1. No category

POCKET-SIZED LED TESTER
Checks functionality, color, brightness and uniformity of leaded LEDs.
Test current ratings from 2-50ma.
Socket strip has seven middle
positions set at 10 mA allowing
comparison of LEDs in those spaces.
Requires 9 v battery (not included).
CAT# LT-100
$8.95 each
3 WATT LEDS ON HEATSINK
Ultra-bright high-power LEDs.
Long-life. Low-voltage. Low current.
Mounted on 20mm diameter,
star-type aluminum disc which
serves as a heatsink and provides
solder spots to simplify connection.
Note: Sensitive to misuse. We cannot guarantee
these LEDs after voltage has been applied.
COOL WHITE
18000-20000K. 3.2-3.4V, 700mA.
CAT# LED-248
$3.00 each
WARM WHITE
3500-4200K. 3.2-3.4V, 700mA.
CAT# LED-249
$3.00 each
AMBER 600-610nm. 1.9-2.3V, 700mA.
CAT# LED-253
$3.00 each
BLUE 460-470nm. 3.2-3.4V, 700mA.
CAT# LED-261
$4.00 each
ULTRAVIOLET - 410-420nM. 3.2-3.4V, 700mA.
CAT# LED-247
$6.50 each
DRIVER FOR 3W LEDS
The LEDs above can be
operated on 12 Volts
using this 3 watt driver.
Operate on 12 Vac or 12 Vdc.
CAT# LD-3
$3.25 each
5 WATT LEDS ON HEATSINK
Ultra-bright high-power LEDs.
Long-life. Low-voltage. Low current.
Mounted on 20mm diameter,
star-type aluminum disc which
serves as a heatsink and provides
solder spots to simplify connection.
12 VDC LED LIGHT STRIPS
Rugged,
highluminosity
3-LED
module suitable for indoor or outdoor, shelf, display
or sign lighting. Operates on 12Vdc. Dimmable.
Covered lens protects against humidity and sun
damage. 3M® double-stick tape for attachment to
clean, flat surface. Also has a hole for screw mounting. Modules are linked on 2-conductor 18AWG zip
cord, 161mm (6.5") center-to-center spacing. 3.75"
wire between each module. Maximum string is 50
modules, 10 Meters (32Ft). Specifications: 12Vdc,
0.72W each module. String of 50 modules = 12Vdc,
36W, 3A.
Warm White
Cool White
Yellow
Green
Blue
CAT# LS-123WW
CAT# LS-123CW
CAT# LS-123Y
CAT# LS-123G
CAT# LS-123B
$3.25 module • 10 for $3.00 per module
50 for $2.80 per module
ECONOMY 3-LED MODULES
Very bright, but not
as bright as our
LS-123CW modules.
Each weatherresistant epoxy
sealed module is
0.55" wide with
mounting holes at
each end on 3.3" centers. 3.5" wire leads connect
the modules. String of 20 modules.
Power: 12 Vdc, 0.72W per module
Viewing Angle: 140-150°
Luminous Flux: 18-20lm
New
CAT# LS-200CW - Cool-White
CAT# LS-200WW - Warm-white
$1.40 per module
20 modules for $1.10 per module
100 modules for 85¢ per module
FLEXIBLE LED STRIPS
BLUE 450-455nm. 7-7.5 Vdc 700 ma.
CAT# LED-5BL
$5.50 each
10 for $5.20 each
COOL WHITE 7000-8000 K.
7-7.5 Vdc 700 ma. CAT# LED-5CW
$5.50 each • 10 for $5.20 each
WARM WHITE 3000-4000 K .
7-7.5 Vdc 700 ma. CAT# LED-5WW
$5.50 each • 10 for $5.20 each
LENSES FOR 1W, 3W & 5W LEDS
20mm lens in a 23mm plastic holder. Works well
with our 1W, 3W & 5W LEDs, with & without star pc
board ie. LED-248, LED-249, LED-241, LED-5BL.
60° viewing angle CAT# LNS-57
$1.50 each • 10 for $1.35 each
45° viewing angle CAT# LNS-58
$1.50 each • 10 for $1.35 each
6
Flexible 8mm wide, adhesive backed ribbon with surface-mount, ultrabright white LEDs every 15mm. Ideal
for accent lighting in auto or home. Also great for
under cabinet or shelf lighting. Dimmable. Use CAT#
DMR-8. Can be cut every third LED or 50mm (approx.
