the petcocks have a swiveling
banjo which rotates 180° for custom hose routing. Fit all Original
Equipment or aftermarket tanks with 22mm bungs.
27051
Petcock with horizontally rotating barb ��$99.99
27050
Petcock with straight down barb ��$79.99
668376 Petcock with vertically rotating barb��$99.99
SHEET.14
A custom in-line fuel filter for 1/4" or 5/16" line.
Chrome
18240
Complete filter for 1/4" line�� $9.99
18239
Complete filter for 5/16" line�� $9.99
Black
651856
651857
Black filter for 1/4” line ��$9.49
Black filter for 5/16” line��$9.49
Replacement filter element
18241
Replacement element ��$2.99
*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.
Please see Cautionary Information in back of catalog.
SHEETMETAL
Dash Panels for Fat Bob Tanks
Chrome Tank Panel
Fits most models with split tanks, cast dash
and a frame-mounted seat from 68-99.
18439
Replaces OEM 61118-81��$27.99
Fits FX and Low Rider models with Fat Bob
gas tanks from 77-84.
26348
Plain (repl. OEM 61647-77T)��$24.99
Steel Chrome Dash for FX
Models
Dash Panel for Fat Bob Gas
Tanks
Fits Fat Bob gas tanks when dash or
instruments are not mounted on tanks.
26344Plain ��$24.99
Stamped steel, chrome-plated instrument
housing for tank mounted gauges on FX
models from 77-84. Includes thick style
tank-to-housing trim rubber and warning
light hole plugs for custom applications.
26339
Dash cover��$39.99
26338
Replacement trim rubber (repl. OEM
61401-82)��$4.99
26308
Hole plugs (pack of 10) ��$1.50
Chrome Dash Kit
All the chrome parts in one convenient kit
to help you convert to the dash used on
several models 77-84. Will not work with
flatside gas tanks.
91339
Complete kit��$55.99
Chrome Skull Nut Cover
Made in the U.S.A. by Wild 1 Mfg. to cover
the hardware that holds the dash in place.
Kits include red rhinestones for the eyes.
Fits the cast dash on models without a dashmounted choke cable.
19971
Sold each��$17.99
632040
632041
Dash Center Mounting Bolt and
Stud
Gas Tank Knee Pads
These universal fit rubber knee pads affix to your tank with double sided adhesive (included)
and give tanks a very cool old school look! Available in 2 sizes to match most any tank
configuration out there. The smaller size measures approx. 7” long x 3 1/2” tall at the highest
point. The larger version measures approx. 7” long x 4” tall at the highest point. Stick these
puppies on your tank and stand out from the crowd! Sold as pairs.
632040 Gas tank knee pads-Small�� $21.99
632041 Gas tank knee pads-Large�� $29.99
Includes chrome-plated center screw with
stud and hardware. Fits Big Twins from 47-67
as original part replacement or can be used
on custom applications where choke wire is
not brought through dash.
26162
Sold each��$5.99
w w w.cu sto m c h ro m e.co m
SHEET.15
SHEETMETAL
26188
Three-Light Dash Mounting
Plate
25972
Two-Light and Three-Light
Dashes for Fat Bob Tanks
Show-chrome dash covers complete with
lenses and trim rubber. Replacement lenses
and trim rubber also available separately.
26188
2-light dash��$44.99
25972
3-light dash��$40.99
26180
Replacement trim rubber ��$4.99
Classic Cast Dashes
Heavy-duty zinc die-cast dashes are
beautifully chrome-plated duplicates of their
Original Equipment counterparts. Complete
in every detail, each dash also includes the
lenses, light divider, and trim rubbers. May
be installed on most 4-speed frames and
Softail models when the appropriate dash
base is used.
26187
Fits all models 68-90 (replaces OEM
71241-68B)��$69.99
26186
Fits all models with self-cancelling
turn signals from 91-95 (except
Dyna Wide Glide models) replaces
OEM 71241-91 ��$69.99
Includes wiring and sockets.
25971
Fits CC dash #25972��$39.99
26191
Replacement dash base light sockets
(pack of five)��$22.99
Replacement Parts
These pieces will fit Original Equipment
dashes as well as the dashes listed above.
