MultiChoice™ Universal Pressure Balance Tub and Shower Formerly 11T5 Series T13H163 TRIM • Scald Guard Cartridge Requires less Maintenance. • Long Life, Low Maintenance, with Machined Brass Parts. • Blue/Red Visual valve cover indicator for Cold, Hot/Cold mixing and Hot outlet water handle positions. • Safer Operation as Lever Handle ALWAYS OPENS with “COLD” water first. • Low TURNING FORCE Vandal Resistant Metal Lever Handle for Easier Operation. ADA compliant. • Maximum Temperature Control PRE-SETTING Stop is located under the Handle. Meets ASSE 1016 High Temperature Rotational Limit Stop Requirement. • Delta Monitor ® shower/bath valves are ENGINEERED to provide user PROTECTION through the following built-in SAFEGUARDS: • Monitor PRESSURE BALANCE Control. • Lever Handle ALWAYS OPENS Cold Water Flow First. • Limit Stop for PRE-SETTING Maximum Temperature. • INTEGRAL CHECKS in the Cartridge Prevent Crossflow between Hot and Cold Water Inlets. • Wider COMFORT Zone. • ADA Compliant handle meets Handicapped Accessibility Standard ASME A117.1 of less than 5 LBS. Operating Force. Refer to www.specselect.com for individual models. Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation. Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability. Page 2.C.1 MultiChoice™ Universal Pressure Balance Tub and Shower R10000-UNWS ROUGH-IN (INTEGRAL STOPS SUPPLIED STANDARD – NOT SHOWN) • Mounting Bracket – Provides a sturdy method to secure the valve to a stringer and prevents rocking. • Square Plasterguard – Standard tile size allows for simple 90° cuts. • Heavy Duty Forged Brass one piece valve body. • Heat-Resistant Pressure Test Cap – Allows for water testing up to 300 psi before the valve cartridge is installed. Easy access for flushing out the system. • Chrome Plated Bonnet Nut – Allows for easy removal during maintenance, even after years of use. • 1/2" Universel Inlets to accept 1/2" copper, 1/2" iron pipe, PEX or CPVC adaptors. • 1/2" Universel Outlets, inlets/outlets have male threads. • Integral Stops (supplied standard with R10000-UNWS and R10700-UNWS Rough-Ins – NOT SHOWN) for service and maintenance at any individual tub and shower valve allowing continued normal use of other valves in the same room or area. • Increased Flow allows faster filling of tubs. • R10700-UNWS – Rough-In for Pressure Balancing Valve with separate In-Wall Diverter Valve. Refer to www.specselect.com for individual models. Note: Use this page as a product submittal sheet. See Page 2.C.7 for additional Rough-In options. Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation. Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability. MultiChoice™ Universal Pressure Balance Tub and Shower Specification: (example) ❏ R10000-UNWS ROUGH-IN only • • • • Concealed in-wall MultiChoice™ universal valve Back-to-back capability, Integral screwdriver stops Heavy Duty forged brass valve body 1/2" Universal inlets to accept 1/2" copper, 1/2" iron pipe, PEX or CPVC adaptors • 1/2" Male thread inlets/outlets T13H163 ❏ FINISH TRIM ONLY: • Pressure Balancing cartridge with checks T13H153 • Polished chrome plated finish • 57mm (2.24'') ADA Compliant valve handle and … with … (add product variation) with … (add shower) TUB AND