Tariff Concessions - 7301 to 7310.29.00
Tariff Description =========================================================================== 7302.10 RAILS, flat bottom, less than 20 kg/m Op. 21.02.1984 Dec. 21.02.1984 - TC 8341714 7302.10 RAILS, crane, railway type, weight EXCEEDING 70 kg/m Op. 14.06.1988 Dec. 18.08.1988 - TC 8805556 7302.10.00 RAIL, grooved, profile type 51R1 Op. 30.03.2012 Dec. 18.06.2012 - TC 1210533 7302.10.00 PROFILES, CONSTRUCTION RAIL, type 105C1, having ALL of the following: (a) height NOT less than 178.5 mm and NOT greater than 181.5 mm; (b) base width NOT less than 177 mm and NOT greater than 183 mm; (c) rail head width NOT greater than 130 mm Op. 22.12.2011 Dec. 19.03.2012 - TC 1142352 7302.10.00 RAIL, grooved, being ANY of the following: (a) Ri57A; (b) 57A (c) Ri60R1; (d) Ri60; (e) Ri60-10; (f) 60Ri1; (g) 60R1 Op. 09.07.2010 Dec. 29.09.2010 - TC 1031338 RAIL TRACK, comprising NOT less than 0.84% carbon Op. 10.08.2005 Dec. 28.10.2005 - TC 0510522 RAIL, having ALL of the following: (a) elevated guardrail configuration; (b) overall height 93 mm; (c) rail head height 38 mm; (d) neck height 40 mm; (e) base (foot) height 15 mm; (f) rail head width 80 mm; (g) base (foot) width 40 mm Op. 22.06.1998 Dec. 28.08.1998 - TC 9805404 7302.10.00 7302.10.00 7302.30.00 RAIL POINTS, ASYMETRICAL, tongue rail configuration, having ALL of the following: (a) base width NOT greater than 150 mm; (b) overall height NOT greater than 172 mm; (c) rail head width NOT greater than 74.5 mm; (d) rail head height NOT greater than 53 mm; (e) neck height NOT greater than 89.5 mm Op. 25.05.2010 Dec. 17.08.2010 - TC 1023361 7302.30.00 RAIL, ASYMMETRICAL POINTS, having ALL of the following: (a) tongue rail configuration; (b) base width 140 mm; (c) overall height 134 mm; (d) rail head width 74.5 mm; (e) rail head height 53 mm; (f) neck height 47.3 mm Op. 09.04.1998 Dec. 10.06.2010 - TC 1025922 7302.90.00 CLIPS, CRANE RAIL Op. 05.06.2008 7303.00.00 Dec. 22.08.2008 - TC 0811455 PIPES, cast iron, complying with European Standard EN877:1999 (EN877:1999) having EITHER of the following: Item 50 applies unless otherwise stated. Tariff Description =========================================================================== (a) internal coating of epoxy resin, outer coating of acrylic primer; (b) internal coating of epoxy, outer coating of zinc and acrylic primer Op. 14.09.2006 Dec. 08.12.2006 - TC 0617186 7304.11.00 7304.19.00 7304.19.00 LINE PIPE, seamless, stainless steel Op. 04.04.2007 Dec. 22.06.2007 - TC 0704964 LINE PIPE, seamless, circular cross section, complying with American Petroleum Institute Standard Specification 5L (API 5L), having EITHER of the following: (a) diameter less than 33.7 mm; (b) diameter exceeding 168.3 mm Op. 20.07.2012 Dec. 12.11.2012 - TC 1224023 LINE PIPE, carbon steel, conforming to American Society of Testing and Materials ASTM A106 Grade B, being ANY of the following, as listed in THE TABLE: THE TABLE TYPE OD WT (a) 200NB Schedule 160 219.10 mm 23.01 mm; (b) 250NB Schedule 80 273.10 mm 15.09 mm; (c) 200NB Schedule 40 219.10 mm 8.18 mm; (d) 80NB Schedule 80 88.90 mm 7.62 mm; (e) 20NB Schedule 160 26.7 mm 5.56 mm For the purposes of this order, all measurements have a tolerance of + OR - 5% Op. 05.01.2011 Dec. 04.04.2011 - TC 1100573 7304.19.00 LINE PIPE, seamless, circular cross section, having EITHER of the following: (a) outside diameter (OD) NOT greater than 168.3 mm; (b) wall thickness (WT) NOT less than 16 mm, and complying with EITHER of the following: (a) American Society of Testing and Materials Standards A106/A106M - 08, grade B (ASTM A106/A106M - 08, grade B); (b) American Petroleum Institute Standard API specification 5L, grade X42 (API specification 5L, grade X42) Op. 13.08.2010 Dec. 08.11.2010 - TC 1037312 7304.19.00 LINE PIPE, seamless, to Specification ASTM A333 Grade 6, having EITHER of the following: (a) OD exceeding 209.0 mm; (b) a WT of 12.5 mm or greater Op. 01.01.2007 Dec. 08.11.2006 - TC 0614208 7304.19.00 TUBES OR HOLLOW BARS (NOT BEING HONED TUBES), in straight lengths, ends plain, bevelled or threaded in accordance with ANY of the following tube, hollow bar or pipe material Specification options: (a) AS; (b) ASME; (c) ASTM; (d) BS; (e) DIN, but without further rework, having a length NOT less than four times the OD, as listed in THE TABLE: THE TABLE Outside Dia Wall Thickness (a) NOT exceeding 219.08 mm 13.00 mm or greater but Item 50 applies unless otherwise stated. Tariff Description =========================================================================== NOT exceeding 25.00 mm; (b) 219.08 mm or greater but 12.70 mm or greater but NOT exceeding 254.00 mm NOT exceeding 50.80 mm; (c) 254.00 mm or greater but 19.05 mm or greater but NOT exceeding 323.85 mm NOT exceeding 41.00 mm; (d) 323.85 mm or greater but 25.40 mm or greater but NOT exceeding 720.73 mm NOT exceeding 75.00 mm Op. 01.01.2007 Dec. 08.11.2006 - TC 0614209 7304.19.00 TUBES, (a) (b) (c) 7304.19.00 PIPES, STEEL, having a diameter NOT less than 65 cm Op. 24.01.2007 Dec. 13.04.2007 - TC 0701302 7304.19.00 LINE PIPE, seamless, to DNV-OS-F101 Op. 01.01.2007 Dec. 06.03.2007 7304.23.00 seamless, conforming to ALL of the following: specification API 5L-X42 OR API 5L-X60 OR API 5L-B; OD less than 153.4 mm OR greater than 482.3 mm; resistance to stepwise cracking and tested to NACE standard TM02-84 Op. 01.01.2007 Dec. 08.11.2006 - TC 0614211 - TC 0703467 DRILL RODS, rotary drilling, having ALL of the following; (a) friction welded male AND/OR female fittings; (b) tensile and yield strengths exceeding 200 Newtons per square millimetre; (c) non-uniform internal bore; (d) not exceeding 167 millimetres in diameter Op. 05.08.2011 Dec. 19.12.2011 - TC 1126550 7304.23.00 DRILL PIPE, friction welded, having BOTH of the following: (a) quenched AND tempered grade SS 2225 M chromium molybdenum steel tool joints; (b) tool joint hardness NOT less than 320 HB and NOT greater than 340 HB Op. 07.02.2011 Dec. 09.05.2011 - TC 1105088 7304.23.00 DRILL PIPE, seamless, non-alloy carbon steel, circular cross section, having EITHER of the following: (a) outside diameter (OD) NOT greater than 168.3 mm; (b) wall thickness (WT) NOT less than 16 mm Op. 16.08.2010 Dec. 08.11.2010 - TC 1038045 7304.23.00 DRILL PIPES, WELLBORE, seamless, having BOTH of the following: (a) outside diameter (OD) NOT greater than 216 mm; (b) tool joint one end Op. 25.11.2009 Dec. 05.02.2010 - TC 0944896 7304.23.00 DRILL PIPES, having rotary connections attached, conforming to API Specification 7, being EITHER of the following: (a) conforming to API Specification 5D; (b) as listed in THE TABLE THE TABLE Outside Diameter Wall Thickness (i) 88 mm to 110 mm (both inclusive) 18 mm or greater; (ii) 110 mm to 120 mm (both inclusive) 20 mm or greater; (iii) 120 mm to 130 mm (both inclusive) 23 mm or greater Op. 01.01.2007 Dec. 09.11.2006 - TC 0614213 7304.23.00 DRILL RODS, FRICTION WELDED, having DIN 17MnV6 steel tool joints Op. 01.01.2007 Dec. 27.03.2007 - TC 0703471 7304.23.00 DRILL PIPE, conforming to American Petroleum Institute Item 50 applies unless otherwise stated. Tariff Description =========================================================================== Specification 5D:2001 (API 5D:2001), having rotary connection attached Op. 11.11.2008 Dec. 06.02.2009 - TC 0839269 7304.24.00 CASING AND/OR TUBING, STAINLESS STEEL, seamless Op. 10.04.2008 Dec. 04.07.2008 - TC 0803235 7304.29 CASING OR TUBING, oilwell (including casing or tubing with couplings), conforming to EITHER of the following: (a) API Specification 5CT; (b) Manufacturers" Material Specification CR9, CR13, CR22 or CR25 with other requirements to API Specifications 5CT, but NOT including EITHER of the following: (a) plain end casing or tubing; (b) casing with connectors Op. 01.07.1996 Dec. 06.06.1996 - TC 9605808 7304.29 JOINTS, blast, being tubing threaded at both ends, in nominal lengths of 3.05 m or 6.10 m Op. 01.07.1996 Dec. 16.05.1996 - TC 9608624 7304.29.00 CASING, OIL AND/OR GAS WELL, seamless, complying with American Petroleum Institute Standard 5L (API 5L), with OR without connectors, having an outside diameter NOT less than 300 mm and NOT greater than 380 mm Op. 05.08.2014 Dec. 24.11.2014 - TC 1427032 7304.29.00 CASING OR TUBING, OIL AND/OR GAS WELL, seamless, conforming to American Petroleum Institute Specification 5CT (API 5CT), with OR without connectors Op. 15.04.2013 Dec. 15.07.2013 - TC 1312751 7304.29.00 CASING, seamless, non alloy carbon steel, circular cross section, having EITHER of the following: (a) outside diameter (OD) NOT greater than 168.3 mm; (b) wall thickness (WT) NOT less than 16 mm, and complying with EITHER of the following: (a) American Society of Testing and Materials Standards A53/A53M - 07, grade B (ASTM A53/A53M - 07, grade B); (b) American Petroleum Institute Standard API specification 5L, grade X42 (API specification 5L, grade X42) Op. 13.08.2010 Dec. 08.11.2010 - TC 1037311 7304.29.00 CASING OR TUBING, OIL OR GAS WELL, seamless, plain end, diameter NOT exceeding 140 mm Op. 30.08.1999 Dec. 08.11.1999 - TC 9906606 7304.31 TUBE, seamless, cold drawn, having an outside diameter NOT exceeding 8 mm, an inside diameter NOT exceeding 4 mm, pressure rating NOT less than 54 900 kPa, to Specification DIN 2413 Op. 08.05.1989 Dec. 26.07.1990 - TC 8903168 7304.31 TUBES, heat exchange and condenser, seamless, cold drawn, carbon steel, in straight lengths, ends plain, bevelled or threaded BUT without further rework, to specification ASTM A179/A 179M-88a Op. 10.02.1992 Dec. 16.07.1992 - TC 9201981 7304.31 TUBES, seamless, cold drawn, in straight lengths, ends plain, bevelled or threaded, BUT without further rework, to specification DIN standard 2391: Part 2 Op. 10.02.1992 Dec. 16.07.1992 - TC 9202044 Item 50 applies unless otherwise stated. Tariff Description =========================================================================== 7304.31 TUBES, carbon steel, in straight lengths, ends plain, bevelled or threaded, BUT without further rework, conforming to ASTM A179, cold drawn, seamless, having an OD NOT less than 6.4 mm and NOT greater than 203.2 mm Op. 05.03.1992 Dec. 20.07.1992 - TC 9203132 7304.31 TUBES, (a) (b) (c) (d) (e) 7304.31.00 WELD TEST RINGS, complying with DNV-OS-F101 Op. 08.12.2005 Dec. 03.03.2006 cold drawn, seamless, to ANY of the following steel grades: K1006; K1016; K1010; K1020; K1026, or ANY of the following tube specifications: (a) JIS G3445 STKM 11-20; (b) BS6323:Part 6:1982; (c) ASTM A513, and having BOTH of the following: (a) carbon content NOT less than 0.06% and NOT greater than 0.4% by weight; (b) OD NOT less than 6.4 mm and NOT greater than 203.2 mm Op. 27.07.1992 Dec. 08.10.1992 - TC 9206994 - TC 0516769 7304.31.00 TUBES OR HOLLOW BARS, seamless, cold drawn in straight lengths Op. 26.11.1992 Dec. 08.03.1993 - TC 9210246 7304.31.00 SEAMLESS STEEL TUBE, ASTM A210 GR, comprising ALL of the following: (a) outside diameter NOT less than 38 mm; (c) wall NOT less than 2.6 mm; (d) length NOT less than 6 m and NOT greater than 8.3 m Op. 06.04.2004 Dec. 02.07.2004 - TC 0403598 7304.39 TUBES (NOT being honed tubes), seamless, having BOTH of the following: (a) elevated temperature properties conforming to Specification BS 3602 (1978) Grade 360 or AS 1835 TS 5; (b) OD NOT less than 1 250 mm OR a WT NOT exceeding 25 mm Op. 21.03.1985 Dec. 21.03.1985 - TC 8530426 7304.39 TUBES OR HOLLOW BARS (NOT being honed tubes), in straight lengths, ends plain, bevelled or threaded in accordance