26239
Lens kit: Includes lenses, divider and
hardware��$9.99
26240
Trim rubbers (pair) replaces OEM
71295-68 ��$4.99
26238
Cast dash mounting plate��$44.99
Late-Style Cast Dash Mounting
Plate
A complete mounting kit for many models
with cast dashes from 68-99 (except Dyna
Wide Glide models). Includes all the
hardware and spacers necessary to fit both
the standard early-style Fat Bob tanks and
the later-style flatside Fat Bob tanks. Also
included are the circuit breaker clips, the
rubber strip for mounting circuit breakers
with flatside tanks, ignition switch mounting
screws, three insulated terminal studs and
five light sockets with bulbs. Everything
necessary for a quick and easy installation.
26238
Cast dash mounting plate��$44.99
26191
Replacement dash base light sockets
(pack of five)��$22.99
Plain Dash Mounting Plate
Cateye Dash for Fat Bob Tanks
Show-chrome cateye-style dash with lenses.
Replacement lenses are sold each.
26189
Cateye dash��$39.99
26356
Cateye red lens-plastic ��$4.99
SHEET.16
Basic mounting plate for use with Fat Bob
dash covers #25972 and #26188 when dash
lighting is not desired.
25235
Without dash lights��$14.99
*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.
Please see Cautionary Information in back of catalog.
SHEETMETAL
Odometer Reset Cable for FX Models
Trimlok Dash Trim
Easy-to-install, while providing style and protection. Genuine Trimlok
steel reinforced vinyl trim is cut to length to fit all stamped steel
two and three-light dashes. Available in pre-cut 27 inch and 10 foot
lengths in plain black.
26181
Black (27"-long)��$4.99
26241
Black (10 feet-long)��$1.00
Complete odometer reset cable assembly for all 4-speed FX models
(except FXWG) 73-84. Includes chrome knurled knob, rubber
grommet, washer, spring and flexible cable. Fully assembled, ready
to install.
26445
Replaces OEM 67210-73T��$10.99
Hi-Beam Indicator Lamp
Original style, multi-piece high beam indicator lamp assembly with
replaceable bulb included. Fits FX models from 73-74, as well as
Sportster models from 68-73. Can also be used to replace the onepiece ‘throwaway’ indicator lamp used on FX models from 75-85.
26444
Replaces OEM 67891-68��$8.99
Trim Rubber for Low Rider Dash
Thick style, black rubber trim for FX dual gauge housings. Neatly fills
the open space between the tanks and the instrument housing while
isolating the gauges from vibration.
26338
Replacement trim rubber (repl. OEM 61401-82) ��$4.99
310154
26356
26352
Dash Switch Decal
Fits FL models from 68-84, FX models
from 71-72, FXWG models from
80-86, and Softail models from 84-99.
Sold in pack of 5.
310136
Replaces OEM 71300-79
��$2.00
26353
26354
Replacement Lenses for Fat Bob Dash Covers
Can be used to restore Original Equipment dashes or as
replacement parts for CC dashes. Sold each.
26356
Cateye red lens-plastic ��$4.99
26354
3-light dash red lens (2 used) – plastic ��$5.99
26353
3-light dash blue lens (1 used) – plastic ��$5.99
26352
2-light dash red lens – plastic��$4.99
310154 Cateye dash lens, green��$4.99
Instrument Light Socket
Assemblies
OEM style replacement light socket
assemblies include socket with wire and
bulb. Available for most Big Twins and
Sportster models 76-97. Sold in 5 packs.
310113 Steel, 1 wire type��$4.80
Chrome Dash Cover Screws
Complete 4-piece set of chrome plated, buttonhead panel screws.
Fit all Low Rider and FXEF dashes 77-84.
26441
Set of 4��$3.99
w w w.cu sto m c h ro m e.co m
SHEET.17
SHEETMETAL
260032
260005
688531
Deluxe Scalloped Gas Caps
Chrome deluxe gas caps with scalloped edges. Available vented or
non-vented for most Big Twin and Sportster models. Also fits most
after-market replacement gas tanks.
For 41-73 models
260030Vented ��$15.99
260031Non-Vented��$15.99
260032 Deluxe gas cap set (one vented and one non-vented cap)
��$29.99
For 84-95 models
688530 Deluxe gas cap set chrome (one vented and one non-vented
cap)��$38.99
688531 Deluxe vented gas cap chrome ��$19.99
688532 Deluxe non-vented gas cap chrome��$19.99
688536 Deluxe gas cap set black (one vented and one non-vented cap)
688537
688538
651863
Early-Style Gas Caps for Late 65-72
��$38.99
Chrome gas caps for Big Twin and Sportster models from 65-72
(except FLT and FXR models).