SHOWER DESCRIPTION ROUGH-IN Valve FINISH TRIM only Engineer/Architect Approval Model Specified: Approval: PRODUCT NO. R10000-UNWS T13H PRODUCT VARIATION 3 Date: Formerly 11T5 Series HANDLE SHOWER ✔ ✔ ✔ 0 Specify ''0'' When No Shower Outlet Required 0 1 Standard Brass Fixed Spray Showerhead Arm & Flange 2.2 USGPM (8.4 L/min.) 1 2 Dual Spray TouchClean Showerhead, Arm & Flange 2.5 USGPM (9.5 L/min.) 2 3 3 Push-Clean Showerhead Arm & Flange 2.5 USGPM (9.5 L/min.) 3 4 4 0 1 2 Shower Valve Only Tub and Shower 4 5 Handshower, VB (ASSE) 610mm (24'') Combination S/S Slide Grab Bar 2.5 USGPM (9.5 L/min.) 5 6 6 30° Vandal Resistant Cast Wallmount Showerhead 2.0 USGPM (7.6 L/min.) 6 7 7 Handshower, VB (ASSE) Wall Elbow, 2 Wall Hooks 2.5 USGPM (9.5 L/min.) 7 8 8 H2Okinetic Technology™ Showerhead, Arm & Flange, 1.6 USGPM (6.0 L/min.) 8 9 9 Adjustable, Metal Showerhead, Arm & Flange, 2.5 USGPM (9.5 L/min.) 9 5 SET SCREW SHOWER ARM FLANGE SUPPLIED ON SHOWER OPTION NO. 1, 2, 3, 8, AND 9. FLOWRATES ARE AT 80 PSI. See Page 2.C.4 for Add-On options available. Refer to www.specselect.com for individual models. See Page 2.C.7 for additional Rough-In options. 57mm (2.24'') Lever Blade Handle Note: Use this page front and back as a product submittal sheet. Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation. See current price list for product availability. Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability. Page 2.C.2 MultiChoice™ Universal Pressure Balance Tub and Shower Approvals: • CSA certified • Complies to ASME A112.18.1 • Pressure Balance Handle ADA Compliant and meet Handicapped Accessibility Standard ASME A117.1 of less than 5 lbs. operating force. • ASSE 1016 • Handshower Vacuum Breaker Certified under ANSI A1121.3 (ASSE 1011) • IAPMO listed (Contact Delta Representative for State and/or Local Approvals.) 70mm (2.75") 102mm (4.0") 152mm (6.0") 910mm (36.0") OPTIONAL FLOWRATE vs PRESSURE FLOW (l /min.) Shower Outlet Flowrates FLOW (USGPM) 3.5 13 12 3 11 10 2.5 9 8 2 7 6 51mm (2.0") 1.5 5 4 3 1 2 .5 1 0 0 10 0 20 30 40 50 60 70 80 Line Pressure (psig) Shower Outlets No. 1 (060890A) No. 6 (060793A) No. 8 (RP46384) STOPS METAL BLADE HANDLE 178mm (7.0") Ø HOT & COLD INLETS 14 0 0 No. 2 & 3 (RP28601, RP38357) No. 5 & 7 (RP7405) C L VALVE BODY No. 9 (060653A) FLOWRATE vs PRESSURE FLOW (l/min.) FLOW (USGPM) Tub Filler Flowrates FRONT VIEW SIDE VIEW 8 29.5 28 910mm (36.0") OPTIONAL 7.5 26.5 7 25 6.5 23.5 6 22 R10000-UNWS Rough-In with T13H133 Trim TO FLOOR 5.5 20.5 5 19 17.5 4.5 16 4 14.5 3.5 13 11.5 3 20 30 40 50 60 70 80 Line Pressure (psig) Refer to www.specselect.com for individual models. DSP-T13H1 Rev. A P/B VALVE INLETS: 1/2'' Universal inlets accept 1/2" copper, 1/2" iron pipe, PEX or CPVC adaptors 1/2" Male thread inlets/outlets Note: Measurements may vary ± 6mm (0.25'') Note: Use this page front and back as a product submittal sheet. Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation. Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability. MultiChoice™ Universal Pressure Balance Tub and Shower with Diverter Valve for Dual Showers Specification: (example) ❏ R10700-UNWS ROUGH-IN only • Concealed in-wall MultiChoice™ universal valve • Heavy Duty forged brass valve body, Integral screwdriver stops • 1/2" Universal inlets to accept 1/2" copper, 1/2" iron pipe, PEX or CPVC adaptors • 1/2" Male thread inlets/outlets, Back-to-back capability • In-wall diverter valve T13H923 ❏ FINISH TRIM ONLY: • Pressure Balancing cartridge with checks • Polished chrome plated finish • 57mm (2.24'') ADA Compliant valve handle • 68mm (2.68'') ADA Compliant diverter handle and … with … (add product variation) with … (add shower) TUB AND SHOWER DESCRIPTION ROUGH-IN with Diverter Valve & Stops FINISH TRIM only Engineer/Architect Approval Model Specified: Approval: PRODUCT NO. R10700-UNWS T13H PRODUCT VARIATION 3 0 1 2 Shower, Handshower, ASSE VB, Diverter Valve, 610mm (24") Combination S/S Slide/Grab Bar (1) 4 5 Shower, Handshower, Diverter Valve, VB, Wall Elbow, 2 Wall Hooks (1) 6 Tub & Shower (Same as No. 5 above) but with Diverter Spout (1) Formerly 11T5 Series HANDLE SHOWER ✔ 3 Date: ✔ ✔ 0 Specify ''0'' When No Shower Outlet Required 0 1 Standard Brass Fixed Spray Showerhead Arm & Flange 2.2 USGPM (8.4 L/min.) 1 2 Dual Spray TouchClean Showerhead, Arm & Flange 2.5 USGPM (9.5 L/min.) 2 3 Push-Clean Showerhead Arm & Flange 2.5 USGPM (9.5 L/min.) 3 4 4 5 5 6 30° Vandal Resistant Cast Wallmount Showerhead 2.0 USGPM (7.6 L/min.) 7 8 8 H2Okinetic Technology™ Showerhead, Arm & Flange, 1.6 USGPM (6.0 L/min.) 8 9 Adjustable, Metal Showerhead, Arm & Flange, 2.5 USGPM (9.5 L/min.) 9 9 7 (1) Product Variations 3 and 5 to 9 require selection of the second showerhead from Shower Option No. 1, 2, 3, 6, 8, or 9. Set screw shower arm flange supplied on Shower Option No. 1, 2, 3, 8, and 9. Refer to www.specselect.com for individual models. ✔ 6 7 Tub & Shower (Same as No. 3 above) but with Diverter Spout (1) 57mm (2.24'') Lever Blade Handle Flowrates are at 80 PSI. See Page 2.C.4 for Add-On options available. See Page 2.C.7 for additional Rough-In options. Note: Use this page front and back as a product submittal sheet. Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation. See current price list for product availability. Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability. Page 2.C.3 MultiChoice™ Universal Pressure Balance Tub and Shower with Diverter Valve for Dual Showers Approvals: • CSA certified • Complies to ASME A112.18.1 • P/B and Diverter Lever Handles ADA Compliant and meet Handicapped Accessibility Standard ASME A117.1 of less than 5 lbs. operating force. • Pressure Balance Valve ASSE 1016 • Handshower Vacuum Breaker Certified under ANSI A1121.3 (ASSE 1011) • IAPMO listed (Contact Delta Representative for State and/or Local Approvals.) I 178mm (7.0") Shower Outlet Flowrates 82-92mm (3.213"- 3.613") PLUG FOR SECOND INLET 76mm (3.0") 2 OUTLETS TO SHOWER INLET FROM MAIN VALVE FLOWRATE vs PRESSURE FLOW (l /min.) SIDE VIEW 70mm (2.75") INLET C L FLOW (USGPM) 1/2" F.I.P. INLET/OUTLET C L OUTLET 21mm (0.813") 12 3 51mm (2.0") 11 10 2.5 9 8 2 STOPS METAL BLADE HANDLE C L VALVE BODY 7 6 813mm (32.0") OPTIONAL 508mm (20.0") OPTIONAL 3.5 13 610mm (24.0") 910mm (36.0") OPTIONAL HOT & COLD INLETS 1.5 5 4 3 1 2 .5 1 0 0 0 10 20 30 40 50 60 70 80 121mm (4.75") Line Pressure (psig) Shower Outlets No. 1 (060890A) No. 6 (060793A) No. 8 (RP46384) 1/2"F.I.P. 44-66mm (1.75"-2.50") No. 2 & 3 (RP28601, RP38357) 89mm (5.25") 910mm (36.0") OPTIONAL TO FLOOR 76mm 76mm (3.0") (3.0") No. 9 (060653A) HAND SHOWER OUTLET Product Variations No. 3, 5, 6 & 9 (RP7405) 813mm (32.0") OPTIONAL FLOWRATE vs PRESSURE FLOW (l/min.) FRONT VIEW 305mm (12.0") OPTIONAL FLOW (USGPM) Tub Filler Flowrates OPTIONAL OPTIONAL 76mm (3.0") INLET WALL SHOWER OUTLET 229mm (9.0") 8 29.5 28 7.5 26.5 7 25 6.5 23.5 6 22 R10700-UNWS Rough-In with T13H923 Trim 5.5 20.5 5 19 17.5 4.5 16 4 14.5 3.5 13 11.5 3 20 30 40 50 60 70 80 Line Pressure (psig) Refer to www.specselect.com for individual models. DSP-T13H3 Rev. A 178mm (7.0") Ø P/B VALVE INLETS: 1/2'' Universal inlets accept 1/2" copper, 1/2" iron pipe, PEX or CPVC adaptors 1/2" Male thread inlets/outlets DIVERTER VALVE: 1/2'' FIP inlets/outlets Note: Measurements may vary ± 6mm (0.25'') Note: Use this page front and back as a product submittal sheet. Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation. Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability. Tub and Shower Add-On Options DESCRIPTION ADD-ON NUMBER P/B Valve Add-On Options — HOSE, ETC. MISCELLANEOUS ✔ ✔ ✔ 0 USE ''0'' For No Selection 1 Quick Disconnect For Hose (2) 1 2 1753mm (69'') Long CP Brass Double Spiral Hose (2) 2 3 Same as No. 2 Above but with Quick Disconnect (2) 3 4 0 USE ''0'' For No Selection -05 -03 Adjustable Volume Control (attaches to showerarm) 4 5 914mm (36'') Combination S/S Slide/Grab Bar (3) -10 -35 Notes: (1) A Number from each option column must be used for a complete Product Add-On (2) Base Product for the HOSE, ETC. options must be from PRODUCT VARIATION TRIM No.’s 3, 5, 6 or 9 or must include SHOWER option No. 5 or 7 (3) Base Product for combination S/S Slide/Grab Bar must be from PRODUCT VARIATION TRIM No.’s 3 or 9, or must include SHOWER option No. 5 HOW TO SELECT AND SPECIFY ADD-ON OPTIONS: Example No. 1: Base Product selected is R10700-UNWS Rough-in, and a T13H323 with 36" Combination S/S Slide/Grab Bar. 36" Combination S/S Slide/Grab Bar Add-On Suffix Number is -05 Product Number to Specify: R10700-UNWS Rough-in and T13H323-05 Trim Refer to www.specselect.com for individual models. Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation. See current price list for product availability. Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability. Note: Use this page as a product submittal sheet. Page 2.C.4 Handshower Accessories ❏ 060733A 610mm (24'') sliding handshower bar, vertical mounting pin, polished chrome plated finish, vandal resistant concealed mounting. (NOTE: Sliding bar NOT to be used as a grab bar.) ❏ 060262A As above but 1219mm (48'') long ❏ 060798A 1/2'' NPT inlet/outlet polished chrome plated brass atmospheric in-line vacuum breaker. Certified under ANSI A1121.3 (ASSE 1011). ❏ RP32550 Brass showerarm mounted diverter tee, polished chrome plated finish. ❏ RP7405 Handshower head with stop button and 2.5 USGPM (9.5 L/min.) flow control. ❏ 060304A 610mm (24'') combination stainless steel slide/grab bar, 1778 mm (70") white vinyl hose, push button handshower head, ASSE vacuum breaker, wall supply elbow & flange. ❏ 060306A As above but with 914 mm (36") stainless steel slide/grab bar. (See Shower No. 5 & 7 – Page 2.C.2 See Product Variation No. 3, 5, 6 & 9 – Page 2.C.3) FLOWRATE vs PRESSURE FLOW (USGPM) FLOW (l /min.) 3.5 13 ❏ 060827A Brass swivel handshower connector, polished chrome plated finish, with hole for vertical mounting pin, 1/2'' NPS inlet/outlet). 