with ANY of the following tube, hollow bar or Pipe Material Specification options: (a) AS; (b) ASME; (c) ASTM; (d) BS; (e) DIN, but without further rework, having a length NOT less than four times the OD, as listed in THE TABLE THE TABLE Outside Diameter Wall Thickness (a) NOT exceeding 219.08 mm 13.00 mm or greater but NOT exceeding 25.00 mm; (b) 219.08 mm or greater but 12.70 mm or greater but NOT exceeding 254.00 mm NOT exceeding 50.80 mm; (c) 254.00 mm or greater but 19.05 mm or greater but NOT exceeding 323.85 mm NOT exceeding 41.00 mm; (d) 323.85 mm or greater but 25.40 mm or greater but NOT exceeding 720.73 mm NOT exceeding 75.00 mm Op. 01.01.1988 Dec. 01.01.1988 - TC 8735571 7304.39 TUBES, seamless, hot finished, boiler and superheater, in straight Item 50 applies unless otherwise stated. Tariff Description =========================================================================== lengths, ends plain, bevelled or threaded, BUT without further rework, to specification ASTM A210/A 210M-88a Op. 10.02.1992 Dec. 16.07.1992 - TC 9201980 7304.39 PIPE, seamless, hot finished, in straight lengths, ends plain, bevelled or threaded BUT without further rework, to specification ASTM A333/A333M-88a Op. 10.02.1992 Dec. 16.07.1992 - TC 9202042 7304.39.00 PROCESS PIPES, seamless, carbon steel, circular cross-section, having BOTH of the following: (a) square cut plain ends OR bevelled ends; (b) compliance with American Society for Testing and Materials standard ASTM A333/A333M - 10 Op. 21.08.2013 Dec. 11.11.2013 - TC 1328486 7304.39.00 PIPES, GYPSUM DEHYDRATION SYSTEM, iron OR non-alloy steel, having an external diameter greater than 380 mm Op. 23.11.2012 Dec. 03.04.2013 - TC 1245157 7304.39.00 7304.39.00 WELD TEST RINGS, complying with DNV-OS-F101 Op. 08.12.2005 Dec. 03.03.2006 - TC 0516768 LANCES, MONOLITHIC, INERT GAS, ceramic coated Op. 22.02.2007 Dec. 18.05.2007 - TC 0702193 7304.39.00 PIPES, STEEL, POWER STATION STEAM GENERATION BOILER, being ANY of the following: (a) main and/or auxilary steam pipes; (b) hot reheat pipes; (c) cold reheat pipes; (d) main feed water pipes; (e) super heater pipes Op. 31.08.2007 Dec. 09.11.2007 - TC 0713866 7304.39.00 HOLLOW BARS, seamless, hot rolled or hot finished in straight lengths Op. 22.10.1996 Dec. 06.01.1997 - TC 9611660 7304.39.00 TUBES, seamless, carbon steel, hot finished, in straight lengths, ends plain OR bevelled OR threaded, but without further rework, to specification DIN 1629 Op. 30.12.1996 Dec. 25.03.1997 - TC 9613286 7304.41 TUBES, stainless steel, containing 12% or more chromium, OD NOT exceeding 3.175 mm Op. 28.02.1984 Dec. 28.02.1984 - TC 8341367 7304.41 TUBES OR HOLLOW BARS (NOT being honed tubes), in straight lengths, ends plain, bevelled or threaded in accordance with ANY of the following tube, hollow bar or Pipe Material Specification options: (a) AS; (b) ASME; (c) ASTM; (d) BS; (e) DIN, but without further rework, having a length NOT less than four times the OD, as listed in THE TABLE: THE TABLE Outside Dia Wall Thickness (a) NOT exceeding 219.08 mm 13.00 mm or greater but NOT exceeding 25.00 mm; (b) 219.08 mm or greater but 12.70 mm or greater but Item 50 applies unless otherwise stated. Tariff Description =========================================================================== NOT exceeding 254.00 mm NOT exceeding 50.80 mm; (c) 254.00 mm or greater but 19.05 mm or greater but NOT exceeding 323.85 mm NOT exceeding 41.00 mm; (d) 323.85 mm or greater but 25.40 mm or greater but NOT exceeding 720.73 mm NOT exceeding 75.00 mm Op. 01.01.1988 Dec. 01.01.1988 - TC 8735572 7304.41 TUBES, alloy steel, in straight lengths, ends plain, bevelled or threaded in accordance with ANY of the following Pipe Material Specification options: (a) AS; (b) ASME; (c) ASTM; (d) BS; (e) DIN, but without further rework, containing NOT less than 12% by weight of chromium, having EITHER of the following: (a) OD NOT exceeding 105 mm and WT NOT less than 4.5 mm but NOT exceeding 25 mm; (b) OD NOT less than 105 mm and WT NOT exceeding 25 mm Op. 01.01.1988 Dec. 01.01.1988 - TC 8801453 7304.41 TUBES, seamless, stainless steel, plain square cut ends, minimum length 3 000 mm, to Specification ASTM A269, type 316L, having SI. surface finished: O.D. - bright annealed; I.D. - electro polished to RA.4um; or SU. surface finish: O.D. - bright annealed; I.D. - electro polished to RA.8um, in the following sizes: (a) 12.7 mm x 1.651 mm WT; (b) 19.05 mm x 1.651 mm WT; (c) 25.4 mm x 1.651 mm WT; (d) 38.1 mm x 1.651 mm WT; (e) 50.8 mm x 1.651 mm WT; (f) 63.5 mm x 1.651 mm WT; (g) 76.2 mm x 1.651 mm WT; (h) 101.6 mm x 2.108 mm WT; (i) 101.6 mm x 3.175 mm WT; (j) 152.4 mm x 5.004 mm WT Op. 07.10.1991 Dec. 19.02.1992 - TC 9108894 7304.41.00 TUBING, stainless steel, having ALL of the following: (a) welded threaded ends; (b) polytetrafluoroethylene (PTFE) seal; (c) hydrogenated nitrile butadiene rubber (HNBR) o-ring; (d) internal tube diameter of NOT less than 50 mm and NOT greater than 60 mm Op. 31.03.2014 Dec. 24.06.2014 - TC 1411122 7304.41.00 UMBILICALS, CHEMICAL INJECTION AND HYDRAULIC FLUID, SUBSEA, thermoplastic encapsulated, having a continuous length NOT less than 500 m Op. 05.02.2009 Dec. 08.05.2009 - TC 0903794 7304.41.00 WELD TEST RINGS, complying with DNV-OS-F101 Op. 08.12.2005 Dec. 03.03.2006 - TC 0516767 7304.41.00 TUBES, cold reduced, stainless steel, carbon content NOT exceeding 0.03%, to specifications ASTM A790, A789 Op. 16.07.1993 Dec. 01.11.1993 - TC 9306991 7304.41.00 TUBING, seamless stainless steel, duplex alloy S.A.F.2205 to ASTM A 789 UNS S31803, having an outside diameter less than 25mm Item 50 applies unless otherwise stated. Tariff Description =========================================================================== Op. 05.04.1993 Dec. 05.04.1993 - TC 9329022 7304.41.00 TUBE OR PIPE, stainless steel, to specification UNS S31803, having a chemical composition by weight of ALL the following: (a) carbon 0.030% maximum; (b) manganese 2.00% maximum; (c) phosphorus 0.030% maximum; (d) sulphur 0.020% maximum; (e) silicon 1.00% maximum; (f) chromium 21.00 - 23.00% both inclusive; (g) nickel 4.50 - 6.50% both inclusive; (h) nitrogen 0.03 - 0.20% maximum; (i) molybdenum 2.50 - 3.50% both inclusive Op. 25.05.1994 Dec. 26.08.1994 - TC 9404855 7304.41.00 TUBES, seamless, circular cross section, stainless steel, to specification ASTM A269 or ASTM A213, cold drawn and annealed, whether or NOT surface finished, having BOTH of the following: (a) OD NOT exceeding 6.35 mm; (b) WT NOT exceeding 1.20 mm Op. 31.07.1995 Dec. 27.10.1995 - TC 9509324 7304.41.00 TUBES OR PIPES, stainless steel, seamless Op. 25.11.2003 Dec. 08.03.2004 - TC 0314979 7304.49 TUBES, stainless steel, containing 12% or more chromium, OD NOT exceeding 3.175 mm Op. 01.01.1988 Dec. 01.01.1988 - TC 8635310 7304.49 TUBES, alloy steel, in straight lengths, ends plain, bevelled or threaded in accordance with ANY of the following Pipe Material Specification options: (a) AS; (b) ASME; (c) ASTM; (d) BS; (e) DIN, but without further rework, containing NOT less than 12% by weight of chromium, having EITHER of the following: (a) OD NOT exceeding 105 mm and WT 4.5 mm or greater but NOT exceeding 25.0 mm; (b) OD NOT less than 105 mm and WT NOT exceeding 25 mm Op. 03.07.1987 Dec. 04.09.1987 - TC 8734525 7304.49 TUBES OR HOLLOW BARS (NOT being honed tubes), in straight lengths, ends plain, bevelled or threaded in accordance with ANY of the following tube, hollow bar or Pipe Material Specification options: (a) AS; (b) ASME; (c) ASTM; (d) BS; (e) DIN, but without further rework, having a length NOT less than four times the OD, as listed in THE TABLE: THE TABLE Outside Dia Wall Thickness (a) NOT exceeding 219.08 mm 13.00 mm or greater but NOT exceeding 25.00 mm; (b) 219.08 mm or greater but 12.70 mm or greater but NOT exceeding 254.00 mm NOT exceeding 50.80 mm; (c) 254.00 mm or greater but 19.05 mm or greater but NOT exceeding 323.85 mm NOT exceeding 41.00 mm; (d) 323.85 mm or greater but 25.40 mm or greater but NOT exceeding 720.73 mm NOT exceeding 75.00 mm Item 50 applies unless otherwise stated. Tariff Description =========================================================================== Op. 01.01.1988 Dec. 01.01.1988 - TC 8735573 7304.49.00 TUBING OR PIPING, seamless stainless steel, having extruded aluminium finning Op. 20.07.2009 Dec. 02.10.2009 - TC 0925796 7304.49.00 WELD TEST RINGS, complying with DNV-OS-F101 Op. 08.12.2005 Dec. 03.03.2006 7304.49.00 - TC 0516766 HOLLOW BARS, stainless steel, grade 316L or 304L, wrought and fully annealed, in ANY of the following sizes: OUTSIDE DIAMETER (a) 118 mm (b) 125 mm (c) 125 mm (d) 132 mm (e) 140 mm (f) 150 mm (g) 150 mm (h) 170 mm (i) 180 mm (j) 190 mm (k) 200 mm (l) 212 mm (m) 224 mm (n) 236 mm Op. 08.03.1994 INSIDE DIAMETER 63 mm 71 mm 50 mm 71 mm 80 mm 95 mm 80 mm 118 mm 125 mm 132 mm 140 mm 130 mm 140 mm 150 mm Dec. 17.06.1994 - TC 9403562 7304.49.00 PIPES, stainless steel, seamless, bevelled OR plain ends Op. 29.07.1999 Dec. 15.10.1999 - TC 9905670 7304.49.00 TUBES OR PIPES, stainless steel, seamless Op. 25.11.2003 Dec. 08.03.2004 - TC 0314980 TUBES, longitudinally finned, extruded Op. 28.02.1984 Dec. 28.02.1984 - TC 8341428 7304.51 7304.51 PIPE, seamless, cold drawn, in straight lengths, ends plain, bevelled or threaded BUT without further rework, to specification ASTM A333/A 333M-88a Op. 10.02.1992 Dec. 16.07.1992 - TC 9202040 7304.51 PIPE, seamless, ferritic alloy steel, cold drawn, in straight lengths, ends plain, bevelled or threaded BUT without further rework, to specification ASTM A335/A 335M-89a Op. 10.02.1992 Dec. 16.07.1992 - TC 9202045 7304.51.00 TUBES, threaded, seamless, cold-drawn, having ALL of the following; (a) outside diameter NOT greater than 39 mm; (b) inside diameter NOT greater than 27.6 mm; (c) length NOT greater than 2.6 m Op. 19.05.2009 Dec. 14.08.2009 - TC 0916934 7304.51.00 WELD TEST RINGS, complying with DNV-OS-F101 Op. 08.12.2005 Dec. 03.03.2006 - TC 0516770 7304.51.00 TUBES, seamless alloy steel, cold drawn, compliant with American Society for Testing and Materials Standard A519/4130 (ASTM A519/4130) Op. 29.02.2008 Dec. 16.05.2008 - TC 0803409 7304.51.00 TUBES OR HOLLOW BARS, seamless, alloy steel, cold rolled or cold Item 50 applies unless otherwise stated. Tariff Description =========================================================================== finished, in straight lengths Op. 17.06.1993 Dec. 24.09.1993 - TC 9304563 7304.59 TUBES OR PIPES, seamless, tested and certified to EITHER of the following Specifications: (a) ASTM A200 Grade T5; (b) ASTM A335 Grade P5 Op. 01.01.1988 Dec. 01.01.1988 - TC 8801707 7304.59 TUBES, alloy steel, in straight lengths, ends plain, without further rework, to ANY of the following Material Specifications: (a) ASTM A213; (b) ASME A213; (c) BS 3059; (d) AS 1835, having ALL of the following: (a) chromium content, by weight, of 0.7% or greater but NOT exceeding 12.5%; (b) an OD of 30 mm or greater but NOT exceeding 127 mm; (c) WT NOT exceeding 12.5 mm Op. 16.10.1989 Dec. 02.01.1990 - TC 8907466 7304.59 TUBES, boiler, hot finished, seamless ferritic alloy steel, in straight lengths, ends plain, bevelled or threaded, BUT without further rework, to specification ASTM A213/A213M-89a Op. 10.02.1992 Dec. 23.07.1992 - TC 9201989 7304.59 PIPE, seamless ferritic alloy steel, hot finished, in straight lengths, ends plain, bevelled or threaded BUT without further rework, to specification ASTM A335/A 335M-88a Op. 10.02.1992 Dec. 16.07.1992 - TC 9201999 