Chrome
260003 Vented (repl. OEM 61103-35)��$8.99
260005 Gas cap set. Includes one vented and one non-vented (repl.
OEMs 61103-35 and 61103-65)��$16.99
Deluxe vented gas cap black��$19.99
Deluxe non-vented gas cap black ��$19.99
Black
651863
For 96-Up models
688533 Deluxe gas cap set chrome (one vented and one non-vented
cap)��$38.99
688534 Deluxe vented gas cap chrome ��$19.99
688535 Deluxe non-vented gas cap chrome��$19.99
688539 Deluxe gas cap set black (one vented and one non-vented cap)
651864
Black gas cap set. Includes one vented and one non-vented
(repl. OEMs 61103-35 and 61103-65) ��$11.99
Black vented (repl. OEM 61103-35)��$6.49
��$38.99
688540
688541
Deluxe vented gas cap black��$19.99
Deluxe non-vented gas cap black ��$19.99
Original-Style
Cam-Style Gas Caps
651853
Steel Gas Caps
26580
Perfect mechanical reproductions of the Original Equipment parts.
The low-pressure relief vent is properly recessed in the cap to clear
the filler neck vent tube. For screw-style tanks from 83-95.
Chrome
26580
Set of left and right caps��$21.99
26582
Right side cap only (vented) replaces OEM 61102-83A ��$10.99
26581
Left side cap only (non-vented) replaces OEM 61103-83��$11.49
Black
651862
651853
651861
SHEET.18
Black set of left and right caps��$21.99
Black right side cap only (vented) replaces OEM 61102-83A
��$10.99
Late-Style
A variety of replacement and custom gas caps. Available vented
for single cap gas tanks and the right side of Fat Bob gas tanks, or
without a vent for the left side of Fat Bob tanks. They fit Original
Equipment and replacement tanks with cam-style bungs.
Polished Stainless Steel Late-Style Caps
Includes left and right caps for Fat Bob tanks.
26574
Plain cap set ��$29.99
26570
Vented cap ONLY (repl. OEM 61102-73) ��$14.99
26571
Non-vented cap ONLY (repl. OEM 61103-73A)��$14.49
Chrome Original-Style Gas Caps
Includes left and right caps for Fat Bob tanks.
26499
Plain cap set ��$11.99
12725
Plain vented cap ONLY (repl. OEM 61103-36)��$9.99
26021
Plain non-vented cap ONLY (repl. OEM 61103-65) ��$7.99
Black left side cap only (non-vented) replaces OEM 61103-83
��$10.99
*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.
Please see Cautionary Information in back of catalog.
SHEETMETAL
47715
Custom Pop-Up Gas Caps
• Vented gas caps that don’t protrude from the surface
of the gas tank at all!
• To access the filler, you press and twist... the cap pops
up, then unscrews normally
• For custom “weld-in” applications ONLY
• Sold each
47715
Stainless steel bung and cap��$99.99
Replacement Pop-Up Caps ONLY
47775
Stainless Steel (sold each) ��$42.99
47777
Chrome (sold each)��$42.99
Custom Mini Gas Cap Kit
The gas cap is CNC-Machined from billet aluminum with a knurled edge with a
satin/raw finish (gas cap has an O.D. of 1.75”). Kit comes complete with gas cap
and steel weld-in bung.
641909 Mini weld-in gas cap��$39.99
Polished Aluminum Skull Gas Cap Cover
Multiple skull design cast from an original hand-carved
mold . Attaches to OEM style gas caps with epoxy (not
included).
37735
Sold each��$21.99
19037
19006
‘Live To Ride’ Gas Cap Covers
Covers with chrome eagles feature a ‘A Way of Life’ banner. Gold eagles have
‘Eagle Spirit’ banners. They attach with double-sided foam tape and fit all late
model gas caps (except molded plastic caps).
‘A Way of Life’
19006
Chrome eagle (sold each) ��$10.99
3-Dimensional Gas Cap Covers
Distinctive covers are sand-cast from hand-carved
originals. Designed to fit over OEM style caps. Glue them
on with 5-minute epoxy, or use silicone adhesive. Sold
each.