2”) and each segment can be lit independently. 12Vdc
25mA per segment. Wires can be soldered directly to
ribbon tape. Sold as a continuous ribbon, up to 5 Meters (100 segments). Priced per 3-led, 50mm segments. Available in Cool, Neutral and Warm-white.
CAT# LS-12-CW
Cool-White - like fluorescent light
CAT# LS-12-NW
Neutral-white - Between Cool and Warm
CAT# LS-12-WW
Warm-white - Yellower, like incandescent light
$1.50 per 3-led segment
10 segments for $1.30 per segment
100 segments for $1.00 per segment
VISIT OUR WEBSITE - WWW.ALLELECTRONICS.COM
RED/GREEN/BLUE 12VDC LED STRIP
Each surface mount LED is capable of red, green or
blue, or any combination of colors. When all three
colors are activated LED appears white. Flexible
10mm wide strip with 3M® adhesive backing. Operates on 12Vdc. The strip can be cut every 3 LEDs,
50mm (3"). Each of these 3-LED segments has
clearly marked solder spots at both ends for attachment of wires or ribbon connectors. Strips can be
connected end to end for longer lengths. Also available is a RF controller, CAT# CT-21, which can be
used to flash the LEDs in several programmed sequences at controllable speeds, also allowing dimming. Color-coded pigtail leads at both ends for
easy connection. Sold in 3” (50mm) segments.
A full strip is 100 segments with color-coded pigtail
leads at both ends.
CAT# LS-22 $1.25 per 3-led segment
10 segments for $1.00 per segment
100 segments for 75¢ per segment
CONTROLLERS FOR
RGB LED STRIPS
Allows flashing, sequencing and dimming of tri-color
LED strip, CAT# LS-22.
RF REMOTE
Will operate up to five
strips, 1500 LEDs.
Operates on 12-24Vdc.
Input via screw terminals or 2.5mm coax
power plug. Power supply not included.
CAT# CT-21
$35.00 each
IR REMOTE
10 Amp per channel
output will operate up
to three strips. 360W
total output power.
Convenient screw
terminal strip for input and output
connections. Infrared remote control
New
provides options to make strip light in
practically any color, fade in and out of
colors, change colors at different rates and flash.
Infrared receiver "eye" on 6" lead. Remote must
operate in "line of sight" of receiver eye. Operates
on 5-24Vdc. Power supply not included.
CAT# CT-33
$17.50 each
12-24 VDC 8A DIMMER
Designed for 12-24 VDC LED strip
lights like our CAT#s LS-12-CW, NW,
WW. Clearly-marked screw-clamp
input/output terminals. Rotary
adjustment. 3.5" x 2.35" x 2.25" high
(including knob). Mounting holes on
1.6" x 3.1" centers.
CAT# DMR-8
$19.95 each
LED DISPLAYS
RED 0.8" 7-SEGMENT DISPLAY
HP # HDSP-3401. Red, common-anode
7-segment LED display, right hand
decimal. 20mm (0.8") high character.
Grey background.
CAT# SDA-26
60¢ each
RED 0.56" 7-SEGMENT LED DISPLAY
HP # HDSP-5303. Red, commoncathode 7-segment LED display, right
hand decimal. 14.2mm (0.56") high
character. Grey background.
CAT# SDC-9
50¢ each
7 SEGMENT DISPLAY
Common Anode. Fits 24 pin DIP
socket. Green. 2-digit 0.4” character
height. Prepped with two plastic
spacers which raise it 9mm from the
PC board. CAT# TDA-482
75¢ each • 10 for 65¢ each • 100 for 50¢ each
3-DIGIT LED DISPLAY, 0.56"
Ledtech# LC5673-11 EWRN.
Three 7-segment LED digits
with decimal points. 0.56"
(14.22mm) high characters.
Common cathode. Red digits on grey background.
28-pin DIP package, 37.7 x 19.0mm overall.