7304.59 PIPE, seamless, hot finished, in straight lengths, ends plain, bevelled or threaded BUT without further rework to specification ASTM A333/A 333M-88a Op. 10.02.1992 Dec. 16.07.1992 - TC 9202039 7304.59.00 PROCESS PIPES, seamless, carbon steel, circular cross-section, having BOTH of the following: (a) square cut plain ends OR bevelled ends; (b) compliance with American Society for Testing and Materials standard ASTM A 106/A 106M - 06a OR ASTM A106/A106M - 08 Op. 21.08.2013 Dec. 19.11.2013 - TC 1328488 7304.59.00 TUBES, seamless, alloy steel, forged, in straight lengths, having ALL of the following: (a) length NOT greater than 1 950 mm; (b) outside diameter (OD) NOT greater than 550 mm; (c) wall thickness (WT) NOT less than 70 mm Op. 17.11.2009 Dec. 22.01.2010 - TC 0943497 7304.59.00 WELD TEST RINGS, complying with DNV-OS-F101 Op. 08.12.2005 Dec. 03.03.2006 - TC 0516771 7304.59.00 PIPES, STEEL, POWER STATION STEAM GENERATION BOILER, being ANY of the following: (a) main steam pipes; (b) hot reheat pipes; (c) cold reheat pipes; (d) main feed water pipes Op. 28.12.2007 Dec. 24.05.2008 - TC 0800039 7304.59.00 RODS, RAISE DRILL, alloy steel, integral Op. 28.04.2008 Dec. 18.07.2008 Item 50 applies unless otherwise stated. - TC 0805489 Tariff Description =========================================================================== 7304.59.00 TUBES, seamless, carbon steel, hot finished in straight lengths, ends plain, bevelled or threaded, but without further rework, to specification AISI 4140 quenched and tempered Op. 09.12.1992 Dec. 30.08.1993 - TC 9310300 7304.59.00 BARS, hollow, to specification AISI 4145H modified Op. 18.04.1994 Dec. 22.07.1994 - TC 9404209 7304.59.00 TUBES OR PIPES, seamless, conforming to EITHER of the following specifications: (a) SA-213 T22; (b) SA-335 P22 Op. 01.11.1996 Dec. 31.01.1997 - TC 9611933 7304.59.00 DRILL STRING SECTIONS, THREADED, ROTARY PERCUSSIVE ROCK DRILLING, being ANY of the following: (a) hollow drill tube; (b) hollow bar and rod external cross section dimension exceeding 52 mm, and a maximum internal dimension greater than one half of the maximum external cross section dimension Op. 16.05.1997 Dec. 01.08.1997 - TC 9704455 7304.59.00 TUBES OR PIPES, seamless alloy steel, hot finished, to ASTM A519 Grade 4140 Op. 08.01.1998 Dec. 13.03.1998 - TC 9800163 7304.59.00 DRILL RODS, ROTARY PERCUSSIVE ROCK DRILLING, hollow, threaded OR tapered, external cross-section dimension exceeding 52 mm Op. 10.08.1998 Dec. 16.10.1998 - TC 9807063 7304.59.00 TUBES, hot rolled, seamless alloy steel to specification DIN1629 Op. 19.11.1999 Dec. 31.01.2000 - TC 9908842 7304.59.00 LANCES, OXYGEN OR INERT GAS, ceramic coated Op. 08.12.2000 Dec. 02.03.2001 - TC 0010030 7304.59.00 TUBES OR HOLLOW BARS, seamless, alloy steel, hot finished OR hot rolled, in straight lengths Op. 09.11.2004 Dec. 21.01.2005 - TC 0411761 7304.90.00 WELD TEST RINGS, complying with DNV-OS-F101 Op. 07.09.2005 Dec. 16.01.2006 - TC 0511817 7305.11.00 LINE PIPE, submerged arc welded, complying with ISO 3183-3, Grade L450, having BOTH of the following: (a) outside diameter greater than 1 400 mm; (b) wall thickness greater than 29 mm but NOT greater than 31 mm Op. 17.06.2005 Dec. 09.09.2005 - TC 0507512 7305.11.00 LINE PIPE, OIL AND GAS, complying with American Petroleum Institute (API) Standard, Specification 5L, Grade B, Production Specification Level (PSL) 1, having ALL of the following: (a) varnish coatings; (b) length NOT less than 12 metres; (c) bevelled ends; (d) wall thickness NOT less than 9 mm and NOT greater than 13 mm; (e) outside diameter NOT less than 640 mm and NOT greater than 800 mm; (f) longitudinally submerged arc welding; but NOT including spirally submerged arc welded steel line pipe Item 50 applies unless otherwise stated. Tariff Description =========================================================================== complying with Australian Standard AS 1579 Op. 10.04.2007 Dec. 12.09.2007 - TC 0705206 7305.11.00 PIPE, SUBMERGED ARC WELDED (SAW), having EITHER of the following: (a) outside diameter NOT less than 750 mm; (b) wall thickness NOT less than 9.53 mm Op. 27.08.2008 Dec. 09.02.2009 - TC 0828344 7305.11.00 LINE PIPE, submerged arc welded, to DNV-OS-F101 Op. 04.11.2004 Dec. 01.02.2005 7305.12.00 - TC 0411588 STEEL LINE PIPE, OIL AND/OR GAS WELL, ELECTRIC RESISTANCE WELDED, exceeding 406.4 mm external diameter, conforming to American Petroleum Institute Specification 5L (API 5L) Op. 20.07.2012 Dec. 08.11.2012 - TC 1241575 7305.12.00 LINE PIPE, ELECTRIC RESISTANCE WELDED (ERW), complying with American Petroleum Institute Standard Specification 5L (API 5L) Op. 20.07.2012 Dec. 10.10.2012 - TC 1224027 7305.12.00 LINE PIPE, ELECTRIC RESISTANCE WELDED(ERW), complying with American Petroleum Institute standard API Specification 5L, grade X65, having BOTH of the following: (a) outside diameter (OD) NOT less than 508 mm; (b) wall thickness (WT) NOT less than 19.1 mm Op. 14.04.2011 Dec. 11.07.2011 - TC 1112481 7305.12.00 PIPE, seamed, ERW, to specification API 5L Grade B, being EITHER of the following: (a) OD 609.6 mm, WT 9.5 mm; (b) OD 508 mm, WT 15.1 mm Op. 25.06.2010 Dec. 24.08.2010 - TC 1038781 7305.12.00 PIPE, ELECTRIC RESISTANCE WELDED, exceeding EITHER of the following: (a) outside diameter 508 mm; (b) wall thickness 12.7 mm Op. 20.02.2008 Dec. 18.03.2010 - TC 1013309 7305.12.00 LINE PIPE, OIL AND GAS PIPELINE, steel, having BOTH of the following: (a) diameter NOT less than 645 mm; (b) longitudinally welded Op. 23.04.2007 Dec. 16.07.2007 - TC 0705875 7305.12.00 LINE PIPE, OIL AND GAS, stainless steel, welded, having an external diameter NOT less than 406.4 mm Op. 31.07.2008 Dec. 24.10.2008 - TC 0824211 7305.12.00 LINE PIPE, electric resistance welded, to DNV-OS-F101 OR DEP 31.40.20.37 Op. 04.11.2004 Dec. 01.02.2005 - TC 0411589 7305.12.00 STEEL LINE PIPE, OIL AND/OR GAS WELL, ELECTRIC RESISTANCE WELDED, exceeding 406.4 mm external diameter, conforming to American Petroleum Institute Specification 5L (API 5L) Op. 20.07.2012 Dec. 08.11.2012 - TC 1241575 7305.19.00 PIPE SPOOLS, EXPANSION LOOP, stainless steel, having an outside diameter greater than 406.4 mm Op. 18.11.2013 Dec. 10.02.2014 - TC 1338995 7305.19.00 PIPE, SUBMERGED ARC WELDED (SAW), helical, having BOTH of the Item 50 applies unless otherwise stated. Tariff Description =========================================================================== following: (a) outside diameter NOT less than 750 mm; (b) wall thickness NOT less than 9.53 mm Op. 21.12.2011 Dec. 02.04.2012 - TC 1142287 7305.20.00 CASING, OIL AND/OR GAS WELL, ELECTRIC RESISTANCE WELDED, conforming to American Petroleum Institute Specification 5CT (API 5CT) with OR without connectors, external diameter exceeding 406.4 mm Op. 20.07.2012 Dec. 08.11.2012 - TC 1241578 7305.20.00 CASING, OIL AND/OR GAS WELL, electric resistance welded, conforming to American Petroleum Institute Specification 5CT (API 5CT), with OR without connectors Op. 20.07.2012 Dec. 31.10.2012 - TC 1241541 7305.20.00 CASING, OIL AND/OR GAS WELL, having BOTH of the following: (a) outside diameter NOT less than 500 mm; (b) wall thickness NOT less than 14 mm Op. 26.03.2012 Dec. 18.06.2012 - TC 1209900 7305.20.00 CASING, electric resistance welded, conforming to American Petroleum Institute Specification 5CT (API 5CT), Grades C-75 OR L-80 OR N-80 OR C-90 OR C-95 OR S-95 OR T-95 OR P-110 OR Q-125 OR V-150, with OR without connectors, having BOTH of the following: (a) nominal outside diameter NOT less than 508 mm; (b) wall thickness NOT less than 12.7 mm Op. 21.05.2010 Dec. 17.08.2010 - TC 1022968 7305.20.00 CONDUCTOR CASING, OILWELL, to API specification 5L, with OR without connectors, having BOTH of the following: (a) outside diameter exceeding 500 mm; (b) wall thickness exceeding 20 mm Op. 30.07.1998 Dec. 23.10.1998 - TC 9806755 7305.31 TUBES, alloy steel, in straight lengths, ends plain, bevelled or threaded in accordance with ANY of the following Pipe Material Specification options: (a) AS; (b) ASME; (c) ASTM; (d) BS; (e) DIN, but without further rework, containing NOT less than 10% by weight of chromium, having EITHER of the following: (a) OD NOT less than 1 250 mm; (b) WT 5 mm or greater but NOT exceeding 25 mm Op. 03.07.1987 Dec. 04.09.1987 - TC 8734523 7305.31.00 PIPES, electric resistance welded, circular cross-section, nonalloy steel, complying with Australian and New Zealand Standard 1163:2009 (AS/NZS 1163:2009), Grade C450L0, having ALL of the following: (a) length NOT less than 9 m and NOT greater than 18.15 m; (b) outside diameter 457 mm; (c) wall thickness NOT less than 5.2 mm and NOT greater than 11 mm; (d) bevelled ends; (e) non-alloy steel complying with Japanese Industrial Standard G 3474:2008 (JIS G 3474:2008), Grade STKT590 For the purposes of this Order, tolerances allowable for Item 50 applies unless otherwise stated. Tariff Description =========================================================================== specification (b) are +/- 5%. Op. 07.01.2014 Dec. 07.04.2014 - TC 1400827 7305.31.00 PIPES, mild steel OR stainless steel, with OR without couplings, having BOTH of the following: (a) internal ceramic tile lining; (b) outside diameter greater than 406.4 mm Op. 21.03.2011 Dec. 15.06.2011 - TC 1109648 7305.31.00 TUBES, stainless steel, straight seam welded, conforming to American Society of Testing and Materials Standards A-312/A 312M - 09 (ASTM A-312/A 312M - 09) and A358/A 358M - 08a (ASTM A358/A 358M - 08a), having ALL of the following: (a) straight lengths; (b) ends plain or bevelled or threaded or grooved; (c) wall thickness (WT) NOT less than 4 mm; (d) containing NOT less than 10% by weight of chromium Op. 01.07.2010 Dec. 29.09.2010 - TC 1029727 7305.31.00 WELD TEST RINGS, complying with Offshore Standard for Submarine Pipeline Systems DNV-OS-F101 Op. 08.12.2005 Dec. 08.03.2006 - TC 0604839 7305.39.00 WELD TEST RINGS, complying with DNV-OS-F101 Op. 08.12.2005 Dec. 03.03.2006 - TC 0516772 7306.19.00 LINE PIPE, ELECTRIC RESISTANCE WELDED (ERW), complying with American Petroleum Institute Standard Specification 5L (API 5L) and International Standard 3183,(ISO 3183), having a diameter exceeding 168.3 mm Op. 18.12.2012 Dec. 18.03.2013 - TC 1248298 7306.19.00 STEEL LINE PIPE, OIL AND/OR GAS WELL, ELECTRIC RESISTANCE WELDED, conforming to American Petroleum Institute Specification 5L (API 5L) having EITHER of the following: (a)external diameter NOT greater than 33.7 mm; (b)external diameter NOT less than 168.3 mm and NOT greater than 406.4 mm. Op. 15.11.2012 Dec. 17.12.2012 - TC 1248095 7306.19.00 LINE PIPE, ELECTRIC RESISTANCE WELDED (ERW), complying with American Petroleum Institute Standard Specification 5L (API 5L), having EITHER of the following: (a) diameter less than 33.7 mm; (b) diameter exceeding 168.3 mm Op. 20.07.2012 Dec. 12.11.2012 - TC 1224029 7306.19.00 PIPE, ELECTRIC RESISTANCE WELDED, exceeding a wall thickness of 12.7 mm Op. 22.02.2008 Dec. 20.11.2009 - TC 0943624 7306.19.00 TUBES OR HOLLOW BARS (NOT being honed tubes), in straight lengths, ends plain, bevelled or threaded in accordance with ANY of the following tube, hollow bar or Pipe Material Specification options: (a) AS; (b) ASME; (c) ASTM; (d) BS; (e) DIN, but without further rework, having a length NOT less than four times the OD, as listed in THE TABLE: THE TABLE Outside Dia Wall Thickness Item 50 applies unless otherwise stated. Tariff Description =========================================================================== (a) NOT