37863Skull ��$38.99
37868Flame ��$27.99
‘Eagle Spirit’
19037
Gold eagle (sold in pairs)��$33.99
w w w.cu sto m c h ro m e.co m
SHEET.19
SHEETMETAL
650231
Custom 3 qt. ‘Barrel’ Style Oil Tanks by Santee
Chrome Oil Tank for FXR Models
A complete chrome oil tank assembly for all FXR models from 82-90
(except 86-up FXR Super Glide models). Adds sensational style and
simplifies oil draining through the addition of a second drain hole
on the left rear of the tank. Included with the tank is a remote drain
hose fitting kit which allows it to be drained from the kickstand
side through a rubber hose which, when not in use, plugs onto a
frame mounted dummy fitting which is included in the kit. Machine
polished and then triple chrome-plated. Replaces OEMs 62406-81,
62406-86 and 62414-86.
28104
Oil tank and remote drain kit (this tank has no oil level "sight"
glass)��$119.99
16051
Well-nuts blind fasteners (repl. OEM 8099) pack of 10 ��$1.30
These Chrome steel oil tanks were styled after the classic ‘Barrel’
tanks on choppers from the 60’s and 70’s. They have a universal
mounting system so they will fit just about anything and are available
with or without a spin-on filter. Kits include 3 rubber mounts and
tank cap.
650231 3 qt. round oil tank�� $329.99
650232 3 qt. round oil tank with spin-on filter�� $379.99
650235
651266
78305
Chrome Wrap-Around Oil Tank by Santee
78301
Chrome Replacement Oil Tanks
These 4 qt. oil tanks will fit rigid frames and 58-64 swingarm frames
with kickstart and steel primaries, but will NOT fit models with
aluminum primaries or 79-84 4-speed transmissions.
650235 Chrome center fill oil tank ��$165.99
651266 Chrome side fill oil tank with spin-on oil filter��$339.99
Duplicates of the Original Equipment oil talks finished in brilliant
chrome.
78301
Fits 4-speed FL and FX Big Twin models from 82-86 (repl. OEM
62504-82)��$149.99
78305
Fits 4-speed FL and FX Big Twin models from 65-E82 (repl. OEM
62504-65A) ��$124.99
650219
650218
Oil Tanks for XL Rigid Frames by Paughco
This oil tank is for use with rigid Sportster frames manufactured by
Paughco. Drain plug sold separately. Made in USA by Paughco.
632247 Oil tank for use w/Paughco XL rigid frames��$175.99
632248 Oil tank drain plug ��$7.99
SHEET.20
Custom Oil Tanks for FL/FX Models and Santee
4-speed Swingarm Frames
3.5 qt. chrome oil tanks for 65-86 FL and FX 4-speed models, that
provide easy access to the battery, and bolt to the stock mounts.
They will also fit Santee 4-speed swingarm frames. Kits include oil
tank and 2-pc. front mounting bracket for an easy installation.
650218 Chrome side fill��$339.99
650219 Chrome side fill with spin-on filter��$369.99
*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.
Please see Cautionary Information in back of catalog.
SHEETMETAL
27101
27100
Bobber-Style Oil Tanks with Battery Box
Here is a old school oil tank for your next bobber bike project.
Chrome steel tanks with built-in battery boxes come with front
rubber mount and tank cap included. They fit Big Twin rigid
frames from 36-57 and most custom rigid frames on the market
today, also 84-99 Softail models. Lines come out of the bottom of
the tank for a nice clean look.
632062 ‘Domed’ oil tank ��$299.99
Chrome Oil Tank Dipsticks
Chrome-plated replacements for Original Equipment dipsticks.
27100
With short dipstick for Softail models from 84-99 and
Sportster models from 82-03 (repl. OEM 62595-82A)��$8.99
27101
With long dipstick for FL models from 70-84, FX models
from 71-85, FXR models from 82-83, FLT models from 80-86
and XLCH models from 70-78 (repl. OEM 62625-70A)��$8.99
650233
Oil Tank Plug
Custom Wrap-Around Oil Tanks for Big Twins by
Santee
Chrome-cap oil tank super plug for all Original Equipment side-fill
oil tanks from 65-99 and most custom tanks.
25674
Replaces OEM 62644-84T��$5.99
3.5 qt. custom wrap-around oil tanks. Available with or without
spin-on oil filter and in either a side or center fill. When used with
an FXE battery they’ll fit rigid and 58-64 swingarm frames, and will
also clear 79-84 4-speed transmissions.