CAT# SDC-563 90¢ each
10 for 80¢ each • 100 for 75¢ each
4-DIGIT LED DISPLAY, 0.56"
Ledtech#LN5674-11-M1-EWRS
Four 7-segment LED digits
with decimal points, 0.56"
(14.22mm) high. Common
anode. Red digits on grey background. 50.4 x 19.05mm overall. 12-pin DIP
package. 15.24mm (0.6") spacing between rows.
CAT# SDA-25
$1.25 ea. • 10 for $1.10 ea.
ALPHA-NUMERIC LED DISPLAY
Ledtech # LA3921-11B. 0.4" high character.
14-segment with decimal point. Green LEDs
on grey background. Common anode.
Fits 18-pin DIP socket. 0.93" x 0.39".
CAT# SDA-24
50¢ each • 10 for 45¢ each
10-LED BARGRAPH
Ledtronics
#LB2512-10R3 QG.
10 red rectangular LEDs in
a white surround. 635nm.
120° viewing angle. Overall
size, 65 x 6 x 11mm high. Leads on 0.1" centers.
CAT# BG-10R3
50¢ each • 10 for 45¢ each
BARGRAPH DISPLAYS
20 pin DIP socket. 10 segments.
Color
CAT #
1-9
Red
Green
BG-10
BG-10G
1.50
1.50
10-99
1.25
1.25
100+
1.00
1.00
2.3” 5 X 8 RED-GREEN DOT MATRIX
Lite-On # LTP2558AA-RA
Large, 2.3” matrix height.
Red-Orange and Green LEDs.
Overall dimensions, 2.40” x
1.5” x 0.33”. Gray face w/
white dots in off-state. Spec sheet available.
CAT# SDD-25
$1.00 each • 10 for 80¢ each
5 X 7 DOT MATRIX LED DISPLAY, 0.68"
Ledtech #LJ7071-22. Red dots on
grey background. 12-pin DIP
package. 0.3" (7.62mm)
spacing between rows.
CAT# SDD-68 2 for $1.00
100 for 40¢ each
VISIT OUR WEBSITE - WWW.ALLELECTRONICS.COM
7
INDICATOR LAMPS
12VDC LED INDICATOR ASSEMBLIES
No external resistor required. 5mm dia.
diffused LED mounted in a 10mm dia.
chrome bezel. 8mm dia. threaded
bushing with mounting hardware.
Assembly extends 30mm below mounting panel.
Available in Red (R), Green (G), and Yellow (Y).
CAT# IND-16X (X=R,G,Y)
$ 2.25 each
LED INDICATOR ASSEMBLIES
5mm dia. diffused LED mounted in a 10mm dia.
chrome bezel. 8mm dia. threaded bushing with
mounting hardware. Operate on any DC voltage
as long as an appropriate resistor is connected.
See our LED Hook-up guide in Spec Sheets.
Available in Red (R), Green (G), Amber (A) & Blue (B).
CAT# IND-13X (X=R,G,A,B)
$ 1.75 each
12 VDC LED INDICATORS
Threaded bushings with nuts for easy mounting.
8mm above panel height. 22mm below panel
depth.Two sizes, four colors (red, green, blue,
yellow). Solder-lug terminals.
10mm dia. lens. 10mm bushing.
CAT # IND-10(R, G, B, Y)
$1.25 each • 10 for $ 1.10 each
12mm dia. lens. 12mm bushing.
CAT# IND-12(R, G, B, Y)
$1.35 each • 10 for $ 1.15 each
120V INDICATOR LAMPS
Snap-fit in 9mm dia. hole.
10mm dia.lens. 30mm long.
6" leads. Three colors (red, green, amber)
CAT# IND-120(R, G, A) $1.50 each
28V RECTANGULAR
LAMP ASSEMBLY
CHROME BASE
CAT# CLD-4X (X = B, C, R OR A)
$6.00 each • 10 for $5.50 each
BLACK BASE
CAT# BLD-4X (X = C OR B – white or blue only)
$6.00 each • 10 for $5.50 each
INCANDESCENT LAMPS
6V INCANDESCENT LAMP
WITH BLUE FILTER
6 Volt, 75mA miniature lamp assembly
with removable blue silicon-rubber
filter. 3mm diameter lamp is built-into
a 4 x 7 x 3mm high plastic platform
with wire leads on 5mm centers.
Overall height of lamp and platform is
7mm. Leads are 18mm long.