exceeding 219.08 mm (b) 219.08 mm or greater but NOT exceeding 254.00 mm (c) 254.00 mm or greater but NOT exceeding 323.85 mm (d) 323.85 mm or greater but NOT exceeding 720.73 mm Op. 01.01.2007 Dec. 13.00 mm or greater but NOT exceeding 25.00 mm; 12.70 mm or greater but NOT exceeding 50.80 mm; 19.05 mm or greater but NOT exceeding 41.00 mm; 25.40 mm or greater but NOT exceeding 75.00 mm 09.11.2006 - TC 0614214 7306.19.00 PIPE, to specification API 5L Grade B, ASTM 53B, being ANY of the following sizes (+/- 10%): (a) OD 114.3 mm, WT 6.0 mm; (b) OD 88.9 mm, WT 5.5 mm; (c) OD 60.3 mm, WT 3.9 mm Op. 01.01.2007 Dec. 09.11.2006 - TC 0614217 7306.19.00 LINE PIPE, complying with DNV-OS-F101 Op. 01.01.2007 Dec. 02.01.2007 - TC 0614760 7306.19.00 PIPES, WELDED, complying with American Petroleum Institute Standard Specification of Line Pipe 5L, comprising ALL of the following: (a) outside diameter NOT less than 63 mm and NOT greater than 115 mm; (b) wall thickness NOT less than 4 mm and NOT greater than 11 mm; (c) yield strength capacity NOT less than 385 MPa Op. 26.02.2007 Dec. 18.05.2007 - TC 0703024 7306.19.00 TUBES OR PIPES, ERW, bevelled ends, certified to ALL the following specifications: (a) AS 1163; (b) API 5L grades B and X42; (c) ASTM A53 grade B; in ANY of the following sizes: Cross Section Diameter Wall Thickness Length NOT less than 88.5 mm and NOT less than 4 mm and NOT less than NOT greater than 90 mm NOT greater than 10 mm 6 m NOT less than 114 mm and NOT less than 4 mm and NOT less than NOT greater than 115 mm NOT greater than 10 mm 6 m NOT less than 141 mm and NOT less than 4 mm and NOT less than NOT greater than 142 mm NOT greater than 10 mm 6 m Op. 06.11.2003 Dec. 23.10.2008 - TC 0835803 7306.29.00 CASING, OIL AND/OR GAS WELL, ELECTRIC RESISTANCE WELDED, conforming to American Petroleum Institute Specification 5 CT (API 5CT), with OR without connector, having EITHER of the following: (a) external diameter NOT greater than 33.7 mm; (b) external diameter NOT less than 168.3 mm and NOT greater than 406.4 mm. Op. 15.11.2012 Dec. 17.12.2012 - TC 1248093 7306.29.00 CASING, OIL AND/OR GAS WELL, electric resistance welded, conforming to American Petroleum Institute Specification 5CT (API 5CT), with OR without connectors Op. 20.07.2012 Dec. 31.10.2012 - TC 1241536 7306.29.00 LINERS, OIL AND/OR GAS WELL, expandable, electric resistance welded Op. 13.05.2011 Dec. 08.08.2011 - TC 1115195 7306.29.00 TUBING, electrical resistance welded, coiled OR in spools, having Item 50 applies unless otherwise stated. Tariff Description =========================================================================== BOTH of the following: (a) minimum continuous length of 2 000 m; (b) minimum OD of 31 mm Op. 01.01.2007 Dec. 09.11.2006 - TC 0614219 7306.29.00 CASING, Electric Resistance Welded (ERW), complying with American Petroleum Institute 5CT (API 5CT) having BOTH of the following: (a) outside diameter of 406.4mm; (b) wall thickness exceeding 10 mm but NOT exceeding 14 mm For the purposes of this Order, tolerances of + or - 1% are allowable for the specification in (a) Op. 01.01.2007 Dec. 29.11.2006 - TC 0614773 7306.29.00 TUBES, electric resistance welded, having BOTH of the following: (a) outside diameter NOT greater than 50.8 mm; (b) external upset or non upset connections complying with American Petroleum Institute (API) Specification 5CT Op. 16.12.2008 Dec. 06.03.2009 - TC 0844063 7306.30 PIPES, lance, oxygen calorised and ceramic coated Op. 22.08.1991 Dec. 25.05.1992 - TC 9107706 7306.30 TUBES, ERW boiler, being EITHER carbon or carbon manganese steel, in straight lengths, ends plain, bevelled or threaded, BUT without further rework, to specification ASTM A178/A 178M-89 Op. 10.02.1992 Dec. 16.07.1992 - TC 9201983 7306.30 TUBES, cold drawn, welded, to specification ASTM A513, having BOTH of the following: (a) OD NOT less than 203.2mm and NOT greater than 306.0mm; (b) carbon content NOT less than 0.06% and NOT greater than 0.4% by weight Op. 04.09.1992 Dec. 31.12.1992 - TC 9208087 7306.30.00 COILED TUBING, OIL AND GAS WELL, whether OR not on spools AND/OR reels Op. 20.12.2013 Dec. 20.03.2014 - TC 1409618 7306.30.00 PIPES, welded, circular cross-section, non-alloy steel, complying with Australian/New Zealand Standard AS/NZS 1163:2009, Grade C450L0, having ALL of the following: (a) length NOT less than 9 m and NOT greater than 18 m; (b) pipe diameter NOT less than 273 mm and NOT greater than 457 mm; (c) pipe wall thickness NOT less than 4.5 mm and NOT greater than 13 mm; (d) non-alloy steel complying with Japanese Industrial Standard JIS G 3474:2008, Grade STKT590 Op. 16.05.2012 Dec. 06.08.2012 - TC 1216161 7306.30.00 TUBES, non-alloy steel, welded, circular cross section, complying with American Society for Testing and Materials standard ASTM A214/A214M-96(2005), having ALL of the following: (a) carbon content NOT greater than 0.18%; (b) manganese content NOT less than 0.27% and NOT greater than 0.63%; (c) outside diameter NOT less than 24.13 mm and NOT greater than 26.7 mm; (d) wall thickness NOT less than 2.05 mm and NOT greater than 2.27 mm; (e) length NOT less than 10 m; (f) heat treated at NOT less than 900 degrees Celsius; (g) straight lengths Item 50 applies unless otherwise stated. Tariff Description =========================================================================== Op. 03.11.2011 Dec. 23.01.2012 - TC 1136709 7306.30.00 PIPES, mild steel, with OR without couplings, having BOTH of the following: (a) internal ceramic tile lining; (b) outside diameter less than 406.4 mm Op. 28.02.2011 Dec. 06.06.2011 - TC 1107493 7306.30.00 PIPES, welded steel, multilayer, having ALL of the following: (a) steel inner service pipe; (b) polyurethane foam insulation incorporating copper wires; (c) high density polyethylene outer casing Op. 07.06.2010 Dec. 30.08.2010 - TC 1025391 7306.30.00 TUBES, welded, complying with Japanese Industrial Standard G3445 STK11A (JIS G3445 STKM11A), having an outside diameter NOT greater than 12 mm Op. 07.02.2007 Dec. 20.04.2007 - TC 0701959 7306.30.00 TUBES, cold drawn, welded to specification DIN 2393, having BOTH of the following: (a) carbon content NOT less than 0.06% and NOT greater than 0.4% by weight; (b) outside diameter NOT less than 6.4 mm and NOT greater than 203.2 mm Op. 28.06.1995 Dec. 29.09.1995 - TC 9508551 7306.30.00 TUBES OR PIPES, ERW, conforming to specification SA 178 Op. 01.11.1996 Dec. 20.01.1997 - TC 9611935 7306.30.00 TUBES, cold drawn, welded, stress relieved, to DIN specification 2393, having ALL of the following: (a) outside diameter of 15 mm to 22 mm; (b) inside diameter of 13 mm to 19 mm; (c) wall thickness of 1 mm to 1.6 mm Op. 16.04.2002 Dec. 05.07.2002 - TC 0203211 7306.30.00 TUBES, WELDED, non alloy steel, being EITHER of the following: (a) single wall resistance welded to specification SAE J526, having ALL of the following: (i) carbon content NOT greater than 0.13%; (ii) outside diameter NOT greater than 11.50 mm; (iii) wall thickness NOT less than 0.5 mm and NOT greater than 1.0 mm; (b) double wall copper brazed to specification SAE J527, having ALL of the following: (i) carbon content NOT greater than 0.13%; (ii) outside diameter NOT greater than 13 mm; (iii) wall thickness NOT less than 0.5 mm and NOT greater than 1.0 mm Op. 31.03.2003 Dec. 27.06.2003 - TC 0303383 7306.40 TUBES, stainless steel, longitudinally welded, having BOTH of the following dimensions: (a) an OD 105 mm or greater but NOT exceeding 220 mm; (b) a WT 1.50 mm or greater but NOT exceeding 5.00 mm Op. 30.04.1985 Dec. 05.09.1985 - TC 8531977 7306.40 TUBES, alloy steel, in straight lengths, ends plain, bevelled or threaded in accordance with ANY of the following Pipe Material Specification options: (a) AS; (b) ASME; (c) ASTM; Item 50 applies unless otherwise stated. Tariff Description =========================================================================== (d) BS; (e) DIN, but without further rework, containing NOT less than 12% by weight of chromium, having EITHER of the following: (a) OD NOT exceeding 105 mm and WT 4.5 mm or greater but NOT exceeding 25.0 mm; (b) OD NOT less than 105 mm and WT NOT exceeding 25 mm Op. 01.01.1988 Dec. 01.01.1988 - TC 8733276 7306.40.00 PRESSURE TUBING, stainless steel, wound on spools OR reels, having ALL of the following: (a) wall thickness NOT greater than 1.70 mm; (b) outer diameter NOT greater than 14.00 mm; (c) fluorinated ethylene propylene (FEP) protective outer pipe cover Op. 27.08.2014 Dec. 17.11.2014 - TC 1430285 7306.40.00 HYDRAULIC CONTROL LINES, OIL AND/OR GAS WELL EQUIPMENT, wound on spools OR reels, including BOTH of the following: (a) NOT less than 2 stainless steel pipes, having BOTH of the following: (i) pipe wall thickness NOT greater than 1.36 mm; (ii) pipe outer diameter NOT less than 5.70 mm and NOT greater than 6.90 mm, (b) ethylene tetrafluoroethylene (ETFE) protective cover Op. 20.06.2014 Dec. 10.09.2014 - TC 1421009 7306.40.00 TUBES OR PIPES, stainless steel, longitudinal welded, in straight lengths, conforming to EITHER of the following specifications: (a) American Society for Testing and Materials (ASTM) specifications A249 OR A268 OR A269 OR A270 OR A554 OR A688 OR A789; (b) Australian Standard 1528 (AS 1528) Op. 06.02.2014 Dec. 05.05.2014 - TC 1405087 7306.40.00 TUBES OR PIPES, stainless steel, welded, in straight lengths, conforming to ANY of the following American Society for Testing and Materials (ASTM) specifications: (a) A312; (b) A358; (c) A409; (d) A778; (e) A790; (f) A813; (g) A814; (h) A928; (i) A999 Op. 23.12.2013 Dec. 17.03.2014 - TC 1342173 7306.40.00 PIPES, stainless steel, having ALL of the following: (a) outside diameter NOT less than 10.3 mm and NOT greater than 406.4 mm; (b) wall thickness NOT less than 1.24 mm and NOT greater than 33.32 mm; (c) compliance with American Society for Testing and Materials standards Designations: ASTM A269-10 OR ASTM A312/A312M - 11 OR ASTM A554-13 Op. 03.10.2013 Dec. 13.01.2014 - TC 1333366 7306.40.00 TUBES AND/OR PIPES, stainless steel, longitudinal welded, rolled seam, having ALL of the following: (a) outside diameter NOT less than 10 mm and NOT greater than 219 mm; Item 50 applies unless otherwise stated. Tariff Description =========================================================================== (b) wall thickness NOT less than 1 mm and NOT greater than 2.6 mm; (c) conforming to American Iron and Steel Institute specifications 304 OR 316L (AISI 304 OR AISI 316L) Op. 08.07.2013 Dec. 02.10.2013 - TC 1323026 7306.40.00 PIPES, stainless steel, with OR without couplings, having BOTH of the following: (a) internal ceramic tile lining; (b) outside diameter less than 406.4 mm Op. 21.03.2011 Dec. 15.06.2011 - TC 1109650 7306.40.00 UMBILICALS, CHEMICAL INJECTION, SUBSEA, thermoplasticencapsulated tubes Op. 17.06.2005 Dec. 09.09.2005 - TC 0507509 7306.40.00 WELD TEST RINGS, complying with DNV-OS-F101 Op. 08.12.2005 Dec. 03.03.2006 - TC 0516775 7306.40.00 TUBES OR PIPES, stainless steel, to specification UNS S31803, having chemical composition by weight of ALL the following: (a) carbon : 0.030% maximum; (b) manganese : 2.00% maximum; (c) phosphorus : 0.030% maximum; (d) sulphur : 0.020% maximum; (e) silicon : 1.00% maximum; (f) chromium : 21.00 - 23.00% both inclusive; (g) nickel : 4.50 - 6.50% both inclusive; (h) nitrogen : 0.03 - 0.20% maximum; (i) molybdenum : 2.50 - 3.50% both inclusive Op. 06.06.1994 Dec. 09.09.1994 - TC 9405021 7306.50.00 TUBES, ERW, aluminized, type JIS G3445, having ALL of the following: (a) 12.7 mm OD; (b) 1.6 mm WT; (c) 5 700 mm mill length Op. 14.04.1994 Dec. 29.07.1994 - TC 9404172 7306.61.00 TUBES, square OR rectangular, electric resistance welded, complying with Australian/New Zealand Standard 1163:2009 (AS/NZS 1163:2009), Grade C350L0 OR C450L0, with a perimeter NOT less than 950 mm and having EITHER (a) OR (b) as follows: (a) silicon content plus 2.5 times the phosphorus content NOT greater than 0.09%; (b) silicon content greater than 0.14% and NOT greater than 0.24% Op. 26.09.2014 Dec. 14.11.2014 - TC 1439520 7306.61.00 TUBES OR PIPES, stainless steel, square OR rectangular cross section, longitudinal welded in straight lengths, conforming to American Society for Testing and Materials A554 (ASTM A554) specification Op. 06.02.2014 Dec. 05.05.2014 - TC 1405088 7306.61.00 TUBES, square OR rectangular, electric resistance welded, complying with Australian/New Zealand Standard 1163:2009 (AS/NZS 1163:2009), Grade C350L0 OR C450L0, having EITHER (a) OR (b) AND (c), as follows: (a) silicon content plus 2.5 times the phosphorus content NOT greater than 0.09%; (b) silicon content greater than 0.14% and NOT greater than 0.24%; (c) perimeter NOT less than 950 mm Op. 24.01.2014 Dec. 21.03.2014 - TC 1410116 Item 50 applies unless otherwise stated. Tariff Description =========================================================================== 7306.61.00 COLUMNS AND/OR BEAMS, hollow OR square OR rectangular shape, steel, complying with Australian/New Zealand Standard 1163:2009 grade C450L0 (AS/NZS 1163:2009 grade C450L0), having BOTH of the following: (a) silicon content NOT greater than 0.06%; (b) in EITHER of the following sizes: (i) outside perimeter NOT less than 950 mm; (ii) outside perimeter NOT less than 370 mm and thickness NOT less than 8.1 mm Op. 20.09.2013 Dec. 16.12.2013 - TC 1332191 7306.61.00 DUCTS, GYPSUM DEHYDRATION SYSTEM, iron OR steel, having an external diameter greater than 900 mm Op. 23.11.2012 Dec. 03.04.2013 - TC 1245145 7306.61.00 TUBES, rectangular, stainless steel, NOT less than 100 mm x 50 mm across the flat dimensions Op. 01.01.2007 Dec. 09.11.2006 - TC 0614222 7306.61.00 TUBES, square, stainless steel, NOT less than 100 mm x 100 mm across the flat dimension Op. 01.01.2007 Dec. 09.11.2006 - TC 0614223 7306.61.00 TUBES, cold drawn, carbon steel, hollow frame profile, having ANY of the following sectional dimensions: Length Width Wall Thickness (a) 90 mm 41 mm 2.0 mm; (b) 104 mm 43 mm 2.5 mm; (c) 104 mm 43 mm 3.0 mm Op. 01.01.2007 Dec. 08.05.2007 - TC 0705890 7306.61.00 TUBES, square or rectangular, stainless steel to grade 1.4003, having BOTH of the following: (a) width NOT greater than 105 mm; (b) wall thickness NOT greater than 4 mm Op. 22.10.2008 Dec. 27.02.2009 - TC 0836453 7306.69.00 TUBES OR PIPES, stainless steel, longitudinal welded in straight lengths, conforming to American Society for Testing and Materials A554 (ASTM A554) specification, being ANY of the following cross sections: (a) oval; (b) slotted; (c) triangular; (d) D section; (e) tear drop Op. 06.02.2014 Dec. 05.05.2014 - TC 1405089 7306.69.00 TUBES, cold drawn, carbon steel, hollow frame profile, having ANY of the following sectional dimensions: Length Width Wall Thickness (a) 90 mm 41 mm 2.0 mm; (b) 104 mm 43 mm 2.5 mm; (c) 104 mm 43 mm 3.0 mm Op. 01.01.2007 Dec. 08.05.2007 - TC 0705891 7307.11.00 FITTINGS, TUBE AND PIPE, rolled grooved, galvanised OR painted, with OR without gaskets, being ANY of the following: (a) elbows; (b) couplings; (c) reducers; (d) adaptors; (e) tees; Item 50 applies unless otherwise stated. Tariff Description =========================================================================== (f) caps; (g) crosses; (h) reducing tees; (i) grooved flanges; (j) adaptor flanges Op. 19.08.2014 Dec. 10.11.2014 - TC 1429119 7307.11.00 FITTINGS, TEE SHAPED, TUBE OR PIPE JOINT, iron, threaded, galvanised OR painted, including ALL of the following: (a) outlet housing, with OR without gaskets; (b) bolts AND/OR U shaped bolts; (c) nuts Op. 19.08.2014 Dec. 10.11.2014 - TC 1429120 7307.11.00 FITTINGS, being elbows OR tees, galvanised, rolled grooved, ductile cast iron Op. 10.12.2009 Dec. 26.02.2010 - TC 0948291 7307.11.00 FITTINGS, PIPE, cast iron, non-combustible, non-flammable, complying with European Standard EN 877:1999 (EN 877:1999) Op. 13.10.2006 Dec. 22.12.2006 - TC 0615826 7307.11.00 COUPLINGS, CLAW, cast iron Op. 22.04.2008 Dec. 18.07.2008 - TC 0804812 7307.11.00 FITTINGS, ELBOWS AND/OR TEES, painted roll, grooved Op. 09.09.2008 Dec. 28.11.2008 - TC 0830239 7307.19 FITTINGS, pipe, buttweld, socketweld or threaded, being EITHER of the following: (a) manufactured from ASTM A-216 WCB carbon steel castings; (b) manufactured from ASTM A-148 GR 60-90 steel castings Op. 18.02.1985 Dec. 23.07.1985 - TC 8530530 7307.19.00 FITTINGS, PIPE AND/OR TUBE, malleable cast iron, reducing OR nonreducing, being ANY of the following: (a) tees; (b) combination tees and crosses; (c) corners; (d) crosses; (e) cross sets; (f) crossovers; (g) elbows; (h) flanges; (i) sockets; (j) side palms; (k) supports; (l) swivels; (m) couplings; (n) hooks; (o) collars; (p) collar plates; (q) hinges; (r) panel clips; (s) bases; (t) base plates Op. 29.09.2010 Dec. 20.12.2010 - TC 1044234 7307.19.00 FITTINGS, PIPE, ductile cast iron Op. 10.04.2008 Dec. 20.06.2008 7307.19.00 - TC 0803227 FITTINGS, CAMLOCK, stainless steel, being ANY of the following: (a) male sections and/or female sections; (b) plugs; Item 50 applies unless otherwise stated. Tariff Description =========================================================================== (c) caps Op. 22.04.2008 Dec. 18.07.2008 - TC 0804811 7307.19.00 COUPLINGS, flexible, cast, stainless steel, having internal rubber gaskets Op. 29.10.2008 Dec. 16.01.2009 - TC 0837499 7307.19.00 PIPE FITTINGS, roll grooved or shouldered, being ANY of the following: (a) elbows; (b) tees; (c) reducers; (d) end caps; (e) adapters Op. 04.12.2008 Dec. 27.02.2009 - TC 0842803 7307.19.00 FITTINGS, pipe, malleable cast iron Op. 28.04.1993 Dec. 30.07.1993 - TC 9305440 7307.19.00 FITTINGS, pipe, B.S.P thread, made of galvanised malleable iron, to BS 1256, being ANY of the following: (a) elbows, 90 degrees, being EITHER, female to female, or male to female; (b) elbows, 45 degrees, being female to female; (c) elbows, 3 way; (d) elbows, reducing, 90 degrees; (e) tees, including 4 way, and reducing tees; (f) bush, hexagon; (g) caps; (h) crosses; (i) backnuts; (j) nipples, being ANY of the following: (i) hexagon; (ii) barrel; (iii) plain; (iv) reducing; (k) sockets including reducing sockets; (l) plugs, square head; (m) bends, 90 degrees, EITHER, male to female, or female to female; (n) bends, 45 degrees, male to female; (o) unions, EITHER, male to female, or female to female Op. 06.07.1993 Dec. 08.10.1993 - TC 9306802 7307.19.00 PIPE FITTINGS, POTABLE WATER AND GAS LINES, being EITHER of the FOLLOWING: (a) malleable cast iron couplings, incorporating a rubber seal and washer (b) tapped OR non tapped plugs incorporating a rubber seal Op. 23.05.1996 Dec. 06.09.1996 - TC 9607790 7307.21.00 FLANGES, STAINLESS STEEL PIPE, including internal alumina ceramic tiles Op. 28.02.2011 Dec. 23.05.2011 - TC 1107490 7307.21.00 FLANGES, PIPE, stainless steel, seamless Op. 29.07.1999 Dec. 15.10.1999 - TC 9905666 7307.22.00 FITTINGS, TUBE, stainless steel, with OR without seals, being threaded bends Op. 31.03.2010 Dec. 09.07.2010 - TC 1015482 7307.22.00 FITTINGS, VACUUM, stainless steel, operating pressure lower than 133 x 0.0000001 MPa, being EITHER of the following: Item 50 applies unless otherwise stated. Tariff Description =========================================================================== (a) couplings; (b) elbows Op. 18.12.1997 Dec. 27.02.1998 - TC 9711204 7307.23 BENDS, CROSSES, ELBOWS OR TEES, buttweld, stainless steel, conforming dimensionally to ANY of the following Specifications: (a) BS 1640; (b) ANSI B16.9; (c) ANSI B16.28 Op. 28.02.1984 Dec. 28.02.1984 - TC 8341312 7307.23 FITTINGS, stainless steel, tube or pipe, buttweld, annealed, internally polished Op. 23.11.1987 Dec. 23.02.1989 - TC 8735514 7307.23 FITTINGS, seamless, stainless steel grade 316L, to specification ASTM 269 or ASTM 270, electropolished internally through entire length Op. 20.05.1988 Dec. 02.05.1989 - TC 8805455 7307.23.00 CONNECTOR HUBS, PIPE CLAMP, stainless steel, with OR without seals Op. 17.06.2014 Dec. 10.09.2014 - TC 1420343 7307.23.00 REDUCERS, seamless, butt weld, stainless steel Op. 26.10.2012 Dec. 07.01.2013 - TC 1241137 7307.29 RINGS, gasket or packing, to API Specification 6A, capable of operating at temperatures of 125 degrees C or greater Op. 30.12.1987 Dec. 27.04.1988 - TC 8733301 7307.29.00 CONNECTOR HUBS, PIPE CLAMP, stainless steel, with OR without seals Op. 17.06.2014 Dec. 01.09.2014 - TC 1420587 7307.29.00 STAB PLATES, SUBSEA, stainless steel, having NOT less than 8 connection points Op. 25.02.2013 Dec. 02.05.2013 - TC 1306853 7307.29.00 COUPLINGS, PIPE, compression, stainless steel, having ALL of the following: (a) inside diameter NOT less than 200 mm; (b) single sealing sleeve consisting of a single sealing lip on each side with progressive sealing effect; (c) single radial positioned locking system with 1 OR 2 OR 3 screws Op. 26.07.2012 Dec. 22.10.2012 - TC 1227050 7307.29.00 CONNECTORS, STAB, SUBSEA, male AND/OR female, with OR without protective caps Op. 15.05.2012 Dec. 06.08.2012 - TC 1215919 7307.29.00 FITTINGS, DRAINAGE, Grade 316L stainless steel, being ANY of the following: (a) filter baskets; (b) removable water traps; (c) grates; (d) drainage bowls, having a diameter NOT greater than 300 mm Op. 24.09.2010 Dec. 20.12.2010 - TC 1043685 7307.29.00 FITTINGS, TUBE, stainless steel, with OR without seals, being ANY of the following: (a) couplings having a diameter NOT greater than 200 mm; (b) reducers; Item 50 applies unless otherwise stated. Tariff Description =========================================================================== (c) bends; (d) T junctions; (e) union connectors; (f) adapters Op. 29.04.2010 Dec. 09.07.2010 - TC 1019464 7307.29.00 FITTINGS, PIPE AND TUBE, Grade 316L stainless steel, push fit, with or without seal, being ANY of the following: (a) pipe incorporating a socket; (b) bends; (c) pipe, having NOT less than 45 degree junctions and NOT greater than 90 degree junctions; (d) double sockets; (e) "P" traps; (f) bottle trap; (g) eccentric increasers; (h) eccentric reducers; (i) access bends; (j) threaded adaptor Op. 25.02.2010 Dec. 14.05.2010 - TC 1009883 7307.29.00 FITTINGS, DRAINAGE, Grade 316L stainless steel, being ALL of the following: (a) filter baskets; (b) removable water traps; (c) grates Op. 25.02.2010 Dec. 14.05.2010 - TC 1009880 7307.29.00 FITTINGS, PIPE AND TUBE, stainless steel, being ANY of the following: (a) sealing rings; (b) bodies; (c) cap nuts; (d) weld cones; (e) flare adaptors Op. 11.03.2009 Dec. 06.11.2009 - TC 0941426 7307.29.00 FITTINGS, CAMLOCK, being ANY of the following: (a) male sections and/or female sections; (b) plugs; (c) caps Op. 20.12.2007 Dec. 07.03.2008 - TC 0710840 7307.29.00 FITTINGS, COUPLING, HOSE, quick connect, being ANY of the following; (a) male sections; (b) female sections; (c) lever rings; (d) male plugs; (e) female caps Op. 21.12.2007 Dec. 07.03.2008 - TC 0721937 7307.29.00 COUPLINGS, HOSE, quick connect, comprising ALL of the following: (a) male sections; (b) female sections; (c) lever rings Op. 21.12.2007 Dec. 14.03.2008 - TC 0721940 7307.29.00 FITTINGS, ROOF