Side Fill
650233 Custom 3.5 qt. oil tank with threaded oil line fittings��$239.99
650234 Custom 3.5 qt. oil tank with threaded oil line fittings and spinon filter ��$324.99
651262
651263
Wrap-Around Oil Tank for Electric Start Sportster
Models
This 3 1/2 quart oil tank will accept the stock FXE electric start
battery. It also fits all 67-78 stock electric start Sportster models, and
is adaptable to many custom frames (on 73-78 stock frames, the
removal of the rear frame support struts may be required).Comes
complete with a cap, oil line fittings, and mounting hardware.
12599
Chrome oil tank��$239.99
Replacement Oil Tank Caps by Paughco
Replacement oil tank caps for most side and center fill oil tanks.
Made in the U.S.A.
651262 Chrome-plated 1 1/16”-24 threaded cap for top fill oil tanks
��$26.99
651263
Chrome-plated push-in rubber filler plug for side fill oil
tanks��$14.99
w w w.cu sto m c h ro m e.co m
SHEET.21
SHEETMETAL
Chrome Oil Tank Cap Assembly
For stock oil tanks on all 4-speed Big Twin models (except Softail
models) thru 82 and 67-E78 Sportster models with electric start.
12352
Replaces OEM 62610-52TA ��$27.99
25334
Oil tank gasket 66-82 (pack of 10) replaces OEM 62628-66
�� $0.85
Early-Style Accessory Oil Filter System
Accurate reproduction of the early accessory oil filter kit used on
40-64 Big Twins. Can be easily fitted to 4-speed and Softail models.
26652
Chrome oil filter assembly with gasket kit and filter (replaces
OEMs 63800-48 and 63800-58)��$52.99
26656
Gasket kit for oil filter assembly ��$4.99
26657
Filter element (sold each) ��$3.49
Note: Does not include oil hose.
270019
Generator Oil Filter Adapter
This adaptor allows you to install an oil filter in place of the
generator on 36-69 motors as well as our Pandemonium or S&S
Shovelhead engines with generator/alternator bottoms. Use OEM
63796-77A or equivalent aftermarket oil filter. Chrome finish.
632025 Generator oil filter adapter ��$114.99
633244
633245
25247
25248
Oil Filter Kits
Full flow automotive style spin-on oil filter kits. Each of these custom kits
includes a chromed heavy-gauge steel bracket, chrome disposable oil
filter, and all required hoses and clamps for installation.
25247
Fits all 70-78 Big Twins without front motor mounted rectifier/
regulator (mounts on top of front motor mount) ��$57.99
25248
For all Sportster models 57-77 (mounts to left front motor
mount location)��$55.99
270019 Fits frame tubes, excellent for custom applications ��$51.99
25250
Chrome oil filter (replaces OEM #63796-77A) �� $8.99
Chrome Oil Fitting 1/4 NPT x 90 and Hose Barb 1/4
NPT x 3/8
Oil line fittings and hose barbs to connect oil lines to Santee oil tanks
(CCI# 631990-91)
Oil line fitting
633244 1/4 NPT x 90��$7.49
Hose Barbs
633245 1/4 NPT x 3/8��$5.99
SHEET.22
Rubber Mounts
Replacement rubber mount is used for mounting Harley battery
boxes and oil tanks. Made of quality rubber with 1/4"-20 x 1/2" long
threaded studs and steel plates. This mount also works great for
mounting many custom parts. Replaces OEM 62563-65.
16055
Pack of 10 ��$2.80
*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.
Please see Cautionary Information in back of catalog.
SHEETMETAL
16050
Rubber Vibration Resistant Mounting Studs
This is just the answer for custom builders. These studs are perfect
for mounting gas and oil tanks. Sold in packs of 5 (unless otherwise
noted).
16050
1/4"-20 x 1/2" stud both ends��$1.80
Spin-On Oil Filter Kit
A high-tech replacement for your canister-type oil filters. It’s
approximately the same size as the stock unit and accepts CC #25250
chrome spin-on filter to eliminate leaks. Makes filter changes clean
and easy. Comes with both threaded and slip-on fittings. Uses our
mounting brackets.