12 3 11 10 2.5 9 8 2 7 RP7405 ❏ RP7406 As above but plastic and chrome plated brass. 6 4 3 1 ❏ 060828A Brass showerarm mount with pin, polished chrome plated finish. 2 .5 1.5 5 1 0 0 0 10 20 30 40 50 60 70 80 Line Pressure (psig) ❏ RP12504 Brass wallmounted bracket, vertical mounting pin, polished chrome plated finish. ❏ 060303A Brass wallmounted elbow, flange, polished chrome plated finish,1/2'' NPT inlet & outlet. ❏ 060312A 1778mm (70'') long white vinyl handshower hose, nylon reinforced. ❏ 060731A 1753mm (69'') long chrome plated brass double spiral handshower hose. ❏ 060252A Quick disconnect connectors for handshower hose. Note: Measurements may vary ± 6mm (0.25'') Refer to www.specselect.com for individual models. DSP-SHWA Rev. A Note: Use this page as a product submittal sheet. Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation. Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability. Shower Accessories Specification: (example) Cast brass institutional wallmounted shower head, polished chrome plated finish, 2.0 USGPM (7.6 L/min.) flow control fixed spray, concealed cast brass mounting plate, vandal resistant front mounting screws, universal 1/2'' FIP/copper sweat inlet. ❏ 060793A 30° spray angle from wall. (See Shower No. 6 – Page 2.C.2 and 2.C.3) ❏ 060852A Brass body diverter valve, ADA compliant lever handle, polished chrome plated metal trim. (See Product Variations No.’s 3, 5, 6 & 9 – Page 2.C.3) Specification: (example) 76 mm (3") Diameter wall thermometer, 18 to 82 degrees C (0 to 180 degrees F), stainless steel construction with shatterproof Lexan lens, complete with cast brass tee, polished chrome plated brass nipple and set screw wall flange. ❏ 060274A ❏ 060890A Brass body showerhead fixed 2.2 USGPM (8.4 L/min.) flow control spray, polished chrome plate finished. (See Shower No. 1 – Page 2.C.2 and 2.C.3) Specification: (example) In-wall, volume control stop, TUF-TECK institutional structure, polished chrome plated finish exposed metal trim, color indexed metal handle with vandal resistant screw, 1/2'' FIP inlet/outlet. ❏ RP28601 Dual Spray Touch-Clean®, chrome plated finish, brass ball showerhead, 2.5 USGPM (9.5 L/min.). (See Shower No. 2 – Page 2.C.2 and 2.C.3) ❏ 54T1200 With 70mm (2-3/4") ADA compliant lever blade handle and integral stop. ❏ RP38357 Touch-Clean™, polished chrome plated finish, brass ball showerhead, 2.5 USGPM (9.5 L/min.). (See Shower No. 3 – Page 2.C.2 and 2.C.3) ❏ 060732A Brass body volume control, polished chrome plated finish, flow adjustment lever handle, 1/2'' NPS inlet/outlet. ❏ 060653A Adjustable, metal showerhead, 2.5 USGPM (9.5 L/min.). 3 spray modes: full, massage, and combination spray. (See Shower No. 9 – Page 2.C.2 and 2.C.3) ❏ 060605A Forged brass Toe Tester Spout, polished chrome plated finish, 1/2'' FIP inlet. ❏ 060710A Brass bent showerarm, metal set screw wall flange, polished chrome plated finish. (Supplied with Shower No. 1, 2, 3, 8, & 9) Refer to www.specselect.com for individual models. ❏ RP46384 H2Okinetic Technology™ Showerhead, 1.6 USGPM (6.0 L/min.). (See Shower No. 8 – Page 2.C.2 and 2.C.3) Flowrates are at 80 PSI. Note: Use this page front and back as a product submittal sheet. Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation. Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability. Page 2.C.5 Shower Accessories 060793A SHOWERHEAD ANCHOR PLATE 102mm (4”) 73mm (2.88”) 73mm (2.88”) 44mm (1.75”) 46mm (1.81”) Internal Cup for 1/2” Copper Connection Finished Wall 76mm (3.0”) Wrench Lugs (3) - 7mm (.28”) Holes for Lag Screws Boss with female 1/2” I.P. Thread 54T1200 CONTROL VALVE 30° 060852A DIVERTER VALVE 44-66mm (1.75”-2.5”) 35mm DIA. (1.38”) Hole 1/2” F.I.P. 68mm (2.68”) 1/2” F.I.P. INLET / OUTLET 48mm (1.88”) 70mm (2.75”) OUTLET 21mm (.81”) INLET 61-71mm (2.4”-2.8”) 28mm DIA. (1.13”) Hole 1/2” F.I.P. 060274A WALL THERMOMETER 060605A TOE TESTER SPOUT 1/2" Copper sweat Both ends 55mm DIA. (2.15") 41 to 76mm (1.63” to 3.0”) 1/2" F.I.P. 48mm (1.90") Note: Measurements may vary ± 6mm (0.25'') Refer to www.specselect.com for individual models. DSP-SHWB Rev. A Note: Use this page front and back as a product submittal sheet. Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation. Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability. Handshower Packages ❏ 060123A SHUT-OFF BUTTON CP BRASS & PLASTIC SWIVEL ELBOW ITEM # 1 2 3 4 ❏ DESCRIPTION Handshower with Shut-off Button 2.5 U.S.GPM (9.5 L/min.) Flow Control 1778mm (70'') Long White Vinyl Handshower Hose with Nylon Reinforcement CP Brass Wallmount Bracket w/Vertical Mounting Pin and Screws CP Brass & Plastic Swivel Handshower Elbow for Vertical Mounting Pin 060124A SHUT-OFF BUTTON CP BRASS & PLASTIC SWIVEL ELBOW NOTE: SLIDING BAR NOT TO BE USED AS GRAB BAR. ITEM # 1 2 3 4 DESCRIPTION Handshower with Shut-off Button 2.5 U.S.GPM (9.5 L/min.) Flow Control 1778mm (70'') Long White Vinyl Handshower Hose with Nylon Reinforcement 610mm (24'') CP Sliding Handshower Bar w/Vertical Mounting Pin and Screws CP Brass & Plastic Swivel Handshower Elbow for Vertical Mounting Pin Note: Measurements may vary ± 6mm (0.25'') Refer to www.specselect.com for individual models. Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation. Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability. Note: Use this page as a product submittal sheet. Page 2.C.6 Handshower Packages 060127A ❏ FLOWRATE vs PRESSURE FLOW (l /min.) Handshower Package Flowrates FLOW (USGPM) 3.5 13 12 3 11 10 SHUT-OFF BUTTON CP BRASS & PLASTIC SWIVEL ELBOW 2.5 9 8 *SUGGESTED CHECK HEIGHT AGAINST LOCAL BUILDING CODES. 2 7 6 1.5 5 4 3 1 2 .5 1 0 NOTE: SLIDING BAR NOT TO BE USED AS GRAB BAR. 0 0 1/2" FNPT/COPPER (NOT SUPPLIED) ASSE APPROVED VACUUM BREAKER 44mm-76mm (1.75"-3.0") 51mm (2.0") 64mm ±10mm (2.5" ±.385") *2210mm (87") ITEM # 89mm (3.5") 1 2 3 4 5 10 20 30 40 50 60 70 80 Line Pressure (psig) Handshower Packages 060123A, 060124A,060127A, 060132A DESCRIPTION Handshower with Shut-off Button 2.5 U.S.GPM (9.5 L/min.) Flow Control 1778mm (70'') Long White Vinyl Handshower Hose with Nylon Reinforcement 610mm (24'') CP Sliding Handshower Bar w/Vertical Mounting Pin and Screws CP Brass & Plastic Swivel Handshower Elbow for Vertical Mounting Pin Wall Mounted ASSE Approved Vacuum Breaker 