DRAINAGE, stainless steel, being ANY of the following: (a) rainwater outlets; (b) hoppers; (c) elbows; (d) s-curves; Item 50 applies unless otherwise stated. Tariff Description =========================================================================== (e) pipe flaps including sets of 2 or more of the above Op. 14.10.2008 Dec. 14.01.2009 - TC 0835301 7307.29.00 COUPLINGS, camlocking, to material 316 stainless steel, 15 mm to 200 mm, inclusive of both adaptors (male) and couplers (female). Op. 13.08.1993 Dec. 10.02.1994 - TC 9307389 7307.29.00 JOINTS, swivel, stainless steel, v-ring type, pressure rating greater than 6 800 KPa Op. 14.06.1993 Dec. 23.09.1993 - TC 9314494 7307.29.00 FITTINGS, pipe, forged stainless steel to specification type F 51 ASTM UNS S 31803, having the surface descaled by turning Op. 27.05.1994 Dec. 02.09.1994 - TC 9404892 7307.29.00 FITTINGS, vacuum, stainless steel, helium leak tested, rated to lower than 133 x 10 -7 MPa, being ANY of the following: (a) plug; (b) cap; (c) gland; (d) body; (e) female nut; (f) male nut; (g) bodies, assembled with nuts and ferrules; (h) assemblies including ANY of the above Op. 22.05.1997 Dec. 15.08.1997 - TC 9704622 7307.29.00 COUPLINGS, FLOW, OIL AND GAS WELL, stainless steel Op. 15.12.1997 Dec. 27.02.1998 - TC 9711103 7307.91.00 FLANGES, STEEL PIPE, including internal alumina ceramic tiles Op. 28.02.2011 Dec. 30.05.2011 - TC 1107491 7307.91.00 FLANGES, DOWNTAKE PIPE, WALKING BEAM FURNACE, being ANY of the following: (a) DN 200; (b) DN 300; (c) DN 350; (d) DN 400 Op. 25.11.2005 Dec. 13.02.2006 - TC 0516608 7307.91.00 FLANGES, PIPE, being ANY of the following: (a) weld neck flanges; (b) blind flanges; (c) spectacle blind flanges; (d) slip on flanges; (e) socket weld flanges; (f) threaded flanges; (g) bulkhead flanges Op. 20.02.2008 Dec. 02.05.2008 - TC 0803404 7307.91.00 FLANGE ADAPTERS, PIPE OR TUBE OR HOSE, carbon steel, with or without seal Op. 03.12.2008 Dec. 27.02.2009 - TC 0842547 7307.91.00 FLANGES, HOT FORGED, SEAMLESS, comprising ALL of the following: (a) inner diameter NOT less than 1 500 mm; (b) width NOT greater than 400 mm; (c) outer diameter NOT less than 2 000 mm Op. 09.10.2003 Dec. 03.03.2004 - TC 0312809 7307.92.00 FITTINGS, TUBE, carbon steel, press fit, with OR without seals, being threaded bends having an internal AND/OR external zinc Item 50 applies unless otherwise stated. Tariff Description =========================================================================== 7307.92.00 coating NOT greater than 8 micron Op. 18.10.2010 Dec. 13.01.2011 - TC 1046727 ELBOWS, threaded Op. 08.10.2008 - TC 0834585 Dec. 14.01.2009 7307.92.00 FITTINGS AND ADAPTORS, PIPE OR TUBE OR HOSE, carbon steel, with or without seal, being ANY of the following: (a) elbows, 90 degrees; (b) elbows, 45 degrees; (c) elbows, 3 way tees, being either male to female OR combinations of both; (d) tube sleeves; (e) bends, 90 degrees; (f) bends, 45 degrees Op. 03.12.2008 Dec. 27.02.2009 - TC 0842548 7307.92.00 FITTINGS, pipe, steel, complying with standards BS1740 or AS3672 Op. 10.05.1994 Dec. 19.08.1994 - TC 9404635 7307.92.00 FITTINGS, PIPE AND TUBE, including sealing rings, bodies, nuts and weld cones, having BOTH of the following: (a) compliance with pressure rating of either LL, L or S to DIN 2353; (b) interchangeability of the whole or any component of the fitting with other fittings or components which comply with the dimensional specifications set out in DIN 2353, but NOT including ANY of the following: (a) stainless steel fittings; (b) twin ferrule fittings Op. 03.11.1995 Dec. 09.02.1996 - TC 9511750 7307.92.00 FITTINGS, TUBE, elbow, carbon steel, twin ferrule Op. 18.11.1997 Dec. 23.01.1998 - TC 9710155 7307.93 FITTINGS, buttweld, in accordance with Dimensional Specification MSS-SP75 and Material Specification API 5LX Op. 28.02.1984 Dec. 28.02.1984 - TC 8341295 7307.93 FITTINGS, buttweld pipe, being ANY of the following: (a) to ASTM Specification A420 GRWPL6: (i) elbows, 45 degrees; (ii) elbows, 90 degrees, OD NOT exceeding 304.8 mm; (iii) reducers, eccentric; (b) to ASTM Specification A234 GRWP1: (i) elbows, 45 degrees or 90 degrees, OD NOT exceeding 254 mm; (ii) reducers, eccentric, OD at larger end NOT exceeding 254 mm Op. 28.02.1984 Dec. 28.02.1984 - TC 8341297 7307.93 FITTINGS, being ANY of the following: (a) elbows to ASTM Specification A234 WPB, having a dia less than 406.4 mm OD; (b) reducers to ASTM Specification A234 WPB, having BOTH diameters less than 406.4 mm OD; (c) elbows, reducers or tees to ASTM Specification A234 WP 11 Op. 19.10.1987 Dec. 21.12.1987 - TC 8735075 7307.93 JOINTS, insulating, monobloc or monolithic Op. 01.01.1988 Dec. 01.01.1988 7307.93.00 - TC 8803112 CONNECTOR HUBS, PIPE CLAMP, carbon steel, with OR without seals Op. 17.06.2014 Dec. 10.09.2014 - TC 1420583 Item 50 applies unless otherwise stated. Tariff Description =========================================================================== 7307.93.00 FITTINGS, PIPE AND/OR TUBE, butt weld, being caps of carbon steel to American Society of Testing and Materials Specification A234 Grade WPB (ASTM A234 Grade WPB) Op. 21.10.2010 Dec. 10.01.2011 - TC 1047333 7307.93.00 PARTS, BOILER INSPECTION BUTTWELD FITTINGS, being EITHER of the following: (a) butt weld hubs; (b) blind hubs Op. 03.02.2010 Dec. 23.04.2010 - TC 1005997 7307.93.00 FITTINGS, BUTTWELD, STEEL PIPE OR TUBE, having ALL of the following: (a) inspection cap; (b) clamp assembly consisting of BOTH of the following: (i) clamp segments; (ii) studs and nuts, (c) seal ring; (d) butt welding hub Op. 15.12.2009 Dec. 05.03.2010 - TC 0948886 7307.93.00 FITTINGS, PIPE OR TUBE, butt-welded, forged steel, being reinforced and contoured connections Op. 28.07.2009 Dec. 16.10.2009 - TC 0927139 7307.93.00 FITTINGS, PIPE AND/OR TUBE, butt weld, alloy steel, being end caps Op. 28.07.2009 Dec. 09.10.2009 - TC 0927136 7307.93.00 INDUCTION BENDS, LINE PIPE, with or without concrete coating, with or without internal corrosion resistant cladding, having BOTH of the following: (a) carbon steel having an outside diameter NOT less than 355.6 mm (14 inch nominal size); (b) compliance with Det Norske Veritas Offshore Standard F101 (DNV-OS-F101) Op. 29.04.2009 Dec. 17.07.2009 - TC 0914155 7307.93.00 FITTINGS, BUTTWELD, being ANY of the following: (a) bends; (b) crosses; (c) elbows; (d) reducers; (e) tees Op. 06.06.2005 Dec. 24.10.2005 - TC 0506772 7307.93.00 FITTINGS, buttweld, forged, integrally reinforced, contoured-insert vessel or piping branch connections, bore sizes 15 mm - 1 200 mm Op. 01.03.1993 Dec. 04.06.1993 - TC 9308562 7307.93.00 REDUCERS, buttweld, having a minimum outside diameter between 70 mm and 200 mm (+ or - 0.001%) Op. 11.02.1998 Dec. 11.05.1998 - TC 9801278 7307.93.00 FITTINGS, buttweld, to specifications BS1640 OR ANSI B16.9 OR ANSI B16.28, being ANY of the following: (a) bends, 30 degrees, 45 degrees, 50 degrees, 60 degrees, 90 degrees OR 180 degrees, having an outside diameter between 17 mm and 406.4 mm; (b) tees, equal OR reducing, having an outside diameter of 406.4 mm OR less For the purposes of this order, ALL measurements have a tolerance of + OR - 5% Item 50 applies unless otherwise stated. Tariff Description =========================================================================== Op. 11.02.1998 7307.99 7307.99 Dec. 12.08.1998 - TC 9806998 ELBOWS, socketweld, being ANY of the following: (a) 15 degrees; (b) 45 degrees; (c) 90 degrees ID exceeding 50.8 mm Op. 06.03.1984 Dec. 06.03.1984 - TC 8341420 JOINTS, insulating, monobloc or monolithic Op. 28.02.1984 Dec. 28.02.1984 - TC 8341449 7307.99 PLUGS, pipe, incorporating an oil resistant synthetic rubber seal capable of sealing pipes having an ID of 49 mm or greater but NOT exceeding 356 mm at pressures of 48 MPa or less Op. 28.02.1984 Dec. 28.02.1984 - TC 8341450 7307.99 COUPLINGS, hose, having a working capacity of 206 MPa or greater Op. 30.10.1984 Dec. 30.10.1984 - TC 8434699 7307.99 COUPLINGS, pipe or hose, quick connect (or disconnect), comprising male and female ring lock couplings, hinged ring band snap lock and double lip gasket, to suit pipes and hoses having an OD of 50 mm or greater Op. 14.12.1984 Dec. 30.04.1985 - TC 8530126 7307.99 UNIONS, hammer, being four lug wing nut type with replaceable rubber seal, having ANY of the following nominal connecting pipe sizes on slipfit female pipe end and in Schedule 80 buttweld, male component weld end: Nominal connecting Nominal size pipe size (female end) pipe (weld end) Outside Dia Outside Dia (a) 114.3 mm 152.4 mm; (b) 168.28 mm 203.2 mm; (c) 219.08 mm 254.0 mm; (d) 273.05 mm 304.8 mm; (e) 323.85 mm 355.6 mm; (f) 355.6 mm 406.4 mm; (g) 406.4 mm 457.2 mm Op. 21.04.1987 Dec. 27.08.1987 - TC 8733860 7307.99 RINGS, gasket or packing, to API Specification 6A, capable of operating at temperatures of 125 degrees C or greater Op. 01.01.1988 Dec. 27.04.1988 - TC 8802330 7307.99 FITTINGS, pipe, fluoro-polymer lined Op. 12.02.1988 Dec. 21.12.1988 - TC 8802801 7307.99 FITTINGS, steel pipe, being EITHER of the following: (a) three lug wing nut unions, dia NOT exceeding 300 mm, minimum operating pressure 6.80 MPa; (b) hub clamp assemblies, consisting of ALL of the following: (i) clamp segments; (ii) hubs; (iii) seal ring Op. 23.02.1988 Dec. 16.09.1988 - TC 8802877 7307.99 COUPLINGS, casing or tubing, seamless to Specification API-5CT, section 8 Op. 05.12.1988 Dec. 07.06.1989 - TC 8902264 7307.99 JOINTS, swivel, pressure rating over 40 MPa Op. 23.04.1991 Dec. 02.09.1991 Item 50 applies unless otherwise stated. - TC 9104099 Tariff Description =========================================================================== 7307.99 CLAMPS, pipe repair (but NOT including clamps incorporating stainless steel flexible bands), having ALL of the following characteristics: (a) seal by ANY of the following methods: (i) clamping or thrust screws; (ii) girder rings; (iii) packing or force screws; (b) carbon steel construction; (c) of fixed dia; (d) capable of withstanding a working pressure of 6 900 kPa or greater Op. 01.01.1988 Dec. 11.09.1992 - TC 9206167 7307.99 CLOSURES, pressurised pipeline, hinged, quick release, diameter 150 mm or greater, but NOT including screw top type closures Op. 13.07.1992 Dec. 08.10.1992 - TC 9206615 7307.99.00 CONNECTOR HUBS, PIPE CLAMP, carbon steel, with OR without seals Op. 17.06.2014 Dec. 10.09.2014 - TC 1420344 7307.99.00 END CAPS, PRESSURE VESSEL Op. 01.08.2013 Dec. 21.10.2013 - TC 1325951 7307.99.00 CONNECTORS OR COUPLINGS, CASING OR TUBING, OIL AND/OR GAS WELL, conforming to American Petroleum Institute Specification 5CT (API 5CT) Op. 15.04.2013 Dec. 15.07.2013 - TC 1312752 7307.99.00 CROSSOVER CONNECTORS, OIL AND/OR GAS WELL EQUIPMENT, SUBSEA AND/OR SURFACE Op. 25.01.2013 Dec. 08.04.2013 - TC 1303345 7307.99.00 COUPLINGS, CROSSOVER, OIL AND/OR GAS WELL EQUIPMENT, SUBSEA AND/OR SURFACE Op. 15.01.2013 Dec. 03.04.2013 - TC 1301796 7307.99.00 COUPLINGS, PIPE, compression, hot dipped galvanised, having ALL of the following: (a) inside diameter NOT less than 30 mm; (b) single sealing sleeve consisting of a single sealing lip on each side with progressive sealing effect; (c) single radial positioned locking system with 1 OR 2 OR 3 screws Op. 26.07.2012 Dec. 22.10.2012 - TC 1227051 7307.99.00 FITTINGS, TUBE, carbon steel, with OR without seals, having an internal AND/OR external zinc coating NOT greater than 8 micron, being ANY of the following: (a) couplings having a diameter NOT greater than 200 mm; (b) reducers; (c) bends; (d) T