26650
Spin-on filter kit��$53.99
25250
Chrome oil filter (replaces OEM #63796-77A) ��$8.99
26653
26654
26655
Oil Filter Mounting Brackets
Chrome steel brackets to mount accessory oil filters. Designed for use
in conjunction with CC #’s 26650 or 26652 oil filter kits. Available for
rigid and swingarm 4-speed Big Twin frames from 40-86.
26653
Fits 40-57 rigid frames (repl. OEM 63860-50) ��$9.99
26654
Fits 58-64 swingarm frames (repl. OEM 63860-58A)��$9.99
26655
Fits 65-86 4-speed frames (except Softail models)��$9.99
Crimp Hose Clamps
OEM style hose clamps. Note: Diameters listed are before crimping.
Sold in packs of 50.
260482 17/32" (.531) diameter. Fits 1/4" I.D. reinforced rubber fuel
line and vent hoses (repl. OEM 10014)��$0.32
260483 19/32" (.594) diameter. Fits 5/16" I.D. rubber remote brake
reservoir hose (repl. OEM 10038)��$0.32
260484 11/16" (.687) diameter. Fits 3/8" I.D. reinforced rubber oil
and vent hoses (repl. OEM 10020A) ��$0.32
260485 13/16" (.812) diameter. Fits all tank drain hoses (repl. OEM
10086)��$0.32
020538
Oil Line Fittings
Chrome fittings used for oil tank, oil pump, oil coolers, carb fuel
inlet, etc. Sold in 5 pack.
020531Straight fitting. 3/8" hose to 1/8" NPT. Replaces OEM 63533-41
��$1.60
Filter Pac
Custom oil filter and regulator mount designed to clean-up front
lower mount area. Attaches to the front of the engine. Includes
a chrome billet aluminum base plate, chrome hose fittings and a
chrome oil filter. Utilizes stock regulator. Fits all Softail and 4-speed
Big Twin models from 75-99.
25270
Complete kit��$64.99
26109
Replacement chrome oil filter (replaces OEM 63782-80)��$6.99
020533Straight fitting. 5/16" hose to 1/8" NPT ��$4.00
020535Straight fitting. 5/16" hose to 1/4" NPT ��$3.80
02053690° fitting. 5/16" hose to 1/8" NPT. Replaces OEM 62375-57
��$6.80
020538Plug – 1/8" NPT (repl. OEM 42311-58)��$3.00
020539Pipe plug, 1/4" NPT ��$3.60
w w w.cu sto m c h ro m e.co m
SHEET.23
SHEETMETAL
688250
688251
84753
Oil Line Retainers for Twin Cam Models
Every time the oil lines are removed from the oil tank these retainers
should be replaced in order to avoid any leakage.
688250 Oil line retainers (pr) to engine OEM 63632-00�� $14.99
688251 Oil line retainers (pr) to tank OEM 63783-00 �� $14.99
20235
20234
Oil Line T-Piece and Fittings
Brass T-piece with 3/8" spigot and chrome-plated oil line fittings with
1/8" NPT thread and 3/8" spigot. Sold each.
84753
Brass T-piece ��$8.15
20235
Chrome hose fitting, 3/8" hose. (repl. OEM 63533-41) Sold each
��$4.99
20234
12533
Elbow, 90°��$4.99
12534
Original-Style Oil Pump Fittings
Original-style fittings used with some custom oil tanks to convert
nipples so stainless-steel braided lines may be used. Set of 3.
12533
Fit nylon and braided hose��$7.99
12534
Fit steel and braided fixed-end lines�� $12.99
SHEET.24
*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.
Please see Cautionary Information in back of catalog.
SHEETMETAL
270609
270608
270606
Custom Hose Clamps
Fits over oil and fuel lines. Available with
chrome or blue anodized finish. Sold in 6
packs.
270600 Chrome. Fits 3/8" and 5/16" I.D.
hoses (up to 5/8" O.D.)��$4.33
270604 Blue. Fits 3/8" and 5/16" I.D. hoses
(up to 5/8" O.D.) ��$4.17
270601 Chrome. Fits 1/4" I.D. hose (up to
1/2" O.D.)��$4.17
270605 Blue. Fits 1/4" I.D. hose (up to 1/2"
O.D.)��$4.17
270607
Custom Hose Clamps
Mini Hose Clamps
Quality clamps for all 7/32" to 5/8" O.D.
hose.