060132A ❏ SHUT-OFF BUTTON CP BRASS & PLASTIC SWIVEL ELBOW ITEM # ASSE APPROVED VACUUM BREAKER 1 2 3 4 5 6 DESCRIPTION Handshower with Shut-off Button 2.5 U.S.GPM (9.5 L/min.) Flow Control 1778mm (70'') Long White Vinyl Handshower Hose with Nylon Reinforcement CP Brass Wallmount Bracket w/Vertical Mounting Pin and Screws CP Brass & Plastic Swivel Handshower Elbow for Vertical Mounting Pin CP Brass Wallmount Elbow and Flange CP Brass ASSE Approved Vacuum Breaker Note: Measurements may vary ± 6mm (0.25'') Refer to www.specselect.com for individual models. DSP-SHWC Note: Use this page as a product submittal sheet. Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation. Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability. Multichoice™ Universal Rough Valve Body HDF® ■ R10000-UN (Case Qty 12) ■ R10000-UNBX (Case Qty 3) ■ R10000-UNBXT (Case Qty 3) ■ R10000-UNWS (Case Qty 12) ■ R10000-PX (Case Qty 12) ■ R10000-PXWS (Case Qty 12) ■ R10000-IP (Case Qty 12) ■ R10000-IPWS (Case Qty 12) R10000-UN R10000-UNBX R10000-UNBXT R10000-PX R10000-IP R10000-UNWS R10000-PXWS R10000-IPWS Submitted Model No.:__________________________________________________ Specific Features: _____________________________________________________ R10000-UN R10000-UNBX R10000-UNBXT 2 1/8" (54 mm) 4" (102 mm) without valve using supplied test cap. • Square plasterguard allows for right angle cuts. • Thin wall mounting. • For use with MultiChoice™ Universal single or dual 2 3/4" (70 mm) 4" (102 mm) STANDARD SPECIFICATIONS: • Forged brass body. • Back-to-Back installation capabilities. • Can be tested with air (200 PSI) or water (300 PSI) function trim. Cartridge ships with trim. 3 3/8" (86 mm) Finished Wall Stringer R10000-UNWS UP C ® 5 1/16" (135 mm) 2 1/8" (54 mm) COMPLIES WITH: • ASME A112.18.1 / CSA B125.1 2 3/4" (70 mm) 3 3/8" (86 mm) 4" (102 mm) 4" (102 mm) Finished Wall Stringer Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation. Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability. DSP-B-R10000-HDF Rev. D Page 2.C.7 Tub and Shower Faucet Trim HDF® ■ Valve Only (T13090) ■ Shower Only (T13290) ■ Tub/Shower (T13490) STANDARD SPECIFICATIONS: T13090 T13290 T13490 Submitted Model No.: _______________________________________________ Specific Features: __________________________________________________ 7" (178 mm) 8" (203 mm) min. 18" (457 mm) max. • Monitor® 13 Series pressure balanced bath mixing valve with Scald-Guard®. • Maintains a balanced pressure of hot and cold water even when a valve is turned on or off elsewhere in the system. • For use with MultiChoice™ Universal rough valve body. (R10000 Series) • Back-to-back installation capability. • Temperature only controlled with vandal resistant blade handle. • Field adjustable to limit handle rotation into hot water zone. • 120° maximum handle rotation. • All parts replaceable from the front of the valve. • Push Clean™ Showerhead/1 Spray Pattern (T13290, T13490) • Metal Tub Filler with Pull-up Diverter (T13490) Supply Face of plasterguard should be flush with finish wall line UP C ® 2-3/4" (70 mm) COMPLIES WITH: • ASME A112.18.1 • CSA B125 • Indicates ADA compliance to ICC/ANSI A117.1 ASSE 1016 Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation. Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability. Page 2.C.8 DSP-T13090 Tub and Shower Faucet Trim HDF® ■ Valve Only (T13091) ■ Shower Only (T13291) ■ Tub/Shower (T13491) STANDARD SPECIFICATIONS: T13091 T13291 T13491 Submitted Model No.: _______________________________________________ Specific Features: __________________________________________________ 7" (178 mm) 8" (203 mm) min. 18" (457 mm) max. • Monitor® 13 Series pressure balanced bath mixing valve with Scald-Guard®. • Maintains a balanced pressure of hot and cold water even when a valve is turned on or off elsewhere in the system. • For use with MultiChoice™ Universal rough valve body. (R10000 Series) • Back-to-back installation capability. • Temperature only controlled with metal lever handle. • Field adjustable to limit handle rotation into hot water zone. • 120° maximum handle rotation. • All parts replaceable from the front of the valve. • Push Clean™ Showerhead/1 Spray Pattern (T13291, T13491) • Metal Tub Filler with Pull-up Diverter (T13491) Supply Face of plasterguard should be flush with finish wall line UP C ® 2-3/4" (70 mm) COMPLIES WITH: • ASME A112.18.1 • CSA B125 • Indicates ADA compliance to ICC/ANSI A117.1 ASSE 1016 Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation. Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability. DSP-T13091 Page 2.C.9 Handshowers HDF® ■ 24" (610 mm) Slide/Grab Bar (RPW124HDF, RPW324HDF) ■ 36" (914 mm) Slide/Grab Bars (RPW136HDF, RPW336HDF) ■ Atmospheric Vacuum Breaker (RPW324HDF, RPW336HDF) ■ 90° Wall Supply Elbow (RPW324HDF, RPW336HDF) RPW124HDF RPW136HDF RPW324HDF RPW336HDF Submitted Model No.: _______________________________________________ Specific Features: __________________________________________________ Shut Off on Sprayhead is Not Positive 24" (610 mm) or 36" (914 mm) Available 3" (77 mm) Dia. STANDARD SPECIFICATIONS: • Personal white ABS hand held shower with fixed spray with push button on-off control, not a positive shut-off. • 69" (1753 mm) double spiral metal hose. • 24" (610 mm) and 36" (914 mm) stainless steel finish slide/grab bars. • ADA compliant adjustable slide mechanism. • Chrome plated atmospheric vacuum breaker, 1/2" IPS female inlet, 1/2"-14 NPSM male threaded outlet for exposed applications only. (Models RPW324HDF and RPW336HDF only). • 90° chrome plated wall supply elbow, 1/2" IPS female inlet; 1/2"-14 NPSM male threaded outlet. (Models RPW324HDF and RPW336HDF only). • 2.5 gpm @ 80 psi (9.5 L/min @ 552 kPa) from sprayhead. 69" (1753 mm) Double Spiral Metal Hose RPW124HDF RPW136HDF Accepts 1/2"-14 NPSM (male) Shut Off on Sprayhead is Not Positive 6 0 69 138 Pressure (kPa) 207 276 345 414 483 552 3" (77 mm) Dia. Accepts 1/2"-14 NPSM (male) 621 22.7 18.9 5 69" (1753 mm) Double Spiral Metal Hose RPW324HDF RPW336HDF Indicates ADA compliance to ICC/ANSI A117.1 15.1 4 11.4 3 7.6 2 3.8 1 0 Flow (Liters Per Minute) Vacuum Breaker 24" (610 mm) or 36" (914 mm) Available COMPLIES WITH: Flow (U.S. Gallons Per Minute) Wall Supply Elbow - 90° 0 10 20 30 40 50 60 Pressure (PSI) 70 80 90 0 Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation. Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability. Page 2.C.10 DSP-RPW-124-HDF Rev. D
© Copyright 2024