junctions; (e) union connectors; (f) adaptors Op. 18.10.2010 Dec. 13.01.2011 - TC 1046729 7307.99.00 FITTINGS, MULTILAYERED WELDED STEEL PIPE, being ANY of the following: (a) elbows; (b) joints; (c) reducers; (d) T fittings; (e) bends; (f) end caps Item 50 applies unless otherwise stated. Tariff Description =========================================================================== 7307.99.00 7307.99.00 Op. 07.06.2010 Dec. 30.08.2010 - TC 1025390 TERMINATION HEADS, subsea Op. 05.01.2009 Dec. 27.03.2009 - TC 0946016 OILWELL CONNECTORS, having ALL of the following: (a) nonhelical interlocking teeth; (b) metal to metal seals; (c) diameter NOT less than 50.8 cm Op. 29.07.2005 Dec. 07.10.2005 - TC 0509995 7307.99.00 FITTINGS, COUPLING, HOSE, quick connect, being ANY of the following: (a) male sections; (b) female sections; (c) lever rings; (d) male plugs; (e) female caps Op. 21.12.2007 Dec. 07.03.2008 - TC 0721938 7307.99.00 COUPLINGS, HOSE, QUICK CONNECT, comprising ALL of the following; (a) male sections; (b) female sections; (c) lever ring Op. 21.12.2007 Dec. 07.03.2008 - TC 0721939 7307.99.00 FITTINGS, PIPE, being EITHER of the following: (a) hot tap; (b) line stop Op. 21.04.2008 Dec. 11.07.2008 - TC 0804852 CONNECTORS, HYDRAULIC HOSE, steel Op. 13.08.2008 Dec. 31.10.2008 - TC 0826255 7307.99.00 7307.99.00 FITTINGS, PIPE, forged, integrally reinforced, contoured-insert vessel or piping branch connections, having a bore size NOT less than 15 mm and NOT greater than 1 200 mm Op. 04.09.2008 Dec. 28.11.2008 - TC 0829428 7307.99.00 FITTINGS, ROOF DRAINAGE, galvanized steel, being ANY of the following: (a) rainwater outlets; (b) inclined outlets; (c) hoppers; (d) elbows; (e) s-curves; (f) hinged outlets; (g) pipe flaps including sets of 2 or more of the above Op. 14.10.2008 Dec. 14.01.2009 - TC 0835300 7307.99.00 FITTINGS AND ADAPTORS, PIPE OR TUBE OR HOSE, carbon steel, with or without seal, being ANY of the following: (a) reducing or enlarging bush, hexagon; (b) caps, solid or swivel; (c) crosses; (d) nipples, being ANY of the following: (i) hexagon; (ii) barrel; (iii) plain; (iv) reducing; (e) sockets, including reducing and enlarging; (f) plugs, square head or hex head or internal or external hexagon; Item 50 applies unless otherwise stated. Tariff Description =========================================================================== (g) unions; (h) tube welds or weld-on's; (i) tube compression and tube flared fittings Op. 03.12.2008 Dec. 27.02.2009 - TC 0842546 7307.99.00 FITTINGS, pipe and tube, metric, including sealing rings, bodies and nuts, to specifications DIN 2353 or DIN 3859 in ANY of the following sizes: (a) 4 mm; (b) 6 mm; (c) 8 mm; (d) 10 mm; (e) 12 mm; (f) 14 mm; (g) 15 mm; (h) 16 mm; (i) 18 mm; (j) 20 mm; (k) 22 mm; (l) 25 mm; (m) 28 mm; (n) 30 mm; (o) 35 mm; (p) 38 mm; (q) 42 mm; (r) 50 mm Op. 02.12.1993 Dec. 11.04.1994 - TC 9400309 7307.99.00 COUPLINGS, pipe or hose, quick connect (or disconnect), comprising male and female ring lock couplings, hinged ring band snap lock, to suit pipes and hoses having an OD of 50 mm or greater Op. 24.02.1994 Dec. 03.06.1994 - TC 9402433 7307.99.00 FITTINGS, pipe, high pressure, steel, complying with ALL the following standards: (a) ASTM A105; (b) ANSI B16.11; (c) BS3799 Op. 27.04.1994 Dec. 29.07.1994 - TC 9404403 7307.99.00 BRANCH CONNECTIONS, weld on type, complying with ALL the following standards: (a) ASTM A105; (b) ANSI B31-1 1980; (c) ANSI B16-9; (d) BS3351 1971 Op. 27.04.1994 Dec. 05.08.1994 - TC 9404404 7307.99.00 FITTINGS, pipe and tube, including sealing rings, bodies, nuts and weld cones, having BOTH of the following: (a) compliance with pressure rating being either LL, L or S to DIN 2353; (b) interchangeability of the whole or any component of the fitting with other fittings or components which comply with the dimensional specifications set out in DIN 2353, but NOT including ANY of the following: (a) stainless steel fittings; (b) twin ferrule fittings Op. 25.11.1994 Dec. 14.03.1995 - TC 9409468 7307.99.00 FITTINGS, STEEL, being EITHER of the following: (a) hose couplings having a female ACME coupling connection within the range of 44.45 mm to 82.55 mm (both inclusive); (b) adapters with male ACME connection within the range of Item 50 applies unless otherwise stated. Tariff Description =========================================================================== 44.45 mm to 82.55 mm (both inclusive) Op. 14.02.1995 Dec. 20.10.1995 - TC 9501971 7307.99.00 FITTINGS, PIPE, unthreaded, being ANY of the following: (a) joining rings having a diameter of 80 mm or greater but NOT exceeding 800 mm; (b) pressed bends of galvanised or mild steel in angles from 7.5 degrees or greater but NOT exceeding 90 degrees and diameter of 80 mm or greater but NOT exceeding 400 mm; (c) straight ducting with fully rolled beaded edge having a diameter of 155 mm or greater but NOT exceeding 160 mm; but NOT including fittings of stainless steel Op. 31.08.1995 Dec. 08.12.1995 - TC 9510236 7307.99.00 CLOSURES, PRESSURISED PIPELINE, having ALL of the following: (a) a cap; (b) a welding hub, with an integrated semi-dovetailed O-Ring groove in the face; (c) capable of horizontal, vertical or angle installations Op. 22.03.1996 Dec. 28.06.1996 - TC 9604891 7307.99.00 FITTINGS, TUBE, carbon steel, twin ferrule Op. 17.11.1997 Dec. 23.01.1998 - TC 9710154 7307.99.00 FITTINGS, ON-LINE HYDRAULIC LINE TESTING, being couplers, adaptors OR stand pipes, working pressures up to 40 MPa in hose sizes 2 mm and 4 mm Op. 10.12.1997 Dec. 27.02.1998 - TC 9710916 7307.99.00 GROUND CONES, FLEXIBLE METAL CONDUIT FITTING Op. 26.02.1998 Dec. 11.05.1998 - TC 9801691 NIPPLES, LANDING, SUB SURFACE FLOW CONTROL Op. 01.05.1998 Dec. 17.07.1998 - TC 9803639 7307.99.00 7307.99.00 COUPLINGS, SUCKER ROD, 12.7 mm to 28.6 mm (1/2" to 1 1/8") Op. 05.11.1998 Dec. 15.01.1999 - TC 9809843 7308.10.00 PARTS, MODULAR PANEL BRIDGING, conforming to BS:EN 10025 and BS:EN 10113, being ANY of the following: (a) panels; (b) chord reinforcement; (c) rakers; (d) frames; (e) transoms; (f) sway brace; (g) braces; (h) decks; (i) kerbs; (j) in fills; (k) post ends; (l) beams; (m) screw deck clamps; (n) signs; (o) plates; (p) plugs; (q) links; (r) extensions; (s) markers; (t) diaphragms; (u) packers; (v) spikes; (w) seal kits; (x) keys; Item 50 applies unless otherwise stated. Tariff Description =========================================================================== (y) bars; (z) tin snips; (aa) gimlets; (ab) grillages; (ac) posts; (ad) base plates; (ae) toe ramps; (af) ground beams; (ag) lugs; (ah) holdfast pickets and spikes; (ai) D shackles; (aj) slings; (ak) tirfor; (al) channels; (am) angles; (an) walkways; (ao) stanchions; (ap) handrails; (aq) staircases; (ar) blocks; (as) sway frames; (at) rollers; (au) links; (av) stool outers; (aw) struts; (ax) ties; (ay) gauges Op. 05.12.2003 Dec. 31.03.2004 - TC 0315337 7308.30.00 SLIDING DOOR SYSTEM, CAVITY, BRICK WALL, incorporating overlapping steel mesh Op. 10.06.2009 Dec. 04.09.2009 - TC 0919622 7308.30.00 GRILLS, SECURITY, metal, retractable, self locking Op. 31.05.2006 Dec. 11.08.2006 - TC 0609406 7308.40.00 STEEL COMPONENTS, being temporary shuttering AND part of a removable modular system, including prefabricated grids AND panels, being soffit bases Op. 17.02.2014 Dec. 02.07.2014 - TC 1406250 7308.40.00 COMPONENTS, SCAFFOLDING, being ANY of the following: (a) chainwire rolls; (b) ledgers; (c) tie bars; (d) toe board clips; (e) wall ties; (f) wall tie tubes Op. 13.12.2013 Dec. 10.02.2014 - TC 1405222 7308.40.00 COMPONENTS, SCAFFOLDING, complying with Australian Standard AS 1576.2, being ANY of the following: (a) double couplers; (b) double reducers; (c) swivel couplers; (d) swivel reducers; (e) putlog half; (f) putlog hooks; (g) putlog full; (h) putlog blades; (i) internal joiners; (j) gravlock beam clamps; (k) swivel beam clamps Op. 13.12.2013 Dec. 10.02.2014 - TC 1405226 Item 50 applies unless otherwise stated. Tariff Description =========================================================================== 7308.40.00 SCAFFOLDING COMPONENTS, being ANY of the following: (a) V-housings; (b) camlocks; (c) ledgers; (d) toe board clamps Op. 13.12.2013 Dec. 10.02.2014 - TC 1405223 7308.40.00 PROPS, HOT DIPPED GALVANISED AND/OR ZINC PLATED, having a rolled thread on the outer tube Op. 13.11.2007 Dec. 29.01.2008 - TC 0719361 7308.90 RAILS, elevator guide, weight less than 6 kg/m or exceeding 26 kg/m Op. 28.02.1984 Dec. 28.02.1984 - TC 8437468 7308.90 CRASH CUSHIONS, roadside hazard, energy absorbing, meeting NCHRP 230 Test tolerances Op. 18.11.1988 Dec. 19.10.1990 - TC 8810530 7308.90.00 ACCESS BOXES OR CUBES OR PRISMS, rectangle, steel, modular, including ANY of the following: (a) connector plates; (b) end panels; (c) brackets; (d) cross beams; (e) spreader; (f) steel plate supports Op. 05.09.2014 Dec. 01.12.2014 - TC 1431647 7308.90.00 GUIDE RAILS, iron AND/OR steel, cold-drawn, having a rail length less than 5.5 m, with OR without fishplates Op. 17.04.2014 Dec. 14.07.2014 - TC 1413672 7308.90.00 SUPPORT STRUCTURES, COMPRESSOR TRAIN, TECHNICAL AMMONIUM NITRATE PLANT Op. 24.03.2014 Dec. 25.06.2014 - TC 1410306 7308.90.00 SHORING, steel, modular, hydraulic adjustable, including ALL of the following: (a) braces; (b) struts; (c) beams Op. 15.10.2013 Dec. 03.03.2014 - TC 1334324 7308.90.00 FARROWING CRATES, PIGGERY, unassembled, having ALL of the following: (a) compressed fibre panelling; (b) steel crates; (c) steel fencing; (d) plastic covers Op. 20.08.2013 Dec. 18.11.2013 - TC 1328433 7308.90.00 PARTS, STRUCTURAL STEEL SECTIONS, WHARF, being EITHER of the following: (a) topside modules NOT less than 75 tonnes; (b) dolphins NOT less than 25 tonnes Op. 17.10.2013 Dec. 17.10.2013 - TC 1332986 7308.90.00 STRUCTURES, STEEL, MARINE BERTHING, being ANY of the following: (a) marine piles NOT less than 750 mm diameter; Item 50 applies unless otherwise stated. Tariff Description =========================================================================== (b) dolphins NOT less than 25 tonnes; (c) topside modules NOT less than 75 tonnes Op. 17.10.2013 Dec. 17.10.2013 7308.90.00 - TC 1332984 TEMPLATES, ANCHOR BOLT, TECHNICAL AMMONIUM NITRATE (TAN) PLANT Op. 30.05.2013 Dec. 26.08.2013 - TC 1317818 7308.90.00 SOLDIERS, FORMWORK, having ALL of the following: (a) length NOT greater than 3 650 mm; (b) width NOT less than 220 mm; (c) hole diameter NOT greater than 105 mm Op. 19.04.2013 Dec. 05.08.2013 - TC 1313426 7308.90.00 PARTS, STRUCTURAL STEEL, COAL PLANT OR IRON ORE PLANT, being ANY of the following: (a) rolled, hollow or welded sections; (b) beams; (c) grating, (d) stairways and/or treads; (e) plates; (f) handrails (with or without kick plates); (g) stanchions; (h) purlins and girts; (i) packing and shims; (j) guards; (k) legs; (l) stringer and ground modules; (m) frames; (n) wear liners; (o) gantries Op. 30.04.2013 Dec. 11.06.2013 - TC 1319269 7308.90.00 STRUCTURES, STEEL, GAS FUELLED POWER PLANT, being EITHER of the following: (a) exhaust gas stack; (b) radiator platform Op. 13.03.2013 Dec. 18.06.2013 - TC 1309205 7308.90.00 WATER DIVERSION OR DAM BARRIERS, mobile, including ALL Of the following: (a) steel A shaped frames; (b) steel connecting rods; (c) plywood AND/OR aluminium panels; (d) plastic membrane sheets; (e) steel clips AND chains; (f) storage crates AND wooden pallets Op. 19.02.2013 Dec. 02.05.2013 - TC 1306230 7308.90.00 SPACE FRAMES, SPHERICAL DISH, SOLAR CONCENTRATOR, having BOTH of the following: (a) maximum wind loading NOT greater than 147.6 kilometres per hour; (b) maximum force on base NOT greater than 170 000 kN Op. 21.12.2012 Dec. 18.03.2013 - TC 1248776 7308.90.00 ACCESS FLOORING, having BOTH of the following: (a) steel encapsulated chipboard core panels AND/OR calcium sulphate core panels; (b) pedestals, including a head, base and gasket Op. 23.10.2012 Dec. 14.01.2013 - TC 1240491 Item 50 applies unless otherwise stated. Tariff Description =========================================================================== 7308.90.00 PARTS, ACCESS FLOORING, being ANY of the following: (a) steel encapsulated chipboard core panels AND/OR calcium sulphate core panels; (b) pedestals, including a head, base and gasket; (c) stringers, complete with gasket Op. 23.10.2012 Dec. 14.01.2013 - TC 1240492 7308.90.00 STRUCTURES, STEEL, GAS STACK, VENT OR FLARE, including ALL of the following: (a) gas stack tubes; (b) bracing; (c) beams; (d) ladders; (e) handrails Op. 15.10.2012 Dec. 07.01.2013 - TC 1239299 7308.90.00 PARTS, FOUNDATION, VERTICAL ROLLER MILL, CEMENT GRINDING, being ANY of the following: (a) multi-drive foundation frames; (b) thrust bearing gearbox base plates; (c) gearbox plate recess boxes; (d) anchorage base plates; (e) mill foundation anchor plates; (f) mill foundation slide rails; (g) rocker arm support pedestals; (h) assembly and alignment equipment having ALL of the following: (i) I-beams; (ii) threaded rod; (iii) compensation plates; (iv) plates, (i) anchor bolt recess boxes; (j) I-beams being foundation embedments Op. 30.08.2012 Dec. 21.11.2012 - TC 1232381 7308.90.00 PARTS, LAMINATED SAFETY GLASS PRODUCTION LINE STRUCTURES, being ANY of the following: (a) girders; (b) trusses; (c) grating; (d) handrails (with or without kick plates); (e) gates; (f) treads; (g) crane rails; (h) frames; (i) crane portal beams Op. 27.07.2012 Dec. 22.10.2012 - TC 1227168 7308.90.00 MARINE BERTH MODULES, having ALL of the following: (a) width NOT less than 16 m; (b) length NOT less than 39 m; (c) weight NOT less than 400 t Op. 01.08.2012 Dec. 15.10.2012 - TC 1227730 7308.90.00 PARTS, MODULAR MULTIDIRECTIONAL FRAMEWORK, conforming to European Standard 13480 (EN:13480) and European Standard 1993 (EN:1993), being ANY of the following: (a) adapters; (b) bases; (c) beams; (d) ends; (e) joints; (f) plates; Item 50 applies unless otherwise stated. Tariff Description =========================================================================== (g) spider clamps Op. 26.06.2012 7308.90.00 Dec. 12.09.2012 ROOFING, MODULAR, being ANY of the following: (a) roof cassettes; (b) ridge cassettes; (c) roof beams; (d) roof girders; (e) ridge supports; (f) beam stiffeners; (g) tubular stiffeners; (h) lattice beam connectors; (i) wedges; (j) clamping plates; (k) roof supports Op. 29.12.2011 Dec. 26.03.2012 - TC 1222230 - TC 1142644 7308.90.00 PARTS, STRUCTURE, OFFSHORE OIL AND/OR GAS RIG, whether OR not assembled, being ANY of the following: (a) baffle OR box OR diaphragm plates; (b) bases OR foundations OR platforms OR platform inserts; (c) braces; (d) bulkheads; (e) frames; (f) primary OR secondary bumpers; (g) stairs OR ladders; (h) supports; (i) walls OR panels Op. 09.12.2011 Dec. 07.03.2012 - TC 1141301 7308.90.00 PARTS, MARINE WHARF, being steel pile caps Op. 16.11.2011 Dec. 30.01.2012 - TC 1138231 7308.90.00 PANELS, INSULATING, consisting of polyurethane inner core with galvanised steel sheeting BOTH sides, having BOTH of the following: (a) steel sheet thickness NOT less than 0.4 mm; (b) polyurethane thickness NOT less than 20 mm Op. 27.07.2009 Dec. 09.10.2009 - TC 0926917 7308.90.00 MARINE PILINGS, steel, having ALL of the following: (a) thickness NOT less than 20 mm; (b) length NOT less than 28.5 m; (c) diameter NOT less than 900 mm; (d) maximum of one splice per piling; (e) maximum straightness difference of 1 mm per metre over entire length Op. 30.04.2009 Dec. 24.07.2009 - TC 0914435 7308.90.00 STRUCTURES, FACADE, woven mesh, stainless steel Op. 18.04.2007 Dec. 06.07.2007 7308.90.00 - TC 0705685 PARTS, FORMWORK, PANEL WALL SYSTEM, being ANY of the following: (a) adapters; (b) add-on pieces; (c) adjustment pieces; (d) angles; (e) bases; (f) braces; (g) brackets; (h) clamps; (i) cones; (j) connector assemblies, comprising both ends and clamps; Item 50 applies unless otherwise stated. Tariff Description =========================================================================== (k) connectors; (l) hinged and/or fixed corners; (m) cross-bars; (n) ends; (o) fasteners; (p) form strips; (q) frames; (r) guardrails; (s) joints; (t) locating pins; (u) mid rails; (v) panels; (w) plates; (x) platform beams; (y) platforms; (z) plugs; (aa) posts; (ab) props; (ac) railing; (ad) spindles; (ae) spacer and/or centre tubes; (af) stiffeners; (ag) stop ends; (ah) struts; (ai) tie rods; (aj) tighteners; (ak) transport hooks; (al) triangular wedges; (am) waler spanners; (an) walers; (ao) wedges Op. 13.11.2007 Dec. 29.01.2008 7308.90.00 - TC 0719350 PARTS, FORMWORK, SOLDIER SYSTEM, being ANY of the following: (a) adapters; (b) bases; (c) braces; (d) brackets; (e) clamps; (f) clips; (g) connectors; (h) couplers; (i) edge angles; (j) fork arms; (k) fork heads; (l) guardrails; (m) jacks; (n) lifting loops and/or plates and/or brackets; (o) pivots; (p) plates; (q) plumbing braces; (r) posts; (s) shoring adapters; (t) soldiers, having holes NOT greater than 70 mm diameters; (u) spreader connections and/or beams and/or adaptors; (v) stabilisers; (w) turnbuckles; (x) u-heads; (y) brackets (high load washer); (z) web stiffeners; (aa) wheel and bracket assemblies, comprising both wheels and brackets Op. 13.11.2007 Dec. 29.01.2008 - TC 0719351 Item 50 applies unless otherwise stated. Tariff Description =========================================================================== 7308.90.00 PARTS, AQUACULTURE FACILITY, steel, being ALL of the following: (a) intermediate sections; (b) outrigger sections; (c) catamaran sections; (d) handrails; (e) light poles; (f) mooring lugs; (g) bollards; (h) net poles; (i) life ring holders; (j) pontoon holders; (k) mainbridge; (l) ladders Op. 02.04.2008 Dec. 04.07.2008 - TC 0805146 7308.90.00 STRUCTURES, WELLHEAD, OFFSHORE OIL AND GAS, comprising ALL of the following: (a) well head platform jacket structural steel sections; (b) piles having lengths NOT less than 28 m; (c) pile inserts having lengths NOT less than 18 m Op. 11.06.2008 Dec. 08.09.2008 - TC 0812032 7308.90.00 PARTS, MUSHROOM SUBSTRATE PASTEURIZATION TUNNELS OR BUILDINGS, being ANY of the following: (a) connection plates; (b) beams; (c) pillars; (d) panels; (e) profile sheets; (f) walls; (g) roofing Op. 07.11.2008 Dec. 30.01.2009 - TC 0838882 7308.90.00 SHAPES AND PROFILES, of puddled wrought iron Op. 13.01.1994 Dec. 22.04.1994 - TC 9401293 7308.90.00 CHILD SAFETY GATES OR EXTENSIONS, DOMESTIC, internal Op. 29.09.2000 Dec. 15.12.2000 - TC 0008230 7308.90.00 GUIDE RAILS, LIFT, hot rolled, bright drawn and planed Op. 22.02.2001 Dec. 04.05.2001 - TC 0101755 7308.90.00 PARTS, ACCESS FLOORING, being ANY of the following: (a) steel cementitious floor panels; (b) pedestals; (c) stringers; (d) pedestal heads Op. 28.07.2004 Dec. 11.10.2004 - TC 0407789 7308.90.00 ACCESS FLOORING, comprising ALL of the following: (a) steel cementitious floor panels; (b) pedestals; (c) stringers; (d) pedestal heads Op. 05.08.2004 Dec. 18.10.2004 7309.00.00 - TC 0408063 TOTE BINS, stainless steel, having ALL of the following: (a) capacity NOT greater than 800 litres; (b) operating pressure NOT greater than 1 bar; (c) manhole lid; (d) valves Op. 10.04.2014 Dec. 04.07.2014 - TC 1412644 Item 50 applies unless otherwise stated. Tariff Description =========================================================================== 7309.00.00 TANKS, HOT WATER, having ALL of the following: (a) welded steel plate construction; (b) insulation AND cladding thickness NOT less than 200 mm; (c) temperature capacity NOT less than 5 degrees Celsius and NOT greater than 95 degrees Celsius; (d) pressure capacity NOT less than 56 mbar; (e) water capacity NOT less than 100 000 L Op. 20.12.2013 Dec. 10.04.2014 - TC 1342075 7309.00.00 TANKS, WASTE WATER, glass lined steel, having BOTH of the following: (a) diameter NOT less than 4 200 mm; (b) height NOT less than 5 600 mm Op. 06.11.2013 Dec. 03.02.2014 - TC 1337391 7309.00.00 CONTAINMENT SYSTEM, TANK, WATER AND/OR BRINE, expandable, portable, including ALL of the following: (a) tank wall panels; (b) liner clamp; (c) wind ring; (d) maximum capacity NOT greater than 21,005 cubic metres; (e) maximum diameter NOT greater than 150 metres Op. 09.04.2013 Dec. 25.09.2013 - TC 1312233 7309.00.00 TANKS, ION EXCHANGE, with OR without platforms AND ladders Op. 17.06.2011 Dec. 12.09.2011 - TC 1119444 7309.00.00 BINS, FURNACE CHARGING SYSTEM, SUBMERGED ARC FURNACE, being EITHER of the following: (a) correction feed; (b) cold feed Op. 04.01.2011 Dec. 23.05.2011 - TC 1100247 7309.00.00 TANKS, GERMINATING AND KILNING, BARLEY MALT, steel, prefabricated, having a minimum batch load capacity NOT less than 360 tonne Op. 06.08.2007 Dec. 12.10.2007 - TC 0712554 7309.00.00 TANKS, COLD WATER, DIAPHRAGM PRESSURE, having a capacity exceeding 300 L and NOT greater than 500 L Op. 07.03.2008 Dec. 16.05.2008 - TC 0803919 7309.00.00 SURGE TANKS, VERTICAL, OIL AND GAS WELL TESTING Op. 06.08.2008 Dec. 24.10.2008 - TC 0825351 DUST AND FILLER SILO MODULE, ASPHALT PLANT Op. 05.09.2008 Dec. 12.12.2008 - TC 0829721 7309.00.00 7309.00.00 RECLAIMED ASPHALT PAVEMENT (RAP) MODULE, ASPHALT PLANT Op. 05.09.2008 Dec. 28.11.2008 - TC 0829756 7309.00.00 COLD FEED MODULE, ASPHALT PLANT Op. 05.09.2008 Dec. 28.11.2008 - TC 0829971 7310.10.00 TANKS, COLD WATER, DIAPHRAGM PRESSURE, having a capacity NOT less than 50 L and NOT greater than 300 L Op. 06.03.2008 Dec. 16.05.2008 - TC 0803685 7310.10.00 KEGS, BEVERAGE, stainless steel, with OR without spears Op. 26.06.2003 Dec. 15.09.2003 - TC 0307781 7310.29 CONTAINERS, cryogenic, insulated or vacuum wall, using liquefied gas as a refrigerant medium to store goods (OTHER THAN gas), at a temperature below - 100 degrees C Item 50 applies unless otherwise stated. Tariff Description =========================================================================== Op. 28.02.1984 Dec. 28.02.1984 - TC 8341467 7310.29.00 KEGS, BEVERAGE, stainless steel, having a volume capacity less than 50 L, with OR without keg spears Op. 14.05.2014 Dec. 04.08.2014 - TC 1416208 7310.29.00 TINS, PACKAGING, tin coated, with or without hinged lid Op. 15.09.2009 Dec. 27.11.2009 - TC 0934614 7310.29.00 TANKS, COLD WATER, diaphragm pressure, having a volume capacity NOT greater than 50 L Op. 06.07.2009 Dec. 18.09.2009 - TC 0923307 7310.29.00 TANKS, COLD WATER, diaphragm pressure, having a capacity less than 50 litres Op. 04.06.2009 Dec. 28.08.2009 - TC 0918884 7310.29.00 JERRY CANS, conforming to Australian/New Zealand Standard 2906:2001 (AS/NZS 2906:2001) Op. 28.01.2009 Dec. 19.06.2009 - TC 0902741 7310.29.00 TINS, NOVELTY, having less than 220 grams of confectionery and/or bakers wares Op. 15.09.2005 Dec. 25.11.2005 - TC 0512191 7310.29.00 TINS, DISPLAY, having BOTH of the following: (a) tin sheet thickness NOT less than 0.2 mm and NOT greater than 0.4 mm; (b) transparent display windows Op. 29.12.2006 Dec. 23.03.2007 - TC 0620288 7310.29.00 TINS, PACKAGING, printed, with or without hinged lid, capacity NOT greater than 3.5 kg Op. 26.11.2008 Dec. 27.02.2009 - TC 0841237 Item 50 applies unless otherwise stated.
© Copyright 2025