19883
Card of 24 ��$0.83
19878
Box of 10��$0.70
These custom hose clamps feature a great
look with reliable function. Under each
custom hose cover is a weather resistant
worm-drive hose clamp. Sold in packs of 6.
270606 3/8"-diameter. Slotted ��$4.33
270607 1/4"-diameter. Slotted ��$4.33
270608 3/8"-diameter. Grooved��$4.17
270609 1/4"-diameter. Grooved��$4.17
380305
380351
380300
380303
380302
380353
380301
380352
Hose Separators
Available in plain or ball milled to match our
other custom accessories, these die-cast hose
separators will fit 3/8" or 5/16" I.D. rubber or
stainless steel oil and fuel lines on Big Twin
and Sportster models. Sold each.
Ball
Milled
Price
Plain
Price
380300
$7.99
78396
$7.49 Chrome
380301
$7.99
380351
$7.49 Polished
380302
$6.99
380352
$6.99 Blue
380303
$7.99
380353
$7.49 Black
Triple Hose Separator
Keep lines neatly bundled with these
separators fit 3/8" or 5/16" rubber or
stainless steel hoses. Secures with flush
sockethead screws.
380305Chrome��$9.99
380355 Chrome ball milled ��$9.99
25460
Oil Pressure Switch
Quality replacement oil pressure switch
for XL and K models 54-76 and Big Twin
(except Evo) 41-84. Replaces OEM 2655272, sold each.
688594 Oil pressure switch (repl. OEM
26552-72)��$10.99
17714
Oil Pressure Switches
25464
25463
Accel Oil Pressure Switches
Replacement switch has heavy-duty contacts
and thermoplastic insulator. Made in the
USA. Fits FXD 99, Big Twin 99-13 (except
models with electric oil pressure gauges).
17714
Oil pressure switch. Replaces OEM
26561-84��$10.99
American-made units with heavy-duty
contacts, brass ferrule, thermoplastic
insulator and a bright finish.
Fits Sportster and K models from 54-76
and Big Twins from 41-84 (except
Evolution models).
25460
Replaces OEM 26552-72��$15.99
Oil Pressure Switch Wrench
Avoid scratching or damaging your oil
pressure switch during installation or
removal with this handy two piece tool.
688722 Oil pressure switch wrench��$17.99
Fits Sportster models from 77-03
25463
Replaces OEM 26554-77��$16.99
Fits Evolution Big Twin models from
84-99 (except models with electric oil
pressure gauge)
25464
Replaces OEM 26561-84��$13.99
w w w.cu sto m c h ro m e.co m
688635
Twin Cam Oil Pressure Switch
Oil pressure switch for all Twin Cam models
and V-rod models 02-Up. Sold each.
688635 Oil pressure switch (repl. OEM
26561-99)��$5.99
SHEET.25
SHEETMETAL
260530
614004
Stainless Steel Braided Hose
Sold in 25 ft. rolls.
260530 1/4" ID x 25’��$79.99
260532 5/16" ID x 25’ ��$87.99
260534 3/8" ID x 25’��$99.99
12428
Goodridge “All Black 210 Oil Line Kits”
All black oil line kits for V-Twins. Featuring our premium black
braided oil hose. Hose has outer fabric braided cover with stainless
braided core, coated with a neoprene inner lining. Kits ship complete
with black anodised hose clamps.
614004* 6 ft 210 Oil Line Kit��$78.99
614005** 12ft 210 Oil Line Kit ��$142.99
614006 210 Black Braided Oil Hose, 6ft ��$47.99
614007 210 Black Braided Oil Hose, 12ft ��$99.99
614008 3/8” Black Hose Finishers - 6 Pak ��$31.99
614009 3/8” Black Hose Finishers - 10 Pak��$47.99
*Contains 6 ft of 210 hose and 4ea Black Hose Finishers
**Contains 12 ft of 210 hose and 8ea Black Hose Finishers
12427
Overhead Rocker Arm Oil Lines
Set of two stainless steel braided oil lines with chrome NPT fittings.
12427
Fits 66-84 Shovelheads��$15.99
12428
Fits 57-85 Sportster models��$16.99
28015
28016
Goodridge Custom Stainless Steel Oil Line and
Fittings
Custom oil lines are made simple with Goodridge’s new do-it-yourself
reusable oil line components. This new system utilizes the same
chrome steel fittings Goodridge is known for, but in a user-friendly
format that allows you to make your own kit. These ground breaking
fittings are coupled with their stainless steel braided PTFE lined hose
and can be used to assemble oil line kits for virtually any Big Twin on
the road.