CAT# LP-71 5 for $1.00
100 for 15¢ each • 500 for 13¢ each
1000 for 10¢ each • 1500 for 9¢ each
T-1 (3MM) w/ BARE WIRE LEADS
CAT#
SoLiCo. 28V 1W. 6" pigtail leads. UL.
CAT# LP-228
4 LED CLUSTERS
5-12Vdc LED assembly designed
for use in cars or computers.
Bright, eye-catching accent-lighting.
Four-led cluster mounted in a plastic
assembly, 1.58" x 0.82" x 0.5" high.
Two recessed mounting holes on
1.15" centers. 36" cable with red and
black leads. For 12Vdc use, but they
are very bright at 5-6 Vdc.
Two colors of base available, chrome and black.
LEDs available in blue (B), red (R), white (C) and
amber (A). No mixing for discounts.
75¢ each
125VAC NEON INDICATOR ASSEMBLY
McGill red 125Vac neon indicator
assembly. 31.5 x 17mm black bezel
with 21 x 10.5mm red lens. Snapmounts in 13 x 26mm chassis hole.
34mm behind panel depth including
terminals. 0.25” qc / solder terminals.
UL, CSA. CAT# IND-34 2 for $1.00
5 Volt 115 ma
LP-715
100+
2/$1.00 $40.00
SPECIAL!
14 Volt 40 ma LP-23 3/$1.00 100/$20.00
500 for 18¢ each • 1000 for 14¢ each
T-1 3/4 (5MM) w/ BARE WIRE LEADS
CAT#
28 V 60 ma
28 Volt 65 ma
LP-28
LP-286
100+
4/$1.00 $17.00
4/$1.00 $17.00
100 for 40¢ each • 1000 for 30¢ each
T-1 (3MM) w/ INSULATED WIRE LEADS
12V GREEN INDICATOR
LAMP ASSEMBLY
1.5v @ 40 ma. 10” leads.
12 Volt incandescent indicator assembly.
7mm diameter threaded body. 8mm diameter green
jewel is 6mm in height. Solder-lug terminals.
1.5Vdc @ 75mA. 30" leads.
CAT# IND-17G
CAT# LP-3 95¢ each • 100 for 65¢ each
$1.00 each
12 LED AMBER LAMP, USED
26mm dia. x 40mm long plastic lamp
containing 12 bright amber LEDs.
No official specs. Optimal voltage
and current appears to be 11.5Vdc @
25mA. Rear of lamp has a tapped brass
insert for mounting and a rubber O-ring.
Two 18" leads with 2-pin connector. These
lamps are very sensitive to over-voltage. Like
most LEDs they will last a long time when run at
the proper voltage. However, they will burn out quickly
above 11.5Vdc. Because of the sensitivity of this part,
we cannot guarantee it. Removed from used equipment.
CAT# LED-155
8
$2.00 each
SPECIAL !
CAT# LP-41 2 for $1.00
100 for 45¢ each • 1000 for 30¢ each
3v @ 55 ma. 10” leads.
CAT# LP-4 95¢ each • 100 for 65¢ each
14v @ 45 ma. 10” leads.
CAT# LP-6 95¢ each • 100 for 65¢ each
GLASS WEDGE BASE LAMPS
T3-1/4 size. 0.40" diameter x 0.98" long.
10 pc minimum of one type (no mixing)
6.3V, 0.25A
14V, 0.27A
28V, 0.08A
CAT#
LP-259
LP-194
LP-657
ORDER TOLL FREE 1-800-826-5432
10
$3.50
$3.50
$1.50
100
$25.00
$25.00
$10.00
SPECIAL !
CYLINDER W/ HOLE
12.1mm dia. x 9.5mm, 6.4mm hole.
CAT# MAG-116 $3.00 each
LIQUID CRYSTAL
DISPLAYS (LCDs)
DISC W/ HOLE 15mm diameter x
3mm, 4mm hole. CAT# MAG-134
$1.00 each • 100 for 85¢ each
RING 19mm o.d. x 12mm i.d. x 3mm thick
CAT# MAG-133 $1.55 each
100 for $1.40 each
8 CHARACTER X 2 LINE LCD
Crystalfontz# CFAH0802A-NYG-JT. STN Positive,
Yellow/Green, Reflective. Module size: 58 x 32.0 x
8.9mm CAT# LCD-8002 $3.25 each
10 for $3.00 each
W/ HOLE FOR COUNTERSUNK SCREW
20mm diameter x 4mm thick.