610250 12Ft roll –6 stainless Teflon hose��$107.99
610251 Chrome oil tank stub fitting��$40.99
610252 Chrome straight oil fitting 1/8 NPT��$30.99
610254 Chrome 90 degree oil fitting 1/8 NPT��$37.99
SHEET.26
Chrome Rocker Oil Lines
Chromed rocker box oil lines for Sportster models and Shovelheads.
Includes complete set of fittings and seals (2 lines).
28015
Fits Shovelheads 66-84 (repl. OEMs 62783-66A, 62785-66A)
��$13.99
28016
Fits Sportster models (except magneto models) from 57-85
(repl. OEM 17324-57A)��$13.99
Rocker Box Oil Line Fittings
Includes chrome fittings and seals for the rocker box oil lines on all
Sportster models and Shovelheads 57-85.
010421 Sold in pairs (repl. OEMs 63527-57A, 63526-57)��$5.99
12074
Motor Factory oil line sleeves ONLY (repl. OEM 63529-57) pack
of 10��$0.25
*Prices shown are suggested retail prices only. Actual retail prices are determined by each dealer and may vary.
Please see Cautionary Information in back of catalog.
SHEETMETAL
General Warnings.
Motorcycle riding is a dangerous activity. The only way to be sure to avoid injury is not to ride! Even if you use the finest and best-maintained
equipment, wear a helmet and protective clothing, and take all possible precautions, it is not possible to avoid every risk. Motorcycle accidents
frequently result in serious injury, including death. Please do not operate a motorcycle or other motor vehicle when you are tired or under the
influence of alcohol or drugs, or when your perception is impaired for any other reason. At all times, please wear a helmet, ride carefully and
within posted speed limits, and obey all other traffic regulations and instructions from law enforcement personnel.
Custom Chrome, sells aftermarket motorcycle parts for Harley-Davidson® and other brands. If you do not have the necessary experience and
skill, please have a qualified mechanic install any new or replacement part on your motorcycle. The failure to install properly and test any new
or replacement component could adversely affect your motorcycle’s operation and result in an accident, including a fatal accident.
Federal and state laws and regulations impose restrictions on modifying the engine, ignition, exhaust and other components of a motorcycle
intended for on-road use. In addition, these laws and regulations impose requirements on windshields, brake components, lighting, and other
equipment on your motorcycle. Accordingly, certain parts in this catalog are for competition or display purposes only. In general, those parts
are indicated by a “Competition” mark: a checkered flag in a yellow oval.
If you are a retail customer, you are responsible to know the laws and regulations that govern the modification of your motorcycle. Custom
Chrome is not responsible if you modify your motorcycle or any component in violation of law. If you have any questions regarding a particular
component, please consult your dealer or a qualified motorcycle mechanic.
The following is additional information relating to components for sale in various sections of this catalog. This information is not exclusive
– if you have any questions regarding the installation or use of any component, please contact your dealer, a qualified mechanic, or Custom
Chrome’s customer service department.
These fine Jammer products are found in the
2014 Custom Chrome Catalog
Use the Dealer Locator at
customchrome.com to find your
local Custom Chrome Dealer
This symbol appearing throughout our catalog means that
the specified items are high-performance exhaust, carburetor,
ignition, or engine components and are not legal for use on
pollution or noise-controlled vehicles (except in organized and sanctioned
racing or competition events). It is a violation of federal law and the law in
every state to install or use any of these components on motorcycles that are
licensed for street use or used on public roads. Penalties are substantial. CCI
offers these components solely for competition, display, or other off-road use,
and is not responsible for any illegal application or use thereof.
© COPYRIGHT 1982-2014 BY CUSTOM CHROME - A DIVISION OF DAE-IL USA, INC.
ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED,
STORED IN A RETRIEVAL SYSTEM OR TRANSMITTED IN ANY FORM OR BY
ANY MEANS; ELECTRONIC, MECHANICAL, PHOTOCOPYING, RECORDING, OR
OTHERWISE WITHOUT PRIOR WRITTEN PERMISSION OF THE PUBLISHER.
w w w.cu sto m c h ro m e.co m
SHEET.27
155 East Main Ave. | Suite 150 | Morgan Hill, CA 95037