5mm hole beveled to 10mm for counter
sunk #8 screw.
12 CHARACTER X 2 LINE LCD
CAT# MAG-149 $1.85 each
100 for $1.50 each
16 X 1 W/ LED BACKLIGHT
DISC 25.4mm dia. x 3.2mm thick
CAT# LCD-161 $4.50 each
10 for $4.20 each
CAT# MAG-115
$2.50 each
Ceramic magnet sandwiched
between two metal plates.
0.95" x 0.62" x 0.27" overall.
Striker plate is 2” x 0.5” x 0.1” thick.
Metal parts may have some
discoloration. No screws included.
3 for $1.00
CERAMIC MAGNETS
0.5" DIA. X 0.15"
CAT# MAG-122 10 for 80¢
96 for 6¢ each • 960 for 5¢ each
0.5” DIAMETER X 0.2”
0.1” hole in the center.
CAT # MAG-68 10 for $1.00
100 for $7.50
0.72" DIA. X 0.16" CAT# MAG-121
10 for 90¢ • 100 for $6.50
500 for 6¢ each • 1000 for 5¢ each
ALARM SWITCH MAGNET
New, unused magnet for Amseco
#AMS-17 alarm switches. Plastic
encased, Alnico-5 magnet designed to
be press-fit into 3/8” dia. hole. Brown.
CAT# MAG-170B
35¢ each • 10 for $2.50
ALNICO HORSESHOE MAGNETS
Ideal for school experiments. Includes a keeper to
help retain magnetic power.
0.98" long x 1.10" wide x
0.33" thick.
CAT# MAG-150
$2.70 each
2.00" long x 1.26" wide x
0.26" thick.
CAT# MAG-151
$4.55 each
CAT# LCD-220
$4.00 each
Picvue Electronics Ltd.# PVC160101BYL04.
STN yellow. Module size: 80.0 x 36.0 x 13.5mm.
16 X 2 W/ LED BACKLIGHT
CABINET LATCH MAGNET
CAT# MAG-123
Bolymin # BC1202AGR. Module: 55.7 x 32.0mm
Ampire # AC162EYI. Module Size: 122 x 44 x
14.5mm. Yellow-green LED backlight.
CAT# LCD-129 $6.50 each
16 X 4 LCD
Optrex # DMC16433.
Module Size: 87 x 60 x 11mm. TN.
CAT# LCD-164
$4.75 each
20 X 2 W/ LED BACKLIGHT
HYeLCD# HC20216NYU-LYV0-03
Module size: 146 x 42 x 13mm.
Display area: 124 x 24mm. Prepped w/ 16 pin
female socket (16 x 1, 0.1” spacing). Green LED
backlight operates on 7.5Vdc.
CAT# LCD-2021
$5.00 each
24 CHARACTER X 1 LINE
Wintek# WDC2401P-1GNNA. Module size: 4.25” x
0.79” x 0.3”. Display size: 3.5” x 0.4”. Built-in driver.
CAT# LCD-111 $1.00 each • 10 for 90¢ each
162 for 75¢ each • 810 for 50¢ each
128 X 64 GRAPHIC LCD
Seiko # G1226B1J. Led back light.
Module size: 3.67" x 2.76" x
0.42" high (93mm x 70mm x
11.4mm) Viewing area: 2.78" x
1.45" (70.7mm x 38.8mm) Built-in RAM.
Wide viewing angle and high contrast.
Slim,light weight and low power consumption.
CAT# LCD-12864
$9.00 each
256 X 128 LCD
Hyundai # HG25504. 5.8" x 4.58" graphic display
module. Viewing area is 5" x 2.75". 5 Vdc logic.
18 Vdc LCD voltage.
CAT# LCD-101 $18.50 each
16 CHARACTER VACUUM
FLUORESCENT DISPLAY
Futaba #16-SD-01Z.
97 x 20 x 6mm,
excluding pc pins.
CAT# VFD-16
$3.00 $1.50 each
MOST ORDERS SHIPPED WITHIN 24-48 HOURS
REDUCED
PRICE !
61